Manual - Reface Industries
Contents
1. 36 0 07 Aan eee aera Lift Cam Switch is not detecting that the Lift Cam has reset back to the home position Bs pnssustami The machine is not detecting the proper amount of amperage on the main motor i EIEE EA Replace All Consumables Emergency Stop Emergency Shutdown Mode SECTION 5 QUICK START QUICK START How to Use Your Machine 1 Turn on power to the unit by moving the ON OFF switch to the ON position located in the rear of the unit 2 Select which type of repair mode you would like by pressing either of the Scroll Buttons located on the User Interface 3 Spread the Buffing Solution evenly over the surface of the optical side of the disc Note Avoid spreading solution on the clear plastic center ring of the disc since the machine will not touch this area and solution will still be visible after the repair cycle When not in use place the Buffing Solutions cap back on to keep moist FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY VOIDING YOUR WARRANTY FOR AUTHORIZED DISTRIBUTORS VISIT WWW VENMILL COM QUICK START SECTION 5 4 Open the Front Cover and place the DVD CD Blu Ray onto the platter with LABEL SIDE OF DISC FACING DOWN 5 Close the Front Cover and press the Start Button Once the cycle has completed open the Front Cover and remove your disc Important Note You may run a disc through the VMI 2500 more then 1 time If2. 10 25 in x 6 75 in Power Safe DC Power Part Number PNV2500 Supplies used with unit Buffing pads and Repair Solutions Warranty 1 Year Limited Process Simple to use one touch 20 FOR SUPPORT INFORMATION www venmill com 508 278 0091 866 864 002 1 0 TOLL FREE FOR NON NORTH AMERICAN SERVICE PLEASE CALL YOUR REGIONAL DISTRIBUTOR If you are not sure who your regional distributor is please contact sales venmill com MAILING ADDRESS VenMill Industries Inc 670 Douglas Street Uxbridge MA 01569 2001 RE ORDER INFORMATION FOR ONLY FORTHE USA CONSUMABLES USED WITH THE VMI 2500 VMI Combo Pack 1 wheel 2 bottles and 1 C2 Chif ssssssesssessseen PN2501 VMI Rubber Platter ssissevaisissesasiesnsstasassssiinniaiaiesaatusanininanaamnns PN2012G VMI Cleaner DiSC sssseessssssesssssseseossssssceosssssecrosssecrosssssecrosssssecrosssecrossssseee PN2519 2500M PNV2500 012612 2
3. be returned to the customer at their expense 2 SECTION 2 C2 Chip Getting to Know Your Unit Fan Power Cord Plug Top Cover TELL Buffing Wheel Disc Platter Items and Features of Your Machine SECTION 3 Items and Features of Your Machine INITIAL SETUP There are several items that have been provided with your VMI 2500 but which have been separated from the unit Please find these items stored within the packing material Buffing Solution There is one bottle of Buffing Solution that has been shipped with your VMI 2500 machine This bottle is rated for enough solution to run about 250 minutes of VMI 2500 machine use NOTE SHAKE THE BUFFING SOLUTION fereromens BOTTLE WELL BEFORE EACH USE eerie Consumable Counter Chip C2 Chip ee The VMI 2500 unit comes with a consumable counter chip which is good for 500 minutes of machine use This chip has been preinstalled on the back of the machine NOTE THE VMI 2500 CAN NOT OPERATE WITHOUT A C2 CHIP The amount of usage on this chip will be displayed on the front LCD Screen On the Main Menu in the middle section this is where the total Chip Count is displayed This Count located on the LCD Screen will decrease the amount of supplies left on the C2 Chip as the Operator continues to use the machine When the Chip count drops to 10 an asterisk will appear next to the Count line This is to inform the Operator that
4. become dirty and stiff This can result in an inferior repair and a decrease in your Buffing Wheel life expectancy The VMI 2500 Cleaner Disc cleans and softens your Buffing Wheel When should clean my VMI 2500 Cleaner Disc VenMill does not recommend going 17 VMI 2500 2550i Buffer FAQs past 5 runs without cleaning off your VMI 2500 Cleaner Disc If a build up of junk is noticed on the Cleaner Disc feel free to clean it off at anytime Can I clean a 3 inch disc Yes but you will need to obtain a special 3 inch adapter from VenMill Industries Can I run a 3 inch disc without an adapter No This will damage your 3 inch disc and your rubber platter Why is the Buffing Solution important The Buffing Solution is a unique formula which accomplishes two very important tasks prevents static charges from developing during the buffing process and adds in the repair process rendering the disc optically clear Must I use the Buffing Solution on my discs Yes Besides the inferior repair results the static charge produced during the buffing process can create unpredictable errors in the unit and may cause damage The center of my disc still has Buffing Solution on it after a repair The Buffing Wheel never touches the inner most clear plastic center of the disc If there is Buffing Solution in the center of the disc it can be wiped away To prevent this from happening only use the Buffing Solution on the recorded
