TRENDnet TVP-224HR Manual
Contents
1. Access Fixed IP Menu 2 Type in IP Address 192 168 1 20 Subnet Mask 255 255 255 0 and Default IP Gateway Address 0 0 0 0 in the related fields 3 Click on Save 4 Click on Reboot Gateway B IP Setup 5 Navigate to Internet Access Fixed IP Menu 6 Type in IP Address 192 168 1 55 Subnet Mask 255 255 255 0 and Default IP Gateway Address 0 0 0 0 in the related fields 7 Click on Save 8 Click on Reboot Gateway A Dial Plan Setup FXS Ports to Analog Phones Gateway A has two phones on the FXS ports Telephone number 203 on Port 2 and 204 on Port 3 These numbers are part of the default dial plan and do not have to be entered We can skip the local Dial Plan setup including Telephone Address hunt group and destination for phones 203 and 204 How to Enter the Dial Plan The Dial plan consists of three tables that include the Telephone Table Hunt Group eg Customer Service may have multiple phones that the GW must search through for an open line and Destination Table Both Local and Remote The dial plan has to be entered into all Gateways so that the local gateway knows how to process calls sending them to its local ports or to remote gateways for further processing The following screen shots show an example for entering a dial plan for a single number This example should give you the necessary insight as to how to enter the rest of the Dial Plan If you still have difficulty understandin2. RS 232 cable connects the console port of the TVP 224HR to a console PC or terminal Task Connect RS 232 Cable to TVP 224HR RS 232 console port a your computer that you will use as a configuring terminal Open HyperTerminal and enter the following Input Parameters when prompted Baud rate Number of data bit Parity check Number of stop bit Flow control When HyperTerminal Screen appears type 123 In the event that you forget your administration password you can gain console access to the TVP 224HR using the super password The super password is the last six digits of your MAC address located on the bottom of your TVP 00 50 2d xx xx xx At the Console prompt enter the super password without hyphens The password is all lower case After gaining access at the console prompt type in net set manager password lt new_password gt lt new_password gt net store net reset If entry of new password is successful the console will list OK You will now be able to gain Web Access from a PC in the same local segment using the TVP 224HR LAN IP Address If Web and or Telnet Access are enabled you will also be able to remote access the TVP 224HR by entering http followed by the TVP 224HR WAN IP or domain name foe At the prompt Console gt Enter ping 168 95 1 1 The following dialogue indicates that Internet Access is successful ping 168 95 1 1 1 out of 1 pings succeeded Console gt ping Consol
3. 8 to 10 digits 2 Digit Taiwan Area Code from GW B 01 is stripped prefix address 9 is dialed to PBX on FXO Port 0 for outside line and then remaining 8 to 10 digits are dialed 22 is stripped and remaining 3 digits are sent to GW B 02 8 to 11 digits 3 Digit US Area Code are sent to GW B This is an example only Please substitute your ext on PBX if applicable This is an example only Please substitute your ext on PBX if applicable For PBX on FXO use only For PBX on FXO use only Remote Zone used to make calls to remote GW B FXS Internal Ext Remote Zone used to make calls to remote GW B FXO Externa PBX PSTN Gateway A Hunt Group Table 3 Loz 2 NOTE The above destination table has both local destinations and remote destinations When the gateways are taken out of this initial testing environment and implemented in the field the internet access settings will have to be updated In addition the above remote destination IP will have to be updated to the field IP address Gateway B Telephone Number Table Prefix Prefix Dialing 203 calls phone Oe T Dialing 204 calls phone outside line 0 Line 1 02 is stripped and the remaining 8 to 11 digits 3 Assumes that Telephone None Digit US Area Code are line is attached to Port dialed out on Port 0 to 0 Line 1 PSTN Dialing 9 from local phone Assumes t
