USER MANUAL - Tanning Bed Parts
Contents
1. Weight pounds Minimum Room Size Electrical Voltage AC 220 220 Amperage 12 16 Circuit Breaker Amps 20 20 Outlet NEMA standard Cr 6 20R C 6 20R Main Lamps GOLDEN TANTM 100W 100W 80W Ballasts 100W 100W 80W Face Tanner NA SolarMax IFT FT Ballasts NA 400W Timer System Electro mechanical Electro mechanical Max Exposure Time 20minutes 20minutes Back up Timer Solid state Solid state CALL FOR SERVICE OR QUESTIONS 1 800 4493605 ETS Inc 6270 Corporate Drive Indianapolis IN 46278 2900 26RS 26RST Size Weight pounds 291 315 Minimum Room Size 6 x 8 6 x 8 Electrical Voltage AC 220 220 Amperage 14 15 Circuit Breaker Amps 20 20 Outlet NEMA standard Cr 6 20R C 6 20R Main Lamps GOLDEN TAN 100W GOLDEN TAN 100W Ballasts 100W 100W Face Tanner NA Turbo Sun amp S FT Ballasts NA 30W Timer System Electro mechanical Electro mechanical Max Exposure Time 20minutes 20minutes Back up Timer Redundant Solid State Redundant Solid State AA y CALL FOR SERVICE OR QUESTIONS 1 800 449 3605 6270 Corporate Drive Indianapolis IN 46278 29002. Clean and disinfect your tanning bed s bench and canopy after each use Use a non abrasive disinfectant cleaner that does not contain ammonia or ammonia deriva tives Ammonia may damage the acrylic shields Spray the acrylic lightly with disin fectant and wipe dry with a clean soft cloth We recommend SunQuest disinfectant and SunQuest acrylic cleaner A WARNING Shock hazard Disconnect power before removing any protective covers Thorough Periodic Cleaning Introduction The cooling fans draw air through the bed and over time will cause a dust buildup on the lamps and reflectors This will reduce the tanning effectiveness of the bed When a dust buildup is observed it is necessary to thoroughly clean the inside of the bench and canopy Cleaning the Canopy and Bench 1 Remove the acrylic shields and lamps as described in Replacing Lamps 12 Rare and Maintenance 2 With a soft cloth wipe the entire length of each lamp to remove any film buildup 3 Clean both sides of the acrylic shields with a non ammonia disinfectant cleaner 4 Wipe the reflectors with a clean damp cloth 5 Re install the lamps and acrylic shields Mechanical Inspection Your tanning bed has been built for years of service To ensure trouble free operation throughout its life inspect the unit s mechanical integrity every 400 500 hours of use Inspect the unit s fasteners verifying that all are firmly in place Pay partic
3. 17 M 24RS REDUNDANT TIMER RELAY BALLAST CONTACTOR CAPACITOR gt o 2 J G S Zo ne LO LU Sr ng O Q npe 5 I xo IL O LL nw O m ni EL c m A o gt 77 c LU or gt E O O GAS SPRING LAMP HOLDERS LAMPS ENDCAP TIMER KNOB TIMER VLO ZOLSZ M 24RSF CONTACTOR RELAY BALLAST CAPACITOR TRIM PROFILE REDUNDANT TIMER ij YA N SAN PR N LU LL O X A COVER BENCH LOCK SILK SCREENED PROFILE GAS SPRING TIMER KNOB TIMER SWITCH FACE TANNER LAMP HOLDERS LAMPS ENDCAP LEGS M 26RS A S EN INS U s GAS SPRING REDUNDANT TIMER RELAY M USA CONTACTOR ENDCAP LAMP HOLDER LAMPS X O m 5 Se 8 gt lt X LU Lu a r O ui O z gt lt _ o IX H gt SEX 24 Zo w zWo gt zr 3 OB a LU Zu ul W a LL LL OO O or Y m o i a Fr M 26RST X x 5 E Wu O o 8 5 lt JE T lt A E LLI E x 4 caa Z oz I lt n E MTT zr x 59 E lt N 2 z Z E VA Uae x V E E 7 N ic LRAT N ja gt CYP TE os 5 Y J z AN lt O ad i LLI E E gt E Obs 52 E sho EE Ox o amp OO a Ts z LLI E m O 2 X e 4 gt y 2 3 E OY CP 3 LAMPS LEGS Parts List This is a list of parts which may be replaced by the consumer Care should be
4. power is disconnected tighten the threaded locking ring before connecting cables Na MAIN AC POWER CORD THREADED 2 Plug the three prong 220V AC power LOCKING N cord into a dedicated outlet see Pre Installation Planning RECEPTACLE ON BENCH CANOPY TO BENCH POWER CORD VLO ZOLSZ 25107 01A we A JE peration ma Before You Tan Before using your sunbed please note the following important precautions e Your skin should be free of cosmetics tanning oils or other body lotions prior to tanning except for those specifically made for use with tanning devices However do not remove nat ural body oils by bathing or showering immediately before tanning e Your hair should be free of gels mousses sprays or other hair products prior to tanning These products can cause damage to the sunbed acrylic As an alternative a shower cap or towel can be worn to keep treated hair away from the sunbed surfaces A DANGER Shock hazard Do not operate this device near water or while you are wet RECOMMENDED EXPOSURE TIMES IN MINUTES Level 1 Week 1 Ist 3rd Sessions Skin Type I Sensitive Skin Burns easily and severely and does not tan Burns easily and severely and tans minimally Burns moderately and tans average Burns minimally tans easily and above average II Light II Normal IV Dark A DANGER Some medication may increase your sensitivity to ultraviolet light It is re
