Manual - iMIV.ca
Contents
1. In Simple Mode operation the iPod can be controlled by the HU as well as the audio controls on the steering wheel as shown in Table 3 HU button Steering iPod operation Simple Mode Wheel Simple Mode control pl Yes Advances to the next song next track M4 Yes Advances to the revious son prev track i 9 n a Scrolls through the current song in forward fast forward direction n a Scrolls through the current song in reverse rewind direction Table 3 HU control of the iPod in Simple Mode 3 2 4 Advanced Mode In the Advanced Mode the iPod is locked and displays the iMIV Volvo logo the iPod cannot be manually operated All iPod control is accomplished by using the HU buttons and all relevant information is shown on the HU display The Advanced Mode of the iMIV Volvo adapter is used to access the playlists on your iPod of which up to 99 are supported by the adapter Sensolutions Inc 3 8 Chapter 3 User Manual Sensolutions Inc 3 9 Chapter 3 User Manual 3 2 4 1 View types It is important to understand the purpose of the CD and TRK numbers in Advanced Mode The CD portion on the HU screen will always be either or whilst the TRK portion will vary from to RW indicates that the number displayed after TRK is the Playlist number this is the Playlist View RL indicates that the number displayed after TRK is the current Song this is call2. Manual Version 0 95 1 won Content Introduction q1 Main Setup Installation Manual User Manual 3 1 Getting st 1 iPod operation 1 2 AUX input operation 3 2 iPod operation 3 2 1 HU display 3 2 2 Connect disconnect your iPo 3 2 3 Simple Mode gt 3 2 4 Advanced Mode 3 9 3 2 5 Switching between Simple Mode and Advanced Mode 3 20 3 2 6 Resuming 3 21 3 2 7 Ignition on off 3 23 3 3 Service mode 3 24 3 3 1 Setting the adapter in Service Mode 3 24 3 3 2 Uploading Firmware 3 25 3 3 3 Displaying service information 3 28 3 3 4 Emergency procedure for uploading W w w w w w w w y a NN OAD SSA DH firmware we 8 29 3 4 AUX operation 3 83 3 5 VIDEO operation 3 35 3 5 1 RTI and video signal 23 87 3 5 2 Steering wheel controls and TV channel 3 39 3 5 3 iPod Video version ccec eee 3 40 Warranty Disclaimer Liability and Trademarks 4 1 4 1 Warranty i 4 2 Disclaimer and Liability 4 3 Trademarks Appendix A Compatibility Appendix B Troubleshooting Manual Version 0 95 Date October 15th 2006 1 Introduction Thank you for purchasing the iMIV Volvo adapter By reading this manual and using the adapter you ll soon THIS PAGE IS LEFT INTENTIONALLY BLANK find that this adapter has the most feature rich and multi purpose functionality of any available adapter The iMIV Volvo takes full advantage of the exten
3. lt xlxpx x lt lt lt lt 1 The TV channel is available and fully operational but it won t show up in the device list on the HU v available unknown to be determined x not available iPod compatibility All iPods that feature a dock connector can be connected to the adapter The following iPods with dock connector are compatible with the iMIV Volvo adapter e iPod 3G firmware 2 3 e iPod 4G firmware 3 0 2 and beyond e iPod Photo firmware 1 1 and beyond e iPod Mini firmware 1 3 and beyond e iPod Nano all firmwares e iPod Video 5G all firmwares Sensolutions Inc 1 Chapter 4 Sensolutions Inc 2 Chapter 4 Users Manual Users Manual Appendix B Troubleshooting Use the Symptoms Guide to locate your problem and work through the possible problems in the correct order using the Troubleshooting Guide Symptoms Guide 5 Adapter failure 2 3 No video Possible problems 1 Video failure 2 6 2 iPod failure 2 4 3 Firmware failure 2 2 4 Power failure 2 1 5 Adapter failure 2 3 CD ERROR no HU channels or MD ERROR or TV ERROR Possible problems 1 Power failure 2 1 2 Firmware failure 2 2 3 Adapter failure 2 3 Whining noise from engine distorted audio Possible problems 1 Audio interference 2 7 2 Adapter failure 2 3 Troubleshooting guide It
4. RCA audio input connectors on the adapter and the external audio source will now be heard on your car audio system Using special iPod Video firmware Pressing the TRK Change buttons lt lt gt gt on the HU while the TV channel is selected will change between the two AUDIO VIDEO source inputs and R DR enables the iPod video input and enables the external AUDIO VIDEO input RCA connectors on the adapter IM disconnects the video output of the adapter from the RTI system and only the audio will be heard This is true for both TV channels see also section 3 5 1 A video signal from the iPod can only be viewed if the iPod has video capability iPod Photo iPod Video and the video output of the iPod is enabled If you want to display video on the RTI screen the iPod s video output needs to be set to PAL See your iPod manual for further details Further the special iPod Video firmware has to be uploaded to the adapter for high quality audio and video from the iPod Now if you have RTI present in your car and the TV channel is set to B or RWB the RTI screen will raise and the video signal is shown on the screen Note that when the car is moving the video signal will be switched off automatically for your safety If you want to use the video capabilities of your iPod you need to upload the special iPod Video firmware to the iMIV Volvo adapter This firmware will give you high quality video and audio signals from t
5. at least 30 seconds or until the indication LED is switched off Pull the jumper from position 1 and re insert it in position 2 11 Turn on the ignition and check if everything works as expected If the additional HU channels do not show up something went wrong with the upload and the adapter fails to operate normally Re engage the emergency procedure to restore correct firmware to the adapter Sensolutions Inc 3 32 Chapter 3 User Manual 3 4 AUX operation The iMIV Volvo adapter is capable of connecting an external audio source which is available on a separate HU channel The audio source is connected to the adapter via two RCA audio connectors see Figure 14 Your adapter comes pre installed with firmware where the AUX input is available on the TV channel of the HU Since this default firmware also supports the iPod Video two aux video inputs are available utilized via I and GMM selects the iPod as audio video input and A selects the external audio video source available via the RCA connectors as input The input that has been selected is remembered even when the adapter is switched off and can be selected by using the lt lt and gt gt buttons or the steering wheel controls See also section 3 5 The AUX channel is available on two other channels besides TV which are CD CHGR or MD CHGR by downloading another firmware version into the adapter The AUX channel is always different from the i
6. correct firmware Therefore an emergency procedure is provided to be able to get a working adapter always To execute the emergency procedure the jumper location marked as prg on the side of the adapter next to the indication LED needs to be reached Pull the jumper from its position marked as 2 Re insert the jumper at position 1 see Figure 13 Figure 13 Insert the jumper at position 1 to execute the emergency upload procedure The emergency procedure steps are explained below Read through the steps first so you ll know what steps to take on forehand Upload the firmware file to your iPod 1 Create a Genre in iTunes named as _vol_iMIV You can use a different name if you like 2 Add the desired firmware file to your iTunes music library assign it to the Genre created in step 1 and sync your iPod with iTunes Upload the firmware file to the adapter 3 Turn off the ignition and wait for at least 30 seconds or until the indication LED is switched off 4 Set the jumper on the side of the adapter marked as prg to position 1 5 Connect your iPod pause the iPod and navigate to the firmware sound file on your iPod but don t start playing it yet 6 Turn on the ignition The indication LED on the adapter lights red 7 Wait approximately 2 seconds The adapter starts up in firmware upload mode as if normal firmware uploading had been activated via the HU and i
7. correctly and should not be wired to a switched power source However the adapter will never drain your car s battery because it is designed to shut down automatically after approximately 20 seconds Before you connect to battery power turn off ignition to position and disconnect the ground terminal on the battery Once you have made the power connection s for the iMIV turn the ignition key to position Il and connect the battery ground terminal Important Failure to follow this procedure may cause a trouble code which would require a dealer visit to reset Use the provided power connector to connect the adapter to a non switched 12V power source The red wire is hot 12Volt and the green wire is the ground The green wire can be connected directly to the chassis or any good ground point Make sure that secure contact Sensolutions Inc 2 7 Chapter 2 Installation Manual is made by scratching the paint under the contact point if necessary Now connect the power connector to the iMIV Volvo adapter as shown in Figure 5 08 Ground or chassis 12 Volt constant battery Figure 5 Connect constant battery power g ia If any interference e g high pitched engine Tip noise is heard in the audio signal it is most likely due to a ground loop situation Though the adapter is designed to avoid audio ground loops they may occur in rare situations In this case choosing another grounding poin