5. needed a disc can be run multiple times throughthemachinetoachieve optimum repair quality FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY VOIDING YOUR WARRANTY FOR AUTHORIZED DISTRIBUTORS VISIT WWW VENMILL COM SECTION 6 Standard Maintenance Standard Maintenance RUBBER PLATTER When should I replace my rubber platter There is no specific time frame for how long a Rubber Platter will last it could be one day or one year depending on how the machine is used and maintained If the disc can no longer sit flat on the Rubber Platter or the imprinting on the surface is no longer visible then the Rubber Platter should be replaced If there are any nicks gouges edges that are lifted or tears the Rubber Platter should be replaced How to replace the Rubber Platter 1 Turn off power to the unit 2 Locate the two side panel thumbscrews and unscrew them 3 Lift side panel up and away from the machine 4 Locate the Rubber Platter 5 Peelold Rubber Platter off of the platen Note A razor blade or a scraper can be used to do this 6 Takethe new Rubber Platter and remove the white backing 7 Center and place the new Rubber Platter on the platen 8 Make sure the Rubber Platter is fully seated on the platen 9 Install the side panel and screw down the thumbscrews 10 Turn on power 11 Standard Maintenance SECTION 6 BUFFING WHEELS How to re
6. VMI 2500 Buffer Users Manual Covers setup getting to know your machine alerts amp warnings repairing an optical disc safety amp cleaning and FAQs For models 2500 and 2550i Light to Mid Commercial Use Maximum recommended daily use of 50 repair cycles VenMill Industries Inc 670 Douglas Street Uxbridge MA 01569 USA USA 800 928 0090 No Am 866 864 0210 Intl 508 278 0091 Fax 508 278 0005 www venmill com For purchasing the VMI 2500 2550i Buffer This unit is intended to clean repair the following discs Blu Ray CD ROMs Music EDDI CEEDED DEA s DED DEAE a G Discs Game Discs Books on disc all recordable CDs and DVDs double sided discs amp 3 Inch Discs only with adapter 2012 VenMill Industries Inc All rights reserved Under the copyright laws this manual may not be copied in whole or in part without the written consent of VenMill Every effort has been made to ensure that the information in this manual is accurate VenMill is not responsible for printing or clerical errors Names and designs are trademarks of VenMill Industries Inc Artwork and Design 2012 VenMill Industries Inc All Rights Reserved The maximum amount of repairs per bottle may vary based on cleaning cycle usage See www venmill com for more information CAUTION Units and consumables are designed for use in specific regions Your warranty will be voided if you purchase the equipment and or consumables outside of your
7. aner Disc and let it sit for a minute Using a paper towel wipe the buildup off the Cleaner Disc Start from the center and work your way out Make sure the Cleaner Disc is dry before use Another option is to use a plastic style bristle brush to scrub the surface Standard Maintenance FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY VOIDING YOUR WARRANTY FOR AUTHORIZED DISTRIBUTORS VISIT WWW VENMILL COM Standard Maintenance How to clean the Rubber Platter and why From time to time the Rubber Platter may become dirty When this happens dust particles can become entrapped in the top surface of the platter This causes the surface to become slick When the Rubber Platter is slick discs tend to slip on the surface In worse case scenario this slipping could cause a disc to break 1 Take any glass cleaner such as Windex and spray the Rubber Platter 2 Let the solution sit for about a minute 3 Wipe the rubber platter dry with a paper towel 4 If slippage continues replace the Rubber Platter How to clean the Fan Filter After 60 minutes of operation the machine will display Filter CLNR message This message is to indicate to the operator that they should clean out the fan filter to keep constant air flow in the machine 1 Locate fan guard on the back of the machine and pull off plastic guard 2 Remove filter and blow out collected
