Dasher 9
Contents
1. Notes 18 Notes 19 WARRANTY Please refer to warranty information included with unit DISCLAIMER Congratulations on your purchase of the Shoprider Dasher Portable scooter It is not intended to be used by individuals with physical limitations that could prevent the user from operating this unit safely Shoprider disclaims all responsibility for any personal injury or property damage which may occur as a result of improper or unsafe use of its products Mechanical or electrical defects will be dealt with on a contingency liability basis The preceding guidelines are intended to assist you in the safe operation of your powered scooter If you should have any questions about the correct operation of your scooter please contact your authorized Shoprider provider Model Name DASHER 9 Serial No Provider s Stamp Shoprider Mobility Products Inc 800 743 0772 www shoprider com 20 P N 300904 36 A42. ve WEE mm V wA DE EEE WARNINGS 1 Do not operate hand held transceivers transmitters receivers such as citizens band CB radios or turn ON personal communication devices such as cellular phones while the scooter is turned ON N Be aware of nearby transmitters such as radio or TV stations and try to avoid coming close to them If unintended movement or brake release occurs turn scooter OFF as soon as it is safe P Be aware that adding accessories or components or modifying the scooter may make it more susceptible to EMI NOTE There is no easy way to evaluate the overall immunity of the scooter 5 Report all incidents of unintended movement or braking to your Shoprider provider and note whether there are sources of EMI nearby WARNING Shoprider amp is not responsible for damage or injury incurred due to improper and unsafe use of our scooter ADJUSTMENTS 2 adjustment Tiller Angle Adjustment Fig 2 At the base of the tiller is a round knob a Turn the knob counterclockwise to loosen the tiller and select the desired tiller angle Turn the knob clockwise to securely lock the tiller into place Below the knob there is a lock designed to stop the tiller from turning left or right Do not forget to unlock this before driving the scooter NOTE For Safety this lock is designed to break away if the scooter is driven when locked Figure 2 Tiller angle adj
3. Detach rear section from front section Detach lever yellow is located in the rear of the scooter next to the freewheel lever Slide lever to detach and separate rear section from front section Co Figure 10 Figure 11 13 BATTERIES AND BATTERY CHARGING The Shoprider Dasher Portable scooter is supplied with maintenance free sealed lead acid batteries For easy handling the batteries are contained within a battery pack Battery life and performance may be affected by temperature terrain condition of battery the weight of the user and care of batteries The battery needle gauge is only a guide and is most effective when the scooter is moving only then is the true discharge level displayed e When the scooter stops the battery needle gauge may indicate full An active user can use up to 30 of battery capacity or more per day e Inactive users may only use 50 of battery capacity in a week e n both these instances the battery should be put on charge over night Keeping the batteries charged will extend the life of the batteries Battery Charger The battery charger is a 2A or 3A off board The Dasher Portable scooter has a built in charger port on the rear side of the battery pack This special feature allows the batteries within the battery pack to be charged without the scooter A compartment built into the battery pack is designed to store the battery charger when not in use Fi
4. a few minutes To remove from sleep mode turn the key off and back on again Check List If your scooter fails to operate please check the following e Unit is switched on Drive Freewheel mechanism is in the drive position All plugs and connectors are clean and firmly connected e Battery level shows full charge If the free wheel device has been operated with the scooter switched on then the scooter will not operate until the ignition key has been switched off and then on again Please consult your dealer if your scooter does not run after checking these points 15 m ms um ms wn m un UN Aum m AEN 4 M Be A A AT WE Em WE mm BA ED ARBRE w TECHNICAL SPECIFICATIONS UNIT SPECIFICATIONS DASHER 9 Overall Dimensions L x W x H in 38 8 x22 x 36 Front 9 x 1 Flat Free Number Size of Tires Rear 9 x 2 Flat Free Suggested User Weight on the Level Road D MAX a00 Weight of Heaviest Part Ib 35 Battery Pack 21Ah x 2 Total Weight w 21Ah Battery Ib 110 Pack Basket Seat Battery Pack Module Weight Ib 35 V Ah Battery Module Capacity X Pos 12V 21Ah x 2 Charger Amp 2 or 3 Off Board Output Power of Motor hp 0 75 Maximum Speed evel road mph 3 8 Safe Climbing Angle Maximum 10 6 16 9 Single User Weight Refer to fig 9 Ranges per charge w STD 21AH Battery 90 kg User Weight After the mile battery and
