User Manual ELECTRONIC LOGGING DEVICE
Contents
1. RAND MSNALLY HD 100 User Manual Installing Your HD 100 gt Installation Instructions Installing your HD 100 can take as little as 10 minutes Installation Installation Instructions ene are provided p a gt lt as quick li 1 Locate the truck s diagnostic port Connect the cable to the port meme ee MN and turn the collar on the cable end to lock it in place Box contents NOTE For information on alternative installation options refer e HD 100 device e E Log sticker for vehicle to the Alternative Installation Options on page 13 e HD 100 device tray e 9 pin power cable e Get Started card e USB to Mini USB cable e User Manual e Adhesive mounting strips 2 e Driver and DOT Quick e Screws and nuts 4 Reference card e Cable ties 4 Does not include IntelliRoute TND 720 device 2 Route the cable from the diagnostic port to the location you selected for mounting the HD 100 device making sure to place it on a flat surface away from any vents and any locations where it may interfere with the driver NOTE Tuck the cable in the space between the windshield and the dash 8 HD 100 User Manual Installing Your HD 100 gt Installation Instructions 3 Connect the HD 100 to the cable and place it with the 4 Make sure the area selected is clean and dry Peel the protective tray attached on the flat surface layer off one side of the adhesive mounting strips and place on the bottom of the HD 100 tray Then peel o2. Rand McNally HD 100 Activation email you received after you completed the activation process Your log in information is provided in this email for your records Quick Diagnostics Once your HD 100 and IntelliRoute TND 720 are installed in your truck follow the Quick Diagnostic steps to ensure your system is working properly 1 Verify HD 100 Connectivity e Ensure the four colored lights are on These lights indicate that the HD 100 is connected and running properly e The JBus Blue light should turn on soon after connecting e If the Power Red Wi Fi Yellow or Cell Green lights remain flashing or off for more than 3 minutes after you connect your HD 100 device to the diagnostic port with the power cable then there may be an error Refer to the Troubleshooting section on page 14 2 Confirm access to HD 100 Home Menu e Click the HD 100 icon on IntelliRoute Home Menu e Log into the HD 100 software with your Driver ID e Confirm that the HD 100 Home Menu screen Is visible 3 Once you log on to the HD 100 software confirm Cell icon is visible on status bar For more information on the status bar refer to page 24 Installing Your HD 100 gt Quick Diagnostics 4 Once you log into the HD 100 software verify GPS and ECM connectivity e Select the Diagnostics tab then the GPS sub tab Confirm GPS status is good by verifying that there are values in the Latitude and Longitude fields For more information
3. 00 device Push the Reset button on the side of the HD 100 device Check power connection on HD 100 device Ensure the cable is secured to the truck s diagnostic port and to the HD 100 device Disconnect then reconnect both ends of the power cable making sure the collar on the diagnostic port end of the cable is locked in place Make sure truck ignition is on Restart the ignition Check that the colored lights are on The colored lights should illuminate within about 20 seconds indicating that the HD 100 is connected and running properly NOTE If after following these steps the green Cell light stays off this may indicate that you are currently located in an area without Cell coverage If you do not have Cell coverage you may continue to log on to the HD 100 software with your Driver ID and use the HOS application provided you have logged in at least once before with that particular Driver ID Your HD 100 will continue to capture your Hours of Service data and once you regain Cell connectivity your Hours of Service data will update Installing Your HD 100 gt Troubleshooting Cannot access the HD 100 software after clicking the HD 100 button from the IntelliRoute Home Menu e Make sure your IntelliRoute TND 720 device is within 10 feet of the HD 100 device e Wait up to 3 minutes for the colored lights on the HD 100 device to illuminate e Push the Reset button on the side of the HD 100 device Blue ligh
