TERMINATOR User Manual
Contents
1. Hd H M MH PAGE 19 TERMINATOR Section 15 Install Terminals The specific steps to install terminals into the stock guide depends upon the design of the stock guide which in turn depends upon the terminal For example un insulated open barrel terminals must be aligned with a rail that typically fits between the insulation and crimp portions of the terminal For mylar tape the slots in the tape must be secured in a hold down mechanism A generic procedure is provided below Contact Odyssey Tool if you have questions about loading terminals in a stock guide e Raise or remove the ram e Rotate the idler roller release to raise the idler roller above the drive roller e Slide the terminals carrier strip into the left side of the stock guide assembly across the anvil drive roller and idler roller Secure the terminals carrier strip in accordance with the specific design of the tool pack e Loosen the idler roller position thumbscrew e Slide the idler roller to position it above the carrier strip such that it has no interference with terminals that may pass through without getting terminated e Tighten the idler roller thumbscrew to secure the idler roller in position e Rotate the idler roller release to lower the idler roller against the carrier strip e Ifthe ram had been removed re install the ram Idler Roller Release Idler Roller Drive Roller Idler Roller Position Thumbscr2. ODYSSEY TOOL gr H Hd H M MH PAGE 23 TERMINATOR Section 18 Diagnostics TERMINATOR contains six diagnostic LED s to aid in troubleshooting problems They are described below ACADAPTER TEIE SOA TE em cose A 4 MS 0150 0001426 CAUTION FOR INDOOR USE ONLY Y A MADE IN CHINA Ab e AnLED on the power supply indicates that the supply is providing a 15 volt output e AnLED on the ram sensor toggles on off as the ram is moved up and down ODYSSEY TOOL guu Ha P eng PAGE 24 TERMINATOR Section 18 AAA Diagnostics continued e Four LED s on the side of TERMINATOR provide the status of supply voltages and sensors TS Toggles on off as terminals pass the terminal sensor RS Toggles on off as the ram moves up and down SV 5 volt supply 15V 15 volt supply e TERMINATOR executes a lamp test on the feed controller display for one second immediately after 1t is turned on Use the lamp test to verify that all display elements are working properly e TERMINATOR displays the software revision number for approximately 1 second immediately after a lamp test This revision number may be needed when contacting Odyssey Tool if you encounter problems ODYSSEY TOOL AAA PAGE 25 TERMINATOR Section 19 Maintenance To provide optimum performance and minimu
3. Location of stock guide identification number Location of ram tooling identification number ODYSSEY TOOL go H n rJ PAGE 12 TERMINATOR Section 9 Stock Guide Adjustment Wire Stop When used in a bench top press the wire stop must be adjusted to assist the operator in placing the wire over the terminal to the correct depth When used in fully automated wire processing equipment the wire stop aids in the removal of the terminal from the ram tooling One adjustment is available to position the height of the wire stop A second adjustment is available to control the front to back position The pictures below show the location of the wire stop and how it 1s adjusted for a representative sample of a stock guide Stock guide designs vary depending upon the specific terminal and may not appear exactly as pictured Wire Stop Height Adjustment Depth Adjustment ODYSSEY TOOL PAGE 13 TERMINATOR Section 10 Stock Guide Adjustment Terminal Sensor Section 5 describes how the feed controller is used to make fine adjustments in the left to right position of the terminal over the anvil using the electronics integrated into TERMINATOR The position of the terminal sensor on each stock guide determines the positioning of terminals over the anvil The terminal sensor position is adjusted at the factory to center the terminal over the anvil when a zero position offset is selected
4. Four LEDs are included on the feed controller to indicate the selected mode of operation The LEDs are labeled DELAY SPEED POSITION and RUN A three digit display 1s provided to display delay speed and position selections Four pushbuttons are provided to select mode of operation input data and display the number of feed cycles that have occurred The pushbuttons are Mode Used to select desired mode of operation This pushbutton transitions TERMINATOR through modes as follows MEE SPEED POSITION gt Up Down Used to increment decrement the number displayed in DELAY SPEED and POSITION modes If the UP or DOWN pushbutton is held closed the displayed number will increment decrement automatically until released or an upper or lower limit is displayed In any mode simultaneously pressing the UP and DOWN pushbuttons will display the total number of feed cycles Refer to section 6 FEED In RUN mode the FEED switch is used to initiate a feed cycle This is useful during set up to check terminal positioning because a feed cycle can be initiated without moving the ram ODYSSEY TOOL gr H Hd H M MH PAGE 8 TERMINATOR Section 6 AAA Display Number of Feed Cycles In any mode pressing the UP and DOWN pushbuttons simultaneously will display the total number of feed cycles made by TERMINATOR A feed cycle can be triggered in two ways e By upward motion of t
