DataLink Release Notes
Contents
1. Build 3 8 4 10 25 2011 1 Improved SmartWire interface 2 Added Help button to SmartWire dialogs 3 Added Read and Write shortcuts to toolbar Build 3 8 5 12 12 2011 1 Added support for SmartWire Switch Module Build 3 8 6 1 Added support for Torque Meter 2 Added support for RESET command parameter 3 Added support for AF4S Build 4 0 3 08 07 2012 Added ability to program the G2X Engine RPM source via DataLink Fixed issue that could corrupt the SD card when selecting the Force New Recording on Next Power Up button on V300SD and Sportsman configuration files Display a dialog box to allow telemetry setup after adding new channels Added ability to start a new data telemetry session with just two mouse button clicks Display confirmation when saving files Added default configuration button to toolbar Added support for GoPro Hero interface module Added support for Texense 8 channel IR temperature sensor module Nae oo NQARA TDR Build 4 1 1 09 28 2012 1 Fixed issue that could cause the COM port to hang 2 Enabled SmartWire Print Report button 3 Added compatibility for transducer box firmware version 10 and higher to allow RPM channels Build 4 2 0 01 15 2013 1 Improved video playback performance and added slow playback feature 2 Added support for PROIIIA 3 Added support for V500SD 4 Added ability to select the data logger file when exporting data to Track Vision Build 4 2 1 05 14 2013 1 Added2. Reading or Writing Config fails Real time telemetry COM ports is now set under Setting gt Preferences COM Port option instead of the inside the configuration file Added dialog boxes for IQ3 Added canparm files to support the following devices a 1Q3 display only dash b 1Q3 logger dash c USM d Racepak 4 channel air fuel module e Racepak single channel air fuel module Added the following CAN ID s a Air Control 1 5 under new category Air Control b Nitrous Stage 4 Move nitrous ID s from Fuel category to new category Nitrous Changed all reference in CanID canset from PSI to Press Build 3 0b 2 16 2008 1 2 Added support for more than 4 characters on IQ3 display tags Added IQ3 configs for boats and pullers Build 3 0c 2 25 2008 1 Fixed incorrect channel linking to GPS gap correction on IQ3 config files 2 Added IQ3_config support for version 3 firmware which added gear logging 3 Added the following canparm files a Haltech_ECU canparm b GenCan_Mod canparm Build 3 1 0 3 24 2008 1 The version numbering method has been changed from X to Changed help system to be compatible with Windows Vista Modified some of the IQ3 dialog boxes Added option in Setting gt Preferences to disable the X that appears on the time cursor Changed the terminology used in some of the menu and dialog boxes DataLink setup program now installs the Racepak USB to Serial port adaptor driver automati
3. support for Link Vipec EFI CAN interface module Added Yes to All and No to All option when performing a Read VNET Config Added support for PROIII warning and shift light modules Fixed issue that would not allow the user to change the VNET ID on Smartwire switch input channels Fixed issue that could cause DataLink to display incorrect configuration values after clicking the READ Configuration button Added Bluetooth support for PROIII and PROIIIA ONOoaBRWND Build 4 3 0 09 17 2013 1 Added the ability to skip missing VNET channels when performing a Write VNET Config 2 Added the ability to enable disable the power on bulb check on the 4 channel warning module 3 Added the ability to enable disable the warning tag on the bottom of the IQ3 display 4 Fixed issue that could cause Datalink to crash when uploading a ddf file with Smartwire channels Build 4 3 1 10 17 2013 1 Added support for FuelTech interface module Build 4 3 2 11 26 2013 1 Updated support for Link G4 Vipec EFI CAN interface module 2 Added support for Atomic LS EFI interface module 3 Added support for Microtech ECU 4 Added support for USM_V2 Build 4 3 3 02 25 2014 1 Added support for MSD 8771 2 Updated scalings in Hondata canparm file Build 4 3 4 04 02 2014 1 Added support for Atomic TBI interface module Build 4 4 0 05 13 2014 1 Fixed issue that was causing some transducer boxes to disappear when using the Sho
4. DataLink Release Notes Build 2 5d 10 05 2005 JG 1 2 Added CG plot to G2X_Demo rpk Added can parameter files to support new round gauge product types Build 2 5f 1 12 2006 JG Added CAN_GAUGE canparm file for backward compatability Modified J1939_MOD canparm file in the following way a Changed max ECU number from 4 to 255 Modified G2X_STB_10bit canparm and G2X_STB_16bit canparm in the following ways a Changed max smoothing from 500 to 100 points b Changed Delay after Reboot from 1000ms to 1500ms to fix problem with changes sometimes not taking Modified SC_ANALOG canparm file in the following way a Added sensor type for IR temp sensor 810 SN IR TEMP Fix unsupported TMDATA error when attempting to upload data from V500 with individual timing enabled Fixes displaying warnings for every packet when uploading data from a CF or SD card using multi block data storage method i e G2X Build 2 8a 12 18 2006 JG 1 2 3 Added DataLink support for metric track mapping Added G2X_Config_Metric rcg for G2X metric runlog support Added G2XPro canparm support files Build 2 8b 12 27 2006 JG Fixed bug in metric distance scaling in DataLink Fixed bug in product type in file G2XP_Analog canparm Added file G2X_Event canparm Build 3 0a 1 16 2008 JG Added ability to scan for Racepak hardware on serial ports 1 10 and set the proper COM port if a valid device is found User will now be prompted whether to scan COM ports if