8. is synced with iTunes the firmware file s can be located easily To execute firmware uploading read through the following steps first so you ll know what steps to take on forehand Sensolutions Inc 3 25 Chapter 3 User Manual Upload the firmware file to your iPod 1 Create a Genre in iTunes named as _vol_iMIV You can use a different name if you like Add the desired firmware file to your iTunes music library assign it to the Genre created in step 1 and sync your iPod with iTunes Upload the firmware file to the adapter 3 4 Turn down the volume of your HU Pause the iPod and navigate to the firmware sound file on your iPod but don t start playing it yet Set the adapter in Service Mode see 3 3 1 Now push the gt gt knob on the HU once and wait approximately 2 seconds The indication LED on the adapter lights red The indication LED starts blinking red green after approximately 2 seconds and the adapter is now ready to receive new firmware Note that the adapter has stopped charging the iPod Also the adapter loses communication with the HU This results in an error being displayed on the HU like CD ERROR This is normal behavior Make sure that these indications are present otherwise repeat step 3 Start playing the firmware sound file on your iPod The adapter expects the firmware sound file to be started within approximately 30 seconds The indication LE
9. long as the adapter is powered ignition on The iPod power up with a cold boot if it has not been on for a longer time or has an empty battery This means the iPod startup takes a longer time and the Apple logo is displayed on the iPod During a cold boot of the iPod the iMIV Volvo adapter is not able to resume the last Sensolutions Inc 3 6 Chapter 3 User Manual Sensolutions Inc 3 7 Chapter 3 User Manual playing situation After the cold boot the adapter will operate in Simple Mode After the iPod is disconnected the display will show again independent of whichever mode the adapter was operating in 3 2 3 Simple Mode In Simple Mode the iPod can 4 be controlled manually as you would normally do As soon as the iPod channel is selected on the HU using the source knob the iPod starts playing and then pauses when the channel is deselected The iPod will also pause if the HU is interrupted e g by a telephone call if you have telephone mute or the integrated carphone hands free kit installed or by a traffic announcement via the radio if TP has been enabled Once the interruption is finished the iPod resumes playing Always connect the iPod to the adapter important when the iPod is paused The adapter expects this and will otherwise reverse the Play Pause operation 1 Some iPod s require to have the Play button pushed manually after a cold start
10. prepaid If Sensolutions is unable to repair or replace the defective product it will issue a refund at a fair market value Warranty does not cover normal tear and wear damages due to negligence improper installation or operation Warranty is void if opened The maximum liability of Sensolutions under this warranty is limited to the purchase price of the product covered by the warranty Prior to returning any defective product you must obtain a Returns Materials Authorization RMA number from Sensolutions All defective products should be returned to Sensolutions with shipping charges prepaid Sensolutions will not accept collect shipments Sensolutions Inc 4 1 Chapter 4 Users Manual Sensolutions Inc 4 2 Chapter 4 Users Manual 4 2 Disclaimer and Liability The iMIV adapter s design and specifications are subject to change without notice Future firmware updates for your iPod may affect the features and functions described in this manual In general the iPod has not been designed to withstand temperature extremes in automobiles Consult the iPod s Owner Manual regarding acceptable operation and storage temperatures Display of artist and song title information on your HU HeadUnit display is not supported Searching the iPod by trackname artist song title album or genre via the HU is not supported Sensolutions is not liable for any incidental consequential or indirect damages
11. replaced or repaired 2 4 Adapter related iPod Check if the iPod cable is connected failure correctly to the adapter and to the iPod Sensolutions Inc 3 Appendix B Troubleshooting Sensolutions Inc 4 Appendix B Troubleshooting adapter s Melbus connector Replace the Melbus cable from the adapter to the HU and check if it fixes the problem 2 6 Video failure Verify that your adapters firmware supports video signals i e it must have the TV channel configured for AUX Make sure that the HU s TV channel is active and set to either TV1 or TV2 Don t drive the car TV1 related If using TV1 check that the iPod is properly connected to the adapter and has been set to the required video settings see section 3 5 3 Make sure that the iPod plays a video file If RTI is used to display video check if the special video cable from adapter to RTI is installed correctly If an external TFT panel is used to display video check if the panel accepts a video input signal directly TV2 related If using TV2 check if the external video source is properly connected to the yellow RCA video input on the adapter with the correct cable and that it generates a video signal If RTI is used to display video check if the special video cable from adapter to RTI is installed correctly and check if the external video source generates a PAL based video signal If an ex
12. the adapter Check if connecting the Melbus cable directly from adapter to HU without connecting ANY other Melbus devices solves your problem If it does your problem is not adapter related but is either a defective Melbus cable somewhere in the setup or a defective Melbus device Have your audio system checked by a Volvo dealer or replace the Melbus cables in your setup one by one to fix the problem Sensolutions Inc 7 Appendix B Troubleshooting
13. up correctly Scroll to the Videos Video Settings menu on your iPod Video Now set the TV Out option to On and set the TV Signal option to PAL if the RTI screen is used for video If an external TFT is used to display video either PAL or NTSC can be used for the TV Signal setting depending on whether the video input signal setting of the TFT panel supports it Sensolutions Inc 3 40 Chapter 3 User Manual Sensolutions Inc 3 41 Chapter 3 User Manual 4 Warranty Disclaimer Liability and Trademarks 4 1 Warranty Please retain the receipt as proof of purchase and write down the information below in case you need to obtain support information Sensolutions Product Date of Purchase Serial Number Invoice Number and or Dealer The Sensolutions iMIV carries a one year limited warranty that protects you from defects in material and workmanship We do not warrant any installation Should a product fail to perform as described above within the warranted period it will be repaired or replaced with the same functionally equivalent product by Sensolutions at its discretion free of charge provided you 1 Return the failed product to a Sensolutions designated repair facility with shipping charges pre paid and 2 Provide Sensolutions with proof of the original date of purchase Repaired or replacement products will be returned to you with shipping charges
14. 1 On The Go 2 On The Go 3 On The Go 4 This particular list would be enumerated by the iMIV Volvo adapter using the index numbers from the playlist names because the first playlist name meets the requirements Scrolling through the playlists on the HU will show Note that the On The Go playlists are not enumerated because their name does not begin with two numbers the enumeration stopped at On The Go 1 Now if you would change the first playlist to 1 Miscellaneous pop music the iMIV Volvo adapter will not enumerate the playlists using the index number from the name because the first playlist name does not begin Sensolutions Inc 3 14 Chapter 3 User Manual with two numbers it should have been 01 instead Scrolling through the playlists will now show a es bad Note that all playlists are now enumerated including the On The Go playlists 3 2 4 3 Using playlists and Songs Playlist and Song access During normal operation when the iPod plays songs the Song View is active and the HU display represents the current playing Song no For example 02 TRK13 shows that Song No 13 of the selected Playlist is playing currently As soon as the next Song starts playing the HU display will update the Song number accordingly Selecting Songs You can search through the Songs using the HU buttons when the Song View is active The HU display will immediately upda