5. complete applicator does not have to be purchased for each terminal Unlike traditional applicators which use mechanical designs to feed terminals pre termination TERMINATOR uses a patented feeding method that electronically performs feeding operations downstream from crimping operations that 1s feeding occurs post termination TERMINATOR employs pinch rollers which engage the intact carrier strip after the terminal has been crimped to the wire and removed from the carrier strip The pinch rollers are driven by a stepper motor Microprocessor based electronics in conjunction with sensors initiates a feeding cycle on the upward motion of the ram and controls the stepper motor to precisely position the next terminal to be crimped A feed controller allows the operator to set feeding parameters electronically As a result of this superior terminal feeding system tool packs are readily accessible and easy to swap set up is quick and easy and compared to industry standard applicators it all comes at reduced costs and downtime ODYSSEY TOOL g M sHnng PAGE I TERMINATOR Section 2 AA Safety Precautions TERMINATOR is designed to provide many thousands of wire crimps reliably and safely Please read and follow all of the precautions listed below to avoid personal injury and equipment damage e Do not attempt to alter disassemble or adjust any part of this equipment that is not expressly
6. crimping process is complete and terminals have been removed from the carrier strip Make certain that the carrier strip is routed such that The strip cannot contact AC power cords The strip cannot contact AC power outlets The strip cannot enter equipment or tooling Operators avoid being cut by sharp edges that may be present on the edge of the strip During high volume production the carrier strip is cut periodically to prevent excessive amounts of the carrier strip from accumulating ODYSSEY TOOL __ M n PAGE2 TERMINATOR Section 2 AA Safety Precautions continued e Use only specified lubricants e The pinch rollers used by TERMINATOR to feed terminals can operator anytime TERMINATOR is connected to AC power and turned on TERMINATOR does not have to be installed in a press to operate the rollers Keep hands fingers and clothing clear of the rollers at all times e Stop operating TERMINATOR immediately if it emits smoke a strange smell or otherwise behaves abnormally e Unlike traditional applicators which use a mechanical linkage to the ram to feed terminals the ram in TERMINATOR moves freely As a result the ram in TERMINATOR can easily fall out When carrying or transporting terminator remove the ram or take precautions to prevent it from falling out ODYSSEY TOOL aS PAGE 3 TERMINATOR Section 3 Features and Benefits TERMINATOR s patented feedin
7. described in this manual e Avoid using or storing TERMINATOR tool packs power supplies power cords or cables in the following places e Places subject to temperatures above 104 degrees Fahrenheit or below 32 degrees Fahrenheit e Places that are humid or wet e Places that are excessively dusty e Do not cut damage alter or place items on the power cords e Use only specified AC power sources e Ensure that the TERMINATOR power cords and any extension cords that may be used are routed to avoid interference with equipment and personnel Keep power cords well away from damp or wet areas e Do not allow liquids or foreign objects to enter TERMINATOR e Do not use TERMINATOR in any press that does not have a compatible means to secure TERMINATOR to the press e Do not use TERMINATOR in any press or fully automated wire processing equipment without insuring that all safety guards and safety measures are in place and functioning properly e Do the following before making any mechanical adjustments on TERMINATOR removing or installing tool packs performing maintenance or making repairs e Turn TERMINATOR off e Disconnect power from TERMINATOR e If TERMINATOR is in a press turn off or remove power from the press e When installing tool packs ensure that the identification number on the stock guide matches the identification number on the ram tooling before crimping terminals e TERMINATOR dispenses the intact carrier strip after the