4. ID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT FE CE TRENDn TRENDware USA What s Next in Networking Product Warranty Registration Please take a moment to register your product online Go to TRENDware s website at http www TRENDNET com TRENDnet Technical Support US Canada Support Center European Support Center Contact Contact Telephone 1 310 626 6252 Telephone Fax 1 310 626 6267 Deutsch 49 Email support trendnet com Francais 49 Espa ol 49 0 6331 268 460 Tech Support Hours English ae 0 0 6331 268 461 0 6331 268 462 ifi 0 6331 268 463 aa Pacific Standard Time italano lt 49 0 6331 268 464 Dutch 49 0 6331 268 465 Fax 49 0 6331 268 466 Tech Support Hours 8 00am 6 00pm Middle European Time Monday Friday TRENDware International Inc 3135 Kashiwa Street Torrance CA 90505 http www TRENDNET com Copyright 2005 All Rights Reserved TRENDware International Inc
5. TVP 224HR 4 port VoIP Gateway with 4 port Broadband Router Quick Installation Guide Version 07 25 05 TRENDn 4 TRENDnet TRENDware USA d What s Next in Networking Copyright 2005 All Rights Reserved TRENDware International Inc Table of Contents EROSI soeesccacteronenaesectseseconesnesiaesserelaconee nan oroeectecorntnsuacteerh avoreencnnceeectunee sees 1 1 Prepare for Installation oo ccccccsecsecssscsecssscsecsescsessesesesescseeseseneeees 1 2 Install Hardware pct sarensieczeceanenceteadegssnsindsaennncasctessnssadoeantoianesaseecsiesits 2 3 Configure the computer s TCP IP Settings oo cseseeeseseeseeseesees 3 4 Configuration svesaqurssasteneseAvesnnansavany iyesatiersteantapeannaritenassucerhendeuituesevepsennen 4 5 Connection through Telnet ccccescscscssseseesessssessessessesseseeeeees 9 6 Connection TROUGH CONSOLE sssrinin soni 10 7 Dynamic DNS Domain Name Server 8 Web Browser Dial Plan Sample ou ce ceccescsecsscsessescessescseeseeesnenes 14 English QIG 1 Prepare for Installation Thank you for purchasing the TVP 224HR This VolP Gateway Router will allow you to share your broadband Internet connection with wired 10 100Mbps Fast Ethernet computers as well as integrate your existing analog PBX phone system for Internet telephone This guide will help you setup and configure your VolP Gateway Router Following the installation instructions should be quick and easy If you run
6. ble that outlines the basic data you will require from your ISP Connection Type Data required Fixed IP Address Subnet Mask Default Fixed IP Static Gateway and Primary DNS Secondary DNS is optional PPPoE Login name and password Service Name is optional Usually none But some ISP may require a DHCP particular Hostname Domain name or MAC physical address After setting up Internet Access you will be able to Remote Manage the Gateway using the WAN IP By default the Web Access and Telnet Access management are enabled Both of these methods provide access over the internet so they do pose a potential security risk It is recommended that once configuration is complete both Web and Telnet access are disabled for security reasons Turning of Web Access disables access from the Internet however you will still have web browser access from the LAN side from a computer in the same segment If you prefer leaving Web and or Telnet access enabled be sure to change the administration password In the event that you should forget the password see section 6 Connection through Console Static or Fixed IP Cable Connection 1 From the Navigation Bar on the left side of the screen Click on the Internet Access Option From the Internet Access sub menu Select Fixed IP The Fixed IP Configuration page will appear 2 Enter all field information as provided by your ISP and Click Save TVP 224HR VoIP Gateway Router Fixed IP Net
7. ccess please reference the trouble shooting section of your user manual 6 Setup DDNS Client See section 7 on DDNS Client 7 English DHCP Connection 1 Click on the Internet Access option on the left hand side of the screen and Select DHCP The WAN PPPoE configuration page will appear TVP 224HR VoIP Gateway Router DHCP Client Settings DHCP Client a Hostname Use local MAC addr No N Local MAC addr 2 Enable DHCP and enter Hostname Domain Name and or WAN MAC Address To find the WAN MAC Address please navigate to Home System Status page if required by your ISP 3 Click Save 4 Reboot the TVP 221H system in order for the changes to take effect 