15. 3 1 2 Push the lt lt knob on the HU once 3 The iPod is locked and the service information appears on the iPod s screen Sensolutions Inc 3 28 Chapter 3 User Manual 4 To unlock the iPod disconnect and reconnect the iPod from the adapter The format of the service information on the iPod s screen is cccccc vxx xx xx which is shown in Figure 12 iPod goot 00 00 Serial Firmware number revision OK to disconnect Figure 12 Service information on the iPod display The first six characters c represent the adapter s serial number Beyond the slash the adapters firmware revision number is displayed with a preceding v character For example serial number 0 and firmware revision 01 00 00 would be displayed as 000000 v01 00 00 3 3 4 Emergency procedure for uploading firmware In rare occasions uploading firmware may have been unsuccessful for any reason causing corrupted firmware of the adapter and failure of its operation The most likely reason is that the transfer of the sound file has been interrupted e g because the iPod was paused accidentally or the iPod lacked enough power to play for a few minutes or the cables introduced some kind of unacceptable electrical noise Sensolutions Inc 3 29 Chapter 3 User Manual Because the adapter won t operate anymore with corrupted firmware it is no longer possible to enter Service Mode via the HU buttons and upload
16. D remains blinking red green during this time to indicate that a firmware file can be started If the adapter does not recognize a valid firmware file or the file has not been started Sensolutions Inc 3 26 Chapter 3 User Manual during the blinking of the indication LED it breaks off the procedure without uploading firmware and returns to normal operation The indication LED will light green and the iPod gets charged again 8 Uploading has started and the indication LED lights red constantly with a short green flash every 2 seconds The uploading will take a few minutes to finish A beeping crackling noise is heard on the audio system You can select another channel or turn down the volume completely t is very important NOT to pause the iPod during uploading this results in corrupted firmware and causes the adapter to fail Once the sound file has finished playing the indication LED flashes green 4 times shortly to indicate a successful upload The adapter returns to normal operation with a green indication LED and the HU reflects the changes after a few seconds 9 Turn off the ignition and wait for at least 30 seconds or until the indication LED is switched off Turn on the ignition and check if everything works as expected If the expected HU channels do not show up at all something went wrong with the upload and the adapter fails to operate normally Refer to the emergency procedure see section 3 3 4 to resto
17. Disc knob but the 1 6 preset knobs instead When Advanced Mode has been activated the iMIV Volvo adapter initializes the Advanced Mode and the iPod gets locked and displays the iMIV Volvo logo This will take a few seconds Next the Advanced Mode starts in Playlist View with CD01 blinking The desired Playlist can now be selected Advanced Mode gt Simple Mode Switching from Advanced Mode to Simple Mode is accomplished by first searching through the Playlists as described earlier see section 3 2 4 3 Simple Mode is regarded as an extra Playlist which is positioned between the last and first indexed Playlist For example if you have 3 Playlists that have been enumerated as 01 02 03 searching through the Playlists in forward direction is presented as illustrated in Figure 11 la Ee GR E _ _ _ __ Figure 11 searching through Playlists includes Simple Mode The indication for Simple Mode is shown after the last indexed Playlist After the Simple Mode indication searching starts at the first Playlist again Searching through the Playlists backwards is the same but then in reverse direction Simple Mode becomes effectuated after a few seconds which is the same as with a normal Playlist switch when the CD indication stops blinking Next the iPod pauses the iPod s display will be unlocked and the iPod starts playing again after a few seconds at the current Song 3 2 6 Resuming The ada
18. Nor can we be held liable for warranties that are voided because of the use of this adapter In case of erratic behavior of your car s electrical system please disconnect your iMIV first and have it checked by your installer Sensolutions assumes no liability for any diagnostic fees The maximum liability of Sensolutions under its warranty is limited to the purchase price of the product covered by the warranty Sensolutions Inc 4 3 Chapter 4 Users Manual 4 3 Trademarks e iPod iPod mini iPod Photo iPod Nano iPod Video and iTunes are registered trademarks of Apple Computer Inc e Volvo is a registered trademark of Volvo Trademark Holding AB and or Volvo Cars e Sensolutions is not affiliated with AB Volvo Volvo Car Corporation Volvo Cars or any other Volvo companies Sensolutions Inc 4 4 Chapter 4 Users Manual Appendix A Compatibility iPods without a dock connector 1G and 2G can also be connected The AUX input of the adapter is used to HU compatibility chart connect the iPod to the RCA inputs with an audio cable S80 99 05 IHU 850 IS60 V70 XC70 99 06 HU 650 HU 450 HU 803 HU 603 613 HU 403 413 HU 801 HU 601 611 HU 401 411 IS40 V40 01 04 HU 655 HU 555 HU 1205 HU 605 HU 615 HU 405 HU 415 HU 105 x Spe sc lt c cfclcfcls clc lt isfcis c c c c c cfc sfcls cls x lt sfc cs s xPx sts cdc s lt
19. Pod channel See also Table 2 and Appendix A for possible combinations of channel configurations on your HU If the AUX input is configured as the CD CHGR channel the HU will display CD01 TEKOT constantly Pressing buttons on the HU will not affect the display If the AUX input is configured as the MD CHGR channel the HU will display MDOT TAKOT constantly Pressing buttons on the HU will not affect the display Sensolutions Inc 3 33 Chapter 3 User Manual If the AUX input is configured as the TV channel the HU displays or MM in case the special iPod Video firmware is not used see section 3 5 3 for use with iPod Video firmware Pressing the lt lt gt gt buttons on the HU will toggle between TV 0 and Gi connects the video output to the RTI and Gl disconnects the video output from the RTI see section 3 5 1 In both cases the RCA audio connectors on the adapter are selected as audio source 1 Some HU models display TV 0 while other models display TV without the 0 indication Sensolutions Inc 3 34 Chapter 3 User Manual 3 5 VIDEO operation The iMIV Volvo adapter is designed to support video signals as well Two video sources are available one that is integrated in the iPod cable for video signals coming from the iPod and one that is available via the yellow RCA input connector on the adapter see Figure 14 The video output signal is available on the green RCA co
20. U and switch to another channel With the navigation system switched on the screen switches from video to navigation automatically With the navigation system switched off the screen lowers and turns black Temporarily turning off the video signal Selecting PMY by using either lt lt gt gt buttons or steering wheel controls disconnects the video signal from the RTI unit With the navigation system switched on the screen no longer switches to video automatically if the car stops but navigation remains visible as if you had not selected the TV channel This feature is for your convenience when e g you drive in a unknown city and need the navigation all the time but do not want to deselect the TV channel Sensolutions Inc 3 38 Chapter 3 User Manual External TFT without RTI The video output is available all the time on the TV channel if you have a separate TFT LCD screen connected and have no RTI unit installed in your car whether the car drives or not 3 5 2 Steering wheel controls and TV channel It is possible to use the steering wheel controls while operating the TV channel Using either direction of the steering wheel control always results in a change in forward direction of the selected TV source as if the gt gt button was pressed Sensolutions Inc 3 39 Chapter 3 User Manual 3 5 3 iPod Video version A special firmware is created to fully support iPods with a video o