5. 11 2 mechanical moving parts fully break in Turning Radius in 31 5 Detachable Chassis Y N Y ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE 1 Include the Anti Tip wheel 2 Driver weight may exceed weight of the unit speed must be reduced when turning 3 The actual driving range varies with the factors shown below a the weight of occupant b ground surface c battery conditions d type of charger e ambient temperature f the way of driving g terrain QUARTERLY INSPECTION For your own safety quarterly inspection and service of the product by an authorized dealer is recommended There may be a nominal dealer inspection fee for this service not covered by warranty Maintenance records below should be kept at all times The manufacturer distributor vendor will be indemnified from any product liability claim if the above maintenance service requirement not met NOTE Regular inspection is recommended by the manufacturer to ensure ultimate performance of the vehicle Service Record Date of Purchase Purchaser Model DASHER 9 Serial Dealer Unit Was Purchased From M DI Y M DI Y M DI Y M DI Y M DI Y M D Y M D Y M DIY M DIY M D Y M DIY M DIY M D Y M DIY M DIY M DI IY M DIY M DIY M DI Y M DIY M DIY M D Y M DIY M DIY M DIY M DI Y M DI Y M DI Y M DIY M D Y M D Y M DIY M DIY M D Y M DIY M DIY 17
6. number is located on the seat post and consists of a combination of 13 numbers and letters Shoprider recommends that you write the serial number down on the back of this manual for future reference Refer to Fig 5 Circuit Breaker Reset Button Free Wheel Lever yellow Charging Port Detach Lever yellow Anti Tip Wheels Figure 8 10 STARTING TO DRIVE YOUR SCOOTER First Time Use Prior to using your Dasher Portable scooter for the first time you must charge the batteries fully refer to Battery Charging Procedures Charging may take up to 12 hours Charging the batteries completely prior to first time use will benefit battery efficiency Failure to do so may cause permanent damage Getting Started e Select a level area with plenty of space e Mount the scooter by pushing the arm upward out of the way and sliding onto the seat or swivel the seat around to mount Use the arm rest for support if necessary e Adjust the tiller and seat as previously described Starting Scooter Movement e Ensure that you are seated in a comfortable position e Turn the key to the on position e Your speed setting should be on or near the turtle slow e Push your right thumb lever yellow and the scooter will move forward slowly The harder you push the faster the scooter goes but will only reach the speed level that has been selected e Release the lever and the scooter will slowly come to a stop as the magnetic bra
7. Portable Scooter User Manual Fe EZ m WE D d BA ED EEE Table of Contents INTRODUCTION een 3 FEATURE essen aber 3 SAFETY BBVIDE een 4 5 EMI 5 6 7 8 SCOOTER TILLER 8 9 DRIVE FREEWHEEL 10 STARTING TO DRIVE YOUR 11 EXTRA GUIDELINES IN THE CONTROL OF YOUR SCOOTER 12 13 BATTERIES AND BATTERY 14 VINNAN O 15 TROUBLESHOOTING GUIDE eeneeenmeee ene 15 TECHNICAL 16 QUARTERLY INSPECTION 2 2 en 17 NEE WARRANTY AND 20 INTRODUCTION Congratulations on your purchase of the Shoprider Dasher 9 Portable scooter The Dasher is the ultimate combination of style comfort and portability The Dasher comes with three interchangeable colors giving you the choice of a different color every day and includes several innovative and convenient features The Dasher goes with you wherever you go and can be assembled or disassembled in just seconds with wireless quick connect component
8. e by untrained and unauthorized persons e DO NOT connect any medical device to the scooter battery This could cause failure of the device the scooter and personal injury e Make sure the tiller is properly adjusted to the user or damage and injury could result e DO NOT transport in a vehicle WHILE seated on the scooter Shoprider will not be responsible for any injury or damage that might result e DO NOT use the scooter in the rain or near any other water source where the scooter may get wet Direct exposure to rain or dampness could cause damage to the scooter electrical components e For maximum battery life make sure to fully charge batteries for up to 12 hours prior to first use EMI WARNING Shoprider scooters may be susceptible to electromagnetic interference EMI which is a kind of interfering electromagnetic energy EM emitted from sources such as radio stations TV stations amateur radio HAM transmitters two way radio and cellular phones The interference from radio wave sources can cause the scooter to release its brakes move by itself or move in unintended directions It can also permanently damage the scooter s control system The sources of radiated EMI can be broadly classified into three types 1 Hand held portable transceivers transmitters receivers with the antenna mounted directly on the transmitting unit Examples include citizens band CB radios walkie talkie security fire and police t