5 Launch your web Browser Internet Explorer or Netscape Navigator Type http www trendnet com in the address bar and hit the Enter key If the website appears your router is configured correctly 6 Setup DDNS Client See section 7 on DDNS Client NOTE This quick guide covers only the most common situations Please refer to the User Guide CD for more information For console telnet configuration please reference the Advanced User Guide CD for more detailed information 5 Connection through Telnet To use Telnet Internet Access must have been previously setup so that the gateway is visible on the internet See User Guide for More Information Alternatively you can use Telnet to locally access the TVP 224HR if you are under a route
8. cted by LAN port Theoretically GW Ais in Taiwan Local Area Code have 2 digits and GW B is in the US Local Area Codes have 3 digits Gateway A 4 ports is configured as follows 1 Gateway A IP 192 168 1 20 mask IP 255 255 255 0 gateway IP 0 0 0 0 virtual IP 2 FXS Port 2 has a telephone set connected its phone number is 203 3 FXS Port 3 has a telephone set connected its phone number is 204 4 FXO Port 0 is connected to PBX There are two telephone sets connected to the PBX Their extension numbers are 800 and 801 5 FXO Port 0 is registered as number 9 and it is connected to PBX 6 PBX has an external line to PSTN Dialing 9 connects you PBX where 9 is dialed to connect to PSTN 7 The PSTN number to reach the PBX is 8888 2222 8 Telephone A s number is 7777 1234 and belongs to the local PSTN Gateway B 4 ports is configured as follows 1 Gateway B IP 192 168 1 55 mask IP 255 255 255 0 gateway IP 0 0 0 0 virtual IP FXS Port 2 has an analog telephone set connected its phone number is 203 3 FXS Port 3 has an analog telephone set connected its phone number is 204 4 FXO Port 0 is registered as number 9 Dialing 9 connects you to the outside line 5 FXO Port 0 is connected to PSTN line 9999 3333 6 Telephone B s number is 6666 4321 and belongs to the local PSTN NO Gateway A IP setup 1 Navigate to Internet
9. e gt 168 95 1 1 If the ping times out you do not have Internet Access Please refer to the trouble shooting section of the User Manual or consult your ISP to make sure your Internet Access Data is correct and accurately entered into the TVP 224HR The following commands enable disable web and telnet access respectively Console gt on off Net set http lt on off gt Net set telnet lt on off gt To reset to Factory Default settings please perform the following commands to Erase all port codec amp h323 configuration config erase Then access dial plan edit mode by entering atpm req Purge the dial plan from the database atpm purge all Store the changes atpm store Reset the network configuration to default net set fac_default net store net reset Key in yes to re boot 7 Dynamic DNS Domain Name Server This free service is a very useful feature It allows Internet users to connect to the TVP 224hR using a URL rather than an IP Address This also solves the problem of having a dynamic IP address With a dynamic IP address your IP address may change whenever you connect to the Internet making it difficult for others to find connect to the TVP 224HR With Internet DDNS your IP may change but your Domain Name is Static The Service works as follows 1 You must register for the service at www dyndns org using the dyndns org domain This is the only Dynamic DNS service currently supported 2 Aft
10. ed to configure the TCP IP settings in your PC Operating System OS Set up the PC to Obtain an IP address automatically Detailed setup procedures for Windows OS computers can be found in the User Manual on the CD provided If you are running any other OS please see your system documentation for configuration information 4 Configuration The TVP 224HR comes with default LAN IP addresses 192 168 0 1 The TVP 224HR DHCP server is always enabled and by default assigns 30 IP addresses starting from 192 168 0 10 You may use any PC to connect to the LAN port of TVP 224HR and then follow the steps below 1 Start your WEB browser In the address field Type in the following address http 192 168 0 1 2 The pop up screen should appear and prompt for user name and password The default values are User name admin all lower case Password 123 3 The following TVP 224HR VolP Gateway Router Graphical User Interface main page should appear If connection fails check all cable connections between the Cable ADSL Modem and TVP 224HR Internet Access The following set up information is designed to help you set up your gateway to connect to the Internet The set up is different depending upon the type of Internet Connection you have with your ISP Fixed IP PPPoE or DHCP If you re not sure what type of connection you have please contact your Internet Service Provider and collect the required information Below is a ta
