FL-P1 100 pattern Pre-programmed DMX RGB LED Effects
Contents
1. it will turn all fixtures red blue slider up will turn all fixtures blue green up fixtures become green red green blue up at the same time will make white The Dimmer slider also effects the overall brightness To set this button up for a personal FLOOD combination you must press and hold the BANK CHANGE button 3 for a few seconds until FA Fixtures All appears in the display This means that any movement on the sliders will effect ALL FIXTURES Using the blue UP 5 and DOWN 6 buttons you can select individual fixtures F1 to F8 now moving the sliders only adjusts this particular fixtures colour amp brightness Cycle through the fixtures adjusting the colour amp brightness as you go When all fixtures have been adjusted hold down the FLOOD 2 button until SF is briefly displayed to save the flood combination you have created Now press and hold the BANK CHANGE button 3 again for a few seconds the controller will exit the flood setup returning to normal use Now everytime the FLOOD button 2 is pressed you will see your personal flood combination on your fixtures Linking fixtures together You will need to link your fixtures and the controller together in a daisy chain from one fixture to another using standard 3 pin XLR cables Then after setting the dip switches or starting address they will need plugging into their power source Instructions on the following page explain setting the address If you w2. the address settings are always working from 8 channels Below is a guide on how to set your fixtures starting address or dip switches Mi oron O prorr DIPS SETTINGS Fixture 1 DIGITAL 001 017 025 033 041 057 Fixture Codes The separate list of profile codes is a small selection of the most common fixture types For a detailed fixture list visit www ryger co uk d0 d1 d2 d3 d4 d5 d6 d7 d8 d9 are the options available If you are unsure you can simply retry every profile in turn with your fixture connected restarting the controller each time To check the setting is correct hold down the BANK CHANGE button until FA appears in the display You can now operate the RGB sliders one at a time and see if the corresponding colour illuminates on your fixture If they all operate correctly then that is the profile to use if they do not operate correctly then try another profile number Hold down the BANK CHANGE button to exit the FA setup If you correctly identify an unlisted fixture to a profile please email the details to sales rygeruk com so that it can be added to the profile list If you require a custom profile contact Ryger for a costing Controlling Patterns Blackout button The BLACKOUT button 1 provides an instant blackout of all lights connected to this unit It will override all other programs and black out all fixtures that are in use Flood button The FLOOD override button 2 will
3. ATTERN from within each of the 10 BANKS To configure these simply go to each BANK in turn by briefly depressing the Red BANK 3 button and then select a desired pattern using the Blue UP amp DOWN Pattern 5 or 6 buttons You do not need to save this pattern the controller does it when you move to a different bank it always remembers what you had previously selected in each bank amp when you return the pattern will be waiting for you even when you power off This indicates Pattern 5 of Bank 1 blue up down buttons This indicates Bank 1 red button 1 5 Programming and other functions Pattern change PATTERN changes within a BANK are done manually with the blue up down buttons 6 and 7 There are 10 PATTERNS within each of the 10 BANKS giving a total of 100 patterns The MODE Button 8 allows the controller to scroll through the 10 banks automatically There are three modes of operation LED off Manual control Press the BANK CHANGE 3 button briefly to change bank LED on Scrolls through 10 banks automatically i e your 10 chosen patterns LED blinking Scrolls through all 100 patterns automatically Programming your favourite pattern in each bank The pattern programming of this unit is very simple In manual mode just choose a favourite PATTERN using the UP amp DOWN buttons then after pressing the BANK CHANGE button the controller will remember which pattern you have chosen and every time you retur
4. Size Weight Sound Power supply Output Specifications Footlight FL P1 W 250mm x D 170mm x H 70mm 1 45Kg Internal Mic 220 240 Vac adaptor to 9volt DC on controller DMX 512 protocol 64 channels Dealer Stamp Copyright Ryger UK 2010 ver0110 Made in England www ryger co uk Ryger UK Ltd GER Manufacture of Lighting Effects and Control Systems for the Entertainment Industries FL P1 100 pattern Pre programmed DMX RGB LED Effects Controller User Manual Description The Footlight series are easy to use multi function light controllers This footlight is ideal for mobile DJ s bands amp fixed installations or marquee illumination etc This FL P1 features full sound chase blackout 100 chase sequenced patterns speed control two auto pattern modes output dimming and RGB colour mixing for a preferred master flood It is designed to operate DMX enabled RED GREEN BLUE static LED fixtures Parcans etc Minimal DMX knowledge is required by the user IMPORTANT It is important that the set up instructions are fully read in this booklet as they will guide you through the various processes to connect your Ryger LED fixture controller to your LED products Connections Mains Input Is via the 9v 500mA DC transformer supplied with this product Outputs Outputs are made via DMX 512 standard 3 Pin XLR socket Pinl shield Pin2 cold Pin3 hot The serial port is for future PC support not openly