8. aner Disc cleans and softens your Buffing Wheel NOTE IT IS HIGHLY RECOMMENDED THAT YOU RUN THE CLEANER DISC ASTHE LAST CYCLE OFTHE DAY REGARDLESS OF WHEN THE CLEANER DISC WAS LAST RUN Rubber Platter The VMI 2500 unit comes with a preinstalled rubber platter There is no specific time frame for how long a rubber platter will last it could be one day or one year depending on how the machine is used and maintained If the disc can no longer sit flat on the rubber platter or the imprinting on the surface is no longer visible then it should be replaced If there are any large nicks gouges lifted edges or tares then the rubber platter should be replaced If the machine is making a high pitched squealing noise during the cycle then the rubber platter should be replaced Power Cord The VMI 2500 unit comes with a power cord based on the region that the machine is designated for This power cord simply needs to be installed into the power inlet located on the back of the unit Then proceed to take the other end of the power cord and plug it into a wall outlet 5 CA N TEA or REO zo CD gt ag gt Modes of Operation SECTION 4 Modes of Operation Regular This option encompasses any of the following types of discs CD ROMs Music CDs Data CDs DVDs HD DVDs Computer Discs Game Discs Books on Disc all recordable CDs and DVDs Double Sided Discs Blu Ray and PS3 Note On this mode of opera
9. are cautioned that any changes or modifications not expressly approved in this manual could void your warranty Operating room temperature is 72 F 22 C 12 F 7 C To prevent fire or shock hazard do not expose the unit to rain or moisture If you have any questions about this product you may call VenMill Industries Customer Service at 800 928 0090 USA or 866 864 0210 N Ameri CAUTION This symbol is intended to alert the user to the possible presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons EMERGENCY STOP Pushing either Stop or Open button on the ror front panel during the buffing cycle will stop the unit and reset the firmware A series of three beeps will be heard and the tray could open You may resume normal operation Gi FEC Opto Clear PATENT PENDING C US Technology 19 Specifications SECTION 8 SPECIFICATIONS Unit operates on 220 240V 50 Hz AC power 10 amp max Safety features Disconnectable power cord ON OFF switch Safety interlock when interior is exposed Process controlled to prevent operation when front cover is the opened position One thermal circuit breaker will shut off power if internal temperature exceeds 130 F 54 C Fan operates when the unit is running Emergency stop with any buttons or opening of the front cover Weight 21 bs Dimension 11 25 in x
10. debris 3 Re install filter and guard 4 Push any button on the user interface to continue with normal operation SECTION 6 FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY VOIDING YOUR WARRANTY FOR AUTHORIZED DISTRIBUTORS VISIT WWW VENMILL COM SECTION 7 For further assistance with questions not included please refer to our website www venmill com How often should use my VMI 2500 Cleaner Discs The VMI 2500 will indicate when itis time to run a cleaning cycle for the buffing wheel After 20 minutes of operation the Main Menu will display the message Cycle CLNR on the bottom section of the Cycle Mode line The Start Button will also flash an illuminated Red LED light At this point load the Cleaner Disc onto the rubber platter Note Make sure the Cleaner Disc is loaded Label Side Down Close the front cover and press the Start Button Upon completion the machine will reset back to the preset Regular mode and the Operator can now continue with using the machine VenMill highly recommends that the Cleaner Disc be run as the last cycle of the day regardless of when the Cleaner Disc was run last Why is the VMI 2500 Cleaner Disc important During the buffing process your Buffing Wheel removes oil dirt buffing solution and a small layer of plastic from the surface of your disc This build up over time will cause your Buffing Wheel to
