user manual - Automation Products Group, Inc.
Contents
1. 27 a 28 32 Analog Qutputs 2 2 28 29 Trip Point Outputs irre 30 32 WU 33 35 Specification S etate ada 36 37 Automation Products Group Inc 2 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Warranty and Warranty Restrictions APG warrants its products to be free from defects of material and workmanship and will without charge replace or repair any equipment found defective upon inspection at its factory provided the equipment has been returned transportation prepaid within 24 months from date of shipment from factory THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES NOT EXPRESSLY SET FORTH HEREIN WHETHER EXPRESSED OR IMPLIED BY OPERATION OF LAW OR OTHERWISE INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE No representation or warranty express or implied made by any sales representative distributor or other agent or representative of APG which is not specifically set forth herein shall be binding upon APG APG shall not be liable for any incidental or consequential damages losses or expenses directly or indirectly arising from the sale handling improper appli2. cycle through the options until PARITY is m z 5 gt j Step 4 Press displa lt z 5 Step 5 Press access the communication Parity setting Step 6 Press W to change cycle trough the parity options ICI Step 7 Press m z 5 to accept the return to the Communications menu Automation Products Group Inc 34 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Stop Bits STOPbT Sets the number of stop bits for the RS 485 communications Options 1 Stop bit 2 Stop bits Setting the number of Stop Bits lt Step 1 Press enter the main setup menu or W to cycle through the options until COMM 15 gt Step 2 Press displa lt z Step 3 Press access the Communications settings menu or W to cycle through the options until STOPbT is goi Step 4 Press displa lt Step 5 Press vto access the Stop Bit setting Step 6 Press or cycle through the settings options Step 7 Press enr to accept the settings and return to the Communication settings menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 35 PG10 Rev B1 8 15 Sensor Number SENNUM Sets the PG10 s sensor address number
3. P Step 5 Press m NOTE 2 The peak value can be reset by pressing A Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 11 PG10 Rev B1 8 15 Advanced Settings AdVSET The Advanced Settings menu 15 used to customize the LCD display and to setup any optional features such as an analog output Auto Off AUTO This function is applicable to battery powered units only The Auto Off feature allows the user to designate the time of inactivity no buttons pushed until the gauge automatically powers down Options OFF 2 MIN 4 MIN 8 MIN 16 MIN 32 MIN and LIGHT NOTE 1 Selecting OFF disables the Auto Off feature the gauge will then remain powered indefinitely so long as sufficient voltage is being supplied gt 1 8 NOTE 2 Selecting LIGHT will keep the gauge continuously powered as long as the light sensor in the PG10 detects adequate light levels When the environment is sufficiently dark the PG10 will automatically shut down until the lighting once again reaches the threshold of the light sensor Setting the Auto Off feature Step 1 Press enter the main setup menu Step 2 Press or to cycle through the menu options until AdVSET is gt displa lt Step 3 Press enter the Advanced Settings menu or to cycle through the menu options until AUTO is PE Step 4 Press d
4. Full access except Full Scale Calibration is locked Mode 005 Locked Access All buttons locked except will power on off battery powered gauges Accessing the Operating Mode Setting Step 1 Simultaneously press and hold and y for approximately 3 seconds This will bring up the 3 digit mode number Step 2 Enter the desired mode number see Operating Modes above by using A or to change value of the flashing digit and to accept the value and advance to the next digit Automation Products Group Inc 6 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Accessing the Setup Menu Step 1 Simultaneously press and hold and for approximately 3 seconds This will bring up the 3 digit mode number Step 2 Using W to change the value of the flashing digit and v to advance to the next digit change the mode number to 000 Step 3 Press to enter the setup menu and press AJ or scroll through menu choices Exiting the Menu System Step 1 While in the main setup menu press A or V until EXIT is displayed Step 2 Press to exit the menu system Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 7 PG10 Rev B1 8 15 Maximum Minimum Reset MAXMIN Pressing the A or button while in operating mode will cycle betwe