9. e is automatically operated when the thumb control levers are pressed or released There is a slight delay when the scooter accelerates and decelerates this allows the scooter to start smoothly and come to a smooth stop Battery Level Indicator Gauge On Off 2 Key Switch Horn Button oe nn Thumb Control Reverse Control Forward Figure 7 9 DRIVE FREEWHEEL OPERATION FIG 8 The drive freewheel lever yellow ball handle is located under the seat at the right rear of unit This lever allows you to disengage the drive mechanism and push the scooter while in freewheel mode To disengage the drive mechanism neutral move the lever forward the scooter can now be pushed To re engage the drive mechanism drive move the lever backward now the unit may be driven Note The scooter will not operate while the drive freewheel lever is in the neutral position forward The scooter must be turned off lever moved backward drive position and then turned on in order to reset the circuits WARNING Always re engage the free wheeling device after use Failure to do so may result in injury Anti tip wheels The anti tip wheels are located at the rear of the scooter frame Fig 8 The scooter should not be used unless the anti tipping wheels are in place Shoprider is not responsible for damage or injury incurred due to improper or misuse of the scooter Scooter serial number The scooter serial
10. e there is a safe controlled descent When the thumb levers are released the scooter will slowly stop Safe Climbing Angle Always follow the guidelines of the safe climbing angle as shown in figure 10a Caution Do not turn off the control key while the unit is in motion Grass and Gravel Please follow the guidelines given previously and your scooter will perform admirably over many surfaces Avoid long grass loose gravel and sand NOTE You should not operate your scooter in wet weather or on wet surfaces This may cause the motor to short out or cause other irreversible damage NOTE To preserve battery charge your scooter may go into sleep mode after being idle for a few minutes To remove from sleep mode turn the key off and back again Single user Figure 9 12 TRANSPORT STORAGE The Dasher Portable scooter is designed to be quickly and easily disassembled into sections for transportation and storage Follow these simple guidelines for disassembly Dasher 9 Disassembly Fig 9 amp 10 1 Remove the front basket Lift basket up and off Fold the seat down and remove Pull yellow swivel seat lever up and lift seat up and off Remove battery pack Lift battery pack up and off using handle Note battery pack is secured by Velcro Fold tiller down and lock into place Loosen tiller adjustment knob lower tiller and tighten adjustment knob Lock tiller assembly by pulling yellow lever up and to the right
11. ended on a regular basis e Most lubricated components on the Dasher Portable scooter are designed to be maintenance free and are sealed Therefore lubrication is not required for these components However the driving axles and seat post should always have a very light coat of multipurpose grease DO NOT USE TOO MUCH GREASE Drips may stain or damage carpets furnishings etc e It is recommended that the driving axles inside the drive wheel assembly be checked and cleaned occasionally for hair and debris build up which will hinder the performance of the unit e Check the batteries on a regular basis For extended battery life it is highly recommended that the batteries be fully charged after each use If the batteries are weak severely discharged or old a variety of problems may occur with the unit including charging problems reduced speed loss of range and others Please contact your local Shoprider provider for battery replacement TROUBLESHOOTING GUIDE Circuit Breaker Reset Button Your scooter is fitted with the latest in electronic controls that are programmed to protect the electrical system from abnormal overloads Provided for extra protection is a circuit breaker located on the side of the battery pack Should there be a situation where your scooter stops for no apparent reason please check that the circuit breaker has not popped NOTE To preserve battery charge your scooter may go into sleep mode after being idle for