5. radiation during the first 50 hours of operation Recommended tanning times should therefore be reduced by approximately 1096 during that period WARNING Read the instructions booklet before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear provided eyeshields or equivalent eyewear as defined under 21 CFR 1040 20 Other types of eyewear may not provide adequate protection Failure to use protective eyewear may result in severe burns or other eye injury If discomfort develops discontinue use and consult a physician THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RS MODEL SERIES GOLDEN TAN Wolff Model GT71 T12 100W BI PIN THE FOLLOWING ADDITIONAL LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RST MODELS Turbo Sun S Wolff Model F8 T5 10W Turbo lamps THE FOLLOWING ADDITIONAL LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RSF MODELS GOLDEN TAN Wolff amp Model GT59 T12 80W BI PIN Short Lamps Heraeus E400 HPT Philips Model HPA 400 30s or CosmoTech Model 23045 SolarMax IFT Face tanner unit DISCONNECT POWER CORD BEFORE ATTEMPTING TO CLEAN RELAMP OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT THIS EQUIPMENT MUST BE EARTH GROUNDED This product is in conformity with performance standards for sun lamp products under 21 CFR PART 1040 20 LISTED and ANSI UL Standard 482 88465 Ut US VLO ZOLSZ 25107 01A E AG nstallation Unpacking and I
6. taken when replac ing anything related to electrical wiring We rec ommend contacting a professional electrician When calling for parts first state your bed model as M 24RS M 24RSF M 26RS or M 26RST Then refer to this list and preceding illustrations for proper part identification Acrylic Bench Acrylic Canopy Ballast 30W for Turbo lamps Ballast 80W for short lamps on 24SF Ballast 100W 1 for each main lamp 4 for each face tanner lamp Capacitor 75uF Contactor Relay Cover Bench Cover Canopy Endcap Kit 1 left and 1 right endcap Fan Gas Spring set Hardware Kit assembly hardware Hinge Brackets left and right Keys Parental Lock Lamp Holder Turbo Lamp Holder w Starter Lamp Holder w o Starter Lamp Holder Face Tanner Lamps Leg Mounts found inside the bench Legs Manual Pillow Profile blank Redundant Timer Schematic Packet Silk screened Profile Starter S 2 Turbo Starter K 11 main lamps Starter Face Tanner ignitor Starter Holder Turbo Switch Face Tanner Switch Parental Lock Thermostat Face Tanner Timer Timer Bezel Timer Knob Trim Profile blue Not shown Record this information for ease of service Date of purchase Bench serial number Canopy serial number CALL FOR SERVICE OR QUESTIONS 1958005449 3605 ETS Inc 6270 Corporate Drive Indianapolis IN 46278 2900 VLO ZOLSZ 25107 01A 24RS 24RSF Size
7. the lamps replace the acrylic shields by reversing the above directions Close the hinged profile by pushing it back into place until it snaps tight A CAUTION Be careful The edges of the acrylic shield may be sharp 13 N p A Removing Replacing Lamps After removing the acrylic shields replace lamps as follows Step 1 Grasp a lamp at one end and at the middle then turn the lamp a quarter turn The lamp may then be gently removed from its holder Step 2 To reinstall a lamp insert the pins located on the ends of the lamp into the slots on top of the lamp holder and turn the lamp a quarter turn s Care and Maintenance Replacing Lamps Recommended Replacement Lamps We recommend using the lamps specified below Use of uncertified lamps is a viola tion of Federal regulations and will void your warranty These lamps have an aver age life of 800 1000 hours of effective tanning use Lamps used longer than that begin to lose their effectiveness even though they will continue to light A WARNING Shock hazard Disconnect power before servicing THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RS MODEL SERIES GOLDEN TAN Wolff amp Model GT71 T12 100W BI PIN THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RST MODELS GOLDEN TAN Wolff Model GT71 T12 100W BI PIN Turbo Sun amp S Wolff Model F8 T5 10W Turbo lamps THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE RSF MODELS G