5. access the Output Settings menu or W to cycle through the options until AL SET is displayed to access the Analog Low setpoint value A 5 digit number Step 4 Press gt Step 5 Press will appear with the first digit flashing Step 6 Press change the value of the first flashing digit Step 7 Press e to accept the value of the flashing digit and advance to the next digit repeat steps 6 and 7 until the desired Analog Low reading is fully entered Step 8 Press Ca to reenter the Output Settings menu Step 9 Press AJ or W to cycle through the options until AH SET is displayed Step 10 Repeat Steps 5 7 to enter the Analog High setpoint value Step 11 To exit the output menu press A or until EXIT is displayed and press vto exit to the main setup menu Automation Products Group Inc 28 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Analog Low AL CAL amp Analog High AH CAL Calibration Allows the user to calibrate or trim the endpoints of the analog signal output amp 20mA or OV amp 2V SV Calibrating the Analog Signal End Points Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 NOTE Step 9 Step 10 Step 11 Step 12 Step 13 Use a calibrated meter to monitor the analog output signal Force a low analog output signal 1 e
6. 4 20 mA CURRENT LOOP L1 4 20 mA Circuit C4 relay option shown Gauge Connector EXCITATION RL Process Controller 1 2 EXCITATION o F Relay 1 Common 4 o rRelay 1 Normally Closed 5 L o Relay 1 Normally Open Vin 4 20 mA CURRENT LOOP 6 Relay 2 Common 7 Lob Relay 2 Normally Closed 8 9 j Relay 2 Normally Open L2 0 2 V battery powered C4 relay option not available Gauge Connector 1 2 38 Process Controller GROUND L Vin RL Automation Products Group Inc Rev B1 8 15 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 Wiring continued PG10 L3 0 5 V L3 0 5 V C4 relay option shown Gauge Gauge Connector Connector 1 1 suPPLY 1 211 suPPLY VOLTAGE VOLTAGE 2 2 GROUND 3 Vin 3 Vin o Relay 1 Normally Closed Process 4 GROUND 4 elay 1 Normally Close Controller Process 5 controller 5 F Relay 1 Normally Open 6 6 Relay 1 Relay 2 Common 7 7 gt gt Relay 2 Normall
7. 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Communications COMM Used to configure RS 485 Modbus communications settings on models equipped NOTE The PG10 can function only as a slave device Baud Rate bAUd R Sets the baud rate for the RS 485 communications Options are 2400 9600 19200 33400 Setting the Baud Rate Step 1 Press gt to enter the main setup menu or cycle through the options until COMM 15 Cl Step 2 Press displaye 5 Step 3 Press access the Communications settings menu or cycle through the options until bAUd R is displayed to access the Baud Rate setting Step 4 Press gt 5 Step 5 Press Step 6 Press gt cycle through the baud rate settings m Step 7 Press accept the settings and return to the Communication settings menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 33 PG10 Rev B1 8 15 Parity PARITY Sets the parity for the RS 485 communications Options None Even Odd Setting the Communications Parity Step 1 Press enter the main setup menu or cycle through the options until COMM is Step 2 Press displaye lt Step 3 Press access the Communications settings menu
8. 4mA or either by adjusting the applied pressure or by adjusting the Analog Setpoints see Analog Setpoints on page 18 for details Press to enter the main setup menu IC IE Press to cycle through the options until Output 15 displayed Press m z to access the Output Settings menu Press 1 cycle through the setup options until AL CAL is gt j displa lt Press 0 access the Analog Low Calibration value A 5 digit number will appear with the first digit flashing Press change the value of the flashing digit Changing the digit farthest to the left will produce the coarsest adjustment while each successive digit moving to the right will cause subsequently finer adjustments Press to accept the value of the flashing digit and advance to the next digit repeat steps 7 and 8 until the desired Analog Output value is displayed on the meter Press reenter the Output Settings menu Press A or VW to cycle through the options until AH CAL is displayed Repeat Steps 7 9 to adjust the Analog High Calibration value To exit the output menu press until EXIT is displayed press exit to the main setup menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 29 PG10 Rev B1 8 15 Trip Points The PG1
9. VDC max Input Current 3 30 mA max Signal Variance 0 16 mA at set points Output Input 2 wire loop powered Resolution 14 bit Protection Reversed polarity 0 2 VDC Output Input Voltage excitation Battery powered Output Zero set point is 0 15 V with a 2 VDC span 0 02 VDC Output Input 2 wire Resolution 14 bit 0 5 VDC Output Input Voltage Excitation 9 to 28 VDC Input Current 6 mA max Output 0 5 VDC 0 5 VDC at set points Output Input Non isolated 3 wire Resolution 14 bit Protection Reversed polarity SPDT Relay Trip Points Maximum Switched Voltage 240 VAC 220 VDC Max Maximum Switched Current 5A Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 41 PG10 Rev B1 8 15 Notes Automation Products Group Inc 42 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Notes Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 43 Automation Products Group Inc Tel 1 888 525 7300 1 435 753 7300 Fax 1 435 753 7490 e mail sales apgsensors com www apgsensors com Automation Products Group Inc 1025 W 1700 Logan UT 84321 To order additional copies of this manual ask for APG document number 9003470 Rev B1 6 15
