Home

Technical Manual (eng) - ELAN - Certification

1. 1 with a screwdriver and slide the heel until the heel cup just touches the boot Lock the length adjustment by pushing it down Latch the boot in the binding and check forward pressure again The toe pincers should not be pressed open and the indicating pointer should rest within the scribed area Pict 03 7 ADJUSTMENT Use the Boot Indicator to check and make sure that the boot meeis international standards and is not damaged AFS JUNIOR The SX Junior Line is suitable for both adult type A and children type C boots the innovative mechanical Anti Friction Slider AFS automatically adjusts to the boot sole height compensating A C standards as well as height differences due to icing up dirt or boot wear Pict 05 C CHILDREN A ADULT If you want to increase the stability of your junior binding in combination with children type C boots e g for junior racing you can replace the standard AFS with a vertically blocked AFS Art No 162962 which is for children type C boots ONLY All you have to do is to separate the standard slider from the base plate Pict 06 Afterwards you can simply click in the spare slider Pict 07 ADJUSTING THE RELEASE VALUES The release values of the toe and heel should be determined by height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws at heel and toe unit ELAN recommends adjusting these settings with a manual screwdr
2. Technical Manual Take at least one reference boot satisfying all standards and free of functional damages to perform test adjustments with the binding 6 1 USING THE SINGLE CODE Adjust toe and heel to the corresponding alpha setting SINGLE CODE of the ski boot Pict 04 IF A BOOT OF UNKNOWN SIZE IS USED PROCEED AS FOLLOWS Place the boot in the toe cup Slide the heel piece forward until it just touches the boot Close the binding and check the forward pressure 6 2 ADJUSTING THE RELEASE VALUES The release values of the toe and heel should be determined by height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws at heel and toe unit ELAN recommends adjusting these settings with a manual screwdriver Do NOT use a screw shooter We also recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US NOTE Release retention settings above a release moment of 100Nm at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skiers own risk 7 FUNCTION CHECK Before the newly mounted ski equipment is exposed for rental use please perform a complete functional check NOTE In some countries USA rental equipment has to pass a Pre Season Test See the Rental section of this manual EASY ENTRY AND EXIT If set properly the boot should not catch on t
3. acting for the ultimate user and that will provide this form and all other warnings and information to the ultimate user understand and agree that skiing snowboarding ski boarding and related activities are HAZARDOUS and that injuries are common and ordinary occurrences during these activities AGREE TO ASSUME ALL RISKS OF INJURY OR DEATH which may result from these activities Please Initial If Alpine ski equipment or skiboards are beeing furnished understand that the ski boot bind ing system will release the boot from the ski when certain forces on system reach preset val ues but that it will NOT RELEASE OR RETAIN at all times where release or retention may prevent injury and that it CANNOT prevent all injuries or guarantee the user s safety l under stand and agree that unwanted release or retention of bindings is an inherent risk of using any ski boot binding system further agree and understand that any ski boot binding system does NOT ELIMINATE THE RISK of injuries to the user s knees or to any other part of this user s body If Nordic or Snowboard equipment is being furnished understand that these systems normally will NOT RELEASE in falls and accidents and that they do NOT PROTECT against any type of injury To the fullest extent allowed by law hereby RELEASE this ski shop and all manufacturers and distributors of this equipment from ANY AND ALL RESPONSIBILITY OR LEGAL LIABILITY for any injuries damages o
4. for a boot to qualify before getting eliminated from inventory 1 Clean the boot s to be tested with soap and water Allow to dry 2 Select an appropriate ELAN reference binding that has displayed release values within the inspection tolerance on the ELAN Adjustment Chart Clean the binding s boot contact surfaces with soap and water and allow drying 3 Test the binding and boot in Twist and Forward Lean at a mid scale indicator value Only one direction of twist is required 4 Ina further test run lubricate all boot binding contact areas with soapy water Retest in Twist and Forward Lean 5 Results of each lubricated test should be within 20 of the corresponding results when tested clean Any boot which fails this test should not be used with an ELAN binding elam s Maintenance amp Service 1 VISUAL INSPECTION OF BINDING In assembling a system for the skier it is the responsibility of the shop to inspect and evaluate each equipment component This inspection checklist should be followed before any mounting or adjusting is performed Ideally they should be posted and used on the sales floor while the customer is still in the shop so that any deficiencies can be explained on the spot 2 CHECK SUITABILITY e Isthebinding model appropriate for the skier s ability e The binding must be compatible with the customers boot ski e The skier s release retention setting should fall within the binding s adju
5. lt 140cm Jett lt 140cm Starr lt 140cm Maxx lt 140cm RC Race lt 140cm Sky lt 140cm Pinball PRO Team lt 140cm Petit lt 140cm 3 MOUNTING POSITIONS The mounting position is usually close to the gravity point of the ski Any variation towards the tip will make the ski more aggressive and quicker to turn any variation towards the tail will make it accelerate better out of turn 4 MOUNTING POSITIONS FOR SKIS This measurements should be taken from the tail of the ski and indicate the boot center All measurements are in millimeters Acceptable tolerance 1 5mm 13 6 x 9 0 mm TRIGLAV 2 component glue Mounting Positions for Models 2015 16 195 GSX FIS Mounting pos 780 Length 165 SLX FIS Mounting pos 20 820 210 211 bis po pe y 95 y bo 6 0 692 Mounting pos 745 length por po Mounting pos 870 880 Mounting pos 205 890 DO A je 595 663 218 920 730 780 m Mounting pos p joe o 80 Mounting pos 531 688 y o Length 150 158 Mounting pos 514 540 RCS 558 RCX SLX SL Mounting pos SLX WaveFlex Mounting pos SLR WaveFlex Mounting pos 00 B ALL MOUMTAIN AMPHIBIO Lengt 00 CA Amphibio76 11 10 9 M pos fi NI 00 NJ Po 0 01 al Ojo li O Ch Pet kk L MOUMTAIN aveflex 72 9 Alaska PRO Mounting pos 1 e lt lt O
6. no warranty action will be taken on release value related claims unless this report accompanies the returned bindings Distributor addresses Alpina Sports Corp 93 Etna Rd Lebanon NH 03766 USA Toll Free 1 800 425 7462 Phone 1 603 448 3101 Fax 1 603 448 1586 ELAN Sports Inc 81 H Brunswick Blvd Dollar des Ormeaux QC H9B 2J5 Canada Toll Free 1 800 361 7860 Phone 1 514 421 7871 Fax 1 514 421 7394 Risk Management Indemnification Insurance and your liabilities INDEMNIFICATION Indemnification simplv means that someone agrees to reimburse you for certain costs In the ski industry it normallv means that provided you fully follow the manu facturer s requirements and install and adjust the binding system correctly the manufacturer or distributor will provide a defense and pay any judgment which may be entered against you if you are the subject of a claim or suit by a customer who claims to have suffered bodily injury as a result of using certain equipment The key here is you must be able to prove you properly performed the service and properly represented the product If you do not you will not be entitled to a defense or indemnification in the event of a claim YOUR PERSONAL LIABILITY lts simple If you make a mistake which causes harm to another you can be held liable for it Be very careful not to make verbal warranties that extend beyond those made by ELAN Read the manufacturer
7. 15 16 17 18 19 20 Brake pedal Brake arms Heel lever Heel cover Sole lug Visual indicator Heel housing Adjustment screw Single Code scale ONE TOUCH lever Data Binding Line Rental 2015 16 ESP 10 0 vellos from 26 kg from 18 to 84 kg from 10 to 48 kg from 26 kg 9 from 57 Ibs from 39 to 187 Ibs from 22 to 105 Ibs from 57 Ibs Toe svstem Full Diagonal Full Diagonal Full Diagonal Full Diagonal Heel tvpe RENT OT RENT OT SX Kid RENT OT NO Brake Power Brake SX Kid Power Brake GE LD 78 Brake 74 LD 78 Length adjustment 263 mm 215 mm 191 mm 263 mm range to 391 mm to 343 mm to 294 mm to 351 mm Set weight 2570 9 2450 y 1630 g 21409 A adult Boot sole type A adult A adult Children A adult Drill template SP2003 W SP 2003 W SP 2003 W SR 2003 W Advusment vellow bushing white bushing red bushing Yellow bushing ESP 7 5 AC Binding Track Plates compatibilitv New ESP 7 5 AC binding supports both boot norms Adult and Children ESP 7 5 only Adult norm New Track plates have extended boot sole range from 215 to 343 mm compared to the old Track plate only from 263 to 323 to cover smallest children boot sizes Therefore the combination between the old ESP 7 5 binding and the new Track plate with the scale 215 343mm is NOT allowed ESP 7 5 Art No 140348 140349 141094 141164 141165 141276 141277 OLD ESP7 5 BD 83 20 12 000 NEW ESP7 5 AC DD832113000 from season y r a o OLD BSL 263 343mm Rent
8. 3 ATTACK 16 AND 13 BINDINGS 5 3 1 MOUNTING ATTACK 16 AND 13 For mounting the toe unit at ATTACK 16 and 13 bindings If the tester is not moveable the gap is smaller than 0 5 mm if place the mounting part over the front 2 predrilled holes and you feel no resistance the gap oa than peo a tighten the screws Now slide the toe unit from the rear over In both cases you need to re adjust the AFD Pict 19 the mounting part and fasten the screws Go on by mounting the heel unit Hook the brake into heel housing and place the heel unit over the predrilled holes and tighten the screws in a cross pattern Pict 15 elam x lt 1 Smm 6 FORWARD PRESSURE Make sure that the boot meets international standards and is not damaged Place the boot in the binding and close it The indicating pointer should rest within the scribed area Pict 20 if not you have to adjust the forward pressure DON T OPEN THE LENGTH ADJUSTMENT LOCK AS LONG AS A SKI BOOT IS FIXED IN THE BINDING Place the ski boot in the open binding and rest the boot heel on the brake pedal Lift the length adjustment lock with a screwdriver and slide the heel until the heel cup just touches the boot Lock the length adjustment by pushing it down Latch the boot in the binding and check forward pressure again The toe pincers should not be pressed open and the indicating pointer should rest within the scribed area Pict 20 7 ADJUSTING THE RELEASE VALUES The relea
9. ENE My ft in Nm Nm H k Ibs 10 13 kg 22 29 Ibs 14 17 kg 30 38 Ibs 18 21 kg 39 47 Ibs 22 25 kg 48 56 Ibs 26 30 kg 57 66 Ibs 31 35 kg 67 78 Ibs 36 41 kg 79 91 Ibs 42 48 kg lt 148 cm 92 107 Ibs lt 4 10 49 57 kg 149 157 cm 108 125 Ibs 411 5 1 58 66 kg 158 166 cm 126 147 Ibs 5 2 5 5 67 78 kg 167 178 cm 148 174 Ibs 56 5 10 79 94 kg 179 194 cm 175 209 Ibs 511 6 4 BE N q N N a N a N N l N dr y a y a GA N gt 95 kg gt 195 cm 210 Ibs 6 5 PrE 2 N N a N O O O N 1 00 a Lowermost tolerance limit b Uppermost tolerance limit 137 588 HOW TO USE THE RELEASE RETENTION ADJUSTMENT TABLE Determine the Skier Code by locating the skier s weightin 3 Find the column that corresponds to the skier s boot the first column and the skier s height in the second sole measurement in millimeters column If the height and weight are not on the same line The value where the Skier Code and the boot sole select the Skier Code closer to the top of the chart measurement intersect is the initial indicator setting for The Skier Code found in step 1 is for Type skiers For the skier Type Il skiers move down the chart toward the bottom one If the intersection of the row and column falls in a blank Skier Code For Type III skiers move down two Skier b
10. FUSION EL 10 0 TMD ELW 9 0 TMD Jr EL 7 5 TMD Jr EL 4 5 TMD Jr EFR 15 0 Wide ELX 14 0 ELX 14 0 Wide ELW 11 0 Wide EL 10 0 EL 7 5 ELC 7 0 EL 4 5 ELN 10 0 ELN 7 0 ELN 4 5 ESP 13 0 ESP 10 0 ESP 7 5 ESP 4 5 Season 09 10 ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION Wide ELX 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 11 0 FUSION ELW 9 0 FUSION EL 10 0 TMD ELW 9 0 TMD Jr EL 7 5 TMD QUICK TRICK EL 4 5 TMD QUICK TRICK EFR FS 18 0 XFAT EFS 14 0 Wide ELX 14 0 ELW 11 0 Wide EL 10 0 EL 7 5 ELC 7 0 EL 4 5 ESP 13 0 ESP 10 0 ESP 7 5 ESP 4 5 Season 10 11 ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION Wide ELX 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 11 0 FUSION ELW 9 0 FUSION Lady EL 10 0 TMD EL 10 0 QT ELW 9 0 TMD Jr ELW 9 0 QT Jr EL 7 5 QT Jr EL 4 5 QT Jr EFR FS 18 0 XFAT EFS 15 0 Wide EFS 14 0 Wide ELX 14 0 ELW 11 0 Wide EL 10 0 EL 7 5 ELC 7 0 EL 4 5 ESP 13 0 ESP 10 0 ESP 7 5 ESP 4 5 ESR 10 0 Season 11 12 ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 ER 11 0 Wide ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION Wide ELX 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 11 0 FUSION ELW 9 0 FUSION EL 10 0 TMD EL 10 0 QT ELW 9 0 TMD Jr ELW 9 0 QT Jr EL 7 5 QT Jr EL 7 5 QT Jr Wide EL 4 5 QT Jr EL 4 5 QT Jr Wide EFR FS 18 0 XFAT EFS 15 0 Wide ELX 14 0 ELW 11
11. H 82 HT IMVHA IS M v8 IXVHS GIM XS V 0 L Od 30VH Z MVHY HIMOd y 98 81 OHd JOVH Z MVHY HIMOd 5 GLL TS 2MVHY TIVYHZMOd M tz IMVHA GIM XS V OLL Odd JOVH ZIMVHA HIMOd V 82 21 OHd JOVH ZIMVHY HIMOd 5 06 IS IXVH9 IIVHHIAMOd 1 ve yl 2MVHY QIM XS y 96 OHd 4OVH STE HIMOd 9 y 38 91 Odd JOVH ZAMVHE HIMOd gt 9 82 1S 3XvHg TIIVHHIMOd 92 HT INV A xs W swelb UI JUDISOM 184701 oost 000b OOSE 000 00Sc 000c 00GIL 0001 00G 0 0 KA o o S Li JI i MI Ir NI KI c A l OL 08 06 ww ul JU DISH PUEJS eJOL 6 Boot Handling and Testing 1 VISUAL INSPECTION OF SKIBOOTS In assembling a system for the skier it is the responsibility of the shop to inspect and evaluate each equipment component This inspection checklist should be followed before any mounting or adjusting is performed Ideally they should be posted and used on the sales floor while the customer is still in the shop so that any deficiencies can be explained on the spot In retail boots must pass all four points of this inspection before being accepted for use In rental this inspection is the first step in the preseason boot test procedure 1 1 CHECK TYPE SIZE AND OVERALL CONDITIONS e ls the performance level appropriate for the skier e Is the size correct SINGLE CODE boot sole length e s all hardware intact and in working order e ls the boot free of excessive or asymmetric wear e Is the bo
12. Incorrect or off center mounting Check the template Remount using template correctly Improper use of testing device Check calibration and operating technique Adult boot sole does not fit into Boot sole exceeds the standard Clean AFD and boot sole check Junior toe lug tolerance standard tolerance change boot RACE PRO or POWERRAIL heel Heel glide inserts worn Remove heel and replace plastic heel wobbles in the track guides 74 Heel slides backwards when customer steps in CLASSIFY YOURSELF DETERMINING YOUR SKIER TYPE IS YOUR RESPONSIBILITY Your Skier Type height weight age and boot sole length are used by the shop technician to determine the release retention settings for your bindings Consult these descriptions to select your classification Be sure to provide accurate information Errors increase your risk of injury Skiers not classified as Types I or IIL TYPE I Cautious skiing on smooth slopes of gentle to moderate pitch pitch Fast skiing on slopes of moderate to steep Skiers who designate themselves as Type receive lower than average release retention settings This corresponds to an increased risk of inadvertent binding release in order to gain releasability in a fall This type also applies to entry level skiers uncertain of their classification Skiers who designate themselves as Type Il receive average release retention settings appropriate for most recreational skiing Skiers who designat
13. Inspection Range one value above to one value below the reference value the unit passes If the results are outside Inspection Range but within the In Use Range two values above to two values below the reference value count the unit as a Class Deviation If the results are outside the In Use Range count the unit as a Class II Deviation Check elastic travel and visually inspect the ski brake function interface areas between boot and binding including AFD lug height adjustment if appropriate and forward pressure Count any deficiencies as Class Deviations If more than the maximum number of Class Deviations given in Table B are found in the sample or a single Class II Deviation is detected the sample fails and daily sampling must be conducted until the problem which led to the failed sample is found and corrected See page 74 for Trouble shooting Procedures following a Failed In season Inspection Record the date the sample was tested the number of units tested the number of Class and Class II Deviations whether the sample passed or failed and any actions taken There is no need to record the identity of units tested or actual Test Results Inventory size pairs Inventory size units half pairs Sample Size units half pairs Max class 1dev Table B Sample Size RENTAL DEMO OF PARTIAL SYSTEMS Many shops rent their customers partial ski equipment systems Boois only
14. Insurance Te FIS COMMENTS REFERRED BY A TECHNICIANS SIGNATURE DREES have read understood and agreed to all terms and condition on the reverse side of this form accept full financial responsibility for the equipment listed on this form and promise to return it clean and undamaged by the agreed time and date If fail to do so agree to pay for its repair cleaning or replacement at the full retail rate as determined by the shop as well as for the rental value of any additional days For release bindings only have confirmed that the binding release retention setting numbers on the bindings correspond to the Final Indicator Setting stated on this form understand that correct weight height age and skier type are essential to proper adjustment of the release retention settings and certify that all user information on this form is correct A SIGNATURE OF USER OR AGENT DATE A PARENT S SIGNATURE IF USER IS A MINOR DATE 94 WARNING LIABILITY RELEASE INDEMNITY AGREEMENT AND ASSUMPTION OF RISK AGREEMENT PLEASE READ CAREFULLY ASSUMPTION OF RISKS understand how this eguipment works and have received proper instruction and satisfac tory answers to any questions If at any time this equipment does not seem to be working properly will stop using it immediately and retum it for inspection and possible repair or adjustment If this equipment is to be used by someone other than me certify that am
15. Skiers should make a visual inspection of their system before each use including the AFD pad which should be checked for wear damage or loss It is also wise to visually verify the release indicator value NOTE e Theworkshop ticket must be read initialed and signed by the customer If the customer is a minor his or her signature should be obtained along with that of the parent or guardian If a parent or guardian is not available the equipment should only be released if the proper signatures have been obtained e Remember the customer s signature is required in two places under the terms of the ELAN Retailer Indemnity Program In order to avoid misunderstandings with the customer please inform them of this requirement when equipment is taken in for service e If the customer is not the end user every attempt should be made to make certain all aspects of the system are explained to the user and to obtain his her signature on the workshop ticket ABOUT TESTING Testing is required for all ELAN retail and rental systems as specified in this manual Many consumers view system testing as a valuable service provided by professional shops They expect their equipment will be properly tested and are willing to pay for it On the other hand some customers may be reluctant to accept any additional costs They may be especially resistant to charges made by the shop for testing and inspections of equipment which is being serviced Fol
16. T ADULT ADULT ADULT ADULT ADULT A T 270 330 300 360 R Powerrail LD all width Adrenalin LA 9 9 17 17 17 23 0 21 0 8 2390 g 2420 g 2080 g 1830 g 1800 g 2250 g 1360 g 1830 g Adrenalin 92 W FAT 92 W FAT 92 W FAT Attack demo 92 W FAT Ambition R Powerrail LD all width RACE PRO IPB RACE PRO all width RACE PRO IPB RACE PRO all width PB RACE PRO all width RACE OT PB LD all width X SL BRAKE FS all width 32 8 424 LA as 257 es 1 5 3 A 10 5 2 2 32 32 32 NO Wu 5 5 7 5 7 7 7 5 5 5 5 5 5 5 5 5 5 5 5 5 4 127 E E 209 386 L Ga 260 350 Em ss Ambition all width C 90 14 IM MO SL Junior Brake 72 SX Kid Brake 74 21 SX Junior 15 32 8 24 32 8 24 A C A C 92 W FAT 94 W 1400 g 1190 g J K Weight without Brake Ski Boot Norm QuickTrick Snap IN scales QuickTrick TMD scales A C Adult Children XSS 195 263 mm S 199 283 mm A T Adult Touring SM 225 293 mm M 239 323 mm ML 255 323 mm L 263 347 mm elam z Parts Reference Chart RENTAL ESP 10 0 TOE PIECE 1 2 3 A 5 6 7 8 9 1 28 Adjustment screw Visual indicator ABS Color coded base plate AFD Teflon Toe cover ONE TOUCH lever Base Plate Bar Code area 0 Single Code scale ESP 7 5 ESR 10 0 HEEL PIECE 11 12 13 14
17. The middle quantitative value of 3 releases in each direction should be used as the test result 4 Compare Twist and Forward Lean test results with the System Inspection Ranges on the actual ELAN Adjustment Chart 5 If any test results fall outside the System Inspection Range consult ELAN Troubleshooting Procedures which follow this section 6 With testing complete the ELAN Certified Mechanic must complete and sign the workshop ticket Be sure the Final Indicator Settings are correctly shown there The workshop ticket should simply reflect that the system has passed all tests or that all manufacturers procedures have been completed 5 REPLACING THE BRAKE If the brake feels too hard or blocks during the hand test if the brake arms are damaged if the pedal is worn out or if a wider brake is necessary then the brake should be replaced immediately 70 ELAN offers different brakes for almost every binding Refer to the brake line on page 33 for brake and binding compatibility To change the brake all you have to do is to unscrew the old brake and replace it with the proper brake previously selected for the binding In order to fix the brake tighten the screws On most FUSION and QUICKTRICK bindings the brake is hooked into the heel housing and not fixed with screws Slide the heel off from the rails and replace the brake Pict 01 6 REPLACING THE GLIDE INSERTS FUSION and QUICKTRICK BINDINGS To provid
18. best training An ideal task that can be incorporated into the training is preseason testing This will give your trainees hands on experience operating a testing device and adjusting ski boot binding systems Other tasks such as routine rental maintenance can also be done during the training period SHOP REQUIREMENTS Each retail location must have e A current ELAN Authorized Retailer Agreement on file with Alpina Sports Corp USA ELAN Sports Inc CANADA e A current ELAN Binding Indemnification Agreement on file with Alpina Sports Corp USA ELAN Sports Inc CANADA e Atleast one ELAN Certified Technician employed per location e The required equipment for installing and testing ELAN bindings All Agreements and Certifications must be valid for the current season SERVICE SHOP TOOLS This list is the bare minimum a shop can survive with e Tape Measure e ELAN Tyrolia Templates Drill template 92 W or FAT Blue Drill template AMBITION Brown Drill template ADRENALIN White Drill template ATTACK DEMO Turquoise Drill template 94 W Violet Drill template RACEPLATE 09 Black Drill template SP 2003 W or FAT Red Drill template SR 2003 W Yellow e Variable speed reversible electric drill e Step Drill Bits 4 1 x 9 0 mm 4 1 x 7 0 mm 3 5 x 9 0 mm 3 5 x 7 0 mm 82 e Tap Tap Brace and Tap Guide e Pozidrive No 3 screwdriver e Large slot screwdriver e Current ELAN retention releas
19. black one in From nowon the mounting is the same in both version RETAIL and RENTAL Start with the Adjustment of the telescopic tube to the closest mounting position and fix it with the screw de 85 LE 18 18 13 Close the ascender lock and slide the binding into the closed position Pict 11 Place the toe unit assembly over the front holes and fasten the two front screws Pict 12 Open the ascender lock and tighten the other two screws of the toe unit Pict 13 ATTENTION AMBITION binding are delivered without brakes Please choose the proper brake width for your ski and mount it on the binding You can also use it to ride and hike with the appropriate powder straps It is required to use one of these options refer to ISO 11088 163003 Brake AMBITION 85 C 1 pair 163016 Brake AMBITION 95 C 1 pair 163004 Brake AMBITION 105 C 1 pair 163005 Brake AMBITION 125 C 1 pair 162981 AAA Series Powder Strap 1 pair 4 4 MOUNTING OF THE BRAKES Remove the heel base plate therefore remove both screws completely Pop out the plate with a flat screwdriver 8 Take the AMBITION brake arm press it together and clap the brake pedal to a horizontal position First click right then left side into place ax A l N YN Check the right position of the brake Pict 16 Place the brake to its position on the heel unit push the plate to lock on binding Fix the plate w
20. boots TYPE A Please stay in the marked range area Pict 10 MIN Go on with placing the toe track over the holes and fasten all screws in a cross pattern Open the one touch lever and slide the toe unit from the front on the track and lock it at the appropriate boot sole marking Turning the adjustment screw at the toe moves the AFS up or down Place the tester on the AFS and enter the boot in the binding Lift the tip of the boot to take out the play of the toe Adjust the AFS with the screw in the front so that the tester is still moveable but with a slight resistance 1 PULL Now you can mount the heel unit Don t forget to add the separate white base plate otherwise you will damage the ski Hook the brake into the heel track and place the base plate and the heel track over the holes and fasten all 4 screws in a In this case you reach a gap of 0 5mm between AFS and the cross pattern boot If the tester is not moveable the gap is smaller than 0 5 mm if you feel no resistance the gap is more than 0 5mm In both cases you need to re adjust the AFS Pict 13 50 Cy gt 0 5mm V bi l A NOT OK 6 FORWARD PRESSURE Check the forward pressure by placing a boot into the bin ding If you have followed all mounting steps correctly the indicator should rest in the marked area 4 If you have too much or not enough forward pressure check the settings and
