Home

- ServiceNet - T

1. rvsMVS Messages and Codes 5 rvs Messages DF9O10I DF9011E DF9012E DF9013E DF9014E DF9015E DF9016P DF9017E DF9018E DF9019E f sid mn SESSION CONTROL TERMINATED SYSTEM sss USER uuu The task started for station sid initiating session mn terminated with system completion code sss and user code uuu A sid NO SESSION DEFINED FOR THIS STATION No entry is defined in the rvs sessions table for station sid A sid mn INVALID MODE The session identifier mn for the station sid is not defined in the rvs sessions table A sid mn SUBTASK ALREADY ACTIVE SESSION REJECTED The session mn to station sid is already active A new session mn to station sid will not be established F sid mn SUBTASK NOT ACTIVE There is no active subtask which supports session mn to station sid LU luname UNKNOWN SESSION REJECTED The station sid assigned to the VTAM luname tries to establish a session to rvs This request is rejected because no luname is specified in the rvs stations table A sid mn RPL CONTROL FIELDS xxxxxx request This message is generated after the SCIP exit of the VTAM control task has been activated The reason for acitvating the SCIP exit may be obtained from the RPL control fields xxxxxx Expected are the following requests BIND UNBIND SDT start data traffic CLEAR and RQR request recoverey request All other requests are denoted by U
2. x k NO ACTIVE SDS TASKS kk k RECORD DONE IGNORED xkkk RECORD IN HOLD STATE IGNORED x kk k TASK WITH KD RECORD ACTIVE kkkk SDS BUILD kkkk SEND REQUEST IN HOLD STATE PRIVATE KEY ERROR HOLD ERROR CHANGE KDRECORD SEND REQUEST IN HOLD STATE PUBLIC KEY ERROR HOLD ERROR CHANGE KDRECORD All message are protocol messages only DF5M25P NO STATION TABLE FOR SID The Send Dispatcher detects an error The record can not processed DF5M27I SDS TASK COULD NOT BE STARTED NOT ENOUGH MEMORY This message is issued by Send Dispatcher task when activation of further subtask is rejected because of storage shortage DF5M99P X ORT ACME 12345678 94 rvsMVS Messages and Codes 5 rvs Messages Internal trace message of Send Dispatcher DF5NOOI D SDS DRIVER TASK 277272727 22 2222222272722 2222272222220 This message will be issued by the D command For more explanation refer to message DF52011 DF5SN34I D VOLUME IS NOT MOUNTED DF5SN35I D FILE NOT FOUND ON SPECIFIED VOLUME This message is issued by the SDS Task if the file is not found on the volume specified in the KDRECORD Shown is the virtual file name DF5N35Z D PHYSICAL DSN VOLUME This message is issued by the SDS task if the file is not found on the volume specified in the KDRECORD Additional this message shows the physical datasetn
3. A REMOTE STATION NOT READY This message is issued by the rvs TCP IP task when a connect request has not completed successfully The remote partner addressed by IP address and TCP port did not respond A TCP IP SESSION LOST S This message is issued by the rvs TCP IP task when loss of a session has been detected All activities for this connection are terminated A READ COMPLETE S L DATA This message is issued by the rvs TCP IP task when a read macro has completed successfully The message displays the remote station socket number datalength and the first 4 bytes of the received data A INCONSISTANT DATA RECEIVED S EXPECTED LENGTH RECEIVED LENGTH This message is issued by the rvs TCP IP task when a received data buffer had a different length than indicated in its header The connection will be terminated A CANCEL COMPLETE S This message is issued by the rvs TCP IP task when a received data buffer had a different length from that indicated in its header The connection will be terminated The socket number is displayed A 2 IP ADDRESS Hi Hl PORT H HHHH This message is issued by the rvs TCP IP task when the open process has completed This message displays the own IP address and the own port number READ ERROR DETECTED LENGTH NOT POSITIVE This message is issued by the rvs TCP IP task when a read macro is to be issued The
4. AR records build See returncode values in message DF8583P For internal use only DF8546P D sid sesid NO AR KDRECORD BUILD RC nnnn 126 rvsMVS Messages and Codes 5 rvs Messages DF8550I DF8551P DF8552W DF85532 DF8561I DF8562E DF8563E DF8564E DF8565E DF8566E DF8568P DF8570E DF8571E DF85721 The FTP Server Task issues this message when checking of HFID records ended with error no AR records build See returncode values in message DF8583P For internal use only D sid sesid END OF FTP TRAILER FILE TRANSFER The FTP Server Task issues this message when sending of FTP Trailer control file is closed D sid sesid END TO END RESPONSE RECEIVED DSN dsn The FTP Server Task issues this message when an End to End Response EEID protocol unit is received In case of errors additional messages DF8552W and DF8553Z will be given D sid sesid UNKNOWN EEID RECEIVED DSN dsn The FTP Server Task issues this message when an End to End Response EEID protocol unit is received but the EEID can not be associated with a previous file transfer In the message is shown the file name indicated in the EEID protocol unit D sid sesid EEIDDATE gt The FTP Server Task issues this message when an End to End Response EEID protocol unit is received but the EEID can not be associated with a previous file transfer The message shows the received data in the EEID protocol unit starting f
5. This message is issued by the rvs APPC driver task routine The message is issued as a continuation to a VTAM request info message for APPC LU 6 2 support The message shows the primary and secondary return codes and an associated text explanation APPCCMD ALLOC FAILED FOR 2 2 RC xxxx SENSE xxxx This message is issued by the rvs APPC driver task routine The APPCCMD ALLOC was issued to start a conversation with a partner node but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information SENSE xxxx This message is issued by the rvs APPC driver task routine An APPCCMD SEND with CONFIRM or FLUSH option was issued in order to flush the send buffer and get an acknowledgement from the partner but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information APPCCMD DEALLOC FAILED FOR 2227272272 RC xxxx SENSE xxxx This message is issued by the rvs APPC driver task routine The APPCCMD DEALLOC was issued to stop a conversation with a partner node but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information APPCCMD REJECT FAILED FOR 2 RC xxxx SENSE xxxx This message is issued by the rvs APPC d
6. 094 098 0AO 0A4 0A8 OAC OBO 0B4 A data set is to be received in a remote station and transferred to a final destination This final station is not defined within the station table of the remote station A data set is to be received in a remote station but the originator of the file is not defined within the station table of the remote station A data set is to be transmitted via ODETTE FTP The name of the file does not comply with the coding rules of OFTP data set names A data set is to be transmitted via rvsMVS FTP A PDS file is to be sending but rvsMVS FTP does not support PDS file transfer A data set is to be transmitted via rvsMVS FTP Invalid format of HFID control record A data set is to be transmitted via rvsMVS FTP A file is to be received and catalogued after transmission but a file with the same name is already existing catalogued Receiving of this file will be rejected A data set is to be transmitted via rvsMVS FTP FTP check routines find error conditions in FTP control output file connection error A data set is to be transmitted via rvsMVS FTP FTP check routines find error conditions in FTP control output file other error A data set is to be transmitted via rvsMVS FTP Send of FTP control file HFILE ended with error A data set is to be transmitted via rvsMVS FTP FTP Server Task Origin data set not found A data set is to be transmitted via rvsMVS FTP FTP Server T
7. In event of an error during transmission of data sets rvs user codes are set by data input output routines or in event of serious errors subtasks of the monitor will terminate with rvs user codes These Codes are indicated by the rvs Monitor They also appear by listing the transmission history by means of program DF078A00 As a rule messages precedes an abnormal condition during a transmission indicating the type of error Code Code decimal hexadecimal Meaning 004 004 Abort because of line error or cancel by operator 008 008 Abend because data cannot be read from input data set or cannot be written to the output data set in most cases the required disk volume cannot be accessed because it is reserved by other jobs Another reason may be the priority of rvs if this priority is too low 012 00C Error during dynamic allocation or a header record has been received containing invalid values 016 010 The requested disk is not mounted or the data set has not been found on the specified volume BTAM 020f 014 An VO error has occurred during reading a data set BTAM The data set has not been found on the specified volume VTAM 024 018 An O Error occurred during writing to a data set BTAM An O Error occurred during writing to or reading from a data set VTAM 028 01C An O Error occurred when a data set is rewound during restart processing 032 020 During restart a block number or record number has been
8. This message is issued by the rvs XOT CTCP task when an abend occurs The message shows the content of the registers 0 to 7 at the time of abend nn REGS 8 15 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX This message is issued by the rvs XOT CTCP task when an abend occurs The message shows the content of the registers 8 to 15 at the time of abend nn SESSION REJECTED FOR STATION sid ISTATUS INACTIVE A request for establishing a session with station sid has been rejected because the stations entry is not released yet ISTATUS can be changed dynamically by the Operator see rvs Operations Manual if neccessary nn COMMAND REJECTED TERMINATION OF rvs XOT CTCP IN PROGRESS This message is issued by the rvs XOT CTCP task when an activate command has been entered but termination of the rvs XOT CTCP task has been already started nn ODETTE TASK HAS BEEN POSTED SESSION This message is issued by the rvs XOT CTCP task when the ODETTE task has been posted for termination This message is issued by the rvs XOT CTCP task when the ODETTE task has been detached after termination nn SPECIFIED PARTNER NUMBER INDEX mm NOT DEFINED 172 rvsMVS Messages and Codes 5 rvs Messages DF9I51E DF9I52I DF9I53P DF9I54P DF9I55P DF9I57P DF9I58E DF9I59E This message is issued by the rvs XOT CTCP task if the operator command A SID Cnn Nmm was entered and the speci
9. gt IND ENTRY FOR LINE IGNORED U The mentioned Line Entry has been ignored because the program profile parameter has not been specified WARNING DIAL NUMBER MISSING gt AUTO DIAL FOR NOT POSSIBLE U Autodial is requested for this station but the dialnumber has not been specified PROCESSING OF STATIONS TABLE FAILED PROGRAM ABNORMALLY ENDED The stations table could not be accessed to Please be sure that the table with DD statement STATIONS may be opened by the rvs monitor 40 rvsMVS Messages and Codes 5 rvs Messages DF2210P DF2211E DF2212E DF2213E DF2214E DF2215E DF2216E DF2217E DF2218E SPECIFIED TCP IP STACK name FOR STATION sid NOT DEFINED The specified TCP IP stackname parameter TCPIPADR for station sid could not be found Either the specified stackname is not valid or the corresponding TCP IP controltask is not defined for this stackname see rvs start parameter TCPSTKID in the CNTL member The specified station is not operational cannot be activated ERROR PPROF MISSING NO DEFAULT gt ENTRY FOR SID IGNORED U The mentioned Station Entry has been ignored because no program profile parameter has been specified ERROR SCNL MISSING NO DEFAULT gt ENTRY FOR SID IGNORED U The mentioned Station Entry has been ignored because no subchannel parameter has been specified ERROR SPROF MISSING NO DEFAULT gt ENTRY FOR SID
10. After reception of a data set from station sid an automatic job start should have been executed The allocation of the job data set containing the JOB member failed dynamic allocation error xxxx info code yyyy see SPL Job Management This message will be followed by DF5802i DF5805I R sid MEMBER member NOT FOUND IN DATA SET dsname After reception of a data set from station sid an automatic job start should have been executed but the member containing the JCL could not be found This message will be followed by DF5802I DF5806I R sid JOB PROTOCOL SUBMITTED BECAUSE OF FAILING JOBSTART After reception of a data set from station sid an automatic job start should have been executed but this jobstart failed As a result of this and specification of rvs start parameter JFP YES another job member JFPJCL of the rvs tables dataset has been submitted in order to notify somebody about the failing automatic jobstart DF5807I R sid WRITING OF EVENT event name TO yyyy WAS NOT SUCCESSFUL RC cc 109 rvsMVS Messages and Codes 5 rvs Messages After reception of a dataset from station sid an event event name was written to the job scheduling subsysten yyyy The action was successful or not successful according to the return code of the executed macro DF5808E R sid JOB PREPARED FOR CANCEL BECAUSE OF FAILED RENAME JNM name number After reception of a dataset from station sid the dataset could not be re
11. The message shows information about a file transfer if the file is Sent or Received the number of records or 1K blocks transmitted so far and the file name nn REGS 0 7 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX This message is issued by the rvs X 25 CTCP task when an abend occurs The message shows the content of the registers 0 to 7 at the time of abend 166 rvsMVS Messages and Codes 5 rvs Messages DF9535I DF9536W DF9537W DF9538P DF9539P DF9540P DF9541P DF9542W nn REGS 8 15 xxxxxxxx XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXK XXXXXXXX XXXXXXXX XXXXXXXX This message is issued by the rvs X 25 CTCP task when an abend occurs The message shows the content of the registers 8 to 15 at the time of abend nn COMMAND REJECT FROM GATE FOR COMMAND CURRENTLY NOT EXECUTABLE This message is issued by the rvs X 25 CTCP task when a VTAM Send request is completed with return code 0404 and sense 081C This indicates that a command sent by the CTCP is temporarily not executable by the GATE function in the IBM NPSI product The reason for command reject is probably that an X 25 Clear packet has been received from the network on the associated virtual circuit It can be a temporary problem that may be solved by stopping the CTCP task using the command P rvsX or even B rvsX and starting it again If this does cases it might be a permanent error Reload of the NCP NPSI will
12. This message is issued by the rvs XOT CTCP task when an invalid command has been entered The invalid command is indicated in the message nn OPTION ALL NOT SUPPORTED FOR COMMAND This message is issued by the rvs XOT CTCP task when the option ALL has been used for a command that does not support the ALL option nn INVALID COMMAND PARAMETER This message is issued by the rvs XOT CTCP task when an invalid parameter for a command was detected nn SPECIFIED XCB NOT FOUND This message is issued by the rvs XOT CTCP task when the Xot Control Block number XCB specified in a command cannot be found 171 rvsMVS Messages and Codes 5 rvs Messages DF9I29I DF9I30I DF9I34I DF9I35I DF9I37W DF9I39P DF9I44P DF9I45P DF9I50E This message is issued by the rvs KOT CTCP task when a command refering to a station is used Either the station could not be found the station was already active for Activate command or the station was not active nn OK This message is issued by the rvs XOT CTCP task in response to a command that has been accepted and executed This message is issued by the rvs XOT CTCP task in response to a Display DS command The message shows the ACB name used by the CTCP task and the name of the Logical Unit used for XOT link communication LV states the last modification date of program DFO95A nn REGS 0 7 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
13. rvsMVS Messages and Codes 5 rvs Messages DF5408E DF5409E For rr the following values are valid 00 OPEN PROCESSING MAY INCLUDE DYNAMIC ALLOCATION 04 INSERT OF A RECORD 16 UPDATE OF A RECORD KEY OF RECORD NOT CHANGED 20 UPDATE OF A RECORD KEY OF RECORD CHANGED 24 DELETE RECORD 28 CLOSE PROCESSING MAY INCLUDE UNALLOCATION 44 SEQUENTIAL READ OF RECORDS USER ABEND 0540 REASON XX DEC OCCURED An error record occurred during access to the rvs control record A MODCB GENCB or SHOWCB macro could not be exexcuted USER ABEND 0550 REASON XX DEC OCCURED An error record occurred during access to the rvs control record A record was found in the control dataset that could not be decompressed Please use program DF 144A to find and delete the incorect record s Messages DF5410E until DF5411P are for possible error detection only They are not in effect for users purpose DF5410E DF5411P DF5U01P DF5U031 DF5U06I DF5U08E DF5U0 9E INVALID RECORD XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX text ID nn RC 00 REC key ORT sid dsn RD readydate RT readytime SD startdate ST starttime This message is generated if the access to the key data set ended with certain return codes The message may appear if errors occur during access to the key data set SAVING OF rvs KEYDATA AND rvs KEYLOG DATA SET REQUIRED This message appears only in conjunction with message DF5KO2W AUTOMATIC CLOSE FOR KEY DA
14. 1017 3F9 This ABEND is coded in the program DF075Cxx If specifying minutes the PARM characters must be numeric 1018 3FA This ABEND is coded in the program DF075Cxx If specifying lines the PARM characters must be numeric 1019 3FB This ABEND is coded in the program DF075Cxx If specifying the list level LVL the PARM characters must be alphanumeric or alphabetic 1022 3FE This ABEND is coded in the program DF022Bxx The number of relay stations exceeds the maximum limit of 66 Check the number of VIA and BACKUP stations specified in the stations table 1050 41A This ABEND is coded in the program DF078Cxx See rvs User Code 1010 1051 41B This ABEND is coded in the program DF078Cxx See rvs User Code 1011 1052 41C This ABEND is coded in the program DF078Cxx See rvs User Code 1012 1053 41D This ABEND is coded in the program DF078Cxx See rvs User Code 1013 1054 41E This ABEND is coded in the program DF078Cxx See rvs User Code 1014 1055 41F This ABEND is coded in the program DF078Cxx See rvs User Code 1015 1056 420 This ABEND is coded in the program DF078Cxx See rvs User Code 1016 1057 421 This ABEND is coded in the program DF078Cxx See rvs User Code 1017 1058 422 This ABEND is coded in the program DF078Cxx See rvs User Code 1018 17 rvsMVS Messages and Codes 3 rvs Abend Codes 1059 1060 1200 1201 1510 1511 1512 1662 1690 1691 1720 1723 1730 423 4
15. 5 rvs Messages rvs message structure All messages of the rvs monitor contain a message code under which they are explained in this manual The message code has the following structure e g DF 30 01 A RVS OC READY je type of message consecutive number routine which generates the message constant DF The following types of messages can occur Action required an error may be present an error is present information message of the remote station message appears only in printout used for display of internal trace data warning additional information NscvZz mo gt Station related messages of the rvs monitor contain a function indicator station name and if applicable the line address of the TP line on which the transmission is taking place e g DF3009I R11 050 READY TO TRANSMIT fine address subchannel of BTAM line station name active function 24 rvsMVS Messages and Codes 5 rvs Messages or DF 99041 A op URI RA SESSION TERMINATED FOR LU lu _ indication of VTAM session station name active function Active functions f are Oa lt lt 0 J the line is activated but no transmission of data is taking place entry to the control data set is inserted processing of operator messages scanning for data sets to be transmitted queued requests This character is also used for all messages which are displayed on the
16. An error occurred during allocation of the trace data set The DYNALLOC macro returned with the code xxxx This code is described in OS VS2 MVS SPL Job Management DFO200I SUBTASK STARTED FOR LU luname CID cid A subtask has been started to terminate the VTAM session LU luname CID cid This may be necessary if the transmitting or receiving program is not able to terminate the session itself e g an ABEND has occurred or the command B sid was entered cuspst DFO201E 4 TERMSESS ISSUED FAILED FOR LU luname RC xx yy FDBK zz lsESSIONC The message describes if the termination of the session to the logical unit represented by luname has been successful or not The meaning of the codes is xx yy register 15 register 0 zz feed back code The codes are described in ACF VTAM Programming DFO301E DEnnnAnn COMPLETION CODE FOUND SYSTEM sss USER uuuu An non correctable error occurred The result is the ABEND of the subtask The codes sss and uuu are described in OS VS Message Library VS2 System Codes and in this Documentation Chapter 3 rvs Abend Codes DFO302I x SNAP DUMP TAKEN ON rvsDUMP An extensive SNAP DUMP is generated when completion codes occur which were previously forced by the command DUMP SCC xxx or DUMP UCC xxxx STARTED DF0401I nn TRACE b FOR X 25 MASTER LU REMOTE STATION sid stoppen 26 rvsMVS Messages and Codes 5 rvs Messages DFO401I DFO402E
17. DATASET NOT UNCATALOGED dsname The temporary data set with timestamp dsname has been renamed to its final name but could not be uncataloged R ORT REMOTE JOB name NOT AUTHORIZED NOT SUBMITTED R ORT EFFECTIVE SPEED BPS R ORT text name R ORT LOG ENTRY LG FOR name Messages DF1244P to DF1249P are for possible error detection only They are not in effect for users purpose RVS VERSION HAS CHANGED UPDATE OF RR ENTRIES STARTING UPDATE OF RR ENTRIES ENDED RC rc RECORDS PROCESSED nnn The above messages are displayed during start of the rvs monitor if the rvs release has changed an update of the rvs loadlibrary with a new rvs version was done and the rvs control data set RVS KD of the old version is used further on 34 rvsMVS Messages and Codes 5 rvs Messages DF1501A DF1504P DF1505P DF1507P DF1508P DF1520P DF1520P DF1551A DF1554P DF1555P DF1558P In this case some flags of elder resident receive entries must be modified in order to keep compatibility with the new version rc denotes the returncode of this function and nnn denotes the number of processed resident receive entries in general the total number of rr entries of the rvs control data set I sid NO SMF RECORD WRITTEN The User SVC for writing SMF records returned with a non zero returncode I sid INVALID START TIME An entry of the control data set relating to a data set which is to be
18. DF9337P DF9338I The module which writes the data records to the output data set terminated with system completion code sss and user completion code uuu The transmission will be cancelled R sid mn REMAOTE BCC rrrr LOCAL BCC 1111 text The number of bytes transmitted in the last line buffer is not equal to the number of bytes in the received in the line buffer R sid mn INVALID FEATURE xxxxxxxx IN H RECORD The remote station indicated in a H record to transmit a data set by using some features At least one of these features is not supported or defined at the local station ENQ USE R sid mn b RETURN CODE xx DSN dsname DEQ HAVE The execution of ENQ and DEQ macros is listed on printout R sid FINAL STATION sid SPECIFIED BUT NO VALID ENTRY IN STATIONS TABLE A data set is to be received from a remote station It is to be transmitted to a third station sid but this station is not defined in the local stations table The receiving of this dataset ist rejected R sid RECEIVING REJECTED BECAUSE OF PARM NORELAIS sid A data set is to be received from a remote station It is to be transmitted to a third station sid but routing to this station is to be suppressed Parameter NORELAIS sid The receiving of this dataset ist rejected R sid mn r RECORD RECEIVED DSN dsname Receiving of a rvs protocol record type r is listed on printout R sid mn r RECORD HAS BEEN SENT The transmission of a rvs prot
19. DFO403E DFO701I DFO702E DFO703E DFO8O1lI DF0802I A X 25 XMLU Trace was started stopped nn states the CTCP number sid shows the connected station STARTED nn TRACE FOR SES nnnnn REMOTE STATION sid STOPPED A trace for an X 25 or LU 6 2 station was started stopped nn states the CTCP number in case of X 25 nnnnn shows the session number nn DYNALLOC ERROR xxxx yyyy FOR TRACE DATASET The message shows the error and info code of allocation of trace data set nn OPEN ERROR FOR TRACE DATASET The trace data set could not be open STARTED SESSION nn TRACE FOR 4 b XXXXX REMOTE STATION XXX lsToPPED SOCKET J A trace for an TCP IP or XOT station was started stopped XXXXX shows the socket session number DYNALLOC ERROR XXXX YYYY FOR TRACE DATASET The message shows the error and info code of allocation of trace data set OPEN ERROR FOR TRACE DATASET The trace data set could not be open BUFNO nn STORAGE aaK UNUSED bbK EXCNT cc The message is displayed as response to the command DS BFPOOL or DS BFPOOL ALL Starting with version 2 2 05 rvs uses an own bufferpool for the OFTP components X 25 LU6 2 and TCP IP This bufferpool shall help to improve performance by reducing system services GETMAIN and FREEMAIN The bufferpool includes buffers which are not longer used but which might be requested at a later time nn denotes the number of unused buffers w
20. IGNORED U The mentioned Station Entry has been ignored because no session profile parameter has been specified ERROR LUNAME MISSING NO DEFAULT gt ENTRY FOR SID IGNORED U The mentioned Station Entry has been ignored because no luname applid parameter has not been specified kkkkkkk USERABEND 1022 RELAIS LIST OVERFLOW kkkkkkkkk The number of relay stations exceeds the maximum limit of 66 stations See also User Abend 1022 ERROR AUTODIAL OR AUTOACT REQUIRED gt ENTRY FOR SID IGNORED U The mentioned Station Entry has been ignored because the AUTODIAL parameter as well as the AUTOACT parameter has been specified Only one of them can be accepted ERROR ERROR IN SEND RECEIVE PASSWORD gt ENTRY FOR SID IGNORED U The mentioned Station Entry has been ignored because the send or receive password is invalid ERROR ODETTE ID MISSING gt ENTRY FOR SID IGNORED U The mentioned Station Entry has been ignored because no ODETTE identification has been specified 41 rvsMVS Messages and Codes 5 rvs Messages DF2219E DF2220I DF22251I DF222CI DF22251I DF2226W DF2227E DF2228W DF2229W DF2230W DF2231E ERROR X 25 NUMBER MISSING gt ENTRY FOR SID IGNORED U The mentioned Station Entry has been ignored because no ODETTE identification has been specified TOTAL NUMBER OF INTERNAL STATION TABLE ENTRIES The number of inte
21. Trailer File Id TFID protocol unit The following list describes the different reason codes 01 Invalid filename 02 Invalid destination 03 Invalid origin 04 Storage record format not supported 05 Maximum record length not supported 06 File size is too big 10 Invalid record count 11 Invalid byte count 12 Access method failure 13 Duplicate file 99 Unspecified reason DF8890I D sid sesid FILE DSORG NOT PS gt SEND REQUEST NOT ACCEPTED The FTP Client Task issues this message when send file has PDS organisation RVS MVS FTP not support PDS files DF8898P D sid sesid KDUPDAT 88F xxxxxxxx TYP xx The FTP Client Task issues this message List internal action of FTP Driver task with KD control file For internal use only 136 rvsMVS Messages and Codes 5 rvs Messages DF8899P DF88A0P DF88A1P DF88A2P DF88A3P DF88A4P DF88A5P DF88A6P DF88A7P DF88A8P DF88A9P DF88BOP DF88B1P DF88B2P DF88B8P DF88B3P DF88B4P DF88B5P DF88B6P DF88B7P DF88BAP DF88V1W DF88V1W DF88V1E DF88V2W DF88V3W DF88V4E D sid sesid xxxxxxxx nnnnnn nnnnnn The FTP Client Task issues this message routine Shows is the name of FTP Client Task subroutine that gets control For internal use only D sid sesid CS RECORD FOUND DSN dsname D sid sesid NO CS RECORD FOUND DSN dsname D sid sesid ORIGIN STATION KNOWN D sid sesid SENT DSN dsn
22. and access method acme has ended S sid acme nm POINTER TO KDRECORD AREA NOT AVAILABLE This message indicates that the process of selecting a send request for transmission cannot be continued because the session for the transmission is not ready e g session termination because of line problems The transmission will be restarted automatically when a new session to the remote station sid has been established S sid acme nm sSsid name a DISPATCHER POSTED TASK POSTCODE 4 b DISPATCHER POSTED TASK POSTCODE 8 c This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP Message a is displayed during selection of next send request and show kdrecord contents KDrecords are show in sequence in internal KD dataset s may be A for active entry U for used entry transmission in progress D for completed entry transmission is finish Message b is displayed during DEQ processing and show that DEQ request ended with return code 0 90 rvsMVS Messages and Codes 5 rvs Messages DF5237P DF5238P DF5239P DF5243P DF5245P DF5246P DF5248P Message c is displayed during DEQ processing and show that DEQ request ended with return code not 0 Report this message to system programmer S sid acme nm CURRENT SCT ENTRY NOT ASSIGNED WITH AN ACTIVE SESSION This message indicates that a send request is to be assigned released
23. error occurred State and info code values are described in message DF94031 Z sid accm sessonid INVALID FPDU RECVD STATE nn IC mm This message is issued by the Odette File Transfer Protocol task when a received protocol unit contains invalid data The state and information code values indicate in which situation the error occurred State and info code values are described in message DF94031 F sid accm sessonid SESSION TERMINATION STARTED This message is issued by the Odette File Transfer Protocol task when session termination starts in response to an operator cancel command F sid accm sessonid UNKNOWN STATION ID INV PASSWORD odette code rc This message is issued by the Odette File Transfer Protocol task when a Start Session Id SSID protocol unit has been received and either the connecting station is unknown or an invalid password was received In the message is shown the connecting station code and a reason code which is 03 unknown station or 04 invalid password F sid accm sessonid ATTRIBUTE MISMATCH FOR STATION ID odette code This message is issued by the Odette File Transfer Protocol task when Start Session Id SSID protocol units has been exchanged and the stations attributes have been merged During the merge process it was found that the station attributes prevented a session continuation The message shows the Odette code for the partner station Z sid accm sessonid END OF SESSION ESID CODE 2 222 222
24. from the indicated partner LU The LOSS request is received when the last session for the indicated mode nmae is terminated Also shown is whether the request was accepted or rejected A request is rejected if no station can be found for the parter mode combination This message is issued by the rvs APPC task manager routine A FMH5 request was received from the indicated partner LU The FMH5 request is received when a new conversation is requested from a partner Also shown is whether the request was accepted or rejected A request is rejected if no station can be found for the parter mode combination SENSE xxxx This message is issued by the rvs APPC task manager routine A VTAM APPCCMD DEFINE request was issued to define the session limits to a partner node but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information SPECIFIED STATION 2222222222222 This message is issued by the rvs APPC task when a command refering to a station is used Either the station could not be found the station was already active for Activate command or the station was not active OK This message is issued by the rvs APPC task in response to a command that has been accepted and executed SESSION LIMIT nnn REACHED FOR STATION 178 rvsMVS Messages and Codes 5 rvs Messages This message is issued by the rvs APPC task in response to an
25. jjj XXXX yyyy really refresh time value of DSPTI parameter value of DSPTIW parameter standard value 5 sec number of entries in internal KD dataset of Dispatcher number of entries in external KD dataset of Dispatcher END OF SEND REQUESTS SELECTION xxxx aaaa bbbb cccc zzz The dispatcher subtask ended dispatching cycle DSPTI value From xxxx number of entries in internal KD dataset aaaa bbbb cccc zzz D 1 2 L x number of entries that were completed during dispatching time number of entries that were in use transmission in progress number of entries that were free active Dispatcher trace active flag T DISP active flag T DISP1 active flag T DISP2 active flag T DISPL for LU6 2 component active flag T DISPX for X 25 component DD sid name status reason This message is a response for the command DD sid which displays a list of all send requests for the remote station sid name denotes the name of the dataset to be sent up to 26 chars Field status shows information about the status of the send request the following self explaining values may be displayed READY FOR TRANSMISSION TRANSMISSION IN PROGRESS TRANSMISSION COMPLETE OR ABENDED NOT READY reason For status NOT READY an additional self explaining information about the reason is displayed DD sid QDyyddd OThhmmss ccppx sSsid name a DD sid kkkkk kkkkkkkk2 k END OF INTERNAL KD