10. displayed enter the Datalogging menu or cycle through the options until LOG 15 displayed to access the Logging Control options or cycle through the setting options until CONTIN Step 3 Press Step 4 Press m z 5 Step 5 Press Coil Step 6 Press EVEN Step 7 Press is displayed m wa to enable logging and return to logging control menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 21 PG10 Rev B1 8 15 Setting Event Logging When Event Logging is enabled the gauge will log readings based on the status of one or both of the Trip Relays see Trip Relay programming on pages 30 32 NOTE Gauges not equipped with relay outputs will still use the Trip Relay settings for event logging Event logging can be set to initiate on one of the following conditions When Trip 1 is On TION When Trip 2 is On 2 When both Trip 1 amp Trip 2 are On TIT2ON When both Trip 1 amp Trip 2 are Off TIT2OF When Trip 1 is Off FIOFF When Trip 2 is Off 2 Step 1 Press vov to enter the main setup menu or cycle through the options until dATLOG is Step 2 Press displa lt lt a m z 2 Step 3 Press enter the Datalogging menu or YW to cycle through the options until EVENT is displayed to access the Event options St
11. displayed Step 5 Press es set using the 24 hour system e g 1 00 p m is 13 00 to enter the main setup menu Or V to cycle through the menu options until dATLOG is to enter the Datalogging menu options or to cycle through the menu options until DATE is to access the Date settings A 2 digit month number will appear with the first digit flashing Step 6 Press or to cycle the first digit and to accept the value and advance to the second digit Repeat the same process for the secon d digit and press v to accept and advance to the day of the month setting which will appear with the first digit flashing Repeat th Step 7 Press Step 8 Press process one last time by entering the year to apply the setting and return to Datalogging menu or V to cycle through the menu options until TIME 15 displayed Step 9 Press to access the time settings Repeat the process used to set the date to set the time hour minute seconds Tel 1 888 525 7300 Automation Products Group Inc Fax 1 435 753 7490 www apgsensors com sales apgsensors com 19 PG10 Rev B1 8 15 Logging Sample Rate SAMPLE Determine the interval between logged readings whenever logging is activated Options 1 second 1s 30 seconds 30s 1 minute 1m 30 minutes 30m 1 hour 1h and 1 day 1day Setting the Logging Sample Rate Step 1 Press vto enter the mai
12. to accept the value of the flashing digit and advance to the entered Step 8 Press AJ or to cycle through the options until BAR100 is displayed Step 9 Repeat Steps 5 7 to enter the Bar Graph 10095 value Step 10 To exit the advanced setup menu press W untii EXIT is displayed and press to exit to the main setup menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 15 PG10 Rev B1 8 15 Full Scale Range Adjust RANGE Allows the user to adjust the reading at full scale pressure The reading can be adjusted by 10 full scale NOTE The pressure reading must be within 5 of the full scale value in order to make Range adjustments For example a 1000 psi gauge would need to be reading between 950 psi and 1050 psi in order to adjust the Range feature If the reading is not within 5 of full scale NOAdJU No Adjustment will be displayed when trying to adjust the Range Adjusting the Full Scale Range Step 1 Ensure that the pressure reading is within 5 of full scale m Step 2 Press enter the main setup menu or Vto cycle through the options until AdVSET is L2 Step 3 Press displa z Step 4 Press to access the Advanced Settings menu or W to cycle through the options until RANGE is displayed to enter the Range adjust mode gt Step 5
13. water 60 F millimeters of mercury Setting the Unit of Measure Step 1 Step 2 Step 3 Step 4 Step 5 Press Press Press Press of me Press F4 ICI m NTR PI ENTR once to enter the main setup menu or to cycle through the options until UNITS is displayed to access the Units options or V to cycle through setting options until the desired unit re is displayed to apply the setting and return to the main setup menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 9 PG10 Rev B1 8 15 Using Custom Units CUSTOM The Custom Units setting allows the user to display a volumetric weight by applying a conversion factor to the pressure reading NOTE The conversion factor must be calculated using PSI as the base unit of measure Setting the Custom Units feature Step 1 Calculate the conversion factor from psi to the desired unit of measure MODE Step 2 Press 7 once to enter the main setup menu or to cycle through the options until UNITS is displayed to access the Units setting options or V to cycle through the Units options until CUSTOM is gt Step 3 Press m z 5 Step 4 Press Ci Step 5 Press displa E Step 6 Press to access the Custom Units setting A 5 digit conversion factor will appear with th
