Santos Coffee Grinder #1
Contents
1. 220 240 V 60 Hz Line protection the machine should be connected to a standard 2 pole earth electric socket The system should be fitted with an RCD and a fuse rated at 16A The appliance must be earthed CARE e Before connecting the machine check that the mains electrical voltage is the same as the voltage for your appliance Its value is shown gt either on the identification plate under the machine gt oron the identification plate on the last page of this manual e If the power cable is damaged it should be replaced by a special assembly available from approved SANTOS dealers or from SANTOS CARE Check that the On Off switch 13 is in the 0 position before connecting the power cable plug to your mains electric power socket fig A 98101 US 3 1 10 2010 VN www santos fr RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE This equipment is marked with the selective sorting symbol relating to wastes from electrical and electronic equipment It signifies that this product should be taken over by a selective collection system conforming to the Guideline 2002 96 EC WEEE part Professional Equipment so that it can be either recycled or dismantled in order to reduce any impact on the environment For more information please contact your Retailer or the SANTOS For eliminating or recycling components of equipment please contact a specialized company or contact SANTOS The electronic products not undergoing a2. Low voltage directive No 2004 108 EC CEM directive No 2002 95 EC RoHS directive No 2002 96 EC WEEE directive The machine complies with the provisions of the following harmonised European standards EN ISO 12100 1 and 2 2004 Machine safety devices General design principles NF EN 60204 2006 Machine safety devices Machine electrical equipment General regulations EN 60335 2002 Safety of household and similar electrical appliances SIGNED IN VAULX EN VELIN ON 01 01 2010 SIGNATORY S TITLE CHIEF EXECUTIVE OFFICER SIGNATORY S NAME Aurelien FOUQUET SIGNATURE 98101 US 3 1 10 2010 VN www santos fr IMPORTANT SAFEGUARDS When using cleaning or maintaining the machine always follow these instructions Read all instructions Note You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual IMPROPER USE 1 Never operate the machine without coffee beans in the bean container 2 Do not use this machine for grinding anything other than roasted coffee beans 3 Remove from the coffee beans any foreign bodies which may damage the grindstones metal staples stones etc 4 Cleaning in a jet of water or a high pressure spray is prohibited 5 The base 11 must not be immersed in water ELECTRICAL CONNECTION e The electric power supply for the machine is available in 3 single phase voltages 110 120 V 50 60 Hz 220 240 V 50 Hz
3. friction will be heard then back one notch in the reverse direction ATTENTION This is a delicate operation and prolonged contact between the grinding wheels should be avoided since this could damage them 4 Turn the appliance off by placing switch 13 on 0 5 Without moving the button 6 place the dial 4 on the FINE position then tighten the hexagon socket screw 7 fully home 98101 US 3 1 10 2010 VN www santos fr 6 Run the machine empty to check that the grinding wheels rotate without touching each other on the finest setting If this is not the case repeat the above procedure 98101 US 3 1 10 2010 VN www santos fr FAULT FINDING Identify the exact reason the appliance stopped In every case If the problem persists switch off the power supply to the machine unplug the cord from the mains socket and call in the maintenance service or contact a SANTOS approved dealer The machine will not start e Check the mains power supply and the condition of the power supply cord e Note the switch should be lit when on the 1 position e Check that there are no foreign bodies stuck between the grinding wheels The machine stops because the motor has overheated the metal casing around the motor unit is hot Models1 10 120V 50 60Hz only In the event of overheating the motor stops The overheating protection system resets automatically wait for the motor to cool 15 to 30 minutes before restarting the
