Guard Phone for Apartment Unit
Contents
1. Warranty To receive after Sale service have the following ready when you contact our branches 1 Name of the product 2 Model number of the product 3 The area of problem 4 Phone number and address at which you can be contacted Warranty Card PRODUCT MODEL DATE PURCHASED WARRANTY PERIOD AGENCY ADDRESS E KOCOM Warranties the original purchaser of this product as follows 1 This product is produced under strict quality control and inspection procedures 2 If this product breaks down during proper use as a result of product defect KOCOM will repair it within one year from date of purchase free of charge 3 The following cases will be subject to charge even during warranty period a Breakdown during transport or through careless treatment by consumer b Breakdown cause by unauthorized repair or system modification c Breakdown caused by natural disaster or power disorder This manual is based on the date as shown in the right and specifications are subject to change without notice for quality improvement KIP 120 06 06 K lt oOcom Guard Phone for Apartment Unit KIP 120 User s Manual for Operation and Installation Key Features FND indication House no Guard master amp Main gate access panel ID display Call amp communication with residents amp extened Guard master Communication with main gate camera panel amp door ope2. Cautions for Use This product is only for home Do not the product for industrial or military use Do not handle the equipment with wet hand which may cause electric shock Do not place wet or metallic materials on equipment Water leakage or intrusion of metallic materials may cause fire and SO electric shock Do not block the ventilating opening of equipment or put alien substances into it which may cause fire and electric shock Do not use battery that is not designated or mix new battery with old ones Insert batteries to fit their polarity Explosion or leakage of battery may cause fire and injury of user When visitor s image or voice is not displayed on screen or not sounded from speaker please check his her identity before opening the door and contact our A S center Do not use equipment when lighting is expected or strokes It may cause fire and electric shock Do not open rear cover cabinet and cover of equipment It may cause electric shock e When using the existing wiring be sure of the suitability of it to the product and install the product Failure to this caution may cause fire e When moving equipment be sure that plug is detached from an outlet and communication cable is disconnected Damage on cables may cause fire Do not modify power cable or pull it with excessive strength which may cause fire and electric shock Do not modify equipment It may cause fire and electric sho
3. y Communication Method DUPLEX HANDSET CONVERSION test volume level Melody TONE SOUND interphone video phone and lobby phone Wiring 5 line polar wiring VCC GND Voice 1 Voice 2 DATA Wiring Distance Within power GND 1 2 300M Dimensions W 165 mm x H 220 mm x D 80 mm Functional Specification Interlocking indoor units with KIP 120 Guard master are limited as below e Video phone monitor KIV 202 KIV D202 KIV 102 KIV D102 amp KVM 520 e Audio phone handset KIP 603 e Main gate access panel Lobby phone Color video lobby phone KLP C100 KLP C104 KLP C108 amp KLP C112 B W video lobby phone KLP 100 KLP 104 KLP 108 KLP 112 KLP P100 KLP P104 KLP P108 KLP P112 Audio lobby phone KDP 100 KDP 104 KDP 108 KDP 112 e Guard master KIP 120 m Wiring Specification Based on the Bus type wiring system the 5 lines 17V GND VOICE1 VOICE2 amp DATA are connected to the main line in polarity In case the distance between KIP 120s and Lobby phone is over 30M or one more KIP 120 is extended the additional power supply DC17V 1 3A should be added in a system Lobby Phone Guardroom KLP 100 KIP 120 KLP C100 Series KLP 100 Series KLP P100 Series KDP 100 Series Terminal Box HH gt House Wiring 3 VOICE 1 4 VOICE 2 6 DATA Terminal Box Guardroom KIP 120 Inst
4. ck o e Call signal may cause damage on user s hearing ability e Voltage other than prescribed rated voltage is not permitted which cause fire and electric shock Do not use power terminal of product s main body in other equipment than prescribed ones It may cause fire and short circuit e In wiring work use the designated wiring materials Wiring work using other materials than designated ones may cause fire The equipment without waterproof marking shall not be installed at the place water leaks It may cause electric shock and short circuit When working be sure that power is disconnected Failure to disconnect power may cause electric shock Be sure that the power cable is connected and earths according to designated method Failure to connection and earth may cause fire Do not connect power to other terminals than designated ones e It may cause fire and electric shock e When building a system with the product do not connect the product other equipment than designated one It may cause fire OBVSEvVSEU AS e When installing A C switch do work after removing the substance that may cause short circuit or electric shock Before installing or providing A S service be sure that the power is disconnected Cautions for Abnormality When power cable is broken exposure of core or short circuit do not fail to replace broken cable with new one Failure to N replac