14. will re tare the gauge at the current pressure value Automation Products Group Inc 26 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Default dEFAUL Used to reset the gauge to the factory default settings Resetting the gauge to factory default settings Step 1 Press Z to enter the main setup menu Step 2 Press A or VW to cycle through the options until dEFAUL 15 displayed Step 3 Press to access the Default options Step 4 Press Vto cycle between NO and YES Step 5 Press em to apply the displayed setting and return to main setup menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 27 PG10 Rev B1 8 15 OUTPUT Used to configure any optional gauges outputs such as an analog signal or trip point relays Analog Low AL SET amp Analog High AH SET Setpoints Allows the user to define the reading values associated with the Low Analog signal i e 4mA or and the High Analog signal i e 20mA 2V or 5V NOTE The analog setpoints must be entered using the gauge s base unit of measure typically PSI Setting the Analog Signal Span F4 Step 1 Press to enter the main setup menu or cycle through the options until OUTPUT 15 gt j Step 2 Press displa Step 3 Press
15. 0 can be configured with dual relay trip point outputs The relays are SPDT mechanical in form Each trip point T1 and T2 can be configured to perform one of six different logic functions as described below and on the chart on the next page NOTE The or icon will appear in the upper left area of the display whenever the associated trip point is active Trip Relay Output Types T1TYPE or T2TYPE determines the logic function of the output relays see chart on next page Type 0 or Normally Closed setting will close the trip relay whenever the pressure is less than the Trip Pressure setting Type 1 or Exclusive setting will close the trip relay whenever the pressure is less than the Trip Pressure or greater than the Trip Pressure Trip Window Type 2 or Normally Closed with Hysteresis setting will close the trip relay when the pressure drops below the Trip Pressure Once closed the trip relay will remain closed until the pressure becomes greater than the Trip Pressure Trip Window at which point the trip relay will open Once open the trip relay will remain open until the pressure once again drops below the Trip Pressure setting Type 3 or Normally Open setting will close the relay whenever the pressure is greater than the Trip Pressure setting Type 4 or Inclusive setting will close the relay whenever the pressure is within the Trip Window pressure range greater than the Trip Pressure less than the T
16. AST CALIBRATE ZERO AND SPAN VIEW VIEW LOGGED SAMPLES EXIT CLOCK ON OFF EXIT m ALSET SET ANALOG LOW PRESSURE SET ANALOG HIGH PRESSURE P Y YES DEFAULT gt NG OUTPUT COMM BAUDR 2400 9600 19200 33400 TATYPE TYPEO TYPE1 TYPE2 TYPE3 TYPE4 TYPES SET ANALOG LOW CALIBRATION SET ANALOG HIGH CALIBRATION Y Y amm DE NONE EVEN ODD SET TRIP 1 PRESSURE EXIT NL M soe 1 STOP 2 STOP T1WIN SET TRIP 1 WINDOW SENNUM SET SENSOR NUMBER T2TYPE TYPEO TYPE1 TYPE2 TYPE3 TYPE4 TYPES EXIT T2PRES SET TRIP 1 PRESSURE T2WIN SET TRIP 1 WINDOW Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 5 PG10 Rev B1 8 15 Operating Modes The 10 has 4 standard operating modes to choose from Mode 000 Full Access Provides access to all menu settings If no buttons are pushed for 1 minute the gauge will revert back to Mode 003 factory default Mode 002 Limited Access Menu is locked zeros the reading press and hold for 3 seconds A or cycles between the and Min readings On Off functions only on battery powered gauges Mode 003 Factory Default
17. Operator s Manual PG10 Full Access DOC 9003470 Rev B1 8 15 Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com E mail sales apgsensors com PG10 Rev B1 8 15 Table of Contents Waranty 3 Programming the POTO i oe ter rerit e ure rena 4 32 Menu ode tnr erento de tee uon tu d aen a dex 5 Mod Sutin 6 Accessing Exiting the Setup 7 Maximum Minimum Function 8 Units of MeasUre eere Rok nena eno n FERRI hb Enn Ra a RN 9 Using Custom Units eroi ter a pe 10 Peak Hold Feature ene breite ten DSL 11 Advanced Settings i sese aeree Ite oue ste Ec 12 17 Deo e 12 Decimal P ace oett Fett tort sat eem te ire ted ua 13 Sample Rate icit 14 T 15 Range Adjustment t oed dedi ege 16 Quick 2 17 Dataloggin G 18 25 Date amp m 19 Logging Sample Rate Eve Ou 20 Event 22 Viewing Logged 668 2 2 2 2 2 2 2 2 0 4 41 11 4 24 Enabling Disabling the Clock 25 Tare 26
18. Press Step 6 Press m z 5 Step 7 Press increase the reading or press to decrease the reading Step 8 Press ove to accept the adjusted reading and return to the advanced setup menu Step 9 To exit the Advanced Setup menu press A or 15 displayed and press exit to the main setup menu Automation Products Group Inc 16 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Fast Calibration CALIBR Allows the user to perform a fast calibration of the zero and span NOTE Both zero pressure and full scale pressure must be applied to the gauge in order to complete the quick calibration process Step 1 Press 5 to enter the main setup menu Step 2 Press A or to cycle through menu options until AdVSET 15 displayed Step 3 Press to enter the Advanced Settings menu Step 4 Press Or to cycle through the options until CALIBR is displayed Step 5 Press to access the CALIBR mode The gauge will display the word ZERO prompting the user to perform the zero pressure quick calibration Step 6 Ensure no pressure is applied to the gauge Press A to zero the gauge The gauge will then display the word SPAN prompting the user to perform the full scale pressure quick calibration Step 7 Apply full pressure to the gauge and press to complete the quick calibration and ret
