FIAT Ducato X230 CITROEN Jumper X230 PEUGEOT Boxer X230
Contents
1. spring locking clamps and give them to the end user the hole of rebound pad e black for left side Find a place in the cabin where put PRESSURE CON valves Made holes to fit them showed in pict 5 and 6 40 TROL KIT valves Lock L plates pict 7 and fit them for manometers and 8 for inflating valves locking with ring nuts pict 8 Find a place in the cabin where put manometers and inflating Install manometers and inflating valves as showed in pict 9 10 I I fit them in the holes prepared before pict 5 6 using ring nuts and nuts Fit RILSAN pipes on pipe fittings red pipe for right side and black pipe for left side REAR BRAKE REGULATOR MODIFICATIONS INSTRUCTIONS Remove original brake regulator with Deliver at the end user user manual Mount the provided brake regulator out modify it s original settings and parts removed from the vehicle lever as shown in pict 14 IMPORTANT Use ALB red lever for commercial and camping cars with single leaf spring Use ALBI black lever for camping cars with double leaf spring vB GEINTEGREERDE LUCHTVERING P airsuspension ie SATEN Put the work pressure stick in a place visible for the driver in the euzona yonsa mauna aa Pressure of air suspension Pression des suspensione a air b 1 Luftfedervungdruck Ca In Aranaruna VALVOLA DI CONTROLLO TOP DRIVE CONTROL TOP DRIVE CONTROL VALVE REGULATION NOTE for the e2. VB Airsuspension ref 1520302001 A n airsuspension Rear integrative pneumatic suspension for FIAT Ducato X230 CITROEN Jumper X230 PEUGEOT Boxer X230 Since 04 1994 INSTALLATION INSTRUC TIONS PACKAGE CONTENT N YZ Preassembled brake regulator lever RED Right suspension Ix Left suspension 1x SMALL HARDWARE KIT GEINTEGREERDE LUCHTVERING INTEGRATIVE PNEUMATIC SUSPENSIONS Pressione sospensioni pneumatiche air suspension Pression des suspensione air Luftfedervungdruck Ring nut Support YB plate TOP DRIVE CONTROL Valve body MANOMETERS box com PRESSURE CONTROL KIT CLIPS KIT posed by Composed by Composed by RILSAN KIT PIPE composed e Manometers with plastic e Valve body with pipe fittings e Plastic clips 20x by ringnut 2x 2x Caps 0 eR e Red pipe 6 m e Inflating valves 2x e Black pipe 6 m e Caps for manometers 2x e Gauge support Ix e Support plate 2x Ringnut 2x Pneumatic system instructions 1x LEFT RIGHT SIDE s w LAFTSBIGHT S51 Say kora s i d SI E lt a t gop e 9 Sk x the vehicle eis i Place the suspension be Fit RILSAN pipe on pipe Place lower locking sys ridge to operate an te In ee comfortably Unscrew both left AVERE ane chassis in fittings of ia O tem of suspension on leaf and right rubber rebound pad sert the upper slide pin into e red for right side
3. xecution of pneumatic system follow specific instructions not included in this manual See the pneumatic gt anean system installation instructions form see picture right max 2 5 bar WARNING For the execution of the pneumatic system please strictly refer the specific given instructions In fact the system may vary according to the chosen version manual self levelling or electrical so than the instructions for the pneumatic system are stated in the apposite handbook enclosed at the purchased kit IMPORTANT do NOT use liquid Teflon hemp paints etc In case of problem and or information contact our technical office In case you fail to comply at this indications societies EUROSERVICE s r l and ESI Italia s r l aren t responsible for eventually damages derivates For further information contact us Distributed by VB air suspension Varsseveld Holland Frankenweg 3 Varsseveld Holland This leaflet is purely for illustrative purposes and may not reflect correctly the supplied parts The manufacturer re serves to amend the contents of it whenever necessary and without notice 4 040 1 IM ENG VB
Download Pdf Manuals
Related Search