11. designated region Purchase only through Authorized Distributors found on our website at www venmill com If uncertain please contact sales venmill com READ BEFORE OPERATING EQUIPMENT SECTION 1 Unpacking and Repacking sss ssssessssessssessssesssesssseresseesssesssseosseeosseeosseessseosssrosseeossees 1 SECTION 2 Getting to Know Your Unit ssessesseeseesessessessessessessesseoseoseoseosseseeseossessesseoreoseosesseesees 3 SECTION 3 Items and Features of Your Machine ccccccccsesessssessssssesessesescsecseseeseeeseeeeseseeeeecs 4 SECTION 4 Modes f OSS aU ON sessnissanisirnaruraiaa nesanstansnibeieseeets 7 SECTION 5 INS CAI A E E EE E E E E E T PETE 9 SECTION 6 Standard Maintenance ss sssessesssesseesscseesscsscesseossessesseesscessesscoseesseoserssesseesseeseesserss 11 Rubber Platter o cessesenacvvzsseuvnsvevetansisdsiotursevoravdenseroteuincdeniepseteonsutnuvasiedeeteanopastevesintess 11 BUTANO WHEELS sroin A 12 TMI e AN T E O E essen AA EE E N O AA N E OE 13 Machine Cleaning ss sssesssesssssssssssssssseosssossrossessseosstosseosseosstosseesseesstesseeoseroseross 14 SAS h U ori seteitiamanasuaaetaenmtiasee aioe 14 DE e A E O S A E sqamtacectineneeniorns 15 Rubber Platter sescsusssenncsarssnsuensvcvetansisisestursurasnsdenswrouevanededupsvainstteaupasvconedesepundeeveniicens 16 SECTION 7 VMI 2500 2500i Buffer FAQS ccccccessssesssssssesssssssessesnssessssassesscsucsesscsucsecec
12. e When the count drops to 10 an asterisk will appear next to the Count display This is to inform the Operator that supplies should be reordered At this point while acycleis running the Start button will flash from Green to Blue Then error message Low Chip will appear on the main menu Once the chip is depleted the machine will notify the Operator and no more cycles will be allowed until a new C2 Chip is installed Once a new C2 Chip is installed all counts will be reset The Operator does not need to perform a manual reset to the machine How do I replace my C2 Chip 1 Turn the machine around so that the back of the unit is facing you 2 Locate the C2 Chip 3 Pull the chip out and away from the RS232 port 4 Take the new C2 Chip and install it into the RS232 port 5 The machine will automatically reset the counters FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY VOIDING YOUR WARRANTY FOR AUTHORIZED DISTRIBUTORS VISIT WWW VENMILL COM Standard Maintenance How to clean out the machine Recommendation Clean the machine weekly 1 2 Turn off power to the unit Locate the two side panel thumbscrews and unscrew them Lift side panel up and away from the machine Remove any dust or debris from the machine Note Use canned air a vacuum or even by hand With a paper towel or cloth wipe off any buffing solution residue
13. eecaeescens 17 SECTION 8 SpecificationS ss sssesseesssessseesseesseesscessersseesstesseessteoseeoseeoseeoseeosereseeesetesereseresereseeesereseees 19 SECTION 1 SAVE ALL PACKING MATERIALS FAILURE TO USE PACKAGING DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO THE UNIT AND WILL VOID WARRANTY Parts that need to be saved are as follows VMI 2500 Shipping Box Internal Foams 2 foams total Outside Foam Left Outside Foam Right Protective Plastic Bag There is a charge plus shipping for packing materials if they are discarded UNPACKING 1 Open the Shipping Box Remove support documents accessories Pull out the VMI 2500 that is encased within the outside foams by pulling upwards Remove the left and the right outside foams Take the VMI 2500 out of the plastic bag Locate the two side panel thumbscrews and unscrew them Lift the side panel up and away from the machine Locate foam 2 which is positioned in the front part of the machine under the buffing wheel and remove Locate foam 1 which is behind the Main Motor in the back of the machine and remove Install the side panel and screw down the thumbscrews Remove any green tape located on the outside of the machine Plug in the power cord On the back side of the machine turn the ON OFF switch to the ON position LCD screen will power on and display a blue backlight with Menu Your VMI 2500 is now ready to be