19. cation or use of the goods or from any other cause relating thereto and APG s liability hereunder in any case is expressly limited to the repair or replacement at APG s option of goods Warranty is specifically at the factory Any on site service will be provided at the sole expense of the Purchaser at standard field service rates All associated equipment must be protected by properly rated electronic electrical protection devices APG shall not be liable for any damage due to improper engineering or installation by the Purchaser or third parties Proper installation operation and maintenance of the product becomes the responsibility of the user upon receipt of the product Returns and allowances must be authorized by APG in advance APG will assign a Return Material Authorization RMA number which must appear on all related papers and the outside of the shipping carton All returns are subject to the final review by APG Returns are subject to restocking charges as determined by APG s Credit Return Policy Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 3 PG10 Rev B1 8 15 Programming the PG10 Each of the 4 buttons on the PG10 performs dual functions one within the setup menu system and another when in standard operating mode MODE Mode Button Primary Function Used to access the main setup menu or to return to the main setu
20. cess the Decimal Place setting options gt Step 6 Press 7 cycle through the resolution settings m 4 N Step 7 Press to apply the displayed setting and return to advanced setup menu Step 8 To exit the advanced setup menu press YW until EXIT is displayed and press sto exit to the main setup menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 13 PG10 Rev B1 8 15 Sample Rate SAMPLE Adjusts the rate at which the gauge takes sample readings NOTE Setting the Sample Rate to SLOW will help preserve battery life when applicable and will also help to smooth rapidly fluctuating readings Options SLOW 4x second MEdIUM 8x second FAST 16x second Setting the Sample Rate feature m Step 1 Press to enter the main setup menu or WJ to cycle through the options until AdVSET is P Step 2 Press displa lt z E ct Step 3 Press access the Advanced Settings menu Step 4 Press v to cycle through the options until SAMPLE 15 gt displa m NTI ct Step 5 Press access the Sample Rate setting options Step 6 Press P or W to cycle through the setting options until the desired setting is displayed da a m z 5 Step 7 Press to apply the display
21. e first digit flashing or Y change the value of the flashing digit vj to accept the flashing digit and advance to the next Step 7 Press m Step 8 Press digit repeat steps 7 and 8 as necessary Step 9 After the last digit 1s accepted by pressing em use or Y scroll through the custom units of measure LBF KN LBS KG NEWTON TON TONNES Step 10 Press to accept the custom unit Step 11 Press to shift the decimal point position Step 12 Press to accept the decimal point position and return to the main setup menu Automation Products Group Inc 10 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Peak Hold HOLd When the Peak Hold is enabled the gauge will display the peak or maximum pressure reading since the gauge was powered on or the Max Min value was reset NOTE 1 When the Peak Hold feature is enabled the PEAK icon will be displayed in the upper left area of the display Options Off or On Enabling the Peak Hold feature Step 1 Press oto enter the main setup menu or cycle through the options until P is displayed to access the Peak Hold setting options or 9 toggle between OFF and ON wa to apply the displayed setting and return to main setup menu Step 2 Press IL 5 Step 3 Press m z E Step 4 Press
22. ed setting and return to advanced setup menu Step 8 To exit the advanced setup menu press A or W until EXIT is displayed and press 5 to exit to the main setup menu Automation Products Group Inc 14 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Bar Graph 0 bAR 0 amp Bar Graph 100 DAR100 Settings Allows the user to define the reading values associated with 0 and 100 on the 270 display bar graph Bars will appear disappear in 1096 increments of the total span between the two values NOTE The 095 reference does not have to be the lower pressure setting 095 can be set as the higher pressure setting thereby causing the bar graph to increase as the pressure decreases Negative pressure settings can also be used as either the 0 100 reference points Setting the Display Bar Graph Step 1 Press once to enter the main setup menu Step 2 Press AJ or to cycle through the options until AdVSET is displayed Step 3 Press to access the Advanced Settings menu Step 4 Press AJ or V to cycle through the options until BAR 0 is displayed Step 5 Press to access the Bar Graph 0 value A 5 digit number will appear with the first digit flashing Step 6 Press to change the value of the first flashing digit Step 7 Press c next digit repeat steps 6 and 7 until the desired 0 reading is fully I1 m