5. cally for Windows Vista and XP Fixed problem that would not allow some users to open Boat Demo file Updated IQ3 pdf user manual to version 2 Oo WD o N Build 3 1 1 3 27 2008 1 Fixed problem that could cause program to crash when downloading data in v3 1 0 2 Removed New File Naming Scheme option from the Settings gt Preferences menu Build 3 1 2 4 17 2008 1 Fixed issue that was causing the radio button for the OR AND option to not function properly in the 1Q3 warning dialog box 2 Added a calibration table in the Universal Sensor Module for 100 PSI resistive pressure sensors Selecting this sensor type will automatically setup the User Cal Table Values The table is optimized for Racepak part number 810 PT 0100SD However the table should work with most other 100 PSI resistive type pressure sensors with little or no modification 3 Fixed error in Universal Sensor Module CAN parameter file that was causing the User Cal Table Value at 1 25v to not send properly Build 3 1 3 5 28 2008 1 Fixed issue in IQ3 display canparm file that was not allowing the user to set the decimal on bottom center display on page 3 2 Added support for AF1 wideband controller 3 Added support for Chase Cam control module Build 3 2 0 6 28 2008 1 Fixed issue that was causing LapT Difference channel to not display properly under certain circumstances 2 Fixed issues that was causing program to hang when opening a data file with referenc
6. e lap selected 3 Added support for the following VNET devices a Haltech b XFI CAN 4 5 c Bosch 3 20 d Big Stuff CAN Added configuration file for IQ3 display only dash NonLogger Fixed error in DFl_MOD canparm file Build 3 2 1 7 18 2008 1 2 3 4 Updated support for Big Stuff 3 ECU Added support for BSG ECU Added an error message when attempting to write the start finish position file to a write protected memory card Added user programmable stop record value and delay time for IQ3 and G2X This feature also requires a firmware update Build 3 3 0 10 17 2008 1 2 3 8 9 Added new video player Updated canparm file for CHASE CAM module When uploading data from memory card detailed view is now shown so you an see the date and time the file was created CURRENTLY THIS FEATURE DOES NOT WORK ON VISTA FUTURE VERSIONS WILL SUPPORT VISTA FOR THIS FEATURE Added the ability to program when to display the number of acquired satellites in center display for the IQ3 REQUIRES IQ3 FIRMWARE VERSION 8 OR HIGHER Added RPM Speed Ratio calculator on IQ3 Gear Calculation tab Segment Report page now has the ability to exclude segments from the Theoretical Fast Lap calculation This feature requires you to install the new IQ3 or G2X Config file when prompted at the Racepak product selection page Segment Report page now has an Up and Down arrow to allow the viewing of laps that go beyond the bottom of the pa
7. el button window pane Selection can be made in Setting gt Preferences Added ability to change the channel button width Selection can be made in Setting gt Preferences 7 Modified Message Log dialog to hide communication details unless an error occurs 8 Fixed issue that could cause incorrect time offset in PROIII magneto current channels 9 Added the ability for the IQ3 to read the number connected VNET channels connected Requires IQ3 firmware version 15 or higher 10 Added OBDII module support oR WD O aS Build 3 8 2 5 19 2011 1 Added Smartwire canparm file option during installation Only needed for use without a Racepak data logger 2 Added ability to update the Smartwire firmware via DataLink 3 Added canparm files for Traction Products transmission controller 4 When a configuration file is opened and selected clicking File gt Save As will result in the rcg file extension to be selected instead of rpk Build 3 8 3 08 09 2011 1 Highest COM port is no longer limited to COM9 2 Added support for AEM CAN interface 3 Added support for PROII magneto current logger 4 Added support for Smartwire set point delays Also requires firmware v14 Fixed Smartwire graph smoothing control disabled on data file Added terminator resistor on off option to Switch Panel dialog box Fixed GPS data offset issue introduced in DataLink v3 8 0 Fixed issue causing incorrect video sync time with Trackvision export CONDOM
8. face module Added support for Pro III data logger Added support for Racepak single wire temperature sensor to USM The data and config file format has changed in this version Any new files that are created or previous files that are opened and saved in this version will not open in any previous DataLink version It is highly recommend that you update all of your PC s Build 3 7 0 03 25 2010 1 CONDOM Perera Added ability to record and display GPS date and time on Session runlog page Requires configuration file update and the following firmware versions e 1Q3 v14 e G2X Red v14 e G2X Black v45 e G2X Pro v56 Fixed issue that could cause the scroll left and right buttons on the Segment Compare page to work incorrectly when the Ref Run Lap and the Selected Run Lap were from different data files Fixed issue that was causing the GPS_Satellites channel to display incorrectly when real time telemetry was running Fixed issue that could cause the GPS data to shift incorrectly if a new recording was started before a GPS fix was acquired Added support for Megasquirt amp II Modified Pro III accelerometer canparm files Added signed driver installation for Racepak USB devices Double clicking on a DDF raw data file will now launch a new instance of DataLink and start the new upload process The USM channel calibration tool now calculates the end point slopes out to Ov and 5v 9 10 Added support for V300 HD Destroye