4. machine The machine stops because of an overload If the motor is blocked foreign body something too hard the excess current protection system 14 located under the appliance will be triggered automatically and cut off the electrical power to the motor e Set the On Off switch 13 to 0 position disconnect the appliance e Correct the fault then press the excess current protection button 14 e Press the On Off switch 13 position l If the problem persists check the following points e Check that the grinding wheels do not touch each other e Check the state of wear of the grinding wheels grinding too fine with worn grinding wheels can result in a motor overload like this e If there are no foreign bodies preventing the appliance from working then check and replace the motor starter relay then the capacitor 98101 US 3 1 10 2010 VN www santos fr MACHINE TECHNICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS 1 1 1PS V 220 240 100 120 220 240 Frequenc 50 50 60 60 Motor Power input 600 650 650 Speed 1500 1500 1800 1800 Average capacity Hopper capacity Grind drawer capacity Maximum bag height Dimensions Height Width Net weight Packaged weight Noise 2 Lpa incertitude K pa 2 5dB 1 These ratings are provided as a rough guide The exact electrical specifications can be found on the rating plate 2 Noise level measured with sound pressure appliance in operation 1 m f
5. selective sorting are potentially dangerous for the environment The damaging materials should be eliminated or recycled according to the regulations in force YOUR COFFEE GRINDER 1 1PS and 4 e The coffee grinder is designed especially for hotels restaurants community catering for the drawer version and for coffee roasters e The robust frame of the appliance is made of cast aluminum and painted metal The transparent hopper is made of transparent polycarbonate transparent and contains 1 kg beans o Model 1 and 1PS The appliance is usually supplied with a grind collector drawer with a capacity of 800 g But the bag grip model can also be supplied on request maximum bag depth of 150 mm o Model 4 The appliance is delivered with a bag grip system as standard maximum bag height 280 mm e A button for adjusting the fineness of the grind caters for all types of coffee grind fine grind espresso filter coffee medium or coarse grind e The special hardened steel grinding wheels O 63 5 mm guarantee a fine and even grind 98101 US 3 1 10 2010 VN www santos fr USING THE APPLIANCE ADJUSTING THE GRIND e Turn the grinding wheel gap adjuster button 6 clockwise for a coarser grind and anticlockwise for a finer grind The factory setting is for the finest grind the grinding wheels nearly touching each other SERVICING e Clean the coffee outlet the coffee bean holder and the grinding mechanism f
6. 000 7 FAULT FINDING siria ABAKA 9 The machine will not Saka aaa a tn idad tee 9 The machine stops because the motor has overheated 9 The machine stops because of an overload 9 MACHINE TECHNICAL SPECIFICATIONS incccccvsivenssatscesasovonassntensacnteretssavonseensseossassenceonssenses 10 Wiring diagram 110 120V 50 60Hz Model 1 1 PS coincide cidade 11 Wiring diagram 220 240V 50Hz Model 1 TIPS aaa AA 12 Wiring diagram 220 240V 60Hz Model 1 IPS een 13 Wiring diagram 100 120V 50 60Hz Model 4 rene 14 Wiring diagram 220 240V 50Hz Model 4 AA aie ee seen 15 Wiring diagram 220 240V 60Hz Model Po ARA RAS 16 TE UIC NG AGANG is 17 WARRANTY CERTIFICATE scssscsssssossscassoossassonssessssnssosssossssesonssssosssoossasssessonsssossassoosssessesesesossoes 20 APPLIANCE IDENTIFICATION PLATE namana AGING 20 98101 US 3 1 10 2010 VN www santos fr CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS SAS 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE HEREBY DECLARES THAT THE MACHINE DESIGNATED ON THE IDENTIFICATION PLATE AFFIXED e UNDER THE APPLIANCE e ON THE WARRANTY CERTIFICATE ON THE LAST PAGE OF THIS MANUAL COMPLIES WITH THE PROVISIONS OF THE machines DIRECTIVE n 2006 42 CE AND THE NATIONAL LEGISLATION TRANSPOSING IT IT ALSO COMPLIES WITH THE PROVISIONS OF THE FOLLOWING EUROPEAN DIRECTIVES No 2006 95 EC