21. c 5 O D e o 01 ooo fo im Mounting pos 800 Mounting pos Mounting pos Po CD sm be e e a po po e Zest all models 640 665 700 TWILIGHT Series Leg Juo fue iso 152 os a Formu nb Team enger 500 ber ker ba e en be ks Je Lem ha Je oo fo qo o RENTAL Junior jem fo fo Jo foo no io o o fiso Ear Pro Wemgr 800 350 400 e 500 545 595 Je 680 Explore Pro hour pos e14 Joss laos e 500 545 e es e SHORTSKIS Lem o e ds o Elar 11 Instructions amp Product Warranty For the proper performance storage and maintenance of your ski you must carefully read the following instructions Each and every ski needs to be tuned properly and regularly to maintain its performance and safety Tuning is done on industrial machinery and cannot be copied manually Only certified ELAN ski mechanics with knowledge about the handling of service machines should service the skis set and adjust skis with the correct tools perform proper binding installation and explain the use and the maintenance of your ski system The Elan skis should only be used with bindings and boots that conform to accepted international standards Bindings should be mounted adjusted and maintained only by certified ELAN ski mechanics in accordance with the manufacturer s specifications Proper binding installation is essential for the optimal performance of the product Improp
22. carry or work on regularly e Copies of the manufacturer s customer instruction booklets e Technician employment applications Make sure they have the address of someone who will always know where they can be found e This can be invaluable if you need the technican as a witness e Alistingofall technician certifications and their dates Keep all certification records as well e Copies of any pertinent wall charts customer information posters etc 88 e Acopy of your shop procedures including training materials rental and repair shop practices and binding setting charts e Copies of rental fleet test data This type of supporting documentation can be tremendously useful for your lawyer STORAGE OF FORMS All forms containing the customer s signature must be kept for a minimum of five years or the term of the statute of limitations in the state where the injury occurs or your state whichever is longer As a practical matter you have no idea where or when your customer may sustain an injury on this equipment Naturally should an injury occur keep the original form ina safe place until any claims are completely resolved Risk Management is really just common sense Do your job well have integrity keep your customers well informed and keep proper records Follow these simple suggestions and you will limit the likelinood of problems Use of Non Recommended Settings SKIERS REQUESTING SETTINGS NOT RECOMMENDED
23. handles and ensure that the template Is evenly seated against the ski s top surface Attack demo A Paper Template Art No 163015 AAAAAAARARAN Drill Template Art No 163009 2 2 PAPER TEMPLATE Align the boot midsole indicator with the midsole mounting mark on the ski Fix it with a sticky tape and ensure that the template is centered and evenly seated against the ski s top surface After that you can mark the indicators 8x with a punch and remove the paper template from the ski surface Pict 02 3 DRILLING THE HOLES If not otherwise specified by the ski manufacturer use a O 4 1 x 9mm drill bit for all holes 8x for the toe and the heel track After drilling place a drop of glue into the holes It lubricates the screws and seals the holes Ff elam sw 4 MOUNTING Now open the one touch lever and slide the heel unit from the back to the track and lock it at the appropriate boot sole marking First of all make sure that the boot is satisfying the international standards and has no functional damage Determine the boot sole length with the rental caliper A No 162 617 emm oO _ 5 SOLE HEIGHT ADJUSTMENT For proper function the height of the AFS must be adjusted to the height of the boot sole ELAN recommends using the BOOT HEIGHT ADJUSTMENT TESTER A No 162 983 to get the ideal distance of 0 5mm between boot and AFS Use Attack Demo bindings only with Alpine
24. if necessary re adjust the heel Then close the lever and check the forward pressure again Now it should be okay 7 ADJUSTMENT OF THE RELEASE VALUES The release values of the toe and heel should be determined by height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws at heel and toe unit ELAN recommends adjusting these settings by hand with a manual screwdriver We also recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US NOTE Release Retention settings above a release moment of 100Nm at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skier s own risk 8 FUNCTION CHECK Check the function of the heel Make sure that the boot does not catch on the heel during entry and exit Check the brake function by pressing down the brake pedal 1 by hand The brake arms 2 must open to the braking position when the brake pedal is released D e NN Ao d ae A E 7 4 p 2 eo gt ae i le Check the elasticity and retention of the toe by pushing the boot inward and outward The binding must re center the boot easily and quickly from a 15mm lateral displacement 9 FINAL CHECK e ls the proper mounting point selected e ls the Brake mounted e Functional brake test passed e Are all screws fastene
25. is new or used sort the sample by sole type and length according to the EleM 10 20mm Sole Length Categories defined by the Release Retention Adjustment Chart In each Sole Length Category rank the boots by sole length and select the middle boot In each Sole Length Category fit the appropriate reference bindings to this typical boot and adjust the two bindings to release as close as practical to the Reference Torque in Table A Use the Reference Torque corresponding to Skier Code L for the Adult binding J for Junior binding and E for the Child binding Rinse the lubricant from one binding and mark it clean Mark the other lubricated Test each boot in the Sole Length Category with the clean Reference Binding and then the lubricated Reference Binding in both twist and forward lean only one direction in twist is required for the clean binding Set aside any boots for which the lubricated Test Result is more than 20 less than the clean Test Result in the same direction of release or the lubricated Test Result in any direction of release is outside of the Inspection Range provided in Table A for Skier Code used to set up the Reference Binding L J or F Repeat the visual check on all boois that have been sei aside correct any defects noted and retest Remove from inventorv boots that fail the retest Check all other boots from the same cell make model year and shell size as those t
26. of ELAN bindings 3 Boottoe bottom Excessive wear is indicated if the lower edge of the front surface is at or above the bottom step on the appropriate child C 2 or adult A 2 post see Pict 04 4 Boot toe ledge height With the toe stop against the boot toe the level of the toe ledge should be at or above the top of the appropriate post Child C 1 or Adult A1 see Pict 04 Replace toe pads if worn A1 5 Heel height and wear Check this boot standard with the same procedure used for the toe The heel posts A 3 C 3 are located at the rear of the device see Pict 05 6 The marks A C help to select a Child boot from an Adult by indicating the standardized sole width A3 7 C3 AJC NOTE Any boot which passes points 3 4 and 5 as well as conforming to the Visual Inspection Checklist may be accepted for use with ELAN bindings Boots which fail any point should be repaired or replaced These checks apply only to boots used with ELAN bindings Consult other binding manufacturers for their used boot specifications 3 CLEAN VS LUBRICATED SKI BOOT TEST This test is designed to determine the influence of a given boot on the release characteristic of a binding It should be performed on boots not meeting all the points of the ELAN boot visual inspection criteria or if measured release values fall outside the system inspection tolerance It is seen as the last chance
27. part Screw Set Attack Demo G3 amp G4 6mm Art No 163024 Drill template Attack Demo can be used for ski widths from 75 to 125mm For other ski widths please use the template adapter set Art No 162569 With this adapter set skis from 61 to 149mm can be mounted NOTE ELAN offers different types of brakes Refer to the brake overview on page 33 for brake and binding compatibility The description of the brakes always includes a number and a color letter code This number stands for the maximum ski width in the brake area and not in the ski center The color letter code defines the brake segment For ATTACK Demo bindings all brakes of segment D are compatible for use 2 POSITIONING OF THE TEMPLATE There are two ways to mount Attack Demo bindings Either with the solid jig A No 163 009 or with the paper template this is included in the packaging of each binding and also available as a spare part A No 163 015 We will show both procedures 255 378 AAA ttack demo 277279 A Designed in Vororbarg Austrio NOTE Keep in mind that some ski manufacturers do not use the center of boot sole location method Always follow the ski manufacturer s instructions 2 1 DRILL TEMPLATE Open the clamping jaws 2 by rotating the clamping handles 1 and then place the template on the ski Align the boot midsole indicator 3 for the appropriate boot sole length with the midsole mounting mark on the ski Release the
28. performance alpine ski bindings in this brand new Alpine Touring binding ALPINE TOURING HEEL AND CLIMBING AID The newly designed climbing aid is positioned as close as possible to the Alpine Touring AT Heel This provides better walking balance and efforiless climbing in all situations The low stand height of 38 mm improves stability and offers a confident stance With four different climbing aid positions climbing in a 0 5 10 or 15 position it is possible to adapt on different terrains without stepping out of the binding It does not matter if it is a walk through flat terrain or a steep slope up to the summit Simply use the ski pole in order to change the climbing aid position and also to lock for the downhill ride BRAKES amp INDIVIDUALITY Considering the different ski widths the ELAN AMBITION comes without brakes This gives you the opportunity to either choose the perfect fitting brake out of four different widths 85 mm 95 mm 105 mm 125 mm or simply to ride and hike without brakes using appropriate powder straps AMBITION Brakes DEMO AND RENTAL SUITABLE 85 mm Art No 163003 1 Pair In order to offer ambitious sportsmen an 95 mm Art No 163016 1 Pair opportunity to widen their horizons the 105 mm Art No 163004 1 Pair ELAN AMBITION is also demo and rental 125 mm Art No 163005 1 Pair suitable Combined with a spare demo track Art No 163001 AMBITION Demo Track 1 Pair this b
29. power transmission perfect power link between boot and binding 30 better centering accuracy than conventional cams ABS SYSTEM SAFETY Release without any friction significantly reduces strain on ligaments in forward twisting falls Perfect release regardless of temperature boot wear icing up or dirt on the binding CONVENIENCE Self cleaning design and maintenance free PERFORMANCE Best results in independent safety testing and awarded with the TUV high quality mark DIAGONAL TOE Full Diagonal Toes feature 180 release action from horizontal to vertical Maximum safety in backward twisting fall situations Race Diagonal Toes are tuned for racing purposes Due to higher release force vertically than horizontally it holds up to the high backward lean forces occurring in racing K to the new FIS regulations This gave us tt opportunity to redesign the heel track b making it 1 mm higher and 8 mm wider for gt even more stability and direct power transmission Moreover increased size of the gliding inserts reduces friction and provides even smoother and more consistent release performance in all skiing situations 23 Parts Reference Chart RETAIL ER 16 0 FreeFlex PRO TOE PIECE Adjustment screw Visual indicator ABS AFS AFD Teflon Toe cover Wings ALE aS 24 EFS 10 0 EL 4 5 HEEL PIECE Brake pedal Brake arms Heel lever Heel cover Sole l
30. s literature and warranties carefully If a feature or benefit is not mentioned there it is not offered by the manufacturer SHOP LIABILITY INSURANCE No indemnification program is a substitute for liability insurance Common sense dictates that you should have an insurance policy that covers your shop and employees for commercial general liability and completed operations Check with your insurance broker SHOP PROCEDURES TO REDUCE LEGAL EXPOSURE Risk Management has become a very important area in virtually every industry In today s world it is more impotant than ever to do as much as possible to recognize how and where we might be exposing ourselves to a potentially serious problem If these procedures are followed properly both the skier and the industry are well served In the event of a mishap the programs documentation and record keeping system will provide strong evidence of work performed YOUR OBLIGATIONS UNDER THE ELAN RETAILER INDEMNIFICATION PROGRAM Selecting equipment for your customer e Make sure the products are suitable for the skiers height weight shoe size and level of ability e Always make sure your recommendations are consistent with the manufacturer s product description representation and specifications BINDING SELECTION Generally the idea that top of the line products offer the greatest margins for safety as well as performance and durability is correct provided the skier fits the
31. skiers 2 Adhering to these guidelines may help to reduce the risk of injuries resulting from improper release retention setting selection However skiing involves inherent risks Injury can result from simply falling down impact with an object or from many other actions Many injuries are unrelated to the function of the release system Furthermore even a properly adjusted binding cannot protect the skier in all situations 3 Difficulties with release or retention may be unrelated to release retention settings and can result from your skiing style the incompatibility of your boots and bindings or wear damage or contamination of a component of the release system Be sure to describe your circumstances to the shop technician and to authorize recommended inspections and repairs before proceeding 4 If you have been dissatisfied with the release retention settings that result from your normal skier classification you may wish to consider changing your skier classification or designating skier type classifications that are different for twist and forward lean You may even request discretionary release retention settings that are outside of your setting range If you believe that you require higher release retention settings but are unsure if the increase should be applied to twist or forward lean settings request that the increase be applied to forward lean settings before experimenting with higher twist settings Similarly if you
32. spare parts in detail text and pictures and shows the appropriate article A AAA ES os Fo Or fe fu 6740 E I spanepanTS ER 16 0 FF EVO RO BRES A M BK FLU GA Ae Pair number description and order quantity AAS bg mm Power Drake Race PRO 150 AJ 1 4 IGJ Ser 5 5 x 16 0 Hen 50 Per 1 15 Colored bars and marks of the reguested part make navigation extremely simple and easy IFG zl 3 3 8 13 1 ken 50 PER ERD 5 Ehi da Gh Qc Go RES d 1 1300 Lal ARD Insert Prati PRO 10 Pr 2 06 11 162148 Freee Pro Back Bare Housing 1 Pair gema 13 Ji Fresfler Pro Locking Chuner 1 Pair i 200 162904 ROX PRO Date Plate Sel 2mmmtt Sei z AH ei 143 ADE PRO Dee Piste Set ent St 614 BD PRO 65 Ba Pintu Sut Domin 1 ade 1602011 Ena de PRLI BL Buss Piste Get dfn i My 8 o DN id 162 D LULA GA UL D M i 13 ECH b s innl fen Plato RACE PRO 1 Him 3 Pan 3 06 E A Fi ji TECHNICAL DATA In the product view mode technical data is available as additional information You may access this data by clicking on the spanner symbol You will find this A SCREW 5 5 X 8 6 MM 10 PCS symbol in the spreadsheet between the picture preview Dm S symbol and the symbol which opens the spare part viewer the toothed wheel symbol You can access the technical data sheet of one specific binding model or open the technical data catalogue for all models per line and season Te
33. the boot is satisfving the international standards and has no functional damage Take the binding parts out of the box and follow the steps on the instruction leaflet Determine the boot sole length with the rental caliper Art No 162617 Once the bindings are mounted onto a ski it is verv easv to adjust it to desiderate boot sole length Pict 9 First open the safetv lever 1 of the fusion central mechanism Keeping the safetv lever open now open pull up the second locking lever 2 and release them both Both levers must stay in open position so that bindings are released DO NOT USE TOOLS like a screwdriver to perform this operation Lock the central locking system by pushing down the lock lever 2 back to close position Finally check the forward pressure by placing a boot into the binding If you have followed all steps correctly the indicator should rest in the marked area If you have too much or not enough forward pressure check the settings and if necessary adjust slightly Then close the levers and check the forward pressure again Now it should be okay 4 ADJUSTMENT OF THE RELEASE VALUES The release values at toe and heel should be determined by height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws We recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requiremen
34. the clamping handles 1 and then place the template on the ski Align the boot midsole indicator 3 for the appropriate boot sole length with the midsole mounting mark on the ski Release the handles and ensure that the template is evenly seated against the ski s top surface Paper Template Art No 163010 Drill Template Art No 162976 The front holes are identical for both versions gold bushings You just have to select the right bushings for the rear holes ADRENALIN Short silver 270 330 mm ADRENALIN Long black 300 360 mm 2 2 PAPER TEMPLATE Align the boot midsole indicator for the appropriate boot sole length with the midsole mounting mark on the ski Fix it with a sticky tape and ensure that the template is centered and evenly seated against the ski s top surface After that you can mark the correct indicators with a punch Pict 03 AA drenalin The front holes are identical for both versions You just have to select the right indicator for the rear holes ADRENALIN Short 270 330 mm EE d 300 360 mm 3 DRILLING THE HOLES If not otherwise specified bv the ski manufacturer use the 4 1 x 9mm drill bit for the holes for the toe and the heel track and a 0 4 1 x 7mm drill bit for the holes for the locking mechanism If required by the ski manufacturer tap the holes LOTA TO TE CARA t Core pa O O A y N i 7 KR m After drilling place a drop of glue into
35. the settings on the binding match those on the record form and that the skier will inspect the system including the binding s AFD before each use e Signatures by both the customer and ELAN Certified Mechanic are required by for the ELAN Retailer Indemnity Program NOTE e Any changes in documentation requirements must be authorized in writing by Alpina Sports Corp USA ELAN Sports Inc Canada POST ACCIDENT INSPECTION REPORT see page 90 In addition to the above information on the system s performance fill out a Post Accident Report when you become aware that an injury has occurred Keep this document for 5 years or the duration of the statute of limitations for minors whichever is longer IN THE EVENT OF AN INJURY CLAIM e Notification to Alpina Sports Corp USA ELAN Sports Inc Canada by retailer of any bodilv injury claim must be made in writing on or before the tenth calendar day from the date on which the retailer first received notice of any such claim In the event of a lawsuit the retailer must notify his her own attorney and must cooperate with Alpina Sports Corp USA ELAN Sports Inc Canada and respond to requests as required e Inarenial situation from the time that any injury claim is made to the retailer the retailer must maintain possession of any equipment that may have been involved in the accident Equipment may be returned to service upon passing a post accident investigation e Inthe ev
36. the work has been completed according to the manufacturer s specifications e With testing complete the ELAN Certified Technician must complete and sign the workshop ticket Be sure the Final Indicator Settings are correctly shown there The workshop ticket should simply reflect that the system has passed all tests or that all manufacturer s procedures have been completed PROCEDURES FOR RETAIL CUSTOMER PICK UP All that s involved is properly informing the skier about the realities of skiing and ski equipment e Explain the function and operation of the binding including a review of the manufacturer s pamphlet e Explain the settings that show in the release setting windows and how they were derived by referring to the manufacturer s release adjustment charts e Explain how much proper maintenance of the entire system boots bindings and skis can improve their enjoyment and margins for safety Also make it clear that skiing like any sport has its risks and equipment can not eliminate them e Have the customer sign the form again indicating that they have been instructed on the use of the equipment and that they verified that the visual release indicators on the bindings correspond to the manufacturer s recommended settings shown on the work order ticket ARCHIVING RECORDS e Collect a copy of the technical manual for each and every binding boot and ski on the market Be especially diligent with those you
37. to take this product over the top Extra width and the superior kinematics of high performance bindings make it absolutely stable and reliable for perfect force transmission and unmatched performance The heel can easily be adjusted to different boot sole lengths without anv additional tools It covers a wide range of seven ski boot sizes The ADRENALIN freeride binding is available in two lengths SHORT S for ski boot sole length of 270 330 mm LONG L for ski boot sole length of 300 360 mm FREEFLEX The platform of ADRENALIN binding provides the approved Freeflex function which allows the ski to flex as it is designed to do so it can retain its natural dynamics Freeflex is enabled by the free gliding plate that runs within the titanal heel track and is supported by the center of rotation of the binding toe FREERIDE FR PRO TOE The ADRENALIN comes with the Freeride FR Pro Toe with its ergonomic pivot position for optimal tilt up movement up to 90 degrees This system provides efforiless walking over short distances The FR Pro Toe is adjustable by changing the position of the Anti Friction Slider AFS Metal to cover alpine and touring boot norms The AFS metal FR PRO Slider is available as a spare part Art No 162984 This 68 mm wide slider plus a stainless steel gliding element provides constant release values and result in a broader contact area to the ski boot sole The benefits more stabilit
38. weight range of the product Combine this Knowledge with our weight and ability recommendations for the skier when selecting a binding Do not sell a product with the idea that the customer will grow into it If a product is not suitable for their current requirements make another choice Avoid the temptation to do the customer a favor by rewriting the rules More often than not all you will do is cause problems and incur liability At the time of delivery to the customer the bindings must be accompanied by all the informational materials supplied by the manufacturer I e pamphlets forms etc The product must be fully demonstrated to either the intended user or their parent or legal guardian if the child is a minor This includes instructions on inspecting the low friction surfaces cleaning the boot sole entry of the binding re entry after releasing on the hill and exiting the system You must also explain what care and maintenance the skier or their parent or legal guardian is responsible for as well as when to return the equipment to your shop for a thorough function check Routine maintenance is the most cost effective thing a skier can do to protect their well being BOOT SELECTION Make sure the customer s boot choice is consistent with their level of skiing and that the boots meet all current DIN or ISO standards SKI SELECTION Take care to ensure that the skier s intended use of the chosen equipment is consistent
39. wider 88 97 115 130 150mm Some models are delivered without brakes This gives riders the opportunity to customize the setup to their needs Brakes are available in different widths 85 mm 95 mm 110 mm 130 mm and 150 mm Find Art No of all brakes on page 33 at ELAN brake line overview DEMO 8 RENTAL SUITABLE ATTACK 13 DEMO e The ELAN Attack 13 DEMO model a modified version of the ELAN Freeski binding is the first demo and rental suitable freeski binding that is anchored on a metal toe track This unique feature ensures a lower stand height a more compact design and increased stability compared with other bindings In combination with the proven ELAN Rental Heel track the Attack 13 DEMO offers the opportunity to fulfill every customer s desires whether for retail demo or rental purposes This easy to adapt ELAN Attack Freeski binding model was designed for a wide range of sole lengths and therefore can be adjusted to all available alpine boot sole lengths from 259 to 386 mm tool free in a matter of a few seconds by moving the toe and heel pieces 22 Safety Features TRP TOE SYSTEM SAFETY The 4 Roller Pincer System remains flexible at all times absorbing short impact peaks on ligaments and automatically re centering the boot Perfect 180 release action allows up to 30 higher retention force without compromising on safety CONVENIENCE Self cleaning design and maintenance free PERFORMANCE Positive