4. ff the other protective layer and place the device with tray attached on your dash in the desired location pressing firmly to secure it to the dash surface NOTE Do not cover the HD 100 device or place anything over it as this may interfere with the GPS signal HD 100 User Manual 9 Installing Your HD 100 gt Installation Instructions 5 Once the HD 100 device is mounted and connected to the 6 Now mount your IntelliRoute TND 720 if it is not already vehicle turn on your engine The four colored lights on the side Then turn on your IntelliRoute TND 720 device You will first of the device should illuminate within about 20 seconds see the IntelliRoute software Home Menu Click the HD 100 indicating that the device is connected and running properly button on this screen For more information on how the colored lights work refer to NOTE Because your IntelliRoute TND 720 displays your Hours the Quick Diagnostics section on page 12 of Service logs and helps you keep track of your compliance Rand McNally recommends that you keep your IntelliRoute i TND 720 plugged in with the charging cable while in use with er EA the HD 100 Power Button Vv Wi Fi JBus RAND MSNALLY HD100 HD 100 IntelliRoute TND 720 7 Once the HD 100 software loads log on by entering the Driver ID you created when activating your device through the Rand McNally Dock then tap Submit NOTE You can also refer to the
5. on the Diagnostics tab refer to page 52 e Drive the truck at least 0 2 miles Select the SysInfo icon from the HD 100 Home Menu Select Diagnostics then the JBus sub tab e Confirm that there is an odometer value in the Eng odom field Once you confirm all of these items are operating correctly the system is ready to use HD 100 User Manual 11 Installing Your HD 100 gt Quick Diagnostics Power Cell Red Green Wi Fi JBus External Antenna Port Power Mini USB Reset Port Port Button For use with external antenna when installing the HD 100 device behind the dash or under the seat 12 HD 100 User Manual on DevkePoweredOn Fasting System alert HOS aes oft Noponeridevce tuned of on comes Flashing Atemptingtocmect Wi Fi Yellow ch fom cometed oo G j Flashing Attempting to connect off Not connected Not connected JBus Blue Installing Your HD 100 gt Alternative Installation Options Alternative Installation Options Contact Rand McNally Customer Support at 1 800 641 RAND 7263 Accessories and parts for alternative installations can also be or fleetsupport randmcnally com for more information on purchased at randmcnally com fleetaccessories alternative installation options Customer may select from various professional installation d 0 6 pin Cab le Adapter For use in trucks with a options A list of certified installers can be found at 6 pin compa
6. t is still off for more than 3 minutes after connecting HD 100 to diagnostic port JBus is not responding on HD 100 device e Make sure truck ignition is on e Restart the ignition e Restart both the IntelliRoute TND 720 and HD 100 devices Log off the HD 100 software Press the Power button on your IntelliRoute TND 720 device Disconnect the cable from your HD 100 device Reconnect the cable to your HD 100 device e Check that the blue light turns on The blue light should illuminate within about 20 seconds indicating that the device is connected to the vehicle s ECM HD 100 User Manual 15
7. tible diagnostic port randmcnally com HD100installation e External Antenna For use with the HD 100 when installing behind the dash or under the seat HD 100 User Manual 13 Installing Your HD 100 gt Troubleshooting Troubleshooting This section covers basic troubleshooting scenarios For the most up to date troubleshooting information refer to randmcnally com HD100troubleshooting NOTE To remain compliant you must keep paper logs if your HD 100 or IntelliRoute TND 720 is not functioning properly 14 HD 100 User Manual Red light is off for more than 3 minutes after connecting HD 100 to diagnostic port No power on HD 100 device e Check power connection on HD 100 device Ensure the cable is secured to the truck s diagnostic port and to the HD 100 device Disconnect then reconnect both ends of the power cable making sure the collar on the diagnostic port end of the cable is locked in place e Check that the red light turns on The red light should illuminate within about 20 seconds indicating that the device is receiving power from the vehicle Nothing appears on the IntelliRoute TND 720 screen e Make sure your IntelliRoute TND 720 is charged and powered on Yellow or Green lights stay off for more than 3 minutes after connecting HD 100 to diagnostic port Wi Fi or Cell not connecting on HD 100 device Make sure your IntelliRoute TND 720 device is charged and within 10 feet of the HD 1
Download Pdf Manuals
Related Search