GFK-2961, RSTi-EP Slice I/O Analog Output Modules
Contents
1. 31 ppm current measurement K Max error between Tmin and Tmax 220 ppm FSR Monotony Crosstalk between the channels 0 001 FSR max Repeat accuracy lt 1 mV eff Output ripple max 0 001 Voltage load resistance gt 1 ka at gt 50 C 122 F max ambient temperature total sensor current of 10 mA per channel but 25 mA per module Current load resistance Actuator connection Short circuit proof Module diagnosis Individual channel diagnosis Yes es Substitute value Can be used with EP 19xx y module Supply Supply voltage 20 4V 28 8V Current consumption from 8 system current path Isys Current consumption from m output current path lout For public disclosure RSTI EP Slice Analog Output Module 3 GFK 2961 General data Operating temperature 20 C to 60 C 4 F to 140 F 40 C to 85 C 40 F to 185 F 5 to 95 noncondensing as per IEC 61131 2 Current consumption from the system current path Power consumption from input current path Power consumption from output current path Current demand of the connected sensors Current demand of the connected actuators Must be included when calculating the power supply EP 4164 EP 4264 Module Green Communication over the system bus Green Communication over the system bus Status Red Module System Fault or Diagnostic Fault Red Module System Fault or Diagnostic Fault Red Channel 0 at voltage output overload s2. Operational Notes None Product Documentation RSTI EP Slice 1 0 Module User Manual GFK 2958 RSTI EP Slice I O Functional Safety Module User Manual GFK 2956 1 800 433 2682 1 454 978 5100 www ge ip com GE Intelligent Platforms aa For public disclosure
3. power down prior to starting any maintenance activity Refer to the RSTI EP Slice I O User Manual GFK 2958 for additional information Refer to the RSTI EP Power Supply Reference Guide a software utility available on PME V9 00 for detailed power feed requirements Module Features Control up to four analog outputs Module diagnosis Spring style technology for ease of wiring DIN rail mounted Double click installation for positive indication of correct installation Analog Output Module Supports indirect firmware update through the network monitor Supports hot insertion and extraction 2015 General Electric Company All Rights Reserved Indicates a trademark of General Electric Company and or its subsidiaries All other trademarks are the property of their respective owners 2 RSTi EP Slice I O Analog Output Module GFK 2961 Ordering Information EP 4164 Analog Output 4 Channels Voltage Current 16 Bits 2 3 or 4 Wire EP 4264 Analog Output 4 Channels Voltage Current 16 Bits with Diagnostics 2 3 or 4 Wire Specifications Data Interface RSTI EP system bus System bus transfer rate Potential isolation Channel system bus yes Channel channel no Outputs Number Output levels 1 Voltage 0 5V 4 5V 0 10V 4 10V 1 5V 2 10V 2 Current 0 20 mA 4 20 mA Response time 1 ms for 4 channels Resolution 16 bits Accuracy 0 1 FSR max 0 05 FSR typ Temperature coefficient 20 ppm voltage
4. RSTI EP Slice I O GFK 2961 Analog Output Modules EP 4164 EP 4264 November 2015 GE provides 5 analog output modules with up to 4 analog outputs at 10 V 5 V 0 10 V 0 5 V 2 10 V 1 5 V 0 20 mA or 4 20 mA The resolution is 16 bit per Module Status channel An output can be connected to each connector the internal switching is Channel Status LED carried out automatically The output range is defined using parameterization A LEDs status LED is assigned to each channel The outputs are supplied with power from the output current path lour The EP 4264 module provides individual channel diagnosis with channel related error messages Each module features a type plate which includes identification information the key technical specifications and a block diagram In addition a QR code allows for direct online access to the associated documentation The software for reading the QR code must support inverted QR codes Markers are available as accessories for labelling equipment Each I O module can be labelled using the markers to ensure clear identification when replacing individual modules or electronic units The RSTI EP station is usually installed on a horizontally positioned DIN rail Installation on vertically positioned DIN rails is also possible The outputs as well as the sense lines of the AO modules must not be used as power outputs Modules should to be allowed to de energize for a minimum 10 seconds after