7. 1 10 2010 www santos fr NX SS santos jJ ses a dica NP Ka i PANA ma GP gun x kaha THA Pata the e Pi na dns Kin a T ss 5 TA a gt PO a y By a 8 tes WU AA AA Re AA a AA mapa D oo AA AA ee wet et aa 98101 US 3 1 10 2010 www santos fr ITEM Description 1 Bean hopper cover Bean hopper Bean hopper shutter Adjusting dial Grinding wheel gap adjuster button Dial fastening screw 2 3 4 5 Adjuster button attachment 6 7 8 Bag grip cord 9 Bag grip strap 10 Grind outlet tube 11 Base 12 Non slip feet 13 On off switch 14 Thermal overload switch with reset 15 Grinding unit 16 Grinding unit clamp nut 17 Grinding wheels 18 Mobile grind wheel carrier plate 19 Fixed grind wheel carrier plate 98101 US 3 1 10 2010 ay www santos fr Y santos J WARRANTY CERTIFICATE WARRANTY This appliance is guaranteed for twelve months from the date of manufacture appearing on the identification plate The guarantee is strictly limited to the free replacement of any original part acknowledged by us as being defective as a result of a fault or a manufacturing defect and identified as belonging to the appliance in question It does nor apply to damage resulting from an installation or use which does not comply with the instructions supplied with each appliance user manual or in the event of an obvious la
8. SANTOS sas 140 150 AVENUE ROGER SALENGRO 69120 VAULX EN VELIN LYON FRANCE SANTOS TEL 33 0 472 37 35 29 FAX 33 0 478 26 58 21 FAX 33 0 478 26 58 21 E Mail santos santos fr www santos fr SHOP COFFEE GRINDER 4 COFFEE GRINDER 1 and 1PS USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept e CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE Model 1 Model PS Model 4 Coffee grinders Fruit juicers Mixers Blenders Drinks dispensers Planetary mixers Cheese graters Ice crushers Mincers Vegetable slicers Dough mixer Moulins a caf Presse fruits Mixers Blenders Distributeurs de boissons Batteurs m langeurs P trin Rapes a fromage Broyeurs a glagons Hache viande Coupe l gumes MODELES DEPOSES FRANCE ET INTERNATIONAL INTERNATIONALLY PATENTED MODELS 98101 US 3 1 10 2010 AA www santos fr CONTENTS CE COMPLIANCE DECLARATION ostia 3 IMPORTANT SAFEGUARDS 2p BAKER 4 PROPRES ae a are a 4 ELECTRICAL CONNECTION ais 4 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE 3 YOUR COFFEE GRINDER 1 IPS and 4 oooooccnocconnconocnnnonnnonaconccnncononononncconcconccnncn nono nconaronanoss 5 USING THE APPLIANCE cursan nica aerea decias 6 ADJUSTING THE GRIND A A AA AAA td 6 SERVICING A o 6 MAINTENANCE a 6 Spare Dan aca 6 Replacing th OSONA ANA ea 6 ADJUSTING THE MINIMUM GAP BETWEEN THE GRINDING WHEELS 0ccc00c0e00ee
9. ck of maintenance or non observance of basic electrical safety rules All part replacements under warranty are made after return of the defective part to our workshops carriage paid accompanied by a copy of this warranty certificate on which the serial number of the appliance is shown All appliances have an identification plate bearing a serial number identical to that on this warranty certificate In the event of serious damage which is deemed only to be repairable in our workshops and after agreement from our services all appliances under warranty are to be dispatched by the client carriage paid If the appliance is repaired outside the warranty the forwarding and return transport is the responsibility of the client Parts and labour are invoiced at the prices in force spare parts price hourly labour cost All repairs will be subject to a prior estimate which should be agreed before repair In the event of a dispute the Courts for the manufacturer s area Lyon alone have jurisdiction APPLIANCE IDENTIFICATION PLATE SPECIMEN For all documents not supplied with the appliance l l Printed Faxed and Downloaded 98101 US 3 1 10 2010 A www santos fr