23. en displaying the present pressure reading the maximum pressure reading and the minimum pressure reading The maximum and minimum readings will be stored until the gauge 15 powered down or the max min readings are reset Resetting the Max Min readings lt 3 m once to enter the main setup menu Or cycle through the options until MAXMIN 15 Step 1 Press Step 2 Press lt displa m z 5 Step 3 Press access the Max Min reset options Step 4 Press AJ Or to toggle between YES and NO until YES is displayed Step 5 Press 7 reset the Max Min readings and return to the main setup menu Automation Products Group Inc 8 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Units of Measure UNITS Allows the user to select the unit of measure to be displayed as the pressure reading Options For gauges over 120 psi PSI bAR KPA CUSTOM 2 FTH20 cmHG pounds per square inch bar kilopascals see Using Custom Units on next page kilograms per cubic centimeter megapascals feet of water 60 F centimeters of mercury For gauges less than 120 psi PSI bAR KPA CUSTOM mbAR INHG INH20 mmHG pounds per square inch bar kilopascals see Using Custom Units on next page millibar inches of mercury inches of
24. ep 4 Press gt Step 5 Press m z 5 2 Step 6 Press Aor cycle through the options until the desired Event condition is displayed Step 7 Press accept the event condition and return to the Datalogging menu Automation Products Group Inc 22 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Disabling Logging STOP and Clearing Logged CLEAR Readings Step 1 Press wove to enter the main setup menu Step 2 Press A cycle through the options until dATLOG is displa bes a m N 5 E Step 3 Press enter the Datalogging menu Or 0 cycle through the options until LOG is displayed to access the Logging Control options or to cycle through the setting options until STOP is displayed gt Step 4 Press Step 5 Press Step 6 Press CLE Step 7 Press m z m z to apply the displayed option stop or clear and return to Datalogging menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 23 PG10 Rev B1 8 15 Viewing Logged Readings VIEW The latest reading will be the first record displayed when viewing the logged readings to enter the main setup menu or W to cycle through the options until dATLOG is Step 1 Press Step 2 P
25. for the RS 485 Modbus communications Options 1 Stop bit 2 Stop bits Setting the number of Stop Bits lt to enter the main setup menu or W to cycle through the options until COMM 15 Step 1 Press gt Step 2 Press displa lt to access the Communications settings menu or W to cycle through the options until SENNUM 15 Step 3 Press oi Step 4 Press a displaye lt Step 5 Press sto access the Sensor Number setting 3 digit number will appear with the first digit flashing Step 6 Press A change the value of the first flashing digit Step 7 Press 0 accept the value of the flashing digit and advance to the next digit TOME repeat steps 6 and 7 until the desired sensor address number is entered The PG10 will automatically return to the Communications menu once the last digit is entered Automation Products Group Inc 36 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 Wiring the PG10 Battery Replacement Step 1 Step 2 Step 3 clockwise until the ring releases the display from the gauge place using the locking ring 8 Pin Connector Wiring PG10 Pinout Table Remove the front display to access the batteries PG10 Untwist the display locking ring on the face of the gauge counter Replace the front display ensuring p
26. ispla lt 2 5 Step 5 Press access the Auto Off setting options Step 6 is setting A or to cycle through setting options until the desired displayed Step 7 Press to apply the setting and return to advanced setup menu Step 8 To exit the advanced setup menu press until EXIT is displayed and press fenre to exit to the main setup menu Automation Products Group Inc 12 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Decimal Place dEC PL The reading can be set to display in High Resolution HI RES Medium Resolution MEdRES or Low Resolution LO RES mode Switching between resolutions will shift the displayed reading by one decimal place position NOTE Gauges without a decimal place position will display a dummy zero or zeros when the resolution is changed to medium or low Options HI RES high resolution MEdRES medium resolution or LO RES low resolution Setting the Decimal Place feature to enter the main setup menu or cycle through the options until AdVSET is Step 1 Press gt Step 2 Press NTR displa lt m Step 3 Press enter the Advanced Settings menu Or VW to cycle through the options until dEC PL is P Step 4 Press displa lt NTI Step 5 Press to ac
27. n setup menu Step 2 Press Jor to cycle through the options until dATLOG is BIE displa m z 5 Step 3 Press to enter the Datalogging menu or to cycle through the options until SAMPLE is P Step 4 Press displa z m Step 5 Press 5 to access the Logging Sample Rate setting options Step 6 Press or W to cycle through the sample rate settings 1 m z 5 Step 7 apply the displayed setting and return to Datalogging menu Automation Products Group Inc 20 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Logging Control Menu LOG Used to enable disable datalogging and to clear all logged records Setting the Logging Type continuous or event The PG10 can be set to continuously log readings or to only log readings based on the Trip Relay status NOTE 1 Gauges not equipped with relay outputs will still use the Trip Relay settings to define the pressure range s for the event logging see pages 30 32 programming details NOTE 2 Whenever the PG10 is logging whether in continuous or event mode the interval between logged readings is determined by the Logging Sample Rate setting see page 20 Enabling Continuous or Event Logging Step 1 Press to enter the main setup menu Step 2 Press AJor cycle through the options until dATLOG is