21. accordingly Basically the iPod needs to be in the same playing situation i e no Song change and no updates as it was when it was disconnected or when the adapter lost its power ignition off Advanced Mode cannot be resumed if one of the criteria doesn t match and the adapter switches to Simple Mode automatically In Simple Mode the iPod starts playing at the currently selected Song Sensolutions Inc 3 22 Chapter 3 User Manual 3 2 7 Ignition on off The adapter is powered on and the indication LED lights green when ignition is switched on The adapter charges the iPod immediately if it is connected Next the adapter tries to resume the last playing situation see section 3 2 6 When ignition is switched off the adapter remains powered for approximately 15 20 seconds before it shuts down completely and switches off the indication LED Your car s battery is never drained because the adapter won t use power when the ignition is off The iPod pauses as soon as the ignition is switched off if it was playing The adapter will continue to charge the iPod for about 6 seconds and then the adapter switches off and stops charging the iPod In Advanced Mode the adapter unlocks the iPod display at the same time the power is switched off to the iPod i e after about 6 seconds By doing so the iPod can always be operated when it is disconnected regardless of the Mode that had been active and regardless of the
22. ack playlist and shuffle mode All information below is based upon the CD CHGR being the iPod channel If you use the MD CHGR as iPod channel instead please substitute the CD indication with an MD indication The described functions are fully transparent on either the CD CHGR or MD CHGR channel Important 3 2 1 HU display The HU displays valuable information about the two modes of operation The adapter has been designed in such a way that you can see at once what your current mode of operation is When the adapter operates in Simple Mode the HU display will always show CEMEC 0 EEMETA soe also Figure 8 The exact indication depends on your HU model When the adapter operates in Advanced Mode the CD number indicates either the iPod s current Playlist or the iPod s current Song while the TRK number indicates the actual Playlist or Song number see Table 4 3 2 2 Connect disconnect your iPod This section assumes you have selected the iPod channel on your HU When there is no iPod connected to the adapter the HU display will always show GROSS see also Figure 7 When your iPod is connected the iMIV Volvo adapter will always try to resume in the play mode it was last operated in see section 3 2 6 for resuming that is either Simple Mode or Advanced Mode In either mode the iPod will always start playing automatically after a delay of a few seconds The iPod when connected will charge as
23. adapter being powered or not Sensolutions Inc 3 23 Chapter 3 User Manual 3 3 Service mode The iMIV Volvo adapter is designed with a special Service Mode feature The Service Mode allows for firmware uploading and showing specific service information To set the adapter in Service Mode it is unnecessary to remove the adapter from it s location It only takes a special button sequence on the HU to enable Service Mode The adapter also features an emergency procedure to upload the firmware even if the former upload failed and caused disfunction of the adapter It is never required to send the adapter to Sensolutions for a firmware upgrade 3 3 1 Setting the adapter in Service Mode A special sequence is required to set the adapter in Service Mode 1 Make sure the adapter is operating ignition on and turn on the HU 2 Connect your iPod to the adapter 3 Select your iPod channel on the HU CD C or MD C 4 Set the adapter to Simple Mode see section 3 2 5 5 a HU s with the rotary 1 20 Dise knob Service Mode is entered by turning the 1 20 Disc knob 10 clicks counterclockwise b HU s with 1 6 disc knobs Service Mode is entered by pushing preset knob 2 10 times 6 The button that is pressed next executes a certain service request If however the iPod responds in a normal fashion when pressing the button you need to repeat step 5 Sensolutions Inc 3 24 Chapter 3 User Manu
24. al In Service Mode two additional buttons can be used step 6 to select either firmware uploading or displaying service information which are explained below Any other button will leave the Service Mode and returns to normal operation of the adapter It is important to perform all the steps accurately For example pressing turning the knob 9 or 11 times will not enable Service Mode 3 3 2 Uploading Firmware The iMIV Volvo adapter features a sophisticated method to upload new firmware into the adapter s flash memory By simply playing a sound file on the iPod the adapter has new firmware installed Other firmware is needed when you would like to change the channel configuration on the HU and assign different channels to the iPod or AUX input It is highly recommended to upgrade the firmware when a new firmware release becomes available Before firmware uploading can be commenced the firmware sound file needs to be uploaded to your iPod Please check www sensolutions com for available firmware releases After selecting and downloading the appropriate firmware file it has to be transferred to the iPod using iTunes It is recommended to place the firmware sound file s in a unique Music library location in iTunes so the file is isolated from the rest of your music collection and can be easily found and selected For example create a new Genre named as _vol_iMIV and place the firmware sound file s in there When the iPod
25. dapter and that the remaining devices e g RTI CD Changer etc be attached to the adapter via its Melbus connector see Figure 3 Best results are achieved when the adapter is first in the chain Use official Melbus cables from Volvo or the included Melbus cable only Installation step 3 Installing the iPod cable The iPod to iMIV Volvo adapter cable provided in the package is the only cable needed to connect the iPod to the adapter This cable provides power for the iPod and carries the audio video and control signals Important Using a non iMIV Volvo iPod cable will result in poor sound and video quality and could cause other problems possibly even damaging your iPod or the adapter Using a non iMIV Volvo iPod cable will void your warranty Run the cable from the desired iPod location to the adapter and connect it to the iPod connector of the adapter see Figure 4 To Pod Figure 4 Connect iPod cable Sensolutions Inc 2 5 Chapter 2 Installation Manual Sensolutions Inc 2 6 Chapter 2 Installation Manual An optional cradle is available from Sensolutions to hold your iPod and keep it in a convenient reachable position If you have purchased this cradle refer to its installation instructions for attaching the iPod connector to the cradle Installation step 4 Connecting the adapter to battery power The adapter needs constant battery power to operate
26. details e g what playlist with index No 33 was about To remedy this a second method of enumerating playlists has been designed into the iMIV Volvo adapter This will help you better organize your playlists better and when scrolling locate them faster on the HU display Instead of using an automatic enumeration where the index number is increased by one for each successive playlist the first part of the playlist name is used for the index number of the playlist When the playlist enumeration starts the iMIV Volvo adapter always checks the name of the first playlist If the first two characters of this playlist name are numbers then the playlist is not assigned to index No 1 but to the index number that is formed by the first two numbers in the name This index will show on the HU as Playlist number For example if your first playlist is named 28 Pop classics then it is displayed on the HU as If the first two characters of the playlist name had not been numbers it would have displayed as EM E A few rules apply to use this type of enumeration Sensolutions Inc 3 11 Chapter 3 User Manual 1 You have to make sure that the first playlist in the list begins with two numbers This means index number one has to be typed as 01 not 1 Change the names of your playlists accordingly if this is not the case remember the playlists are ordered alphabetically 2 Number 00 as fi
27. dible Volvo audio system and was designed to seamlessly integrate into the factory audio and video components without any of the limitations found in similar products The adapter s main features are listed in Table 1 Seamless Integration into the OEM Volvo audio system e Works with RTI navigation and external CD Changer present e All HU xxx models supported S40 classic V40 S60 V XC70 S80 e User selectable HU channel configuration The iPod can be controlled via CD C OR MD C and VIDEO AUDIO integration through the TV channel e ALL described iPod features controlled via HU Steering wheel controls can be used to select tracks and playlists e Integration of VIDEO and AUDIO utilized via the HU TV channel 1 External CD Changer cannot be used with HU 850 or HU 650 radio Sensolutions Inc 1 1 Chapter 1 Introduction Manual Version 0 95 Date October 15th 2006 Rich adapter functionality e Support for all iPod models iPod 1G iPod 2G iPod 3G iPod mini iPod 4G iPod Photo iPod Nano iPod Video e Two modes of iPod operation controlled via the HU Simple and Advanced Playlist control for up to 99 playlists e External VIDEO input and audio input to connect a DVD player TV tuner rearview camera or a PDA gaming console etc e Supports the iPod Video taking full advantage of the audio AND video capabilities of the iPod e Firmware is upgradable by simple downloads a