8. through 9 The table below provides the approximate speed for each selection inches second AAA A 2 AAA 5 3 5 0 i 0 19 3 Position Mode When necessary used to make fine adjustments in the left to right position of the terminal over the anvil The position of 0 is the reference or default position and will produce good terminations in most cases If necessary a position offset can be specified from 50 to 50 Each value moves the terminal approximately 0 001 inch For example a setting of 33 moves the terminal to the left of the default position by 033 inches A setting of 47 moves the terminal to the right of the default position by 047 inches Run Mode Terminals are advanced fed only in run mode A feed cycle is triggered by 1 the upward movement of the ram or 2 pressing the FEED switch Actual feeding begins after the delay period specified in DELAY mode has expired Terminals are fed at the speed specified in SPEED mode Terminals are positioned to the default position unless the position was modified in POSITION mode Please note the following If upward movement of the ram is sensed while in DELAY SPEED or POSITION mode TERMINATOR will automatically change to RUN mode and initiate a feed cycle If already in RUN mode upward motion of the ram will initiate a feed cycle while keeping TERMINATOR in RUN mode ODYSSEY TOOL PAGE 7 TERMINATOR Section 5 Feed Controller continued
9. TERMINATOR E TERMINATOR User Manual ODYSSEY TOOL EE TERMINATOR TERMINATOR User Manual Table of Contents NN Section Page Introduction 2 Safety Precautions 2 3 Features and Benefits 4 4 Overview of the Terminal Feeding Process 5 5 Feed Controller 6 6 Display Number of Feed Cycles 9 7 Power Supply and Switch 11 8 Tool Pack Identification 12 9 Stock Guide Adjustment Wire Stop 13 10 Stock Guide Adjustment Terminal Sensor l4 11 Stock Guide Adjustment Bellmouth 15 12 Adjust Crimp Height 16 13 Remove a Tool Pack 17 14 Install a Tool Pack 19 15 Install Terminals 20 16 Remove Terminals 2 17 Set Up TERMINATOR to Run a New Terminal 22 18 Diagnostics 24 19 Maintenance 26 20 Specifications 27 2 Contact Information 28 ODYSSEY TOOL gr H Hd H M MH TERMINATOR TERMINATOR User Manual Section 1 ta Introduction TERMINATOR is a left to right side feed applicator which installs in industry standard presses The terminal specific tooling which includes the stock guide assembly punches and anvil rear rail sensor pressure pad cutter retainer and crimping tools collectively referred to as a tool pack can be removed and installed easily and quickly As a result one TERMINATOR can be used to crimp a large variety of terminals simply through the purchase of additional tool packs Significant reductions in tooling costs can be achieved because a
10. ew ODYSSEY TOOL CE PAGE 20 TERMINATOR Section 16 Remove Terminals To remove terminals from TERMINATOR do the following Pictures of the items referenced below can be found in section 15 e Raise or remove the ram e Rotate the idler roller release to raise the idler roller above the drive roller e Release any hold down mechanism if applicable e Slide the terminals carrier strip out of the stock guide assembly ODYSSEY TOOL gr H Hd H M MH PAGE 21 TERMINATOR Section 17 Set up Terminator to run a new terminal This section describes how to set up TERMINATOR to run a new terminal It assumes that the TERMINATOR is installed in a press and has a tool pack and terminal already installed The tool pack terminal already installed 1s referred to as the old tool pack and terminal The tool pack terminal to be installed 1s referred to as the new tool pack and terminal For some steps sections are referenced which provide additional information about that step FOLLOW ALL SAFETY PRECAUTIONS OUTLINED IN SECTION 2 e Remove the old terminal refer to Section 16 e Remove the old tool pack refer to Section 13 e Install the new tool pack refer to Section 14 e Install the new terminal refer to Section 15 e Verify that the stock guide assembly is the correct mate to the tooling installed in the ram Verify that the tool pack was installed correc
11. g system and quick change tool packs provide the following features and benefits e TERMINATOR works in industry standard presses and automated wire processing equipment e Swapping tool packs to accommodate a different terminal can be done in less than one minute e TERMINATOR does not have to be removed from the press to swap tool packs e Swapping tool packs is easy because the feeding mechanism is physically removed from all tooling elements e Loading terminals is easy because the stock guide has very little drag and there are no feed pawls to interfere with the loading process e All of TERMINATOR s features and capabilities are integrated into the product no data interface to other equipment is required e Terminals are precisely positioned over the anvil with no positioning adjustments required If the operator chooses to modify the terminal position on the anvil a position offset range of 050 in 001 steps can be achieved electronically via the feed controller Although rarely needed larger position offsets are possible through mechanical adjustments e The speed at which terminals are fed is controlled electronically The operator can select one of nine speed settings e A delay can be set electronically to provide a delay between the time a feed cycle is initiated by the upward movement of the ram and the time at which feeding actually begins Delays provide time to allow a just crimped wire to get clear of the anvi