8. unfiltered light can be seen escaping face tanner assembly SCREWS RETAINING 15 NY 3 Al 7 KUSI Timer Maintenance Your SunOuest sunbed is eguipped with a backup shut off timer which will automat ically turn off the sunbed in the unlikely event of a malfunction of the primary timer This important safety feature also prevents the user from re setting the timer before the end of the pre set maximum time interval The electronic timer limiting circuit is automatically reset each time the primary timer is turned to the OFF posi tion Annually or whenever your sunbed is re lamped check the operation and accura cy of the timer system as follows DO NOT perform these tests with a person in the sunbed 16 R Care and Maintenance Timer Maintenance Step 1 Obtain an accurate watch capa ble of measuring in seconds Set the timer to its maximum inter val Using the watch time how long the lamps remain on The lamps should shut off within plus or minus 1096 of the maxi mum timer interval Set the timer to the maximum time interval Wait ten minutes then turn the knob back to the maximum time position The electronic time limiting circuit should turn the lamps off at an elapsed time equal to approxi mately 1096 beyond the maxi mum timer interv
9. OLDEN TAN Wolff Model GT59 T12 80W BI PIN Short Lamps GOLDEN TAN Wolff amp Model GT71 T12 100W BI PIN Full length lamps Heraeus E400 HPT Philips Model HPA 400 30s or CosmoTech Model 23045 SolarMax IFT Face tanner unit 14 VLO ZOLSZ 25107 01A Care and Maintenance Replacing Lamps Removing Replacing SolarMax IFT Face Tanner Lamp on F Models After removing the canopy acrylic shield replace the face tanner lamp as follows Step 1 Support the face tanner assembly with your hand while unscrew ing the two retaining screws The face tanner glass casing will swing downward Step 2 The lamp can now be exchanged The lamp holders are eguipped with spring con tacts which enable the lamp to be removed easily Remove the old lamp and discard Install the new lamp using a clean cloth or paper towel Ensure that the lamp is firmly seated in the lamp holders ako e A GS Note Never take hold of the lamp such that your fingers are in contact with the lamp glass Finger oils will greatly reduce the lamp s operational life Step 3 Gently close the face tanner glass casing and lock it closed with the screws Ensure that the screws firmly secure the glass casing A DANGER Unfiltered light from face tanner can cause severe burns Never turn sunbed on while face tanner is disassembled or when glass filters are removed Immediately discontinue use of this equipment if face tanner glass is broken or any
10. SunQuest 24RSF 26RS 26RST Pro 24RS USER MANUAL Limited Lifetime Warranty SunQuest warrants your tanning unit to be free of structural defects in its material and workmanship under normal use for its lifetime SunQuest will repair or replace at their discretion any defect to the structure which affects the performance of the unit For 6 months from the date of purchase SunQuest will provide replacements for parts that prove to be defective in material or workmanship Acrylic shields fluorescent lamps and lamp starters are excluded from this warranty Labor will be covered for 30 days from pur chase date Normal wear damage from misuse or abuse damage incurred in transit or damage done by unauthorized repairs or modifications are not covered by this warranty ETS Inc disclaims any implied warranty of merchantability or fitness for any period beyond the expressed warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you No one has authority to change or modify this Limited Lifetime Warranty in any respect To obtain service under the Limited Lifetime Warranty contact ETS Inc at 1 800 449 3605 and ask for the Technical Service Department ETS Inc shall not be liable for loss of use loss of time inconvenience rental or substitute products loss of business loss of income or any other incidental or consequential damages Some state