28. ons until CLOCK is to access the Clock on off option Or to cycle between the options to apply the displayed option and return to Datalogging Automation Products Group Inc Fax 1 435 753 7490 www apgsensors com sales apgsensors com 25 PG10 Rev B1 8 15 Tare TARE Enabling the Tare function will set the current pressure reading as the zero reference pressure in order to measure a net change in pressure as opposed to measuring the gross pressure Enabling the Tare feature Step 1 Press c to enter the main setup menu or V to cycle through the options until TARE 15 displayed to access the Tare setting options or toggle between OFF and ON Step 5 Press few button to apply the displayed option and return to main setup Step 2 Press Step 3 Press Step 4 Press PEJPI menu NOTE 1 When tare function is enabled the TARE icon will appear in the upper center of the display WARNING Do NOT disconnect the gauge from the pressure fitting while the tare function is enabled The gauge could still be under pressure even though the reading shows 0 NOTE 2 If the maximum gross full scale pressure value is reached while the Tare feature is enabled the PG10 will automatically disable the Tare feature and return to reading the gross pressure in order to help prevent the user from accidently overpressuring the gauge NOTE 3 Pressing and holding with the tare function enabled
29. p menu from any of the submenus Secondary Function Used to cycle the gauge on and off by pressing and holding for approximately 2 seconds Enter Button Primary Function Used to accept the value displayed within each menu setting Secondary Function Used to Zero the gauge or Tare the gauge when the tare feature is enabled by pressing and holding for approximately 3 seconds Up amp Down Arrows Primary Function Used to cycle through all options and settings within the menu system Secondary Function Used to cycle between the Minimum Maximum and the present pressure reading Automation Products Group Inc 4 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 PSI BAR KPA lt 120 PSI CUSTOM MBAR CUSTOM ONLY MAXMIN INHG TBF INH O KN MMHG LBS SET MULTIPLIER VALUE H gt ic TON PSI TON BAR TONNES KPA CUSTOM Siop 120 PSI KGCM2 CUSTOM ONLY MPA FTH O CMHG ADVSET gt AUTO OFF 2MIN 4MIN 8MIN 16MIN 32MIN LIGHT otc Dia HI RES MED RES LO RES DATLOG DATE SET DATE MM DDYY N SAMPLE SLOW MEDIUM FAST ime Y gt SETTIME HR MIN SEC Y BARO SET BAR GRAPH 096 1s 305 1m 30m 1hr 1day Y BAR100 SET BAR GRAPH 100 LOG Continuous Event Stop Clear RANGE SET RANGE 10 T2ON T10FF 2 EVENT T1T2ON T1T20FF CALIBR F
30. ress gt C displa e NTI to enter the Datalogging menu or W to cycle through the options until VIEW is displayed to access the logged readings Step 3 Press gt Step 4 Press m z 5 Step 5 Press Step 6 Press W to cycle back through progressively older readings will 2 4 cycle forward through progressively newer records Step 7 Press to exit the logged readings NOTE When viewing a logged record the time stamp of the record will toggle momentarily to display the date stamp once every 8 seconds Automation Products Group Inc 24 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Enabling and Disabling the Clock on the main display CLOCK When enabled the time will be displayed on the lower line menu line of the main display alternating every two seconds with the unit of measure Options ON or OFF Enabling or Disabling the Main Display Clock Step 1 Press 5 o 3 Step 2 Press displa m z Step 3 Press gt Step 4 Press displa m z 5 Step 5 Press Step 6 Press gt Step 7 Press m NTI menu Tel 1 888 525 7300 amp te a to enter the main setup menu or to cycle through the options until dATLOG is to enter the Datalogging menu or V to cycle through the opti
31. rip Pressure Trip Window Type 5 or Normally Open with Hysteresis is used for pump up applications or for a low level alarm with hysteresis function This is the opposite function of the Type 2 Type 6 Trip Disable Automation Products Group Inc 30 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Trip Pressure determines the lower pressure point for the trip output function Trip Window determines the pressure range between the lower and upper trip pressures Used for Types 1 2 4 5 see chart below TP TRIP PRESSURE TRIP WINDOW TYPE 0 FF NORMALLY CLOSED ON TRIP WINDOW 0 1 ON EXCLUSIVE TP TP TW OFF 2 NORMALLY CLOSED uot WITH HYSTERESIS EM tens pa 9 ERE TYPE 3 NORMALLY OPEN X P e ON H TRIP WINDOW O TYPE 4 OFF ON OFF INCLUSIVE TP TP TW 5 OFF ON NORMALLY OPEN WITH HYSTERESIS I OFF I Automation Products Group Inc APG Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 31 PG10 Rev B1 8 15 Setting the Trip Point Outputs Step 1 Press once to enter the main setup menu Step 2 Press Al or W to cycle through the options until OUTPUT 15 displayed S