40. 0 Wide EL 10 0 EL 10 0 Wide EL 7 5 ELC 7 0 EL 4 5 ESP 13 0 ESP 10 0 ESP 7 5 ESP 4 5 ESR 10 0 Season 12 13 ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 ER 11 0 Wide 97 ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION Wide 88 ELX 11 0 FUSION ELW 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 10 0 FUSION EL 10 0 QT EL 10 0 QT Wide 90 ELW 9 0 QT EL 7 5 AC QT EL 7 5 AC QT Wide 90 EL 4 5 AC QT EL 4 5 AC QT Wide 84 EFS 18 0 w o brake EFS 15 0 w o brake ELX 14 0 w o brake ELW 11 0 wo brake EL 10 0 EL 10 0 Wide 90 ADRENALIN 16 w o Short ADRENALIN 16 w o Long SET Junior Kid EL 7 5 AC EL 4 5 AC ESP 13 0 w o brake ESP 10 0 ESP 7 5 ESP 4 5 AC ESR 10 0 Season 13 14 ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION Wide 88 ELX 11 0 FUSION ELW 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 10 0 FUSION EL 10 0 QT EL 10 0 QT Wide 90 ELW 9 0 QT EL 7 5 AC QT EL 7 5 AC QT Wide 90 EL 4 5 AC QT EL 4 5 AC QT Wide 84 EFS 18 0 w o brake EFS 12 0 w o brake EFS 10 0 Wide 90 EL 10 0 ADRENALIN 16 w o Short ADRENALIN 16 w o Long ADRENALIN 13 w o Short ADRENALIN 13 w o Long ATTACK 16 w o brake ATTACK 13 w o brake AMBITION 12 w o brake EL 7 5 AC EL 4 5 AC ESP 13 0 w o brake ESP 10 0 ESP 7 5 AC ESP 4 5 AC ESR 10 0 Season 14 15 ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 FUSION ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION Wide88 ELX 11 0 F
41. 0806 162800 162574 162575 162576 e Screwdriver flat per piece e Screwdriver incl Pozidrive 3 Bit 160805 Handy Ratchet incl bits 162575 162576 Slotted Screw Bit for Handy Ratchet e Pozidrive 3 Bit for Handy Ratchet Pozidrive 3 Bit for Screwdriver 162800 and electric drivers hexagon 1 4 6 35 mm e Pozidrive 3 Bit for electric driver Black amp Decker Skill Thor Atlas Copco Virax Consolidated Bosch Ingersoll Rand hexagon 1 4 6 35 mm Pozidrive 3 Bit for electric driver Bosch Metabo AEG hexagon 1 4 5 5 mm Pozidrive 3 Bit for electric driver Fein AEG Torx bit 25 50 1 4 inch per piece per piece per piece per piece per piece 160805 160802 per piece per piece 160803 160804 163066 162127 162128 162129 per piece per piece 10 pieces Special set for repairs drill bit and plugs e Drill bit for repair set Special plastic plugs for repair set per set per piece 50 pieces Plastic plugs mixed 500 pieces 160857 Plastic plugs silver 500 pieces 162856 Service Grease Spray 500 ml per piece 162779 e Grease per piece 160052 per piece 160858 e Rubber band for brake 162562 Rental Boot Indicator Single Code mm per piece 162617 Slide replacement for Rental Boot Indicator per piece 162518 SINGLE CODE Rental Boot Stickers 5 sheets 162561 e Boot Height Adjustment Tester Boot Height Adjustment Tester Adjustment Tes
42. 17 85 RACE LITE PB LD 85 RACE LITE PB LD 85 19 A 21 21 255 375 297 372 297 372 ADULT 92 W FAT ADULT 92 W FAT ADULT 92 W FAT 2680 g 2230 g 2 2 2 4 4 2050 g 3 3 3 2 2 Powerrail LD 85 Powerrail LD 85 Powerrail LD 95 Powerrail LD 85 Powerrail LD 85 Powerrail SL 78 Powerrail SL 78 35 35 35 35 35 3 2 RACE LITE RACE LITE RACE LITE RACE LITE RACE LITE 119 119 119 119 119 119 119 265 384 265 384 265 384 265 384 265 384 265 384 265 384 ADULT ADULT ADULT ADULT ADULT ADULT ADULT 1930 g 1930 g 1930 g 1920 g 1920 g 1770 g 1770 g NO e Q 1 es Powerrail SL 78 Powerrail SL 78 Powerrail SL WB 90 SL Brake LR 78 SL Brake LR 90 LA 120 120 120 84 or 68 84 or 68 265 380 265 380 265 380 M L or ML M L or ML ADULT ADULT ADULT ADULT ADULT 1770 g 1770 g 1770 g 1490 g 1490 g m r 3 m eg U gt 0 ID T TI m m m m m a A a m Q EL LITE EL LITE 31 31 SL LR 78 SL LR WB 90 SX Kid LR 74 SX Kid LR WB 84 S M or XSS SM ML S M or XSS SM ML S M or XSS SM ML S M or XSS SM ML A C A C A C A C 28 SX Junior 28 SX Junior 28 SX Kid 28 SX Kid 84 or 68 84 or 68 84 or 68 84 or 68 1380 g 1380 g 1270 g 1270 g H H de L E SL BRAKE WB 90 SL BRAKE 78 2 8 24 2 8 24 ADULT 92 W FAT ADULT 92 W FAT 1620 g 3 3 1620 g he 1 rm A T A
43. 966000 62966000 SX KID BRAKE LR A KID BRAKE LR 74 o er pana WW KID BRAKE LR 84 reg EL 10 0 EL 7 5 AC EL 4 5 AC ES AAA ATTACK OOOO 11 Not in collection 15 16 163058 DF163058000 SL Brake 78 E Brake 78 E J 162776 DF162776000 SL Brake 90 E J 163067 DF163067000 SL Brake 100 E 163068 DF163068000 SL Brake 115 E J 162965 SP162965000 SX KID BRAKE 74 K 162964 E EE KID BRAKE 84 K J J DF163027000 63027000 SL Brake FS 781 Brake FS 78 L DF163028000 SL Brake FS 90 L DF163029000 SL Brake FS 100 L DF163030000 SL Brake FS 115 L elam s Workshop Tools amp Aids To make your work easier ELAN provides a variety of workshop tools and aids Find the whole product range below Furthermore ELAN offers different templates for all available ski bindings Find the overview of the drill template selection 2015 16 on nexi pages Referring to this overview you are able to determine easily which template should be used with which binding For earlier lines refer to the corresponding Technical Manuals or use the Online Spare Parts OMS to search for specific information O e ro Drill Template Adapter Set adapter for Templates per piece 162569 e Drill Y 4 1 x 7 0 mm long e Drill 4 1 x 9 0 mm long e Drill 3 5 x 7 0 mm long e Drill 3 5 x 9 0 mm long Drill set complete 162772 162773 162770 162771 162774 per piece per piece per piece per piece per set 16
44. BILITY Presently the drill template ADRENALIN can be used for ADRENALIN 13 Long ADRENALIN 13 Short All ADRENALIN bindings come with 8mm penetration screws except the screws for the locking mechanism which have only 6 mm penetration and can be used with skis of groups G1 8 G2 Drill template ADRENALIN can be used for ski widths from 75 to 125mm For other skis use the template adapter set Art No 162569 With this adapter set skis from 61 to 149mm can be mounted NOTE ELAN offers different types of brakes Refer to the brake overview on page 33 for brake and binding compatibility The description of the brakes always includes a number and a color letter code This number stands for the maximum ski width in the brake area and not in the ski center The color letter code defines the brake segment 2 POSITIONING OF THE TEMPLATE There are two ways to mount ADRENALIN bindings Either with the solid jig Art No 162976 or with the paper template which is included in the packaging of each binding We will show both procedures First of all make sure that the boot is satisfying the inter national standards and has no functional damage Determine the boot sole length with the rental caliper Art No 162617 w NOTE Keep in mind that some ski manufacturers do not use the center of boot sole location method Always follow the ski manufacturer s instructions 2 1 DRILL TEMPLATE Open the clamping jaws 2 by rotating
45. BY ELAN The 2015 16 ELAN Release Retention Adjustment Table is the only adjustment chart recommended for use by ELAN dealers during the 2015 16 season Some skiers may request settings different from those in the ELAN Release Retention Adjustment Table Most of these concerns can be addressed by following the procedures for reclassifying skier type and for troubleshooting which follow the instructions for using the ELAN Release Retention Adjustment Table ELAN and the ISO ASTM standards organizations do not recommend the use of release retention settings outside of these tolerances but skiers occasionally may request such settings ELAN recognizes a skier s right to choose other settings but if the skier requests settings outside of those derived from the normal procedures for re classifving skier type and for troubleshooting the shop may either 1 Adjust the svstem to the setting derived from ELAN Release Retention Adjustment Table and instruct the skier on how to change the setting if this done make a note to this effect on the workshop or rental form or 2 Adjust the system to the skier s individual request but only if the technician notes on the workshop or rental form the reason the higher or lower setting was requested Do not in anv case adjust the svstem to a release retention value higher than the maximum acceptable setting at the bottom of the ELAN Release Retention Adjustment Table The customer must verifv the reque
46. C RDX as it comes with 1 8mm penetration screws e e For EP 11 5 DUO Junior with 6 mm penetration screws use the 4 1 x 7 0mm drill bit if not otherwise recommended 54 Then you can place the front and the rear part over the screws and push it in the appropriate position Make sure that the washer stays in its position To fix the plate just tighten the screws l Y f l l l i k j PAN A gt r NW eg A f ef N p 4 2 MOUNTING BINDING ON EP 14 WC RDX Before mounting the binding on RACEPLATES please check the boot sole range scale on the plate NOTE Use only the pre drilled holes for installation do not drill holes into the plate to mount bindings of other manufacturers Change the screws of the standard rear heel according to the mounted binding The screws come in the box with race bindings all ER models O standard change Other than those the mounting is similar to the method described in the chapter Drill Template 92 W amp FAT 5 MOUNTING RACEPLATE JUNIOR 5 1 MOUNTING PLATE EP 11 5 DUO The compatible binding plate combinations can be found in the Technical Manual chapter Binding Plate Coordination Line Place the front part of the plate over the holes and fasten the screws Then place the back part over the holes and fasten the screws 5 2 MOUNTING BINDINGS ON EP 11 5 DUO For mounting junior bindings on ELAN PLATES you ha
47. ELX 11 0 FUSION ELW 11 0 FUSION Lady EL 11 0 FUSION EL 10 0 FUSION ELW 10 0 FUSION Lady QuickTrick QT EL 10 0 QT EL 10 0 QT WB90 ELW 9 0 QT Lady QuickTrick QT JUNIOR EL 7 5 AC QT EL 7 5 AC QT WB90 EL 4 5 AC QT EL 4 5 AC QT WB84 EFS 10 0 WB90 EL 10 0 AAA Series ADRENALIN 13 w o Short ADRENALIN 13 w o Long ATTACK 18 X w o brake ATTACK 16 w o brake ATTACK 13 w o brake ATTACK 13 DEMO w o brake ATTACK 11 w o brake AMBITION 12 w o brake AMBITION 10 w o brake SET Junior Kid EL 7 5 AC EL 4 5 AC RENTAL ESP 10 0 w o brake ESP 10 0 ESP 7 5 AC ESP 4 5 AC ESR 10 0 RETAILER AGREEMENTS AND INDEMNIFICATION AGREEMENTS Both Agreements must be completed annually This year s Retailer and Indemnification Agreements should already be completed if not please contact customer service or your sales rep Agreements and Certification Exams should be received at Alpina Sports Corp USA ELAN Sports Inc Canada no later than December 31 2015 An administration fee of 10 00 U S per year for each certified mechanic max 60 U S per location will be charged by ELAN If a retailer loses his only ELAN certified mechanic he must notify Alpina Sports Corp USA ELAN Sports Inc Canada in writing within 48 hours SUMMARY OF REQUIREMENTS These basic requirements help assure that the end product which is delivered to the customer is appropriate e Signed current copies of the ELAN Authorized Retaile
48. G1 amp G2 replace the pre mounted screws by 8 mm penetration depth screws see chapter Spare Parts Handling on page 31 Only with these screws we can guarantee the right pullout strength elam s Binding Plate Coordination Line 2015 16 EP 14 0 WC EP 9 0 EP 9 0 EP 11 5 DUO EP 11 X Raceplate RDX Height 14mm 9mm 9mm 11 5mm 12 10mm Mounting range 258 372mm 258 3 2mm 258 3 2mm 238 342mm 260 342mm Mounting range EL 261 363mm 261 363mm 261 363mm 241 353mm 263 353mm STAND HEIGHT mm ER 20 0 X FreeFlex EVO ER 16 0 X FreeFlex EVO Attack 18 X Attack 16 Attack 13 Attack 11 ER 11 0 FreeFlex Pro ER 11 0 EFS 10 0 EL 10 0 EL 7 5 ESP 10 0 ESP 7 5 AC EL 4 5 AC ESP 4 5 Note IX non compatible System Bindings Fusion QT Adrenalin Ambition 66 ELAN Brake Matrix 2015 16 4 0 L G1 ZIXVHI TIVHHIMOd 9 SZ NOLLIENY IMV HS 4 OLL GIZAMVHA TIVHHIMOd 1 SLL SA SVE TS 9 SOL NOLLIENY 3AVyH49 4 S6 41 caNV HS TIVHHIMOd 1 00L S4 INVHS IS 9 lt 6 NOLLISWV 3NVHS a os G1 ZIMVHA HIMOd 1 06 S4 IXNVHS TS 9 68 NOILISINV 3 Vyg a OCL GI ZMVHA HIMOd 4 82 Sd SVU IS a OLL G1 cINVHI HIMOd 1 3 GLL INVHI IS r a s6 71 caNVHS HIMOd ma 3 00L IMVHS9 IS A g 0 L Od H4 ZMVHA HIMOd P 3 06 IMVHS IS f g OLL OHd H4 ZIMVHA HIMOd 3 82 3MVHA 1S g 66 OHd H4 ZIMVHA HIMOd 4 98 01 Z MVHY TIVHHIMOd H 06 HT IXNVHS IS V OSL Odd JOVH ZIMVHA HIMOd a se d1ZIMVHA HIMOd
49. INDINGS ESP 10 0 ESP 7 5 AC ESP 4 5 AC DRILL TEMPLATE SR 2003 W 162762 BINDINGS ESR 10 0 Drill Template 92 W 92 FAT Drill template 92 W Art No 162760 for ski widths from 59 to 108mm 1 COMPATIBILITY Presently drill templates 92 W and 92 FAT can be used for ER 20 0 X FF EVO ER X 16 0 FF EVO ER 17 0 FreeFlex Pro Attack 18 X ER 11 0 FreeFlex Pro Attack 11 EFS 10 0 EL 10 0 EL 7 5 AC All ELAN s adult bindings come with screws with a penetration depth of 8 mm for skis group G1 amp G2 The junior EL 7 5 AC bindings are delivered with screws with a penetration depth of 6 mm For mounting junior bindings on ELAN Plates or on skis group G1 8 G2 replace them by longer screws Drill template 92 W can be used for ski widths from 59 mm to 108 mm For other skis use the template adapter set Art nr 162 569 With this adapter set skis from 45 to 132 mm can be mounted Drill template 92 W can be used for ski widths from 59 mm to 108 mm whereas the drill template 92 FAT fits ski widths from 104 mm to 154 mm For other skis use the template adapter set Art no 162569 With this adapter set you can mount skis from 45 mm to 132 mm with the standard drill template 92 W as well as skis from 90 mm to 178 mm with Drill Template 92 FAT NOTE ELAN offers different types of brakes Refer to the brake overview on page 33 for brake and binding compatibility The description of the brakes always i
50. In combination with two rollers this binding provides superior safety features with the rapid and exact boot re centering that skiers expect from ELAN As a result of its harmonious design the ELAN AMBITION has a wider contact area which improves stability and provides a secure foundation for every skiing situation Furthermore its pivot is efficiently positioned right below the ski boot tip to ensure perfect force transmission and a tilt up to 90 degrees CRAMPONS Additional crampons are available as spare parts in widths of 90 mm 105 mm and 120 mm and provide safe climbing and a secure Stand in any situation 90 mm Art No 163006 1 Pair 105 mm Art No 163007 1 Pair 120 mm Art No 163008 1 Pair renalin THE PERFECT ALL ROUNDER With the ADRENALIN Freeride binding ffom ELAN no terrain is out of reach This binding provides a level of skiing performance never before seen in an alpine binding It combines performance driven freeride features with the ultimate ergonomic walking mechanism for maximum freedom on and off piste Overcome boundaries smoothly for a perfect ride ALPINE TOURING HEEL AND CLIMBING AID BRAKES amp INDIVIDUALITY With the new ADRENALIN Freeride binding from ELAN no terrain is The ADRENALIN comes without brakes out of reach This binding provides a level of skiing performance never This gives each freerider the chance to before seen in an alpine binding It combines performance drive
51. No 162617 310 mm Open the toe lever and slide the toe on the rail from the front Lock at the appropriate boot sole length and close the lever m Now hook the brake into the heel housing Then open the heel lever slide the heel on the rail from the back and lock it at the appropriate boot sole marking Don t forget to check that the lever is closed again Ne Finally check the forward pressure by placing a boot into the binding If you have followed all steps correctly the indicator should rest in the marked area 58 If vou have too much or not enough forward pressure check the settings and if necessary adjust slighily at the heel and the toe Then close the levers and check the forward pressure again Now it should be okav ee 3 ADAPTATION Once the binding is mounted onto a ski it is very easy to adjust it to another boot sole length Just open the levers and slide toe and heel to the desired length mark Finally close the levers and check forward pressure as described before 4 ADJUSTMENT OF THE RELEASE VALUES The release values at toe and heel should be determined by height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws We recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US NOTE Release Retention settings above a release moment of 100Nm
52. P 2003 W Art No 162763 for ski widths from 59 to 108 mm 1 COMPATIBILITY Drill templates SP 2003 W and SP 2003 FAT are used for ESP models ESP 7 5 AC ESP 4 5 AC All ELAN adult bindings come with 8mm penetration screws and can be used with skis group G1 amp G2 The junior binding ESP 7 5 is delivered with 6mm penetration screws for skis groups G3 amp G4 If it is mounted on skis groups G1 G2 or on ELAN Plates replace them with longer screws see chapter Spare Parts Handling ESP 4 5 comes with 6mm penetration screws and is only for skis group G3 amp G4 Drill Template SP 2003 W can be used for ski widths from 59mm to 108mm the drill template SP 2003 FAT for ski widths from 104mm to 154mm For other skis use the template adapter set Art No 162569 With this adapter set you can mount skis from 45mm to 132mm with the standard SP 2003 W drill template as well as skis from 90mm to 178mm with drill template SP 2003 FAT NOTE The standard brake for all ESP bindings except the ESP 4 5 is the POWER BRAKE LD 78 which can be used for skis up to 78 mm The standard brake for the ESP 4 5 AC is the SX KID BRAKE 74 which can be used for skis up to 74mm for wider skis use the SX KID BRAKE wide 84 which is for skis from 74 to 84mm There are different types of brakes Refer to the brake overview on page 33 for brake and binding compatibility The description of the brakes always includes a number and a color letter c
53. PLATE Align the boot midsole indicator 3 with the midsole mounting mark on the ski Be sure the template is evenly seated against the ski s top surface Release clamping handles to attach the template to the ski Check the boot midsole mark with template mark If they are not the same use the boot midsole mark to align the template with the ski mounting mark NOTE Some ski manufacturers do not use the center of boot sole location method Always follow the ski manufacturer s instructions 4 DRILLING THE HOLES ELAN skis refer to the Drill Bit chart on the page 8 If not otherwise specified by the ski manufacturer use an O4 1x 7 0mm drill bit which is the right bit for skis group G38GA Drill the holes using appropriate drill If required by the ski manufacturer tap the hole Place a drop of glue into the holes It lubricates the screws and seals the ski Pict 01 52 Drill template 94 W Art No 162761 Teen Arg 5 MOUNTING Place toe unit over the holes and fasten the screws in an X pattern Then do the same for the heel 6 FORWARD PRESSURE Place the boot in the binding and close it The indicating pointer should rest within the scribed area Pict 03 if not you have to adjust the forward pressure DON T OPEN THE LENGTH ADJUSTMENT LOCK AS LONG AS A SKI BOOT IS FIXED IN THE BINDING Place the ski boot in the open binding and rest the boot heel on the brake treadle Lift the length adjustment lock
54. USION ELW 11 0 FUSION Lady EL 11 0 FUSION EL 10 0 FUSION ELW 10 0 FUSION Lady EL 10 0 QT EL 10 0 QT Wide90 ELW 9 0 QT Lady EL 7 5 AC QT EL 7 5 AC QT Wide90 EL 4 5 AC QT EL 4 5 AC QT Wide84 EFS 18 0 w o brake EFS 12 0 w o brake EFS 10 0 Wide90 EL 10 0 ADRENALIN 13 w o Short ADRENALIN 13 w o Long ATTACK 16 w o brake ATTACK 13 w o brake ATTACK 13 DEMO w o brake AMBITION 12 w o brake AMBITION 10 w o brake EL 7 5 AC EL 4 5 AC ESP 10 0 w o brake ESP 10 0 ESP 7 5 AC ESP 4 5 AC ESR 10 0 Racing X Word Cup models ER 20 0 FREE FLEX ER 16 0 FREE FLEX ER 20 0 FREE FLEX PRO ER 16 0 FREE FLEX PRO ER 20 0 FREE FLEX EVO ER 16 0 FREE FLEX EVO 92 EQUIPMENT RENTAL FORM Date out Date in PLEASE PRINT CLEARLY E First Name Address City Prov State Country Postal Code Zip Phone Number e mail Local Phone Number JATU IA A A O eut Your Weight Your Height Skier Type Age No of Days Wanted a hs nm Circle One D ES Loy FOR OFFICE USE ONLY da Ti VALUE 251 271 291 Skier Final Indicator Single Gode Setting HEIGHT EE WEIGHT FTIN 2 L R ka L R 14 17 kilo 39 47 Ibs Rent Own ID or Description 18 21 kil Skis O V ka E de o ca Go Po Slzlrzls lzlslzlcis irzl l jale sofjos SVR Sis Boots Poles Suit S board S board Boots Cross Countrv Other Other JE de a c IJU LI JU OOO ILI
55. YEARS DE INNOVATION WWW ELANSPORTS COM THE MOST INNOVATIVE BRAND IN SPORTS EQUIPMENT Given the number of awards the company has received in the last 8 years Elan is undoubtedly on the right track While the company is certainly flattered by all the attention it gets from award committees it knows that its true judges are the loyal users of its products Elan is committed to constantly developing innovative functional and elegantly designed products for every product line The title of Most Innovative Brand the highest award presented annually by the German organization Plus X Award has been bestowed on Elan for three years now in 2012 2013 and 2015 The award winning brands are selected on the basis of their outstanding achievements in the areas of quality design user experience functionality ergonomics and environmental consciousness Receiving this award certainly constitutes a validation of Elan s vision of becoming number one in sporting goods innovation Yet as mentioned it is the smiles on skiers faces that bring the company the greatest satisfaction With 47 awards and counting Elan is a real award collector PLUS X AWAR PLUS X AWARD OST IOVATIVE 3RAND MOST ATIVE PRODUCT INNOVATIVE AND 2012 kenen HE YEAR Design High Quality mese 13 i 2014 2013 Functionality Design Most innovative brand in 2012 2013 and 2015 COLLECTION 1314 Amphibio 14 Fusion COLLECTION 1415 Juni
56. a customer the shop may do so after the approval of the ski warranty department of your ELAN distributor e Be sure to check suitability and mounting hole pattern before making a change of model e When possible the replacement should be of the same model as the returned product e lithe same model is not available the shop should contact the authorized ELAN distributor warranty department for authorization before a more expensive model is selected for replacement e fa replacement is made from retailer stock the complete binding set should be returned to the authorized ELAN distributor as soon as possible e The packing list must clearly state which model was used for replacement e The Instructions for Use booklet warranty and proof of purchase must accompany all products returned for consideration e Nocredits will be issued e The authorized ELAN distributor reserves the right to deny replacement to the retailer if the alleged problem is not verified or if products are returned without the Instructions for Use booklet and proof of purchase e Replacement bindings are covered by the warranty stated above 86 e Any bindings returned to the authorized ELAN distributor due to inappropriate release values i e values which fall outside the In Use tolerance range on the current ELAN Adjustment Chart must be accompanied by a completed System Performance Report The report form is printed in this manual
57. agreed time and date If l fail to do so agree to pay for its repair cleaning or replacement at the full retail rate as determined by the shop as well as for the rental value of any additional days For release bindings only have confirmed that the binding release retention setting numbers on the bindings correspond to the Final Indicator Setting stated on this form understand that correct weight height age and skier type are essential to proper adjustment of the release retention settings and certify that all user information on this form is correct AMOUNT PAID X SIGNATURE OF USER OR AGENT DATE X PARENT S SIGNATURE IF USER IS A MINOR DATE Elan is fully committed to a comprehensive environmental management system to minimize its impact on nature as verified by the environmental standard ISO 14001 Elan d o o Begunje 1 4275 Begunje na Gorenjskem Slovenia Elan reserves the right to introduce modifications and changes without prior notice
58. al SymPro ESP SvmRent ESR 15 16 Performance for a rental binding is not only what happens on the hill A key measure of a product s quality is the ease with which a system can be adjusted and maintained throughout the course of many seasons THE ELAN S SHOP FRIENDLY RENTAL DESIGN FEATURES e Easy mounting This means fewer mistakes and reduced set up time e Easy pre season testing low drop out rate The automatic sole lug design and the precise centering of the toe pincer system mean fewer correction factors will be needed and less time spent testing e The SINGLE CODE system gives you a super fast option for binding to boot adjustment set the heel length using the special sole length scale Forward pressure will be right on first time every time e All models have automatic lug height adjustment which accommodates standard differences in boot sole height e Easy hand levered ONE TOUCH set up One tool adjustment easy to turn adjustment screw easv in boot feature e Almost maintenance free easy to change the AFD clean and lubricate the heel track ELAN made the commitment to offer a comprehensive produci and service program THE ELAN RENTAL BINDINGS No single rental binding can ever fulfill all the needs of all types of shops We therefore offer the following line up of rental demo models SYMPRO THE BINDINGS THAT HELP YOUR HIGH PERFORMANCE SKI SET UP ESP 10 0 e Hand lever adjusted heel 60 m
59. amping jaws of the mounting template 3 Position the template properly on the ski so that the boot center marking is aligned with the mounting point described on the ski 4 Letgo of the clamping lever The template clamps automatically Drill all the holes Remove the mounting template and clean the ski Measure the holes with a slide gauge The distance of the screw holes to the edge of the ski must be equal for each pair of related holes The deviation must not be more than 1mm Repeat the test if greater deviations occur 10 The mounting template must be discarded if greater deviations occur again 13 REPAIR OF DAMAGED MOUNTING HOLES OR BROKEN SCREWS For repairing damaged holes we suggest our special Repair Set Art No 162 127 It consists of a hollow drill bit and plastic inserts Pict 10 T ONDA Dess You can extract broken screws too Remove the binding from the ski Drill with the hollow drill through the bushing of the appropriate drill template and drive in the plastic insert Mount the binding again Pict 11 elam s Troubleshooting Including Rental Problem PossibleReason Solution Ski obstructs brake Replace the standard brake with a O e sarge Wa Reference binding worn Recheck reference binding with a boot Boot fails pre season test that has passed Boot does not meet ISO 5355 Replace boot Improper use of testing device Check calibration and opera