28. ed the HU will display CD LOAD CARTRIDGE to indicate that the iPod is not present see Figure 7 Figure 7 HU display when the iPod is not connected If an iPod is connected to the adapter it will start to play automatically once the channel is selected If your iPod is not connected to the adapter do so now Because the adapter has not been used before it will switch to Simple Mode operation as shown in Figure 8 See section 3 2 for detailed explanation of the adapter s iPod modes Figure 8 HU display indicates Simple Mode operation The iPod s display will show that it is connected to an external power source battery icon and will start to play automatically after a few seconds as if the Play button on the iPod has been pressed manually Please refer to section 3 2 for a more detailed explanation of the adapter s iPod modes Dependant on the HU model the display will show CD TRK99 or CD00 TRK99 in Simple Mode operation Sensolutions Inc 3 2 Chapter 3 User Manual Sensolutions Inc 3 3 Chapter 3 User Manual 3 1 2 AUX input operation Use the source knob on the HU to scroll to the channel assigned to the AUX input In our example as shown in Figure 9 this corresponds to the TV channel Figure 9 HU display shows AUX input Note that the iPod will pause when the iPod channel is deselected Now an external audio source can be connected to the
29. ed the Song View The HU display is able to show TRK numbers from to DGGE Therefore if a song number in a Playlist is greater than 100 only the last two digits are visible The aE numbers 100 200 300 etc are or GGL see footnote displayed as View type CD TRK indication indication Adv Mode Adv Mode Playlist View CD01 Indicates the iPod s current Playlist E g indicates that Playlist 15 is currently selected Song View CD02 Indicates the iPod s current Song E g indicates that Song 33 is currently playing Table 4 View types of HU display in Advanced Mode 3 2 4 2 Playlists Standard Enumeration Mode Every time the iPod is connected to the iMIV Volvo adapter its Playlists are enumerated The Playlists of the 1 Some HU s are capable of displaying MEKON to EED Sensolutions Inc 3 10 Chapter 3 User Manual iPod are enumerated in the order of appearance in the iPod Playlists menu alphabetically and which is the same as your iTunes Playlists The first playlist in your list will be enumerated as index No 1 the second will be index No 2 etc up to No 99 Playlists above No 99 are ignored and cannot be accessed in the Advanced Mode The index numbers assigned by the adapter to the playlists will show on the HU display e g the second pist in your iPod Playlists menu will show as Indexed Enumeration Mode With a large Playlists collection it can be hard to remember the
30. em Troubleshooting 2 1 Make sure ignition is switched on and that Power other electrical systems in your car failure operate normally If other electrical systems fail as well your problem is not adapter related and your car will need repair Symptom See Troubleshooting Guide No green indication LED Possible problems 1 Power failure 2 1 2 Firmware failure 2 2 3 Adapter failure 2 3 iPod does not charge Possible problems 1 Power failure 2 1 2 Firmware failure 2 2 3 iPod failure 2 4 4 Adapter failure 2 3 iPod does not respond to controls Possible problems 1 iPod failure 2 4 2 Adapter failure 2 3 No sound Possible problems 1 Audio failure 2 5 2 iPod failure 2 4 3 Firmware failure 2 3 4 Power failure 2 1 Sensolutions Inc 1 Appendix B Troubleshooting Sensolutions Inc 2 Appendix B Troubleshooting Make sure the power connector on the adapter is connected and secured in place Make sure that permanent battery power is applied to the power lines of the power connector from the adapter Check the fuse on the power line and replace if defective Check the Melbus cable from the adapter to the HU and make sure it is connected correctly Replace the Melbus cable from the adapter to the HU and check if it fixes the problem Replace the iPod cable from iPod to adapter and check if it fixes the problem iPod related Check if the iPod charges via the Fi
31. es The adapter connects to the HU using a standard Volvo Melbus cable and connects to other Melbus devices with a standard Melbus cable as well Cars that have existing or pre wired RTI CD CHGR or Satellite cabling can use that cable directly without any change or additional Sensolutions Inc 1 3 Chapter 1 Introduction Manual Version 0 95 Date October 15th 2006 proprietary cables The Melbus cable that is provided in the package can be used to connect your adapter to the existing Volvo audio system The iPod to adapter cable that is included in the package uses a 13 pin DIN connector to connect to the adapter Don t ever confuse this connector with the Melbus 13pin DIN connector which is used by Volvo for wiring through Melbus devices The iPod cable provides audio video and control signals from the iPod to adapter and no additional cables are needed for a fully integrated iPod audio and video solution This cable can be used for all iPods that have a dock connector The iMIV Volvo adapter has an extra AUX in RCA input This input can be used to connect e g a satellite radio PDA additional MP3 player and other devices Furthermore an external video source connected to the yellow RCA connector can be used in conjunction with the AUX input This setup can be used to connect peripherals such as a DVD player PDA carputer game console rear view camera etc The green video output connector on the adap
32. from Song View to Playlist View By turning the 1 20 Disc knob once 1 click clockwise or counterclockwise the Playlist View is activated and the HU displays the current selected Playlist 1 HU s that only have the lt lt and gt gt buttons need to press and hold these buttons to access searching For large interval step release the button as soon as the time information shows up on the HU display Sensolutions Inc 3 16 Chapter 3 User Manual For example if you are listening to Song 22 of a Playlist with index No 7 the adapter operates in Song View and the HU shows TA turning the 1 20 Disc knob once will set the adapter to Playlist View and the HU shows If your HU doesn t have the 1 20 Disc knob but has the 1 6 preset knobs instead you ll have to use preset knob 1 to activate Playlist View The adapter switches back to Song View automatically after a few seconds when Playlist View is active Selecting Playlists Once the current view is Playlist View the playlist can be changed Either the rotary 1 20 Disc knob the lt lt and gt gt knobs or the steering wheel controls may be used to change the playlist 1 20 DISC Use the 1 20 Disc knob to search PUSH MEM hrough the Playlists WY starts blinking to indicate that a new Playlist is currently being selected Turning the knob clockwise advances to the next Playlist and urning the knob counterclockwise advances to the previous Play
33. he back of the RTI unit in the trunk so installation is straightforward and easy see Figure 15 Information about removing the RTI unit in the trunk is not covered in this document and can be found in the Volvo manuals VADIS VIDA or internet http vccs volvocars se accessories ii default asp use keyword RTI Figure 15 Installation of RTI video cable Since the RTI unit is mainly designed for navigation the unit itself determines the precedence of the navigation screen and the connected video signal Navigation Sensolutions Inc 3 36 Chapter 3 User Manual Sensolutions Inc 3 87 Chapter 3 User Manual always has priority over the video signal as explained in the following paragraph Suppose that you have a video source connected to the adapter and have installed the video cable to the RTI Selecting the TV channel Select the TV channel on the HU and set the source to or R With the navigation system switched on the screen switches from navigation to video automatically if the car is not moving The screen switches from video to navigation automatically if the car starts moving with a higher speed than 5mph With the navigation system switched off the screen raises and shows the video if the car is not moving The screen turns black for your safety if the car starts moving with a higher speed than Smph Deselecting the TV channel Deselect the TV channel on the H