12. he ram e Pressing the FEED switch while in RUN mode TERMINATOR counts all feed cycles regardless of the method used to trigger a feed cycle The count value cannot be reset The count value is retained with or without power applied The count value is displayed one digit at a time most significant digit first For example if the count value is 57 119 the display will follow the sequence shown on the following page ODYSSEY TOOL gr H Hd H M MH PAGE 9 TERMINATOR Begin with display of three dashes Display the most significant digit of 57 119 Display three dashes Display the next digit of 57 119 Display three dashes Display the next digit of 57 119 Display three dashes Display the next digit of 57 119 Display three dashes Display the least significant digit of 57 1 19 SEISBTBESDTT ODYSSEY TOOL PAGE 10 TERMINATOR Section 7 Power Supply and Switch To connect electrical power to TERMINATOR do the following e Plug the power supply into an AC outlet 120V 60 hertz Power consumption does not exceed 30 watts e Plug the barrel connector on the power supply into the power input connector located on the rear panel of TERMINATOR Follow safety precautions listed in section 2 A power switch located on the rear panel of the TERMINATOR is used to turn power on and off When TERMINATOR is turned on after being turned off or after a
13. istance This distance is modified increased or decreased based upon a position offset specified by the operator e The feeding cycle ends TERMINATOR awaits the upward motion of the ram to begin another feeding cycle The next section describes how the operator uses the feed controller to set feeding delays speeds and position offsets ODYSSEY TOOL aS PAGE 5 TERMINATOR Section 5 AAA Feed Controller The feed controller illustrated below contains four LEDs O four pushbuttons O and a three digit LED display MODE LIL dl ur COUNT FEED LIL ALI bown DELAY O run POSITION There are four modes of operation Delay Mode Used to specify the time between the triggering of a feed cycle by the upward motion of the ram and the time the feed cycle actually begins Delays may be needed when TERMINATOR is used in a bench top press or in a fully automated wire processing machine Ten delay options are available and are represented by the numbers 0 through 9 The table below provides the approximate delay for each selection Delay Selection Approximate Delay seconds ODYSSEY TOOL _ Ha r ng PAGE 6 TERMINATOR Section 5 A Z HH Feed Controller continued Speed Mode Used to specify the speed at which terminals are advanced during the feed cycle Nine speed options are available and are represented by the numbers 1
14. k guide installed in TERMINATOR loosen the bellmouth lock nut e Adjust the bellmouth adjustment screw clockwise to move the stock guide toward you This increases the bellmouth on the front of the terminal and diminishes it on the rear of the terminal e Adjust the bellmouth adjustment screw counter clockwise to move the stock guide away from you This increases the bellmouth on the rear of the terminal and diminishes it on the front of the terminal e WARNING EXCESSIVE BELLMOUTH ADJUSTMENT CAN RESULT IN INTERFERENCES BETWEEN THE TOOLING IN THE STOCK GUIDE AND THE RAM TOOLING TO AVOID DAMAGING THE TOOLING MOVE THE RAM MANUALLY AFTER EACH ADJUSTMENT TO VERIFY THAT NO INTERFERENCES EXIST e Tighten the bellmouth lock nut Bellmouth Lock Nut Bellmouth Adjustment Screw ODYSSEY TOOL PAGE 15 TERMINATOR Section 12 AAA Adjust Crimp Height TERMINATOR is designed for use in a press having a shut height of 135 8 mm 5 35 The conductor crimp height adjustment range is 1 0 mm 039 The insulation crimp height adjustment range is also 1 0 mm 039 For the conductor and insulation crimp the resolution is 015 mm 0005 To adjust crimp height do the following e Refer to crimp specifications provided with the tool pack or provided by the terminal manufacturer e Adjust the conductor plate and insulation plate to 0 e Crimp a terminal and measure inspect the conductor and insulation crimp Increase the dial se