60. any warranties or assertions about the customer s safety on the hill Speaking simply no binding is absolutely safe Well designed shop record forms address the disclosure and agreement subject very directly and professionally Use them to your advantage by making sure customers read and understand the form before signing it The following points must be explained to all customers rental or retail before they leave the shop with their equipment consumer awareness checklist e Go through your workshop ticket and fully explain each task that has been performed by the shop e Explain how to use bindings and equipment Let customers put on their boots and step in and out of the binding if needed e Remind skiers to clean their boots and bindings each time before stepping in Tell them that they should always walk through clean snow before entering the bindings e Deliver the Instructions for Use booklet to retail customers It is an important document and is essential for warranty service e Advise the customers to return to your shop periodically for maintenance and a system inspection The service interval is once each 15 20 days of skiing or annually whichever comes first e Recommend care in transport heels closed bindings covered e Recommend care in storage dry moderate temperature heels closed and boots not in bindings e Explain that bindings and boots must be kept clean for optimal function e
61. at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skier s own risk 5 FUNCTION CHECK Check the function of the heel Make sure that the boot does not catch on the heel during entry and exit Check the brake function by pressing down the brake pedal 1 by hand The brake arms 2 must open to the braking position when the brake pedal is released see pict 07 Check the elasticity and retention of the toe by pushing the boot inward and outward The binding must re center the boot easily and quickly from a 15mm lateral displacement 6 FINAL CHECK Is the proper mounting point selected Functional brake test passed Is the forward pressure properly adjusted Are the release values of toe and the heel properly determined and set e Isthe Instruction for use booklet ready to be handed over to the customer Mounting instruction GT Junior 8 Lady 1 COMPATIBILITV Now hook the brake into the heel housing ELAN offers two types of plates the QuickTrick TMD base and QuickTrick SnapIN base 199 283 qr 239 323 263 347 195 263 225 293 255 323 All ELAN s QuickTrick plates are pre mounted on skis Presently the QuickTrick plates can be used for next bindings Then you can open the lever and slide the heel on the rail ELW 9 0 QT EL 7 5 AC QT from the back EL 7 5 AC QT WB 90 EL 4 5 AC QT EL 4 5 AC QT WB 84 2 MOUNTING BINDINGS Make sure that th
62. believe that you require lower release retention settings but are unsure if the decrease should be applied to twist or forward lean settings request that the decrease be applied to twist settings before experimenting with lower forward lean settings Lower settings correspond to an increase in the risk of inadvertent binding release in order to gain increased releasability in a fall Higher settings correspond to a decrease in releasability in a fall in order to gain a decreased risk of inadvertent binding release 5 Although the shop technician may help you to record your choice on the appropriate form the final decision on your release retention settings is yours elam 7 SYMPRO SYMRENT on the Shop Floor PREPARING AND CHECKING RENTAL SYSTEMS Customers usually don t treat rental equipment as gently and carefully as they would handle their private property In order to keep your rental fleet as functional and appealing as possible a systematic maintenance program is a must The best results are obtained with an ongoing program which constanily checks boots bindings and skis SINGLE CODING This enables a quick boot and binding coordination even during the rush hours of rental business ELAN offers self adhesive color stickers art no 162561 with the SINGLE CODE to be applied before season You simply check the boot s SINGLE CODE and adjust the binding accordingly In order to gain the efficiencies of ESP all you need t
63. binding accordingly with the adjustment screws at heel and toe unit ELAN recommends adjusting these settings with a manual screwdriver Do NOT use a screw shooter We also recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US NOTE Release Retention settings above a release moment of 100 Nm at the toe and 425 Nm at the heel are higher than the international standards recommend and are used solely at the skier s own risk 8 FUNCTION CHECK Check the function of the heel Make sure that the boot does not catch on the heel during entry and exit Check the brake function by pressing down the brake pedal 1 by hand The brake arms 2 must open to the braking position when the brake pedal is released Check the elasticity and retention of the toe by pushing the boot inward and outward The binding must re center the boot easily and quickly from a 15mm lateral displacement Pict 22 9 ADDITIONAL EQUIPMENT AND SPARE PARTS FOR AMBITION 9 1 AMBITION CRAMPONS ELAN is offering additional crampons for AMBITON Bindings Use the crampons in icy and hard snow conditions to provide safe climbing and a secure stance in any situation Be sure to use the right width 90mm Art No 163006 105mm Art No 163007 or 120mm Art No 163008 48 MOUNTING Open the climbing aid and swing open the binding Take the crampon and slide it to the fixing positi
64. chnical Data for all ELAN lines from season 2009 2010 up to the current line is available online ONLINE HELP i TECHNICALDATA A HELP Document is also available online Vou will find AA DATA HEEL itin the OMS in the top right corner a mie a ORDERING a ta 3170 Simple fill the standard order form Some parts as vun screws are not included in that form therefore additional blank copy of the form is available on WEB Just fill 6 digits numbers Art Nr and desiderate quantity ELAN Brake Line 2015 16 e POWER BRAKE for A B D and F e Standardization of brake group E and J e Identification and Naming svstem e wlo brake binding models 85 95 10 130 150rmm 1 Power Brake for A B D and F The new Power Brake with a better retraction up to 30 mm in comparison to former brakes has been introduced The new brake retracts completely to the heel housing Therefore the amount of brake models in PB segments A B IDI and F due to new width split 85 95 110 130 150 mm have been reduced from 26 to 19 models Power Brake feature a fully compatibility new brakes match with old bindings and old brakes match with new bindings 2 STANDARDIZATION OF BRAKE GROUP E AND J A standardization of the former Brake group E and J was made That means these 2 groups will be combined in the new group E J in the first step and after existing stock is delivered the E will be d
65. d tightly e s the forward pressure properly adjusted e Are the release values of the toe and the heel properly determined and set e s the instruction for use booklet ready to be handed over to the consumer elam 5 Drill Template 94 VV 1 COMPATIBILITY Drill template 94 W can be used for EL 4 5 AC Drill template 94 W can be used for ski widths from 59mm to 108mm For other skis use the template adapter set Art no 162569 The EL 4 5 AC binding comes with 6mm penetration depth screws and thus could be used for skis group G3 amp G4 The standard brake the SX KID BRAKE 74 Art nr 162 983 can be used for skis up to 74mm for wider skis use the SX KID BRAKE wide 84 Art nr 162 964 which is for skis from 74 to 84mm NOTE ELAN offers different types of brakes Refer to the brake overview on page 33 for brake and binding compatibility The description of the brakes always includes a number and a color letter code This number stands for the maximum ski width in the brake area and not in the ski center The color letter code defines the brake segment 2 ADJUSTING THE DRILL TEMPLATE Unlock the locking lever 1 by rotating it counterclockwise Place the template on the ski Place the ski boot in the template Push the template together until the violet stops are against the sole comes 2 Lock the lever 1 to prevent length change and take the boot out of the template 3 POSITIONING OF THE DRILL TEM
66. dix The binding list for retailers previous seasons Season 05 06 ER 17 0 FREE FLEX ER 11 0 FREE FLEX ER 11 0 Fusion PRO ELD 12 0 FUSION PRO ELD 11 0 FUSION PRO ELD 12 0 FUSION ELD 11 0 FUSION EL 10 0 FUSION RED EL 9 0 FUSION ELD 11 TMD EL 10 TMD ELW 9 TMD ELD 14 0 ELD 14 0 Wide EL 10 0 EL 7 0 EL 4 5 ESP 13 0 ESP 12 0 ESP 10 0 ESP 7 0 ESP 4 5 ESR 10 0 ESR 7 0 ESR 4 5 ELD 12 0 XP ELD 11 0 XP EL 10 0 XP EL 7 0 XP Season 06 07 ER 17 0 FREE FLEX ER 11 0 FREE FLEX ER 11 0 ELD 14 0 FUSION PRO ELD 12 0 FUSION PRO ELD 11 0 FUSION PRO ELD 12 0 FUSION ELD 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 9 0 FUSION ELD 11 0 TMD EL 10 0 TMD ELW 9 0 TMD Jr EL 7 0 TMD Jr EL 4 5 TMD Jr ELD 14 0 ELD 14 0 Wide EL 10 0 EL 7 0 EL 4 5 ESP 13 0 ESP 10 0 ESP 7 0 ESP 4 5 EL 11 0 XP Season 07 08 ER 17 0 FREE FLEX ER 11 0 FREE FLEX ER 11 0 ELD 12 0 FUSION PRO ELD 11 0 FUSION PRO ELD 14 0 FUSION Wide ELD 12 0 FUSION ELD 12 0 FUSION Wide ELD 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 11 0 FUSION ELW 11 0 FUSION Wide ELW 9 0 FUSION ELD 11 0 TMD EL 10 0 TMD ELW 9 0 TMD Jr EL 7 0 TMD Jr EL 4 5 TMD Jr ELD 14 0 ELD 14 0 Wide ELW 11 0 EL 10 EL 7 0 EL 4 5 ESP 13 0 ESP 10 0 ESP 7 5 ESP 4 5 Season 08 09 ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION Wide ELX 11 0 FUSION EL 11 0 FUSION EL 10 0 FUSION ELW 11 0 FUSION ELW 9 0
67. ds landing Power Brake retracts completely to the heel housing with 22 5 mm better retraction As well brake widths for categories A B D and F were standardized 22 5mm 85 95 110 130 150 mm 22 5mm Furthermore the new Power Brake is fully compatible with existing binding models to turn them into dream racing machines 16 ATTACK 18X For optimal backcountry performance powder skiing or park amp pipe action the new Attack 18X is equipped with Magnesium wings for more solidity and stability With the specific AAA construction the binding is 160g lighter than the previous Peak 18X binding What limits you to make even more turns Certainly not the binding Stand Height DIN Boots Weight Features ATTACK 11 ELAN ATTACK 18X 17 mm 8 18 Alpine Norm 2080 g 2380 g FR Pro Toe with Magnesium AFD Metal Race Pro Heel Dura Coated Also NEW in the Attack binding family is the Attack 11 with the innovative SX Freeski Heel constructed with the needs of young freeskiers and freestylers in mind Stand Height DIN Boots Weight Features ELAN ATTACK 11 21 mm 3 11 Alpine Norm 1360 g 1660 9 FR Pro Toe AFD Metal SX Heel Dura Coated Solid Colored bition THE TOURING BINDING The ELAN Ambition Alpine Touring binding is the perfect companion for all Alpine Touring Aficionados so that no terrain remains unattainable We included every attribute of our high
68. e Country Postal Code Zip 111 100th 1 Anytown MA USA 1100 001 Phone ZA Local Phone Number 0 0 0 isampleDanywherecom 1123 4567 Your Weigh Your Height Skier Type a No of Days Wanted zum Tia Circle One 1 ir IM 13 5 0 2 FOR OFFICE USE ONLY INITIAL INDICATOR Skier Final Indicator e tals SOLE LENGT es SAW D Een FT wi EES 0 T2 13 9 ae 455 455 Sai 39 47 Ibs RentiOwn ID or Description M cl Li Skis xi C SIX Waveflex FRS pel de 1 week of NTO On PI 0 ho e NA SRR Isi izizjaloimi pi slal ls aa ae WE M Di ZA MEE S 3 ojo s o 3 Se Ja bs LA be EI ech 63 gt gt Al aah w Fi 25 kilos Boots Xx KRYPTON PRO 31 35 kilos 79 91 lbs 1 3 E 42 48 kilos lt 1 48 108 125 lbs 4117 5 1 Li e AP Ge 66k E dee 5107 E 1 67 1 78 Ges E 79 94 kilos Other gt 210 lbs a Other Insurance E NM gt e fo gt DI ee np me gt Poles Suit S board S board Boots Cross Country no B Ojoo o jojos o sch ERROR E x el el zs a z S elei vr COMMENTS REFERRED BY x John Mastertech S UU TECHNICIAN S SIGNATURE TE have read understood and agreed to all terms and conditions on the reverse side of this form accept full financial responsibility for the equipment listed on this form and promise to return it clean and undamaged by the
69. e Please use only ELAN recommended lubrication Tyrolia grease 160052 Standard FAT Ambition amp Adrenalin Drill Template Drill Template Drill Template 59 108 mm 104 154 mm 75 125 mm Tyrolia service grease spray 162779 50 99 mm 95 145 mm 66 116 mm Both have the same content but the grease tube is for more precise lubrication and the spray is suited for spots which are hard to reach with the tube e Clean the surfaces with a dry rag or warm water and mild soap e Avoid any contact with aggressive solvents or degreasers e Don t use cleansers elam 7 High pressure cleaning is not recommended It might have the negative side effect of washing away the lubricating films 11 1 LUBRICATING THE TOE PIECE AERO TOES Lubricate the adjustment screw and the guides of the main spring in the housing with the Tyrolia service grease spray ALL SYMPRO ESP TOES In case of friction in the track system Mark the toe position open the ESP hand lever and slide the toe piece off Dry clean the track and the toe guide base gentiv using a plastic brush Then lubricate the locking mechanism at both sides of the toe guide base Lubricate also both sides of the track guide over the entire length di 11 2 LUBRICATING THE HEEL ALL RENTAL BINDINGS Mark heel position open the hand lever and slide the heel off backwards At the ESR 10 the guide lock has to be opened with a screwdriver Pict 05 to get th
70. e adjustment table e Approved mechanical testing device e Screw extractor e Tap extractor e Hole plugs plastic amp wood e Threaded plastic ski inserts e Chisel e Hammer CREATING AN INFORMED CONSUMER Customers whether rental or retail come to your shop with all levels of knowledge The range extends from true experts who really Know the sport and their equipment needs to never ever skiers who know they must rely totally on your expertise A key role played by a good shop and a requirement in the U S and Canada under the ELAN Retailer Indemnity Program is providing information guidance and instruction to all customers SPECIFICALLY THIS MEANS e Providing product and suitability information to help customers make an informed choice of which equipment models are right for them The amount and type of advice given will naturally be different for each customer e The shops responsibility is to be sure that each product sold or serviced is appropriate for the needs of its user e The shop must provide accurate information about the nature of the sport and what equipment can and cannot do Inform customers that there are risks inherent in the sport of skiing that no binding can protect against It is imperative that each customer be informed there are limitations to the protection their equipment can afford and that injuries can and do occur in the normal course of Skiing e Under no circumstances should you make
71. e binding off LUBRICATE 72 the edge of the release cam under the heel lug as shown in Pict 06 Both sides of the heel track inside over the entire length Bearings of the opened hand lever on both sides Pict 07 e The guiding channel of the release setting adjustment screw After finishing the heel lubrication slide on the heel and lock it in its original position 11 3 BINDING ESP 4 5 AC LUBRICATE e The contact areas between housing and the release cam on the front side and the backside as shown in Pict 08 and 09 e Both sides of the heel track inside over the entire length o TA The guiding channel of the release setting adjustment screw Pict 09 WT Zei VW dos After finishing the heel lubrication slide on the heel and lock it in its original position 11 4 NOT TO BE LUBRICATED The locking element and the corresponding holes in the heel track should be cleaned but not lubricated This should prevent dirt accumulation in this area which could interfere with the ease of handling 12 TEST YOUR DRILL TEMPLATE 14 SEALING OLD MOUNTING HOLES A worn or damaged drill template could create a lot of trouble For sealing old holes you can use wood plugs or plastic plugs Please check your templates periodically art no 160857 if not otherwise specified by the ski 1 Position the fully extended drill template on a discarded manufacturer ski 2 Turn the clamping lever to open the cl
72. e binding with less forward pressure The synchronal adjustment of the wings provides precise adjustment to ski boot sole heights preventing wobbling between binding and boot Simultaneously the horizontal stability is increased to avoid accidental release at high backward lean forces on difficult World Cup slopes But that s not all For the real revolution in race bindings where was developed an intelligent Race AFD gliding element which moves together with the ski flex enabling constant contact between boot and binding in all flex situations Improved ski control and direct power transmission without wobbling between boot and binding guarantee precise ski steering exact trigger minimal response time resulting in the fastest runs for our World Cup Riders The new metal cage of the toe is certainly eye catching but also provides increased stability Improved Mx steadiness was also achieved by the new design of the wings and the innovative AFD element The narrower construction enables better angulations before snow contact and allows extreme turns What do our racers think They are excited The next World Cup winter season can get started we are ready POWER BRAKE 2 As true leaders we do not look back celebrating the successes of the past Therefore we keep on improving thinking ahead innovating the result Power Brake Brake arm claws touching the snow while skiing Brake arm claws stopping the perfect backwar
73. e boot meets the international standards and is free of any functional damage Take the binding parts out of the box and follow the steps on the instruction leaflet Determine the boot sole length with the rental boot indicator Pict 01 Art no 162 617 7 Simply lock it at the appropriate boot sole marking by closing the lever 310 mm First you have to open the toe lever and slide the toe on the rail from the front Pict 02 a we a 4 gt A z Y ro Finally check the forward pressure by placing a boot into the binding If you have followed all steps correctly the indicator should rest in the marked area Pict 07 If you have too much or not enough forward pressure check the settings at first If necessary adjust slightly at the heel and the toe Pict 08 Then check the forward pressure again 3 AFS JUNIOR ON DIN 7 5 AC amp DIN 4 5 AC MODELS The SX Junior Line is suitable for both adult type A and children type C boots the innovative mechanical Anti Friction Slider AFS automatically adjusts to the boot sole height compensating A C standards as well as height differences due to icing up dirt or boot wear Pict 09 If you want to increase the stability of your junior binding in combination with children type C boots you can replace the standard AFS with a vertically blocked AFS Art No 162962 which is for children type C boots ONLY All you have to do is to separate
74. e release retention system MAINTENANCE Inform every customer of the simple fact that periodic maintenance is needed If they dont bring their gear back for regular function checks it is unreasonable to expect it to work as designed Studies have shown that binding systems which have not been properly maintained have serious injury rates very much higher than those which have Following this simple logical guideline is the single most effective way to decrease serious injuries dramatically Have the system serviced by an ELAN certified technician once each 15 20 days of skiing or annually whichever comes first elam s ELAN Retailer Indemnitv Program Today s equipment may help reduce certain hazards involved in the sport but the risk of injury remains The ELAN Retailer Indemnity Program is designed to help formalize service procedures and minimize the risks to both you and your customer Under the plan ELAN will defend and indemnity the Authorized Retailer in bodily injury claims when certain conditions are met including following all ELAN required procedures The program benefits are not without limits indemnification is not insurance and it does not eliminate the need for a shop to have adequate insurance of its own But for the shop willing to make the investment in doing a quality job as an assembler of equipment systems from components it is a key element in their Risk Management plan This is only a summary of t
75. e themselves as Type Ill receive higher than average release retention settings This corresponds to decreased releasabilitv in a fall in order to gain a decreased risk of inadvertent binding release Type III settings should not be used by skiers of less than 22 kg 48 lbs If you are unsatisfied with the release retention settings that result from your classification please mention this to your binding technician NOTE If the skier reports release retention problems see the chapter trouble shooting release retention problems page 74 in the manual Skiers who desire release retention settings lower than Type I may designate themselves 1 Type I is inappropriate for skiers 17 kg 38 Ibs or less Type 1 Move up the table one skier code Skiers who desire release retention settings higher than Type Il may designate themselves LL Type II Move down the table three skier codes Skiers may select skier type designations that are different for twist and forward lean In such a case the selection shall be indicated by a slash separating twist and forward lean selections in that order for example K L K for the toe and L for the heel elam s RELEASE RETENTION Adjustment Table NOTE The initial indicator values found in this table are only the starting point in the binding setting process The initial values may need to be modified in order to achieve the correct measured release values AE sken cm CODE
76. e unaffected long term performance of the new FUSION and QUICKTRICK binding models the toe and heel guides can be exchanged or retrofitted These features ensure that steady function is guaranteed even after massive use in rental Art No 162950 Play Compensator PR TOE ABS Art No 162955 Play Compensator PR TOE AFS Art No 162951 Play compensator PR HEEL To change the inserts just slide toe and heel off the rails and replace them with new ones Pict 02 Lubricate the new inserts with grease clean the track and slide toe and heel back in its original position on the rails Za aa HEEL INSERTS FOR RACE PRO HEEL Open the heel locking lever and pull off the heel backwards Remove the inserts and mount the new ones Art No 162803 Pict 03 Lubricate the new inserts with grease clean the heel track and slide the heel back into the track Lock the locking lever into the same position it was before 7 LONG amp SHORT SCREWS Junior Bindings DIN 7 or 7 5 are delivered with screws for Standard FAT Ambition amp Adrenalin skis groups G3 amp G4 penetration depth 6 mm If they are Drill Template Drill Template Drill Template mounted on skis groups G1 amp G2 then the screws have to be 59 108 mm 104 154 mm 75 125 mm replaced with longer screws penetration depth 8 mm 83 132 mm 128 1 8 mm 99 149 mm 8 TAPPING ELAN recommends tapping the drilled binding holes of any ski before mounting Of cou
77. elease clamping handles thus attaching the template to the ski Check the boot midsole mark with template mark If they are not the same use the boot midsole mark to align the template with the ski mounting mark NOTE Keep in mind that some ski manufacturers do not use the center of boot sole location method always follow their instructions 4 DRILLING THE HOLES For ELAN skis Refer to the Drill Bit chart on Page 8 Other skis If not otherwise specified by the ski manufacturer use a 4 1 x 9 0mm drill bit Use a 4 1 x 7 0mm drill bit for skis group G3 8 G4 Drill the holes using the appropriate drill bit If required by the ski manufacturer tap the holes After drilling place a drop of glue in each hole It lubricates the screws and seals the holes Pict 01 A 5 MOUNTING 5 1 FOR ER FREEFLEX EVO PRO Place the pre assembled heel over the prepared holes Pict 02 and tighten the screws in a cross pattern A WA e Then attach the AFD to the toe and check if the AFD has snapped in in its specific position Pict 03 and 04 elam gt Then you have to place the pre assembled toe over the holes ATTENTION First you have to tighten the screw in the center the number has to correspond to the centimeter mark from the template To fix it you have to hold the bands together and tighten the screw carefully After this align the toe over the holes and fasten the screws in a cross pat
78. elected Reference Boots Bindings that fail go through a troubleshooting procedure see page 4 to identify and correct the deviation or malfunction If this procedure does not correct the problem the binding is removed from inventory All rental boots new and used are 8 visually inspected for damage wear contamination broken or missing parts or inferior materials at contact points with the binding In addition one boot per cell is tested for boots that are new to the rental inventory A cell is all boots of the same make model age and shell size A random selection of 5 of all boots previously accepted into Inventory is also tested Tests are performed with a test device and a pair of specially selected reference bindings If a boot fails all boots from that cell are then tested Boots that fail and cannot be repaired are removed from inventory INSEASON INSPECTION In season inspection are performed on complete rental systems to ensure that the equipment is adjusted appropriately and continues to function correctly Typically 5 of the rental inventory is tested during each two weeks sampling period The random sample is equally divided between equipment that is available for rental and equipment that has just been rented The equipment in the as rented category is from real skiers in the condition in which it is either dispatched or returned while the available for rental equipment may be set up for fictiti