34. he iPod Your adapter comes preloaded with this special iPod Video firmware See section 3 3 for further details on firmware upgrading Important om 4 Even if you don t have the RTI system in p your car you can still take advantage of the video capabilities of the iMIV Volvo adapter If you connect a TFT screen with composite video input either NTSC or PAL to the Video output of the adapter you can enjoy video as well E g using an iPod Video you can select movies for the kids to watch while the sound is heard via the audio system Sensolutions Inc 3 4 Chapter 3 User Manual Sensolutions Inc 3 5 Chapter 3 User Manual 3 2 iPod operation The main function of the iMIV Volvo adapter is to offer a versatile interface for your iPod The iMIV Volvo adapter has been designed from a true user experience with maximum flexibility in mind to meet the needs of music and iPod lovers This has resulted in an interface that basically has two modes of operation e Simple Mode e Advanced Mode In Simple Mode the iPod can be fully controlled manually like you would do normally However the HU will show no information of current track playlist or shuffle mode In Advanced Mode the iPod is locked and will show the iMIV Volvo logo The iPod cannot be manually operated In this mode all Playlists up to 99 on the iPod can be accessed by using the HU buttons while the HU will show information of current tr
35. irst song of that Playlist after playing the Sensolutions Inc 3 18 Chapter 3 User Manual last song set the Repeat option to All on your iPod 3 2 4 4 Shuffle Play The Random button RND on the HU is used to toggle the Shuffle play mode of your iPod between Off and Songs Pressing the RND button if the iPod s Shuffle mode is Off sets Shuffle mode to Songs and displays the RANDOM word on the HU screen See Figure 10 Pressing RND again sets the iPod s Shuffle mode back to Off The RANDOM word disappears from the HU screen Figure 10 iPod s Shuffle Songs displayed as RANDOM If the iPod is already set to Shuffle play and Advanced Mode is selected the HU will reflect the mode by displaying the RANDOM word on the screen Sensolutions Inc 3 19 Chapter 3 User Manual 3 2 5 Switching between Simple Mode and Advanced Mode An outstanding feature of the iMIV Volvo adapter is that it can switch between Simple and Advanced Mode on the fly using the HU without touching or disconnecting your iPod This way you ll be able to always listen to your favorite music without any limitations Simple Mode gt Advanced Mode Switching from Simple Mode to Advanced Mode is accomplished by turning the 1 20 Disc knob once 1 click clockwise Press disc knob 1 once to switch from Simple Mode to Advanced Mode if your HU doesn t have the 1 20
36. length The iMIV Volvo adapter may not function correctly in this case Important Here is an example of naming playlists Suppose you have defined the following Playlists in iTunes e Birthday songs for kids Greatest hits of Jazz Miscellaneous pop music Modern classical Mozart s symphonies North Sea Jazz Festival 2000 Number one hits from the 90 s Pop Classics Sing along songs The best of Miles Davis On The Go 1 On The Go 2 On The Go 3 On The Go 4 Suppose you would like to categorize your playlists like this so you can easily choose the music that you want to listen to e Category 1 Pop music e Category 2 Classical music e Category 3 Jazz music e Category 4 Music for the kids Sensolutions Inc 3 13 Chapter 3 User Manual Note that playlist categories do not really exist in iTunes It s only a convenient method to organize the playlists Now if you use playlist index numbers that are grouped by 10 or less to indicate the category your playlists would look like this e 10 Miscellaneous pop music 11 Number one hits from the 90 s 12 Pop Classics 20 Modern classical 21 Mozart s symphonies 30 Greatest hits of Jazz 31 North Sea Jazz Festival 2000 32 The best of Miles Davis 40 Birthday songs for kids 41 Sing along songs On The Go
37. list Use the lt lt and gt gt buttons to search hrough the Playlists aH starts blinking to indicate that a new Playlist is currently being selected The gt gt knob advances to Sensolutions Inc 3 17 Chapter 3 User Manual the next Playlist and the lt lt knob advances to the previous Playlist Use the steering wheel controls to s search through the Playlists Operation is similar to using the lt lt and gt gt ie buttons You can search through the available Playlists by using any of the buttons as long as Qi blinks will continue to blink for a few seconds if you stop scrolling Once the blinking stops the Playlist you have selected becomes the active Playlist and the iPod starts playing the the first Song of the Playlist after a few seconds Note that if you are currently listening to a Song and want to change the Playlist using the 1 20 Disc knob you will need to turn the knob at least two clicks One click to select Playlist View and one click to change to the next or previous Playlist Important Automatic Playlist turnover The iMIV Volvo adapter will turn over automatically to the next indexed Playlist if the current Playlist has reached the end The adapter switches to Simple Mode if the last indexed Playlist has reached the end and the iPod starts playing the first song of all available music g Tip If you want the Playlist to turn over to the pi f
38. nd can easily be performed by the end user without removing the adapter e AUX input for additional audio source available on a separate HU channel e g MD C or TV Table 1 Adapter s main features 1 1 Main Setup The main component of the Volvo audio system is the HeadUnit HU It controls the internal audio devices such as radio cassette CD player as well as the external devices like the CD Changer RTI and Television Each device has its own channel in the HU and the external devices are connected via a proprietary electrical bus system called Melbus All external devices need to connect to this bus in order to operate correctly and to allow control via the HU Once connected the devices become known to the HU and are presented as 1 iPod 1G and 2G can be connected to the AUX input Sensolutions Inc 1 2 Chapter 1 Introduction Manual Version 0 95 Date October 15th 2006 additional channels on the HU display Genuine Volvo devices can be chained together with the appropriate cabling or wiring harness which allows for multiple devices to be connected to the HU The iMIV Volvo adapter is designed to seamlessly integrate into the Melbus and to respect other devices on the bus Figure 1 gives an overview of the main wiring of the adapter yi i ie Figure 1 Main wiring of the iMIV Volvo adapter The iMIV Volvo adapter contains a wiring through Melbus connector to link other devic
39. nnector on the adapter and is active when the HU s TV channel is available and is selected as source Figure 14 RCA connectors The adapter can handle both PAL and NTSC based video signals All video important signals are composite video with 75 Ohm impedance The RTI unit requires a PAL based video signal Sensolutions Inc 3 35 Chapter 3 User Manual On the output video connector of the adapter a video display can be connected This may be a separate TFT LCD screen or if you have RTI in your car a special cable can be purchased to connect the video output to the RTI unit to show video on the built in navigation screen in the dashboard The adapter seamlessly integrates with the RTI raises or lowers the screen when needed and displays the video signal If the special iPod Video firmware has not been uploaded to the adapter only the external video source via the RCA connector is available when selecting the TV channel Refer to the section 3 5 3 to select video from the iPod 3 5 1 RTI and video signal If you have RTI in your car and want to connect the iMIV Volvo adapter to your built in navigation screen first you need to purchase a special video cable This cable connects the video output of the adapter to the RTI unit This cable is available for DVD based RTI units and plugs into the RTI with a special green connector This connector can only be inserted in the correct receptable at t
40. or using the iMIV Volvo adapter It includes topics such as using the iPod and the audio video inputs and related subjects such as firmware uploading Please consult your iPod manual for information about how to use the iPod itself It is not covered in this document 3 1 Getting started Once the adapter is installed as described in the installation manual Chapter 2 it is ready for use Switch on the HU to activate the iMIV Volvo adapter The indication LED on the side of the adapter will light green The HU channel s that you have selected by uploading the corresponding firmware will be highlighted on the HU s display see Figure 6 which shows an example of the HU display with additional highlighted channels Figure 6 Additional channels added by the iMIV Volvo 1 The newer HU models such as HU 650 and HU 850 only highlight the channel once it has been selected with the source knob Sensolutions Inc 2 9 Chapter 2 Installation Manual Sensolutions Inc 3 1 Chapter 3 User Manual If the channels are not highlighted the adapter will not function properly In this case check for the correct wiring and confirm that the adapter is properly powered and that the indication LED on the adapter is green see Appendix B troubleshooting 3 1 1 iPod operation Use the source knob on the HU to scroll to the channel assigned to the iPod CD CHGR as seen in Figure 6 If the iPod is not connect