11. entering the Gateway A Dial Plan as laid out in the tables below Telephone Table Hunt Group Table and Destination Table following the above procedures 2 After you have entered the Dial Plan make sure you Store Dial Plan to flash memory From the Navigation Bar on the left side Click on Store Dial Plan 3 The following screen will appear on the right side Click on YES TVP 224HR VoIP Gateway Router Store Dial Plan Settings To Flash Memory Ready to store Dial Plan settings to Non Volatile Storage Are you sure Gateway B Dial Plan Setup 1 Enter Gateway B Dial Plan into Gateway B as shown in the tables below Telephone Table Hunt Group Table and Destination Table following the above procedures 2 After entering all the information listed in the tables below DO NOT navigate away from Dial Plan Settings Click Store Dial Plan and click YES to save your dial plan to Flash Memory Gateway A and Gateway B dial plan setting Gateway A Table Number Table Prefix ol E d Dialing 203 calls phone No on FXS Port 2 ne Prefix strip Max Digits row No Dialing 204 calls phone on FXS Port 3 Dialing 800 calls PBX on None FXO Port 0 which then dials 800 Dialing 801 calls PBX on 3 FXO Port 0 which then dials 801 Dialing 9 from local phone on FXS Port connects you FXO Port 0 PBX where 9 is dialed for outside line After receiving 01
12. er registration follow the Service Provider s procedure to request a Domain Name and have it allocated to you Select Internet on the main menu then DDNS submenu to see a screen like the following TVP 224HR VoIP Gateway Router DDNS Settings 3 Enable Dyn DNS Please be sure to enter the data correctly For instance if you registered johnsmith dyndns org please make sure that dyndns org is in the Server Name Field and johnsmith is in the Host Name Field Please also to enter User Name and Password 4 Click Save 5 The TVP 224HR will then automatically ensure that your current IP Address is recorded and updated at the DDNS server If the DDNS Service provides software to perform this IP address update you should disable the Update function or not use the software at all 6 From the Internet users will be able to connect to your 224HR using your Domain name shown on this screen 8 Web Browser Dial Plan Sample This section describes how to use a web browser to build a dial plan in the VoIP Gateway We suggest the following when developing your dial plan Draw an application diagram to illustrate clarify application including 1 Local gateway IP setup 2 Local gateway local telephone number setup 3 Local gateway remote gateway IP amp remote telephone number setup NOTE The Diagram below of Gateway A amp B could be any combination of either the TVP 224HR connected to
13. g the dial plan and entering data please reference the User Manual for more examples Telephone Number Table 1 From the Navigation Menu on the left side Select Dial Plan Table Setup 2 From the window please Select lt Add gt lt Telephone gt 3 The following window will appear Please Enter Data as shown 4 Click on OK TVP 224HR VoIP Gateway Router Add Telephone Numbers Telephone Number 0 800 Hunt Group ID 4 Min Digits 3 e Max Digits 3 Strip Length 9 Append Prefix None at i A oa a y E Lhal Flan rable seiun English Hunt Group Table 1 From the Navigation Menu on the left side Select Dial Plan Table Setup 2 From the window please Select lt Add gt lt HuntGroup gt 3 The following window will appear Please Enter Data as shown 4 Click on OK TVP 224HR VoIP Gateway Router Add Hunt Group IDs Hunt Group ID 4 Destination ID 0 4 More Destinations for The Same Hunt Group r ri y G Oial Plan Table Setup Local Destination ID Table 1 From the Navigation Menu on the left side Select Dial Plan Table Setup 2 From the window please Select lt Add gt lt Local_Destination_Channel gt 3 The following window will appear Please Enter Data as shown 4 Click on OK TVP 224HR VoIP Gateway Router Add Local Destination ID Destination ID 4_ Channel Number 4 G Oial Pisa Table Setup Store Dial Plan 1 Continue