14. ing Wheel If you do not see any improvement you will need to change your wheel My machine lost power and is not turning back on The VMI 2500 has been equipped with an internal thermostat to ensure that the machine does not overheat and cause damage to your machine or your digital media Once the internal temperature reaches about 130 degrees Fahrenheit the thermostat will turn off power to the machine so that it can cool down The machine may be down for about 15 minutes before the power will turn back on To help cool the machine down faster open the Front Cover If the power has not turned back on within an hour please contact Technical Support at 800 928 0090 May LCD panel just Blue Screened and the entire machine restarted If the Power Cord is not fully inserted into the back of the machine this can cause a short which will restart the firmware program on the logic board Remove the Power Cord from the back of the machine and then reinstall the Power Cord by pushing in as far as it can go How can tell how many total cycles have run on my VMI 2500 Turn on unit and open the front cover Press the repair button and the display will show how many total cycles you have run Totals are broken down by regular deep and clean cycles 18 SECTION 8 Specifications Disconnect unit from supply circuit before opening D connecter du circuit d alimentation avant d ouvrir WARNING AND CAUTIONS You
15. left on the side panel or internal walls Install the side panel and screw down the thumbscrews Turn on power How to clean the Splash Guard Recommendation Clean the Splash Guard weekly when the rest of the machine is being cleaned out 1 IMPORTANT Turn off power to the unit 2 Locate the two side panel thumbscrews and unscrew them 3 Lift side panel up and away from the machine 4 Locate the Splash Guard which sits on top of the main motor and above the Buffing Wheel SECTION 6 FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY VOIDING YOUR WARRANTY FOR AUTHORIZED DISTRIBUTORS VISIT WWW VENMILL COM SECTION 6 Pull up on the Splash Guard until it releases from the main motor Note The Splash Guard is a snap fitted piece Run the Splash Guard under warm water from any sink faucet Wipe away any left over buffing solution residue with a paper towel or cloth Reinstall the Splash Guard by snapping it onto the top of the main motor Note Pull the Splash Guard forward until it snaps into place a second time Install the side panel and screw down the thumbscrews Turn on power How to clean the Cleaner Disc The Cleaner Disc must be maintained on a regular basis You can identify that the Cleaner Disc needs to be cleaned by seeing a heavy buildup on the surface 1 Use a Glass Cleaner such as Windex on the surface of the Cle
16. place the Buffing Wheels 1 Turn off power to the unit 2 Locate the two side panel thumbscrews and unscrew them Lift side panel up and away from the machine 3 Locate the Splash Guard which sits on top of the main motor and above the Buffing Wheel 4 Pull up on the Splash Guard until it releases from the main motor Note The Splash Guard is a snap fitted piece 5 Located on front of the Buffing Wheel is a washer and a Spade style screw which holds the Buffing Wheel to the spindle Hold the Buffing Wheel with one hand and turn the Spade Screw counter clockwise with the other 6 Remove the screw and the washer from the spindle and pull off the old Buffing Wheel 7 Install the new Buffing Wheel Insert the washer and tighten down the screw 8 Reinstall the Solash Guard by snapping it onto the top of the main motor Note Pull the Splash Guard forward until it snaps into place a second time 9 Install the side panel and screw down the thumbscrews 10 Turn on power 12 SECTION 6 Standard Maintenance C2 CHIP When should I replace my C2 Chip Each C2 Chip is programmed for a total of 500 minutes of operation The amount of usage on this chip will be displayed on the front LCD Screen On the Main Menu in the middle of the screen this is where the total Chip count is displayed This Count will decrease the amount of minutes left on the C2 Chip as the Operator continues to use the machin
17. portion of the disc Can repair a Double Sided disc Yes VMI 2500 2550i Buffer FAQs Can repair a Blu ray disc Yes Can repair a disc that is warped or cracked No This may result in further damage to the media and or your unit How long will a bottle of Buffing Solution last If used properly one bottle of Buffing Solution should last approximately 250 minutes of machine operation You may order consumables through VenMill directly at www venmill com or through our current distributors located on our website under the Distributors tab If you have any questions please contact us at 800 928 0090 866 864 0210 Intl or email sales venmill com How much Buffing Solution must use VenMill suggests that the entire optical surface of the disc be covered with the Buffing Solution This will ensure optimal repair capabilities To achieve this place one dab North East South West and then spread around Can run my unit over 500 minutes without replacing the C2 Chip No Once the C2 Chip is depleted the unit will not allow for any more cycles to be run Once a new C2 Chip has been installed the machine will continue with normal operation Why is my Buffing Wheel discolored This indicates that the Cleaner Disc has not been run enough or that the Cleaner Disc is packed with junk and needs to be cleaned It may take several SECTION 7 runs with the Cleaner Disc to improve the condition of the Buff