41. pter will always try to resume the last playing situation of the iPod if the iPod is connected or the iMIV Volvo adapter is powered on with the iPod already connected The actual playing situation is stored in flash memory and therefore preserved when ignition is switched off or when the iPod is disconnected The adapter remembers the last mode of operation and the current playlist and song When the adapter resumes it first checks the last mode of operation Sensolutions Inc 3 20 Chapter 3 User Manual Sensolutions Inc 3 21 Chapter 3 User Manual If the last mode of operation had been Simple Mode the iPod starts playing at the currently selected Song If the last mode of operation had been Advanced Mode the adapter initializes the Advanced Mode and locks the iPod Then the adapter matches the following criteria 1 The index number of the currently selected Playlist on the iPod has to be the same as the stored index number of the Playlist 2 The name of the currently selected Playlist on the iPod has to be the same as the stored name of the Playlist 3 The total number of Songs in the currently selected Playlist on the iPod has to be the same as the stored total number of Songs of the Playlist 4 The index number of the currently selected Song on the iPod has to be the same as the stored index number of the Song If all criteria match the iPod starts playing and the HU shows the information
42. rchased separately to give you the maximum freedom of choice Other connected devices e g RTI or CD Changer will affect your choice for the location of the adapter because a Melbus cable will need to connect the iMIV adapter to those device s as well This is not applicable if you don t have other Melbus devices Sensolutions Inc 2 1 Chapter 2 Installation Manual The iMIV Volvo adapter also needs a power connection to operate and should be closely located to a good permanently battery power source or connection Choose an install location that suits you best and use the included Dual Lock strip to secure the adapter into position Sensolutions Inc 2 2 Chapter 2 Installation Manual Installation Step 2 Connecting the adapter to the HU Connecting the adapter to the HU is straightforward You can use the male male 8 pin DIN Melbus cable see Figure 2 that is provided with the adapter or a pre installed Volvo Melbus cable if you have one Figure 2 Melbus cable If the car is equipped with one or more of these options RTI navigation remote CD changer or Satellite radio a preinstalled Melbus cable is present Cars that are prepared for RTI a CD Changer or Satellite radio also have a pre installed Melbus cable Look for a round 8 pin DIN connector near remote device s intended installation location If you don t have a pre installed Melbus cable you will need to install the cable you
43. re correct firmware to the adapter If your current adapter firmware is configured to only support the AUX channel without any iPod support you ll never be able to connect an iPod and execute the above mentioned steps In this case the iMIV Volvo adapter expects the firmware soundfile on the RCA AUX inputs Sensolutions Inc 3 27 Chapter 3 User Manual The adapter stops charging the iPod once the firmware uploading is enabled Therefore it is critical that the iPod is charged sufficiently since firmware uploading takes a few minutes to finish If the iPod stops in the middle of firmware uploading for any reason the firmware of the adapter is corrupted and the adapter won t operate normally anymore Only the emergency procedure can be used in this case to upload new firmware and have the adapter operational again Important 3 3 3 Displaying service information The iMIV Volvo adapter is able to display service information on the iPod s screen Currently the service information comprises of the adapter s serial number and the current firmware revision number The serial number allows for better tracking of your current adapter model and therefore may be needed as input for service requests The firmware revision number can be used to check if your adapter s firmware is up to date The service information is displayed by following these steps 1 Set the adapter in Service Mode see section 3
44. rewire wall outlet adapter If not your iPod is defective and needs repair Connect a different iPod and check if the problem is solved If a different iPod works correctly with the adapter your iPod is defective and needs repair 2 5 Audio failure Turn up the volume on the HU If there is no sound on the HU s iPod channel check if sound is present on the AUX channel by connecting an audio source to the adapter s RCAs If there is sound on the AUX channel refer to 2 4 iPod failure If there is no sound on the HU s AUX channel check if sound is present on the iPod channel by connecting an iPod If there is sound on the iPod channel make sure that the audio source is connected properly with good quality audio cables and that it produces a line output signal Check if the Melbus cable is connected to the HU Check if the Melbus cable on the adapter that runs to the HU is connected to the connector labeled as HU on the adapter There won t be any sound if the HU Melbus cable is connected to the 2 2 Upload appropriate firmware to the Firmware adapter using the emergency upload failure procedure see section 3 3 4 Make sure that the HU channel configuration of the firmware supports your HU see Appendix A 2 3 If all other steps according to the Adapter Symptoms guide did not solve your failure problem contact Sensolutions to have the adapter and or cables
45. rself You can have this done Sensolutions Inc 2 3 Chapter 2 Installation Manual by a local Volvo dealer or a car stereo installation company The iMIV Volvo adapter is connected to the 8 pin DIN connector on the back of the HU with the included Melbus cable Depending on the car and the HU model removing the head unit can be somewhat challenging and require some technical skill This manual will not explain how to remove the HU Information about removing the HU can be found in the Volvo manuals VADIS VIDA or internet http vccs volvocars se accessories ii default asp use keyword IPOD Other good online resources are available on the forums of Volvo enthusiast websites e g http forums swedespeed com Now connect the Melbus cable to the iMIV Volvo adapter by using the adapter s connector labeled as HU as shown in Figure 3 If applicable connect a Melbus cable to the remaining devices e g RTI CD Changer etc by using the adapter s connector labeled as Melbus You may use the Melbus cable included in the package or the existing pre wired cable mainly depending on the location of the adapter To HU COC Etc Figure 3 Connect Melbus cables Sensolutions Inc 2 4 Chapter 2 Installation Manual Important For the highest audio quality it is strongly recommended that the adapter be directly connected to the cars HU via the HU DIN connector on the a
46. rst characters in the Playlist name cannot be used for indexed enumeration because this can be confused with Simple Mode operation If 00 is used standard enumeration applies 3 The enumeration will stop as soon as a playlist name is found where one or both of the first two characters are not numeric It is important to understand that when the first playlist begins with two numbers all successive playlists that do not begin with two numbers will not be enumerated and then cannot be accessed This is different from the first enumeration method where all playlists are enumerated up to 99 This enumeration method is particularly attractive because the index numbers can be designated by the user instead of having them automatically assigned by the adapter Inserting a new playlist half way down the list is now quite convenient because all the other index numbers will be preserved as these are part of the Playlist name Playlists can also be categorized with this enumeration method so they can be remembered and selected easily For example you could make playlist categories by separating the lists into groups of ten or less i e 01 09 10 19 20 29 and so on The name that is assigned to a certain Playlist is not important to the iMIV Volvo adapter as long as it doesn t exceed 50 characters in length Sensolutions Inc 3 12 Chapter 3 User Manual Do not use Playlist names that exceed 50 characters in
47. s ready to receive new firmware The iPod is not being charged The indication LED starts blinking red green after approximately 2 seconds The adapter won t communicate with the HU which results in an error being displayed on the HU like CD ERROR This is normal behavior 8 Start playing the firmware sound file on your iPod The adapter expects the firmware sound file to be started within approximately 30 seconds The indication LED remains blinking red green during this time to indicate that a firmware file can be started If the adapter does not recognize a valid firmware file or the file has not been started during the blinking of the indication LED it breaks off the procedure without uploading firmware and returns to normal operation 9 Uploading has started and the indication LED lights red constantly with a short green flash every 2 seconds The uploading will take a few minutes to finish It is very important NOT to pause the iPod during uploading this results in corrupted firmware and causes the adapter to fail Sensolutions Inc 3 30 Chapter 3 User Manual Sensolutions Inc 3 31 Chapter 3 User Manual Once the sound file has finished playing the indication LED flashes green 4 times shortly to indicate a successful upload The adapter returns to normal operation with a green indication LED and the HU reflects the changes after a few seconds 10 Turn off the ignition and wait for