79. eleted completely from our brake line running change Following changes are already done e No further production of all brakes in group E e 2new Brakes in group J with width of 100mm 163067 and 115mm 163068 will be added e 162764 SL Junior Brake 72 J was replaced by the 163058 SL Junior Brake 78 J e Adaption of the name e Junior will be deleted from the name e New group name will be SL Brake XX E Un e New sticker for E or J brakes Brake Od Periodoftramsition Final code 162642 SLBrake78 E p A 162755 SLBrake 90 E O qo too o 163017 SLBrake 100 E p AA 162929 Sl Brake 115 E SL Brake 90 E J 163067 SL Brake 100 E J 163067 e Brake 100 3 63068 SL Brake 115 E J 163068 stBraketis 3 IDENTIFICATION AND NAMING SYSTEM To make the brake binding allocation than as in the past we implemented the color coding system in 2013 14 In addition to the standard product labels of the spare brakes a color letter code is affixed on the brake boxes single and master packaging as you can see in the pictures to determine below All bindings packaged without brakes come with a similar sticker It is clear and quickly visible which brakes match with the binding E 1 For a binding with a red sticker A the dealer just has to look for a brake with a red sticker A in the proper width The segmentation and color coding system can be found in the ELAN brake line 2015 16 on the next
80. en fastened tightly e Has the forward pressure setting been controlled e Has at least one full adjustment been made using a representative reference boot including Release Retention setting and momentum test e Has the functional check been passed successfully Drill Template SR 2003 W 1 COMPATIBILITY Drill templates SR 2003 W are used for ESR models All ELAN adult bindings come with 8mm penetration screws and can be used with skis group G1 amp G2 Drill template SR 2003 W can be used for ski widths from 59 to 108mm For other skis use the template adapter set Art No 162569 With this adapter set ski widths from 45 to 132mm can be mounted NOTE The standard brake for all ESR 10 0 bindings is the POWER BRAKE LD 78 which can be used for skis up to 78 mm ELAN offers different types of brakes Refer to the brake overview on page 33 for brake and binding compatibility The description of the brakes always includes a number and a color letter code This number stands for the maximum ski width in the brake area and not in the ski center The color letter code defines the brake segment 2 POSITIONING THE DRILL TEMPLATE Open the clamping jaws 3 by rotating the clamping handles 1 and then place template correctly on the ski Align the boot midsole indicator 2 for the appropriate binding model or ELAN Plates with the midsole mounting mark on the ski Be sure the template is evenly seated against the ski s top sur
81. ength with the midsole mounting mark on the ski Fix it with a sticky tape and ensure that the template is centered and evenly seated against the ski s top surface After that you can mark the correct positions with a punch Pict 04 for front and rear position For Retail Version use the circle indicator and mark the closest centimeter position For Rental version use the quad indicators 3 DRILLING THE HOLES If not otherwise specified by the ski manufacturer use the 4 1 x 9mm drill bit for the toe and the heel track 8 holes if required by the ski manufacturer tap the holes After drilling place a drop of glue into the holes It lubricates the screws and seals the holes TA 4 MOUNTING Just start with mounting the heel unit of the binding depending on the version The mounting of the toe unit is the same in both versions 4 1 RETAIL VERSION HEEL UNIT Place the heel unit over the rear holes and fasten all screws in a cross pattern and continue at 4 3 4 2 RENTAL VERSION HEEL UNIT Start with placing the Demo Track over the holes and fasten all screws in a cross pattern Use the screws provided with the binding Insert the screw in the bottom side of the heel unit and slide the whole unit to the closest mounting position on demo track and fix it with the screw 46 4 3 MOUNTING OF THE TOE UNIT If you are mounting the RENTAL version the dampener has to be changed white damper out and
82. ent of an injury a Post Accident Report must be completed and retained if the shop is in possession of all components of the system If the entire system is not available for test it should be noted and all pertinent information such as equipment condition visual indicator settings and any equipment abnormalities should be recorded NOTE ELAN reserves the right to deny indemnity if ELAN requirements are not fulfilled Strict compliance by the dealer with all requirements as stated in the ELAN Binding Indemnification Agreement is a condition precedent to favorable consideration of a request for indemnity This is only asummary The precise requirements of the ELAN Binding Indemnification Program are contained in your ELAN Binding Indemnification Agreement elanr 7 85 ELAN Limited Warranty ELAN authorized distributor in the country in which this product was first sold at retail warrants to the first retail purchaser or user that this product shall be free from defecis in materials and workmanship This limited warranty as well as any implied warranty shall expire two years from date of the initial retail purchase In USA and Canada this period for retail bindings is four years from date of purchase or five years from date of manufacture whichever period expires earlier For rental bindings it is always two years from date of purchase For warranty claims or service the product must be returned at the consumer s expense t
83. er settings or maintenance may increase the risk of an injury Continued use of the skis will create wear and tear on the ski running bases and ski edges Have your system skis boots and bindings checked tested and serviced by a certified ELAN ski mechanic with proper mechanical tools annually or after every 15 to 20 days of use whichever comes first In case the skis do not have the proper service for repairing damage that could eventually result in delamination humidity penetrating the wood core or rust on the inside section of the steel edges of skis Skiing is a hazardous activity The sport of skiing and the use of ski equipment involve a risk of injury to any and all paris of the body Those dangers are inseparable even from a properly made product Skiing requires physical preparation technical skill and caution Using skis by children should be done only under child care supervision of certified ski instructor Use caution when handling the skis as ski edges are sharp and dangerous Use ski bag to protect your skis Store skis in a dry place at room temperature not exposed to direct sunlight or direct sources of heat Storing of wet skis in unsuitable rooms can result in rust on the steel edges which can again result in destruction or delamination The ski size should not be in discrepancy between the skier s weight and body height and the chosen ski design The skis are designed for certain loads only and the ski
84. er is responsible for any excessive force used The skier must use the proper skiing technique and to avoid to shock or overstress skis which could results in delamination and break The skier should not damage the skies striking with tails against a hard surface to remove the snow striking the two skis together scratches The skis are designed for skiing on snow which is why the skier must avoid shocks against rocks and other hard objects Always ski in control and stay within your ability Chose slopes and conditions for skiing carefully Follow posted warnings and instructions at the ski area Do not ski alone or when you are tired Do not ski while under the influence of alcohol or drugs Familiarize yourself with slopes and possible obstructions before skiing Take lessons from a qualified professional to improve your skills Remove snow and dirt clinging to your skis boots and bindings before stepping in Make sure that your clothing does not affect to the ski binding system or skis Each country could use different ski safety rules of conduct The customer must inform himself herself about those various 12 codes of conduct Keep strictly to the regulations that are in force in the ski resort FIS responsibility code of conduct in skiing 1 Respect for others A skier must behave in such a way that he does not endanger or prejudice others 2 Control of speed and skiing A skier must move in control He must adapt h
85. es Pict 01 E ange 4 MOUNTING 4 1 MOUNTING THE TOE Connect the plastic mid section 3 with the metal toe track 1 Place the assembled toe track 1 over the holes and drive the 4 four screws Open the hand lever 2 and slide the toe piece on from the front Adjust the toe piece to the desired SINGLE CODE position and close the hand lever 2 Pict 02 Ser Make sure that the lever snaps in place completely it may be necessary to slide the toe forwards and backwards slightly 4 2 MOUNTING THE HEEL Place the heel unit with its brake guide and track over the holes Tighten the screws in an X pattern elam s 5 FORWARD PRESSURE CONTROL Place a suitable reference boot in the binding using the SINGLE CODE for length adjustment and close it Then check the indicator see Pict 03 1 located at the rear end of the heel piece With boot inserted the pointer should rest in the marked area 6 ADJUSTMENT FOR ALL MODELS Find adjustment ranges and some handling hints in the section SvnPro SvmRent of the Technical Manual Take at least one reference boot satisfying all standards and free of functional damages to perform test adjustments with the binding 6 1 USING THE SINGLE CODE Adjust toe and heel to the corresponding alpha setting SINGLE CODE of the ski boot Pict 04 IF A BOOT OF UNKNOWN SIZE IS USED PROCEED AS FOLLOWS Place the boot in the toe cup Slide the heel piece forward until it
86. etailers previous seasons nn nn nn Page sEQUPMEN Rental FORM EE Page Use of the Equipment Rental Form re eeerere eae rerenan en A nAnn nn nnnnnnnannntn nn Page NO 0 0 ROCKER CAMBER ROCKER CONCAVE amp CONVEX VIBRATIONS ANALYSIS CHART FLAT METAL EE SHAPED METAL THINNER PROFILE is A TECHNICAL MANUAL SKIS 2015 16 Technical Information PRODUCT PREPARATION Product preparation is of a high importance for every user All Elan Skis are engineered and produced according to the actual ISO standards for alpine skis but even the best manufactured product with the best materials used will not perform well if minimal preparation and maintenance rules will not be followed 1 TUNING Each and every ski needs to be tuned properly and regularly to maintain its performance and safety Factory tuning is done on industrial machinery and cannot be copied manually Only authorized people with knowledge about the handling of service machines should service the skis Sintered bases require more frequent waxing but are harder and more resistant to impact damage extruded bases are less demanding as far as waxing is concerned but due to their sofiness may require more frequent repairs of impact damage Steel edges are to be sharpened once the edge grip gets less strong or the edges are damaged Even after only a few days of skiing on ice the skis can significantly lose their edge grip For the
87. face Release clamping handles 1 and attaches the template firmly to the ski NOTE Some ski manufactures do not use the center of boot sole location method Always follow the ski manufacturer s instructions 3 DRILLING THE HOLES For ELAN skis Refer to the Drill Bit chart on page 8 If not otherwise specified use an 4 1 x 9 0mm drill bit for skis groups G1 amp G2 Drill through the appropriate bushings Model Color of Bushing ESP 10 0 Vellow Drill Template Art No 162762 If required tap the hole After drilling place a drop of glue into the holes It lubricates the screws and seals the holes Pict 01 E ange 4 MOUNTING 4 1 MOUNTING THE TOE Place toe piece on the prepared holes and drive the screws 4 2 MOUNTING THE HEEL Place the heel unit with its brake guide and track over the holes Tighten the screws in an X pattern 5 FORWARD PRESSURE CONTROL Place a suitable reference boot in the binding using the SINGLE CODE for length adjustment and close it Then check the indicator see Pict 03 1 located at the rear end of the heel piece With boot inserted the pointer should rest in the marked area NOTE If the forward pressure is not correct readjust the boot sole length and check the SINGLE CODE Please make sure that no boot is placed in the binding during adjusting 6 ADJUSTMENT FOR ALL MODELS Find adjustment ranges and some handling hints in the section SvnPro SvmRent of the
88. fied in Table A for the binding type to be tested adult junior or child 2 Clean all five boots with a mild detergent and water 3 Adjust a rental binding to the release indicator setting specified in Table A for the binding type 4 Fit the binding to the boot and determine the Release Torque in all three directions of release forward lean and both directions in twist three releases in each direction 5 Average the Release Torque for CW clockwise and CCW counter clockwise twist release 6 Reject and replace any boot with a CW to CCW difference of more than 6Nm for adult boots or 4 Nm when testing child boot types 7 Rank the five twist results and select as the Reference Boot for twist the middle boot 8 Rank the five forward lean results and select as the Reference Boot for forward lean the middle boot PRE SEASON BINDING INSPECTION 1 Clean all boots with a mild detergent and water and The procedure that follows is an integral part of preseason A deele E damaged or missing paris maintenance It is also a good way to determine if visually CNECK E ful a Conformance with ISO and other applicable pa o a E ei DEES standards ISO 5355 If the boot contacts the binding brake or AFD in areas other than the designated 1 Clean areas of the bindings that contact the boot and contact points it may be incompatible with the perform all preseason binding maintenance binding 2 Visually or manually check b Bo
89. g or AFD the boot may returns the boot quickly and completely to center be incompatible with the binding 6 Verify elastic travel of the heel piece by lifting the boot f Mold flashings Flashing which can be seen or felt at while depressing the heel piece cocking lever and checking that the heel piece returns the boot quickly and completely to the latched position 3 7 Manually release the binding 3 times in each direction contact points with the binding brake or AFD must be carefully removed Remove from inventory all boots that have failed the 8 Lubricate all boot binding interfaces with a mild liquid Mela Caer detergent and water solution PRE SEASON BOOT SAMPLING 9 With the Ski Binding Test Device determine the Release Although sampling eliminates the need to test every Torque for each direction of release forward lean and boot before the season starts the sample chosen must both directions in twist be representative of the inventory 10 Record PASS in the binding s maintenance record if 1 For boots those are new to inventory or have never been Test Results are within the Inspection Range provided in inspected take a single boot from each cell Table A 11 Set the ski aside if the Test result in any release a cell is all boots of the same make model year and directions is outside the Inspection Range in Table A shell size 12 Follow Troubleshooting Procedure on page 74 for units 2 For used boots take a 5 b
90. hat failed NOTE On completion of the preseason inspection clean the liquid detergent from equipment and lubricate the binding before returning it to service The use of detergent is limited to testing only For maintenance cleaning please use WATER ONLY INSEASON SAMPLING AND INSPECTION The In season Inspection is a test of complete systems and all the procedures used by the rental staff to assemble and adjust the system The program uses random samples of rental inventory taken at routine intervals Any sampling program that gives every unit of inventory the same chance as every other of being picked is valid Sample Frequency Random sampling is conducted throughout the entire season Frequency is as follows 1 2 3 4 After 7 days of operation If the sample passes the next sampling is taken after another 7 days operation If two consecutive samples pass sampling frequency is increased to 14 days If a sample fails at any time daily sampling is instituted until two consecutive samples pass at which point weekly sampling resumes Facilities that have an average daily output of fewer than 160 rental skier days day averaged on a weekly basis may adopt an alternate procedure and sample over the sampling interval 5 of average daily output and delay evaluation of the inspection results until a total of 16 sampled units have been accrued However if single class Il or class III deviation is detected at any ti
91. he play of the toe Adjust the AFS with the screw in the front so that the tester is still moveable but with a slight resistance In this case you reached a gap of 0 5 mm between AFS and the boot Pict 15 If the tester is not moveable the gap is smaller than 0 5 mm if you feel no resistance the gap is more than 0 5 mm In both cases vou need to re adjust the AFS Pict 16 NOT OK 6 FORWARD PRESSURE Check the forward pressure bv placing a boot into the bin ding If you have followed all mounting steps correctly the indicator should rest in the marked area and you are ready to go Ca If you have too much or not enough forward pressure check the settings and if necessary re adjust the heel Then close the lever and check the forward pressure again Now it should be okay 7 ADJUSTMENT OF THE RELEASE VALUES The release values of the toe and heel should be determined by height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws at heel and toe unit ELAN recommends adjusting these settings by hand with a manual screwdriver We also recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US NOTE Release Retention settings above a release moment of 100Nm at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skier
92. he ELAN Retailer Indemnifv Program complete requirements are listed in the current ELAN Binding Indemnification Agreement You should read this Agreement carefully Retailer benefits under the terms of the plan are based in part on the adequacy of the service work performed by the mechanic For this reason thorough employee training is essential These manual and technical seminars are presented by ELAN to help define appropriate shop procedures It is the responsibility of the ELAN Authorized Retailer to see that all technical and product information materials provided bv Alpina Sports Corp USA ELAN Sports Inc Canada are ordered and available in their shop This should be done with the aid of vour ELAN Representative while placing vour ELAN preseason binding order Competition bindings are intended oniv for high level competitors who have special requirements that do not applv to recreational skiers Anv transaction involving competition bindings must include a warning and assumption of risk agreement signed by the skier that acknowledges the increased risk of using this equipment See the section in this manual regarding Use of Non Recommended Settings page 89 THE ELAN RETAILER INDEMNITV PROGRAM APPLIES ONLV TO THE FOLLOWING BINDINGS COMPETITION ER 20 0 x FREEFLEX EVO ER 16 0 x FREEFLEX EVO RACE ER 17 0 FREEFLEX PRO ER 11 0 FREEFLEX PRO ER 11 0 FUSION ELX 14 0 FUSION ELX 12 0 FUSION ELX 12 0 FUSION WB95
93. he sole hold down of the heel as it opens and closes BRAKE Press the step on plate 1 down by hand The brake arms 2 must close and open automatically to the braking position when the step on plate is released Pict 05 64 LATERAL ELASTICITY OF THE TOE Press the boot laterally outward The binding must re center the boot easily and quickly from a 15mm lateral displacement 8 FINAL CHECK e Has the proper mounting point been selected e Have all screws been fastened tightly e Has the forward pressure setting been controlled e Has at least one full adjustment been made using a representative reference boot including Release Retention setting and momentum test e Has the functional check been passed successfully Mounting ELAN Bindings on Plates 15 16 All ELAN PLATES are pre mounted on ELAN skis and they have holes to mount on bindings 1 COMPATIBILITY All listed ELAN screw on binding can be mounted on ELAN plates in next way RETAIL ER 17 0 FreeFlex Pro ER 11 0 FreeFlex Pro ER 11 0 Attack 18 X Attack 16 Attack 13 EP 14 0 WC EP 9 0 EP 9 0 EP 11 5 DUO EP 11X Attack 11 EFS 10 0 EL 10 0 EL 7 5 AC EL 4 5 AC NO plate RENTAL ESP 10 0 EP 9 0 ESP 7 5 AC EP 9 0 ESP 4 5 AC NO plate ESR 10 0 EP 9 0 2 MOUNTING BINDINGS ON PLATES All ELAN binding and plate combinations accord to chart on the next page with ELAN skis are possible with the standard brake For mounting juni
94. i Page s WOKSNOD TOOS SA AMS dd Page Mounting Bindings and Plates s Pprlhlemplale S0 1066101 aia Page DH Template 92W E FAT ni e f oie Page Drill kermplotetA aromatika a E ia tit Page s br Templates ANDION EE Page s Dr Tem plate Attack DEMO aaa Page DOM kotla o DA EE Page DMT mate RACER LATE de Page Mounting instruction Fusion oooicinanninniicnninnannccaa carr Page Mounting instruction QT Adult bindings cccccooonccnncccccnononccnnnnnnnnnncnnnnnnnnnncnnnnnnnonnnnnnnnnonnnanennns Page Mounting instruction QT Junior amp Lady bindings Page Drill Template SP 2003 W and SP 2003 FAT ocooooccncnnncnnnnccnnnnononnnaconnnnonnnnncnnnnnnnnnrnnnnnnnnnnnnnnss Page Drill Template Sit 20038 EE Page Mounting Elan Bindings on Plates at ias Page Binding Plate Coordination H RE Page ELAN Brake MaX E Page BOCIANA anie TOSIN WE Page Maintenance ano Sence u a Page Troubleshooting including Rental non Page Adjustment s GAS I 0 WE Page Release Retention Adjustment Table nn Page Release Retention nn nn nn RR rn Page SymPro A SymRent on the Shop Floor Page Dealer Service Information s jBlafCortilicatlom HEegmremen darian Page s laminaemmiv Ee le Page ELAN Limited Waranly EE Page RISA Ee Eet EE Page Use of non Recommended Settings srna nn Page s PostAccident Inspection Report EE Page System Performance Repol ui Ee Page Appendix The Binding List for R
95. ibio WaveFlex 82 XTi COLLECTION 1213 Amphibio WaveFlex 14 COLLECTION 1314 Amphibio 14 Fusion SLX Fusion Delight QT Honourable mention COLLECTION 1516 Amphibio 16Ti2 Fusion Race SLX ered oute section ofthe ski for easy a camber in ide section for edge grip with G scht precise t turn entry and a concave tail for a qui ick exit from turns FRONT Precise entry Io ke LL Lu el KE E O D O ES LLI Duluan sea LHDIU Ve BACK Quick exit The first ski with 4 dimensional technology Content Technical Manual SKIS lan SKIS CCOMOIOGICS E Page Technical INTORMALOMN aa a a ru o on Page MOUATNAG POSITIONS TOK SKI siria Page IMSTFUCTIONS e e tee War a EE Page Technical Manual BINDINGS Features amp News Sr WING VS OPE ORO io dna dass asa O RG Ut ira E o RO ae a Page S ANDION non Page Gage EE Page Gu re Page AAPP eege Page Technical Information Parts Reference Chart Retail ccccccssssccccesssecceeceeceecceeeececeseaseceeceaeeeessaaaeeesseseeeessaseesssaaas Page Parts Reference Chart AAA Series EEA AA encerrar an cer ee aaa eeranaaaana Page u Dala Binama Line Rea ssa ai Den a ITS add Page s Parts Reference Chart Rental id ae Sanat ada EE ege Page s Dadla bindiig EE Page Rental SymPro ESP SymRent ESR i iet ig i nala Page s Spare Parts handling WED ais Page h JEAN BAKE ONG geasagan a a A bdak j
96. ible The new OMS Spare Part Management on line WEB access offers all relevant information about ski bindings technical data and their spare parts at a glance and just one click away Extensive information is available via the new OMS spare part system Starting with the appropriate drill template right up to screws and spare parts related to a specific binding model for example different brake types plus all parts can be directly identified by model Pictures and colored marks provide simple navigation tools and easy recognition of selected paris LOGIN Run your browser type in address field http elan head com and you are ready to go Pages are protected To access type User name spare elan Password omsnew You can download complete User Manual from web page www elanskis com under DEALER MEDIA INFO lia o http dealermedialogin elanskis com M Remember ME TWO DIFFERENT MODES You may navigate through the Spare Parts OMS via two different modes 1 Product view mode q 2 Spare Part view mode ZE um With the product view all existing spare parts related to s ge a specific binding model can be identified In the spare part view all spare paris are listed with their designated use me dec a A sa uso a DE G mai 2012 2013 2011 2012 2010 2011 ftps dar haw com icms rd ch fps 144067 P IE tan oms File Edit View sote Taqa Help SPARE PART VIEWER The Spare Part Viewer explains all
97. if customers own their own skis with bindings or skis and bindings if the customers own their own boots Additionally some shops utilize on hill demo days as a means by which new producis can be tested and evaluated by potential buyers In order to offer these skiers the same level of care as that afforded under the preceding procedures the following guidelines should be used RENTAL OF SKIS BINDINGS ONLY CUSTOMER OWNED BOOTS Although the retail test procedure may be applied in this case it is often impractical to require actual system testing especially in on hill situations In lieu of retail testing the following procedures may be employed LF The ski binding system to be rented or demoed should be tested pre season using a boot which passes the ELAN Boot Visual Inspection The skier s boot should also pass the Visual Inspection If any questions exist regarding the quality of the boot retail type testing should be used The binding should be adjusted and its indicators set per current ELAN recommendation A full record noting appropriate customer information and binding settings should be kept by the individual or organization responsible for the adjustment After seven days of use the ski binding system should be tested according to the In Season Inspection Procedures previously described NOTE for U S and Canada Signatures by both the customer and ELAN Certified Mechanic are required o