18. s may cause damage to the discs themselves For this reason the VMI 2500 has been designed to notify the Operator to clean the Buffing Wheel After about 20 minutes of machine operation the Main Menu will display the message Cycle CLNR on the bottom section of the Cycle Mode line The Start Button will also flash an illuminated Red LED light At this point load the cean SECTION 4 Modes of Operation Disc onto the rubber platter Note Make sure the Cleaner Disc is loaded Label Side Down Close the front cover and press the Start Button Upon completion the machine will reset back to the preset Regular mode and the Operator can now continue using the machine At certain times the Operator may choose to run the Cleaner mode before the machine instructs the Operator to do so In order to activate this mode of operation press either one of the Scroll Buttons Once the machine is set to the Cleaner mode this will be indicated by a flashing Blue LED light illuminated on the Start Button The Cycle Mode displayed on the bottom section of the Main Menu will read Cycle CLNR Proceed to insert the Cleaner Disc close the front cover and press the Start Button Emergency Stop A situation may present itself in which an Operator may desire to stop a cycle prematurely At any time during the cycle the Operator may press any button on the User Interface or lift open the front cover to stop the cycle Once the button i
19. s pressed or the front cover is lifted open the cycle will stop and the Main Menu will display error message Emergency Stop Wait An illuminated flashing red LED light on the Start Button will also appear Once the machine has realigned itself Note The Front Cover must be closed in order for the machine to realign itself the machine will reset back to the last mode of operation that the Operator had selected previously The Operator may now continue with using the machine Replace Chip The consumables buffing wheel and buffing solution have been designed to be replaces all at the same time The consumables originally provided with the VMI 2500 and the VMI 2500 Combo Packs are all rated for 500 minutes of operation Each configuration is accompanied by a Consumable Counter Chip which informs the unit that the consumables have been replaced and installed The amount of consumable usage time is displayed on the Count line located on the Main Menu As the consumables deplete over time the Count line will expire down in number of minutes left on the chip Once the C2 Chip has reached 10 the main menu will display the following information FAILURE TO USE CONSUMABLES DESIGNED FOR THIS UNIT WILL CAUSE DAMAGE TO BOTH UNIT AND DISC THEREBY VOIDING YOUR WARRANTY FOR AUTHORIZED DISTRIBUTORS VISIT WWW VENMILL COM Modes of Operation SECTION 4 The asterisk symbol will appear next to the count down STAT READY time to indicate to
20. supplies should be ordered at this time At this point while a cycle is running the Start button will flash from Green to Blue and Error Message Low Chip will appear on the Main Menu Once the chip is depleted the machine will notify the Operator and no more cycles will be allowed until a new C2 Chip is installed Once a new C2 Chip is installed all counts will be reset The Operator does not need to perform a manual reset of the machine WARNING CONSUMABLE COUNTER CHIPS ARE DESIGNATED SPECIFICALLY PER COUNRTY CODE A USA REGIONED C2 CHIP WILL NOT BE COMPATIBLE WITH A EUROPEAN OR AUSTALIAN CODED VMI 2550i AND VISA VERSA SECTION 3 Items and Features of Your Machine Buffing Wheel The VMI 2500 unit comes with a preinstalled Buffing Wheel This wheel is good for a total of 500 minutes of use Cleaner Disc The VMI 2500 unit comes with a Cleaner Disc which is designed to be used in the machine for cleaning raking the Buffing Wheel The machine is designed to inform the Operator after about 20 cycles of use to run the Cleaner Disc through the machine NOTE Do not apply Buffing Solutions on the Cleaner Disc During the buffing process your Buffing Wheel removes oil dirt and a small layer of plastic from the surface of your disc This build up over time will cause your Buffing Wheel to become dirty and stiff This can result in damaged media and a decrease in your Buffing Wheel life expectancy The VMI 2500 Cle