26. message shows the SETLOGON type START STOP and the VTAM return code The rvs APPC task will terminate if SETLOGON START is not successful DF9711E ACB CANNOT BE USED FOR APPC COMMUNICATION RC RCPRI SEC xxxx xxxx xxxx This message is issued by the rvs APPC task when open of the ACB has completed and the ACB is checked for supported VTAM options The ACB check routine found that the VTAM APPC support could not be used In this message the VTAM return code and the primary and secondary return codes from an APPC verb are shown Update the corresponding APPL statement in VTAM and include the keyword APPC YES before activating the rvs APPC task again DF9712I LOGON REJECT FOR LU REASON This message is issued by the rvs APPC task logon exit routine A logon request was received but the request was rejected The reject reason is shown in the message Also indicated is the name of the Logical Unit LU that was rejected DF9713E F sid ACTSESS FAILED FOR RC xxxx SENSE xxxx This message is issued by the rvs APPC task manager routine A VTAM APPCCMD ACTSESS was issued to accept a new session with the partner sid indicated in the message but the request failed In the message the VTAM return code and sense codes for the failing request are shown Refer to VTAM programming manual for further information DF9714I F sid SESSION ACCEPT FOR LU MODE 7 This message is issued by the rvs APPC task m
27. on line Ill will be initiated in the next time see DIAL command within rvsMVS Operations Manual for more details DIALNUMBER MISSING FOR STATION sid The command DIAL sid has been entered But the definition of the station sid within the rvs stations table does not include the DIALNUM parameter which is mandatory for autodial The dial request will be ignored LINE 111 NOT DEFINED FOR STATION sid The command DIAL sid III has been entered But there is no entry for station sid within the rvs stations table which includes the subchannel number Ill The dial request will be ignored LINE 111 IS NOT AN AUTODIAL LINE The command DIAL sid IIl has been entered But line Ill is not defined as an autodial line within the rvs stations table The dial request will be ignored DSN PARAMETER INVALID OR MISSING COMMAND IGNORED The command FREE DSN dsn been entered But either the required parameter DSN dsn is missing or was not specified correctly The command will be ignored DATASET dsn UNALLOCATED The command FREE DSN dsn been entered The dataset dsn has been unallocated successfully from the address space of the rvs monitor DATASET dsn NOT ALLOCATED TO rvs The command FREE DSN dsn been entered But the dataset dsn is not allocated to rvs No further action is done UNALLOCATION OF dsn FAILED ERROR xxxx yyyy HEX The command FREE DSN dsn been entered The dataset dsn is allocated to rvs But the
28. or the stack number TCP IP assigned with the terminated subtask If the end of the subtask 52 rvsMVS Messages and Codes 5 rvs Messages DF30231 DF30241I DF3025I DF3026I DF3027E DF3028I DF3029E was not normally either a system completion code sss has occurred or the subtask has been terminated with one of the following user return codes uu 00 normal end 04 error during CLOSE of the VTAM X25 RMOP ACB 08 error during OPEN of the VTAM X25 RMOP ACB 12 error during SETLOGON processing 16 rvs Session Table missing In all cases of a nonzero returncode additional error information is displayed before this message appears DISPATCHER SUBTASK ENDED SYSTEM sss USER uuuu The message indicates termination the dispatcher subtask for one of the following reasons e the command P rvs has been entered stop of monitor e the command P DSP has been entered stop of dispatcher e an error system completion code sss hex or user completion code uuuu dec has occurred within the dispatcher routine ROUTING CODE WILL BE CHANGED TO xx This message is issued as a reply to command ROUT xx All following rvs messages will be issued with routing code xx This message is issued during rvs start when specifying another routing code than 08 in parm entry V sid nnn AVERAGE SPEED IS nnnn BITS s This message is issued as a reply to command DV or V sid and indicates the cumulative tra
29. specified length is not positive the session will be terminated as a result of this error which should not occur NO ACTIVE SCT ENTRY FOUND TCB FOR SOCKET CLEARED This message is issued by the rvs TCP IP task when an tcb has been found and no appropriate sct entry exists ACTIVE ODETTE TASK HAS BEEN DETACHED S SID This message is issued by the rvs TCP IP task when an active OFTP task has been detached 118 rvsMVS Messages and Codes 5 rvs Messages DF8319P DF8320E DF8321P DF8322P DF8323W DF8324P DF8325W DF8326E DF8327P DF8328I1 ODETTE TASK NOT RESPONDING WILL BE CANCELLED S SID This message is issued by the rvs TCP IP task when the ODETTE task is not responging any more It will be detached MAX LENGTH FOR READ EXCEEDED REDUCED TO 32767 This message is issued by the rvs TCP IP task when a read macro is to be issued The length of the expected data as indicated in the 4 byte header field exceeds the maximum value of 32767 It will be reduced to this max value SEND ISSUED S L DATA 444444 This message is issued by the rvs TCP IP after a write macro has been issued The message displays the remote station socket number datalength and the first 4 bytes of the sent data ODETTE TASK EOT ECB POSTED SOCKET SID This message is issued by the rvs TCP IP task when the ODETTE task EOT ECB has been posted SEND DATA FLU
30. 12 R sid RECEIVING OF dsname REJECTED DUPLICATE FILE See message DF3738E r sid FOR FIXED RECORD FORMAT BLOCK SIZE MUST BE IDENTICAL WITH RECORD LENGTH This message mainly refers to reception from a DOS station Fixed record format has been chosen but the block size is inconsistent with the record length R sid mn DATASET dsname IS NOW BEING RETRIEVED FROM MIGRATION See DF3740I R sid mn DATASET dsname COULD NOT BE RETRIEVED FROM MIGRATION See DF3741E S sid mn DSN dsname VOL volume STARTING The transmission of the data set dsname is starting If the transmission is a restart the message is extended by RESTARTS AT RECORD nnn an information about the restart count The message is kept on the screen until the first data bytes have been transmitted 67 rvsMVS Messages and Codes 5 rvs Messages DF3603E DF3604A DF3605E DF3606E DF3607E DF3609E DF3610E DF3611E DF3613W S sid mn RESTART COUNT EXCEEDS TOTAL AMOUNT OF RECORDS IN THE DATA SET The data set consists of less records than the restart count specified by the receiving station Any restart is impossible the send request is set into the HOLD status S sid mn DATA SET NOT FOUND ON SPECIFIED VOLUME The data set to be transmitted see DF36011 is not located on the specified volume S sid mn VOLUME volume IS NOT MOUNTED Access to the data set to be transmitted is not possible because the required volume is not
31. 660 661 740 745 746 750 760 762 763 764 280 285 286 28A 294 295 2E4 2E9 2EA 2EE 2F8 2FA 2FB 2FC send request record must be updated but an error occurred in this situation An error occurred during access to the rvs Key Data Set A MODCB GENCB or SHOWCB macro could not be executed or the control data set could not be opened This abend may occur if a new Key Data Set has been created but not initialized This ABEND is coded in the program DFO54Kxx The rvsKEYLOG Data Set is full This ABEND is coded in the program DF054Kxx The installation exit DFUX001 ended with a nonzero return code This ABEND is coded in the program DF054Kxx An error occurred during access to the rvs control record A record was found in the control data set that could not be de compressed This ABEND is coded in the program DFO66Bxx An error occurred during allocating the rvs control data set or the partitioned data set containing the member stations table This ABEND is coded in the program DFO66Bxx Should not occur error An error occurred during access to the rvs User Data Set A MODCB GENCB or SHOWCB macro could not be executed or the user data set could not be opened This abend may occur if a new User Data Set has been created but not initialized If this abend occurs within the ISPF panels of rvs the reason may be insufficient access authority for the rvs user data set require
32. Activate station command The command cannot be honored as no more sessions are allowed to the station DF9731I ACTIVATION REJECTED FOR MODE CLOSED This message is issued by the rvs APPC task in response to an Activate station command The command cannot be honored as the partner station has closed the mode used for sessions DF9732I ACTIVATION REJECTED FOR BUSY This message is issued by the rvs APPC task in response to an Activate station command The command cannot be honored as session negotiation is being done for the station DF9733E ERROR DURING VTAM RPL PROCESSING This message is issued by the rvs APPC task manager routine A VTAM APPCCMD request has been issued but during completion of the request a logical error occurred The RPL used for the request is not usable and the RPL will be skipped This message should never occur DF9734E APPCCMD RCVFMH5 FAILED FOR 22 RC xxxx SENSE xxxx This message is issued by the rvs APPC task manager routine The APPCCMD RCVFMH5 was issued to read a received function management header type 5 but the request failed The FM Header type 5 represents an allocation request from a network partner In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information DF9735E APPCCMD RECEIVE FAILED FOR RC xxxx SENSE XXxx This message is issued by the rvs APPC task manager routine
33. After entry of the command T sid this message appears and signifies that a trace has been started for line nnn and station sid A sid nnn TRACE ALREADY ACTIVATED The command T sid has been entered although a trace is already running for sid and the line nnn O sid nnn TRACE NOT ACTIVE The command O sid has been entered although no trace is still active on line nnn for sid O sid nnn TRACE STOPPED The trace for sid on line nnn was stopped by the command O sid lt k rvs OC A sid nnn IS PENDING The message is the same like DF3001A but the process of activating the line control task for sid nnn is not yet complete Reason The line control module cannot be loaded from the rvs load library the line control module is the first program of the used program profile may be listed via X sid P The disk volume on which the rvs load library resides cannot be accessed may be the disk volume is reserved by another job Action Wait until this disk volume can be accessed or 1 Stop the line control P sid nnn 2 Make sure that the rvs load library may be accessed 3 Activate the line control A sid nnn A sid nnn REJECTED TRY LATER Activating of line control for sid or sid nnn has been rejected because a previous activating for this station or line is not yet complete Message DF3036l indicates the previous activating x ALL y COMPLETE 54 rvsMVS Messa
34. But the rvs VTAM subtask cannot be started without session table Either member SESSIONS of the rvs Tables Dataset see Installations Manual is empty or does not exist or the DD name SESSIONS within the rvs start procedure is assigned to another empty dummy file As a result of this the rs VTAM subtask cannot be started support of SNA sessions by rvs is impossible unless the rvs Sessions Table is correctly created and assigned to the rvs start procedure stop DF9028I VTAM SUBTASK OF rvs WILL CLOSE BECAUSE OF VTAM QUICK STOP CANCEL J CONTINUE CURRENT TRANSMISSION WILL BE CANCELLED BE BROKEN J The operator stopped VTAM by entering a HALT NET command or VTAM stopps because of an error or the operator has entered a VARY NET INACT command for the VTAM application rvs In case of a normal stop all transmissions will be completed in case of a quick stop the transmissions will be terminated If the command HALT NET CANCEL has been entered the rvs VTAM control task will be stopped at once action like the rvs command B rvsVTAM DF9028A ENTER A rvsV AFTER RESTART OF VTAM After VTAM has been started again or after entering VARY NET ACT for application rvs the connection to VTAM can be reestablished by entering A rvsVTAM DF9029E A sid mn SUBTASK DID NOT START WILL BE DETACHED For explanation see message DF9023E The only diffrerence is that the remote station tried to establish a session DF9030I F si
35. DF3400I is not located on the specified volume A system completion code of 213 is written into the assigned control data set entry The status of the entry changed from the active to the hold status So an automatic start or restart is prevented Causes can be e Incorrect data set name or incorrect volume number was specified during queuing for transmission e The data set has been deleted in the meantime 62 rvsMVS Messages and Codes 5 rvs Messages DF3415A S sid VOLUME volume IS NOT MOUNTED Access to the data set to be transmitted is not possible because the required disk is not mounted not online DF3416P S sid SPACE nnnnn mmmmm TRKS During start to transmit a data set to sid the occupied disk space is listed nnnnn Number of occupied tracks mmmmm Number of occupied tracks in 3330 units DF3417E S sid DYNAMIC ALLOCATION ERROR xxxx An error has occurred during data set allocation For error code xxxx see IBM brochure OS VS2 MVS System Programming Library Job Management DF3419W S sid DATA SET EXCEEDS ONE 3330 VOLUME COMPRESS REQUIRED The data set to be transmitted exceeds the capacity of a 3330 disk The data set can be compressed in advance by means of program DF081A00 see rvsMVS User s Manual The data set is transmitted anyway This is only a warning message No action required DF3420W S sid BLOCKSIZE EXCEEDS ONE 3330 TRAK The block size of the data set to be transmitted exceed
36. EEIDORIG odette id of sender of EEID D sid sesid EEIDDEST odette id of recipient of EEID D sid sesid EEIDDATE date EEIDTIME time These messages are issued by the FTP Server task when an error concerning a received end to end response has occurred They are intentionally issued for error detection For internal use only KDRECTYP KDREMOTE KDNEXT KDSTATUS nn KDDSN dsn name KDREADYD nnnnnnn KDREADYT nnnnnnn KDSTARTD nnnnnnn KDSTARTT nnnnnnn KDREC kdrecord D sid sesid D sid sesid D sid sesid D sid sesid D sid sesid HF D sid sesid D sid sesid D sid sesid D sid sesid D sid sesid KEY KDRECTYP KDREMOTE KDNEXT KDSTATUS nn KEY KDDSN dsn name KEY KDREADYD nnnnnnn KDREADYT nnnnnnn KEY KDSTARTD nnnnnnn KDSTARTT nnnnnnn KEY KDREC kdrecord The FTP Server task issues these messages Show contents of KD file Record For internal use only D sid sesid DSN dsn The FTP Server Task during verification MVS SMS parameters issues this message Shown is the real FTP file name D sid sesid DSORG dsorg STCL stcl MGCL mgcl DACL dacl The FTP Server Task during verification MVS SMS parameters issues this message Show the SMS parameters of real FTP file name D sid sesid NON SMS MANAGED DATAFILE The FTP Server Task during verification MVS SMS parameters issues this message Real FTP file is not SMS managed D sid sesid SMS DYNALLOC ERROR
37. F sid R RECORD dsname OUTSIDE PROTOCOL BOUNDARY IGNORED A invalid R Record has been arrived Because of no transmission before this record will be ignored DF56461I F sid R RECORD XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX A invalid R Record has been arrived This record has a wrong length or incorrect fields COUNTER or DSN Line Control Program DF057B00 Look for non descripted messages to DF56xxx DF5703E F sid 111 INVALID SEQUENCE OF PROTOCOL RECORDS A line connection to station sid has been established using line Ill During transmission sending or receiving of a dataset rvs detected an invalid flow of protocol records As a result of this error the line connection will be broken The reason for this error may be e the remote station does not handle the used transmission protocol in a correct way e the transmission protocol which is defined to be used for the remote station sid see member PROGPROF in the rvs tables dataset described in the rvs interface description is not correct This means the transmission protocol defined for station sid does not meet the protocol specifications which the remote station is able to process If this is a permanent error a rvs trace should be started in order to obtain more detailed information about the flow of protocol records This information should be routed to the distributor DF5705W F sid 111 INVALID RECORD TYPE X tt RECEIVED RECORD IGNORED A line connection
38. FILE b DD sid kkkakkKKKKKKKS k END OF EXTERNAL KD FILE c DD sid kxkxkkk zkkkkkkkk KKKKKK INTERNAL KD EMPTY d 87 rvsMVS Messages and Codes 5 rvs Messages DD sid kkkkkkokkkkkkkkm kkkkkk EXTERNAL KD EMPTY e DD sid kkkk kkkkkkkk kkkkkk BAD DD COMMAND DD sid x k kkkk kkkkkkkk KKKKKK SID NOT FOUND g DD sid kkkkk kkkkkkkk kkk SID FOUND SYNTAX ERROR h DD sid kkkkkk kkkkkkkk kkk INCORRECT FILE NAME i DD Sid kkk kkKKKKKES ke INT KD NO ENTRY FOUND j DD sid tkkkkkk kkkkkkkk x kk EXT KD NO ENTRY FOUND k This message one or more is a reply for DD command for DD sid or DD command for DD ACT command for DD ALL command day of queuing dataset time of queuing dataset day of starting dataset time of starting dataset cc may be external KD dataset only DD sid E command sid may be sid name ACT ALL QDyyddd QThhmmss SDyydda SThhmmss E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB or pp x NS s may be A U D Message b Message c Message d Message e Message f early time amp date station not found station not active access method not active same name tape disk conversion program running send request in hold state line already active BSC serialisation of datasets final st
39. In general several of these messages with different self explaining text will be printed immediately one behind the other complete sysprint protocol of the load utility DF6110E R sid mn ALLOCATION ERROR XXXX YYYY dataset A dataset has been received from station sid The received dataset is an unloaded PDS which has been loaded successfully An unallocation error has occurred for dataset which may be either UNLOADED PDS or PDS for the error code xxxx and the info code yyyy see for example the IBM manual OS VS2 SPL Job Management The transmission will be completed normally mn denotes the session SNA or the line address BSC which was used for receiption of this file DF6111E R sid mn UNLOADED PDS NOT SCRATCHED RC xx SC yy A dataset has been received from station sid The received dataset is an unloaded PDS which has been loaded successfully After this the unloaded PDS used as a work dataset is no longer needed and should be scratched but scratch of this dataset failed xx denotes the returncode yy denotes the scratch code of the scratch macro see for example the IBM 113 rvsMVS Messages and Codes 5 rvs Messages DF6112E DF6115P DF6201I DF62021I DF6203I DF6204I DF62051I DF6206I DF6207E manual OS VS2 SPL Data Management The transmission will be completed normally mn denotes the session SNA or the line address BSC which was used for receiption of this fi
40. Messages Messages of the SNA LU 6 0 Session Handler task DF9900I R sid mn SUBTASK STARTED FOR LU lu INIT xx The receive module has been started to support session mn to station sid logical unit lu xx 40 by OPENSEQ after receiving a bind request 80 by OPENDST AQUIRE after entering A sid AO by SIMLOGON CO by OPENDST ACCEPT after receiving a logon request DF9901E R sid mn INVALID SESSION INITIALIZATION PARAMETER The calling program passed an invalid initialization module to the receive module see message df9900l SESSION ESTABLISHED FOR LU lu CID cid DF9902I R sid mn SDT REC SESSION OK loPENSEC OK J The session mn to the logical unit lu with ClD cid has been established In case of a primary logical unit this message occures two times e the first time with the text OPENSEC OK session established but no data traffic is possible at this time e the second time with the text SDT REC SESSION OK now data may be exchanged This message is also displayed if a clear command has been received DF9903E R sid mn LU lu macro FAILED RTCD xx yy FDBK2 zz REQ rr SS ssss US uuuu ADR aaaa The VTAM macro macro for supporting the logical unit lu ended with failure For a description of the codes xx register 15 yy register 0 zz feedback code rr request code ssss system sense code UUUU user sense code see the related section in this manual aaaa specifies t
41. ODATE QTIME S ORT ACCM SESSID CANCEL REQUEST WAIT FOR LINE DRIVER TIMER S ORT ACCM SESSID CANCEL REQUEST WAIT FOR DISPATCHER TASK LINE DRIVER Z ORT ACCM SESSID CANCEL REQUEST WAIT FOR LINE DRIVER TIMER CLOSE REQUEST WAIT FOR LINE DRIVER TIMER INVALID DATA S ORT ACCM SESSID CANCEL REQUEST WAIT FOR DISPATCHER TASK LINE DRIVER S ORT ACCM SESSID CANCEL REQUEST WAIT FOR LINE DRIVER DISPATCHER TIMER STOP REQUEST WAIT FOR LINE DRIVER DISPATCHER TIMER CLOSE REQUEST WAIT FOR LINE DRIVER DISPATCHER TIMER INV DATA S ORT ACCM SESSID CANCEL REQUEST WAIT FOR LINE DRIVER EMPTY QUEUE TIMER CLOSE REQUEST WAIT FOR LINE DRIVER EMPTY QUEUE TIMER INV DATA Z ORT ACCM SESSID CANCEL REQUESTED BY LINE DRIVER Messages DF9490P until DF9499P are for error detection only They are not in effect for users purpose 162 rvsMVS Messages and Codes 5 rvs Messages Messages of the X 25 Control Task DF9501I DF9502P DF9503E DF9504I DF9505E DF9506E DF9507E DF9508P This message is issued by the rvs X 25 CTCP task when task initialization is complete nn states the CTCP number LV denotes to the current program version of program DF095A This message is issued by the rvs X 25 CTCP task when task termination has started or is complete nn rvs X 25 CTCP ABEND CODE EP PSW This message is issued by the rvs X 25 CTCP task when an abend occu
42. RC nnnnnnn ERRCD nnnnnnnn 129 rvsMVS Messages and Codes 5 rvs Messages The FTP Server Task during verification MVS SMS parameters issues this message Dynamic allocation during checking SMS parameters real FTP file ended with error DF85BEP D sid sesid MOVE FILE sms parm ALLOCOLD old KDRECNEW new The FTP Server Task issues this message during verification rvsMVS SMS parameters SMS parameter of real FTP file and rvsMVS SMS parameters are different The content of real FTP file is moved to new file with rvsMVS SMS parameters rvsMVS Messages and Codes 5 rvs Messages Messages of the FTP Polling Task DF8600I DF8607P DF8613P DF8617P DF8701I DF87021I DF8703E DF8704I DF8705I STARTED FTP POLLING TASK b VERSION vvv STOPPED dd mm yy tt mm aa bb cc Start or stop message of FTP Polling Task This program is started direct after start of the FTP Main Task vvv specify version of FTP Polling Task dd mm yy tt mm time of assembly aa bb cc time of last changes in the FTP Polling Task RVSMVS FTP FILES FOUND The FTP Polling Task issues this message when FTP control file s is are found List of FTP control file s following in the message s DF8613P A file name volser The FTP Polling Task issues this message when FTP control file s is are found The message contains dsn of FTP control file and volser RVSMVS FTP NO SEARCH FLAG FTPFLGHD ON
43. The FTP Polling Task issues this message when FTPPOLTI time interval is elapsed but not all files from last polling search are serviced This message is issued by the rvs APPC driver task when task initialization is complete for the partner station sid This message is issued by the rvs APPC driver task when task termination is complete for the partner station sid APPC DRIVER ABEND CODE EP PSW This message is issued by the rvs APPC driver task when an abend occurs The message shows the system abend code the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done after all subtasks has been terminated REGS 0 7 MXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX This message is issued by the rvs APPC driver task when an abend occurs The message shows the content of the registers 0 to 7 at the time of abend REGS 8 15 xxxxxxxxK XXXXXXXX XXXXXXXX XXXXXXXX 131 rvsMVS Messages and Codes 5 rvs Messages DF8706I DF8707I DF8708E DF8709E DF8710E DF8711E DF8712E DF8713E XXXXXXXX KXXXXXXXX XXXXXXXX XXXXXXXX This message is issued by the rvs APPC driver task when an abend occurs The message shows the content of the registers 8 to 15 at the time of abend This message is issued by the rvs APPC driver task routine when a VTAM request for APPC LU 6 2 is done The message shows the APPC command and qualifier
44. The message shows information about a file transfer if the file is Sent or Received the number of records or 1K blocks transmitted so far and the file name 157 rvsMVS Messages and Codes 5 rvs Messages DF94321I DF9433P DF9434I DF9435I DF94352 DF9437P DF9438I DF9439I DF9440I DF9441T This message is issued by the Odette File Transfer Protocol Task in response to a Display Velocity DV command The message shows the average transmission speed for the time the transmission started up to now Z sid accm sessonid CURRENT COUNTERS RCNT H HHH UCNT HH HHHHHH This message is issued by the Odette File Transfer Protocol Task additionally to message DF9409I in case of EFNA to print the current values of record count and unitcount sender own This message is issued by the Odette File Transfer Protocol Task if the volume containing the file is not mounted This message is issued by the Odette File Transfer Protocol Task if the file is not found on the volume specified in the KDRECORD Shown is the virtual file name A sid PHYSICAL DSN VOLUME This message is issued by the Odette File Transfer Protocol Task if the file is not found on the volume specified in the KDRECORD Additional this message shows the physical datasetname of the file Z ORT ACCM SESSONID VALUES C0 C1 227272222 22222272 R4 7 27272227272 222272722 777777727 77777777 This me
45. This message is issued by the rvs TCP IP task when an active OFTP task has been detached ODETTE TASK NOT RESPONDING WILL BE CANCELLED S SID This message is issued by the rvs TCP IP task when the ODETTE task is not responging any more It will be detached MAX LENGTH FOR READ EXCEEDED REDUCED TO 32767 This message is issued by the rvs TCP IP task when a read macro is to be issued The length of the expected data as indicated in the 4 byte header field exceeds the maximum value of 32767 It will be reduced to this max value SEND ISSUED S L DATA 444444 This message is issued by the rvs TCP IP after a write macro has been issued The message displays the remote station socket number datalength and the first 4 bytes of the sent data ODETTE TASK EOT ECB POSTED SOCKET SID This message is issued by the rvs TCP IP task when the ODETTE task EOT ECB has been posted SEND DATA FLUSHED DUE TO LOCKED SERVER QUEUE s This message is issued by the rvs TCP IP task when data to be sent to the ODETTE file transfer protocol task was rejected due to a locked server queue ie The task was not ready to accept the request The message displays the related socket number This message is issued by the rvs TCP IP task when a connection is to be initiated This message displays IP address and port number of the remote station and of the own station as well 123 rvsMVS Messages and Co
46. VTAM session This message is a response to the commands DS or sid text can be substituted by NO ACTIVE SESSION the subtask is started but there is no VTAM session established SESSION BEING ESTABLISHED The subtask just tries to establish a session SESSION ACTIVE This is an active session on which no data sets are transmitted operator communication session WAITING FOR WORK The session is established but at this time there is no data transfer dsname nnn RE VOL volume status For a running transmission the following is listed dsname data set name nnn number of transmitted records volume volume number status status of this transmission DF3016A NO SPACE IN LOG DATA SET SAVING OF KD AND LOG REQUIRED The LOG data set is completely filled There will be done no more updates of the control data set This message is followed by User Abend 3003 decimal abend of the rvs monitor Before the rvs monitor is started again the execution of procedure PDF0014A is required vram DF3017I x25 SUBTASK status 51 rvsMVS Messages and Codes 5 rvs Messages DF3018I DF3019I DF3020I DF3021I DF3022I LRMOP This message occurs if one of the VTAM X25 specific rvs commands has been entered and the required action could not be executed The status may be NOT ACTIVE The rvs VTAM X25 RMOP control module is not active It may be started by entering the command A rvs
47. WARNING GZIP COMPRESSION NOT INCLUDED IN CURRENT LICENCE KEY IGNORED FOR SID XXX The GZIP compression parameter COMPRESS GZIP found in station entry for SID xxx but the GZIP compression is not included in current licence key The parameter is ignored WARNING EXTERNAL SECURITY NOT INCLUDED IN CURRENT LICENCE KEY IGNORED FOR SID XXX The external security parameter SECURITY EXT found in station entry for SID xxx but the external security is not included in current licence key The parameter is ignored WARNING EXTERNAL SECURITY ONLY SUPPORTED FOR ACESS METHODS X25 LU62 TCP IGNORED FOR SID XXX The external security parameter SECURITY EXT found in station entry for SID xxx but the external security is available only for access method X25 LU62 and TCPIP The parameter is ignored WARNING SECURITY EXT AND COMPRESS YES OFTP FOUND OFTP COMPRESSION DISABLED The external security parameter and parameter COMPRESS YES OFTP found in station entry This combination is not accepted The Parameter COMPRESS is disabled COMPRESS NO 43 rvsMVS Messages and Codes 5 rvs Messages DF2243W DF2244W DF2244W DF2246W DF2247W DF2248W DF2249W DF2250W DF2251W DF2260W WARNING USER STATIONS NOT INCLUDED IN CURRENT LICENCE KEY IGNORED FOR SID XXX The user station parameter USR YES found in station entry for SID xxx but the user station is not included in current licence key The parameter is ig
48. command for line III has been entered During initialization of the line control program the open processing for the line failed After this message the linecontrol will terminate with user code 20 dec DF5503A A 111 111 READY TO TRANSMIT An activation command for the switched BSC line Ill has been entered This message indicates that activation of the line has completed successfully This is the status where the line control program is waiting for start of data traffic on the line DF5504E f sid 111 INVALID STATION ID RECEIVED A line connection das been established dialing During execution of the identification phase the remote station has sent an identification which is not defined within the rvs stations table As a result of this error the line connection will be broken The rvs trace see chapter 8 may be used to determine the reason for this DF5505E f sid 111 LINE CONNECTED This message indicates that a lineconnection with the remote station sid on line Ill has been established and that the identification phase has been completed successfully DF5506I f sid 111 TRANSMISSION ENDED The transmission s with the corresponding station sid on line Ill has ended After display of this message the line error block LERB is will be displayed and e the line control program will stop if a stop command has been entered for this line previously or e the line control program is waiting for
49. detected nn OFTP TASK ABEND SID DSN 2 2 2222222222 22222222222 This message is issued by the rvs X 25 CTCP task when the ODETTE task EOT ECB has been posted DFXNST ENTERED DFXLOST ENTERED signified call NSEXIT LOSTERM VTAM Exit Routine LOSTERM A session with an LU has been temporarily interrupted or permanently lost the LU or VTAM operator requested that the session be terminated or an event occurred that can affect future operation of the session NSEXIT A network services request unit has arrived for the application program indicating for example that Asession with an LU has been terminated because of a disruption of the path used by the session A session establishment procedure has completed or failed See Comm Server SNA Programming SC31 8829 01 rvsMVS Messages and Codes 5 rvs Messages DF9598W DF9599P DF9599P nn FAILED FOR LU RO R15 This message is issued by the rvs X 25 CTCP task when a VTAM request fails The message shows the failing request the logical unit that issues the request und register RO und R15 nn xxxxxxxx The X25 Task issues this message This message is issued if internal trace modul is used see command T RVSX The name of X25 Task subroutine that gets control is shown This message is for internal use only nn 2222222 VCB CONID SESSION SID The X25 Task issues this message This mess