48. t will solve the problem We recommend using the same ground for the adapter as is used for the HU by tapping into the ground wire of the HU wiring harness If the adapter is not located near the HU use a conveniently located thick Sensolutions Inc 2 8 Chapter 2 Installation Manual grounding cable for the best results Installation step 5 Uploading the appropriate firmware if necessary The iMIV Volvo adapter has pre installed firmware which allows the iPod to be controlled through the HU s CD CHGR channel and the AUDIO VIDEO input to be controlled using the TV channel However other combinations are possible to suit your needs For example if you have a CD Changer already installed and would like to keep it you may choose to control the iPod via the MD CHGR channel see the compatibility chart in Appendix A for your HU s available options Or if you don t have RTI you may want to have the AUX input enabled on the MD CHGR channel See section 3 3 2 for a detailed description on how to change or upgrade your adapter s firmware Now that you ve gone through the installation steps it s time to connect your iPod and the other audio video devices if you have them turn on the car s ignition and enjoy all the features of the iMIV Volvo adapter Please consult the User manual chapter for a detailed description of all features 3 User Manual This User Manual explains all the operational details f
49. te the Song number to the one you have selected The lt lt and gt gt buttons are used to search through the Songs in the Playlist The gt gt knob advances to the next Song Pressing the lt lt knob once will restart the current Song from the beginning Pressing the lt lt knob again immediately advances to the previous Song Sensolutions Inc 3 15 Chapter 3 User Manual The lt lt and gt gt buttons have been defined for two purposes 1 searching in the current song and 2 large interval step search of Songs Pressing the gt gt knob shortly will advance 10 Songs at once forward Pressing the lt lt knob shortly will advance 10 Songs at once back Holding down the gt gt knob for a few seconds will start fast forward searching of the current Song Holding down the lt lt knob for a few seconds will start fast reverse searching of the current Song A short delay follows when searching through the Songs is finished before the Song actually starts playing on the iPod The delay is approximately 0 5 seconds and within this timeframe search buttons can be combined to scroll to your favorite Song fast and convenient For example if your current song is No 11 and you want to scroll to Song No 32 press gt gt twice shortly and immediately press gt gt once after that Changing from Song View to Playlist View 1 20 DISC The 1 20 Disc rotary knob on the HU MEM is used to change
50. ter can be connected to the RTI system or to a separate external TFT display to display video The video input requires a PAL composite video signal if the output is connected to the RTI system The video source can be either PAL or NTSC when the external TFT panel is used and depends on the input signal capabilities of the TFT panel only A special VIDEO out cable can be purchased from Sensolutions that connects the adapter to the RTI This cable together with special adapter firmware which is pre installed allows for two video sources iPod and an external video input to be available on the HU s TV channel and the built in RTI navigation display The iMIV Volvo adapter is designed with the capability to upgrade its firmware while the adapter is installed in the Sensolutions Inc 1 4 Chapter 1 Introduction Manual Version 0 95 Date October 15th 2006 car Changes and updates can be made without removing and sending it back to the manufacturer New features are made easy The firmware is upgraded by initializing a firmware upload sequence and then playing a special music file on the iPod Various firmwares are available that allow different configurations of the iMIV Volvo adapter and the Volvo audio system See section 3 3 2 for further information about upgrading the firmware The iMIV Volvo adapter integrates the iPod and AUX VIDEO inputs each on their own HU channel Table 2 shows the channels that can be
51. ternal TFT panel is used to display video check if the panel accepts the video input signal from the external video source directly General Check if the Melbus cables from the adapter and the RTI unit in the trunk are installed and connected properly 2 7 Audio interference Check if other channels on your HU that are not adapter related like CD player radio tape etc pick up the audio interference like a whining noise If the interference is noticeable on all channels then your problem is not adapter related Have your audio system checked by a Volvo dealer Activate the AUX channel on the HU and disconnect any external audio source from the adapters RCA connectors If the noise is gone then either your external audio source or RCA audio cable causes the interference Replace the audio cable or if that does not help use an audio ground loop isolator to get rid of the interference Replace the iPod cable if the audio interference is present on the iPod channel but not on the AUX channel If that does not solve your problem either your iPod or your adapter is defective Refer to the corresponding troubleshooting guides Sensolutions Inc 5 Appendix B Troubleshooting Sensolutions Inc 6 Appendix B Troubleshooting Check if the Melbus cable on the adapter that runs to the HU is connected properly and inserts into the connector labeled as HU on
52. used for each input iMIV Volvo input HU channel iPod CD CHGR MD CHGR CD CHGR AUX only input no video MD CHGR TV AUDIO VIDEO input TV Table 2 Different HU channels can be used by the iMIV Volvo adapter Each combination of channels is activated by downloading the appropriate firmware For example if the video capabilities of the iMIV Volvo are to be used the TV channel is utilized for both AUDIO input and VIDEO input It is not possible to use the same channel for both the iPod and AUX or AUDIO VIDEO input Sensolutions Inc 1 5 Chapter 1 Introduction 2 Installation Manual The basic installation steps to install the iMIV Volvo involve Choosing a location for the adapter Connecting the adapter to the HU Installing the iPod cable Connecting the adapter to battery power Uploading the appropriate firmware if necessary CeO NOS Installation Step 1 Choosing a location for the adapter The iMIV Volvo adapter can be installed at different locations in your car For example the glove compartment trunk console armrest behind the dashboard or radio or under the front passenger seat are all possible locations Keep in mind that the provided cables are of limited length so the mounting location will also depend on where you intend to keep the iPod It is recommended to first determine where you want the iPod located and then to work from that point on Longer Melbus and iPod cables can be pu
53. utput iPod Photo and especially iPod Video The iMIV Volvo adapter has been designed so that the audio and video capabilities of your iPod can be leveraged into the factory audio system without the need for extra cables or additional hardware The adapter s iPod Video firmware enables a second video input on the TV channel and provides high quality audio and video signals from the iPod Besides video your iPod can still be used as a music player via the CD CHGR or MD CHGR channel as described in previous sections without disconnecting it All features of AUX and Video as described above in previous sections remain unchanged Switching between the A V inputs The TV channel is the only available channel for the external AUDIO VIDEO input on the adapter with the iPod Video version firmware The TV channel can switch between the two AUDIO VIDEO inputs using and switches the iPod AUDIO VIDEO input and DE switches the external AUDIO VIDEO RCA connectors on the adapter as input to connect e g a DVD player rear view camera gaming console etc Temporarily turning off the video signal Besides T and M BD is available as well to disconnect the video signal from the RTI and temporarily turn off the video signal see section 3 5 1 The lt lt knob can be used to switch from to The gt gt knob can be used to switch from to iPod video settings To use the iPod as video source it s video settings need to be set
Download Pdf Manuals
Related Search