21. the Operator that they should consider COUNT 050 ordering more supplies for their unit Another indication is CYCLE REG provided for the Operator during the actual repair cycle itself CTT Status line will read Low Chip and the Start button will flash from Blue to Green while the cycle is in process Once the C2 Chip has reached 0 the main menu will display STAT EMPTY the following information COUNT 000 CYCLE RC At this point the machine will not allow the Operator to run i any other operations until a new C2 Chip is installed To replace the C2 Chip SSS 1 Locate the used C2 Chip inserted on the back of the machine 2 Remove the used C2 Chip Once removed an exposed RS232 port will become visible 3 Install a new C2 Chip into the RS232 port WARNING CONSUMABLE COUNTER CHIPS ARE DESIGNATED SPECIFICALLY PER COUNRTY CODE A USA REGIONED C2 CHIP WILL NOT BE COMPATIBLE WITH A EUROPEAN OR AUSTALIAN CODED VMI 2550i AND VISA VERSA fd Once a new C2 Chip has been installed the main menu will STAT READY display the following information COUNT 500 CYCLE REG At this point the Operator can now resume operation Note _ There is no need for the Operator to perform any manual tesets to the main Once the new C2 Chip has been installed all counts are reset ERROR MESSAGES By ceternetetetercnns Magnetic Switch Sensor is not detecting that the Platter is in the home position
22. tion Blu Ray and PS3 discs may only be cleaned For a Repair solution for these types of discs run them on the Deep Mode The VMI 2500 is preset to run on the Regular mode as indicated by the Green LED light illuminated on the Start Button Located on the LCD Screen in the Main Menu on the bottom section this is where the Cycle Mode is displayed If the line reads Cycle REG then your unit is ready for a regular repair mode This mode is set to run for 1 minute Deep This option encompasses any of the following types of discs CD ROMs Music CDs Data CDs DVDs HD DVDs Computer Discs Game Discs Books on Disc all recordable CDs and DVDs Double Sided Discs Blu Ray and PS3 The VMI 2500 is preset to run on the Regular mode To switch the machine over to the Deep mode of operation press either one of the Scroll Buttons Once the machine is set to the Deep mode this will be indicated by a Blue LED light illuminated on the Start Button Located on the LCD Screen in the Main Menu on the bottom section this is where the Cycle Mode is displayed If the line reads Cycle Deep then your unit is ready for a deep repair mode This mode is set to run for 2 minutes Cleaner Over time the Buffing Wheel will become encased with dried compound and plastic particles Buffing Wheels left in this condition will affect the repair quality of the discs and in some extreme circumstance
23. used Unpacking and Repacking Unpacking and Repacking SECTION 1 REPACKING 10 14 1D i 12 13 Turn off power to the machine Remove the power cord from the back of the unit Locate the two side panel thumbscrews and unscrew them Lift the side panel up and away from the machine Locate the Main Motor Push down on the top front of the Main Motor so that the back end lifts up slightly Insert foam 1 behind the back of the Main Motor against the back wall of the machine Locate the Platter on the front of the machine Insertfoam 2 to the right of the Platter and below the Buffing Wheel Install the side panel and screw down the thumbscrews Place VMI 2500 into the Protective Plastic Bag Place machine into the left and the right outside foams Place VMI 2500 that has been encased within the outside foams and protective plastic bag into the Shipping Box Insert anything else that has been required by the Technical Support Department Close and tape box shut Write provided RMA number on the outside of the Shipping Box Note In order to send a machine in for servicing a customer must call Technical Support first 866 864 0210 to troubleshoot the unit If an authorized technician deems that the machine is in need of servicing they will provide the customer with an RMA form to fill out Any machine sent in without authorization may be denied delivery and will
Download Pdf Manuals
Related Search