50. displayed DF4105I f sid mn SYSOUT a FORM bbbb DEST cccccc COPIES dd This message appears as a reply to the command DR in connection with the message DF4101 in case of the received data set has to be printed These parameters are either specifications of the remote station or the content of a resident receive record They are 76 rvsMVS Messages and Codes 5 rvs Messages copied to the job control statements of a job which is automaticaly started after the receiption of the data set The meaning of the parameters is a SYSOUT class bbbb SYSOUT formular number cccccc distination name of a RJE station dd number of SYSOUT copies DF4201I job volume DSN dsname COPY INCOMPLETE This message may occur if the command DJ has been entered Before transmission or after receiving the data set dsname on volume volume a copy job job had been started This job is not yet complete DF4202I NO INCOMPLETE JOBS FOUND This message occures if the command DJ has been entered and there was no oncomplete copy job DFA2F2I NO INCOMPLETE JOBS FOUND This message occurred if the command DP has been entered and there was no incomplete rvsFTP job DF42F5P xx SID sid DSN FTP control dataset name DFA2F6I xx SID sid DSN real dataset name DF42F7P xx SID sid CD dd mm yy CT hh mm ss DF42F8P xx SID sid SD dd mm yy ST hh mm ss DF42FBP These messages occurre if the command DP has been entered and there were incomplete rvs
51. dsname already exists The data set will reside on disk under a temporary name with timestamp DATASET ALREADY CATALOGED AND NOT RE RENAMED RC DATASET NOT CATALOGED AND NOT RE RENAMED RC The received data set could not be cataloged after reception but has already been renamed to its final name While renaming it back to its temporary name an error occurred For return and diagnosis codes xxxx xxxxxxxx see DFSMS MVS Diagnosis Reference The data set will reside uncataloged under its final name on disk DATASET NOT UNCATALOGED dsname The temporary data set with timestamp dsname has been renamed to its final name but could not be uncataloged R sid mn dsname nnn RE VOL volume status Receiving of the data set dsname on volume volume terminated nnn records have been received status may be KEEP The transmission ended normally the displayed END disposition has been executed LCATLG CANCELLED The transmission has been cancelled by operator ABEND xxx yyy The transmission terminated abnormally Xxx system completion code yyy user completion code 73 rvsMVS Messages and Codes 5 rvs Messages DF3726P DF3727E DF3728E DF3729E DF3730P DF3731I DF37321 DF3733E DF3734E R sid mn DYN UNALLOC CODE xxxx yyyy If at start of receiving the data set is already allocated this data set will be unallocated and than once again allocated The messag
52. dynamically This ABEND is coded in the program DF077Cxx No jobs PDS specified in the dynamic allocation module DF067A This PDS contains data set related JOB s which are to be started after reception in order to process these data sets In later rvs releases since rvs OS Release 3 2 it is also possible to specify Partitioned Data Sets in the resident receive entries This ABEND is coded in the program DF077Cxx The module DFO67A contains no valid dsname entry for a PDS containing JOB s to process the received data sets An error occurred during access to the rvs Log Data Set USP User Separation A MODCB GENCB or SHOWCB macro could not be executed or the log data set could not be opened This abend may occur if a new Log Data Set has been created but not initialized If this abend occurs within the ISPF panels of rvs the reason may be insufficient access authority for the rvs log data set required authorization ALTER This ABEND is coded in the program DFO54Yxx The rvs LOGLOG Data Set is full This ABEND is coded in the program DFO054Yxx The installation exit DFUX001 ended with a nonzero return code This ABEND is coded in the program DFO54Yxx An error occurred during access to the rvs log record A record was found in the control data set that could not be de compressed This ABEND is coded in the program DFO90Axx Should not occure error The execution of aMODCB macro failed This ABEND is coded in the program D
53. e by the X 25 network So some of the occuring diagnostic codes are used only by the national telephone company responsible for the X 25 network this means it might be necessary in some cases to ask the national telephone company for the meaning of some of these codes Additional if the remote side uses non IBM equipment some of the codes may have other meanings 6 1 X 25 Cause Codes 6 1 1 Cause Codes within clear indication packet DTE originated When the cause code is X 00 the diagnostic code field has been passed through the network from the remote DTE s original Clear Request packet Number busy Invalid facility request Network congestion Out of order Access barred Not obtainable Remote procedure error Local procedure error RPOA out of order Reverse charging acceptance not subscribed Incompatible destination Fast select acceptance not subscribed Ship absent rvsMVS Messages and Codes 6 X 25 Cause and Diagnostic Codes 6 1 2 Cause Codes within reset indication packet DTE originated When the cause code is X 00 the diagnostic code field has been passed through the network from the remote DTE s original Reset Request packet Out of order Applicable to permanent virtual circuits only Remote procedure error Local procedure error Network congestion Remote DTE operational Applicable to permanent virtual circuits only Network operational Applicable to per
54. error DF83051 727777777777777777777777727777777797777777777777 This message is issued by the rvs TCP IP task in order to display a longer message text describing an error number DF8306E INITAPI FAILED ERROR This message is issued by the rvs TCP IP task when initapi failed The TCP IP task is terminated after this event DF8307E API MODULE COULD NOT BE LOADED This message is issued by the rvs TCP IP task when the TCP IP interface is not available The TCP IP task will be terminated after this event Note For some functions the MVS C runtime library is neccessary in order to satisfy the request E g for the the function GETHOSTBYNAME assigning the IP address to a specified host name using name servers the c runtime library is mandatory DF8308P A 2222 COMPLETE S P IP ADDR HHH This message is issued by the rvs TCP IP task when an IP connection has been established either after connect or accept The message shows the socketnumber remote portnumber and remote IP address An OFTP task will be started after this event DF8309W SESSION START REJECT NO RESOURCE TCB AVAILABLE 117 rvsMVS Messages and Codes 5 rvs Messages DF8310I DF8311P DF8312P DF8313E DF8314P DF8315I1 DF8316E DF8317P DF8318P This message is issued by the rvs TCP IP task in response to an operator activate station command if no resources tcb are available to handle a call request
55. following functions CNSLSUP suppression of console messages CNSLDSPL display of console messages RMOPSUP suppression of messages for remote operating session RMOPDSPL display of messages for remote operating session name denotes the name of a message subset which must be defined within the CNTLMSG member of the rvs tables data set For a detailed description of this member see rvsMVS Installations Manual rc denotes the returncode of the processed command The following return codes may occur 00 command has been processed successfully 04 specified message subset name not defined in CNTLMSG member 08 CNTLMSG member not available allocated 55 rvsMVS Messages and Codes 5 rvs Messages DF3040I MSG REFRESH PROCESSED This message occurs if the command MSG REFRESH has been entered the command has been processed successfully DF3040I MSG DISPLAY CS namel RS name2 CD name3 RD name4 DF3040I MSG SETDEF CS namel RS name2 CD name3 RD name4 This message occurs if one of the commands MSG DISPLAY or MSG SETDEF has been entered The command MSG SETDEF first resets the functions to the defined default message subsets The message shows which message subsets are currently assigned to the different functions CS suppression of console messages RS suppression of messages for remote operating session CD display of console messages RD display of messages for remote operating session DF3040I MSGOUT PROCESS
56. header record has been received with the indication to receive the data set dsname DF3702E R sid mn DYNAMIC ALLOCATION ERROR xxxx yyyy The allocation of the output data set failed For a description of the error reason code xxxx and the info reason code yyyy see OS VS2 MVS SPL Job Management DF3702E R sid mn OUTPUT DATASET ALREADY IN USE A data set is to be received but the output data set is just used by another task within the rvs monitor This situation should normally not occur One reason for this might be that files from different remote stations shall be stored in the same output file as specified in resident receive entries and the replace function is also used If this situation is detected the transmission will be cancelled and dynamic allocation error 0210 99 is used as error indication DF3703P R ORT MO ENQ ISSUED FOR SYSDSN name DF3703P R ORT MO GDG ENQ NOT AVAILABLE SYSDSN name Message DF3703P is for error detection only They are not in effect for users purpose DF3704E R sid mn NO ACTIVE KD RECORD FOUND RESTART IS IMPOSSIBLE A restart is required but the active entry in the rvs control data set has been deleted The whole file must be transmitted once more DF3705E R sid mn REQUIRED VOLUME volume NOT MOUNTED The disk volume volume is requested to receive a data set If the specified volume cannot be mounted the record of the control data set must be changed to receive the data set on ano
57. is available only for access method X25 LU62 and TCPIP The parameter is ignored WARNING USER LEVEL SECURITY NOT INCLUDED IN CURRENT LICENCE KEY IGNORED FOR SID XXX The ULS user level security ULS YES found in station entry for SID xxx but the user level security is not included in current licence key The parameter is ignored WARNING USER SEPARATION NOT USED SEE CNTL MEMBER IGNORED FOR SID XXX The user separation parameter USP YES found in station entry for SID xxx but the user separation is not included in current licence key The parameter is ignored WARNING ONLINE SECURITY NOT INCLUDED IN CURRENT LICENCE KEY IGNORED FOR SID XXX 44 rvsMVS Messages and Codes 5 rvs Messages The online security parameter SECURITY ONL found in station entry for SID xxx but the online security is not included in current licence key The parameter is ignored DF2261W WARNING ONLINE SECURITY ONLY SUPPORTED FOR ACESS METHODS X25 LU62 TCP IGNORED FOR SID XXX The online security parameter SECURITY ONL found in station entry for SID xxx but the online security is available only for access method X25 LU62 and TCPIP The parameter is ignored Messages of program DF022C Online refresh of the internal station table DF22COI ONLINE STATION REFRESH STARTED LEVEL nn nn nn nn nn First message of program DF022C Processing of online refresh of the internal Station Table starts The program level is stated DF
58. is coded in the program DF049Dxx The rvs command DQ has been entered to display the data sets queued for transmission active send requests During reading the active send request entries of the rvs control data set an error occurred Abend within the rvs dispatcher routine posted ECB not found Should not occur error Abend within the rvs dispatcher routine stations table not available Should not occur error 12 rvsMVS Messages and Codes 3 rvs Abend Codes 540 545 546 550 551 561 563 565 566 580 591 599 21C 221 222 226 227 231 233 235 236 244 24F 257 An error occurred during access to the rvs Control Data Set A MODCB GENCB or SHOWCB macro could not be executed or the control data set could not be opened This abend may occur if a new Control Data Set has been created but not initialized If this abend occurs within the ISPF panels of rvs the reason may be insufficient access authority for the rvs control data set required authorization ALTER This ABEND is coded in the program DF054Cxx The rvsLOG Data Set is full Use procedure PDF0014A see INSTALLATIONS MANUAL to reset the data set This ABEND is coded in the program DF054Cxx The installation exit DFUX001 ended with a nonzero return code This ABEND is coded in the program DF054Cxx An error occurred during access to the rvs control record A record was found in the control data
59. is kkkk K bytes space may be substituted by PVT BRUTTO or PVT TOTAL That means PVT gt private area BRUTTO gt all used 4k pages are counted TOTAL gt all subpool space is added up This message appears in certain time intervals which are controlled by the rvs start parameter STORAC or if the command STORAC has been entered See rvsMVS Installations Manual or rvsMVS Operations Manual This message is not displayed on console PRIV AREA xxxxxK FREE yyyyy K USED zzzzz K This message is displayed in conjunction with message DF2000P if rvs is running in a non MVS XA environment There is a PRIVATE AREA of xxxxx K The free space of this area is yyyyy K the used space is zzzzz K This message is not displayed on console ALLOCATED PRIVATE STORAGE nnnK BELOW 16 MB UNALLOCATED PRIVATE STORAGE mmmK BELOW 16 MB MAX REGION SIZE rrrK BELOW 16 MB This message is displayed in conjunction with message DF2000P if rvs is running in a MVS XA environment nnn denotes the size of virtual storage below 16 MB which is currently used by the rvs monitor 38 rvsMVS Messages and Codes 5 rvs Messages rrr denotes the maximum available region size on the host below 16 MB this value is independent of the regionsize which is valid for the rvs monitor for example as specified within the REGION parameter of the EXEC card mmm denotes the size of currently unallocated virtual storage be
60. purposes of checking the following data are displayed after reception of a data set al number of data blocks received a2 number of data blocks transmitted b1 number of line blocks received b2 number of line blocks transmitted c1 number of characters received c2 number of characters transmitted R sid nnn REQ SPACE nnnnn BLOCKS NOT AVAILABLE For additional information see message DF3502E The output data set could not be allocated because the space required nnnnn blocks is not available This message may appear when a particular receive volume has been specified in a resident receive entry Action e make enough space available on the volume concerned e specify another volume e make sure that a space allocation on work volumes is possible don t specify a volume in the resident receive entry R sid LOCATE MACRO FAILED FOR dsn R sid LOCATE FAILED RC xx yy DSN dsn A data set is to be received from station sid this data set is to be cataloged at the end of the transmission The received data set is treated as a GDG data set Therefore the current generation must be determined But this is not possible because the LOCATE macro failed xx and yy denote the returncodes content of reg 15 and reg 0 of the LOCATE macro dsn denotes the data set name as used for the LOCATE macro One reason may be that no GDG base has been defined for this data set After this rvs tries to catalog the received data set wi
61. response to a start file transfer request In the message is shown the code used in the SFNA protocol unit Refer to the document Odette specifications for file transfer for a further explanation of the code The second line of the message indicates the corresponding dataset name of the SFNA If the error code in the SFNA indicates Invalid Origin or Invalid Destination an additional line is issued in which the rejected ODETTE identification is displayed This message is issued by the Odette File Transfer Protocol task when an error occurs during allocation or un allocation of a data set In the message is shown the return code from the allocation request and the volume and dataset name of the file for which the error occurred Z sid accm sessonid OPEN FAILED FOR VOL volume DSN dsn This message is issued by the Odette File Transfer Protocol task when a dataset to be sent or received could not be opened In the message is shown the volume and dataset name of the file for which OPEN error occurred Z sid accm sessonid DSN dsn VOL volume RESTARTS AT checkpoint 154 rvsMVS Messages and Codes 5 rvs Messages DF9415I DF9416W DF9417P DF9418E DF9419E DF9420E This message is issued by the Odette File Transfer Protocol task when a file transfer is restarting ie a previous attempt has been made to transfer the file The restart point is indicated in the message and is expressed in records or 1K blocks depending on t
62. screen of the remote operator see Installations Manual receiving of data transmission of data used for display of internal trace data indication of speed velocity message concerning start of rvs traces message concerning stop of rvs traces VTAM sessions are denoted by O S R operator communication transmission of data sets receiving of data sets O S R indicates the type of a VTAM session If there is defined more than one session of the same type to the same station the session type is followed by increasing numbers e g R1 first receive session R2 second receive session etc 25 rvsMVS Messages and Codes 5 rvs Messages DFOOOII nn NO RESPONSE ON OUTGOING CALL SID LU 77 This message is issued by the rvs X 25 CTCP task when no response on outgoing call is received The message shows the failing request the Logical Unit that issued the request and and the station identification If a VTAM request fails for the X 25 link Logical Unit the CTCP task will start termination DFOOO2I nn CTCP 222272222 22222222 LV 2 2727272727272722722 This message is issued by the rvs X 25 CTCP task in response to a STATUS_CTCP command The message shows the status ACB name used by the CTCP task and the name of the local unit used for X 25 link communication Also the packet size and windows size used for the X 25 connection is shown DFO1O01I T sid TRACE STOPPED ALLOCATION ERROR CODE xxxx
63. sent files to any remote station The ID of the remote station and the virtual file name for the transmission are displayed NUMBER OF ACTIVE ENQ RESOURCES nnn mmm SNA ODETTE 89 rvsMVS Messages and Codes 5 rvs Messages DF5220P DF5221P DF5233P DF5234P DF5235P DF5236P This message is displayed as response to command DD ENQ It displays the summary of the currently sent files nnn files are sent on SNA sessions mmm files are sent on ODETTE sessions X 25 LU6 TCP FTP S sid acme nm CALL OF EXIT DFUX001 INITIATED COMPLETE This message appears when the dispatcher selects a file for transmission Execution of exit DFUX001 is displayed in this message S ORT ACME 12345678 SERIALIZATION TRANSMISSION IN PROGRESS This message appears when the dispatcher selects a file for transmission S sid acme nm START SELECTION OF SEND REQUEST This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates that selection of a send request for send session nm to station sid and access method acme has started SUCCESSFUL END SELECTION OF SEND REQUEST S sid acme nm t UNSUCCESSFUL END SELECTION OF SEND REQUEST This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates that selection of a send request for send session nm to station sid
64. sequence Invalid packet type received Control packets except Reset Indication received in state P4 Unassigned logical channel number Timer expired for interrupt confirmation or D bit not support Packet too short Packet too long Invalid GFI rvsMVS Messages and Codes 6 X 25 Cause and Diagnostic Codes Not identifiable Not supported Invalid P S Invalid P R Invalid D bit received Invalid Q bit received No LU MCH session active for GATE DATE Abend 0703 in progress Host negative response or cancel chain command PCNE negative response with D bit PCNE SHUTC status XIO disable Unauthorized interrupt confirmation Unauthorized interrupt request PCNE error RESET sent to PAD for SIGNAL Resources general In state P1 incoming call received slowdown in progress PIU too long Local procedure error general Packet received with LC not equal to 0 Restart or diagnostic packet received with LC not equal to 0 In state P1 incoming call received and not available for ic Facility not subscribed Invalid packet for LC equal to 0 In state P1 incoming call received with inv facility field Facility not supported Unexpected calling DTE Invalid D bit request Reset indication on virtual call Invalid protocol identifier Connection identifier mismatch 6 2 3 Diagnostic Codes from the network The following sectio
65. set that could not be de compressed Please use program DF144A to find and delete the incorrect record s This ABEND may occur after activation of a BSC line During initialization of the line control program a BTAM terminal list could not be created because there are too many entries within the rvs stations table which have defined this line as a subchannel to be used The maximum of 200 station table entries is exceeded This ABEND is coded in the program DF056Bxx During initialization of a transmission the BTAM line control was not able to switch from receive to send by RESETPL This ABEND is coded in the program DF056Bxx The program profile specified does not exist in the member PROGPROF of the rvs TABLES Data Set This ABEND is coded in the program DF056Bxx Error during update the rvs control data set This ABEND is coded in the program DF056Bxx Too many stations defined for a line Should not occur error This ABEND is coded in the program DF058Axx During the initial phase of the RJE protocol no related entry could be inserted in the rvs control data set No program output is send back This ABEND is coded in the program DF059Cxx The rvsMVS monitor is searching for a disk UCB but no disk UCB has been found This ABEND is coded in the program DF059Cxx During the termination of a transmission the transmission related active 13 rvsMVS Messages and Codes 3 rvs Abend Codes 640 645 646 650
66. specified which is larger than the number of blocks records of the entire data set to be transmitted 036 024 During restart a block number or record number has been specified which exceeds the number of blocks records already received 040 028 A restart has been requested although the data set has not yet been transmitted 044 02C The sequence number of a received line block is out of sequence rvsMVS Messages and Codes 2 rvs User Codes 048 052 056 060 064 068 072 076 080 084 088 092 096 100 104 108 112 030 034 038 03C 040 044 048 04C 050 054 058 05C 060 064 068 06C 070 Error during the try to add a new record to the control data set Error when opening the data set to be transmitted or received During a data interchange with IBM 34 or 36 computer the maximum record length of 2000 bytes has been exceeded Invalid record format specified in the rvs protocol header record H record LRECL or BLKSIZE has not been specified in the rvs protocol header record H record The BLKSIZE specified in the rvs protocol header record H record exceeds the track capacity of the used disk a deblocking is not possible The record count specified in the rvs protocol header record H record does not match the required record number of the rvs protocol answer record A record The data set could not be opened The number of th
67. stack nn has ended abnormally An automatic re activation attempt is initiated In case of failure it is repeated once per minute until activation is successful or a stop command for this control task is entered DF3057E F SID CMD NOT EXECUTABLE STATION NOT DIRECTLY CONNECTED A command for station sid e g A sid or T sid has been entered This command is not executable because the specified station is not directly connected but may be accessed via a relay station Command X sid may be used to display via which other station the specified station sid is connected In this case commands like activate stop trace etc are valid only for the directly connected relay station DF3059I x SPECIFIED STATION sid ALREADY ACTIVE The message occurs if the command A sid for a X 25 station has been entered and the specified station is already active SPECIFIED STATION sid NO SCT ENTRY FREE The message occurs if the command A sid for a X 25 station has been entered and SCT Session Control Table not free entry exist Check the parameter MAXSVC in CNTL table x SPECIFIED STATION sid MAX SESSION ACTIVE 59 rvsMVS Messages and Codes 5 rvs Messages DF3060I DF3061W DF3062W DF3062W DF3201P DF3202P DF3203P The message occurs if the command A sid for a X 25 station has been entered and the maximum sessions for this station sid exist check the paramete
68. the data set dsname on volume volume could not be changed because such an entry could not be found COMMAND F ALL COMPLETED This message is a response to one of the commands S ALL or H ALL These commands may be used to set all send requests into hold state H ALL or to release all send requests from the hold state S ALL f sid DATASET dsname ALREADY TRANSMITTED This message indicates that the file dsname has already been successfully transmitted and the remote station has sent a response back in order to inform the sender about the successful file transfer A retransmission of this file is not possible the send request will not be changed f sid INVALID PARAMETER VALUE NEWSID sid2 SPECIFIED This message is a response to the command S sid name NEWSID sid2 The station ID of the remote station should be changed from sid to sid2 but the new station ID sid2 is invalid not defined within the rvs stations table The station ID will remain unchanged F ORT DATASET name JUST TRANSMITTED F ORT JOBNM XXXXXXXX JOBNR XXXXXXXX OWNER XXXXXXXX SYSTEM XXXXXXX For FTP component only This message indicates that the file dsname has already been just successfully transmitted F ORT INVALID REPLY REENTER COMMAND Invalid reply of the command S sid name Please reenter command S sid DSN dsname VOL volume The transmission of the data set dsname is starting In the event of an restart the point a
69. the next data traffic indicated by display of message DF5503 101 rvsMVS Messages and Codes 5 rvs Messages DF5507E DF5508E DF5509E DF5510E DF5511E DF5512E DF5513E DF5514E DF5515E 111 111 LINE IS NOT DEFINED WITHIN STATIONS TABLE An activation command for line Ill has been entered but there is no line entry for the switched line Ill within the rvs stations table The line control will be terminated with user code 100 after this message f l11 111 NO PROGRAM PROFILE FOUND FOR THIS LINE An activation command for line Ill has been entered but the program profile defined for this line rvs stations table has not been found within the rvs program profile table The line control will be terminated with user code 100 after this message f sid 111 PROGRAM PROFILE ppp NOT FOUND A line connection with station sid on line Ill has been established During identification phase the program profile ppp defined for station sid is used but this profile is not defined within the rvs program profile table The line connection with station sid will be broken after this message f sid 111 PASSWORD MISSING TO CONNECT THE LINE Additional to the identification a password exchange after identification is defined for station sid see rvs stations table But the expected record type for password exchange has not been received from sid after identification After this the line conn
70. to station sid has been established using line Ill During transmission sending or receiving of a dataset rvs received an invalid record type neither protocol record nor data record rvs ignores this record the transmission will be continued The reason for this error may be e the remote station does not handle the used transmission protocol in a correct way e the transmission protocol which is defined to be used for the remote station sid see member PROGPROF in the rvs tables dataset described in the rvs interface description is not correct This means the transmission protocol defined for station sid does not meet the protocol specifications which the remote station is able to process An rvs trace may be used to obtain more information DF5742E S sid 111 TRANSMISSION OF dsname REJECTED DF5743E S sid 111 REMOTE STATION DOES NOT SUPPORT PDS TRANSFER FUNCTION The partitioned dataset with name dsname should be transmitted to station sid on line Ill During start of this transmission rvs detected that the remote station does not support PDS transfer As a result of this situation the dataset cannot be transmitted the send request is placed in hold state and the line connection will be broken The send request for this dataset should be deleted because it cannot be assumed that the remote station will be able to support PDS transfer in the next time 108 rvsMVS Messages and Codes 5 rvs Messages Thi
71. xxxxxx ALL VOLUMES OF UNIT yyyyyyyy OCCUPIED J This message is always issued in relation with msg DF88X1E and shows a short explanation of the DYNALLOC macro return code XXXXXX volume number yyyyyyyy unit number DF88X3P F sid acme sessid TEXT POINTERS ADDR xxxxxxxx TEXT UNIT unitname This message is issued in case of a dynamic allocation error It will display the contents of the used SVC 99 parameter list allocation request block text pointer list and text units DF88X5P KDUPDAT 88X TYP This message is issued by the FTP task List internal action of FTP task with KD control file For internal use only 138 rvsMVS Messages and Codes 5 rvs Messages NOT CATALOGED DF88Y1W F sid dsn NOT UNCATALOGED RC xx yy NOT DELETED J A successful sent dataset should be deleted uncataloged resp a successful received dataset should be catalogued The action failed xx denotes the return code hex of the SCRATCH CATALOG macro The status code yy hex is only issued by the SCRATCH macro For a further description of the codes see IBM manual OS VS2 SPL Data Management DF88Y2E F sid CREATION OF SEND REQUEST FAILED DF88Y2W F sid dsn NOT QUEUED TO STATION xxx A received dataset dsn should be automatically passed by to a final station xxx but could not be queued for sending DF88Y3P R sid mn 2222722227222 222222 PPP PPPP PIPPI This message is issued by the Odett
72. 0A0B OCODOEOF 0123456789ABCDEF Messages DF3744lI until DF3745P are for error detection only They are not in effect for users purpose DF4101I f sid mn dsname volume nnnnnn BL day time sid2 JOBNAME jobname This message appears as a reply to the commands DS DR or DQ The contents of some parameters of this message depends on the type of command entered The meaning of the parameters is f Q the message is related to files queued for transmission R the message is related to files which are just to be received S the message is related to files which are just to be transmitted dsname name of a data set which is queued for transmission transmitted or received volume volume the data set dsname resides nnnnnn number of blocks which have been transmitted day time day and time the data set has to be queued for transmission or has been received sid2 stations identification of the first or final station jobname name of the job which is to be automatically started in case of the received data set has to be printed DF4102I NO RECORDS FOUND This message appears as a reply to control data set queries DF if no records have been found in the control data set DF41031 MORE THAN 100 ENTRIES FOUND DISPLAY IS INCOMPLETE This message appears as a reply to control data set queries DF when more than 100 entries have been found In this case only the first 100 entries that are found in the control data set will be
73. 1 DF51001 DF5102A DF51031 as having at least 12 characters the second message appears if no data set beginning with name was received or transmitted within the last 7 days SYSOUT class FORM form DEST dest COPIES n This message appears in relation to message DF50011 after the entry of N sid f or DF if the data set concerned was placed in the output queue of the receiving computer The parameters correspond to the job control parameters N sid INVALID REPLY Incorrect operator entry DS NAME DEV VOL DISP JOB TRKS TO This message appears as a reply to the commands N sid RR name or N sid RS name The message occures only if resident records have been found It is the head line for the following message name The message displays parameters for the data set with DSNAME name The dispalyed parameters if specified in a resident control data set entry are device typ volume number disposition jobname Space capacity in traks and the final receiver of the data set This message occures always in conjunction with DF50071 N sid NO RESIDENT RECORDS FOUND NO END TO END RESPONSES FOUND One of the commands N sid RR name or N sid N name was entered and no resident receive entry or no end to end response for data sets with a dsname starting with name has been found N sid MORE THAN 100 ENTRIES FOUND DISPLAY IS INCOMPLETE This message appears as a reply to control data set queries n