15. l before the next feeding cycle begins Set a delay as needed when TERMINATOR is used in bench top presses or fully automatic wire processing machines Ten delay settings are provided e Crimp force analysis available on selected automatic wire processing equipment is much more accurate and consistent because of the absence of a mechanical feeding mechanism e To optimize access to the feed controller it has a magnetic backing which allows it to be docked on the applicator or on the press ODYSSEY TOOL g M H X PAGE 4 TERMINATOR Section 4 Overview of the Terminal Feeding Process To get the most out of any product 1t 1s always beneficial to have a basic understanding of how the product works TERMINATOR executes the following sequence during each feeding cycle The press moves the ram upward This triggers a ram sensor to initiate a feeding cycle e Ifa delay has been set by the user no action is taken until the specified delay expires e The stepper motor is actuated to begin feeding terminals Feeding occurs at a speed selected by the operator Feeding continues until the terminal sensor which is an optical sensor located on the stock guide senses the presence of a terminal If a terminal 1s never sensed the motor will dispense three inches of the carrier strip and stop e Immediately after the terminal sensor has sensed a terminal the stepper motor continues to advance terminals a pre determined d
16. loss of AC power it will be restored to the state that existed when it was turned off or lost AC power If a feeding cycle is in progress when TERMINATOR is turned off or it loses AC power the feed cycle 1s terminated it will not complete that feeding cycle when it 1s turned on again Power Switch U S Patent No 7 565 735 and other patents pending Power Input Connector ODYSSEY TOOL g n PAGE 11 TERMINATOR Section 8 Tool Pack Identification Tool packs consist of two separate tools a stock guide assembly and ram tooling When a tool pack is installed in TERMINATOR it is imperative that the stock guide is the correct mate to the ram tooling Otherwise the tooling will likely be damaged when TERMINATOR is put into operation To verify that a stock guide assembly and ram tooling are mates compare the numbers as shown below and make certain that the numbers match After installing the stock guide assembly and ram tooling cycle the ram manually or operate the press in slow mode to verify that that the tools mate properly If the press is cycled at full speed with mismatched tooling the tooling will be damaged The pictures below show the location of the identification numbers for a representative sample of a stock guide and ram tooling Stock guide and ram tooling designs vary depending upon the specific terminal and may not appear exactly as pictured
17. m down time it is recommended that TERMINATOR and tool packs be cleaned inspected and lubricated every 8 hours of operation The recommended lubricants are NLGI Z2 Grade Lithium Complex EP grease or equivalent DO NOT USE SOLVENTS TO CLEAN TERMINATOR OR TOOL PACKS DO NOT IMMERSER TERMINATOR OR TOOL PACKS IN SOLVENTS OR CLEANING AGENTS TERMINATOR Cleaning e Remove the ram Do remove the crimp dial from the ram e Remove the tool pack e Using clean cloth remove grease and any other debris from the ram and assembly e Lubricate per the instructions below TERMINATOR Lubrication e With ram removed apply light coating of grease to each corner of the ram e Apply a light coating of grease to each corner of the ram guide e Re insert ram remove any excess grease or oil Tool Pack Cleaning and Inspection e Remove the tool pack from TERMINATOR e Using clean cloth remove grease oil and any other debris from the tool pack e Inspect the stock guide assembly and ram tooling with special attention to items that touch the terminal such as the tooling punch anvil die sections cutter and cutter retainer Replace any worn or damaged parts e Nothing on the tool pack requires lubrication ODYSSEY TOOL ____ M M a PAGE 26 TERMINATOR Section 20 Specifications Applicator Type Left to right side feed applicator Stand alone operation no need for host controller Compatibility with presses Fi
18. on the feed controller During normal use the terminal sensor should not have to be adjusted for the life of the stock guide If adjustment is necessary follow the procedures below The pictures below show the location of the terminal sensor lock nut and locator for a representative sample of a stock guide Stock guide designs vary depending upon the specific terminal and may not appear exactly as pictured e Select POSITION mode on the feed controller and set position equal to 0 e Loosen the terminal sensor lock nut e Ifthe terminal is falling short of the anvil rotate the terminal sensor locator clockwise If the terminal 1s overshooting the anvil rotate the locator counter clockwise e Tighten the sensor lock nut e Feed a terminal into position by raising the ram or pressing the FEED pushbutton while in RUN mode e Check terminal position over the anvil Repeat steps above until the terminal sensor is positioned properly Locator Lock Nut Terminal Sensor ODYSSEY TOOL PAGE 14 TERMINATOR Section 11 AAA Stock Guide Adjustment Bellmouth Bellmouth is adjusted at the factory During normal usage bellmouth should not have to be adjusted for the life of the tool pack If adjustment becomes necessary use the procedure below The pictures below show a representative sample of a stock guide Stock guide designs vary depending upon the specific terminal and may not appear exactly as pictured e With the stoc