32. roper alignment and secure into L1 L1 C4 L4 L4 C4 4 20 mA 2 SPDT Relays External 2 SPDT Relays with 4 20 mA Power with 4 20 mA 1 Excitation Excitation Excitation Excitation 5 2 n a Excitation Excitation Excitation 9 3 Excitation Relay 1 Com n a Relay 1 Com 54 n a Relay 1 NC n a Relay 1 NC 2 5 Relay 1 NO n a Relay 1 NO amp 6 n a Relay 2 Com n a Relay 2 Com 99 7 n a Relay 2 NC n a Relay 2 NC 8 CaseGnd Relay 2 NO Case Gnd Relay 2 NO 12 L3 L3 C4 L5 L5 C4 0 2 VDC 0 5 VDC 0 5 VDC RS 485 RS 485 with Batterywith External with 2 Tied with External with 2 Power Power SPDT Relays Power Relays T 1 n a Excitation Excitation Excitation Excitation 92 Output Excitation Exc Out Excitation Excitation 9 3 Output Output Output RS 485 A RS 485 A 54 n a Output Relay 1 RS 485 RS 485 B 5 n a n a Relay 1 NO n a Relay 1 NO a 6 n a n a Relay 1 2 Com n a Relay 1 Com o7 n a n a Relay 2 NC n a Relay 2 NO 8 Case Gnd Case Gnd Relay 2 NO Case Relay 2 Com n a indicates no pin connection Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Automation Products Group Inc 37 PG10 Wiring continued L1 4 20 mA Circuit Gauge Connector EXCITATION Process Controller Vin 1 2 EXCITATION
33. tep 3 Press to access the Output Settings menu Step 4 Press v to cycle through the options until TITYPE or T2TYPE is displayed Step 5 Press to access Trip Type setting Step 6 Press AJor change the setting to the desired trip type function Step 7 Press ewm to accept the trip type function and return to the Output Settings 1 menu Step 8 Press Alor cycle through the Output menu options until TIPRES or T2PRES is displayed Step 9 Press to enter the Trip Pressure setting 5 digit number will appear with the first digit flashing Step 10 Press or change the value of the first flashing digit Step 11 Press era to accept the value of the flashing digit and advance to the next digit repeat steps 10 and 11 until the desired Trip Pressure is fully entered Step 12 Press A or cycle through the Output menu options until TI WIN or T2WIN is displayed Step 13 Press to enter the Trip Window setting A 5 digit number will appear with the first digit flashing Step 14 Press Mor Vio change the value of the first flashing digit Step 15 Press to accept the value of the flashing digit and advance to the next digit repeat steps 14 and 15 until the desired Trip Window 15 fully entered Step 11 To exit the output menu press AJor YW until EXIT is displayed and press v5 to exit to the main setup menu Automation Products Group Inc 32 Tel 1 888 525 7300 Fax 1
34. urn to advanced setup menu Step 9 To exit the advanced setup menu press A or until EXIT is displayed and press v5 to exit to the main setup menu Automation Products Group Inc Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 17 PG10 Rev B1 8 15 Datalogging dGATLOG When datalogging is enabled the PG10 will log the pressure readings along with the associated date time stamps at an interval determined by the Logging Sample Rate setting see page 20 The 10 be configured to log continuously based solely on the Logging Sample Rate setting or to log only when user defined pressure conditions exist event logging The gauge will continue to log readings at the Logging Sample Rate interval for as long as the event conditions persist The gauge can store a maximum of 60 records Each record is logged in a FIFO first in first out buffer This means that once the buffer is full 60 records the oldest record will be overwritten by the next logged reading Automation Products Group Inc 18 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Date DATE and Time TIME Used to set the date and time which will be used as the reference for the time stamp of the logged readings NOTE Hours are Step 1 Press Step 2 Press A displayed Step 3 Press Step 4 Press
35. y Closed 8 8 9 j Relay 2 Normally Open L4 External Power C4 relay option shown Gauge Connector 1 1 suPPLY 2 VOLTAGE 3 o Relay 1 Common 4 9 F Relay 1 Normally Closed 5 o Relay 1 Normally Open 6 o Relay 2 Common 7 Relay 2 Normally Closed 8 9 _ Relay 2 Normally Open L5 RS 485 C4 relay option shown Gauge Connector 1 suPPLY 2 VOLTAGE 3 RS 485 A 4 RS 485 B Master Device 5 9 Ff Relay 1 Normally Open 6 9 j Relay 1 Common 7 Relay 2 Normally Open 8 o Relay 2 Common Automation Products Group Inc APG ge Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com 39 PG10 Rev B1 8 15 Specifications Overpressure 2x full scale Burst Pressure 4x full scale or 20 000 psig whichever is less Accuracy linearity amp hysteresis 0 25 or 0 1 B F S L Environmental Housing IP65 Compensated Temp 20 to 130 F 7 to 549 Storage Temp 40 to 160 F 40 to 71 C Operating Temp 0 to 160 F 18 to 71 C Electrical Batteries 2 standard C cell External Power 9 28 VDC Physical Weight 1 6 Ib 0 73 kg Case Material Injection molded Phenolic Automation Products Group Inc 40 Tel 1 888 525 7300 Fax 1 435 753 7490 www apgsensors com sales apgsensors com Rev B1 8 15 PG10 Output Specifications 4 20 mA Output Input Voltage Excitation 9 VDC min no load to 28
Download Pdf Manuals
Related Search