98. in picture 66 Fix the strap with the Velcro fastener on your leg and use the carabineer to connect strap and hanger again 4 9 3 SPARE PARTS FOR ADRENALIN Changing AFS Metal Pro Art No 162984 Slide the AFS by turning the adjustment screw to highest position Take off the old AFS pa Bring the new slider in position Make sure that AFS is positioned on the two side rails and the guide screw of the binding matches the screw nut at AFS Therefore press the screw from the bottom up and slide the AFS to rails at once Make a readjustment of your sole height as described before page 42 43 44 Changing the climbing aid set Art No 162892 The climbing aid includes 1 wrench 2 screws 2 fixing parts and 2 climbing levers First open the ascender lock and slide the heel housing from the platform Remove the fixing screw with the added wrench on the top of the platform and furthermore the fixing part and the climbing lever form the bottom Pict 24 Put the binding to a straight position Insert and click the new paris as show in picture 70 into position use the 13 climbing position Picture 70 shows the right position of the lever the flatten part indicator has to be on the bottom side Fasten the screw and check the all 3 climbing positions Slide the heel housing with the brake from the back and lock it at the appropriate boot sole marking 10 FINAL CHECK e ls the proper mounting poin
99. inding 2 Add the thickness of the components you want to mount ski plate binding 3 Using the list below determine which ELAN brakes are standard on the bindings delivered 4 Find the value on the vertical axis which corresponds to the sum of the addition for the stand height 5 Follow the horizontal axis on the matrix to the right until you find the value which corresponds to the total weight on the horizontal axis 6 Ifthe point of intersection of the weight and stand height lies below the respective curve the brake will function properly 7 Ifthe point of intersection lies above the curve the brake must be replaced with the next stronger one 8 Ifthe point of intersection lies above the highest curve this combination of ski binding plate is not recommended In this case you have the following possibilities to come within the permitted range a Reduce the total thickness through a a thinner plate b an ELAN binding with less stand height b Reduce the total weight to a alighter plate e g a b anELAN binding with less weight c alighter ski c Use a combination of a b Have a look at all technical specifications about ELAN bindings and plates in chapter Technical Information page 22 and following this will help you in finding an accepted combination 3 Mounting Junior Bindings on Plates and on Skis group G1 amp G2 For mounting these bindings on plates or on skis group
100. ir device fulfills all ASTM ISO requirements Each device has its own unique features and some will fit your shop s needs better than others Therefore we can t recommend a single device as universally the best The following points however can be used as a guideline to getting the most out of your choice e Training is very important in the use of any device Read the instructions thoroughly and practice e To insure reproducibility from one technician to another a Multiple Operator Reproducibility Test should be performed by all users of the testing device This simply requires that all technicians join in a round robin exercise where each tests the same system with the same test device The goal is to verify that the testing techniques are the same and that all test results are comparable Speak with your testing device supplier for the details on how to conduct this program e Beware of black box calculations that may be performed by some electronic testers the calculations performed to arrive at an indicator value or determine an appropriate Torque Range could be based on old standards Check the current ELAN Adjustment Chart for applicable values e Periodic calibration of these devices is important and this information should be documented in your shop records e Most important never blindly trust the values given by any test device This is just one tool to use in your evaluation of a complet
101. is speed and manner of skiing to his personal ability and to the prevailing conditions of terrain snow and weather as well as to the density of traffic 3 Choice of route A skier coming from behind must choose his route in such a way that he does not endanger skiers ahead 4 Overtaking A skier may overtake another skier above or below and to the right or the left provided that he leaves enough space for the overtaken skier to make any voluntary or involuntary movement 5 Entering starting and moving upwards A skier entering a marked run starting again after stopping or moving upwards on the slopes must look up and down the slopes that he can do so without endangering himself or others 6 Stopping on the piste Unless absolutely necessary a skier must avoid stopping on the piste in narrow places or where visibility is restricted After a fall in such a place a skier must move clear of the piste as soon as possible 7 Climbing and descending on foot A skier either climbing or descending on foot must keep to the side of the piste 8 Respect for signs and markings A skier must respect all signs and markings 9 Assistance At accidents every skier is duty bound to assist 10 Identification Every skier and witness whether a responsible party or not must exchange names and addresses following an accident LIMITED WARRANTY ELAN warrants to the initial customer that Elan skis are free from defects in materials and wor
102. ith the two screws Ready 5 SOLE HEIGHT ADJUSTMENT The Ambition is designed to accommodate both type of boots ALPINE SKI BOOTS according to DIN ISO 5355 and TOURING BOOTS according to DIN ISO 9523 For proper function the height of the toe unit must be adjusted to the height of the boot sole ELAN recommends using the BOOT HEIGHT ADJUSTMENT TESTER Art No 162983 to get the ideal distance of 0 5mm between boot and AFS Turning the adjustment screw at the toe moves the unit up or down Place the tester on the AFS and enter the boot in the binding Lift the tip of the boot to take out the play of the toe Adjust the AFS with the screw in the front so that the tester is still moveable but with a slight resistance In this case you reached a gap of 0 5mm between AFS and the boot Pict 19 If the tester is not moveable the gap is smaller than 0 5mm if you feel no resistance the gap is more than 0 5mm In both cases you need to re adjust the AFS Pict 20 6 FORWARD PRESSURE Check the forward pressure by placing a boot into the binding If you have followed all mounting steps correctly the indicator and the heel housing should be on a flat surface If you have too much or not enough forward pressure check the settings and if necessary re adjust the heel 7 ADJUSTMENT OF THE RELEASE VALUES The release values of the toe and heel should be determined by height and body weight ISO ASTM method Set the
103. iver Do NOT use a screw shooter We also recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US 8 FUNCTION CHECK ENTRY EXIT Check to make sure that the boot does not catch on the heel hold down lug BRAKE press the brake pedal 1 down by hand The brake arms 2 must automatically return to the braking position when the treadle is released Pict 08 LATERAL ELASTICITY OF THE TOE Press the boot laterally outward The binding must re center the boot easily and quickly from a 10mm lateral displacement 9 FINAL CHECK e Has the proper mounting point been selected e Functional brake test passed e Have all screws been fastened tightly e Has the forward pressure been properly set e Are the release values of the toe and the heel properly determined and set e s the instruction for use booklet ready to be handed over to the consumer elam s Drill Template RACEPLATE 09 DACHPLATE OS mp tz ue usa Drill Template Art No 162902 1 COMPATIBILITY DRILL THROUGH THE APPROPRIATE BUSHINGS Presently the drill template RACEPLATE 09 can be used for PLATE POSSITION Color of indicator Eae lep 44 wc 290 350 mm SILVER Drill template RACEPLATE 09 is for mounting of both EP 14 WC RDX and EP 11 5 DUO Junior It can be used EP 14 WC 260 320 mm GOLD for ski widths from 59mm to 108mm For other skis use the tem
104. just touches the boot Close the binding and check the forward pressure 6 2 ADJUSTING THE RELEASE VALUES The release values at toe and heel should be determined bv height and bodv weight ISO ASTM method Set the binding accordingly with the adjustment screws We recommend the use of a calibrated testing device and that vou keep a written record of whether the system passes or fails requirement in the US NOTE Release retention settings above a release moment of 100Nm at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skiers own risk 7 FUNCTION CHECK Before the newly mounted ski equipment is exposed for rental use please perform a complete functional check NOTE In some countries USA rental equipment has to pass a Pre Season Test See the Rental section of this manual 62 EASY ENTRY AND EXIT If set properly the boot should not catch on the sole hold down of the heel as it opens and closes BRAKE Press the step on plate 1 down by hand The brake arms 2 must close and open automatically to the braking position when the step on plate is released Pict 05 4 dem LATERAL ELASTICITY OF THE TOE Press the boot laterally outward The binding must re center the boot easily and quickly from a 15mm lateral displacement Model SP 7 5 AG and SP 4 5 AC 10mm 8 FINAL CHECK e Has the proper mounting point been selected e Have all screws be
105. kmanship for a period of 2 years from the date of sale to the initial customer For rental skis the warranty period is 1 year from the date of initial purchase ELAN disclaims all other warranties express or implied Customer s sole remedy under the warranty is limited to the repair or replacement at ELAN s sole option of the product or parts thereof Customer should return the product or parts and proof of purchase to the place of purchase for warranty service THE WARRANTY CLAIM WILL BE ACCEPTED IN CASE e The proper warranty claim procedure has been observed e The customer submits evidence justifying the claim Such evidence can be returned product with defect and the invoices indicating the date of the sale to the customer e The warranty term period has not expired e The ELAN s Quality Assurance Department finds out that the defect has not been caused by reasons beyond the producer s liability THE WARRANTY SHALL NOT APPLY IF THE CLAIM IS A RESULT OF ONE OF THE FOLLOWING REASONS e Damages due to normal wear and tear e Minor damages that does not affect function e Any damages caused by abuse or improper use e g striking with tails of skis against a hard surface to remove the snow striking the two skis together scratches overstress of skis or using excessive force on skis improper ski size improper binding mounting by person which is not certified ELAN ski mechanic shocks with skis against rocks shoc
106. ks with the ski s tip against hard objects any other impact caused by sharp items due to torsion compression a fall or an abnormal impact e Any damages caused by improper care or storage e g improper storage improper transportation improper maintenance no regular servicing repairing and tuning skis at certified ELAN ski mechanic previous repair by person which is not certified ELAN ski mechanic modification of the product e Any damages due to non observance of the instructions or restrictions for use of the products and for its maintenance as defined in product manual LIMITATION OF LIABILITY Your sole remedy under the Limited Warranty shall be limited to the repair or replacement at ELAN s sole option of the product or parts thereof In no event shall ELAN or its agents distributors be liable for any direct incidental or indirect consequential damages or for any cost of transporting or shipping the product whether the claim is based upon contract warranty negligence or product liability including without limitation loss to property loss of use of the ski or other property or other economic losses Neither ELAN nor any distributor or agent shall be liable for contribution or indemnification whatever the cause This warranty may not be assigned or transferred Some countries do not allow limitations or exclusion on warranties or on certain damages or remedies so the above exclusions and limitations
107. lowing are some communication techniques that have been found to be helpful e Post your shop s testing policy A clear statement prominentiv displayed will reassure customers that they re all receiving the same treatment Consider a text similar to the following Industry standards have defined shop testing procedures for your ski boot binding system We re proud to offer this service since it is in your best interest While even the best ski equipment cannot eliminate all risks of injury we strive to maximize your enjoyment of the sport by verifying the settings and function of your equipment The extra time and expense of system testing will pay off for you in a better skiing experience e Make your service shop a showplace Place your testing bench in a prominent location Many customers like to know what kind of work you re doing for them If you get a question offer to let the skier watch e Proudiv display diplomas and certificates received by your mechanics Make their expertise known to your customers e Above all don t apologize for testing It s a valuable and necessary service well worth the cost ABOUT TESTING DEVICES ASTM and ISO have defined specifications for ski equipment system testing devices Only those devices that meet these recognized performance standards should be used to test systems that include ELAN bindings You should make it the responsibility of your testing device supplier to verify that the
108. m and toe 64 mm e 7 toe positions e DIN ranges from 2 5 up to 13 that accommodate even high level skiers e Short lightweight heel track despite wide adjustment range e SINGLE CODE A 6 for ski boots from 263 391 mm sole length e Replaceable brake e Diagonal toe e Optimal for Carving skis minimized deviation between ski and boot mounting point 30 ESP 7 5 AC ESP 4 5 AC A child and junior model super convenient parent free operation Automatic toe and heel pieces accept child and adult boot sole dimensions giving you full utilization of your child junior ski inventory e SINGLE CODE a H for ski boots from 191 294 mm sole length SP 4 5 AC and f T for ski boots from 215 343 mm sole length SP 7 5 AC The Single Code in lowercase letter refers to children s boots whereas with capital letter to type A boots Adult e ONE TOUCH hand lever adjustment for toe and heel e Replaceable brake e Diagonal toe e For skis groups G3 G4 e DIN range 0 75 up to 7 5 SYMRENT ESR 10 0 A technically proven workhorse for the discerning skier who rents e DIN range of 2 5 up to 10 e Diagonal toe e Large 84 mm heel adjustment range e SINGLE CODE A V e Automatic toe and heel height adjustment e ONE TOUCH Hand lever adjustment for the heel e Replaceable brake Spare Parts Handling On Line WEB Searching for Spare Parts and technical data as simple as poss
109. may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary in different countries Elar 13 14 TECHNICAL MANUAL BINDINGS 2015 16 The unique positioning of ELAN bindings in terms of proper function has also been recognized by the independent TUV l Product Service era fte f x icherheit Institute Manufacturer HTM Sport GmbH A 2320 Schwechat Tyroliaplatz 1 Telefon 43 1 701 79 0 Fax 43 1 701 79 334 www tyrolia com elam s News 2015 16 FREEFLEX EVO Freeflex EVO race bindings are a rEVOlution in ski racing right from the start to the finish line Evolutionarv perfection in which our athletes instill their trust to reach their goals glorious moments and outstanding results Freeflex EVO reduces the impact on the natural ski flex to a minimum Decreased forward pressure completely redesigned roller pincer systems and wings plus an intelligent gliding element all add up to the rEVOlution of racing fastest time from the starting gate to the finish line with Freeflex EVO sz gt e a lm 18 gt il i gt o We A The new construction of the roller pincer system and its wings guarantee utmost stability The newly designed wings overlap better with the ski boot interface the innovative concept includes longer wings and is closer to the ski boot Therefore the ski boot is stable and fixed in th
110. me corrective action should be taken This alternative method is used with a normal weekly or daily sampling schedule but is inappropriate for a reduced schedule Sample Size Sample size is 5 of inventory but not less than 16 nor more than 80 units as noted in Table B Sample size may be based on average daily output if rental output drops below 50 of capacity over the sampling period The sample is taken at any time during the sampling interval or may be spread over the period The sample represents both inventory 80 available for rental and equipment in the condition in which it is returned with an equal number of units drawn of each group All units within such sample should be selected randomly INSEASON INSPECTION 1 Take a random sample of the rental inventory as determined by Table B see next page Take half the sample from inventory as it is either rented or returned and the remainder from inventory available for rental The returned samples are tested with the last costumer s data the other samples adjust to randomly selected skier data Consider already applied Correction Factors Wipe the boot clean and cycle the boot binding systems at least once in each direction Test sample units in Twist one direction only and Forward Lean Compare the Test Results with the Inspection Range for the appropriate Skier Code see ISO 11088 Release Retention Adjustment Chart page 76 If the results are within the
111. n all shop forms to qualify for the ELAN Dealer Indemnify Program elam s ELAN Certification Requirements This section must be read and thoroughly understood prior to completion of ELAN s Employee Training Documentation Form and viewing the 2015 16 ELAN Technical Videos At ELAN we realize that the quality added to our producis in your shop is every bit as important as the quality we build in at the factory The ELAN Retailer Indemnitv program which includes in depth technical training is a key element of maintaining consistent quality TECHNICAL INFORMATION Procedures for installation release retention adjustment testing troubleshooting and record keeping should alwavs be taken from the current season s ELAN Technical Manual EMPLOVEE TRAINING This manual provides a depth of information unprecedented in the industrv it is here to help vou fulfill the shop s responsibilitv to bring new emplovees to a basic level of competence lt also addresses our desire to provide information specific to selling installing and function checking and maintaining ELAN products We hope vou will use it as part of a well planned and professional emplovee training program which goes far bevond properlv installing bindings Done well it will translate into consistent qualitv and the high level of satisfaction vour customers deserve Look at it as one of the first steps in vour Total Qualitv Management program NOTE Hands on training is the
112. n choose the precise fitting brakes in regard to freeride features with the ultimate ergonomic walking mechanism for the ski widths The ADRENALIN 13 can be maximum freedom on and off piste Overcome boundaries smoothly combined with brake widths of 85 mm 95 for a perfect ride mm 110 mm or 130 mm Brakes with a width of 95 mm 110 mm or 130 mm can be installed on the ADRENALIN 13 To find the right brake to your ADRENALIN have a look to the Brake line E ET o m M to r m w o o Another feature is the possibility to walk in the 0 position After release ELAN s climbing aid can easily be operated with a ski pole and it can be positioned in three different angles 0 7 and 13 for an optimal walking position This improves balance and a secure stand on your way to perfect skiing spois The climbing aid is also available as a spare part Art No 162982 SPARE PART AAA Series Powder Strap Art No 162981 1 Pair CA ANAS FREEFLEX AAA Series Powder Cord Art No HE 163025 1 Pair binding provides the approved Freeflex function which allows the ski to flex as it is designed to do so it can retain its natural dynamics Freeflex is enabled by the free gliding plate that runs within the titanal heel track and is supported by the center of rotation of the binding toe 20 FREERIDE FR PRO HEEL The ultra wide 80mm heel track makes all the performance difference needed
113. ncludes a number and a color letter code This number stands for the maximum ski width in the brake area and not in the ski center The color letter code defines the brake segment 2 ADJUSTING THE DRILL TEMPLATE There are two different mounting procedures for template 92 W one for FREEFLEX PRO and one for SCREW ON two piece bindings To adjust the template unlock the locking lever 1 by rotating it counter clockwise to the far left position ER FREEFLEX PRO NOTE Due to the center piece these bindings are limited to ski boots with sole lengths from 257 to 372 mm Place the ski boot in the template and push the template together until the stops 2 come against the ski boot sole Take the boot out of the template Position the locking lever 1 in the mid position then open or close the template to the nearest centimeter mark SCREW ON two piece BINDINGS Place the ski boot in the template and push the template together until the stops 2 come against the ski boot sole Lock the lever to the far right position to prevent length change and then take the boot out of the template ER 11 0 Attack 16 Attack 13 3 POSITIONING OF THE DRILL TEMPLATE Open the clamping jaws 4 of the template by rotating the clamping handles 5 and then place template correctly on the ski with the boot midsole indicator 3 aligned with the mounting mark on the ski Be sure the template is evenly seated against the ski s top surface R
114. o do is follow our simple procedure 1 Mount all bindings accordingly to the ELAN ESP procedures Pick a mounted sample binding of each model 2 Place a boot of each size in the binding and adjust forward pressure until correct 3 Open the heel and remove boot 4 Record the SINGLE CODE from the track that corresponds to the mark on the side of the heel housing The boot must not be in the binding when you read the code 5 Check each code again before marking all boots of this size with their SINGLE CODE pict below SINGLE CODE sticker set Art no 162 561 For this procedure the ELAN Rental Boot Indicator Art Nr 162 617 can be used RENTAL INSPECTION SUMMARY Since it is impractical to perform a full inspection each time a system is rented a routine of preseason and in season inspections has been developed to verify release indicator accuracy confirm correct equipment function and assure proper assembly and adjustment procedures by the rental shop staff Fully implemented the procedures that follow provide rental shop customers a standard of care equivalent to that provided retail shop customers under current ISO and ASTM standards The program is based on standards ISO 13993 and ASTM F1064 PRE SEASON INSPECTION Preseason inspections are performed on components of the release system bindings and boots All rental bindings new and used are visually inspected and then tested using specially s
115. o the place of purchase or to another authorized ELAN dealer or to the uthorized ELAN distributor in the country of purchase The Instructions for Use booklet the proof of purchase and proof of periodic service must accompany all bindings returned under warranty LIMITATION OF LIABILITY In no event shall ELAN be liable for incidental consequential statutory or exemplary damages whether the action is in contract warranty negligence or strict liability including without limitation loss to property other than the binding loss of use of the binding or other property or other economic losses ELAN shall not be liable for contribution or indemnification whatever the cause Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SERVICE UNDER THE ELAN WARRANTY Producis requiring service under the terms of the warranty should be dealt with as follows e Send the complete binding set to the authorized distributor where evaluation will be made and warranty action taken if required e lf aclear warranty situation exists and the shop wishes to replace the pair of bindings products out of stock for
116. ode This number stands for the maximum ski width in the brake area and not in the ski center The color letter code defines the brake segment 2 POSITIONING THE DRILL TEMPLATE Open the clamping jaws 3 by rotating the clamping handles 1 and then place template correctly on the ski Align the boot midsole indicator 2 for the appropriate binding model or ELAN Plates with the midsole mounting mark on the ski Be sure the template is evenly seated against the ski s top surface Release clamping handles 1 and attaches the template firmly to the ski NOTE Some ski manufactures do not use the center of boot sole location method Always follow the ski manufacturer s instructions 3 DRILLING THE HOLES ELAN skis refer to the Drill Bit chart on page 8 Other skis If not otherwise specified by the ski manufacturer for all ESP adult models use a 0 4 1 x 9 0mm drill bit for skis group G1 amp G2 For ESP 7 5 and ESP 4 5 use a Y 4 1 x 7 0mm drill bit for skis group G3 amp G4 f ESP 7 5 is mounted on skis group G1 G2 use a Y 4 1 x 9 0mm drill bit and replace the screws with longer ones If mounted on ELAN Plates replace the screws with longer ones SP 2003 FAT Art No 162879 for ski widths from 104 to 154 mm Drill through the appropriate bushings ESP 13 0 ESP 10 0 ESP 7 5 ESP 4 5 EP plates If required tap the hole After drilling place a drop of glue into the holes It lubricates the screws and seals the hol
117. on on the bottom of the telescopic tube Consider the right position as shown in Pict 23 Lock the crampon with the lever ready To remove just unlock the crampon with the lever and take off the crampon from the telescopic tube Pict 24 Cem 9 2 AAA SERIES POWDER STRAP Instead of brakes it is also possible to use the AAA Series powder strap for riding and hiking At AMBITION bindings it is required to use either brakes or powder strap To fix the strap on your binding take the hanger from the strap and fix it on the heel lever as shown in Pict 25 TI B al i Fix the strap with the Velcro fastener on your leg and use the karabiner to connect strap and hanger again 10 FINAL CHECK e ls the proper mounting point selected e Brake or Powder Strap mounted e Functional brake test passed e Are all screws fastened tightly e ls the forward pressure properly adjusted e Are the release values of the toe and the heel properly determined and set e Is the instruction for use booklet ready to be handed over to the consumer Drill template ATTACK DEMO s fajka s z i i A 1 COMPATIBILITY Presently the drill template ATTACK Demo can be used for ATTACK 13 0 DEMO All Attack 13 Demo bindings come with 8mm penetration screws and can be used with skis of groups G1 amp G2 If recommended by the ski manufacturer use shorter screws with a penetration depth of 6mm Therefore use the spare