9. ge This feature requires you to install the new IQ3 or G2X Config file when prompted at the Racepak product selection page Added support for ViPEC interface module Windows98 installations now requires Media Player 9 or higher installed 10 DataLink installer is now combined to support both 1Q3 G2X and V Series installations There is no longer a different CD for each type The user must now make a product selection during the installation process Build 3 4 0 Beta version only oBRWND ONO Added the ability for the user to import synchronize and playback video files Requires configuration file update Improved Trackvision interface Requires configuration file update Added support for EFI Technology VNET interface module Added various fuel level sender options to USM sensor drop down menu Added the ability for the user to select the path to the weather station data file if the file cannot be found automatically Added CG_NITROUS canparm file Added dash image files for PROII data logger Added sensor type for Haltech module to allow user to change units to PSI and Deg F Build 3 4 1 03 30 2009 Release version 1 Added support for Sportsman data logger Build 3 5 0 05 18 2009 1 2 3 Added utility to calculate custom user calibration tables for USM Added 10 180 ohm resistive pressure sender sensor types to USM Fixed issue in G2X Pro and V300SD canparm files that could ca
10. r 11 The File gt Open dialog box now defaults to the last successful File gt Open folder instead of the RacepakData folder Build 3 7 1 04 27 2010 1 Fixed issue could corrupt GPS longitude when GPS speed was 0 00 2 Fixed issue with Save As function that was introduced in v3 7 0 Build 3 7 2 07 09 2010 1 Fixed issue that was causing incorrect graph avg min max and avg time values when zooming 2 Fixed issue with incorrect math channel calculations when using attached channels 3 Fixed issue that was causing the graph area to not refresh after right clicking on a channel button and then clicking the Cancel button 4 Added support for MoTeC RS232 interface module Build 3 7 3 10 18 2010 1 Added support for Wolf V500 ECU 2 Added support for Hyperkontrol boost controller interface Build 3 7 4 11 29 2010 1 Added support for MSD 7730 ignition interface 2 Extended Haltech write delay time Build 3 7 5 12 29 2010 1 Added and updated canparm files for PRO III data logger Build 3 8 0 01 28 2011 1 Added canparm file to allow support for new M84 ECU Requires firmware version 13 or higher to be installed in MoTeC VNET interface module Added Step 5 CAN ID for MSD 7730 ignition interface Changed some of the channel button naming strategies when new channels are added Added Smartwire support No online help yet but it will be added in the future Added ability to select between vertical or horizontal scroll bar in chann
11. use the data logger to revert back to factory default settings if using G2X Pro firmware version 53 or V300SD firmware version 18 Added the ability to program the GMT time and speed units in the 1Q3 data logger via DataLink Requires firmware version 12 or higher Added the ability to program the IQ3 to flash the internal shift lights when the shift RPM value is exceeded Requires IQ3 logger and display firmware version 12 or higher Added the ability to program the lap number to display on the IQ3 logger dash Requires firmware version 12 or higher Build 3 5 1 09 04 2009 Added Pro EFI interface module canparm file Fixed error in Haltech canparm file that was setting the incorrect VNET ID when fuel pressure sensor type was selected Fixed error in IQ3 Display canparm file that cause Shift Light Reset Level and Shift Light Reset Time to be swapped if Drag Race Mode was enabled Fixed issue that could cause some channels buttons to not appear when creating a real time telemetry file Text in runlog page comments box now automatically wraps to the beginning of the next line when the text reaches the end Build 3 6 0 11 09 2009 OONOORWD wr SS NS NS NS NS SES NS Added Oil Temp and Exhaust Temp to the Haltech ECU sensor type drop down menu Added support for NHRA user key Added support for EC66 interface module Added support for Hondata interface module Added support for Pro EFI interface module Added support for Omex inter
12. w Topology button 2 Added the ability to disable the configuration file assistant dialog 3 Fixed problem that would not allow the user to change the Vnet ID on the Smartwire switch box 4 Added the ability to dim the 1Q3 backlight from a Vnet channel input value Requires IQ3 firmware version 26 or higher Build 4 4 1 07 15 2014 1 Modified TD_STRAIN MOD and TD_STRAIN_MOD_P3 canparm files Build 4 4 2 08 12 2014 1 Added two new CanlD s Converter Pressure 0x399 and Traction Control 0x39A in CanlD canset file 2 Fixed errors duplicated sensor numbers in TD_5V_MOD canparm and TD_5V_MOD_P3 canparm files Build 4 5 0 01 6 2015 1 Added support for O_SHIFTLIGHT_V2 module 2 Added support for Megasquirt_CAN interface module 3 Added support for GPS module 4 Added support for PROIII data loggers to record and display the product information of the MSD 8771 when connected to the VNET bus 5 Added Vnet ID s and scaling for Turbo Wastegate Position module
Download Pdf Manuals
Related Search