74. 1 022 023 012 013 014 015 016 017 Lineblock is out of sequence Blocksize in header exceeds track capacity A wrong record count in trailer has been received Length of data exceeds line buffer Error during data de compression Replace function A data set has been received for which the space has to be enlarged This request could not be satisfied 4 1 Dynamic allocation errors Code Code decimal hexadecimal Meaning 040 028 Data set is allocated to another job or user 041 029 Unit or internal reader not available 042 02A Requested volume is not mounted 043 02B Unit name is not defined 044 02C Volume is not available 045 02D Device type does not have enough units 046 02E Data set associated to ddname is open 047 02F Data set exits on all volumes of unit group 048 030 Insufficient space in the VTOC 049 031 Space could not de obtained because of I O Error 050 032 Absolute track is not available 051 033 Insufficient space on storage volume 052 034 Space request rejected by DADSM Exit 053 035 Requested space is not available on any volume In case that serious errors occur which can not be handled by rvs sense codes 004 006 or 010 the data set to be transmitted is set into HOLD status That means a new attempt to transmit the data set can be initiated by the operator or by system after an appropriate time interval 23 rvsMVS Messages and Codes 5 rvs Messages
75. 13 191 rvsMVS Messages and Codes 6 X 25 Cause and Diagnostic Codes CLEAR PACKET received Diagnostic Meaning Possible error Code hex se 40 If all SVCs are busy call setup problem 21 24 The dialed X 25 number belongs to a multichannel link which might be generated not properly check compatibility with generation of PTT too If rvs tries to establish a connection and a clear packet has been received on outgoing call remote application is not active If rvs tries to establish a connection possibly a wrong number has been called wrong number specified for parameter X25NUM in STATIONS Table Possibly the value specified for the rvs start parameter WSIZE is not the same as generated for the X25 multichannel link by the national telephone company 192 rvsMVS Messages and Codes 7 rvs Start Messages 7 rvs Start Messages This section describes most important rvs start messeages can t open trace config file DD EXTCONF This message occurs if the DD statement EXTCONF isn t defined in rvs start procedure This DD statement allocates a configuration file used for advanced capabilities This is a warning and currently for internal use only 193 rvsMVS Messages and Codes Index BSC 13 29 30 48 51 54 55 82 84 95 96 106 107 108 Command DD 14 15 17 19 30 38 39 52 83 84 85 140 DDR 93 DDS DF 13 15 73 76 77 80 81 100 101 137 DJ 73
76. 1412P DATASET NOT RENAMED RC xxxx xxxxxxxx dsname The temporary data set could not be renamed after reception For return and diagnosis codes XXXX XXXXXXXX see DFSMS MVS Diagnosis Reference dsname denotes the old data set name timestamp This message is followed by DATASET TARGET NAME dsname The message displays the new data set name of the failed rename DATASET GDG LOCATE RECOVERY NO NEW VERSION EXISTING The current GDG version could not be renamed cataloged rvs checks whether the current version of the GDG is still the highest version If the current version is not the highest rvs determines the next new version and tries to rename catalog this new version This message displays that recovery by increasing of the version number is not possible DATASET ALREADY CATALOGED dsname The received data set could not be cataloged after reception because a data set with identical name dsname already exists The data set will reside on disk under a temporary name with timestamp DATASET ALREADY CATALOGED AND NOT RE RENAMED RC DATASET NOT CATALOGED AND NOT RE RENAMED RC The received data set could not be cataloged after reception but has already been renamed to its final name While renaming it back to its temporary name an error occurred For return and diagnosis codes xxxx xxxxxxxx see DFSMS MVS Diagnosis Reference The data set will reside uncataloged under its final name on disk
77. 222222222 153 rvsMVS Messages and Codes 5 rvs Messages DF9410E DF9411E DF9411E DF9411E DF9411E DF9412E DF9413E DF9414I This message is issued by the Odette File Transfer Protocol task when an End of Session ESID protocol unit has been sent or received In the message the code used in the ESID protocol unit is shown code reason 00 normal termination 01 command not recognised 02 protocol violation 03 user code not known 04 invalid password 05 local site emergency closedown 06 command contained invalid data 07 NSDU size error 08 resources not available 09 time out 10 mode or capatibility error 99 unspecified abort Z sid accm sessonid UNEXPECTED FPDU RECVD STATE nn IC mm This message is issued by the Odette File Transfer Protocol task when an unexpected protocol unit is received ie in the current state of the protocol a certain protocol unit is expected but instead another protocol unit is received The state and information code values indicate in which situation the error occurred State and info code values are described in message DF9403 S sid accm sessonid NEG RESP TO START FILE RECEIVED CODE nn S sid accm sessonid REJECTED FILENAME dsn S sid accm sessonid ORIGINATOR sfidorig optional S sid accm sessonid DESTINATION sfiddest optional This message is issued by the Odette File Transfer Protocol task when a Start File Negative Answer SFNA protocol unit is received in
78. 22C1I NUMBER OF ADDED MAIN ENTRIES nnnn Number of Station Table main entries that have been added to the internal Station Table DF22C2I NUMBER OF ADDED SUB ENTRIES nnnn Number of Station Table sub entries that have been added to the internal Station Table DF22C3I NUMBER OF REPLACED ENTRIES nnnn Number of Station Table entries that have been replaced by a Station Table entry of same station identification SID but with changed access method ACME DF22C4I NUMBER OF UPDATED ENTRIES nnnn Number of Station Table entries where changes have been made in one or more than one of the Station Table parameters DF22C5I SIZE OF APPC NODE TABLE ANT TO SMALL RE START rvsL More than 200 new LU6 2 Station Table entries have been added to the Station Table Re start the LU6 2 component of rvs to make the new entries active DF22C6I ONLINE STATION REFRESH ALREADY ACTIVE The Station Table Online Refresh is already active Wait for termination of the previous command REFRESH STATIONS DF22C9I ONLINE STATION REFRESH ENDED The Station Table Online Refresh has terminated successfully DF2301E A sid SESSION PROFILE sss NOT FOUND ON SESSION TABLE 45 rvsMVS Messages and Codes 5 rvs Messages DF2302E DF23031 DF2304I DF2305I DF2401E DF2402E DF2403E DF2404E DF2405E DF2406E DF2407E DF2500E In the stations table station sid is defined with a sessions profile sss This profile could
79. 24 460 461 5E6 5E7 5E8 67E 69A 69B 6B8 6BB 6C2 This ABEND is coded in the program DF078Cxx See rvs User Code 1019 This ABEND is coded in the program DF106Cxx Error during decompressing received data records This ABEND is coded in the program DF112Bxx During expanding compressed data the output buffer size has been exceeded his ABEND is coded in the program DF121 Axx The number of the storage information areas or the number of the CSA subpool descriptors exceeds the boundary Should not occur error This ABEND is coded in the program DF151Axx Invalid specification of PARM entry This ABEND is coded in the program DF151Axx Error during execution of the PUT RPL or SHOWCB macro Should not occur error This ABEND is coded in the program DF151Axx Error during execution of the GENCB OPEN ACB or CLOSE ACB macro Should not occur error This ABEND is coded in the program DFO66Bxx The module DFO67A could not be found This module must be available in order to allocate data sets dynamically The module contains data sets and if required passwords of data sets which are to be allocated See rvsMVS Operations Manual rvsDYN macro This ABEND is coded in the program DF169Axx The SYSPRINT DD statement is missing only if used as BATCH PGM This ABEND is coded in the program DF169Axx This abend occurs in different cases i e if no JOB name of the transmitted JCL is not available or if the out
80. 48040 DF48059 For a parameter of the command F sid a wrong value has been specified F sid INVALID INDEX For a parameter of the command F sid a wrong index has been specified F ORT F ORT F ORT F ORT F ORT NO GZIP LICENCE COMMAND IGNORED NO SECURITY LICENCE COMMAND IGNORED NO VIRTUAL STATION LICENCE COMMAND IGNORED NO USER STATION LICENCE COMMAND IGNORED NO TRANSFER RESTRICTION LICENCE COMMAND IGNORED The command F sid xxx is no valid licence X sid VTAM SUBTASK NOT ACTIVE The command X sid S will be executed only if the VTAM control task is active BTAM X sid ssid2 xx l telefone address ALIAS sid2 lvram As a reply to the operator command X sid2 or X sid the station name sid option byte xx of the stations table see rvsMVS Installations Manual section 4 4 access method telefone number address of the station sid and the alias name sid2 are listed LINE S 111 112 113 X sid sid2 SIZE nnnn J LLU S 1u1 lu2 1u3 J Reply of the command X sid L The alias name sid2 the used line buffer SIZE nnnn and the defined BTAM lines or VTAM logical unit names are listed Active lines are signed with an A behind the line name X sid sid2 PP program profile The complete program profile associated to station sid is listed as a reply to the operator command X sid P see section 4 4 3 X sid mn sid2 SS sessions profile A
81. 6E f sid mn text The error message text has been received from the remote station This message occures most times in conjunction with an abnormal terminated data set transmission S sid mn rvs PROTOCOL VIOLATION RECORD IGNORED A rvs protocol record has been received from the remote station sid This record is not within the rules of the rvs protocol The record will be ignored a just active data set transmission will be terminated S sid mn DISK READ PROGRAM ERROR SYSTEM sss USER uuu TRANSMISSION CANCELLED The module which is reading data from disk terminated with system completion code sss and user code uuu The transmission will be cancelled S sid mn LOGICALLY INVALID RECORD RECEIVED The contents of a just received rvs protocol record does not match the contents e g data set name ready time of the assigned rvs control data set record The transmission will be terminated S sid mn KD RECORD NOT FOUND During initialization of a transmission after reception of an rvs protocol record type A no assigned rvs control data set record with an active send request has been found in the control data set S sid mn dsname nnnnnnn RE VOL volume END KEPT Status report at end of transmission after trailer record has has been transmitted nnnnnnn number of transmitted data records S sid mn INVALID FEATURE xxxxxxxx in A RECORD During I A record exchange the remote and receiving station speci
82. 6E S sid acme nm text This message appears if the exit DFUX001 terminates with a return code of 8 for send session nm to station sid and access method acme text is a message of equal or less 80 characters which is passed to rvs by the exit DFUX001 DF5207P S sid acme nm ENQ USE RETURNCODE xxx DSN dsname This message appears only within the rvs protocol It indicates for send session nm to station sid and access method acme execution of an ENQ macro which is used for serialisation of datasets to be sent 86 rvsMVS Messages and Codes 5 rvs Messages DF5208P DF5209P DF5210P DF52111 DF5211P S sid acme nm DEQ HAVE RETURNCODE xxx DSN dsname This message appears only within the rvs protocol It indicates for send session nm to station sid and access method acme execution of a DEQ macro which is used for serialisation of datasets to be sent LIST OF SEND REQUESTS REFRESHED tttt tt iii jjj xxxx yyyy LIST OF EERP REQUESTS REFRESHED tttt tt iii jjj xxxx yyyy The dispatcher subtask looks within a defined time interval for send requests EEPR within the rvs control dataset in order to perform initiate autodial functions or sending of datasets on SNA sessions A list of these send requests is kept in core until next reading of send requests EERP is done refresh of this list Since version A22 of the Dispatcher in this message are included some new values tttt tt jji
83. 7 77777777 SID DF9478P Z ORT ACCM SESSID CALL PARM 77775 77777477 77777777 DF9480E Z ORT ACCM SESSID RESTRICTION TABLE ERROR NO RECEIVE DF9481E Z ORT ACCM SESSID PERMISSION TABLE ERROR NO RECEIVE DF9483E Z ORT ACCM SESSID ONL TASK ABEND SID DSN name DF9484P Z ORT ACCM SESSID ACTIVE ONL TASK HAS BEEN DETACHED SESSION DF9485P Z ORT ACCM SESSID used user separation USP sibcousp DF9486P Z ORT ACCM SESSID used user separation USP siboousp DF9487P Z ORT ACCM SESSID used user separation USP sibpousp Messages DF9471P until DF9487P are for error detection only They are not in effect for users purpose DF9488P WAIT FOR EFPA TIME 444 This message is issued by the Odette File Transfer Protocol Task if a session is to be cancelled but no EFPA has been received in response to a sent EFID After 30 seconds the session is terminated in any case The message shows the action which is taken and the time stamp in hex mode 161 rvsMVS Messages and Codes 5 rvs Messages DF9490P DF9491P DF9492P DF9493P DF9494E DF9496P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9498P DF9499P k k NO CS RECORD FOUND DSN dsname xxx ORIGINATOR KNOWN SENT DSN dsname k MESSAGE REQUESTED Z ORT ACCM SESSID HEADER RECORD 7 777 7 7 17777777 SENT DSN name
84. 777 7799999999977 7799799999999 First 54 characters of the KD record Protocol message only This message is for possible error detection only It is not in effect for users purpose D 22727272222 USED TRANSLATION TABLE ADR aaaaaaaa The message indicates a translation table is used for send request Comp Secr This message is for possible error detection only It is not in effect for users purpose D 227272727272 USED FILE FORMAT VAL aaaaaaaa The message indicates which file format is used for send request Comp Secr This message is for possible error detection only It is not in effect for users purpose D message Message DF5N71P is for possible error detection only It is not in effect for users purpose D message Status Message from the Service Provider Task send request This message is for possible error detection only It is not in effect for users purpose D message Message DF5N80P is for possible error detection only It is not in effect for users purpose D HHH 272727777 777777272 77777777 7777777 cic This message is issued if an internal modul trace will be processed Protocol message only 96 rvsMVS Messages and Codes 5 rvs Messages Messages of the Receive Dispatcher Task DF5VOOI D RDS DRIVER TASK 277272727 2222222222222 2722222722222 This message will be issued by the D command For more explanation re
85. 9101M DF9103P DF9105E within a certain time Additional information same as for VTAM REQUEST A sid SESSION REJECTED ISTATUS INACTIVE A request for establishing a session with station sid has been rejected because the stations entry is not released until now ISTATUS can be changed dynamically by the Operator see rvs Operations Manual if neccessary COMMAND B sid REJECTED FOR STOP OF SESSION INACT LU luname The command B sid has been entered for station sid which is connected to rvsMVS via one or more SNA sessions This command will be rejected for all SNA connected stations The reason for this this command might cause errors like system abend 0A9 of rvsMVS If a session to a remote station cannot be stopped with the P sid or C sid command the logical unit uname should be set inactive within the VTAM environment in order to terminate the session ALLOC ERROR xxxx yyyy ddname DSN dsname An error occurred during the allocation of the data set dsname and ddname For significance of XXXX error reason code yyyy information reason code see OS VS2 SPL Job Management JOB RECORD jobname jobid NOT FOUND JA Job Active record type assigned to the job jobname jobid not found in the rvs control data set UNALLOCATION FAILED FDBK xxxxxxxx An error occurred during the unallocation of the output data set see OS VS2 System Programming Library Job Management OUTPUT DATA SET HAS BEEN DELETED Aft
86. 962 This ABEND is coded in the program DF024Bxx The name of the input data set of the copy program DF024A00 is invalid 19 rvsMVS Messages and Codes 3 rvs Abend Codes 2403 2404 3002 3003 3004 963 964 BBA BBB BBC This ABEND is coded in the program DF024Bxx The name of the output data set of the copy program DF024A00 is invalid This ABEND is coded in the program DF024Bxx An invalid volume number has been specified for the input data set which is to be copied by the program DF024A00 This ABEND is coded in the program DF130B00 Error in the ECB structure a posted ECB has not been found The abend indicates an error which should not occur A dump is required for analysis of the problem This ABEND is coded in the program DF130B00 The rvs log data set is completely filled see message DF3016A This ABEND is coded in the program DF130B00 The message output task of the rvs monitor module DF031C terminated abnormally further processing of the monitor is impossible The abend indicates an error which should not occur A dump is required for analysis of the problem 20 rvsMVS Messages and Codes 3 rvs Abend Codes This page will be intentionally empty 21 rvsMVS Messages and Codes 4 rvs Sense Codes 4 rvs Sense Codes If during an active VTAM session a rvs protocol record is followed by a negative response the rvs protocol record flow will be interrupted and o
87. ATALOG macro IBM Brochure OS VS2 System Programming Library Data Management 66 rvsMVS Messages and Codes 5 rvs Messages DF3525W DF3525W DF3525E DF3526E DF3527E DF3528E DF3529E DF3530E DF35311 DF3532E DF36011 R sid NONZERO RETURN CODE OF INSTALLATION EXIT DFUX001 R sid ONLY INSTALLATION STANDARDS WILL BE USED TO RECEIVE dsname R sid RECEIVING OF dsname REJECTED BY DFUX001 See DF3735W DF3735E R sid text This message precedes the message DF3525W text is a message which is passed to rvs by the user exit R sid DATASET dsname ALREADY EXISTS ON VOL volume The data set dsname shall be received from station sid As a result of transmission control for example rvs start parameter VOLUME this data set is to be received on disk volume volume But a data set with this name is still existing on this disk volume In this case rvs does not modify the existing data set Receiving of data set dsname will be cancelled by rvs The file can be received from station sid only if a data set with this name does not exist on the specified disk volume R sid INVALID HEADER FIELD fieldname value A headerrecord has been received indicating that a data set is to be received This record contains an invalid value in one of its fields The name of the field and the value of this field is displayed in this message As a result of this error the transmission will be terminated with user code
88. ATASET The trace data set could not be open DF1001E f sid DATA SET NOT CATALOGED RC rc The monitor has attempt to catalog a received data set During the execution of the CATALOG macro the return code rc occurs See SPL OS VS2 Data Management for explanation of the return codes DF1002I f sid DATA SET HAS BEEN UNCATALOGED A data set is uncataloged after being queued for transmission DF1030P f sid DEMIGRATION PROCESSING STARTED FOR dsname A migrated data set is to be allocated either the file to be sent or a file to be replaced during receiving and startparameter DEMIG HSM has been specified dsname denotes the virtual filename of the transmission Demigration processing is handled in the same way as an allocation error After initiating the demigration processing the transmission will be cancelled A send request is set into atemporary HOLD status This message is followed by messages DF10311 and DF1032P DF10311 f sid RECALL COMMAND SENT TO HSM FOR dsname RC X rc A recall command has been sent to HSM to demigrate a file to be allocated rc denotes the returncode of the ARCHRCAL macro in hexadecimal dsname denotes the virtual filename of the transmission This message is followed by message DF1032P 28 rvsMVS Messages and Codes 5 rvs Messages DF1032P f sid PHYSICAL DATASET NAME dsname This message displays the physical data set name when a file is to be demigrated by HS
89. AVAILABLE VOLUME xxxxxx NOT MOUNTED DF1172E F sid REQUESTED UNIT yyyyyyyyy UNDEFINED VOLUME xxxxxx NOT AVAILABLE DS ALREADY EXISTING ON VOLUME xxxxxx ALL VOLUMES OF UNIT yyyyyyyy OCCUPIED This message is always issued in relation with msg DF1171E and shows a short explanation of the DYNALLOC macro return code XXXXXX volume number yyyyyyyy unit number REQUEST BLOCK DF1173P F sid acme sessid TEXT POINTERS b ADDR xxxxxxxx TEXT UNIT unitname J 29 rvsMVS Messages and Codes 5 rvs Messages DF1173P DF1175E DF1176P DF1190P DF1199P DF1191W DF1191W DF1191E DF1191E DF1192W This message is issued in case of a dynamic allocation error It will display the contents of the used SVC 99 parameter list allocation request block text pointer list and text units F sid acme sessid DELETE EXISTING FILE BECAUSE OF SPECIFIED EXPIRATION DATE A restart of a transmission receive direction will be initiated If there is specified an expiration date for this data set to be received a restart at the abended position will be impossible That s why the part of this file which was already received before the transmission abend occurred will be deleted F sid acme sessid OUTPUT DATASET ALREADY IN USE A data set is to be received but the output data set is just used by another task within the rvs monitor This situation should normally not occur One reason for this might be that fi
90. As a result of this situation the OFTP session will be terminated abnormally This error may occur if rvs receives an SFID protocol unit but for some reasons responds with an SFNA protocol unit If the remote station repeates this sequence without any retry time between the different attempts rvs will terminate the connection to avoid a loop situation DF9428E Z sid accm sessonid DECODE OF SFID FAILED rc reason 156 rvsMVS Messages and Codes 5 rvs Messages This message is issued by the Odette File Transfer Protocol task when an error occurs during decode of a received Start File Id SFID protocol unit In the message is shown the code xx that will be used in the corresponding Start File Negative Response SFNA protocol unit The following list describes the different reason codes 01 Invalid filename 02 Invalid destination 03 Invalid origin 04 Storage record format not supported 05 Maximum record length not supported 06 File size is too big 10 Invalid record count 11 Invalid byte count 12 Access method failure 13 Duplicate file 99 Unspecified reason DF9429P A sid accm sessonid SESSION REJECTED reason This message is issued by the Odette File Transfer Protocol task A request for establishing a session with station sid has been rejected reason may be one of the following conditions ISTATUS INACTIVE The stations entry for sid has been marked inactive but a connection with sid req
91. Client Task issues this message when an End to End Response EEID protocol unit is received but the EEID can not be associated with a previous file transfer The message shows the received data in the EEID protocol unit starting from the date information D sid sesid FTP message D sid sesid UNEXPECTED END OF FTP OUTPUT FILE D sid sesid FTP CONNECTION REJECTED D sid sesid FTP SESSION REJECTED D sid sesid TRANSMISSION CANCELED D sid sesid FTP FUNCTION ERROR D sid sesid VERIFY FTP RETURNCODE nnnn The FTP Client Task issues these messages by checking FTP output file Appropriate set of messages DF8860E DF8868E show corrected or not corrected flow FTP connection during transfer of rvsMVS FTP file If FTP returncode is equal 04 or 08 the FTP connection ended with error see rvs log messages D sid sesid UN ALLOC FAILED nnnn mm VOL volume DSN dsn The FTP Client Task issues this message when an error occurs during allocation or unallocation of a dataset In the message is shown the return code from the allocation request and the volume and dataset name of the file for which the error occurred D sid sesid OPEN FAILED FOR VOL volume DSN dsn The FTP Client Task issues this message when a dataset to be send or received could not be opened In the message is shown the volume and dataset name of the file for which OPEN error occurred D sid sesid SUCCESSFUL FILE TRANSFER direc
92. DP 73 DS 28 46 47 48 66 72 78 79 111 114 115 118 132 134 151 159 169 DSP 50 DX 55 PMSG 52 Trace 26 Dispatcher 82 83 85 86 87 88 89 Parameter 52 82 83 Dispatcher Task 82 FT Receive Control Task 120 FTP 9 10 26 27 73 74 119 120 121 122 123 124 125 128 129 130 131 132 134 135 146 162 FTP Driver Task 128 FTP Polling Task 125 Genaral Parameter List 35 LU 6 2 26 40 43 50 54 76 83 85 88 126 164 166 169 LU6 2 Control Task 164 Monitor 7 11 43 46 53 54 63 76 ODETTE FTP 146 Receive Dispatcher Task 92 Send Dispatcher 90 Parameter 90 Send Dispatcher Task 90 Station table 38 TCP 54 111 112 113 114 115 116 117 118 VTAM Control Task 137 VTAM Session Handler 171 X 25 Control Task 156 X25 35 40 49 50 51 52 54 151 175 179 180 194
93. ED This message is displayed in response to the operator command MSGOUT output of SYSWTO messages and Dumps allocated to the DD Names rvsDUMP and SYSUDUMP before monitor end Please refer to OPERATIONS MANUAL The message is displayed as first message in the splitted output DF3041I LOCAL SID sid CURRENT RELEASE x y MODIFICATION LEVEL nn The message displays the actual rvs software version after start of the rvs Monitor x denotes the release y denotes the subrelease and nn denotes the modification level within the subrelease This information is useful in case of problem determination The message is also displayed as response to the command DB In this case the own rvs station ID sid is additionally displayed DF3042W RECEIVE VOLUME EXCLUSIVE WITH UNIT PARAMETER INPUT IGNORED The rvs command VOLUME value has been entered During start of rvs the rvs start parameter VOLUME was not specified In this case it is not possible to introduce this parameter the specified command will be ignored See the description of the rvs startparameter VOLUME or the rvs command VOLUME for more information sna DF3043I CURRENT SOFTWARE DOES NOT INCLUDE x25 SUPPORT Bsc You wanted to start a component of rvsMVS which is not included in your rvs installation A list of the included components is displayed when you start the rvsMVS monitor see DF3046l DF3044I EXPIRATION DATE OF CURRENT SOFTWARE ddd yy T
94. ED FOR SELECTED CTCP This message is issued by the rvs X 25 CTCP task if the operator command A SID Cnn Nmm was entered In this case the specified partner number index is defined for the station but not for the specified CTCP This message is issued when the rvs X 25 CTCP task sends an outgoing call packet to a partner station with the specified X 25 number 168 rvsMVS Messages and Codes 5 rvs Messages DF9553P DF9554P DF9555P DF9557P DF9558E DF9559E DF9590P DF9590P DF9591P This message is issued by the rvs X 25 CTCP task when an virtual control block VCB has been found and no appropriate session control table SCT entry exists rvs will handle this problem and release the VCB entry This message is issued by the rvs X 25 CTCP task when an active ODETTE task has been detached This happens only in that case that the subtask dies not respond any more nn ODETTE TASK NOT RESPONDING WILL BE CANCELLED This message is issued by the rvs X 25 CTCP task when an ODETTE task is not responding nay longer In this case it will be detached nn INVALID BUFFER BUFFERADDRESS DETECTED BUFFER NOT RELEASED This message is issued by the rvs X 25 CTCP task when a buffers is to be released In this case an invalid buffer address has been detected and the buffer will not be released nn JES ALLOCATION PROBLEM This message is issued by the rvs X 25 CTCP task if the JES3 alloc problem has been
95. ERROR All other line errors f sid 111 TRANSMISSION TERMINATED DUE TO REMOTE ABNORMAL CONDITION At the remote station an error has occurred requiring the abort of the current transmission Message DF56141 usually follows f sid 111 dsname RESPONSE IGNORED During the normal termination phase of a transmission the receiving station sends the RESPONSE record rvs line protocol record This RESPONSE record is to be ignored because there is no fitting AS record with the data set name dsname in the control data set of the transmitting station Either the RESPONSE record has been generated with the wrong dsname by the receiving station or the control data set of the transmitting station is in error A 111 READY TO TRANSMIT The transmission can start Dial the desired station and press the data button A sid 111 TRANSMISSION ENDED The transmission of data with the corresponding station has terminated DF5621A follows if P sid or C sid was not entered previously f sid 111 INTERVENTION REQUIRED ENTER A COMMAND TO RETRY THE CONNECTION 105 rvsMVS Messages and Codes 5 rvs Messages DF5624E DF5625E DF5626P DF5628A DF5629P DF5630P DF5631P DF5632E DF5633E DF5634E The hardware connection between the control unit and the modem has been interrupted After elimination of the fault a station related command e g M sid or Q sid must be entered in order to restart the transmissio
96. FO90Axx Should not occur error Posted ECB not found This ABEND is coded in the program DF090Axx Should not occur error Error during LOSTTERM exit processing This ABEND is coded in the program DF090Axx Should not occur error Branch table overflow 15 rvsMVS Messages and Codes 3 rvs Abend Codes 908 916 990 991 992 993 994 996 997 1000 1001 1002 1003 1004 1010 1011 1012 38C 394 3DE 3DF 3E0 3E1 3E2 3E4 3E5 3E8 3E9 3EA 3EB 3EC 3F2 3F3 3F4 This ABEND is coded in the program DF908Bxx The load processing to fetch the module DFO80A00 failed This ABEND is coded in the program DFO90Axx Should not occur error The execution of the SHOWCB macro failed This ABEND is coded in the program DF099Axx Should not occur error An error occurred during establishing a rvs VTAM session OPENDST processing This ABEND is coded in the program DF099Axx Should not occur error An error occurred during OPENDST while processing a INQUIRE macro This ABEND is coded in the program DF099Axx Should not occur error Posted ECB not found in the multiple wait routine This ABEND is coded in the program DF099Axx A VTAM macro ended with failure This ABEND is coded in the program DF099Axx During start of a RPL request this RPL was still active This ABEND is coded in the program DF099Axx A RPL request has been posted but it could not b
97. FTP Server Task issues this message when during DFSMS function for a data set scratch locate catlg uncatlg or rename an error occurs In the message is shown the return code from the request and the volume not always and dataset name of the file for which the error occurred DF8586P D sid sesid VERIFY HD FILE RC nn FILE dsn The FTP Server Task issues this message when verification HFID record failed Shown is the HFID file name DF8598P D sid sesid KDUPDAT 88F xxxxxxxx TYP xx 128 rvsMVS Messages and Codes 5 rvs Messages DF8599P DF85A0P DF85A1P DF85A2P DF85A3P DF85A4P DF85A5P DF85A6P DF85A7P DF85A8P DF85A9P DF85BOP DF85B1P DF85B2P DF85B8P DF85B3P DF85B4P DF85B5P DF85B6P DF85B7P DF85BAP DF85BBP DF85BCP DF85BDP The FTP Server Task issues this message when verification HFID record failed Shown is the HFID file name The FTP Server Task issues this message List internal action of FTP Server task with KD control file For internal use only D sid sesid xxxxxxxx nnnnnn nnnnnn The FTP Server Task issues this message Show is the name of FTP Server Task subroutine that gets control For internal use only D sid sesid CS RECORD FOUND DSN dsname D sid sesid NO CS RECORD FOUND DSN dsname D sid sesid ORIGIN STATION KNOWN D sid sesid SENT DSN dsname D sid sesid MESSAGE REQUESTED D sid sesid EEIDDSN dsname D sid sesid
98. FTP Server Task message vvv specify version of FTP Server Task dd mm yy tt mm time of assembly aa bb cc time of last changes in the FTP Server Task DF8503E D sid sesid FTP SERVER ABEND CODE EP PSW The FTP Server Task issues this message when an abend occurs The message shows the system abend code the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done after all subtasks have been terminated DF8504I D sid sesid REGS 0 7 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXKXXXXX XXXXXXXK XXXXXXXX The FTP Server Task issues this message when an abend occurs The message shows the content of the registers 0 to 7 at the time of the abend DF8505I D sid sesid REGS 8 15 xxxxxxxx XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XKXXXXXX XXXXXXXK XXXXXXXX The FTP Server Task issues this message when an abend occurs The message shows the content of the registers 8 to 15 at the time of the abend DF8540P D sid sesid SERVER event The FTP Server Task issues this message when find appropriate FTP Server event The following list describes the different FTP Server events STOP OR CANCEL EVENT OPERATOR COMMAND EVENT NR FILE EVENT EE FILE EVENT XX FILE EVENT HD FILE EVENT For internal use only DF8543P D sid sesid RC nnnn HEX DFO88V KD RECORD BUILD The FTP Server Task issues this message when checking of HFID records ended with error