118. on my personal decision to use them Competition bindings are not intended for use by recreational skiers because they have release and retention features that do not comply with national and international safety standards understand and acknowledge that competition bindings are made for high level competitors who based upon their personal experience have decided that they have special retention requirements that exceed the capabilities of recreational ski equipment and the standards that apply to recreational ski equipment understand and agree that any use of this equipment may significantly increase the risk of injury due to non release or other events and assume all risk of injury or death that may result from using competition equipment the undersigned have read and understand this liability release agreement and agree that it is binding upon me my heirs guardians administrators assigns and legal representatives If any part of this agreement is held to be invalid or unenforceable the remainder shall be given full force and effect Skier s Signature or that of the skier s parent or guardian Shop Manager s Signature Elar 89 90 POST ACCIDENT INSPECTION REPORT Date of Accident Workshop Ticket Skier Name Skier Phone Address Witness Name City State Zip Witness Phone Skier s Description of Accident and Injury Use Back For Additional Comments Description of System Rented Purchased Ski B
119. or U Flex concept COLLECTION 1314 Amphibio 14 Fusion Delight QT SLX Fusion Spectrum 115 ALU COLLECTION 1415 COLLECTION 1112 Amphibio WaveFlex 14 Amphibio Waveflex 82 XTI COLLECTION 1213 Amphibio WaveFlex 14 Ilumina Junior U Flex concept COLLECTION 1516 Amphibio 16Ti2 Fusion Delight ski amp ski boot set Spectrum 95 Carbon product design award universal design 2013 ti COLLECTION 1213 COLLECTION 1112 COLLECTION 1314 COLLECTION 1516 Amphibio WaveFlex 14 Amphibio WaveFlex 14 Delight QT Amphibio 16Ti2 Fusion COLLECTION 1213 COLLECTION 1415 Amphibio WaveFlex 14 Junior U Flex concept COLLECTION 1516 Amphibio 16712 Fusion DESIGNPREIS ricci More j SILVER NOMINEE 2013 l _ INNOVATION an COLLECTION 0708 COLLECTION 1213 COLLECTION 0607 COLLECTION 1112 Speedwave series Amphibio Waveflex 14 Speedwave series Amphibio Waveflex 14 Amphibio WaveFlex 82 XTi Ilumina COLLECTION 1213 Puzzle TBT Ilumina COLLECTION 1314 Delight QT COLLECTION 1516 Delight 65 InTemp NNER CATEGORY RTS AND EQUIPMENT WI IN THE PLUS X AWARD High Quality COLLECTION 1011 WaveFlex 14 GOOD DESIGN COLLECTION 1011 WaveFlex series WINNER IN THE CATEGORY RTS Equipme PLUS X AWARD Innovation COLLECTION 0809 Speedwave series reddot design award winner COLLECTION 0708 Speedwave series COLLECTION 1011 Race SLX COLLECTION 1112 Amphibio WaveFlex 14 Amph
120. or bindings on ELAN plates you have to replace the pre mounted screws by screws of 8 mm penetration depth The right pullout strength can only be ensured with these screws NOTE Use only the pre drilled holes for installation do not drill holes into the plate to mount bindings of other manufacturers Determine the boot sole length with the Boot indicator and place the binding on the plate corresponding to the appropriate printed length markings Pict 01 and 02 310mm Mount the binding in accordance with the procedures in this manual MOUNTING ELAN BINDINGS ON RAISED PLATFORMS Please note the ELAN brake matrix on the next page There you will find a classification of all our brakes depending on stand height and weight A brake is permitted if the combination of stand height and weight hits the sector under the relevant curve If not the brake has to be changed by a stronger one of a higher category At all current ELAN ski sets with plate systems the included brakes fit these requirements If you are combining ELAN bindings and plates with product of other manufacturer please check the technical requirements of the ski plate binding combination at the ELAN brake matrix on page 67 There you will find out if the desired combination of ski plate binding is accepted or if you need to exchange the brake FOLLOW THE PROCEDURE BELOW 1 Add the weight of the components you want to mount ski plate b
121. ormation on which binding settings are based skier height weight skier type age boots sole length e A full description of the equipment being serviced or rented skis boots bindings including but not limited to brand model size and serial numbers e Skier code Initial binding release retention settings and final settings e Signed dated statement from the ELAN Certified Mechanic that all manufacturer s procedures have been completed and the signature of the mechanic who performed the service if they are different individuals e Anagreement dated and signed by the customer the language of which is substantially similar to the current ELAN form This agreement must include the following poinis e User verification of skier information e WARNING that there are risks of injury inherent in the sport of skiing and that the customer accepis those risks e DISCLOSURE of the equipment s limitations that it will not release retain or prevent injury under all circumstances and is no guarantee of the user s safety e RELEASE language whereby the user releases the retailer manufacturer and distributor from liability and damages to the fullest extent allowed by law e STATEMENT that no warranties of any kind are offered by the shop beyond those offered by ELAN e AGREEMENT that instruction in the use of the equipment has been received that the skier height weight skier type age boot sole length as well as
122. ot free of dirt or sole warp 1 2 CHECK MATERIAL e Binding contact surfaces require a high quality hard low friction material Check both lower shell and any separately attached inserts e f you can easily scratch the surface of the sole with your fingernail that s an indication of extremely soft material that can degrade system performance 1 3 CHECK CONDITION OF BINDING CONTACT SURFACES TOE AND HEEL e Any scratches or other roughness should not be deeper than 1 mm e Check for any rocks gum or other foreign matter stuck to the sole 1 4 VERIFY BOOT SOLE DIMENSIONS e Skiboots must meet international standard specifications e Usethe Boot Rental Indicator to determine whether wear is excessive The most critical dimension for ELAN bindings is the front surface and height of the boot toe Any boots worn past the indicated amounts should be repaired or not used with ELAN bindings Adult norm A min height up to here max wear up to here 68 Children norm C min height up to here max wear up to 2 BOOT INDICATOR Art Nr 162 617 This rental boot device is a multifunction tool 1 Sole length Put the boot in the device and slide the toe stop up to the boot toe Read sole length in the window used for ELAN rental bindings the SINGLE CODE see Pict 03 At 2 Bootsole wear The standardized interfaces contact boot sole with sole lugs are important in the functioning
123. ot material If the sole at the contact points with a AFD condition b Brakes function c Release indicator readability and travel d Screw tightness the binding or AFD can be scratched with a finger nail the boot may be of inferior quality and incompatible with the binding 3 Adjust each binding with the reference boot and then c Boot sole condition If the boot sole is damaged adjust the release value indicators to the specified value worn or contaminated at contact points with the found in table A binding or AFD in a manner which cannot be corrected the boot may be incompatible with the 4 Check that the heel track and toe track Single Code agree binding Verify boot sole dimensions with the sole length Single Code of the reference Boot O orward Nm Indicator Reference Torque Twist Nm Reference Torque F Inspection Range Nm Inspection Range Nm Twist G L m Children 260mm 23Nm 87Nm 20 27Nm 75 102 Nm 17 31Nm 64 120Nm Junior 300mm 165Nm 37 50Nm 141 194Nm 31 58Nm 120 229Nm Adult 320mm en 58Nm 229Nm 50 67Nm 194 271Nm 43 78Nm 167 320Nm Table A Preseason Binding Inspection 8 3 5 5 With the Reference Boot in the binding verify elastic d Brake compatibility with sole travel of the toe piece by striking the boot toe with a e Rubber and or metal sole protectors If such mallet or dead hammer and checking that the toe piece materials contact the bindin
124. ous skiers Only single skis not pairs are tested and testing at the toe is only required in one direction A count is maintained of test results which exceed allowable limits The magnitude and frequency of these deviations determines the frequency of future inspections Shops which fail an inspection must sample daily until source of the problem is found and corrected Then as inspection results improve the frequency of sampling and inspection is relaxed INSPECTION PROCEDURES IMPORTANT TERMS Correction Factor The value that must be added or subtracted from the initial visual indicator setting to bring the result within the Inspection Tolerance or Inspection Range Directions of Release Unless otherwise specified see In season Inspection the directions of release to be tested are forward lean in clockwise and counter clockwise in twist Test Device A device which meets ISO standard 11110 or ASTM standard F1061 and has been checked and maintained in the manner specified by the device manufacturer Test Result or Release Torque The middle quantitative value of three tests made in the same direction PRE SEASON TEST Reference Boot Selection The Reference Boot is a boot of a designated sole length which is otherwise typical of the boot inventory Use the procedure below if the boot inventory includes several models and a representative boot cannot be easily identified 1 Select five single boots with sole lengths as speci
125. ox do not move up or down the chart Move sideways Codes see page 75 on the same row to the nearest box showing a visual If the skier is age 50 or older or under 10 move up the indicator setting chart one Skier Code toward the top For skiers 13 kg 29 This value should be recorded on the workshop form Ibs and under no further correction is required under Initial Indicator Settings 76 RELEASE RETENTION 10 MECHANICAL SYSTEM TESTING Adjust the bindings toe and heel indicators to the Initial Indicator Setting Use a calibrated torque measuring device according to the instructions provided by the supplier Test that binding by releasing it at least once in all directions Three tests are required in each direction The middle quantitative value of the three releases should be used as the test result Using the previously determined Skier Code slide across the chart to the column representing twist torque reference values If the test result is within one torque value above to one torque value below the reference value it is in the Inspection Range These results are acceptable and no further adjustment is necessary If the test result is within two torque values above to two torque values below the reference value it is in the In Use Range The indicator value should be readjusted and the system retested so that it falls in the Inspection Range Record the corrected indicator value in the box for final release
126. page ear ATTACK 16 a hem o sadid Eisch f white D WR 244615 Color letter code sticker for spare brakes Color letter code sticker on new Color letter code sticker on all bindings and bindings packaging of the spare brakes without brakes w o brake Also the nomenclature of all brakes is standardized and includes all basic information These nomenclatures consist of a clear name a number what defines the maximum ski width at the mounting point and a letter what specifies the brake cluster 4 W O BRAKE BINDING MODELS ELAN is offering some binding models without brakes marked w o brake to avoid brake exchanges later on and to provide suitable brakes for different ski widths For these models you need to order appropriate brakes separately Please find all available spare brakes in the ELAN brake line overview on the next page 32 L ER 20 0 X Free Flex Pro RD STIFF ER 16 0 X Free Flex Pro RD STIFF ER 17 0 FreeFlex Pro ATTACK 18 ATTACK 16 ATTACK 13 AMBITION 12 AMBITION 10 ER 11 0 FreeFlex Pro ER 11 0 ESP 10 0 ESP 7 5 AC ESR 10 0 Attack 13 0 DEMO ADRENALIN 13 ELX 14 0 Fusion ELX 12 0 Fusion ELX 11 0 Fusion ELW 11 0 Fusion EL 11 0 Fusion EL 10 0 Fusion ELW 10 0 Fusion EL 10 0 NS eee TRICK ELW 9 0 ELW 9 0 QUICKTRICK TRICK 162942 DF162942000 SL BRAKE LR 78H BRAKE LR 78 EL 7 5 AC ez UU TRICK Me DFI be A WWW BRAKE LR 90 EL 4 5 AG ELAS AG QUICK TRICK O TRICK 162966 SP162
127. plate adapter set Art No 162569 With this adapter set EP 11 5 DUO you can mount skis from SJ to 132mm After drilling place a drop of glue into the holes It lubricates All Elan plates have predrilled holes the screws and seals the holes Pict 02 The following chart shows which ELAN bases and plates are suitable for the different ski groups G1 G4 wm a a2 3 09 ePi4wo2s0 a50mm x o o 0 ePi4wo2so a20mm x x o 0 nso x x 0 Jo x compatible FEL not compatible If bases and plates are mounted on other ski groups the penetration depth and the torque moment of the screws have 4 MOUNTING EP 14 WC RDX Suns 4 1 MOUNTING PLATE 2 POSITIONING THE DRILL TEMPLATE Place a washer on the outer outside holes and tighten the Open the clamping jaws 3 by rotating the clamping handles screws 4x Pict 03 1 and then place the template on the ski Align the boot midsole indicator 2 for the appropriate model with the midsole mounting mark on the ski Be sure the template is evenly seated against the ski s top surface Release clamping handles 8 4 lil Place a washer also on the outer center hole NOTE Keep in mind that some ski manufacturers do not use the center of boot sole location method Alwavs follow the ski manufacturer s instructions 3 DRILLING THE HOLES If not otherwise specified bv the ski manufacturer use a a 4 1x9 0mm drill bit for EP 14 W
128. quipment column mark if the equipment is rented or owned enter ID f or description Mark if the customer wants to insure his equipment In the weight column circle the group that contains the customer s weight In the height column circle the group that contains the customer s height Select the skier code closest to the top Move on the skier code column according to the skier type Move on the skier code column according to the age Circle the final skier code Enter the final skier code into the box on the left hand side of the form Circle the sole length column that contains the sole length of the boot used Circle the Initial Indicator Value Determine the ELAN Single Code and enter it in the box Mark if this is an Adult or a Junior Code Determine the Final Indicator Setting adjust the binding accordingly and record the settings on the form Confirm with your signature that you have adjusted the binding as recorded on the form See a sample on the next page It is mandatory that you follow the above procedure exactly Before dispatching the equipment make sure that the customer has read and understood the form initialed and signed the form in all necessary places If the customer requests special settings follow the procedures for RELEASE RETENTION Troubleshooting at page 74 Elar 95 EQUIPMENT RENTAL FORM PLEASE PRINT CLEARLV 12 09 Last Name First Name Sample Jennifer Address City Prov Stat
129. r Agreement and the ELAN Bindings Indemnification Agreement must be on file with Alpina Sports Corp USA ELAN Sports Inc Canada e Theshopmust adhere to 2015 16 ELAN procedures for selection mounting adjusting testing and or servicing of system components as detailed in this manual e The actual ELAN retention release adjustment or its equivalent must be used e An ELAN Certified Mechanic must properly mount inspect adjust and or service system components and or check to make sure all service adjustments testing and record keeping was properly completed e Mechanics must receive full training including hands on practice in the use of system testing devices as provided by the testing device supplier A multiple operator reproducibility test should be completed and resulis documented by the shop each season e The shop must maintain records of all retail rental testing and or service work for 5 years or for the length of the Statute of limitations in the state where your business resides whichever is longer Bear in mind that the statute of limitations for minors begins only when they come of legal age PAPERWORK REQUIREMENTS ELAN Retail Rental Workshop tickets have demonstrated their usefulness in the legal system and we strongly recommend their use At the very minimum records must contain the following information e Identification of shop and customer name address phone e Date of transaction or work e Inf
130. r Pict 12 5 3 2 SOLE HEIGHT ADJUSTMENT For proper function the height of the AFD must be adjusted to the height of the boot sole ELAN recommends using the BOOT HEIGHT ADJUSTMENT TESTER Art No 162983 to get the ideal distance of 0 5 mm between boot and AFD Use ATTACK bindings only with Alpine boots TYPE A If you want to increase the stability of your junior binding in Please stay in the marked adjustment range area Pict 16 combination with children type C boots e g for junior racing you can replace the standard AFS with a vertically blocked AFS Art No 162962 which is for children type C boots ONLY All you have to do is to separate the standard slider from the base plate Pict 13 Turning the adjustment screw at the toe moves the AFD up or down Place the tester on the AFD and enter the boot in the binding Lift the tip of the boot to take out the play of the toe Pict 17 Afterwards you can simply click in the spare slider Pict 14 Adjust the AFD with the screw in the front so that the tester is still moveable but with a slight resistance In this case you reached a gap of 0 5 mm between AFD and the boot Pict 18 MOUNTING OF JUNIOR BINDINGS ON PLATES AND ON SKIS GROUP G1 amp G2 For mounting junior bindings on plates or on skis group G1 amp G2 replace the pre mounted screws by 8 mm penetration depth screws Only with these screws is the right pullout strength guaranteed 5
131. r death to any user of any equipment listed on this form whether caused by NEGLIGENCE or any other cause further agree that WILL NEVER SUE this ski shop as well as the manufacturers and distributors of this equipment and that WILL DEFEND AND INDEMNITY them if any claim or action is pursued for any injuries damages or death relating to skiing snowboarding skiboarding or any related activities involving the use of this equipment Please Initial accept this equipment AS IS and with NO WARRANTIES express or implied beyond those stated herein and in the manufacturer s written limited warranty This document constitutes the FINAL AND ENTIRE AGREEMENT regarding this transaction and this equipment and it supersedes any and all other documents or oral statements If any part is found to be invalid or unenforceable the remainder shall be given full force and effect THIS IS A CONTRACT which provides a COMPREHENSIVE RELEASE OF LIABILITY but it is not intended to assert any claims or defences that are prohibited by law The specific legal rights of the parties may vary in different states and provinces READ CAREFULLY BEFORE SIGNING A signature of User or agent Date e Parent s signature if user is a minor Date Use of the Equipment Rental Form eos SS Ds A e 12 13 14 15 16 Verify that the customer has provided all required information Make sure everything is legible Under the e
132. rand Model Size V Serial Inv gt Boot Brand Model Size a A Binding Brand Model Size A A Condition of System Are the boot soles within industry standards Yes No Are all buckles boot adjustments functioning correctly Yes No Are the A F D s Intact Yes No What are the Visual Indicator Settings Toe Heel Is the Forward Pressure set correctly Yes No Is the Toe Height set correctly Yes No NA o o Do the brakes function smoothly Yes No Is the ski bent delaminated or damaged Yes No Describe Was the equipment returned to service post accident Yes No Mechanical System Testing Testing Device Last Calibration date Clockwise Ctr Clockwise Clockwise Ctr Clockwise Toe L _ Ro A Heel L o o H Background Shop Name Inspected By Inspector Signature Checked By Checker Signature SYSTEM PERFORMANCE REPORT Shop Name Phone Address City State Zip Date Report Completed d Workshop Ticket Inspector s Name A Description of System Ski Brand Model Serial Boot Brand Model Binding Brand Model B System Performance Boot Sole Length mm Condition Testing Device Chart date j In Use Torque Tolerance Forward Lean Measured Release Values Clockwise Ctr Clockwise Toe L Heel L Workshop Ticket Date f d Position Rented Purchased Size Inv Size Size Binding Indictator Toe L R Setting Heel L R Last Calibration date i d Twist Clockwise Ctr Clockwise R Appen
133. rand new ELAN binding can be tested and shown to a broad audience Only two easy adjustments one on the telescopic tube and one on the demo track are required to fit to different boot 4 90mm gt lengths without extra drilling m 1 1 85 105 125m AAA Series Powder Strap Art No AAA Series Powder Cord Art No 162981 1 Pair 163025 1 Pair CI Ay 18 ONE FOR ALL EASY ADJUSTABLE TELESCOPIC TUBE Additionally the AMBITION features a unique light weight telescopic tube which offers an easy adjustment opportunity to different boot sole lengths Thus with only one binding model it is possible to cover the entire range of different sole lengths from 260 mm up to 350 mm eis Gew ila 111 wm emm O ge Furthermore with the setting of the telescopic tube and through the compact mounting perfect binding positioning on your skis is improved and midpoint deviation is avoided FREEFLEX The approved Freeflex System which interacts with the AT Toe the telescopic tube and the AT Heel offers natural dynamics excellent downhill performance and therefore a superior ski touring experience ALPINE TOURING TOE This newcomer in the ski touring segment features the exclusive ELAN Alpine Touring AT Toe which can be easily adjusted to alpine and touring boot norms A 5 mm wide mechanical AFS gliding element secures constant release values also with rubber soles
134. retention settings If the test result value falls out of the In Use Range the system should be thoroughly inspected for the following a Correct forward pressure b Correct Sole hold down adjustment c Worn or contaminated AFD s d Out of standard boot soles No work can be performed on the system until these problems are corrected Check the heel for forward lean the same way determining the middle quantitative value of three vertical releases Adjust if necessary Record final indicator settings on the workshop form in the area for final release retention settings 2 RELEASE RETENTION Troubleshooting 2 1 IF THE SKIER REPORTS A RELEASE OR RETENTION PROBLEM e Re inspect the equipment to make sure that all components are in good condition and function properly e Test the system to make sure that it is calibrated properly e Have the skier use the Classify Yourself materials to make certain that the correct Skier Type has been selected If component inspections and a calibration check do not reveal a problem the skier may be requesting discretionary settings 2 2 INFORMATION FOR SKIERS REQUESTING DISCRETIONARY SETTINGS 1 Your normal release retention settings comply with ISO ASTM standards Although these guidelines may be inappropriate for some types of competitive skiing or competition training they are believed to provide an effective compromise between the release and retention needs of most recreational
135. rse there is a never ending discussion among the mechanics if this is really necessary But the pros are convincing e smooth and easy mounting e reduced risk of stripping a screw e same momentum adjustment of the screwdriver regardless of the ski material e increased mounting quality precision e fewer pull outs 9 TEMPLATE ADAPTER SET Adapter Set is compatible to all Templates By using the template Adapter Set Art No 162569 the mounting range of your template can be adapted depending on how you position Standard FAT Ambition amp Adrenalin the adapters on the drill template Drill Template Drill Template Drill Template WARNING Avoid dropping of the template The clamping 59 108 mm 104 154 mm 75 125 mm EE 45 94 mm 90 140 mm 61 111 mm YOU HAVE 3 POSSIBLE OPTIONS 10 RACING X BINDINGS Certain binding models are produced by ELAN each year for the exclusive use of qualified competitors under the supervision of ELAN Technical Specialists These bindings are not covered by either the ELAN Warranty or any Dealer Indemnity Program We recommend you decline to service them and warn against their use DIN settings over 10 do not satisfy the standard Protection assertions are not applicable Adjustments exceeding this range are made on one s own risk 11 CLEANING AND LUBRICATING Ski bindings need regular maintenance Proper function is no longer assured if this procedure is not followed periodically
136. s own risk 8 FUNCTION CHECK Check the function of the heel Make sure that the boot does not catch on the heel during entry and exit Check the brake function by pressing down the brake pedal 1 by hand The brake arms 2 must open to the braking position when the brake pedal is released Check the elasticity and retention of the toe by pushing the boot inward and outward The binding must re center the boot easily and quickly from a 15 mm lateral displacement 9 ADDITIONAL EQUIPMENT AND SPARE PARTS FOR ADRENALIN 9 1 ADRENALIN CRAMPONS ELAN is offering additional crampons for ADRENALIN Bindings Use the crampons in icy and hard snow conditions to provide safe climbing and a secure stance in any situation Be sure to use the right width 90 mm Art No 162977 105 mm Art No 162978 or 120 mm Art No 162979 MOUNTING Open the climbing aid and lift the binding Take the crampon and slide it to the fixing position on the bottom of the hiking platform Consider the right position as shown in Pict 19 Lock the crampon with the lever ready To remove just unlock the crampon with the lever and take off the crampon from the platform Pict 20 9 2 AAA SERIES POWDER STRAP Art No 162981 At ADRENALIN bindings it is required to use proper brakes It is also possible to use the additional AAA Series powder strap To fix the strap on your binding take the hanger from the strap and fix it on the heel lever as shown