10. he power supply cord 2 Close the shutter 3 on the bean hopper 2 Take off the bean hopper 2 3 Turn the grinding wheel gap adjuster button 6 clockwise until it comes to a halt at the COARSE setting 4 Unscrew the nuts 16 and remove the whole grinding unit 15 to gain access to the grinding wheels 5 Change the grinding wheels 3 fastening screws after carefully cleaning the supporting surfaces TAKE CARE The slightest small coffee particle under the grinding wheel may prevent the machine from operating correctly It is recommended that the grinder body is cleaned with a compressed air jet or a dry brush 6 Reassemble the grinding unit 15 and adjust the grinding gap to its minimum setting TAKE CARE e Before tightening the fastening nuts 16 on the grinding unit 15 check that the dial 4 of the grinding wheel adjuster button 6 is set to COARSE This precaution is essential to prevent any risk of the grinding wheels being brought too close to each other which could cause damage to the grinding unit ADJUSTING THE MINIMUM GAP BETWEEN THE GRINDING WHEELS This should be done after replacing the grinding wheels 1 Plug the appliance in and run it empty 2 Unscrew hexagon socket screw 7 on the dial 4 using a 2 mm Allen wrench Check that the dial 4 is free to rotate without turning button 6 3 Turn button 6 anticlockwise until the grinding wheels come into contact a slight sound of
11. rom time to time Always turn the appliance off switch 13 on position 0 and unplug it MAINTENANCE Before carrying out any work on the appliance it must in all cases be unplugged from the mains power supply and the motor start capacitor discharged Discharging the capacitor Use a screwdriver with insulated handle to touch the 2 connectors on the capacitor 13 The appearance of an electric arc shows that the capacitor has discharged Spare parts This machine requires no specific maintenance The bearings are lubricated for life If work is required to replace worn parts such as the grindstones or the electric or other components refer to the parts list see exploded view at the end of the manual IMPORTANT It is prohibited to use spare parts other than those certified made by SANTOS For all spare part orders see references in the exploded view at the end of the manual state gt the type gt the machine serial number and gt the electrical specifications recorded under the machine Replacing the grindstones IMPORTANT always change both 2 grindstones 17 at the same time use SANTOS reference 00001B 98101 US 3 1 10 2010 Ly www santos fr The 2 grinding wheels are identical and can be fitted equally either on the moving plate 18 moving grinding wheel or on the cast metal adjustment block 19 fixed grinding wheel 1 Stop the machine by putting the switch 13 to O and disconnect t
12. rom its centerline in accordance with standard EN 31201 98101 US 3 1 10 2010 ay www santos fr Wiring diagram 110 120V 50 60Hz Model 1 1PS Bleu Condensateur Marron Relais de demarrage Marche Arr t Noir 98101 US 3 1 10 2010 ay www santos fr Wiring diagram 220 240V 50Hz Model 1 1PS Noir Marron Condensateur Blanc Blanc Relais de demarrage Blanc H Marche Arr t 98101 US 3 1 10 2010 Ab www santos fr Wiring diagram 220 240V 60Hz Model 1 1PS Rouge Bleu Condensateur Blanc Blanc 1 Noir Relais de 4 s5 l3 demarrage Marche Arr t E gel Vert jaune J ge ME ss 98101 US 3 1 10 2010 ay www santos fr Wiring diagram 100 120V 50 60Hz Model 4 Blue Black Capacitor White Thermal overload protector Black White Green yellow see ag 98101 US 3 1 10 2010 Ab www santos fr Wiring diagram 220 240V 50Hz Model 4 Black Brown Capacitor White White Starter relay Excess current ial protector White White On Off Green Yellow ag ll ra 98101 US 3 1 10 2010 AA www santos fr Wiring diagram 220 240V 60Hz Model 4 Blue Red Capacitor White White Black a 3 Starter relay Thermal overload i protector ral White White On Off SA MUPA Green Yellow 98101 US 3 1 10 2010 ay www santos fr Figures e Model 1PS FIGURE A 98101 US 3
Download Pdf Manuals
Related Search