11. al even though the primary timer con tinues to show time left Step 2 Call ETS Customer Service if your timer does not operate properly or if you expe rience difficulty with these tests VLO ZOLSZ 25107 01A Problem Lamps fail to light One or more lamps fail to light Canopy fails to stay in the up or down position Sunbed does not stay lit Solution Check source of AC power Reset circuit breaker or replace fuse if necessary Make sure the unit is plugged into outlet Make sure cord between canopy and bench is properly connected Make sure timer dial is turned to a number past 0 Make sure Parental Lock is in the vertical position Check that lamp is installed correctly Switch unlit lamp with a lamp that lights If the new lamp lights and the old lamp still does not replace old lamp If replacing lamp does not remedy problem con tact your service representative Gas springs should hold the canopy fully open as well as allow it to rest fully closed If the canopy is left open for an extended period of time it may creep down This is considered normal Keep the canopy closed when not in use Replace gas springs when they no longer have sufficient power to hold the canopy open when raised Check source of AC power Reset circuit breaker or replace fuse if necessary Check timer system per maintenance instructions in this guide Contact your service representative
12. are ready to use your sunbed Proceed as follows Your sunbed is designed for individual use Always wear the safety goggles sup plied with your sunbed or another approved pair of goggles as defined under 21 CFR 1040 20 Regular sunglass es do not provide adequate protection from ultraviolet light A WARNING Wear protective eyewear Failure to may result in severe burns or longterm injury to the eyes YY M Operation Using Your Sunbed e 4 Step 1 Step 2 Step 3 Step 4 Per For units equipped with a face tanner activate the face tanner by placing the rocker switch located below the timer knob into the I ON position If you do not wish to use the face tan ner leave the switch in the O OFF position NOTE The F model face tanner lamps require a cooling period before they will light again Put on your goggles Set the timer to the desired number of minutes after first determining the proper time period from the table in Exposure Times The lamps will turn on as soon as you move the rotary dial past the 0 position Lift the canopy lie down on the bench face up and lower the canopy toward your body main taining minimum distances as described in Safety Information When the timer reaches 0 the lamps will automatically turn off and the cooling fans will run for approximately 3 minutes during the Cool Down period 11 M M EC PR ve P Cleaning After Use
13. c ommended that you consult a physi cian before using this sunbed if taking any medication or if you suspect that your skin might be especially sensi tive to sunlight Included with this manual is an FDA booklet on medica tions that increase sensitivity to light Exposure Times Follow the guidelines for skin type and exposure times as shown in the table below Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approxi mately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan MAXIMUM EXPOSURE TIME IS 20 MINUTES Subseguent tevel 4 Maximum Level 2 Level 3 NOT RECOMMENDED FOR TANNING 8 12 16 20 10 15 20 20 12 16 20 20 NY E 3 Operation Parental Lock Mis Parental Lock This sunbed is equipped with a parental lock switch This switch helps you monitor usage of the sunbed by children and or others To activate insert the key into the lock switch and turn horizontal to lock and vertical to unlock illustration shown unlocked You may remove the key in the unlocked as well as locked position FACE TANNER ROCKER SWITCH 10 VLO ZOLSZ 25107 01A Using Your Sunbed Once you have read Before You Tan and Exposure Times you
14. eee nad APPAR Dat e RR E es 9 Exposure TIMES pps fos ehh ree ERR ba Ase PIS Eie 9 Parental Lock ccoo bd dha bd RO kattaisi hos dad edad 10 Using Your S nbed essc SPADES Gee EE PRAWENUSS 11 Care and Maintenance ssa cese a kaunaa bd eheu a cb 12 Cleaning After Use lt lt s ae aaah d dia ER a 12 Thorough Periodic Cleaning lt lt 12 Mechanical Inspection 2 2 0 0 00 000 e eee eee ee 12 Replacing Lamps lt lt eee eee 13 Timer Maintenance mua cide tp K 8 ab SESS Meses 16 Troubleshooting lt sss ss z SENA EN rr ER 17 Obtaining Service 4 4 4444 back cover AM M 4 Ae gt Aiafety Information PR LABELING NOTICE Labels are affixed on all systems to inform the user of possible dangers Regulations are stated in 21 CFR Section 1040 20 and require that all products manufactured after September 8 1986 which use sunlamps must display the following DANGE Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin cancer WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or have a history of skin problems or believe yourself especially sensitive to sunlig