5. hort circuit at current output shunt resistance too high or line break detected Red Channel 1 at voltage output overload short circuit at current output shunt resistance too high or line break detected Red Channel 2 at voltage output overload short circuit at current output shunt resistance too high or line break detected short circuit at current output shunt resistance too high or line break detected Red Channel 0 at voltage output overload short circuit at current output shunt resistance too high or line break detected Red Channel 1 at voltage output overload short circuit at current output shunt resistance too high or line break detected Red Channel 2 at voltage output overload short circuit at current output shunt resistance too high or line break detected Red Channel 3 at voltage output overload short circuit at current output shunt resistance too high or line break detected For public disclosure 4 RSTI EP Slice I O Analog Output Module GFK 2961 Field Wiring The connection frame can take up to four connectors and four wires can be connected to each connector Those four connectors are shown in the following figure The Spring style technology allows either finely stranded or solid wire conductors with crimped wire end ferrules or ultrasonically welded wires each with a maximum cross section of 1 5 mm 16 guage to be inserted easily through the opening in the clamping terminal without ha
6. ion Diagrams Sense 1 Sense 1 A03 EP 4164 EP 4264 For public disclosure 6 RSTI EP Slice I O Analog Output Module GFK 2961 Connection Block Diagrams a l I p 0 i l F Sensa 0 I l l sense l I I ADO a l I G AQ i I Sense 9 l i Sensa Q i 1 gt l s I l D An 2 Q I Sense 2 id I I Sense 2 5 Ag i I 5 i l D AQ 3 I i Sanza 3 5 l Sensa 3 I 203 I I I l E E E EET J EP 4164 r oo sansa AQ 0 OO 16 Bit Cx AD 1 sense 1 or Th AD 2 sense 2 Sense 2 AD 2 Ol 000 ht AN 3 Tanza 3 3 3 OOK A ANNIX VA EP 4264 Release History Catalog Number Date Comments Version EP 4164 EP 4264 01 00 Nov 2015 Initial Release For public disclosure RSTI EP Slice Analog Output Module 7 GFK 2961 Important Product Information for this Release Updates Initial Release Funcional Compatibility Initial Release Problems Resolved by this Release None Initial Release New Features and Enhancements None Initial Release Known Restrictions and Open Issues None
7. ving to use tools To insert fine stranded wires without wire end ferrules the pusher must be pressed in with a screwdriver and released to latch the wire an i i R 8 a aa 8 ya js i Connector Block Connector Specifications e conductor cross section 0 14 to 1 5 mm 26 16 guage max ampacity 10 A 4 pole The modules do not have a fused sensor activator power supply All cables to the connected sensors actuators must be fused corresponding to their conductor cross sections as per Standard DIN EN 60204 1 section 12 Refer to the RSTI EP Slice I O User Manual GFK 2958 for additional information For technical assistance go to http support ge ip com Installation in Hazardous Areas EQUIPMENT LABELED WITH REFERENCE TO CLASS GROUPS A B C amp D DIV 2 HAZARDOUS AREAS IS SUITABLE FOR USE IN CLASS I DIVISION 2 GROUPS A B C DOR NON HAZARDOUS AREAS ONLY A WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I DIVISION 2 A WARNING EXPLOSION HAZARD WHEN IN HAZARDOUS AREAS TURN OFF POWER BEFORE REPLACING OR WIRING MODULES AND A WARNING EXPLOSION HAZARD DO NOT CONNECT OR DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS ATEX Marking II 3 G Ex nA IIC T4 Gc Ta 20 C to 60 C 4 F to 140 F For public disclosure RSTI EP Slice I O Analog Output Module 5 GFK 2961 Connect
Download Pdf Manuals
Related Search