12. ke automatically engages Steering Steering the scooter is light and easy When starting off ensure that you give a wide clearance when turning so that the rear wheels clear any obstacle that you are passing When steering through limited spaces such as a doorway or when turning around turn the tiller handles where you want to go and apply power gently The scooter will turn very tightly but will still move with complete stability as long as the speed is not too high Reversing Before reversing ensure that the area behind is free from any hazards or obstructions Adjust your speed setting to a low setting before you move in reverse Push your left thumb lever black and steer wide of all corners and obstacles Dismounting Before dismounting ensure that the key is turned to the off position Dismount the scooter by pushing the arm upward out of the way and sliding off the seat or swivel the seat around to dismount Use the arm rest for support if necessary CAUTION Please ensure that care is exercised when mounting or dismounting the scooter and that the tiller and foot rest is not used for support 11 Ramps The stability of your scooter is governed by several factors such as the seating position the angle of the slope and your height and weight When approaching an incline do so directly and not at an angle and where ever possible avoid making turns When going down a ramp or slope keep the speed settings to slow This will ensur
13. ockwise to lock the arm rests into place Armrest Adjustments Fig 6 The arm rests are hinged and can be pulled up and out of the way for sideways transfer Pull arm rest up and back Figure 6 SCOOTER TILLER CONTROLS FIG 7 Speed Controls The speed control allows you to set a speed between slow turtle and fast rabbit Battery Level Indicator Gauge Where the needle sits shows the amount of charge left in your batteries The amount of charge will only show at its true level when the scooter is in drive Always charge the batteries completely before beginning out on any journey Caution Do not allow the gauge needle to go down completely as complete discharge of the batteries could cause irreversible battery damage Horn A yellow button on top of the tiller operates the horn Thumb Lever Controls The left thumb lever controls the reverse and the right thumb lever controls the forward motion The amount of pressure applied to each lever will determine the speed the scooter travels at up to the speed selected Release the thumb lever and the scooter will automatically come to a stop as the electromagnetic brake is applied to the motor On Off Key Switch Insert the key into the key switch located on top of the tiller Turn the key and the battery gauge needle will move There may be a slight delay before the thumb lever control can be operated while the main controller checks the circuits Electromagnetic Brake The brak
14. ransceivers cellular telephones and other personal communication devices NOTE Some cellular telephones and similar devices transmit signals while they are ON even when not being used 2 Medium range mobile transceivers such as those used in police cars fire trucks ambulances and taxis These usually have the antenna mounted on the outside of the vehicle 3 Long range transmitters and transceivers such as commercial broadcast transmitters radio and TV broadcast antenna towers and amateur HAM radios NOTE Other types of hand held devices such as cordless phones laptop computers AM FM radios TV sets CD players and cassette players and small appliances such as electric shavers and hair dryers so far as we know are not likely to cause problems to the scooter Scooter Electromagnetic Interference EMI Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna source the EM fields from hand held radio sources transceivers are of special concern It is possible to unintentionally bring high levels of EM energy very close to the scooter s control system while using these devices This can affect scooter movement and braking Therefore the warnings listed below are recommended to prevent possible interference with the control system of the scooter lt AR me AH A UNS CM NN Em ms um mm mm m mss Am A NEA wm eT CET NA A Be EEE AEE
15. rst Time Use Prior to using your Dasher Portable scooter for the first time you must charge the batteries fully refer to Battery Charging Procedures Charging may take up to 12 hours Charging the batteries completely prior to first time use will benefit battery efficiency Failure to do so may cause damage Charging To charge the batteries plug the A C cord plug into the wall socket and connect the 3 pin male plug lead into the 3 pin female battery charging socket located on the battery pack The battery charger has two indicator lights The red light when solid indicates power The green light will flash when charging and go solid green when the charging cycle is complete If the red light flashes when charger is plugged into charging port of battery pack then there is a problem Please contact your provider or Shoprider for assistance Once the batteries are completely charged unplug the A C cord from the wall then unplug the 3 pin lead from the battery pack WARNING Only use the original Shoprider approved charger This charger is for indoor use only DO NOT expose it to rain or water spray Do not leave the charger plugged into the charger port if the charger is not charging 14 MAINTENANCE Tires Since your tires are flat free tires there is no need to ever worry about tire air pressure General Maintenance and Lubrication e Inspection for loose wheel bolts seat and arm tightening bolts and other nuts and bolts is recomm