15. ewear Failure to may result in severe burns or longterm injury to the eyes ed M o KA EL AN s Installation Assembly Procedures PR Attaching Legs to Bench Lay the bench upside down on the floor Locate the two stand legs and attach to the bench as shown below 2 Turn bench right side up on floor Place so that the power cord connec tor is facing toward the wall outlet Using six 5 16 x 1 bolts and six larger 5 16 washers pre installed remove from bottom of sunbed attach the stand legs with the skirt mounting holes toward the back of the bench as shown Install center bolt first You may have to gently push sides of legs in to align holes Tighten with the Allen wrench SKIRT MOUNTING HOLES ELECTRICAL CONNECTOR INDICATES BACK OF BENCH VLO ZOLSZ 25107 01A Attaching Hinge Brackets to Bench Locate the two hinge brackets and identify the left and right brackets 1 Install the hinge brackets to the ends of the bench such that the short boss engages the stud above the bolt hole and the long boss engages the hole below the bolt hole Secure using the 5 16 x 1 Allen head bolts and 5 16 metal washers Tighten bolt snug then an additional half turn Installation Assembly Procedures A Pr RUP e 2 Place the bushings into the hinge brackets as shown below ed M Po 1 PR Attaching Canopy to Bench Lift the canopy and hold it between the h
16. ht If you do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this equipment To use lie down under canopy and pull down as far as adjustment will allow maintaining at least 2 inches 5 1 centimeters between your body and 26RS series canopy clear plastic panel Minimum use distance from face tanner is 1 inch or 2 54 centimeters Minimum use distance elsewhere is touching the clear plastic panels Do not use without clear plastic panels in place Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTES Level 1 Week 1 Level 2 Level 3 Level 4 Subsequent Skin Type Ist 3rd Sessions Maximum I Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING II Light Burns easily and severely and tans minimally 8 12 III Normal Burns moderately and tans average 10 15 IV Dark Burns minimally tans easily and above average 12 New lamps emit approximately 10 more ultraviolet
17. inge brackets You may want to use some of the cardboard packing laid across the bench to support the canopy 2 Insert the 5 16 x 1 1 2 bolts with the nylon washers into both hinge brackets Tighten bolts into the end cap threaded inserts until snug then an additional half turn Do not over tighten to avoid damaging threaded inserts VLO ZOLSZ 25107 01A Attaching Gas Springs 1 The gas springs are shipped with locking clips installed Use a screw driver to pry back the locking clips on the gas springs as they are installed See right 2 With a helper holding the canopy open align open ends of gas spring ball joints with pivot studs and push into place Be sure rod end is down as shown DO NOT lower canopy until both gas springs are engaged Installation Assembly Procedures A lt D d CS 3 Lift and lower canopy a few times to lubricate gas springs for optimum performance LOCKING CLIP MEN SCREWDRIVER PIVOT STUD N 2 Re Installation Making Electrical Connections PR Making Electrical Connections 1 Connect the canopy to bench power cord to the bench receptacle The A WARNING plug is polarized Align the terminals Shock hazard and firmly push on until seated then Be sure AC
18. nspection Your sunbed comes in two cardboard car tons one for the bench and one for the canopy Open the cartons and remove the bench and canopy as follows The bench and canopy are each wrapped in plastic Pull back the plastic and with a helper grasp the bench and pull it from the carton bottom leaving the plastic wrap and the carton packaging Do the same for the canopy Do not try to lift either unit with the plastic still on as it may slip Note The cartons are reusable You may wish to save them for future use The canopy box contains the canopy unit and a pair of gas springs The bench box contains the following items e Bench Unit e Box containing necessary assembly hardware safety goggles and pillow Box containing two stand legs Inspect these items including the canopy and bench and make sure they are free from any visible damage Report the extent of any damage to the transportation company Record the serial numbers of the canopy and bench in the area provided at the back of this manual This information will be required whenever you call customer service ed M N K Installation Pre Installation Planning Pre Installation Planning Before you begin to assemble your sunbed you should observe the following pre installation considerations A WARNING Shock hazard Disconnect power before servicing e Your sunbed operates from a 220V AC source You should have a NEMA 6 20R elec