14. hat Telephone None on FXS Port gets you a line is attached to Port dial tone on FXO Port 0 for to GWA GW A FXS Internal Ext M B Dp Remote Zone used to 01 8 to 10 digits 2 Digit make calls to remote None Taiwan Area Code are sent GW A FXO 11 is stripped and Remote Zone used to None remaining 3 digits are sent make calls to remote to GW B External to PSTN Gateway B Hunt Group Table Gateway B Destination Table oe NOTE The above destination table has both local destinations and remote destinations When the gateways are taken out of this initial testing environment and implemented in the field the internet access settings will have to be updated In addition the above remote destination IP will have to be updated to the field IP address Case 1 Making a call between Gateway A and Gateway B Gateway B phone 203 calls to Gateway A phone 203 Caller Operation at GW B Equipment Operation Receiver Receiver Operation at WA at GWA 1 GW dial tone is heard Dial 11203 11204 11800 11801 2 VoIP call processing S R E emn OOOO S r The above process is the same for Gateway B phone 203 and 204 calls to Gateway A phone 201 800 and 801 Case 2 Gateway Phone to PSTN Phone Gateway B phone 203 calls to PSTN phone A number 77771234 Caller Caller Operation at GWE at GWB Equipment Equipment Operation Receiver Receiver Operation at GWA at GWA 1 GW dial tone i
15. into problems please refer to the detailed installation procedures on the CD User s Guide If you need further technical support please visit www TRENDNET com or call by phone Verify Package Contents Please make sure you have everything in the box AC Power Adapter RJ45 Ethernet LAN Cable RS 232 Console Cable Verify Equipment Before installing the VolP Gateway Router you should have 1 A working DSL Internet connection with Static IP or Dynamic IP with DDNS 2 Cable DSL Modem 3 A computer with wired network card installed 4 TCP IP protocol installed on each wired computer 5 A Web Browser such as Internet Explorer 5 0 or higher or Netscape Navigator 4 7 or higher 2 Install Hardware 1 Connect a RJ 45 network cable from Cable ADSL Modem to TVP 224HR s WAN port 2 Connect a RJ 45 network cable from one of the TVP 224HR s LAN ports to PC 3 Connect Analog Phones Fax machine using RJ11 to FXS port s WARNING Never connect a Trunk Line PSTN line to a FXS Port This will result In permanent damage to the FXS port 4 Connect FXO port s using RJ 11 Cable to PBX system or PSTN line 5 Power on your TVP 224HR TVP 224HR Verify Hardware Installation Make sure the following Router LEDs are on Power System blinking WAN LAN 100Mb s or 10Mb s Off 3 Configure the computer s TCP IP Settings To verify that your computer can communicate with your VolP Gateway Router you ne
16. r or switch and the TVP 224HR and your computer are in the same network segment To access the TVP 224HR Gateway from a remote location using Telnet perform the following tasks Open the windows command prompt and enter the telnet command followed by the IP address of the TVP 224HR Gateway you want to access When the TVP 224HR Gateway prompts you to Login enter the user name admin When the TVP 224HR Gateway prompts you for Password enter the password Console gt will appear The default password is 123 but it is recommended that the password be changed for security considerations The password can be changed from the Web Browser Administration Password submenu page Type in ping Xxx XxXXx Xxx where XXX XXX XXxX is your ISP provided DNS Server IP or any known Public Internet Address The following dialogue confirms Internet Access Console gt ping 168 95 1 1 ping lt 168 95 1 1 gt 56 data bytes 168 95 1 1 is alive E R R ping XXX XXX XXX If the ping times out you do not have Internet Access or the Public IP Address you pinged is incorrect Try another IP Address If you confirm that you do not have Internet Access please refer to the trouble shooting section of the User Manual or consult your ISP to make sure your Internet Access Data is correct and accurately entered into the TVP 224HR 6 Connection through Console The console port uses a DB 9 RS 232 connector The supplied straight through