16. s The Dasher is super light and compact and can be stored in small areas such as the trunk or back seat of your car The compact features support easy transportation of your Dasher for today s active lifestyle The Dasher can be used in confined spaces both indoors and out Direct drive transaxle and electromagnetic brake give a safe and efficient ride We know that the Dasher portable scooter will provide many years of mobility for you Please ensure that you read this manual carefully it is important for your safety that you understand the guidelines and instructions given SMART FEATURE GUIDE Fig 1 Om Tiller control head Detachable seat with fold down Back with removable pads Flip down arm rests Detachable basket Detachable battery pack Tiller adjustment knob Swivel seat lever and seat release lever Puncture proof tires Anti tip wheels 10 Tiller lock for transport For Safety this lock is designed to break away if the scooter is driven when locked E ds Figure 1 SAFETY ADVICE e DO NOT carry passengers DO NOT exceed inclines over 6 degrees 10 grade DO NOT turn on steep inclines e DO NOT turn suddenly at high speeds e DO NOT get on or off the scooter unless the brake is on and the scooter is switched off e DO NOT switch off the scooter while the scooter is moving e DO NOT drive the scooter where you can not safely or legally walk e DO NOT drive the scoo
17. ter on the road street or highway e DO NOT attempt to drive over curbs greater than 2 inches in height Doing so could cause your scooter to turn over causing injury or damage to the scooter e DO NOT drink or use a mobile phone when driving your scooter e DO NOT exceed the suggested user weight limit Doing so could cause personal injury and invalidate the warranty e ALWAYS keep your feet on the scooter when moving e Consult your doctor if there is any doubt about your ability to use a scooter safely e ALWAYS slow down and proceed carefully when traveling over rough or uneven ground e For individuals with balance problems practice getting on the scooter with assistance of a qualified healthcare professional e DO NOT operate the scooter without anti tip wheels installed e DO NOT use an escalator to move a scooter between floors Serious injury could occur e DO NOT drive the scooter on an incline that has oil water or ice film on it e DO NOT try to lift the scooter by its seat tiller or any removable parts Any of these could cause injury to the user or damage to the scooter e DO NOT use parts or accessories that are not authorized by Shoprider e Before sitting in or exiting the scooter REMOVE the key from the ignition This will insure the POWER is off and the scooter can not move under its own power e As a general precaution always remove the key from the ignition while the scooter is not in use This will prevent us
18. ustment knob Folding the Tiller Fig 3 Fold down the tiller by loosening the tiller angle adjustment knob located at the base of the tiller fig 3 Tighten knob to lock tiller in place You may lock the tiller assembly into place so that it doesn t swing from side to side by lifting the yellow tiller lock lever up and to the right Seat Removal Fig 4 Fold down the back of the seat Lift the swivel seat release handle up to lift the seat up and off the seat post Fold down seat assembly 7 Figure 4 Seat Height Adjustment Fig 5 Remove seat as described fig 4 Remove battery pack refer to disassembly section Using two 13mm wrenches remove locking bolt and nut Adjust seat post up or down to desired position The seat height can be adjusted to five different positions by inserting the locking bolt in the desired hole Replace washer and nut and tighten Replace battery pack and seat Serial Number Fig 5 Serial number is located on the seat post Itison a white sticker with a barcode The serial number is 13 alphanumerical digits beginning with a 1 Figure 5 Armrest Width Adjustments Fig 6 On the underside back of the seat there are two arm rest hand knobs one on each side Turn hand knobs counterclockwise to loosen Loosening the arm rest hand knob allows the armrest width to be adjusted or arm rest to be removed Once the desired positions of the arm rests are set tighten the hand knobs by turning cl
Download Pdf Manuals
Related Search