99. FTP jobs found The meaning of the parameters is xx FTP internal records type F2 rvsFTP Task generates this record before submitting the rvsFTP job send direction If this record is shown the rvsFTP job has not yet finished itself Must have examined if doesn t give problems executed this job e g JCL error s At necessity there is again by means of S sid command possibility to start transfer of this Dataset F3 rvsFTP Task generates this record during transmission send direction If this record is shown rvs waits on the Reply Dataset TD control Dataset Must have examined if doesn t give problems at transfer on the server side At necessity there is again by means of S sid command possibility to start transfer of this Dataset F5 rvsFTP Task generates this record during transmission send of Trailer dataset If this record is shown rvsFTP job has not finished itself NR control dataset has not generated still Must have examined if doesn t give problems executed this job e g JCL error s At necessity there is again by means of S sid command possibility to start transfer of this Dataset on the Client side SID station ID 77 rvsMVS Messages and Codes 5 rvs Messages DF4401E DF4402E DF4403E DF4404E DF4405E DF4406E DF4407E DF4408E DF4409E DF4410E DSN FTP control dataset name name of internal rvsFTP control dataset real dataset name nam
100. ID DATASET ALREADY EXISTS NO REPLACE 160 rvsMVS Messages and Codes 5 rvs Messages This message is issued to explain the cause of the duplicate file condition DF94651I F ORT ACCM SESSID MAXIMUM ERROR RETRIES REACHED FOR This message is issued by the Odette File Transfer Protocal task when the maximum allowed limit of transfer retries has been reached The OFTP session will be closed DF9466I F ORT ACCM SESSID WAITING FOR RDS TASK This message is issued when command DS has been entered and the OFTP task is currently waiting for an answer from the RDS task DF052X DF9469P S ORT ACCM SESSID message text FILENAME name This message is issued additionally to DF94111 to display the corresponding file name The following message text may occure IGNORED FIX EERP IN KD IGNORED LOAD PDS FILE IGNORED CODE TRANS READ IGNORED CODE TRANS WRT DF9470P file compression xxx This message is issued by the Odette File Transfer Protocol when the transfer starts It shows the current compression value for this file Possible values are NO no compression YES OFTP compression RVS rvs compression OFTP buffer online EXT rvs External Compression Feature DF9471P Z ORT ACCM SESSID LOG RECORD FOUND DSN name M DF9472P Z ORT ACCM SESSID LOG RECORD UPDAT DSN name M DF9474P Z ORT ACCM SESSID 2222222222222 2222222222222 PPPPPPPPPPPPPPPPPPPPPPPP DF9475P Z ORT ACCM SESSID 72727272727227222222222
101. ID protocol unit 15 Inact to active state This state is reached when a file transfer is to be started but before the actual data is transmitted 152 rvsMVS Messages and Codes 5 rvs Messages DF9404E DF9405E DF9406P DF9407E DF9408E DF9409T 01 Time out occurred during wait for SFID protocol unit response after SFID protocol unit was sent 02 An invalid File Protocol Unit was received in response to a sent SFID protocol unit 03 A protocol violation occurred when the response to a sent SFID protocol unit was received ie the received protocol unit was not an SFPA SFNA or ESID protocol unit 17 Active state In this state is the actual file transmission done 01 Time out occurred during wait for CDT after one or more data blocks had been sent 02 Time out occurred during wait for EFID protocol unit response after EFID protocol unit was sent 03 An invalid File Protocol Unit was received during wait for data or credit or response to EFID 04 A protocol violation occurred during data transfer as listener ie a protocol unit was received that was not an EFID or ESID protocol unit or a data unit 05 Time out occurred during wait for data as listener Z sid accm sessonid UNRECOGNIZED PROTOCOL UNIT RECEIVED STATE nn IC mm This message is issued by the Odette File Transfer Protocol task when an unrecognized protocol unit is received The state and information code values indicate in which situation the
102. It is not possible to enter a D sid command when a previous D sid command has not been completed Check for the outstanding reply of the previous D sid command by entering an invalid reply to the rvs monitor e g WRONG PARMRECORD TYP 01 IN CONTROL DATASET NO WORKING ALLOWED Severe error in control data set occurred Please contact your software distributor EXPIRATION DATE cpu ID NO USER TEST KEY gt 31 DAYS 58 rvsMVS Messages and Codes 5 rvs Messages PROD KEY gt 27 MONTHS PROD KEY NO NAME NUMBER BAY VERSION TEST KEY USER TEST KEY gt 13 MONTHS DF3053E INSTALLATION NOT COMPLETE RELEASE NUMBER b PRODUCT NAME PARAMETER M NOT DEFINED PARAMETER K R NOT DEFINED INCORRECT VERSION ALL MONITORS IN USE NOT FOUND SMF SVC LICENCE KEY OTHER J Severe error in installation the licence key is invalid or has expired Please contact your software distributor DF3054E License will expire in xxx days License key will expire in xxx days Please contact your software distributor DF3055I A sid XXXXX ACTIVATION REJECTED ISTATUS INACTIV ISTATUS INACTIVE has been specified for station entry sid Change this parameter to ISTATUS ACTIVE within the STATIONS table x 25 crcP DF3056P nn RE ACTIVATION OF rvs b SUBTASK STARTED tcp ip J The rvs X 25 CTCP subtask nn or the TCP IP controltask for
103. LU that originated the exit Exit Exit reason description TPEND RRO000 00 VTAM reason code for TPEND exit LOSTERM RRO000 00 VTAM reason code for LOSTERM exit RELREQ not available SCIP RPLCNTDF DC SC UNB TYPE from read only RPL DFASY RPLCNTDF DC SC from exit read only RPL NS NSPE RRSSSS US RR VTAM reason code SSSS _ sense US user sense byte 2 NS NOTFY RRSSSS US same as NSPE NS CLEAN RRO0000 00 same as NSPE 177 rvsMVS Messages and Codes 5 rvs Messages DF9723P DF9724P DF9725P DF9726P DF9727W DF9728W DF9729I DF9730I ACT recommended action 01 ignore processing is done in the exit 02 inhibit further sessions 03 close ACB PLU 2222222 RSN xxxxxx xx ACT LU CID This message is issued by the rvs APPC task manager routine The message is the same as the previous except for the exit reason being edited into character format in case of SCIP and DFASY exit types CNOS REQ FROM MODE LIMITS This message is issued by the rvs APPC task manager routine A CNOS request was received from the indicated partner LU In the message is shown the corresponding mode name and the session limits negotiated Also shown is whether the request was accepted or rejected A request is rejected if no station could be found for the parter mode combination This message is issued by the rvs APPC task manager routine A LOSS request was received
104. LUE IN LINEBUFER DETECTED The transmitting station specified an invalid length value in a data record The transmission of the data set is cancelled an rvs trace command T sid should be started to obtain error information in case of a later restart If the problem still exists in a later restart the software of the sending station does probably not work ok the trace should be passed to the producer of the sending software R sid mn BLOCKSIZE LRECL NOT PROVIDED The rvs header record sent by the transmitting station did not contain any value about record or block length of the data set R sid mn BLOCKSIZE LRECL LARGER THAN MAX BLOCKSIZE OF RECEIVING DISK The block length of the output data set exceeds the maximum track capacity of the used disk volume An automatic deblocking was not possible R sid mn REMOTE JOB dsname NOT AUTHORIZED PROCESSING NOT STARTED The data set dsname has been received from the remote station sid These data set should be submitted as a job but for the station sid there is no authorization to do this R sid mn 272277272222 2222 222222222 22922 2222 This message is issued by the SNA LU 0 Protocol task when a data set has been received One of the following actions and or errors have occurred after receiving DATASET RENAMED dsname With DFSMS the data set is received under a temporary data set name with timestamp After complete reception the data set has been renamed to its final name dsna
105. M DF1041I 2222222 This message will be displayed after the service program IDCAMS was called by rvs The message s contains the SYSPRINT output of IDCAMS DF1091I PROCESSING OF CODE TRANSLATION TABLES STARTED Reading of the internal and external code translation tables has been started See also DD statement TRNTABLES in rvs start job DF1098I PROCESSING OF CODE TRANSLATION TABLES COMPLETE Reading of the internal and external code translation tables has been finished See also DD statement TRNTABLES in rvs start job DF1099P AVAILABLE CODE TRANSLATION TABLES ARE DF1099P STDA2E STANDARD TABLE ASCII gt EBCDIC DF1099P STDE2A STANDARD TABLE EBCDIC gt ASCII DF1099P ODTA2E ODETTE TABLE ASCII gt EBCDIC DF1099P ODTE2A ODETTE TABLE EBCDIC gt ASCII DF1099P tabname List of names of the available codetranslation tables The first two tables are standard tables ASCII lt gt EBCDIC with German character sets ODTA2E and ODTE2A are the translation tables for OFTP transmission with FORMAT TEXT tabname is the first name of the external user defined translation tables See also DD statement TRNTABLES in rvs start job DF1171E F sid UN ALLOCATION ERROR xxxx yyyy FOR dsn An error occurred during allocation or unallocation of a data set DYNALLOC macro returned with errorcode xxxx and infocode yyyy The codes are described in OS VS2 MVS SPL Job Management DATASET ALLOCATED TO ANOTHER JOB REQUESTED UNIT NOT
106. METER This message is issued by the FTP Main task when an invalid parameter to a used command is detected command This message is issued by the FTP Main task when decode of command parameter s fails kkkkkk k UNEXPECTED END OF TASK kxe This message is issued by the FTP Main task when Client or Server task ended with error abended For internal use only KDUPDAT 89F 22777272727 TYP This message is issued by the FTP Main task List internal action of FTP Main task with KD control file For internal use only 3229299999797 7 77979999 9999999 See DF88Y3P FTP control file name This message is issued by the FTP Main task if FTP control file s is are found DATASET NOT RENAMED ENQUEUE ON SYSDSN FAILED This message is issued by the FTP Main task when enqueue on sysdsn failed rename error internal cod X 040B0426 9272229299 This message is issued by the FTP Main task trace routine Shown is the name of FTP Main task subroutine that gets control 141 rvsMVS Messages and Codes 5 rvs Messages For internal use only 142 rvsMVS Messages and Codes 5 rvs Messages Messages of the SNA LU6 0 Control Task DF9000I DF9001E DF9003I DF9004I DF9005I DF9006P DF9007E DF9008E DF9009E VTAM SUBTASK STARTED This message is a response to the command A rvsV It indicates that the rvs VTAM control task is successfully activated command I
107. NKNOWN and will be ignored A sid INVALID SESSION TYPE mn X xxxx REQUESTED SESSION REJECTED Via BIND request station sid tried to establish a session of type mn to rvs The session type mn is not defined in the sessions table entry for station sid CID cid UNKNOWN NO SESSION ENTRY ADDRESS During rvs initialization the rvs sessions tabele is dynamically updated with the cid The reason for this message is a rvs internal error A sid mn ATTACH FAILED RC xxxx The subtask which activates session mn could not be started The station sid could not be connected to rvs The ATTACH macro terminated with return code xxxx STARTED 144 rvsMVS Messages and Codes 5 rvs Messages DF9020I DF9021E DF9022I DF9023E DF9024I DF9025P DF9026P DF9027E f sid mn TRACE b lSTOPPED The rvs trace of session mn to station sid has been started stopped NOT ACTIVE f sid mn TRACE ALREADY ACTIVATED The rvs trace for session mn to station sid should be activated but was already active or the trace should be stopped but was not active A sid mn REJECTED TRY LATER The activation of the session mn to station sid has been rejected because there is already an active session mn to station sid Before starting a new session the old one must be terminated Message DF9023 indicates the previous activated session A sid mn IS PENDING A command A sid has
108. NVALID COMMAND This message is a response to an invalid command The command command has an invalid syntax ACB OPENED APPLID applid After starting the rvs VTAM control task the ACB with the application identifier applid has been sucessfully opened SETLOGON ISSUED After starting the rvs VTAM control task the SETLOGON macro has been successfully completed rvs VTAM CONTROL TASK READY The rvs control task has been started successfully Now it is possible to enter VTAM specific rvs commands in order to activate or to deactivate sessions with other stations or to get status information about existing sessions sc p LOGON EXIT ENTERED INSEXIT LOSTTERM J The Activation of a VTAM exit is indicated OPEN ACB FAILED APPLID applid RC xx ERROR x yy After starting the VTAM control task the ACB with the application name applid could not be opened To analyse the return code xx and the error code yy see Advanced Communications Function for VTAM Programming APPLID NOT STARTED The ACB could not be opened because the SYS1 VTAMLST data set contains no APPL statement for this application or this statement has not been activated SETLOGON FAILED RC xx yy FDBK zz After starting the VTAM control task the execution of the SETLOGON macro failed For a description of return code xx register 15 yy register 0 and feedback code zz see Advanced Communications Function for VTAM Programming 143
109. ON WITH REMOTE STATION NOT ESTABLISHED It has not been possible to establish synchronization with the remote station on a leased line The monitor repeats the attempt f sid 111 FILNAL STATION sid2 BUT NO VALID ENTRY IN 106 rvsMVS Messages and Codes 5 rvs Messages DF5635P DF5636P DF5637P DF5638P DF5640E DF56411 DF5642E DF5643E DF5644W STATIONS TABLE The station sid received a data set After receiving this data set should be transmitted to a third station with station sid2 but for the third station there is no valid entry in the stations table sid 111 i RECORD RECEIVED DSN dsname DSTIME time xf sid 111 i RECORD HAS BEEN SENT DSN dsnameDSTIME time The received or transmitted rvs protocol records will be noted in the printout wacks sid 111 xx TTDS RECEIVED lstxETx Since line control has been established the remote station has transmitted xx control character until now WACKS TTDS STXETX DUMMY record This fact indicats that the remote station is not able to transmit or receive data at this time but the remote station wants to keep line control sid NO RESERVED VOLUMES NEEDED This message appears if the TP task recognizes an interlock situation timeout may occur on a switched line The reason for this situation is not a RESERVED volume caused by another task f sid nnn TRANSMISSION TERMINATED BECAUSE OF INCOMPLETE CONNECTION PHASE The transmissio
110. P IP control task will terminate after this error TCP IP INITIALIZATION FAILED This message is issued by the rvs TCP IP task during initialization of the task An error occured during initialization the tcp ip control task will terminate after this error This message is preceeded by one or more other messages indicating the kind of the error XX TCP IP SUBTASK COULD NOT BE STARTED NOT ENOUGH MEMORY This message is issued by the rvs TCP IP task when activation of further subtask OFTP Task is rejected because of storage shortage Messages of the TCP IP line driver of rvsMVS for the TCP IP stack of Interlink DF8351I DF8352P DF83531 DF8354I This message is issued by the rvs TCP IP task when task initialization is complete The level of the program is shown This message is issued by the rvs TCP IP control task when task termination has started or is complete This message is issued by the rvs TCP IP task in response to a display DS command The message shows the level of the program 222222222 FAILED S RCHAAAAAAAA ECHAAAAAAAA This message is issued by the rvs TCP IP task when a TCP IP request fails The message shows the failing request the socket number for which the request was issued the return and the error code Remark For more information about the return and error codes refer to manual CISCO IOS for OS 390 Unprefixed Messages and Codes 121 rvsMVS Messages and Codes 5 rvs M
111. PDATE OF THE KD RECORD FAILED INITIAL READ OF THE KD RECORD FAILED Error of the control data set RVS KD in the program DF024A00 See also message DF2401E D sid INVALID REPLY REENTER COMMAND 46 rvsMVS Messages and Codes 5 rvs Messages An invalid reply has been entered enter correct reply according to the displayed message DF2510A D sid dsname VOL volume ENTER DEL OR NO OR END DF2510A D sid dsname QD yyddd QT hhmmsst ENTER DEL OR NO OR END After input of the D sid command the first entry for which the selection criteria are valid is indicated For send or receive entries the data set name and the volume number are displayed For end to end responses the data set name and the queuing date and time are displayed The following replies are possible DEL Entry is to be deleted NO The next entry is to be indicated END Request will be cancelled DF2520I D sid REQUESTED ENTRY DELETED The requested entry has been deleted after input of DEL in the response to DF2510A DF25251I D sid REQUESTED ENTRIES DELETED The requested entries have been deleted after input of DEL as response to DF2590A DF2530E D sid NO MORE ENTRIES FOUND No entry or no further entry after input of NO in response to DF2510A was found in the control data set The D sid command may have been incorrectly entered DF2540A D sid IS THE DATA SET TO BE SCRATCHED FROM DISK YES OR NO If the data set t
112. R name R ORT LOG ENTRY LG FOR name R ORT text Messages DF1198P until DF1199P are for possible error detection only They are not in effect for users purpose f sid 111 LINE I O ERROR DECERRST X xx During data traffic with station sid on BSC line Ill III denotes the subchannel address an O error has occurred xx denotes the error status flags as indicated within the BTAM control block DECB For a description of the error status flags see for example the IBM manual OS VS BTAM As a result of this error the line connection will be broken f sid 111 BTAM ERROR RECOVERY P X pp OPCD X oo TPCD X tt FLAGS X ff ERRST X ee CSWST X cccc SENSE X ss This message is written only to the rvs protocol not to console It indicates a failing BTAM I O during data traffic with station sid on BSC line Ill III denotes the subchannel address The error is recorded by the rvs error recovery routine for BTAM I O Depending on the kind of error s this routine tries to recover the error The result of the recovery may be continuation of the data traffic or break of line connection This message displays the following fields of the BTAM control block DECB For a detailed description of these fields see for example the IBM manual OS VS BTAM 31 rvsMVS Messages and Codes 5 rvs Messages DF1203E DF12311I DF12311I DF1232P P postcode of BTAM I O completion OPCD type of BTAM operation execute
113. RED STATE nn IC mm This message is issued by the Odette File Transfer Protocol task when a time out condition has occurred The Odette File Transfer Protocol defines a maximum time interval between the exchange of file protocol units If a file protocol unit is not received within the time interval the connection will be terminated The default value for the time interval is 10 minutes In the message is indicated when the time out occurred by the state and information code values The following state and information code values are defined State Code Description 12 Reset to inact state This state is reached when an outgoing call is made or an incoming call is received but before the Start Session Id SSID protocol units has been exchanged 01 Invalid SSRM protocol unit received 02 Invalid SSID protocol unit received 03 Time out occurred during wait for SSRM protocol unit 04 Time out occurred during wait for SSID protocol unit 14 this state a connection exists to the partner station but no file transfer is active 01 Invalid RTR protocol unit received in response to a sent EERP protocol unit 02 Time out occurred during wait for RTR protocol unit after EERP protocol unit was sent 03 Time out occurred during idle wait as listener 04 An invalid File Protocol Unit was received during idle wait as listener 05 A protocol violation occurred during idle wait as listener ie a protocol unit was received that was not an SFID EERP CD or ES
114. RSION 1234567890123456789012345678901234 DF5X01I RECEIV_DISP SUBTASK ENDED VERSION 1234567890123456789012345678901234 97 rvsMVS Messages and Codes 5 rvs Messages Start End message of Receive Dispatcher Task DF5X02P LIST OF RR ENTRIES CREATED REFRESHED This message is displayed after the list of resident receive entries in the monitors address space has been created during monitor start or refreshed DF5X03P addr1 addr2 flg RRsid dsn This message is displayed as a response to command DS RRLIST For every resident receive entry entry in the monitor internal list one message is displayed The message shows details about the monitor internal list of resident receive entries addr1 address of the next entry in the list addr2 address of the next section in the list flg flag indicating whether this entry contains valid data 08 or not 00 sid station id of the remote station dsn virtual dataset name DF5X03P END OF LIST OF RR ENTRIES This message marks the end of the display in response to command DS RRLIST DF5X09P LIST OF RECV REQUESTS REFRESHED Status message about refresh of the receive entry list DF5X10P NEW RECV DISP REQUESTS SELECTION Start of a new selection cycle for the receive entry list DF5X111 SDDDDDD STTTTTTT ASSID 12345678901234567890123456789012345678901234 This message one or more is a reply for DD command SDDDDDD day of queuing dataset STTITTTT t
115. SHED DUE TO LOCKED SERVER QUEUE s This message is issued by the rvs TCP IP task when data to be sent to the ODETTE file transfer protocol task was rejected due to a locked server queue ie The task was not ready to accept the request The message displays the related socket number This message is issued by the rvs TCP IP task when a connection is to be initiated This message displays IP address and port number of the remote station and of the own station as well OPTION ALL NOT SUPPORTED BY THIS COMMAND This message is issued by the rvs TCP IP task when the option ALL has been used for a command for which this option is not supported INVALID COMMAND PARAMETER This message is issued by the rvs TCP IP task when an invalid parameter is used with an issued command ODETTE TASK HAS BEEN POSTED S SID This message is issued by the rvs TCP IP task when the odette task is posted for termination The socket number and station is shown SPECIFIED STATION 2 27 2 22 2 22222222222 This message is issued by the TCP IP task when a command referring to a station is used Either the station could not be found the station was already active for activate command or 119 rvsMVS Messages and Codes 5 rvs Messages DF8329I DF8330P DF83311I DF8332E DF8333W DF8334P DF83351I DF8336E DF8337E the station is not active This message is also used to indicate a pending trace for a stat
116. TA SET EXECUTED BECAUSE OF VSAM FEEDBACK CODE 14 HEX An update of the rvs key dataset could not be executed because of VSAM feedback code 14 The code means a control intervall which is connected to the update processing is in exclusive control by another task This error situation is automaticly cleaned by an CLOSE OPEN of the control data set rvs repeats the faulty update USER ABEND 0640 REASON XX DEC OCCURED An error record occurred during access to the rvs key record A MODCB GENCB or SHOWCB macro could not be executed USER ABEND 0650 REASON XX DEC OCCURED 100 rvsMVS Messages and Codes 5 rvs Messages An error record occurred during access to the rvs key record A record was found in the key dataset that could not be decompressed Please use program DF 144A to find and delete the incorrect record s Message DF5U10E is for possible error detection only They are not in effect for users purpose DF5U10E INVALID RECORD XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX DF5501E f 111 111 OVERFLOW SWLIST TABLE TOO MANY STATIONS DEFINED FOR LINE 111 The rvs stations table contains too many station entries that use the same BSC line Ill III denotes the subchannel address of the line A maximum of 200 station entries may define the same line This message may be issued after activation of line Ill in this case the activated line control is terminated with user abend 551 DF5502E OPEN ERROR ON LINE 111 An activation
117. TSO userlD CONV EXT OK ERR Shows the status the conversion part status OK conversion has finished without errors ERR conversion has finished with errors conversion has finished with errors COMP EXT OK ERR Shows the status the compression part status OK compression has finished without errors ERR compression has finished with errors xxx compression has finished with errors SECR EXT OK ERR Shows the status the encoding part status OK encoding has finished without errors ERR encoding has finished with errors encoding has finished with errors TRACE nn Value of the internal trace parameter Comp Secr Parameter only for internal purposes JOB jobname Means after the termination of the transmission the job jobname is to be executed DF5002Q S sid QUEUE IS EMPTY The message appears as a reply to the command N sid Q and means that no send requests exist for this location DF5003I N sid NO TRANSMISSIONS DURING LAST 24 HOURS DF5003I N sid NO TRANSMISSIONS DURING LAST 7 DAYS The first message is output as a reply to the control data set queries N sid R name or N sid S name If no data sets have been received from the location concerned or if no data sets have been transmitted to this location during the last 24 hours If the name was specified 83 rvsMVS Messages and Codes 5 rvs Messages DF5005I DFS5006I DF5007I DF5008I DFS5009I DF5010
118. The APPCCMD RECEIVE was issued to read data but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information DF9736E APPCCMD DEALLOC FAILED FOR 22227222 RC xxxx SENSE xxxx This message is issued by the rvs APPC task manager routine The APPCCMD DEALLOC was issued to close a conversation with a partner node but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information DF9737E APPCCMD SEND CONF FLUSH FAILED FOR This message is issued by the rvs APPC task manager routine An APPCCMD SEND with CONFIRM or FLUSH option was issued in order to flush the send buffer and get an acknowledgement from the partner but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information DF9738I rvs APPC ACTIVE ACB CSS nnnn CCV nnnn FSS nnnn PCV nnnn 179 rvsMVS Messages and Codes 5 rvs Messages DF9739I DF9T740I DF9T7A1I DF9742E DF9744I DF9745I DF97461 This message is issued by the rvs APPC task in response to a Display DS LU62 or LU62 ALL command The message shows the ACB name used by the APPC task and the number of sessions CSS and conversations CCV currently active Also shown is the num
119. Use the GDG function if many files with same names are to be received within short time Make sure that there is enough space to allocate files to be received AON R sid mn RESTART COUNT OF SENDER EXCEEDS RESTART COUNT OF RECEIVER A rvs header record has been received In this record the restart count of the transmitting station exceeds the number of received A new transmission of this file is required R sid mn I O ERROR ON OUTPUT DATA SET NEW TRANSMISSION REQUIRED NO RESTART During output of data records an O error occurred A restart is not possible A new transmission is required R sid mn I O ERROR DURING RESTART POSITIONING NEW TRANSMISSION REQUIRED NO RESTART The received data set cannot be read for restart positioning a new transmission is required R sid mn RESTART COUNT EXCEEDS DATA SET RECORD COUNT In the header record the transmitting station specified a restart count which exceeds the number of received data records R sid mn dsname volume RESTARTS AT RECORD n Start message for the specified data set In case of a restart this message remains on screen until restart positioning of the data set has been completed R sid mn DELETING EXISTING FILE BECAUSE OF SPECIFIED EXPIRATION DATE A restart for a file with an expiration date is to be done But the extension of an existing file with expiration date requires operator intervention To avoid this the restart file will be deleted IDCAMS comman
120. VOLKSWAGEN T Systems mvs Release 04 02 02 Messages and Codes 2007 08 10 rvsMVS Messages and Codes This documentation is valid for rvsMVS release 02 05 and higher For rvsMVS the following documentation is provided rvsMVS Installation Manual English Installation of rvs Useful for System Programmers rvsMVS Benutzer Handbuch German Manual for rvs Users rvsMVS User Manual English Manual for rvs Users rvsMVS Operator Handbuch German Manual for rvs Operator rvsMVS Operation Manual English Manual for rvs Operator Distribution information will be given kindly T Systems gedas deutschland GmbH Silke Peigert Stephanie Begehold BU rvs Systems Pascalstr 11 D 10587 Berlin Tel 49 30 3997 1367 49 30 3997 1537 Fax 49 30 3997 1994 Email mailto Silke Peigert gedas de Email mailto Stephanie Begehold gedas de Technical information will be given kindly T Systems gedas deutschland GmbH BU rvs Systems Pascalstr 11 D 10587 Berlin Tel 49 30 3997 1777 Fax 49 30 3997 1994 Email mailto rvs service gedas de Copyright 2007 by Volkswagen AG T Systems gedas deutschland GmbH 2 rvsMVS Messages and Codes Contents Contents 1 Introduction 2 2 ae ee el 3 2 rvs User Codes ccs cin a ea 3 3 vS Abend COdes 2 ee 3 4 FYS Sens C0des 2 1 E a 3 4 1 Dynamic allocation errors uursrsnnnnnennnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn
121. VS Messages and Codes 5 rvs Messages DF3005I DF3006I DF3006I DF3006I DF3007I DF3008I DF3009I DF3010E DF3011E KEPT END CATLG b Transmission has terminated normally UNCATLG The executed disposition is being DELETED J indicated on the second position ABEND sss uuu the transmission has been aborted because of an error sss System Completion Code uuu User Completion Code rvs MONITOR ENDED The monitor ended normally after the command P rvs has been entered All RVSMVS LINES ARE INACTIVE Reply to command DS if no line is active acme SUBTASK ACTIVE BUT NOT READY Reply to command DS TCP or DS LU62 acme denotes the access method TCP IP or LU6 2 The message indicates that the control task for this component is active but not able to process commands from the rvs maintask For TCP IP this situation may occur if the IP address space is terminated abnormally In this situation the affected controltask should be stopped started again In some cases stop start or the rvs monitor may be required acme SUBTASK NOT ACTIVE Reply to command DS TCP or DS LU62 acme denotes the access method TCP IP or LU6 2 The message indicates that the control task for this component is not active It may be activated by entering the command A RVST or A RVSL is identical with DF3004I DF3007I is output upon termination of a transmission an
122. VTAM rv sX25 RMOP NOT READY The rvs VTAM X25 RMOP control module has been started but it is not yet ready to execute rvs VTAM X25 RMOP commands STILL ACTIVE The rvs VTAM X25 RMOP control module has already been started COMMAND IGNORED PREVIOUS rvs VTAM COMMAND NOT YET PROCESSED TRY LATER The rvs VTAM control module is temporarily unable to process the entered rvs VTAM command The reason is that the execution of the previously entered command is not yet complete f sid LINE nnn IS status The status may be WAITING FOR WORK The leased line nnn to station sid has been activated At present however no transmission is active When data sets are held see DF50011 an explicit transmit command S sid is necessary to restart the transmission PENDING The line control for line nnn and station sid has been started but is not yet ready For the reason see DF3036A f sid nnn REMOTE STATION IS NOT READY This line has probably not been activated at the remote station However there can also have been a modem or a line failure f sid nnn LINE CONTROL TERMINATED SYSTEM sss USER uuu The line control task for station sid and line nnn has terminated with system completion code sss or user code uuu see DF03011 VTAM nn TCP d nn X25 SUBTASK ENDED SYSTEM sss USER uu Lu62 RMOPJ The rvs VTAM TCP X25 LU62 RMOP subtask ended nn states the CTCP number X 25
