Manual - SteadiMakers
Contents
1. Battery charging The V Lock battery charger optional accessory is used to charge the battery with a charge time of approximately 3 hours Receiver operation The Director is powered up by ensuring that the V lock battery is fitted or an external supply is connected The front panel on off switch powers the system If the monitor does not come on automatically this is turned on by the monitor PWR button The Rover Director receiver uses the latest form of diversity reception technology to optimise performance Two antennas are used the receiver will however function with only one antenna fitted but best results are obtained in diversity mode Simply connect to the antenna connectors Channel selection is via the rotary switch as per the transmitter module The transmitter and receiver must be on the same channel and be compatible with the frequency allocation of the system in use The demodulated video is supplied to the monitor Two additional composite PAL or NTSC depending on model signals are available via the 750hm BNC outlets Operational status is shown as outlined above When first powered on the receiver will output colour bars until a signal is detected and demodulated If the signal is subsequently lost then the lock LED will go out and the screen will go blank When coherent RF signals are detected again the lock LED will illuminate and pictures will then resume Warning If operating the transmitter very close to t2. Navtech Systems Video Links ROVER Director MkII COFDM Video Receiver User Manual The Rover Director is a portable easy to use hand held receiver with a 7 full colour monitor The Director features dual channel diversity reception to give exceptional performance in the most challenging conditions The Director has an external V lock battery docking port The IDX type V lock facility provides for easy rapid battery changes with operation times in excess of five hours Optional carry case shoulder strap and sun visor for outside viewing in diffused sunlight or in bright studio lighting are available The integrated monitor displays video in either 4 3 or 16 9 format in normal or zoom modes This User Manual also includes the monitior set up procedures to suit the application Top Panel NAWVTECH SYSTEMS Limited Rover Video Link Receiver Up to sixteen RF channel settings are available via a simple rotary switch located at the RH side adjacent to the antenna mount Two LED indicators show Signal Lock and battery power status The LH Lock LED shows blue when a transmission lock is achieved The Power Indicator LED shows Green when input voiltage is above 13 5 V Receiver OK to operate Amber when between 11 amp 13 5 Volts Receiver OK to operate Red when input drops below 11 Volts Receiver will fail below 9 Volts i p change battery The LH side dual Sig
3. AULT 2 Short press button to switch AV1 AV2 mode Default to AV2 gt DISP Display Mode Selects 4 types of display modes Full Normal Wide amp Zoom Note Also used to cancel menu OSD Display gt UP DN Menu Adjustment In Menus press UP or DN button to adjust picture condition level Left Right Reverse Up Down Safety Selection and Reset Default To Disable Safety Mode 1 Make sure monitor is in OFF state 2 Press and hold both DN and UP buttons at the same time then press PWR button until the OSD shows the SAFETY selection menu Release the PWP button then release both the DN and UP buttons at the same time 3 Press DN button to select OFF mode 4 Press again the PWR button to complete this setting After this setting is completed even when you press DEFAULT RESET this setting will not be reset back to ON mode If you want to go back to ON mode you can select the menu to get ON mode Navtech Systems Limited Sulby Nr Welford Northamptonshire NN6 6EZ UK R Telephone 44 0 1858 880 857 Fax 44 0 1858 880 859 IXI E mail sales navtechsystems co uk Web www navtechsystems co uk AT sales navtechsystems co uk www navtechsystems co uk
4. he receiver some signal break up may be observed This is simply due to the receiver input stages being overloaded with too much signal If operating at very close ranges use low gain whip antennas and or remove one of the antennas completely Navtech Systems Limited Sulby Nr Welford Northamptonshire NN6 6EZ UK Telephone 44 0 1858 880 857 Fax 44 0 1858 880 859 IXI E mail sales navtechsystems co uk Web www navtechsystems co uk SN rer ee General advice a The antennas used on both the TX and RX are linearly polarised Try to mount the transmitter so that its antenna is vertical i e same orientation as the receive antennas An SMA right angle elbow is provided with the transmitter to help facilitate this b COFDM links will provide far superior performance to traditional analogue FM links in both high multipath and non line of sight conditions However due care should still be given to ensuring signals can reach the receiver Monitor Set Up Procedures gt PWR Power ON gt OFF When the power is on the green LED on monitor will illuminate gt SEL Menu Selector also Bei aad i AV1 A2 Selection 60 50 ea Fy Earphone Jack Remote Control Sensor Power ON OFF 1 Press for 2 seconds to switch menus The cycle is as follows LED BRIGHT CONTRAST Menu Selector COLOUR TINT k DIMMER LEFT RIGHT es UP DOWN SAFETY do pean not change DEF
5. nal Level LED bar graph shows the signal strength of each channel The amber LEDS indicate low to medium signal reception green indicates good usable signal levels A A CEE SAU lt a Se ee ar AT Navtech Systems Limited Sulby Nr Welford Northamptonshire NN6 6EZ UK Telephone 44 0 1858 880 857 Fax 44 0 1858 880 859 E mail sales navtechsystems co uk Web www navtechsystems co uk Video amp Audio Output Composite video output is available via the two BNC s on the LH side panel If configured for audio two RCA Phono connectors provided the audio outputs Antennas For diversity operation two N type antenna connectors allow for high gain N type antennas to be attched or the smaller lower gain styles using N type to SMA adapters The antennas can be detached for storage or transportation in the carry case External Power External DC is input via the side mounted connector The receiver can be operated from an external 12V DC 10 16V DC supply drawing approximately 1 2A Warning If higher voltages are applied the unit will be damaged Power is applied via a 4 pin XLR or optional 2 pin Lemo connector The centre mounted rocker switch must be set to the I position to select external power input and the IP position for battery power Battery operation An external V lock battery may also be used to power the Director that will give approx five hours continuous use when fully charged
Download Pdf Manuals
Related Search