19. s do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state All warranty service must be performed by an authorized service person If your tanning unit must be returned for service all freight charges must be at your expense Contact your place of purchase for the address of the SunQuest Service Center nearest you Proof of purchase is required to obtain warranty service This warranty covers the original purchaser only This warranty is void if the unit is modi fied in any manner from its original design VLO ZOLSZ 25107 01A Me M AMA Fi m come Congratulations on your purchase of this technologically advanced sun tanning unit It has been designed to provide years of dependable service for you Please read all the instructions in this booklet before installing and using the unit Always be sure to observe all safety precautions P M Joke gt ME Ontents TR Safety Information osuu eee eee eee eter eee eens iii Installati n ss asas pesa dada d sad sek 1 Unpacking and Inspection 2 slkn ce eee eee 1 Pre Installation Planning 0 0 0 0 nen 2 Assembly Procedures lt 3 Making Electrical Connections lt 8 Operation z 3 5 e Sees S Vee da eee eR ESPERE 9 Before YOu Iani
20. trical outlet like the one shown below installed in the room in which you will use the unit The outlet should be on a dedicated cir cuit capable of providing 20 Amp service We recommend installation by a professional electrician The outlet must be earth grounded 20 AMP NEMA 6 20R RECEPTACLE A CAUTION Use of a voltage source above 230V AC may prevent proper operation of the sunbed and could cause damage and void the warranty A CAUTION Air from the room is used to cool the sunbed Maximum ambient room temperature should be 80 F Place your sunbed no closer than 6 from any wall Make sure nothing obstructs the airflow into the sunbed s endcaps or out of the fan openings A poorly ventilated room may cause the unit to become hot and cause discomfort to the user A CAUTION Proper assembly of your sunbed requires three people Plan to have a couple of helpers assist you VLO ZOLSZ 25107 01A we Installation Assembly Procedures A ma Allen head Bolt 5 16 x 1 Assembly Procedures Hardware Inventory ity 2 Open the hardware box and remove the Sau small bag of hardware In addition to a pillow make sure you have the following 5 16 Metal Washer hardware items NA Quantity 2 Bushing Quantity 2 1 4 Allen Wrench Quantity 1 Nylon Washer Quantity 2 Safety Goggles Quantity 1 Hinge Brackets Ouantity 2 left and right A WARNING S Wear protective ey
21. ular attention to the hinge bolts Inspect gas springs for signs of wear Gas springs that will not hold the canopy in the full open position when raised should be immediately replaced Inspect the timer as indicated in this manual under Timer Maintenance Inspect the AC power cord and its connections Inspect the acrylic Broken cracked or badly scratched acrylics should be immediately replaced VLO ZOLSZ 25107 01A dd Care and Maintenance Replacing Lamps E Replacing Lamps Introduction To be assured of maximum tanning effec tiveness change lamps after approximate ly 800 1000 hours of use Tanning will continue after this time but at a slower rate To ensure trouble free operation of your sunbed replace the lamp starters whenever the lamps are replaced A WARNING Shock hazard Disconnect power before servicing Removing Replacing Acrylic Shield The acrylic shields in the bench and canopy are secured in place by hinged profiles which run the length of the bed both front and back Simply pry up on the inside edge of the profile until it releases its latching action see figure at right Continue to pry up the profile across its entire length until it swings back freely Repeat for the other profile The long edges of the acrylic shield are now exposed Standing in front of the sunbed grasp the exposed edge of the acrylic and carefully slide it toward you until it is removed After changing
Download Pdf Manuals
Related Search