5. e and electric shock e Avoid direct exposure to sunlight and store equipment at the place free from dust and high temperature as you can High temperature of equipment may cause fire and electric shock Safety Instructions Warnings and Cautions of Each System This equipment is electronically precision equipment so do not arbitrarily disassemble it In installation of the product do not fail to follow the specifications specifications offered by KOCOM Do not touch the product with alien materials for example sticker magnet opener metal chopstick etc or insert them into the product it may cause reduction of the product s durability and harmful results to user as well In the rainy season water is likely to penetrate into the product along the wiring Thus U type finishing is recommended as a desirable method of end part finishing System for Multi unit Housing In installation be careful that other wiring or metallic substances should not contact to the system for multi unit housing In installation be careful that alien substances should not go into the system Before installation be fully aware of wiring specifications of each model In installation be sure that the length and dimension of wiring meet the requirement prescribed in installation manual Excessive strength and external shock may cause mechanical breakdowns of equipment Do not arbitrarily open the case of the product When u
6. e broken power cable may cause fire and electric shock When detecting any abnormalities in equipment communication is not available images do not be displayed on screen calling is not available or abnormal sound is heard immediately detach plug from an outlet or turn off circuit breaker or detach batteries from equipment in case that equipment has no plug before requesting repairs to sales agent or A S center Keeping connection to power supply may cause fire and electric shock When alien substances go into equipment immediately detach plug from an outlet or turn off circuit breaker or detach batteries from equipment in case that equipment has no plug before requesting repair to sales agent or A S center Inthe case of smoke or smell of unknown origin from equipment keeping use it may cause fire and electric shock Detach plug from an outlet or turn off circuit breaker or detach batteries from equipment in case that equipment has no plug and be sure to check no more smoke or smell from equipment before requesting repair to sales agent or A S center Since personal repairing work by user may serious accidents In any case do not repair equipment with your own hand When dropping equipment or breaking its cabinet detach plug from an outlet or turn off circuit breaker or detach batteries from equipment in case that equipment has no plug before requesting repair to sales agent or A S center Keeping use equipment may cause fir
7. event possible risks for users and other persons and damages to their property The meaning from power cables The failure to install cables separately may cause fire electric shock and communication troubles of each symbol is as follows After fully aware of meaning of each symbol read the following cautions Do not install the product on rolling table or sloping place Dropping or falling may cause damage on your product A This symbol means that wrong handling or ignorance of matters that this symbol indicates e In installation avoid the place exposed to tremor or shocks which may cause damages on your product may cause serious injury or even death of user Warnin gs e Even if your product is waterproof do not install it slanted place of water leakage which may cause a short circuit e For the product of wall mounting type with fixing pegs keep it safely Fixing pegs may cause injury of user A This symbol means that wrong handling or ignorance of matters that this symbol indicates may cause serious injury or property damage of user Cautions SO This symbol means the matter that user should not do at nay event Q This symbol means that user should follow the instructions Symbols on Drawing Install the product of wall mounting type carefully not to drop from the wall Dropping due to earthquake or tremors may cause injury of user When installing the product on the wall consider the thickness and
8. han one KIP 120 guard master is extended in a system and resident makes the call to the guard master KIP 120 all guard master KIP 120 in a system ring at same time And first picked up guard master KIP 120 is connected with resident house indoor unit 2 Calling In order to make the call to the house pick up the handset press the certain house number using ten key button and press call button Then the call sound from certain house unit is ringing for 30 seconds Once the resident being called answers the phone the line is connected for 3 minutes After conversation if the handset of KIP 120 is returned the line is disconnected Communication with lobby phone and door open function 1 Answering When the visitor from lobby phone KLP C100 KLP 100 KLP P100 or KDP 100 only makes the call using number 0 call button on the lobby phone to the guard house the call tone sound from KIP 120 is ringing for 30 seconds The lobby phone ID is displayed in the FND window Once the handset of KIP 120 is picked up the line is connected with the lobby phone After conversation if the handset of KIP 120 is returned the line is disconnected In case more than one KIP 120 guard master is extended in a system and visitor from lobby phone makes the call to the guard master KIP 120 all guard master KIP 120 in a system ring at same time And first picked up guard master KIP 120 is connected with visitor lobby phone 2 Door open Du