123. XX XXXXXXXKX This message is issued by the FTP Main task when an abend occurs The message shows the content of the registers 8 to 15 at the time of abend DF8906I sid MAIN TASK ACTIVE nn DRIVER OR SERVER TASK S This message is issued by the FTP Main task in response to an DS command DF8907P sid TRACE FLAG IS ON OFF This message is issued by the FTP Main task in response to a T sid or O sid command DF8928P SPECIFIED STATION sid BUSY This message is issued by the FTP Main task when a command refering to a station is used The command cannot be honoured as all sessions for this station are active If this message often occurs increase the number of session value FTPSESS parameter DF8931P sid NOT USED COMMANDS WITH ALL PARAMETER 140 rvsMVS Messages and Codes 5 rvs Messages DF8 9321 DF8939I DF8940I DF8942E DF8970P DF8974P DF8977P DF8994P DF8995P DF8996P DF8999P This message is issued by the FTP Main task in response to an activate station command ACTIVATION REJECTED FTPMAX EXCEEDED This message is issued by the FTP Main task in response to an activate station command FTP ACTIVE NO ACTIVE SESSION FOR STATION FOUND This message is issued by the FTP Main task in response to a CANCEL C or STOP P FTP command FTP ACTIVE ACTIVE SESSION FOUND This message is issued by the FTP Main task in response to a CANCEL C or STOP P FTP command INVALID COMMAND PARA
124. Y FREE SPACE ON rvs LOG DATA SET This message occures if the rvs log data set contains less than 20 19 2 1 of free space The message indicates that program DF072A00 saving of control data set and log data set has to be started within the next time x SAVING OF KD AND rvs LOG DATA SET REQUIRED This message appears only in conjunction with message DF5402W F sid REQUEST FAILED BY USER EXIT message from exit length max 80 bytes Self explaining message passed by user exit RACF exit controlls the access to the control data set AUTOMATIC CLOSE FOR CONTROL DATA SET EXECUTED BECAUSE OF VSAM FEEDBACK CODE 14 HEX An update of the rvs control dataset could not be executed because of VSAM feedback code 14 The code means a control intervall which is connected to the update processing is in exclusive control by another task This error situation is automaticly cleaned by an CLOSE OPEN of the control data set rvs repeats the faulty update TIME USED FOR ENQ RESERVE nnn hh SEC TYPE OF REQUEST rr This message has been introduced for reasons of performance measurement It will be displayed if the difference of the time before issuing ENQ or RESERVE and after execution of DEQ done for serialization of the rvs Controldataset exceeds at least 2 seconds nnn denotes the time value in seconds hh denotes the value in 1 100 sec rr denotes the typy of request access to the rvs Controldataset 99
125. ZERO RETURNCODE OF INSTALLATION EXIT DFUX001 R sid ONLY INSTALLATION STANDARDS WILL BE USED TO RECEIVE dsname R sid RECEIVING OF dsname REJECTED BY DFUX001 See DF3735W DF3735E R sid RECEIVING OF dsname REJECTED BECAUSE OF NORELAIS dest A data set with name dsname shall be received from station sid For this station the parameter NORELAIS dest has been specified dest denotes the station ID to which routing is to be suppressed In this case receiving of the file with destination dest will be rejected R sid text 30 rvsMVS Messages and Codes 5 rvs Messages DF1193W DF1194E DF1195P DF1195P DF1196P DF1197P DF1198P DF1199P DF1199P DF1201E DF1202P This message precedes message DF1191W text is a message which is passed to rvs by the user exit R sid RECEIVING OF dsname REJECTED DUPLICATE FILE See DF3738E R sid RECEIVING OF dsname REJECTED ODETTE ID MISSING The ODETTE ID has not been specified by the sender The transmission is cancelled Make sure that the sender provides for an ODETTE ID that is not blank especially when using a relay station R ORT CALL OF DFUX001 INITIATED R ORT CALL OF DFUX001 COMPLETE R ORT text Messages DF1195P until DF1196P are for possible error detection only They are not in effect for users purpose R sid RESIDENT ENTRY RR FOR dsn IS USED While receiving the data set dsn a RR entry is used R ORT USER ENTRY UR FO
126. ack code yy and system sense code ssss see Advanced Communication Function for VTAM Programming NOT FOUND a logical unit this name is not defined NOT ACTIVE the logical unit is not active REJECTED the logical unit dis not accept the BIND request If there is more than one logical unit defined for station sid rvs tries to establish a session to the next logical unit R sid mn rplname ACTIVE AFTER SESSION TERMINATION During termination of a session was encountered that there is at least one VTAM RPL signed as active that means an earlier request send receive or session control request directed from rvs to VTAM could not be terminated by VTAM rplname indicates the RPL which is still active rplname may be one of the following names OPCRPL SNDRPL1 SNDRPL2 RECRPL or SESSRPL In case of the RPL could not signed as inactive in at least 10 minutes by VTAM the session task terminates with the rvs User Abend 995 R sid mn RPL ALREADY ACTIVE ON request The receive module ended but one RPL within this module is still active a VTAM macro did not yet complete R sid mn INVALID PASSWORD RECEIVED The password received from the remote station is not equal to the expected password specified within your stations table Session has been rejected R sid mn PASSWORD RECVED BUT NO EXCHANGE DEFINED A password has been received from the remote station but password exchange has not been defined 183 rvsMVS Me
127. acme nm 1 ee ee eee This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISPALL This message is issued by the dispatcher task trace routine Shown is the name of dispatcher task subroutine which gets control 93 rvsMVS Messages and Codes 5 rvs Messages Messages of the Send Dispatcher Task DF5M01I SEND_DISP SUBTASK STARTED VERSION 1234567890123456789012345678901234 DF5M01I SEND_DISP SUBTASK ENDED VERSION 1234567890123456789012345678901234 Start End message of dispatcher routine This program is started just after start of the rvs monitor For a description of the functions performed by this task see Installations Manual chapter 5 rvs Start parameter DSPTI and DSPTIW vvv version of Dispatcher dd mm yy tt mm time of assembly aa bb cc time of last changes in the Dispatcher DF5M11I SDDDDDD STTTTTTT SASSID 12345678901234567890123456789012345678901234 This message one or more is a reply for DD command SDDDDDD day of queuing dataset STTITTTT time of queuing dataset 123 data set name DF5M22P 123456789012345678901234567890123456789012345678901234567890 The following text may be First 54 characters of KD record kk k MAX NUMBER OF SDS TASK EXCEDED x kkk ATTACH FAILED xkk k DFO52N ATTACHED kkk SDS STOP xx kkk SDS CANCEL xxxx WAITING SDS TASK ACTIVE k k TASK ACTIVE
128. age is issued if internal trace modul is used see command T RVSX This message is for internal use only 170 rvsMVS Messages and Codes 5 rvs Messages Messages of the XOT Control Task DF9IOI1I DF9I02P DF9I03E DF9IOOW DF9I23W DF9I24E DF9I25W DF9I26E DF9I27W DF9I28W This message is issued by the rvs XOT CTCP task when task initialization is complete nn states the CTCP number LV denotes to the current program version of program DFO9S5I This message is issued by the rvs XOT CTCP task when task termination has started or is complete nn rvs XOT CTCP ABEND CODE EP PSW This message is issued by the rvs XOT CTCP task when an abend occurs The message shows the system abend code the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done after all subtasks has been terminated nn SESSION START REJECT NO VIRTUAL CIRCUITS AVAILABLE This message is issued by the rvs XOT CTCP task in response to an operator Activate station command if no resources no sessions are available to handle a call request nn SEND DATA FLUSHED DUE TO LOCKED SERVER QUEUE This message is issued by the rvs XOT CTCP task when data to be sent to the Odette File Transfer Protocol task was rejected due to a locked server queue ie the task was not ready to accept the request In the message is indicated the task name nn INVALID COMMAND
129. ame D sid sesid MESSAGE REQUESTED D sid sesid EEIDDSN dsname D sid sesid EEIDORIG odette id of sender of EEID D sid sesid EEIDDEST odette id of recipient of EEID D sid sesid EEIDDATE date EEIDTIME time The FTP Client Task issues these messages when an error concerning a received end to end response has occurred They are intentionally issued for error detection For internal use only D sid sesid KDRECTYP KDREMOTE KDNEXT KDSTATUS nn D sid sesid KDDSN dsn name D sid sesid KDREADYD nnnnnnn KDREADYT nnnnnnn D sid sesid KDSTARTD nnnnnnn KDSTARTT nnnnnnn D sid sesid KDREC kdrecord D sid sesid D sid sesid D sid sesid D sid sesid D sid sesid KEY KDRECTYP KDREMOTE KDNEXT KDSTATUS nn KEY KDDSN dsn name KEY KDREADYD nnnnnnn KDREADYT nnnnnnn KEY KDSTARTD nnnnnnn KDSTARTT nnnnnnn KEY KDREC kdrecord FH The FTP Client Task issues these messages Show contents of KD file record For internal use only D sid sesid RE SET STLASTOK FLAG SID sid The FTP Client Task issues this message For internal use only R sid NONZERO RETURNCODE OF INSTALLATION EXIT DFUX001 R sid ONLY INSTALLATION STANDARDS WILL BE USED TO RECEIVE dsname R sid RECEIVING OF dsname REJECTED BY DFUX001 See DF3735W DF3735E R sid text This message precedes message DF88V1W text is a message that is passed to RVS by the user exit R sid RECEIVING OF
130. ame of the file DF5SN37I D name NOT CATALOGED TRANSMISSION CANCELLED DF5N38I D name COMP SECR INPUT FILE DF5N40P D DRIVER name Messages DF5N371 until DF5N40P are for possible error detection only They are not in effect for users purpose DF5N61P D 2 7 7 77 7 7 7 7 7 77 7 777 7 7 7 7 7777777777777777777777777x The following text may be ATTACH DF310A RC NOT ZERO Operator request gt CANCEL OPERATOR REQUEST gt 2ND STOP gt EXIT Operator request gt STOP input file not found key error security rc attach not zero Status messages of the Service Provider Task Send Dispatcher These messages are for possible error detection only They are not in effect for users purpose DF5N65P D 777772 77 cccccccc Return code message for access to the Security Key data Set with 2222222222222 RETURN CODE PUB KEY or RETURN CODE PRV KEY cccccccc VSAM return code and program return code This message is for possible error detection only It is not in effect for users purpose DF5N66P D PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP Internal file names used by the Service Provider Task Protocol message only This message is for possible error detection only It is not in effect for users purpose 95 rvsMVS Messages and Codes 5 rvs Messages DF5N67P DF5N68P DF5N69P DF5N71P DF5N72P DF5N80P DF5N99P D 3399999999
131. anager routine when a session start was successful with partner sid The message also shows the partner LU name and the used mode name DF9715E APPCCMD DACTSESS FAILED FOR 2 2 2 RC xxxx SENSE xxxx This message is issued by the rvs APPC task manager routine A VTAM APPCCMD DACTSESS was issued to reject a new session with the partner indicated in the message but the request failed In the message the VTAM return and sense codes for the failing request are shown Refer to VTAM programming manual for further information DF9716I SESSION REJECT FOR LU 77 772 72 2 MODE REASON This message is issued by the rvs APPC task manager routine when a session start request has been received The request to start a session is rejected due to the reason indicated in the message The message also shows the qualified network name of the partner and the mode used 176 rvsMVS Messages and Codes 5 rvs Messages DF9717W DF9718E DF9719P DF9720P DF9721P DF9722P This message is issued by the rvs APPC task manager routine A VTAM APPCCMD CNOS request was issued to change the session limits to a partner node but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information VTAM REQUEST FAILED REQ REASON SENSE This message is issued by the rvs APPC task manager when a VTAM request fails during request co
132. as occurred during data output No restart is possible and a new transmission is required An attempt will be made to utilize another volume R sid I O ERROR DURING RESTART POSITIONING NEW TRANSMISSION REQUIRED NO RESTART The data set already received cannot be read because of a read error A new transmission is required R sid RESTART COUNT EXCEEDS DATA SET BLOCK COUNT RETRANSMISSION WILL BE STARTED WITH LOWER COUNT The number of blocks received is lower than the specified restart count The transmission can be restarted by means of the operator command R sid 64 rvsMVS Messages and Codes 5 rvs Messages DF35131 DF3514E DF3515E DF3516P DF3517E DF3518W DF3518W DF3519W STARTING R sid dsname volume RESTARTING ON BLOCK nnn The start restart of reception of the data set dsname on volume volume takes place In case of a restart the restart point block nnn or record nnn is displayed The message remains displayed until the data set is positioned at restart point R sid INVALID BUFFER TYPE t RECEIVED BUFFER IGNORED A line block with invalid type t has been received This block is to be ignored and the transmission will be continued R sid EXPECTED BLOCKNUMBER IS nnnn RECEIVED BLOCKNUMBER IS mmmm An error has been detected in the block sequence check Instead of the expected block nnnn block mmmm was received A restart is required al a2 b1 b2 c1 c2 For
133. ask checking of HFID record Invalid syntax A data set is to be transmitted via rvsMVS FTP FTP Server Task checking of HFID record Invalid origin A data et is to be transmitted via rvsMVS FTP FTP Server Task checking of HFID record Invalid destination A data set is to be transmitted via rvsMVS FTP FTP Server Task checking of HFID record maximal length of record not supported A data set is to be transmitted via rvsMVS FTP FTP Server Task checking of HFID record data set already catalogued A data set is to be transmitted via rvsMVS FTP FTP Server Task checking of HFID record unspecified reason 9 rvsMVS Messages and Codes 2 rvs User Codes 188 192 196 200 201 202 203 204 205 206 207 208 209 210 211 212 OBC 0CO 004 0C8 0C9 OCA OCB 0CC 0CD OCE OCF 0DO 0D1 0D2 0D3 0D4 A data set is to be transmitted via rvsMVS FTP File open error A data set is to be transmitted via rvsMVS FTP Allocations control file s error A file is to be sent using the Odette File Transfer Protocol OFTP The local own station has initiated the connection to the remote station But sending of the file is not possible because the remote station does not accept to receive files receive capability not indicated whithin SSID The send request is cancelled when after this error has occured The name of the file which was sent is invalid The destinat
134. at1 DSCB bb returncode reg 15 of volume allocation ccccdynamic allocation error reason code volume allocation dddd dynamic allocation error info code volume allocation ee returncode reg 15 of obtain macro read format3 DSCB During extension of the existing file the following codes are used ff returncode reg 15 of new file allocation 9999 dynamic allocation error reason code new file allocation hhhh dynamic allocation error info code new file allocation ii returncode reg 15 of scratch macro old file jj scratch status code old file kk returncode reg 15 of rename macro ll rename status code mm returncode reg 15 of scratch macro new file nn scratch status code new file R sid REPLACE FUNCTION ALLOCATED SPACE n REQ SPACE m BLOCKS 48 rvsMVS Messages and Codes 5 rvs Messages DF2800I DF3000I DF3001A DF3002E DF3004I During reception of a file an already existing data set with the same name is to be replaced replace function During start of reception rvs checks whether the already existing file has sufficient space to store the file to be received This message displays the space allocated to the existing file n and the space required for the file to be received m in units of data set blocks JOB jobname STARTED TO PROCESS dsname The data set dsname is processed from the job jobname e Tapes to be transmitted are to be converted to disk Received disk d
135. ata sets are converted to tape if output is to be placed on tape Received lists are to be written to SYSOUT Received jobs have been started directly User jobs are started for processing of the data if indicated in the resident receive record in the control data set rvs MONITOR STARTED DAY yy ddd tt mm TIME hh mm DUR 999min Starting message of rvs Monitor with date yy year ddd machine date tt current day of the month mm month and start time hh hours mm minutes The message can be requested by operator command DB at any time Then 999 shows the duration of rvsMVS rvs OC READY If this message appears the rvs monitor is ready to accept rvs commands INVALID REPLY REENTER COMMAND The command previously entered is formally incorrect f sid 111 dsname nnn BL VOL volume status Status report of a BTAM line as reply to the command DS Display Status sid remote station ID WW line subchannel number dsname name of the data set which is just transmitted nnn number of blocks transmitted volume volume number and status status information The following status information may be displayed status meaning STARTING Transmission is just starting or restarting ACTIVE The transmission is active zz The transmission is active zz of the data set volume has already been transmitted CANCELLED The transmission is just being cancelled 49 rvsM
136. ates that load of the PDS has successfully completed volume denotes the disk volume number onto which the loaded PDS has been stored mn denotes the session SNA or the line address BSC which was used for receiption of this file DF6102E R sid mn DATASET dsname ALREADY EXISTS ON VOLUME volume A dataset has been received from station sid The received dataset is an unloaded PDS which must be loaded again rvs cannot load the received PDS onto the specified disk volume volume because a dataset with the same name already exists on this volume The transmission will be terminated abnormally This error should normally not occur because rvs tries loading of the PDS a second time with modified dsname before this message is issued See rvsMVS User s Manual Appendix for a description of PDS transfer mn denotes the session SNA or the line address BSC which was used for receiption of this file DF6103E R sid mn VOLUME volume NOT MOUNTED A dataset has been received from station sid The received dataset is an unloaded PDS which must be loaded again rvs cannot load the received PDS onto the specified disk volume volume because this volume is not mounted or an incorrect volume number has been specified for example within a resident receive entry The transmission will be terminated abnormally See rvsMVS Installations Manual Appendix for a description of PDS transfer mn denotes the session SNA or the line address BSC
137. ation not active backup dataset has already been comletely transmitted for other DD commands prioriy value of dataset specify or default external KD dataset only DD sid E command serialisation of sending datasets external KD dataset only DD sid E command serialisation is on serialisation is off for active entry for used entry transmission in progress for completed entry transmission is finish is displayed if end of internal KD dataset is achieved is displayed if end of external KD dataset is achieved is displayed if internal KD dataset is empty is displayed if external KD dataset is empty is displayed if DD command has syntax error 88 rvsMVS Messages and Codes 5 rvs Messages DF5212P DF5213P DF5214P DF5216P DF52181 DF52191 Message g _ is displayed if sid name was not found in stations table Message h is displayed if sid name exist in stations table but DD command has syntax error Message i is displayed if file name is incorrect for example wild card convention is not keep Message j is displayed if for specific request no entry exist in internal KD dataset Message k is displayed if for specific request no entry exist in external KD dataset S sid acme nm DISPATCHER HAS BEEN POSTED POSTCODE XX This message appears only within the rvs protocol It indicates the communication between different subtasks send session mn for
138. ation to transmit the data set dsname to station sid As a result the status of the transmission request specified in an entry of the control data set will be changed to the HOLD Status immediately For a description of this exit see Installations Manual Appendix A S sid mn text This message appears if the exit DFUX001 terminates with a return code of 8 text is a message of equal or less 80 characters which is passed to rvs by the exit DFUX001 S sid mn ENQ USE RETURNCODE xx DSN dsname The execution of ENQ DEQ macros is listed on printout During selection of a data set for transmission to station sid rvs checks whether the selected data set is just sent on another line or session or not This is done to avoid parallel transmission of the same data set to the same station S sid mn DEQ HAVE RETURNCODE xx DSN dsname See description of message DF1603P 36 rvsMVS Messages and Codes 5 rvs Messages Messages of Initialization of GENERAL PARAMETER LIST DF1900I PROCESSING OF START PARAMETERS STARTED This message is displayed when rvs begins processing of the rvs start parameters specified in rvs TABLES CNTL DF1901I CONTROL STATEMENT text This message displays the rvs start parameters specified in rvs TABLES CNTL It is possible to enter lines with a maximum of 72 bytes to specify the rvs start parameters For a description of these parameters see rvsMVS Installations Manual cha
139. be received by station sid The installed user exit DFUX001 supplies a nonzero return code The receiving of the data set is to be continued but every specification how to control or how to process the data set after receiving is to be suppressed Especially after receiving no user job is to be started by rvs DF3735E R sid mn RECEIVING OF dsname REJECTED BY DFUX001 A data set with name dsname shall be received from station sid but the installation exit DFUX001 which is executed during start of transmission ended with returncode 12 This means reception of the file is to be rejected by rvs The reason for this must be detected by the people who are responsible for the local rvs installation The file cannot be received until the exit DFUX001 has been changed DF3736E R sid text This message precedes the message DF3525W text is a message which is passed to rvs by the user exit DF3738E R sid mn RECEIVING OF dsname REJECTED DUPLICATE FILE The data set dsname shall be received from station sid During start of this transmission rvs detected that e the file to be received is to be cataloged after reception e a cataloged data set with the same name is already existing if the rename function is used the data set with the new name not with name dsname is already existing e the GDG function for this file has not been specified e a replace request for this file has not been specified As a result of these conditio
140. been entered but starting of the subtask which activates session mn to station sid is not yet complete a module could not be loaded from disk Reason The requested module cannot be loaded from the rvs load library reserved by another job or the requested module is not in the rvs load library Action Stop the request by entering P sid mn The name of the requested module may be listed by entering the command X sid S A ALL VTAM TERMINATED WITH ERROR Activating of all sessions which are marked to be activated see stations table if command A ALL is entered terminated with or without errors A sid mn NSHEADER hhhhhh request CV xxxx REASON rr SENSE ssssssss This message indicates that the NSEXIT of the rvs VTAM control task has been activated The contents of the VTAM request unit will be analyzed and listed hhhhhh the request header requestthe type of request CLEANUP NOTIFY or NSPE XxXxx the control vector key rr the reason code and sense information For a description of these fields see Advanced Communications Function for VTAM Programming SESSION NOT IDENTIFIED CID cid NETWNAMES lunames The session identified by cid has not been found lunames identifies the logical units of the VTAM network The reason for this message is a rvs internal error SESSION TABLE MISSING 145 rvsMVS Messages and Codes 5 rvs Messages The command A rvsVTAM has been entered
141. ber of unused sessions FSS and the pending conversations local attached driver subtask PCV SID P LU MODE CURS nnn MAXS nnn CONV nnn F xx SESL xxxxxxxxxxxxxx This message is issued by the rvs APPC task in response to a Display DS LU62 ANT command The message shows an entry in the Node Table In the message is shown the station id the priority used and the associated LU name and Mode name the current number of sessions the maximum allowed number of sessions and the current number of conversations using this LU Mode conbination Also shown is the current value of the session limit structure Note that the maximum number of sessions is twice the value specified for the station in rvs parmlib This is because each file transfer session requires two APPC sessions This message is issued by the rvs APPC task in response to a Display DS LU62 command The message shows information for an APPC Conversation Driver with the priority p In the message is shown d the transfer direction S send R receive sid the partner station id int_cid the internal conversation id created by the LU62 control task sti st2 state informations and the LU Mode name combination used for the APPC conversations TYP SYL PGM 2 TRACE This message is issued by the rvs APPC task in response to a Display DS LU62 ALL command The message shows information for an APPC Conversation Driver In the message is shown t
142. case the job submit will be rejected by rvs DF5818E JOB SUBMIT INITIALIZATION FAILED CREATION ACB RPL Error message in case of failed initialization of job submit function of rvs The job submit function of rvs cannot be used if this error has occured during start of rvs DF5819I MAX a USE b INS c SUB d RES e T1 t1 T2 t2 This message is displayed as a response to command DS JDSLIST ALL It shows some values concerning the jobdataset cache a maximum number of datasets within cache list b number of jobdatasets currently included in cache list c total number of inserts of jobdatasets into cache list since start of monitor d total number of job submits since start of monitor e number of executed reset commands for cache list t1 time of first job submit since start of monitor 110 rvsMVS Messages and Codes 5 rvs Messages t2 time of first removal of a jobdataset from cache list since start of monitor t1 and t2 denote the time interval backward from the current time the format is dd hh mm days hours minutes DF5820I DSN name CNT n T3 t3 T4 t4 This message is displayed as a response to command DS JDSLIST ALL The message is displayed for each jobdataset currently included in the cache list name dataset name of the jobdataset n number of job submits from this jobdataset since last insert of this dataset into the cache list t3 time when the jobdataset has been inserted la
143. cataloged The action failed xx denotes the return code hex of the SCRATCH CATALOG macro The status code yy hex is only issued by the SCRATCH macro For a further description of these codes refer to the IBM manuals which describe the scratch or catalog macro F sid CREATION OF SEND REQUEST FAILED F sid dsn NOT QUEUED TO STATION xxx A received data set dsn should be automatically passed by to a final station xxx but could not be queued for sending R sid mn 77777777777777777777777777777 This message is issued by the Odette File Transfer Protocol task when a data set has been received One of the following actions and or errors have occurred after receiving DATASET RENAMED dsname With DFSMS the data set is received under a temporary data set name with timestamp After complete reception the data set has been renamed to its final name dsname DATASET NOT CATALOGED xx The data set could not be cataloged after receiving For the information reason code xx see MVS ESA Authorized Assembler Programming Guide DATASET NOT SCRATCHED RC xxxx xxxxxxxx dsname The temporary data set could not be cataloged after start of reception For this reason the already allocated data set is to be scratched which did not end successfully For return and diagnosis codes xxxx xxxxxxxx see DFSMS MVS Diagnosis Reference 33 rvsMVS Messages and Codes 5 rvs Messages DF1244P DF1245P DF1246P DF1249P DF1411P DF
144. ceived The length of the calling DTE number is equal to zero 167 rvsMVS Messages and Codes 5 rvs Messages DF9543P DF9544P DF9545P DF9546P DF9547P DF9548P DF9549P DF9550E DF9551E DF95521 This message is issued by the rvs X 25 CTCP task when an X 25 clear packet has been sent to the remote station This message is issued by the rvs X 25 CTCP task when the ODETTE task has been posted for termination This message is issued by the rvs X 25 CTCP task when the ODETTE task has been detached after termination posted but a corresponding request has not been found nn PACKET SIZE AND WINDOW SIZE HAVE BEEN NEGOTIATED This message is issued by the rvs X 25 CTCP task when an x 25 call packet has been received and flow control parameters have been negotiated nn CALL CONFIRMATION SENT This message is issued by the rvs X 25 CTCP task when an x 25 call confirmation packet is sent The call confirmation is sent in response to a previously received x 25 call request nn ODETTE TASK EOT ECB POSTED SESSION This message is issued by the rvs X 25 CTCP task when the ODETTE task EOT ECB has been posted nn SPECIFIED PARTNER NUMBER INDEX mm NOT DEFINED This message is issued by the rvs X 25 CTCP task if the operator command A SID Cnn Nmm was entered and the specified partner number index mm is not defined in station table entry nn SPECIFIED PARTNER NUMBER INDEX mm NOT DEFIN
145. d BTAM macro TPCD tp operation code FLAGS status flags ERRST error status flags CSWST status bits from the CSW channel status word for the last CCW channel command word that was executed SENSE sense information f sid 111 BTAM I O ERROR CHANNEL STATUS status A BTAM I O ERROR has occurred during data traffic with station sid on BSC line III II denotes the subchannel address The error is recorded by the rvs error recovery routine for BTAM I O status may be one of the following values obtained from status bits from the CSW channel status word for the last CCW channel command word that was executed CHANNEL CONTROL CHECK INTERFACE CONTROL CHECK CHANNEL DATA CHECK ATTENTION STATUS MODIFIER CONTROL UNIT END BUSY UNIT CHECK CHAINING CHECK PROGRAM CHECK PROTECTION CHECK UNIT EXCEPTION INCORRECT LENGTH In case of a UNIT CHECK one of the following additional error information is displayed within this message obtained from sense information field of DECB EQUIPMENT CHECK LOST DATA TIMEOUT INTERVENTION REQUIRED BUS OUT DATA CHECK OVERRUN COMMAND REJECT PROCESSING OF COMMAND cmd STARTED nnnnn PROCESSING OF COMMAND cmd ENDED nnnnn Indication that the specified command cma is processed Start and end of processing for the following commands cmd is displayed Y STATIONS dump of the incore rvs stations table Y SESSIONS dump
146. d DETETE dsn PURGE and the transmission will be cancelled The file then will be transmitted again with the next restart attempt R sid mn EXPECTED LINE BLOCK NUMBER IS nnnn RECEIVED LINE BLOCK NUMBER IS mmmm An error has been detected within the sequence of transmitted line blocks R sid mn al a2 bl b2 The following counters are listed after receiving a data set al number of the received data records a2 number of data records transmitted by the remote station b1 number of the received characters 71 rvsMVS Messages and Codes 5 rvs Messages DF3717E DF3718E DF3719P DF3720E DF3721E DF3722E DF3723E DF3724P b2 number of characters transmitted by the remote station R sid mn REQ SPACE n BLOCKS NOT AVAILABLE Additional information to DF3702E The output data set could be allocated because the required space of n BLOCKS was not available Normally this message occurs only if the data set shall be directed to a specified volume R sid mn LINE BLOCK LENGTH nnnnn LARGER THAN RECEIVED BUFFER LENGTH mmmmm An error was detected in the format of the received line buffer The line buffer length specified in the two first bytes of the line buffer is not equal to the number of the received bytes R sid mn ADDRESS ALRBPTR xxxxxxxx If an error occurs during allocation of a data set the dynamic allocation control blocks are listed in hexadecimal code R sid mn INCONSISTENT LENGTH VA
147. d IGNOREDU The parameter is X 25 specific but the station is not defined for X 25 access method lt gt X25 ERROR FTPHNAME PARAMETER IS MISSING gt ENTRY FOR SID IGNORED For using the FTP component the FTPHNAME parameter is mandatory 42 rvsMVS Messages and Codes 5 rvs Messages DF2232E DF2233E DF2234E DF2235E DF2237P DF2238W DF2239W DF2240W DF2241W DF22421 ERROR FTPUID PARAMETER IS MISSING gt ENTRY FOR SID IGNORED For using the FTP component the FTPUID parameter is mandatory ERROR FTPPREF PARAMETER IS MISSING gt ENTRY FOR SID IGNORED For using the FTP component the FTPPREF parameter is mandatory ERROR TOO MANY STATION TABLE ENTRIES YOUR LICENCE ALLOWS ONLY ENTRIES gt rvsMVS INSTALLATION NOT COMPLETE The current licence doesn t cover the number of stations rvsMVS does not work ERROR FTPPASS PARAMETER IS MISSING gt ENTRY FOR SID IGNORED For using the FTP component the FTPPASS parameter is mandatory REFRESH OF KD STATIONS RECORDS ALREADY ACTIVE NOT EXECUTED The command REFR STAT is already active The next command REFR STAT ignored WARNING GZIP COMPRESSION ONLY SUPPORTED FOR ACCESS METHODS X25 LU62 TCP IGNORED FOR SID XXX The GZIP compression parameter COMPRESS GZIP found in station entry for SID xxx but the GZIP compression is available only for access method X25 LU62 and TCPIP The parameter is ignored
