C - Subaru of America
Contents
1. liner as shown at 3 Reinstall pad to console bin right Rounded corner For operation consult User manual PART NUMBER ISSUE DATE PAGE SUBARU OF AMERICA Du PART NUMBER H621SFG501 DESCRIPTION Forester integration kit for iPod KIT CONTENTS SUBARU Integration kit for iPod Quick reference Console bin grommet 1x User guide guide TOOLS REQUIRED i Nylon trim removal tool PART NUMBER ISSUE DATE PAGE SUBARU OF AMERICA is Note Ignition should be off Starting from bottom pry when disconnecting negative carefully along edges to battery terminal remove trim panel Carefully remove parking brake Remove 2 screws from console boot Remove console screw bin PART NUMBER ISSUE DATE PAGE SUBARU OF AMERICA a C SUBARU Using 14 mm 9 16 drill bit and drill stop set to 2 drill a hole in console bin as shown Caution Feed dock cable C through hole failure to use drill stop may result and tilt console upright as shown in damage to vehicle in slide 9 Pry gently around edges to remove trim panel Note Gear selector must be in N with parking brake set ignition off and vehicle on level ground For manual transmission Route dock cable from bottom of console bin vehicles shift knob must be removed along existing wire harnesses as shown C by unscrewing in a counter clockwise direction Route dock cable tow2. ards front of vehicle as shown Dock cable should be routed behind HVAC controls and up to the radio opening PART NUMBER ISSUE DATE PAGE Senoomsea Via SUBARU OF AMERICA Cz SUBARU Attach module B to bracket A as shown Insert plastic clips to F placing from the bottom up Se Ave N dg SFA my he F WET Use screws G to attach bracket module assembly to vehicle as shown Or Secure dock cable with cable ties D PART NUMBER ISSUE DATE SPN0000582 v1 0 01 14 08 SUBARU OF AMERICA Connect dock cable C to module Secure dock cable to bracket leg with cable tie D Connect bus cable E to module and route behind bracket as shown Connect bus cable E to radio Use the Y harness to reconnect any factory harness occupying the bus connector when applicable Reseat all other connections removed in step 4 secure the unused portion of the harness with a cable tie D and reinstall radio PAGE 4 5 Ga SUBARU 1 Perform 1Pod kit post installation check reassemble vehicle by following steps 1 6 8 10 in reverse For operation consult User manual Lower the console back into position Gently remove excess slack from dock cable C Secure into console bin with grommet H as shown PART NUMBER ISSUE DATE PAGE SUBARU OF AMERICA
3. suBaRU PART NUMBER H621SFG501 DESCRIPTION Impreza integration kit for iPod KIT CONTENTS Quick reference guide TOOLS REQUIRED 4 LF trim removal tool 14 mm drill bit 9 16 Drill with drill stop ICON LEGENDS Remove Disconnect A Location of clip or screw NS PART NUMBER ISSUE DATE PAGE SUBARU OF AMERICA is C SUBARU Note Ignition should be off Starting from panera pry when disconnecting negative carefully along edges to battery terminal Q O remove trim panel M o i KL PNG9S Remove 4 radio screws Carefully remove parking brake For STI models remove liner boot Remove console screw from bottom of console bin PART NUMBER ISSUE DATE PAGE SUBARU OF AMERICA a SUBARU Note It is recommended to drill from the underside of the console to prevent damage to the console bin from the drill Tilt console back Disconnect wire harness and remove console from vehicle Note For STI Using a 14 mm 9 16 inch drill bit models wire routing and connections will differ drill a hole in console bin about 19 slightly mm 34 inch from back edge Pry gently around edges to remove trim panel For STI models disconnect electrical connection Note Gear selector must be in N with parking brake set ignition off and vehicle on level ground For Feed dock cable C through hole leaving 8 9 in manual transmission vehicles shift knob must be
4. the console bin Secure cable to console bin with removed by unscrewing in a counter clockwise grommet H Place console back in position as direction lt I p shown in slide 7 Route dock cable towards front of vehicle as shown Dock cable should be routed behind HVAC controls and up to the radio opening PART NUMBER ISSUE DATE PAGE AN SUBARU OF AMERICA C SUBARU Connect dock cable C to module Secure dock cable Attach module B to bracket A as shown Insert to bracket leg with cable tie D Connect bus cable plastic clips to F placing from the bottom up E to module and route behind bracket as shown Connect bus cable E to radio Use the Y harness to reconnect any factory harness occupying the bus connector when applicable Reseat all other Use screws G to connections removed in step 4 secure the unused bracket module assembl to i i i racke y portion of the harness with a cable tie D and vehicle as shown reinstall radio Secure dock cable with cable ties D Extra cable length should be bundled in this area PART NUMBER ISSUE DATE PAGE SUBARU OF AMERICA SUBARU To provide wire harness access through the liner on STI models Perform iPod kit post installation check 1 Fold pad in half to find pad center reassemble vehicle by following steps 1 7 10 in 2 Atrear edge of pad edge with two reverse rounded corners cut 1 inch long slit into pad For STI models cut console bin
Download Pdf Manuals
Related Search