9. ing work be careful that wirings should keep away from the wall mounting pegs or other furniture at regular interval Contact of wiring with wall mounting pegs etc may cause short circuit electric shock and fire it is applied to all products with wall mounting pegs Use the prescribed standard wirings Non standardized wirings may give adverse effects on operation of product it is applied to both video phone and CCTV CCTV Camera Do not install at noisy places Do not install at the place exposed to electromagnetic waves Excessive electromagnetic waves may cause continuous noise on screen and mechanical troubles When installing camera outdoor please put it in the outdoor case Otherwise when it rains the camera may be broken or operate incorrectly Install the product at well ventilated places Do not use the product for medical or military uses Do not install the product at humid places It may cause reduction of the product s durability as well as fire and electric shock When lens is stained with alien substances clean it with soft cloth to prevent the damages on it Install the product out of reach of children Precautions for Operation Exterior Wiring Diagram As this device consists of electronic precision components do not attempt to disassemble Do not drop this device and avoid strong impact When cleaning do not use wet hand volatile benzene or paint thinner Use soft c
10. lified electrician e When replacing old fuse with new one do not directly touch it with bare hands Use insulated tools or contact A S center SeCe gt o eko kolol A Warnings Cautions for Use Do not install the product at bathroom or at the place near a washing machine or at other humid places It may cause fire or electric shock Do not install the product at the place near a dresser humidifier or heater Also avoid the place exposed to spark heat or humidity All of them may cause fire and electric shock Do not install the product at the place exposed to dust metals and harmful gas such as hydrogen sulfide gas all of which may cause fire and electric shock Do not install the product at the place exposed to water and chemicals This may cause fire and electric shock Do not scratch break or arbitrarily process power cable which may cause fire and electric shock Putting a heavy thing on a cable heating it or pulling it may cause impairment on it Do not place power cable at the place near heating equipment It may cause damage of cable s clothing material which result in fire ad electric shock When detaching plug from an outlet do not pull power cable Damages on power cable may cause fire and electric shock When detaching plug from an outlet please hold the plug tightly Do not detach plug from an outlet with wet hand I may cause electric shock C A Warnings
11. loths dipping in neutral detergent to wash this device and dry it with dry clothes Keep away from humidifier and stove High temperature and humidity may cause troubles P y z p y y 17V 1V VOICE2 Clean the exterior of this device with soft cloths at times to keep it in clean state GND ONC VOICE 1 DATA Component s Name E Front Side A Precautions for Wiring CI ev Power Lamp Green Se As incorrect wiring may cause the device s non operation or poor communication quality Use Lamp Yellow 000 please carefully conduct wiring work IA ORORO Ten Key Button When connecting a wiring chord to a terminal loosen screw insert the end of the chord into D the bottom part of screw and tighten the screw When fixing wiring chord use stapler not to cause damage to the chord Call Button To call press When using existing wiring please be cautious not to cause disconnection and short circuit bet Hl house number and call button Cancel Button Used to cancel a call after or during the call Product Specification E Rear Side Input Power DC 17V 1V Common power input Internal Operation Voltage DC 12 8V 1V J Consuming Electricity Max 1W standby mode Max 2 5W operation mode Guaranteed Operation Temperature 0 50 C O O p d Communication Mechanism Balance Circuit I Q Volume switch control saati
12. material of the wall Dropping in use may cause injury of user Cautions for Use Do not put heavy thing on the product Dropping or falling due to heavy things on it may cause injury of user A This symbol means that contents high voltage electric shock warnings etc to which user Cautions for Repairs and Maintenance should pay attention are included e Clean the dust inside the product regularly Failure to clean the dust for long time may cause fire For inspection and cleaning of the inside of product please contact your local sales agent his symbols means that a certain action is not permitted Specific points not permitted are depicted around this symbol for example in the left drawing disassembly is not permitted e When putting your hands into the inside of equipment be sure that plug is already detached form an outlet or circuit breaker is turned off e Be careful not to expose the product to benzene thinner or hot water e Do not expose detergent directly to the product in a way of spaying etc This symbol means instructions or is used to force user to do a certain action Specific e instructions are depicted on the drawing e Moving equipment be sure that the plug is detached from an outlet for example the left drawing instructs user to detach power plug from an outlet For equipment whose cables are connected to terminals please contact your local sales agent or qua