19. tion 13 for pictures of all items referenced e Verify that that the stock guide assembly and ram tooling to be installed are the correct mates to each other Section 8 describes how this is determined e Ifatool pack is installed in TERMINATOR remove it Refer to section 13 e Locate the ram tooling in the ram and secure it in place by installing and tightening the retaining bolt e Ifthe stock guide assembly release is not already in the release position pull back on the release and rotate it either clockwise or counter clockwise to latch it in position Then slide the stock guide assembly into place on the TERMINATOR Rotate the release again either clockwise or counterclockwise to secure the assembly in place MAKE CERTAIN THAT THE RELEASE IS FULLY SEATED AND IN POSITION TO SECURE THE STOCK GUIDE ASSEMBLY IN PLACE e Plug in the terminal sensor e IMPORTANT Manually slide the ram up and down to verify that tooling meshes correctly Or if installed in a press run the press in slow mode If any interferences are observed then do the following e Verify that the stock guide assembly is the correct mate to the tooling installed in the ram e Verify that the stock guide assembly and ram tooling are installed correctly e Make certain that the release has the stock guide assembly properly secured e To avoid damage to the tooling do not operate TERMINATOR until matching tooling is installed correctly ODYSSEY TOOL gr H
20. tly Refer to sections 8 and 14 e Turn TERMINATOR on Refer to Section 7 e Set the conductor crimp and insulation crimp dials on the ram to 0 e Ifnecessary use the feed controller to select DELAY mode and set the delay to an appropriate value Refer to section 5 e Ifnecessary use the feed controller to select SPEED mode and set the speed to an appropriate value Refer to section 5 It is best to select the highest speed that is compatible with the equipment and terminal being used e Use the feed controller to select RUN mode Press the FEED switch to initiate a feed cycle to place a terminal over the anvil Depending on how terminals were installed it may be necessary to initiate more than one feed cycle e Observe the left to right position of the terminal over the anvil Modify the position of the terminal if necessary using the feed controller Refer to section 5 ODYSSEY TOOL TS PAGE 22 TERMINATOR Section 17 Set up Terminator to run a new terminal continued e Turn the press on Crimp a terminal to a properly prepared wire If possible run the press in slow mode to avoid tooling damage Inspect the crimp Make adjustments to crimp heights feed position or bellmouth as may be necessary e If TERMINATOR is being used in a bench top press make adjustments to the wire stop 1f necessary See section 9 e Using the feed controller place TERMINATOR in RUN mode Refer to section 5 e Start production
21. ts in most industry standard presses with shut height of 135 8 mm 5 35 Modifications to guards may be necessary Tooling Quick change tool pack Terminal Feed Mechanism Electronic stepper motor Delay Ten selections ranging from 0 to 5 seconds Speed Nine selections ranging from 25 in sec to 3 in sec Position Offset 050 to 050 in 001 steps Crimp Heights Conductor and Insulation Range 1 0 mm 039 Resolution 015 mm 0005 Power Requirements 90V to 240V AC 50 60 Hz single phase 30 watts Environmental 40 to 104 degrees Fahrenheit 10 to 90 relative humidity non condensing ODYSSEY TOOL gr H Hd H M MH PAGE 27 TERMINATOR E Section 21 Contact Information ODYSSEY TOOL 22373 Starks Drive Clinton Township MI 48036 Phone 586 468 6696 Fax 586 468 8422 Email sales odysseytool com ODYSSEY TOOL EE PAGE 28
22. ttings until acceptable crimps are obtained B APPLICATOR RAM E TIGHTEN LUNDUCIOR CRIMP P B CONDUCTOR PLATE INSULATION PLATE LLL DIA 2 989 TIGHTEN INDICA TOR E INSULATION CRIMP ODYSSEY TOOL CEE PAGE 16 TERMINATOR Section 13 Remove a Tool Pack All of the tooling required to crimp a specific terminal is referred to as a Tool Pack It consists of two pieces 1 Stock Guide Assembly This includes the stock guide anvil and all lower tooling in a single unit 2 Ram tooling All of the pieces of the ram tooling are clipped together to form a single unit To remove a tool pack from TERMINATOR do the following e Un plug the terminal sensor cable e Pull back on the stock guide assembly release and rotate it either clockwise or counter clockwise to latch it in position Then slide the stock guide assembly out of TERMINATOR Release Stock Guide Assembly ODYSSEY TOOL g M H M ung PAGE 17 TERMINATOR Section 13 Remove a Tool Pack continued e Remove the ram tooling retaining bolt followed by removal of the ram tooling Ram Tooling Retaining Bolt Ram Tooling ODYSSEY TOOL EE PAGE 18 TERMINATOR Section 14 AAA Install a Tool Pack To install a tool pack in TERMINATOR follow the steps listed below Refer to sec
Download Pdf Manuals
Related Search