17. s heard 1 Du Du is heard eee Ee ee a A Demem O ee The above dialing process is the same for phones 203 204 to any GW A local PSTN phone number Case 3 PSTN Phone to Gateway Phone Phone A number 03 77771234 calls to Gateway B phone 203 Receiver Operation at GW B Caller Operation at Phone A Equipment Operation phone 301 Pick up phone A 1 PSTN dial tone is heard n 1 Call being processed Te es Ce es ce eee Tem O eee The above dialing process is the same for any calls made from GW A local PSTN to remote phone numbers 203 amp 204 NOTE Case Tables 1 3 show the possible analog phone PBX PSTN integration applications of the Gateway Disconnect cadence provided by your phone company for your PSTN line and disconnect cadence provided by your PBX may require additional matching with the gateway This will require the assistance of your PBX supplier and or Systems Integrator Please also see User s Guide for additional information Certifications This equipment has been tested and found to comply with FCC and CE Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VO
18. switch by WAN port or the TVP 221H Connected by LAN port The switch that joins these two gateways serves the purpose of initial lab configuration Under this configuration both TVP Gateways To be also referred to as Gateway and GW must be in the same IP segment Once the dial plans have been entered and tested the switch would be replaced by the public internet and the gateways would then have to be updated with the field application Internet Access Settings eg Public IP Address Subnet Mask and Gateway IP Address In addition all remote destinations in the dial plan must be updated with the actual application field IP Addresses TE100 S5Pplus Phone A Internet Call Segment No Charge TITT 1234 Local Call Segment Local Charge NOTE This diagram serves the purpose of illustrating the possible analog phone PBX PSTN integration applications of the Gateway However disconnect cadence provided by your phone company for your PSTN line and disconnect cadence provided by your PBX may require additional matching with the gateway This will require the assistance of your PBX supplier and or Systems Integrator Please also see User s Guide for additional information Scenario description Two gateways connected by a switch There are two gateways connected by a switch They are generically labeled Gateway but could be any combination of either the TVP 224HR connected to switch by WAN port or TVP 224HR Conne
19. work Settings IP Address soa Subnet Mask 255 255 255 0 Default Gateway Primary DNS server Secondary DNS server 3 Reboot the TVP 224HR system in order for the changes to take effect 4 Launch your web browser Internet Explorer or Netscape Navigator Type http www trendnet com in the address bar and hit the Enter key If the website appears your router is configured correctly NOTE If the website does not appear please verify that the information is entered correctly Also call your ISP and verify your connection type If you still can not establish Internet Access please reference the trouble shooting section of your user manual PPPoE DSL Connection 1 Click on the Internet Access option on the left hand side of the screen and Select PPPoE The WAN PPPoE configuration page will appear TVP 224HR VoIP Gateway Router PPPoE Configuration Enable PPPoE No Transmit 2 Enter PPPoE User Name and Password as provided by your ISP 3 Click Save 4 Reboot the TVP 224HR system in order for the changes to take effect 5 Launch your web browser Internet Explorer or Netscape Navigator Type http www trendnet com in the address bar and hit the Enter key If the website appears your router is configured correctly NOTE If the website does not appear please verify that the information is entered correctly Also call your ISP and verify your connection type If you still can not establish Internet A
Download Pdf Manuals
Related Search