13. n function KLP C100 KLP 100 KLP P100 amp KDP 100 Upto 3pcs of KIP 120 extension in a system Powered from main power KOCOM CO LTD A Warnings gt Warnings for disposal Do not throw used up battery into fire places which may cause fire and explosion N Cautions Cautions for installation The relevant law obliges users to have a qualified electrician carry out wiring work for power supply Work by disqualified Cautions for Safety For safe use please stick to the following cautions e Read this cautions carefully and keep it within easy reach of you e For right installation read this cautions thoroughly Please install the product according to its specifications e This Cautions for Safety may include items that are not contained in specifications of the product that consumer purchases e Reading this cautions use the product in a right manner For further information please contact our A S center persons may cause fire and electric shock e Wiring work for communication cables needs techniques and experiences For this type of wiring work please consult to your About Symbol A variety of symbols are used in this Cautions for Safety and your products to guide you to use products in a right local sales agent e According to the standard for electric work and other relevant regulations install communication cables at the place away and safe manner and to pr
14. n it with dry towel or soft cloth Do not install camera at the place where water penetrates or leaks Penetration or leakage of water may cause electric shock or short circuit Home Auto KHV 444 454 446 456 Do not insert any metallic materials into the inside of fuse cover It may cause electric shock Do not close ear to speaker Abrupt call or signal may give harmful effects on user s hearing After turning power on and off check again that input contents are saved correctly Otherwise data may be missed when auto signal mode operates Use a standard detector Non standardized detectors are likely to cause fire due to excessive voltage or current Please install motion detector at a place easily detect the motions of subjects When detector is installed at a wrong place or obstacles block the front side of detector it cannot work well When setting night guard mode be sure that detector should be connected well Sufficiently charge the battery of wireless handset before using it Be careful that children should not throw battery Be sure to close battery cover When children throw or disassemble battery it may cause serious accidents Be careful that the polarity of the product matches to that of guardroom communication cable When polarity is reversed it may cause abnormal operations of the product or apartment system as a whole 4 Line Related Products KVM 604 624 524RG 524G 524GS 520 KCV 346 356 In wir
15. ring communication with visitor from lobby phone KLP C100 KLP 100 KLP P100 or KDP 100 only if the button on the KIP 120 is pressed the main gate is opened In case the door opener is equipped with the system
16. ruction for Operation E Call Volume Control VR1 Using volume switch in rear side the call volume sound can be adjusted E KIP 120 Guard master ID setting In case the additional KIP 120 is extended in a system the KIP 120 s each ID should be set up Please be noted that if the same ID number is used and set there might be communication error amp malfunction Main ID 70 ID 70 is set as factory default and do not need to set ID Sub ID 71 ID 79 Set the ID between number 71 and 79 1 Main ID Setting As the ID 70 is set as factory default you do not need to set it again 2 Sub ID Setting Pick up the handset Press 0 0 button in order gt Press the desired number between 71 and 79 Ex ID71 faa the handset New ID number is displayed in FND window OK mark displays Return 3 Communication with extended guard master Pick up the handset Press guard master ID number Ex 71 Once it is answered the line is connected Press Call button E Communication with resident indoor units 1 Answering When the resident makes the call to the guard house the call tone sound from KIP 120 is ringing for 30 seconds The house number is displayed in FND window At this time once the handset of KIP 120 is picked up it is connected with resident After conversation if the handset of KIP 120 is returned the line is disconnected In case more t
17. ser opens the case arbitrarily KOCOM may reject to provide A S service Lobby Phone KLP 100 104 108 112 KLP P100 P104 P108 P112 KDP 100 104 108 112 KLP C100 C104 C108 C112 A stroke of lighting or strong shock may give fatal and adverse effects on system Thus do not fail to ground the system For registration of household password please refer to user manual of the concerned product it is applied to ten key lobby phone products KLP 100 KLP P100 KDP 100 and KLP C100 Relay KVS 104P A relay can support up to four households In the case of over four householders additional relays are needed Video Amplifier KHU 102P In installation follow the specification for Video in output Video Phone In assembling the product be careful that wall mounting pegs should not contact with wirings Inconnection of cables strip its insulation off as much as necessary Excessive stripping off its insulation may cause short circuit Be careful that signal cables should not be wired with A C wiring it may cause poor display quality Do not drop handset its damage or short circuit due to drop may make communication impossible When connecting wires to terminals use standard screwdriver otherwise screws may loosen which will result in disconnection of wiring Do not clean CRT screen with wet towel or cloth When water penetrates into the product it may cause short circuit Do not fail to clea
Download Pdf Manuals
Related Search