5. available at the moment Sound Input The controller has its microphone and does not require any external connections to source sound input Setup Read this fully Minimal DMX knowledge is required by the user 8 fixtures can be controlled separately with this unit All fixtures you use should ideally be of the same manufacture type or must operate on the same RGB channels check user manuals for this information if you are mixing different fixture types not advised without DMX knowledge The FL P1 can be configured for 10 different profile types of LED parcans bars panels The list supplied will help you choose which type is required and give the corresponding code number that you will need to use to configure the controller for first use PROFILE CODES FOR VARIOUS FIXTURES ARE SHOWN IN THE SEPARATE LIST To first configure the FL Pl you need to hold down the FLOOD button amp then power up the controller then release the button The display will now show d0 d1 etc Using the Blue UP and DOWN Pattern buttons cycle through the options until the number in the display matches the required profile of your fixtures Now press and release the FLOOD button again to restart the controller On powering up the chosen fixture code will flash briefly It will now remember this setting until such times as it is reset or the user changes it This can be easily changed to different makes by repeating the above procedure Providing that all 8
6. fixtures use the same profile they will then operate correctly and access all 100 patterns within the unit Preset Up Step Speed Sound 6 4 Animation Speed 12 13 14 10 Manual Down ae 8 7 35 Auto All Mode Sound R G B Pattern Bank Bank Flood Change Preprogrammed DMX 2 LED Effects 3 Controller 1 BLACKOUT BUTTON 2 FLOOD OVERRIDE BUTTON 3 BANK CHANGE BUTTON 4 SPEED CONTROL 5 SOUND CONTROL 6 UP PATTERN BUTTON 7 DOWN PATTERN BUTTON 8 AUTO MANUAL FUNCTION BUTTON 9 ANIMATION TYPE FUNCTION BUTTON 10 LED DISPLAY 11 MASTER DIMMER 12 RED FADER only used when setting up master flood j i GREEN FADER only used when setting up master flood BLUE FADER only used when setting up master flood 3 PIN DMX OUTPUT on left side 9 VOLT 500Ma POWER SUPPLY INPUT on right side Serial port currently not used on right side pd ph pb pk SA Mn A Optional wall fixing kit available from Ryger DMX VALUES AND SETTINGS In order to gain the most from the controller all of the fixtures have to be assigned their own DMX settings This will either be with dip switches or a digital setting on your fixtures Most of the LED parcans that are on the market currently run on 4 or 5 DMX channels A channel for red blue green and occasionally one for the master dimmer amp presets But the FL P1 runs all fixtures as using 8 channels of DMX to incorporate the par bars amp panels and such like that use more channels So
7. flood all fixtures in one easy movement simply push the button to flood and push again to release back to the previously running sequence This FLOOD button can be user programmed with a favourite flood pattern Bank change button The BANK change button 3 has the function of allowing a user to change through the various different BANKS manually at the the touch of a button This will jump in turn to the pre selected pattern in each of the banks at each press of the button Adjust Pattern Speed or Sound Chase This is done by using the blue ANIMATION 9 button each time this is depressed the associated LED indicator will show what mode of stepping the unit is utilizing LED off Default factory preset speeds LED on Manual Speed adjustable using the rotary 4 LED blinking Sound chase operating adjust sound sensitivity using the rotary 5 The STEP LED indicator blinks everytime the controller pulses steps through a pattern Reading the display in normal use The display 10 is easy to understand at the start it will appear flashing as dO or dl etc This is informing you that the controller is set up for devices of this type as listed in the manual Once the start up sequence has initiated the numbers in the display change amp represent the BANK selection and the PATTERN number 1 e 15 see example below As you start to use the controller you will find these numbers are very useful they enable you to select a favourite P
8. ish to use more than 8 fixtures you will need to duplicate the address settings on the extra fixtures these will then operate in tandem with the first 8 fixtures Some manufactures reverse the hot and cold pins 2 amp 3 on XLR connections if this is the case with yours you will need to make a reversing lead up with one end having wires to pins 2 amp 3 swapped over
9. n to that bank your favourite pattern will run Repeat this procedure for each bank Favourites are stored even after powering off the FL P1 Pattern Descriptions The seperate list of the 100 pattern flood locations indicates what is available in any particular bank If you lose this list check our website for info www ryger co uk Dimmin The controller has a master dimming control 11 which can be varied from off to full brightness The master dimmer affects all channels the amount of slider adjustment required depends on the fixture type being used some are more sensitive than others so this particular sliders effect will vary between manufacturers Use it to take the bright edge off your parcans when in small venues This dimming function can be used at any time with any bank or scene and will not interfere with the program chase that is currently running This slider does not operate once the FLOOD override button 2 has been depressed in normal use Setting the FLOOD overide button The FLOOD button 2 can be easily set up for a personal favourite flood pattern The controller has a separate RED 12 GREEN 13 BLUE 14 level control for each of the three channels which can be varied from off to full brightness The dimmer level for channel one for instance can be altered by sliding the fader up or down to achieve the required brightness or several sliders can be moved to create colour mixing for example push the red slider up
Download Pdf Manuals
Related Search