148. d authorization ALTER This ABEND is coded in the program DF054Xxx The rvs USERLOG Data Set is full This ABEND is coded in the program DF054Xxx The installation exit DFUX001 ended with a nonzero return code This ABEND is coded in the program DF054Xxx An error occurred during access to the rvs user record A record was found in the control data set that could not be de compressed This ABEND is coded in the program DFO76Axx Invalid internal PARM length Should not occur error This ABEND is coded in the program DF076Axx An invalid keyword has been specified in the PARM string This ABEND is coded in the program DFO76Axx No entry specified in PARM string This ABEND is coded in the program DF076Axx Invalid data set name specification 14 rvsMVS Messages and Codes 3 rvs Abend Codes 765 766 771 772 773 774 840 845 846 850 901 902 904 905 2FD 2FE 303 304 305 306 348 34D 34E 352 385 386 388 389 This ABEND is coded in the program DF076Axx Invalid station id specification This ABEND is coded in the program DF076Axx Invalid record type specification This ABEND is coded in the program DF077Cxx The data set assigned to the SYSPRINT DD statement could not be opened This ABEND is coded in the program DF077Cxx The load of the module DF067A was not successful DF067A contains the names of the data sets which are to be allocated
149. d if internal trace modul is used see command T RVSX The name of XOT Task subroutine that gets control is shown This message is for internal use only nn 2222222 VCB CONID SESSION SID The XOT Task issues this message This message is issued if internal trace modul is used see command T RVSX This message is for internal use only 174 rvsMVS Messages and Codes 5 rvs Messages Messages of the SNA LU6 2 Control Task DF9701I rvs APPC INITIALIZATION COMPLETE This message is issued by the rvs APPC task when initialization is complete DF9702I rvs APPC TERMINATION This message is issued by the rvs APPC task when task termination has started or is complete DF9703E rvs APPC ABEND CODE EP PSW This message is issued by the rvs APPC task when an abend occurs The message shows the system abend code the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done after all subtasks have been terminated DF9704I REGS 0 7 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX KXXXXXXX XXXXXXXX XXXXXXXK XXXXXXXX This message is issued by the rvs APPC task when an abend occurs The message shows the content of the registers 0 to 7 at the time of abend DF9705I REGS 8 15 xxxxxxxx XXXXXXXX XXXXXXXX XXXXXXXX KXXXXXXX XXXXXXXX XXXXXXXK XXXXXXXX This message is issued by the rvs APPC task when an abend occurs The message shows the content of t
150. d mn TIME hhmmssth event Display of internal trace data for session mn to station sid This message is displayed if the command U sid has been entered or if the session has terminated abnormaly event denotes the type of event which has occurred hhmmssth is the timestamp of the time when the event has occurred The following events are recorded in the internal trace VTAM REQUEST rpl based VTAM request Additional information type of request VTAM Macro returncode and feedback code of the request synchron or asynchron request complete or incomplete request definite response required or not STOP REQUEST stop request stop command has been detected CANC REQUEST cancel request cancel command has been detected SUBTASK ENDED normal end of the session subtask SUBTASK ABEND abnormal end of the session subtask LOSTTERM EXIT the lostterm exit has been scheduled for this session Additional the reason code is displayed SCIP EXIT the scip exit has been scheduled for this session Additional information DFC SC codes such as BIND REQUEST UNBIND REQUEST and others LOGON EXIT the logon exit has been scheduled NSEXIT the nsexit has been scheduled for this session Additional information NS RU CLEANUP NOTIFY or NSPE WAIT FOR REQ a VTAM request has been issued but the request has not completed 146 rvsMVS Messages and Codes 5 rvs Messages DF9031W DF9032W DF9071E DF9081I DF9082I DF9083I DF
151. d remains on the display for the duration specified in the HOLD interval DESC 2 TRACE xxx This message occurs if the command TRACE is entered For description of parameter xxx see rvsMVS Operations Manual f sid xxx READY TO TRANSMIT The modem is waiting for the data link to be made dial switch modem to data INVALID STATION ID sid ENTERED A station related command with an invalid station identifier sid has been entered INVALID LINE nnn FOR STATION sid 50 rvsMVS Messages and Codes 5 rvs Messages A station related command has been entered with explicit line specification but line nnn is not allocated to station sid Valid allocations can be determined by means of the operator command X sid L DF3012I nnn sid nnn sid nnn sid As a reply to the command DL the physical line addresses nnn and the present allocation to stations sid are indicated DF3013I f sid NO LINE ACTIVE Response to the commands DS and DV in case of no active line or session has been found STILL DF3014I f sid LINE 111 IS b ACTIVE lnor J This message appears after the entry of activation or stop command for a BSC line or for a station which uses a BSC line for transmission This message is issued for example if the command A Ill has been entered but line Ill is already active or if the command P Ill has been entered but line Ill is not active DF3015I f sid mn text Status report of a
152. des 5 rvs Messages DF8375W DF8376E DF8377P DF8378I DF8379I DF8380P DF8381I DF8382E DF8383W DF8384P OPTION ALL NOT SUPPORTED BY THIS COMMAND This message is issued by the rvs TCP IP task when the option ALL has been used for a command for which this option is not supported INVALID COMMAND PARAMETER This message is issued by the rvs TCP IP task when an invalid parameter is used with an issued command ODETTE TASK HAS BEEN POSTED S SID This message is issued by the rvs TCP IP task when the odette task is posted for termination The socket number and station is shown SPECIFIED STATION 227227222222222222222 This message is issued by the TCP IP task when a command referring to a station is used Either the station could not be found the station was already active for activate command or the station is not active This message is also used to indicate a pending trace for a station which is not active at this time or stopping of a trace COMMAND OK This message is issued by the rvs tcp ip task in response to a command that has been accepted and executed ODETTE TASK HAS BEEN DETACHED S SID This message is issued by the rvs TCP IP task when the ODETTE task has been detached This message is issued by the rvs TCP IP task in response to a display DS command The message displays the used socket number the current tcb state and the station identification rvs s
153. dsname REJECTED DUPLICATE FILE See DF3738E R sid RECEIVING OF dsname REJECTED ODETTE ID MISSING 137 rvsMVS Messages and Codes 5 rvs Messages The sender has not specified the ODETTE ID The transmission is cancelled Make sure that the sender provides for an ODETTE ID that is not blank especially when using a relais station DF88V5P KDUPDAT 88V TYP This message is issued by the FTP task List internal action of FTP task with KD control file For internal use only DF8SWOI JOB jobname jobnumber STARTED TO PROCESS filetyp FILE FOR dsname The data set dsname is processed for filetyp from the job jobname jobnumber FTP job is started for processing of filetyp the data set dsname The filetyp are Header File Trailer file End to End File Delete File DF88W1P KDUPDAT 88W TYP This message is issued by the FTP task List internal action of FTP task with KD control file For internal use only DF88X1E F sid UN ALLOCATION ERROR xxxx yyyy FOR dsn An error occurred during allocation or unallocation of a data set DYNALLOC macro returned with errorcode xxxx and infocode yyyy The codes are described in OS VS2 MVS SPL Job Management DATASET ALLOCATED TO ANOTHER JOB REQUESTED UNIT NOT AVAILABLE VOLUME xxxxxx NOT MOUNTED DF88X2E F sid REQUESTED UNIT yyyyyyyyy UNDEFINED VOLUME xxxxxx NOT AVAILABLE DS ALREADY EXISTING ON VOLUME
154. e File Transfer Protocol task when a dataset has been received One of the following actions and or errors have occurred after receiving DATASET RENAMED dsname With DFSMS the dataset is received under a temporary dataset name with timestamp After complete reception the dataset has been renamed to its final name dsname DATASET NOT CATALOGED xx The dataset could not be catalogued after receiving For the information reason code xx see MVS ESA Authorised Assembler Programming Guide DATASET NOT SCRATCHED RC xxxx xxxxxxxx dsname The temporary dataset could not be catalogued after start of reception For this reason the already allocated dataset is to be scratched which did not end successfully For return and diagnosis codes xxxx xxxxxxxx see DFSMS MVS Diagnosis Reference DATASET NOT RENAMED RC xxxx xxxxxxxx dsname The temporary dataset could not be renamed after reception For return and diagnosis codes XXXX XXXXXXXX See DFSMS MVS Diagnosis Reference DATASET ALREADY CATALOGED dsname The received dataset could not be catalogued after reception because a dataset with identical name dsname already exists The dataset will reside on disk under a temporary name with timestamp DATASET ALREADY CATALOGED AND NOT RE RENAMED RC DATASET NOT CATALOGED AND NOT RE RENAMED RC The received dataset could not be catalogued after reception but has already been renamed to its final name While
155. e assigned to any station This ABEND is coded in the program DFO99Axx The session could not be established no answer to a BIND command This ABEND is coded in the program DF925Axx In case of this error the SYSPRINT DD statement has not been specified This ABEND is coded in the program DF907Axx Any parameter of the parm field is invalid This ABEND is coded in the program DF907Axx The DYNALLOC macro terminated with a non zero return code This ABEND is coded in the program DF907Axx Dynamic allocation error See message DF9071E This ABEND is coded in the program DF907Axx An invalid PARM keyword has been specified This ABEND is coded in the program DF075Cxx Invalid internal PARM length Should not occur error This ABEND is coded in the program DF075Cxx A blank in the PARM string is not allowed This ABEND is coded in the program DF075Cxx An invalid keyword name has been specified in the PARM string 16 rvsMVS Messages and Codes 3 rvs Abend Codes 1013 3F5 This ABEND is coded in the program DF075Cxx An internal text constant in the program output format has been invalid specified Should not occur error 1014 3F6 This ABEND is coded in the program DF075Cxx The PARM characters must be alphabetic 1015 3F7 This ABEND is coded in the program DF075Cxx The PARM characters must be numeric 1016 3F8 This ABEND is coded in the program DF075Cxx If specifying hours the PARM characters must be numeric
156. e code for DTE Octet not aligned Inconsistent Q bit setting NUI Network User Identification problem International Problem general Remote network problem International protocol problem International link out of order International link busy Transit network facility problem Remote network facility problem International routing problem Temporary routing problem Unknown called DNIC Maintenance action 6 2 2 Diagnostic Codes from the DTE 00 Normal initialization or termination 188 rvsMVS Messages and Codes 6 X 25 Cause and Diagnostic Codes Invalid packet type For state DCE timer expired general Incoming call Clear indication Reset indication Restart indication DTE timer expired general Call request Clear request Reset request Restart request QLLC error general Undefined C field Unexpected C field Missing I field Unidentified I field I field too long Frame reject received Invalid QLLC header Data received in non data state Timeout condition XID negotiation error PSH error general Sequence error PS header too short PSH format invalid Command undefined Invalid PSH protocol Data received wrong state Timeout condition Packet not allowed Invalid M bit packet
157. e created a second time UNCATLGD xx S sid mn dsname NOT b DELETED yy zz J The data set dsname has been completely sent to station sid After this the data set disposition is performed In this case execution of the data set disposition failed The data set could not be uncataloged or could not be deleted 68 rvsMVS Messages and Codes 5 rvs Messages DF3614I DF3615E DF3616E DF3616E DF36251I DF3626E DF3634E DF3635P DF3701P xx denotes the returncode register 15 in decimal of the CATALOG macro yy denotes the returncode register 15 in decimal of the SCRATCH macro zz denotes in decimal the scratch status code of the SCRATCH macro for a description of these return codes see for example the IBM manual OS VS2 SPL Data Management KEPT S sid mn dsname TRANSMISSION COMPLETE DELETED luncaTLG The transmission of the data set is complete The rvs response record of the remote station has been received The rvs stream ended without any failure and the disposition of the data set has been executed S sid mn WRONG R RECORD RECEIVED A rvs response record has been received but the contents of the record is not compatible with the contents of the actual record of the rvs control data set S sid mn NO RACF AUTHORIZATION FOR dsnl S sid mn OLDDSN dsn2 The data set dsn1 shall be transmitted to station sid During this time an open error occurs System Comple
158. e displays the error and info code of the unallocation R sid mn RECEIVED RECORD LENGTH nn LARGER THAN BLOCKSIZE mm The length of the received record nn is inconsistent with the blocksize mm and the record format not spanned specified by the transmitting station at beginning of the transmission R sid mn DATA SET COULD NOT BE OPENED The OPEN macro executed for the data set to be received failed R sid mn dsname INVALID FIELD field value IN HEADER The received rvs header record contains a field field with an invalid value value R sid mn EFFECTIVE SPEED IS nnn BPS This message appears during rvs trailer record processing at the end of a receiving sending process nnn indicates the average speed value during the whole duration of transmitting the data set R sid mn REMOTE STATION NOT AUTHORIZED TO SPECIFY PROCESSING OPTIONS A data set has to be received from station sid The transmitter of the data set has specified some remote options i e specification of the receive volume The station sid is not authorized for specifications like this The data set will be received normally The parameters specified by the transmitting station are ignored For a definition of station dependent authorization see Installations Manual description of the rvs Stations Table parameter OPTIONS R sid mn REMOTE STATION NOT AUTHORIZED TO REPLACE DATA SETS A data set has to be received from station sid The tra
159. e of real dataset to be send CD Creation date of send request CT Creation time of send request SD Last start date of transfer of real dataset ST Last start time of transfer of real dataset f sid INVALID SUBPARAMETER The command F sid was wrong specified f sid VTAM SUBTASK NOT ACTIVE Modification of the incore session s table is possible only if the VTAM control task is active f sid mn INVALID MODE NUMBER An undefined session mn has been specified f sid LINE IS STILL ACTIVE The command F sid pp is only valid when line control is terminated f sid VALID PP S ARE ppp ppp In case of a wrong program profile specification in the command F sid PP ppp this message appears and indicates a list of valid program profiles f sid SIZE PARAMETER MUST BE 250 2000 The specified SIZE subparameter of the command F sid was not within the range 250 2000 f sid TOO MANY SUBPARAMETER For a subparameter of the command F sid to many values have been specified f sid SUBPARAMETER TOO LONG A value for a subparameter of the command F sid has been specified and the value consists of to many characters F sid INVALID VALUE For a parameter of the command F sid a wrong value has been specified F sid NO ENTRY PROCESSED 78 rvsMVS Messages and Codes 5 rvs Messages DF4411E DF4413E DF4414E DF4415E DF4416E DF4417E DF4800I DF4801I DF48020 DF4803I DF
160. e previous trace entry in units of 1 100 seconds ofst denotes the offset within the module line control program where the trace entry is written trace point sid denotes the ID of the remote station if available to which the line Ill was connected event denotes the type of event which was recorded The following types may occur UNSPECIFIED no special event significant trace data are only time and offset within the program BTAM IO IO operation of the line the assigned BTAM macro is also displayed STOP REQ a stop request has been detected operator has entered a stop command CANCEL REQ a cancel request has been detected operator has entered a cancel command LCP2 STARTED line control program 2 DF057B00 has started LCP2 ENDED line control program 2 DF057B00 has ended BTAM RECOVERY the BTAM error recovery routine within rvs was entered This routine is entered in some cases independent whether an error has occurred or not EXT TRACE an external trace entry was written IOSUBTASK ATT the subtask for data set IO was attached created 57 rvsMVS Messages and Codes 5 rvs Messages DF3047I DF3047I DF3047I DF3047I DF3047I DF3047I DF3047I DF3047I DF3047I DF3047I DF3047I DF3048W DF3049I DF3050I DF3051E DF3052E IOSUBTASK DET the subtask for data set IO was detached deleted For some of these events additional information may be displayed REQ ISSUED or REQ COMPLETE indicates
161. e received bytes or records does not match the byte or record count in the rvs protocol trailer or response record During receiving of an rvs protocol data record D record the length field contains a data length which exceeds the line buffer size or a data record has been received and a length field contains an invalid or inconsistent value see the error message of the monitor which describes the error in detail During expanding data a record length was found which exceeds the blocksize of the received data set A field in rvs protocol header record H record has an invalid format Error during data compression Only in case of PDS transfer a PDS is to be sent but the remote station does not support PDS transfer or a PDS is to be received and loading of the PDS failed A file is to be received and cataloged after transmission but a file with the same name is already existing cataloged Receiving of this file will be rejected The transmission of a file is rejected by exit DFUX001 This mostly means that the user is not allowed to send or receive the data set access denied by security system The REPLACE option has been specified but the necessary space could not be obtained in the receiving station rvsMVS Messages and Codes 2 rvs User Codes 116 120 124 128 132 136 140 144 148 152 160 164 168 172 176 180 074 078 07C 080 084 088 08C 090
162. e size of the file to be sent is not available whithin the send request should not occur or a restart is to be done receive The size of the file must be determined by reading the file TIMEOUT problems may be caused by very big files S ORT ACCM SESSID SEND OF EERP FAILED DSN dsname This message is issued if an EERP could not be sent the remote station did not respond with an RTR OFTP protocol unit to the sent EERP The EERP is set into HOLD status a next attempt for sending is not be made before the holdreset time interval has expired S ORT ACCM SESSID REMOTE STATION DOES NOT SUPPORT function This message is issued if a file is to be sent to the remote station but the remote station does not support the required function function may be PDS TRANSFER the file to be sent is a PDS or RECEIVING OF FILES the remote station can only send files This message is followed by DF9446E The send request is cancelled no further restart will be made after this situation S ORT ACCM SESSID TRANSMISSION OF dsname CANCELLED This message is issued in conjunction with message DF9445E The transmission of the PDS can not be executed so the transmission is cancelled and the send request is deleted S ORT ACCM SESSID SYSTEM ABEND sss DETECTED RECOVERY IN PROGRESS This message is issued when an abend sss has occured whithin the OFTP task A special recovery is done for system abends B37 D37 and 837 Other abends
163. ecause of no resources available to handle the call request nn RECEIVED ON SESSION CAUSE DIAG This message is issued by the rvs X 25 CTCP task when an X 25 Clear or Reset packet is received on an active session The message shows the Logical Unit name and the station id of the virtual circuit on which the Clear or Reset was received and the clearing cause and diagnostic code as found in the packet If the clearing cause and diagnostic code are FF an Invitation to Clear PAD message has been received and the CTCP will send a Clear request for the session For cause code and diagnosis code see chapter 6 of this manual nn INTERRUPT RECEIVED ON SESSION DATA This message is issued by the rvs X 25 CTCP task when an X 25 Interrupt packet is received on an active session The message shows the Logical Unit name and the station id of the virtual circuit on which the Interrupt was received and the data in the interrupt packet No action is taken when an interrupt packet is received nn DIAGNOSTIC RECEIVED CODE REASON This message is issued by the rvs X 25 CTCP task when a diagnostic packet is received from the IBM NPSI product The message shows the code and reason as received in the packet No further action is taken for this type of packet nn CLEAR CONFIRM RECEIVED This message is issued by the rvs X 25 CTCP task when an X 25 Clear confirmation is received The Clear confirmation is received in resp
164. econd CANCEL command reached NOTE All activ sessions will be enforced terminated independent of the state of remote station 22222222 This message is issued by the rvs APPC driver task trace routine Shown is the name of driver task subroutine which gets control For internal use only 133 rvsMVS Messages and Codes 5 rvs Messages Messages of the FTP Driver Task STARTED DF8800I D sid sesid FTP DRIVER TASK b VERSION STOPPED yvv dd mm yy tt mm aa bb cc Start or stop of FTP Client Task message vvv specify version of FTP Client Task dd mm yy tt mm time of assembly aa bb cc time of last changes in the FTP Client Task DF8803E D sid sesid FTP DRIVER ABEND CODE EP PSW The FTP Client Task issues this message when an abend occurs The message shows the system abend code the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done after all subtasks have been terminated DF8804I D sid sesid REGS 0 7 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXK XXXXXXXX The FTP Client Task issues this message when an abend occurs The message shows the content of the registers 0 to 7 at the time of the abend DF8805I D sid sesid REGS 8 15 xxxxxxxx XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXK XXXXXXXX The FTP Client Task issues this message when an abend occurs The message shows the content of the regis
165. ection with station sid will be broken f sid 111 INVALID PASSWORD RECEIVED Additional to the identification a password exchange after identification is defined for station sid see rvs stations table But the received password did not match the values specified for station sid within the rvs stations table parameter RECVPW After this the line connection with station sid will be broken f sid 111 NO VALID STATIONS ENTRY FOUND FOR sid A request for autodial to station sid has been passed to the line control program But the stations entry for sid could not be found This error should not occur rvs program error f sid 111 NO DIALNUMBER SPECIFIED FOR sid A request for autodial to station sid has been passed to the line control program But the stations entry for sid does not contain the number to be dialed see rvs stations table The dial request cannot be processed f sid 111 CONNECTION FAILED The line connection failed is broken There are many reasons which may leed to this result line errors timeouts incorrect definition of the transmission protocol to be used and others To determine the reason for this a trace rvs or GTF should be started f sid 111 RESETPL MACRO FAILED RC X xx 102 rvsMVS Messages and Codes 5 rvs Messages DF5516E DF5517W DF5556E Execution of a RESETPL macro failed this error should not occur After this message the line connection will be b
166. er data set transmission the number of received bytes is not equal to the number of bytes specified by the transmitter This ABEND is coded in the program DF035Mxx rvs protocol record mismatching A data record has been received without a preceding header record This ABEND is coded in the program DF035Mxx In the rvs protocol header record an invalid record or block length has been specified by the transmitting station This ABEND may occur after reception of a data set the received data set could not be closed As a result of this error no response record will be sent back to the sending station The transmission must be repeated a restart is not possible in this case The transmission will be marked as abended with a record count of zero This ABEND is coded in the program DFO35xxx During the initialization phase of a transmission the receiving station creates an active receive record An error occurs during the try to insert the record in the rvs control data set See Operations Manual Chapter 5 5 Eliminating Physical Errors of the Control Data Set This ABEND is coded in the program DF036Bxx Should not occur error This ABEND is coded in the program DF037Bxx Should not occur error This ABEND is coded in the program DF037Bxx Occurs in relation with Dynalloc error 420 see OS VS2 MVS Job Management Should not occur error This ABEND is coded in the program DF047Axx Should not occur error This ABEND
167. er processing the output data set dsname by job jobid see message DF90811 the data set has been deleted M sid mn text The message text has been received from the remote station This may be a reply to the command Q sid or the operator of the remote station has sent this message f sid mn sid2 dsname time HL RESPONSE IGNORED RECORD NOT FOUND The receipt of a high level response record from the final station sid2 after reception of the data set dsname could not be written to the control data set because there was no related AS type control record which could have been updated The high level response record is a end to end response message using the function transmission of data sets via relais station s f sid mn SEND r RECORD FAILED SENSE ssss uuuu 147 rvsMVS Messages and Codes 5 rvs Messages DF9106E DF9107I DF9108P DF9135P DF9136P DF91409 DF9203P DF9204E DF9205E DF9206E The transmission of a rvs record type r terminates with a failure ssss VTAM system sense code UUUU user sense code see chapter 4 within this manual for an explanation of the different user sense codes f sid mn text Extention to message DF9105E If a user sense code is specified a short text is given as explanation text is a short description of the user sense code which has been detected See chapter 4 within this manual for a list of possible user sense codes f sid mn te
168. essage is the headline of the messages DF43021 DF43041 DF4305 DF43061 and DF4308I It is a response of a DQ B DQ V DQ L DQ X DQ T or a DQ sid command In this message the string message string could be KD STATIONS ONLY or cccccc STATIONS with cccccc description BTAM BTAM VTAM lvram LU6 2 active send request for LU6 2 station s X 25 Ix 25 SID J lsia J changes of active send requests COMPONENT NOT ACTIVE This message is displayed after one of the commands described in DF49031 and the component isn t started x x k SID NOT FOUND IN STATION TABLE EXIST KD RECORD This message is displayed after a DQ sid command if the station table of the running rvsMVS does not contain the station sid But active send requests are queued in the control dataset of the running rvsMVS 80 rvsMVS Messages and Codes DF4905I ERREAK NO CHANGES KKKKKK This message is displayed after a DQ Q command if there were no changes of queued send requests are made since last DQ Q command Changes would be that the sending of a datasets is completed or that a new dataset is queued for sending DF49061I sidl nn vmm sid2 nn vmm sid3 nn vmm sid4 nn vmm sid5 nn vmm This message is displayed after one of the commands described in DF4903I The message shows the number of active send requests nn for the station sid and the changes since last DQ Q co
169. essages DF8355I DF8357E DF8358P DF8359W DF8360I DF8361P DF8362P DF8363E DF8364P DF8365I 727277777777777777777777777777777797777777777777 This message is issued by the rvs TCP IP task in order to display a longer message text describing an error code API MODULE COULD NOT BE LOADED This message is issued by the rvs TCP IP task when the TCP IP interface is not available The TCP IP task will be terminated after this event This message is issued by the rvs TCP IP task when an IP connection has been established either after connect or accept The message shows the socketnumber remote portnumber and remote IP address An OFTP task will be started after this event SESSION START REJECT NO RESOURCE TCB AVAILABLE This message is issued by the rvs TCP IP task in response to an operator activate station command if no resources tcb are available to handle a call request A REMOTE STATION NOT READY This message is issued by the rvs TCP IP task when a connect request has not completed successfully The remote partner addressed by IP address and TCP port did not respond A TCP IP SESSION LOST S This message is issued by the rvs TCP IP task when loss of a session has been detected All activities for this connection are terminated A READ COMPLETE S L DATA This message is issued by the rvs TCP IP task when a read macro has completed successfully The me
170. et ISO 646 In the message is shown virtuell filename of the dataset SFIDDSN Z ORT ACCM SESSONID RELATED SFIDDSN dsn QD qdate QT qtime This message is issued in addition to Start File Negative Answer SFNA messages stating the name of the datset that has been denied Queuing date and time ist also stated Z ORT ACCM SESSONID NO INVALID CODE TRANSLATION TABLE USED This message is displayed when code translation is requested but no or an invalid code translation table is used The name of the code translation table is shown S ORT ACCM SESSID WAITING FOR SYSTEM READY MESSAGE SSRM FROM STATION This message is displayed after connection request when the partner sends no answer S ORT ACCM SESSID UPDATE OF SEND REQUEST FAILED RC 77 This message is displayed when file is to be transmitted and the update STARTDADE TIME of the send request failed should not occure This message may inicate a damaged rvs control dataset In this case it is recommended to check the control dataset IDCAMS VERIFY INDEXTEST DATATEST and to start a recovery if necessary This message is followed by DF9446 TRANSMISSION CANCELLED S ORT ACCM SESSID RESOURCE NOT AVAILABLE TARGET This message is issued when the targed dataset name is in use by an other receiving task or decription decompression task receiving of the file will be rejected Z ORT ACCM SESSONID DATASET WITH SAME QUEUING DATE TIME ALREADY RECEIVED Z ORT ACCM SESSON
171. fer to message DF52011 Messages DF5V61P until DF5V80P are for possible error detection only They are not in effect for users purpose DF5V61P D IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IK The following text may be ATTACH DF310A RC NOT ZERO Operator request gt CANCEL OPERATOR REQUEST gt 2ND STOP gt EXIT Operator request gt STOP DF310A attach error Status messages of the Service Provider Task Receive Dispatcher DF5V65P D 2272727272222222 cccccccc Return code message for access to the Security Key data Set with 2222222222222 RETURN CODE PUB KEY or RETURN CODE PRV KEY ccccccce VSAM return code and program return code DF5V66P D 22 HHH 3229999999977 727979999999 77 7799799999999 Internal file names used by the Service Provider Task Protocol message only DF5V67P D 72727277777777777777777777777777777779797777 First 54 characters of the KD record Protocol message only DF5V68P D 22222222 USED TRANSLATION TABLE ADR aaaaaaaa The message indicates a translation table is used for receive request Comp Secr DF5V72P D message Status Message from the Service Provider Task receive request DF5N80P D message DF5V99P D HHE 7727272777 77777772 777777797 7777777 This message is issued if an internal modul trace will be processed Protocol message only DF5X01I RECEIV_DISP SUBTASK STARTED VE