137. se values of the toe and heel should be determined by height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws at heel and toe unit ELAN recommends adjusting these settings with a manual screwdriver Do NOT use a screw shooter We also recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US NOTE Release retention settings above a release moment of 100Nm at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skier s own risk 8 FUNCTION CHECK ENTRY EXIT Check to make sure that the boot does not catch on the heel hold down lug BRAKE press the brake pedal 1 down by hand Pict 21 The brake arms 2 must automatically return to the braking position when the pedal is released LATERAL ELASTICITY OF THE TOE Press the boot laterally outward The binding must re center the boot easily and quickly from a 15 mm lateral displacement junior bindings 10 mm 9 FINAL CHECK e Has the proper mounting point been selected e Functional brake test passed e Have all screws been fastened tightly e Has the forward pressure been properly set e Are the release values of the toe and the heel properly determined and set e s the instruction for use booklet ready to be handed over to the consumer Drill template ADRENALIN 1 COMPATI
138. st for the higher or lower settings bv signing and dating the workshop or rental form bv the reason noted next to the setting request The skier must also read and sign a warning release and indemnitv agreement identical to the one printed on this page In such cases the system will only be indemnified if all other conditions of indemnification are met and the signed warning release and indemnitv agreement are attached to the completed workshop or rental form Warning Release and Indemnitv Agreement hereby acknowledge that have been advised by the rental shop sales department etc that settings which have requested for my bindings Model is not the setting recommended by the manufacturer of the bindings for a skier of my height weight age and skier type understand and acknowledge that there may be an increased risk of injury or death to me as a result of my own personal preference for these binding settings To the fullest extent allowed by law hereby waive and release all claims arising from the use of the bindings and release from all liability the shop the distributor and the manufacturer their agents and employees and further agree to indemnify them from any and all liability or harm or damage of any kind whatsoever which may result from the use of these bindings by myself or anyone allow to use the bindings If am using Competition Bindings such as ELAN X bindings my doing so is based entirely up
139. standards and has no functional damage Determine the boot sole length with the Rental caliper Art No 162617 NOTE Keep in mind that some ski manufacturers do not use the center of boot sole location method Always follow their instructions 2 1 DRILL TEMPLATE Adjust the boot sole length on the template open it by pulling the locking lever 1 to the left position Slide the template to the right length position and push the locking lever 1 to middle position Slide the template to closest centimeter mark until it snaps into position Place the template on the ski and center the jig Therefore open the clamping jaws 2 by rotating the clamping handles 3 and then place the template on the ski Therefore select the right midsole indicator on the template Black for RETAIL and Red for RENTAL version align the indicator with the midsole mounting mark on the ski Paper template Art No 163011 Drill template Ambition Art No 163000 y A 13 17 js Q M a 10100 8 8 Ze KR oO ba Renta Pouten Fem AA Ambition Utiere Bao tenter eos re v v Release the handles and ensure that the template is evenly seated against the ski s top surface Select the right holes The front holes are identical for both versions Retail and Rental red silver bushings You just have to select the right bushings for the rear holes 2 2 PAPER TEMPLATE Align the boot midsole indicator RETAIL or RENTAL for the appropriate boot sole l
140. stment range Additionally we recommend that the skier s setting not be closer than one number from the minimum or maximum settings on the binding in order to allow for future readjustment e Are the mounting screw lengths appropriate for the ski being used 3 CHECK THE CONDITION OF BINDING e Are all paris present and in working order e ls the AFD surface smooth and secure If not it should be replaced e Are all mounting screws present or tight e Does the binding show signs of contamination e Has proper periodic lubrication been performed Dried out or corroded bindings can function improperly 4 RETAIL TESTING Completion and documentation of the following Retail Test Procedures is recommended for U S required under the terms of the ELAN Dealer Indemnity Program These tests should be conducted any time work is performed on a ski boot binding system that may affect its release values The procedure applies to all ELAN alpine bindings new as well as used 1 Follow ELAN procedures for inspection mounting adjustment and maintenance as appropriate 2 Confirm that toe and heel indicator values match those specified on the actual ELAN Adjustment Chart 3 Using a calibrated testing device according to its instructions for use exercise the binding by releasing it at least once in each direction clock wise and counter clockwise at the toe vertically at the heel Then measure Twist and Forward Lean Torque Values
141. t in the US NOTE Release Retention settings above a release moment of 100Nm at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skier s own risk 5 FUNCTION CHECK Check the function of the heel Make sure that the boot does not catch on the heel during entry and exit Check the brake function by pressing down the brake pedal 1 by hand The brake arms 2 must open to the braking position when the brake pedal is released see Pict 15 Check the elasticity and retention of the toe by pushing the boot inward and outward The binding must re center the booi easily and quickly from a 15mm lateral displacement 6 FINAL CHECK e ls the proper mounting point selected e Functional brake test passed e ls the forward pressure properly adjusted e Are the release values of toe and the heel properly determined and set e Isthe Instruction for use booklet ready to be handed over to the customer elam e Mounting instruction QT Adult bindings 1 COMPATIBILITY Presently the QuickTrick Adult plate can be used for next bindings EL 10 0 QT EL 10 0 QT WB90 QT Adult plate is suited for boot sole lengths from 260 to 380 mm All ELAN s QuickTrick Adult plates are pre mounted on skis 2 FIRST INSTALLATION Make sure that the boot is satisfying the international standards and has no functional damage Determine the boot sole length with the rental caliper Art
142. t selected e ls the Brake mounted e Functional brake test passed e Are all screws fastened tightly e ls the forward pressure properly adjusted e Are the release values of the toe and the heel properly determined and set e Isthe instruction for use booklet ready to be handed over to the consumer Drill Template AMBITION 1 COMPATIBILITY Presently the drill template AMBITION can be used for Ambition 12 Ambition 10 All AMBITON bindings come with 8mm penetration screws and can be used with skis of groups G1 8 G2 Drill template AMBITION can be used for ski widths from 75 to 125mm For other skis use the template adapter set Art No 162569 With this adapter set skis from 61 to 149mm can be mounted Alternativelv the use of the attached paper template is also an option NOTE There are different tvpes of brakes Refer to the brake overview on page 33 for brake and binding compatibilitv The description of the brakes always includes a number and a color letter code This number stands for the maximum ski width in the brake area and not in the ski center The color letter code defines the brake segment 2 POSITIONING OF THE TEMPLATE There are two ways to mount AMBITION bindings Either with the solid jig Art No 163000 or with the paper template Art No 163011 which is included in the packaging of each binding We will show both procedures First of all make sure that the boot is satisfying the international
143. ter 162983 34 Drill Template Selection 2015 16 All ELAN templates are equipped with extended clamping jaws and an enlarged range of the fixing mechanism The STANDARD fixing mechanism ranges from 59 to 108mm the ADRENALIN and AMBITION mechanism from 75 to 125mm and the FAT mechanism from 104 to 154mm For more versatility ELAN offers a template adapter set to adapt the mounting range of your jig see the page 71 DRILL TEMPLATE 92 W 162760 for ski widths from 59 to 108 mm DRILL TEMPLATE 92 FAT 162868 for ski widths from 104 to 154 mm BINDINGS ER 20 0 X Free Flex EVO ER 16 0 X Free Flex EVO ER 17 0 FreeFlex Pro ER 11 0 FreeFlex Pro ER 11 0 EFS 10 0 EL 10 0 ATTACK 18 X ATTACK 16 ATTACK 13 ATTACK 11 EL 7 5 AC DRILL TEMPLATE ADRENALIN 162976 PAPER TEMPLATE ADRENALIN 163010 BINDINGS ADRENALIN 13 Long ADRENALIN 13 Short DRILL TEMPLATE AMBITION 163000 PAPER TEMPLATE AMBITION 163011 BINDINGS AMBITION 12 AMBITION 10 DRILL TEMPLATE ATTACK DEMO 163009 PAPER TEMPLATE ATTACK DEMO 163015 M VAR tack demo a BINDINGS ATTACK 13 DEMO elam s DRILL TEMPLATE RACE 94 W 162761 BINDINGS EL 4 5 AC DRILL TEMPLATE RACE PLATE 09 162902 PLATES Raceplate RDX EP 14 WC Raceplate Junior EP 11 5 DUO DRILL TEMPLATE SP 2003 W 162763 for ski widths from 59 to 108 mm DRILL TEMPLATE SP 2003 FAT 162879 for ski widths from 104 to 154 mm B
144. tern 1 38 5 1 1 SOLE HEIGHT ADJUSTMENT FREEFLEX EVO For proper function of the Freeflex EVO binding the height of the Race AFD must be adjusted to the height of the boot sole ELAN recommends using the Boot height adjustment tester Art No 162983 to get the ideal distance of 0 5 mm between boot and AFD Use Freeflex EVO bindings only with Alpine boots Turning the adjustment screw at the toe moves the Wings up or down Place the tester on the AFD and enter the boot In the binding Lift the tip of the boot to take out the play of the toe Pict 08 MAX 5 NM Adjust the AFD with the screw on the top so that the tester is still moveable but with a slight resistance In this case you reached a gap of 0 5mm between AFD and the boot Pict 09 If the tester is not moveable the gap is smaller than 0 5mm if you feel no resistance the gap is more than 0 5mm In both cases you need to re adjust the AFD Pict 10 5 2 FOR SCREW ON two piece BINDINGS Hook the brake into heel housing and place the binding over predrilled holes and tighten the screws in a cross pattern 5 2 1 JUNIOR BINDINGS AFS JUNIOR ON DIN 7 5 AC MODELS The SX Junior Line is suitable for both adult type A and children type C boots the innovative mechanical Anti Friction Slider AFS automatically adjusts to the boot sole height compensating A C standards as well as height differences due to icing up dirt or boot wea
145. the holes It lubricates the screws and seals the holes elam A 4 MOUNTING Place the heel track assembly over the holes and fasten all screws in a cross pattern To Then you can place the toe assembly over the holes and fasten the two front screws lightly 1 2 turns After that you have to close the platform with the ascender lock and then tighten the front screws 1 Open the lock again and tighten the other two screws of the toe piece Now vou can mount the heel Therefore hook the brake into the heel housing Pict 10 Slide the heel on the platform from the back and lock it at the appropriate boot sole marking Pict 11 42 After that vou can close the ascender lock and vou are readv for the final adjustments 5 SOLE HEIGHT ADJUSTMENT The ADRENALIN is designed to accommodate both tvpe of boots ALPINE SKI BOOTS according to DIN ISO 5355 and TOURING BOOTS according to DINISO 9523 Please use the A Alpine and T Touring markings for rough adjustment Pict 13 For proper function the height of the AFS must be adjusted to the height of the boot sole ELAN recommends to use the BOOT HEIGHT ADJUSTMENT TESTER Art No 162983 to get the ideal distance of 0 5mm between boot and AFS Turning the adjustment screw at the toe moves the AFS up or down Place the tester Art No 162983 on the AFS and enter the boot in the binding Lift the tip of the boot to take out t
146. the standard slider from the base plate Pict 10 60 4 ADJUSTMENT OF THE RELEASE VALUES The release values at toe and heel should be determined by the height and body weight ISO ASTM method Set the binding accordingly with the adjustment screws We recommend the use of a calibrated testing device and that you keep a written record of whether the system passes or fails requirement in the US NOTE Release Retention settings above a release moment of 100Nm at the toe and 425Nm at the heel are higher than the international standards recommend and are used solely at the skier s own risk 5 FUNCTION CHECK Check the function of the heel Make sure that the boot does not catch on the heel during entry and exit Check the brake function by pressing down the brake pedal 1 by hand The brake arms 2 must open to the braking position when the brake pedal is released see Pict 12 Check the elasticity and retention of the toe by pushing the boot inward and outward The binding must re center the boot easily and quickly from a 15mm lateral displacement EL 7 5 AC EL 4 5 AC 10mm 6 FINAL CHECK e ls the proper mounting point selected e Functional brake test passed e ls the forward pressure properly adjusted e Are the release values of the toe and the heel properly determined and set e Isthe Instruction for use booklet ready to be handed over to the customer Drill Template SP 2003 W amp SP 2003 FAT S
147. ting technique Excessive boot sole wear or Clean repair or replace boot contamination Inadequate binding service lubrication Conduct recommended maintenance EN every 15 20 days of use Excessive in season class 1 or class 2 deviations Improper use of testing device Check calibration and operating technigue Indicator correction factor needed Test system according to pre season testing Define indicator correction factor for subseguent adjustments Incorrect template adjustment used Set template to proper length and SINGLE CODE on binding when mounting remount heel interferes with SINGLE CODE on boot Incorrect track guide scale chosen for Choose binding according to given given mounting position mounting position SYMPRO toe Toe locking lever not properly engaged Remove toe clean track Be sure toe wobbles in locking holes piece locks into place in this track Toe equalizing bridge in wrong Dismount place toe in correct position FREEFLEXdrill pattern not fitting position Drill template not locked Readjust drill new holes Rear locking lever not fullv closed or Lever should fullv engage locking teeth boot length exceeds adjustment range in slots on track or boot sole length exceeds binding range Reference boot contaminated or worn Clean or replace boot as indicated bv clean vs lube test result o Forward pressure set incorrectly Readjust to ELAN recommendations Binding fails pre season test release values too high or too low
148. tuning of Elan skis we recommend the following edge geometry Angle from base 1 0 5 Angle from side 1 5 0 5 2 DRILL BITS Proper binding installation is essential for the optimal performance of the product and proper binding function Follow the chart of catalogue ski models below regarding the diameter of the drill bit and depth of drilling Holes must be sealed with glue Please contact the local distributor for non catalogue models 4 1 x 9 0 mm SLX FIS GSX FIS FX SGX FX DHX FX SG Airline Ripstick FIS Bloodline GSX Team SLX Team GSX Master amp 25 RCG RCS RCX GSX SLX SL Ripstick SLX GSX SLR GSR Waveflex Amphibio 88xtii 82xti 12ti 13 14ti 16ti2 18xti SPECTRUM 115Alu 105Alu Carbon 95Alu Carbon Boomerang Puzzle TBT Sling Shot Speed Magic Insomnia Delight Twilight 76 93 6 x 9 0 mm all EXPLORE series all e Flex all Waveflex Amphibio 84xti 84ti 78ti 76 9 10 11 RSX Race Himalaya Alaska Alaska PRO Karakorum Lhotse Spectrum 85 Pinball Twist Inspire Ilumina Black White Magic Zest Zest Black White Twilight 84 90 Snow Snow White Black Perla Ilure Avidity Freeline Vario EXAR eRise 76 EXAR eRise 72 EXAR Race EXAR GX Explore Exar Pro 2140cm Explore Pro 2140cm My Own 2140cm Jett 2140cm Starr 2140cm Maxx 2140cm RC Race 2140cm Sky 2140cm Pinball PRO Team 2140cm Petit 2140cm 94 1 x 7 0 mm 93 6 x 7 0 mm Exar Pro lt 140cm Explore Pro lt 140cm My Own
149. ug Heel housing Adjustment screw Visual indicator ELX 12 0 FUSION ELW 9 0 QUICKTRICK MID PARTS 16 FREEFLEX PRO 17 FUSION lever 18 FUSION scale 19 QuickTrick lever 20 QuickTrick scale 21 FUSION central locking system 22 FUSION safety lever 23 FUSION locking lever Parts Reference Chart AAA SERIES Ambition 12 0 Adrenalin 13 0 Attack 13 0 DEMO Attack 18 0 X TOE PIECE HEEL PIECE MID PARTS 1 Adjustment screw 7 Brake pedal 22 Boot sole length scale 2 Visual indicator 8 Brake arms 23 Walking platform 3 Adjustment screw AFS AFD 9 Heel lever 24 Telescopic tube 4 Adjustment screw sole height 10 Heel cover 25 Length adjustment screw 5 AFS AFD 11 Heel housing 26 Crampon 6 Wings 12 Adjustment screw 13 Visual indicator oe 14 Ascender lock me es Ee 15 Climbing aid Attack Demo scale 16 Sole lug 17 Heel adjustment lever 18 Heel base plate 19 Demo track with fixing screw 20 Length adjustment screw 21 Dampener DEMO 29 Attack Demo scale elam s Data Binding Line Retail 2015 16 URE Toe Toe Model Z DIN kg Ibs Feature Toe AFD Hera system type eight COMPETITION T T e ER 20 0 0 FREEFLEXEVO 10 20 fom o7 vom 209 FREFFLEX PRO RAGEAFD 125 ma ER 16 00 FREEFLEKEVO 8 16 rom 79 rom 175 FREEFLEXPRO RAGEAFD 125 1 mae RACE Enmo La rma tomer ass 18 FULDAGONA 1x EE Ee U eee Q
150. uickTriek 0 from 57 QuickTrick QT JUNIOR ooo a E PEA IFP RR EFS100Wideso 910 iromst tomer TEFLON 12 FULLDIAGONAL sx eto 910 roma tomer TEFLON 12 FULLDIAGONAL SX AAA Series ADRENALIN 13 w o Short 4 13 from zl from 92 Hiking platform AFD metal 28535 rom ADRENALIN 13 wo Long 4 13 from 42 from92 Hiking platform AFD metal 28535 FRPRO ATTACK 18 X w o brake 818 from79 tom175 Lampe 120150 FRPROMA ATTACK 16 wo brake 5 16 tom s nomio msn 120150 mme ATTACK 18 wo brake 4 13 fom42 fome AFD metal 120150 FRPRO ATTACK 18 DEMO webrate 415 rom 42 momoe AFOmetal 190220 Immo ATTACK 11 wo brake 911 romar romer AFD metal 120150 FRPRo AMBITION 12 we brake 4 12 roma mens Teleseopictube as 40 mn SET Junior kid EL7SAC 275 2284 48187 TEFLON 12 FULLDIAGONAL SX Junior Kan ersas 1048 22106 memon te FULLDIAGONAL om M 6 Heel stand height I2Xefeji sole type Ramp angle mm Length adjustment range mm Brake Code Drill template Boot sole length mm Heel type Weight set Brake type PB RACE PRO 18 85 PB RACE PRO 18 85 RACE PRO RACE PRO A A 18 18 255 375 255 375 ADULT 92 W FAT ADULT 92 W FAT 3190 g 3190 g ada Wu RACE PRO IPB RACE PRO
151. ut not less than 16 or more which have been set aside and retest if changes in the than 80 random sample of the entire inventory see Table unit s condition or adjustment are made B Make sure that there is at least one boot from each 13 Record FAIL in the binding s maintenance record if after cell in the sample troubleshooting test results in any direction of release are PRE SEASON BOOT INSPECTION outside the In Use Range Replace the failed unit and retest before returning the ski to service The procedure that follows helps to assure boot binding 14 If after troubleshooting Test Results are outside the compatibility and boot interchange ability Inspection Range but within the In Use Range apply a NOTE when using Table A in the Boot Inspection Correction Factor to the unit and note the Correction procedures that follow the Sole Length and release Indicator Factor for that unit in the binding s maintenance record Setting columns should be ignored 15 If many bindings fail check the test device and reinsert 1 Randomly select a pair of bindings that have passed the the Reference Boot li necessary select another boot and preseason inspection from each binding type adult retest the bindings junior child PRE SEASON BOOT PREPARATION 2 Lubricate all boot binding contact points with a mild liquid detergent The procedure that follows is an integral part of pre season A 3 Without regard to whether the boot
152. ve to replace the pre mounted screws by screws with 8 mm penetration depth Only with these screws can we guarantee the right pullout strength NOTE Use only the pre drilled holes for installation do not drill holes into the plate to mount bindings of other manufacturers Determine the boot sole length with the Rental boot caliper and place the binding on the Plate corresponding to the appropriate printed length markings EM Mount the binding in accordance to the procedures specified in this manual elam s Mounting instruction FUSION bindings 1 COMPATIBILITY Presently the Fusion 4 system plates can be used for next bindings ELX 14 0 Fusion ELX 12 0 Fusion ELX 11 0 Fusion EL 11 0 Fusion EL 10 0 Fusion ELW 11 0 Fusion ELW 10 0 Fusion Fusion 4 system replaced the old Fusion 2 system in season 12 13 Systems are not compatible All Fusion 4 plates are pre mounted on skis 2 FIRST INSTALLATION Open the toe lever and slide the toe on the rail from the front ELX 12 0 Fusion Wide 88 Slide the toe towards tail At certain point the toe will stop then release the laver and push it into the end position v Open the heel lever forward pressure indicator and slide the heel on the rail from the tail 56 Slide the heel towards tip At certain point the binding will stop Ap CI e RC er e SE gt DEE A 3 ADJUSTING BOOT SOLE LENGTH Make sure that
153. with the manufacturer s recommendation for the skier s weight and level of skiing This is another area where regular maintenance is critical RACING X BINDINGS Certain binding models are produced by ELAN each year for the exclusive use of qualified competitors under the supervision of ELAN Technical Specialists These bindings are not covered by either the ELAN Warranty or any Dealer Indemnification Program We recommend you decline to service them and warn against their use In a similar vein some skiers may wish to use retention settings which are excessive DIN settings over 10 do not satisfv current industrv standards and should not be used Adjustments exceeding this range are made on one s own risk COMPLETING THE WORK ORDER WITH THE CUSTOMER It is critical that certain basic information be included on all shop work orders Once the customer has selected equipment or described the repair or service to be performed the technician must ask the customer to complete a portion of the Work Order Form which includes their Name Address Phone number Weight Height Age Sex and Skiing abilitv The skier must then sign indicating that thev have read understood and agreed to the terms of vour Rental Repair agreement this agreement must comply with ELAN Dealer Indemnitv Program requirements It is also important that the customer be informed that they will be expected to verifv in writing that the indicator settings agree
154. with what is written on the form and that thev have been instructed in the use and maintenance of their equipment and fullv understand it This procedure must be completed before the transaction is consummated Remember the customer has the option of going to another store if the terms of the contract are not acceptable to them and under no circumstances should the transaction go anv further without their signature The end user or their agent must sign the incoming work order elam e SHOP PROCEDURES SUMMARY For in depth details see the Binding Installation section of this manual e Follow ELAN procedures for inspection mounting adjustment and maintenance as appropriate e Confirm that toe and heel indicator values match those specified on the actual ELAN Adjustment Chart e Using a calibrated testing device according to the manufacturer s instructions for use exercise the binding by releasing it at least once in each direction clockwise and counterclockwise at the toe vertically at the heel Then measures Twist and Forward Lean Torque Values The middle quantitative value of 3 releases in each direction should be used as the test result e Compare Twist and Forward Lean test results with the System Inspection Ranges on the actual ELAN Adjustment Chart e After the equipment is adjusted to the skiers needs according to the manufacturer s standards the certified technician signs the form indicating that
155. y more direct power transmission and an ultimate skiing performance CRAMPONS Additional crampons are available as spare paris in widths of 90 mm 105 mm and 120 mm and provide safe climbing and a secure stand in any situation 90 mm Art No 162977 1 Pair 105 mm Art No 162978 1 Pair 120 mm Art No 162979 1 Pair tack ASTONISHING PARK amp PIPE ACTION The ATTACK binding designed for freeskiers captivates with its minimalistic design and combines perfect light weight control and versatile usage in one masterpiece With this new freeski binding you can enjoy park or half pipe just as high performance off piste skiing A perfect tool for all around skiers who are willing to attack Get ready for park half pipe amp on and off piste with the ELAN ATTACK binding models MODERN ARCHITECTURE The special Freeride FR Pro Toe with its horizontal spring reflects the modern architecture of the new ELAN AAA Series Furthermore it includes a super secure 77 mm metal Anti Friction Device AFD Metal which can be adjusted for all types of alpine boots Type A only The ATTACK 16 features the ELAN Race Pro Heel with a reduced stand height of only 17 mm for the ultimate freeski adventure PERFECT INDIVIDUALITY The built in AAA Series technology ensures high quality and perfect usability In regard to its clear design and its compact measurement the ATTACK model can be ideally used on ski widths from 80 mm and

Technical Manual (eng) - ELAN - Certification

Contents

Download Pdf Manuals

Related Search

Related Contents