172. fied in a command cannot be found This message is issued by the rvs X 25 CTCP task when a command refering to a station is used Either the station could not be found the station was already active for Activate command or the station was not active nn OK This message is issued by the rvs X 25 CTCP task in response to a command that has been accepted and executed This message is issued by the rvs X 25 CTCP task in response to a Display DS command The message shows the ACB name used by the CTCP task and the name of the Logical Unit used for X 25 link communication LV states the last modification date of program DFO95A nn VCB 227272222 LU SID This message is issued by the rvs X 25 CTCP task in response to a Display DS command The message displays information for a Virtual Circuit Block VCB and shows the VCB number the current VCB state the virtual circuit Logical Unit associated with the VCB if an X 25 connection exits and the station identification rvs station code and Odette station code if a station is connected nn BUFSIZE CREDIT COMPRESS RESTART SPECIAL LOGIC This message is issued by the rvs X 25 CTCP task in response to a Display DS command The message shows the exchange buffer size used for the connection the established credit value and whether the compress restart and special logic options are used or not This message is issued by the rvs X 25 CTCP task in response to a Display DS command
173. fied in the A record is using some features At least one of these features is not supported by the local station If possible the transmission will be done by using a lower level of features S sid mn EFFECTIVE SPEED nnnnn BPS After transmission of a trailer record the transmission speed is determinated for the current data set The greater the data set the more precise is the statement concerning speed With very small data set or in the event of a restart the speed determined is severely reduced by intensive computer activities ALLOCATION OPEN CONTROL CLOSE S sid mn r RECORD RECEIVED DSN dsname Reciving of a rvs protocol record type r is displayed on printout 149 rvsMVS Messages and Codes 5 rvs Messages DF9236P DF9237W DF9238I DF9301I DF9303P DF9305E DF9306E DF9307I DF9308E DF9309E S sid mn r RECORD HAS BEEN SENT The transmission of a rvs protocol record type r is displayed on printout f sid mn INVALID NUMERIC VALUE IN r RECORD 0 ASSUMED A rvs protocol record type r has been received from station sid which has an invalid structure This message indicates a program error in the program of the remote station sid F ORT MO MAXIMUM ERROR RETRIES REACHED FOR DSN name The maximum error retries reached for dataset The transmission will be cancelled SCRATCHED JCL DATA SET NOT UNCATALOGED RC xx f dsname NOT SCRATCHED RC yy zz J A data set has bee
174. fied partner number index mm is not defined in station table entry nn SPECIFIED PARTNER NUMBER INDEX mm NOT DEFINED FOR SELECTED CTCP This message is issued by the rvs XOT CTCP task if the operator command A SID Cnn Nmm was entered In this case the specified partner number index is defined for the station but not for the specified CTCP This message is issued when the rvs XOT CTCP task sends an outgoing call packet to a partner station with the specified X 25 number This message is issued by the rvs XOT CTCP task when an virtual control block VCB has been found and no appropriate session control table SCT entry exists rvs will handle this problem and release the VCB entry nn ACTIVE ODETTE TASK HAS BEEN DETACHED SESSION This message is issued by the rvs KOT CTCP task when an active ODETTE task has been detached This happens only in that case that the subtask dies not respond any more nn ODETTE TASK NOT RESPONDING WILL BE CANCELLED SESSION This message is issued by the rvs XOT CTCP task when an ODETTE task is no longer responding In this case it will be detached nn INVALID BUFFER BUFFERADDRESS DETECTED BUFFER NOT RELEASED This message is issued by the rvs KOT CTCP task when a buffers is to be released In this case an invalid buffer address has been detected and the buffer will not be released nn JES ALLOCATION PROBLEM This message is issued by the rvs XOT CTCP task if the JES3 alloc prob
175. for a session but the session has already terminated The send request will be released in each case If a send request should be assigned to a session selection of a send request the transmission will be restarted automatically when a new session to the remote station sid has been established S sid acme nm SCT STATION ENTRY POINTER NOT AVAILABLE Similar situation as described for message DF5237P the session is not ready for transmission e g session termination because of line problems S sid acme nm STATION POINTER OF SCT ENTRY HAS CHANGED Similar situation as described for message DF5235P S sid acme nm SEND REQUEST AVAILABLE This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates that selection of a send request for send session nm to station sid and access method acme has been successfully ended send request is found S sid acme nm NOTHING TO SEND This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates that selection of a send request for send session nm to station sid and access method acme has ended but in KD dataset is no send request for sid found S sid acme nm DISPATCH SESSION This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates that selection of a send request for send
176. ge record format not supported or PDS transfer not supported 05 maximum record length not supported 06 file size too big 10 invalid record count 11 invalid byte count 12 access method failure 13 duplicate file 99 unspecified reason Z sid accm sessonid INVALID RESTART RECEIVED FOR DSN dsn This message is issued by the Odette File Transfer Protocol task when a Start File Positive Response SFPA protocol unit is received in response to a start file transfer request The SFPA protocol unit received indicates a restart point beyond the restart point requested by the task In the message is shown the file name associated with the restart request 155 rvsMVS Messages and Codes 5 rvs Messages TERMINATION STARTED This message is issued by the Odette File Transfer Protocol task during file transfer An unrecoverable i o error occurred during disk read or write DF9421I A sid accm sessonid CONNECTION ESTABLISHED This message is issued by the Odette File Transfer Protocol task when a connection has been established to the partner station DF9422P A sid accm sessonid BUFSIZE nnnnn CREDIT nnn COMPRESS RESTART SPECIAL LOGIC DIRECTION This message is issued by the Odette File Transfer Protocol task when a connection has been established to the partner station The message shows the exchange buffer size used for the connection the established credit value and whether the COMPRESS RESTART and SPECIAL LOGIC option
177. ges and Codes 5 rvs Messages DF5260P DF5261P DF5262I DF5270P DF5271P DF5272P DF5280P DF5299P S sid acme nm POSTCODE 4 BUT SESSION IS ALREADY DISPATCHED This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates internal problems within the rvs monitor for send session nm to station sid and access method acme Report this message to the system programmer S sid acme nm POSTCODE 4 BUT SESSION IS NOT JUST DISPATCHABLE This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates internal problems within the rvs monitor for send session nm to station sid and access method acme Report this message to the system programmer SEND TIME LIMIT EXCEEDED FOR DATASET name S sid acme nm ULS CHECK STARTED SID sid FOR DATASET dsn This message indicates that a ULS check for send request is started for station sid and for data set dsn S sid acme nm CHECK USER TABLE FAILED FOR RACF racfid This message indicates that a ULS user check failed for racfid S sid acme nm CHECK PERMISSION TABLE FAILED This message indicates that a ULS permission check for send request failed X ORT ACME 12345678 USER SEPARATION LOG RECORD NOT FOUND This message indicates that a User separation log record is not found X sid
178. ges and Codes 5 rvs Messages The activation respectively deactivation of all accordingly signed lines respectively sessions has been performed without error The values of x y may be x A activate P stop y BTAM VTAM or DF3038I x ALL y ERROR DETECTED It was not possible to activate all signed lines without failure Reason An error occurred during line allocation or after message DF3036A the command P sid nnn has been entered to stop activation DF3039I COMMAND FROM START MEMBER command Display of commands which are executed automatically after start of the rvs monitor These commands may be specified within member START of the rvs tables data set which is allocated with DD name START to the rvs monitor DF3040I parameter value Message to display a parameter value if one of the following commands has been entered DSPTI DUMP HOLD PMSG ROUT SDELAY STORAC TIME and VOLUME For a description of these commands see Operations Manual DF3040I x25group CTCP list Message to display all defined X25 groups if the command X25GROUP has been entered For description of these command see Operations Manual DF3040I NO X25GROUP DEFINED This message occurs if the command X25GROUP has been entered but no X25GROUP has been defined DF3040I MSG function name PROCESSED RC rc This message occurs if the command MSG function name has been entered function denotes one of the
179. he conversation typ the synclevel and the the name of the file server program Also shown is whether trace is active A or not I INVALID COMMAND PARAMETER This message is issued by the rvs APPC task when an invalid parameter to a used command is detected This message is issued by the rvs APPC task manager routine when a session start request has been received The request to start a session is accepted The message also shows the qualified network name of the partner sid and the mode name to use This message is issued by the rvs APPC task in response to an Activate station command The command cannot be honored as session negotiation is being done for the station DEFINED RESET TO LOW 180 rvsMVS Messages and Codes 5 rvs Messages This message is issued by the rvs APPC task in response to a command A sid PRIO xxxxxx but this prio isn t defined in the logmode table Prio will be reduced to PRIO LOW DF9780P F LU 2 22 2 ANTEFLAG 77 PRG name DF9790P F L N M G 47744474 P C Q DF9791P F L M L77777 Messages DF9780P until DF9791P are for error detection only They are not in effect for users purpose DF9799P This message is issued by the rvs APPC control task trace routine Shown is the name of control task subroutine which gets control For internal use only 181 rvsMVS Messages and Codes 5 rvs
180. he displacement in bytes to the beginning of the receive module see Advanced Communication Function for VTAM Programming DF9904I R sid mn SESSION TERMINATED FOR LU 1lu The session mn to the logical unit lu terminated DF9905P R sid mn TRACE STOPPED ALLOCATION ERROR The trace for session mn to station sid has been stopped by the rvs monitor because the output data set for this trace could not be allocated DF9906P R sid mn BINDAREA bindarea 182 rvsMVS Messages and Codes 5 rvs Messages DF9909P DF9910E DF9911E DF9915P DF9916E DF9917E DF9918E The BIND parameter used by establishing session mn to station sid are listed R sid mn SESSION NOT YET ESTABLISHED TRY LATER One of the commands M sid Q sid or R sid has been entered The execution of these commands requires an active operator session to station sid The activation of the operator session has been already initialized i e by using the command A sid O but the session could not be established The entered command will be ignored and can be entered again after activation of the operator session R sid mn SESSION COULD NOT BE ESTABLISHED The requested session could not be established no response to a BIND request NOT FOUND R sid mn LU luname NoT ACTIVE xx yy Ssss REJECTED J The connection to the logical unit luname could not be established For a description of return code xx feedb
181. he file type In the message is also shown the volume and dataset name of the file to be transferred Z sid accm sessonid DSN dsn VOL volume STARTING This message is issued by the Odette File Transfer Protocol task when a file transfer is to begin In the message is shown the volume and dataset name of the file to be transferred R sid accm sessonid UNKNOWN EERP RECEIVED DSN dsn This message is issued by the Odette File Transfer Protocol task when an End to End Response EERP protocol unit is received but the EERP can not be associated with a previous file transfer In the message is shown the file name indicated in the EERP protocol unit ORIG origin DEST destination DATE yyddd TIME hhmmss This message is issued by the Odette File Transfer Protocol task when an End to End Response EERP protocol unit is sent or received Additional data are displayed here origin and destination of the EERP and the queuing date and time of the corresponding dataset S sid accm sessonid EFNA direction rc reason This message is issued by the Odette File Transfer Protocol task when an End File Negative Response EFNA protocol unit has been sent or received after a complete file transfer In the message is shown the code used in the EFNA protocol unit Refer to the document Odette specifications for file transfer for a further explanation of the code code reason 01 invalid filename 02 invalid destination 03 invalid origin 04 stora
182. he reference dataset ST ddd hh mm or ET ddd hh mm Start End date and time for the transmission nnnnnn RE or BL Number of datarecords RE or datablocks BL which have been already transmitted received bbbb bbb MB Number of bytes of the dataset P nnn Displays the priority of the transmission value is between 0 and 255 ser This parameter is displayed only when the dataset has been queued with option SERIAL YES END means that the transmission is complete ABE means that the transmission has been terminated with an error REJ means that either the installation exit DFUX001 terminated with a return code not equal 0 see also message DF9201E or DF5624E or in case of PDS transfer the remote station does not support PDS transfer ET ddd hh mm ss 82 rvsMVS Messages and Codes 5 rvs Messages End date and time for the transmission DS dsn Displays the dsname of the dataset It is possible that the dsname used in the rvs messages is different from the physical dsname of the data set in case of using the rvs rename function dsn is the physical dsname In case of PDS transfer dsn is the physical name of a sequential work dataset unloaded PDS which is will be transmitted by rvs ESTRT ddd hh mm ss Earliest date and time for the transmission This parameter is only displayed for AS CS records RECL nnnnn Record length of the dataset only for fixed record lenth RU uuuuuuuu TU uuuuuuuu RACF and
183. he registers 8 to 15 at the time of abend DF9706E ACB OPEN FAILED ACB RSN This message is issued by the rvs APPC task when open of the ACB to use for VTAM communication fails The message shows the ACB name the reason code for open failure and an explanatory text The APPC task will terminate when the ACB cannot be opened DF9707E UNSOPPORTED VTAM VERSION ACB This message is issued by the rvs APPC task when open of the ACB has completed and the ACB is checked for supported VTAM options The ACB check routine found that the VTAM Function Vector List support was not present indicating a VTAM release earlier than ACF VTAM version 2 The rvs APPC support requires ACF VTAM version 3 2 or later DF9708E NO VTAM APPC LU 6 2 SUPPORT ACB This message is issued by the rvs APPC task when open of the ACB has completed and the ACB is checked for supported VTAM options The ACB check routine found that the VTAM version used does not support APPC LU 6 2 The rvs APPC support requires ACF VTAM version 3 2 or later DF9709E ACB CLOSE FAILED ACB RSN 175 rvsMVS Messages and Codes 5 rvs Messages This message is issued by the rvs APPC task when close of the ACB used for VTAM communication fails The message shows the ACB name and the reason code for close failure The rvs APPC task will continue termination DF9710E SETLOGON FAILED REASON This message is issued by the rvs APPC task when a VTAM SETLOGON request fails The
184. he used rvs load library contains an expiration date Such a date may be included in load libraries for test installations If this date has expired the rvs Monitor does not perform any 56 rvsMVS Messages and Codes 5 rvs Messages DF3045E DF30461I DF3047I DF3047I action The monitor will stop just after it has been started To solve this situation a new load library is required COMMAND REJECTED USE OF cmp COMPONENT NOT INDICATED A command related to the component cmp has been entered but either the component is not included in the software or the use of this component is not specified as an rvs startparameter for example X25USE YES NO or the use of the component is not allowed because of licence key restrictions The specified command is rejected shipped ACTIV COMPONENTS list of b components lactive J Included active components of rvsMVS may be SNA BSC X25 LU62 TCP IP or combinations This message will be issued at monitor start time before and after check of licence and parameters U 111 LAST EVENTS OF THIS BSC LINE SUBTASK U 111 T time O ofst SID sid EV event Display of internal trace data for BSC line Ill These messages are displayed if the command U IIl is entered Internal tracing is automatically done for switched BSC lines after activation of the line time denotes the time when the trace entry was written absolute value with format HHMMSSTH or time difference to th
185. ication 37 rvsMVS Messages and Codes 5 rvs Messages DF1906E DF1908W DF1909I DF1910E DF2000P DF2001P DF2002P DF2002P DF2002P PARAMETER DOPERM YES IGNORED BECAUSE OF MVS RELEASE rel The rvs start parameter DQPERM YES has been specified But this parameter will be ignored because the MVS release rel is not at least MVS SP 2 2 0 or a following release MVS release 2 2 0 is required for this function because IBM made some downward incompatible software changes within MVS release SP 2 20 INCONSISTENT PARMVALUES TEXTLREC TEXTBLSZ SET TO DEFAULTS 2048 6000 One or both of parameters TEXTBLSZ TEXTLREC have been specified but the specified values are invalid or inconsistent either TEXTLREC is less than 5 or TEXTBLSZ is greater than 32760 or TEXTBLSZ is not greater than or equal to TEXTLREC 4 As a result of this error the default values 2048 6000 will be used SECURITY FEATURE ONLY FOR RECEIVING PART OWN ENCRYPTION KEY MISSING The parameter SECURITY EXT have been specified but without any security key identification This feature can t be used INCOMPLETE PARAMETER SPECIFICATION FOR SECURITY FEATURE SECURITY EXT MISSING The parameter KEYID have been specified but no SECURITY EXT parameter This feature can t be used space SP nnl mmIK SP nn2 mm2K TOTAL kkkk K Display of the used virtual storage Subpool nn has a size of mm Kbytes the used space of the address space
186. ime of queuing dataset 123 data set name DF5X22P 123456789012345678901234567890123456789012345678901234567890 The following text may be First 54 characters of KD record x k MAX NUMBER OF RDS TASK EXCEDED x kk k ATTACH FAILED DFO52V ATTACHED kk RDS STOP k kk RDS CANCEL WAITING RDS TASK ACTIVE x k TASK ACTIVE xk NO ACTIVE RDS TASKS kk k RECORD DONE IGNORED k k RECORD IN HOLD STATE IGNORED TASK WITH KD RECORD ACTIVE kkkk RDS BUILD ax QUEUE ELEMENT FOUND kk k NO RECV REQESTS FOUND 98 rvsMVS Messages and Codes 5 rvs Messages DF5X25P DF5X271 DF5X99P DF5401P DF5402W DF54031 DF5404I DF5405E DF54061I DF5407I All message are protocol messages only NO STATION TABLE FOR SID The Receive Dispatcher detects an error The record can not processed RDS TASK COULD NOT BE STARTED NOT ENOUGH MEMORY This message is issued by Receive Dispatcher task when activation of further subtask is rejected because of storage shortage X ORT ACME 12345678 Internal trace message of Send Dispatcher ID nn RC 00 REC key ORT sid dsn RD readydate RT readytime SD startdate ST starttime This message is generated if the access to the control data set ended with certain return codes The message may appear if errors occur during access the control data set ONL
187. ine nnn An error xxxx with info code yyyy occurred SVC99 Error Codes see OS VS2 SPL Job Management DF6903E A sid CANNOT ALLOCATE LINE nnn UCBNAME NOT DEFINED This message occurs when an invalid value for parameter UCBNAME was specified In this case the dynamic allocation of the line is not possible 116 rvsMVS Messages and Codes 5 rvs Messages Messages of the TCP IP line driver of rvsMVS for the TCP IP stack of IBM DF8301I TCP IP INITIALIZATION COMPLETE LV This message is issued by the rvs TCP IP task when task initialization is complete The level of the program is shown DF8302P rvs TCP IP TERMINATION This message is issued by the rvs TCP IP control task when task termination has started or is complete DF8303I TCP IP SUBTASK ACTIVE LV 72 This message is issued by the rvs TCP IP task in response to a display DS command The message shows the level of the program DF8304I 22272222227 FAILED S ERRNO This message is issued by the rvs TCP IP task when a TCP IP request fails The message shows the failing request the socket number for which the request was issued and the error number For error number ERRNO see IP Programmer s Reference SC31 8787 in Appendix B Return Codes Remark For request GETHOSTID the error number is not available set to zero Use the TSO command HOMETEST to get more information about the kind of the
188. ion which is not active at this time or stopping of a trace COMMAND OK This message is issued by the rvs tcp ip task in response to a command that has been accepted and executed ODETTE TASK HAS BEEN DETACHED S SID This message is issued by the rvs TCP IP task when the ODETTE task has been detached This message is issued by the rvs TCP IP task in response to a display DS command The message displays the used socket number the current tcb state and the station identification rvs station code and odette station code if a station is connected A IP ADDRESS MISSING GETHOSTBYNAME ACTIVATION REJECTED This message is issued by the rvs TCP IP task when an activation command is to be executed The IP address of the remote station is not available not defined within stations table or not available by a name server The activation is rejected ACTIVATE REJECTED FOR STATION ISTATUS INACTIVE This message is issued by the rvs TCP IP task when an activation command is rejected due to the initial status INACTIVE of the stations entry Set the status to ACTIVE COMMAND REJECTED TERMINATION OF rvs TCP IP IN PROGRESS This message is issued by the rvs TCP IP task when an activate command has been entered but termination of the rvs TCP IP task has already started UNSOLICITED EVENT OCCURRED RC TCP IP ADDRESS SPACE HAS TERMINATED This message is issued by the rvs TCP IP task when the unsolicited event exit i
189. ion of the transmission is invalid The origin of the transmission is invalid The record format of the file isn t supported The maximal record length of the file isn t supported The size of the file is too big The sent record count is invalid The sent byte count is invalid Access method error Duplicate file name Restriction error ULS Permission error ULS Unspecified reason 10 rvsMVS Messages and Codes 3 rvs Abend Codes 3 rvs Abend Codes In the event of serious errors subtasks of the rvsMVS Monitor or rvsMVS Utility Programs terminate abnormally The following codes may appear Code Code decimal hexadecimal Meaning 280 118 This ABEND is coded in the program DF028C00 The allocation of a work data set for automatic job start was not possible 282 11A This ABEND is coded in the program DF028C The code may occur a during accessing OPEN READ the member RVS TABLES STAPEJC RVS TABLES RTAPEJC b during writing received data to the sysout queue c during starting a reader in order to initiate jobs to copy data from tape to disk transmitting a tape or to copy received data from a workfile to a tape see rvsMVS Installation Manual 310 136 This ABEND is coded in the program DF031C The abend may occur during processing of command MSGOUT If DD statements SYSWTO and or RVSDUMP are assigned to sysout classes these files are closed and unallocated The following al
190. ithin the rvs internal bufferpool aa denotes the amount of storage occupied by all unused buffers of the pool bb denotes the storage which is still available for the bufferpool and cc denotes the count for execution of the bufferpool service routine NUMBER ADDRESS BF SIZE CR TIME LU TIME USE CNT The message is displayed as response to the command DS BFPOOL ALL A detailed statistic is displayed for the rvs internal bufferpool For each buffer of the bufferpool the current buffernumber the storage address the buffersize in bytes the time since creation of the buffer in seconds the time since last usage of the buffer in seconds and the usecount of the buffer is displayed in one row 27 rvsMVS Messages and Codes 5 rvs Messages STARTED DFO901I FTP TRACE TASK VERSION vvv dd mm yy tt mm STOPPED aa bb cc Start or end message of FTP Trace routine This program is started just after start of the FTP Main Task vvv specify version of FTP Trace Task dd mm yy tt mm time of assembly aa bb cc time of last changes in the FTP Trace Task STARTED DF0902P FTP TRACE FOR STATION sid sTOPPED A trace for an FTP station was started stopped DF0903E DYNAMIC ALLOCATION DEALLOCATION ERROR XXXX XXXX FOR FTP TRACE DATASET 2727222727222222222222 The message shows the error and info code of allocation deallocation of trace data set DF0904E ERROR DURING OPEN TRACE D
191. ization levels R sid REMOTE STATION NOT AUTHORIZED TO REPLACE DATA SETS A data set shall be received by station sid The transmitter specified for this data set that in case of an already existing data set of an equal dsname on receiving side this data set is to be replaced But the station sid is not authorized for this function The data set will be received in a normal way The specification made by the transmitter is to be ignored see rvsMVS Installation Manual for different authorization levels A replacement of the data set doesn t take place R sid 111 ERROR ON BLANK EXPANSION POSSIBLY REMOTE STATION SPECIFIED INCORRECT BLOCKSIZE An error occurred during expansion of compressed received data from station sid rvs internal compression of transmitted data May be the transmitting station sid specified invalid DCB attributes for this data set This is possible if the remote station works with the rvs DOS Monitor R sid nnn REMOTE JOB dsname NOT AUTHORIZED PROCESSING NOT STARTED The data set dsname from sid should be started as a job after reception remote JOB PROCESSING but the remote station is not authorized to use this function For a definition of station dependent authorization see rvsMVS Installation Manual description of rvs Stations Table parameter OPTIONS R sid nnn RECEIVED DATA COULD NOT BE CATALOGED RC xx The data set could not be cataloged For the reason see return code xx of the C
192. k2 and sense code If a VTAM request fails for the X 25 link Logical Unit the CTCP task will start termination rvsMVS Messages and Codes 5 rvs Messages DF9509W DF9510W DF95111 DF9512P DF9513W DF9514W DF9515I DF9516I DF9517P nn SESSION START REJECT NO VIRTUAL CIRCUITS AVAILABLE This message is issued by the rvs X 25 CTCP task in response to an operator Activate station command if no resources are available to handle a call request nn CALL REJECTED DUE TO INCOMPATIBLE FACILITY PACKET SIZE NAAR WINDOW SIZE This message is issued by the rvs X 25 CTCP task when a call setup is rejected due to incompatible X 25 packet or window size The values shown are taken directly from the call packet Please refer to X 25 documentation for further explanation nn CLEAR RECEIVED STATION CAUSE DIAG This message is issued by the rvs X 25 CTCP task when an X 25 Clear indication is received The message shows the X 25 clearing cause and diagnostic code For cause code and diagnosis code see chapter 6 of this manual nn CALL CONFIRM RECEIVED FROM STATION This message is issued by the rvs X 25 CTCP task when an outgoing call on the X 25 network has been confirmed by the calling address The called station is indicated in the message nn INCOMING CALL REJECTED NO RESOURCES AVAILABLE This message is issued by the rvs X 25 CTCP task when an incoming call on the X 25 network has been rejected b
193. lace If the error occurs again after a restart the data set must either be copied with a utility or re established Another cause of this error can be that the data set contains no data S sid RESTART COUNT EXCEEDS BLOCKNUMBER The data set contains less blocks than specified by the receiver during restart The restart is not possible no subsequent automatic restart takes place Another cause can be that the data set was re established in the meantime and the new data set is smaller than the original one f sid INCONSISTENT VALUES LRECL nnnnn LINEBLK rrrr This message appears only in connection with transmissions to non IBM computers A data set can t be transmitted because the length of the data record which is just transmitted is larger than the length of the available line buffer The maximum length of the line buffer is 2048 bytes so it is not possible to transmit data sets with a record length of more than 2048 bytes The current value of the station dependent line buffer length is defined within the rs Stations Table parameter LBLKSIZE see Installations Manual and may be modified with the command F sid SIZE nn see Operations Manual After this message the transmission is aborted with the user completion code 346 The status of the send request is changed from the active to the hold status So an automatic start or restart is prevented f sid DATA SET NOT FOUND ON SPECIFIED VOLUME The data set to be transmitted see
194. le R sid mn DATASET COULD NOT BE CATALOGED RC xx A dataset has been received from station sid The received dataset is an unloaded PDS which has been loaded successfully After this this PDS shall be cataloged but the catalog macro failed with returncode xx see for example the IBM manual OS VS2 SPL Data Management The transmission will be completed normally mn denotes the session SNA or the line address BSC which was used for receiption of this file R sid mn DATASET TO BE SCRATCHED IS NOT CATALOGED A PDS file has been received After receiving of the unloaded PDS the file has been loaded again The unloaded PDS is not longer needed and will be scratched But during scratch of this file it has been determined that this file is not cataloged Thus it can not be scratched This situation should normally never occur STATION ID MISSING WITHIN DIAL COMMAND The command DIAL sid has been entered But the required parameter sid id of station to be dialed has not been specified As a result of this the dial request will be ignored STATION ID sid NOT DEFINED WITHIN STATIONS TABLE The command DIAL sid has been entered But the specified value of sid id of station to be dialed is not defined within the rvs stations table The dial request will be ignored STATION ID sid NOT DEFINED FOR BTAM BSC LINES The command DIAL sid has been entered But there is no entry for station sid within the rvs stations table
195. lem has been detected nn OFTP TASK ABEND SID DSN 222 2222222222222222222222 This message is issued by the rvs XOT CTCP task when the ODETTE task EOT ECB has been posted DF9I60E XX XOT INITIALIZATION FAILED This message is issued by the rvs XOT CTCP task when initialization failed rvs XOT CTCP task will be terminated after this error 173 rvsMVS Messages and Codes 5 rvs Messages DF9I61I XX X text DF9I90P DF9I99P DF9I99P This message is issued by XOT task and contains additional information about XOT interface Wrong Parameters Allocation failed Open TCP IP socket failed Set TCP IP socket option failed Bind of TCP IP socket failed TCP IP listen failed TCP IP accept failed TCP IP receive failed TCP IP connect failed TCP IP socket close failed TCP IP send failed TCP IP gethostbyname failed X 25 wrong PacketType X 25 wrong called number X 25 wrong calling number Router Address not defined gethost failed wrong XOT header received not connected facilities were refused invalid facility values timeout occured called number unknown calling number unknown unknown error XXXXX If X 25 causes and diagnostics are available for the message the message is extended by X 25 cause XXX X 25 diagnostic XXX XX text This message is issued by the rvs XOT CTCP task when start of an XOT subtask failed nn xxxxxxxx The XOT Task issues this message This message is issue
196. les from different remote stations shall be stored in the same output file as specified in resident receive entries and the replace function is also used If this situation is detected the transmission will be cancelled and dynamic allocation error 0210 99 is used as error indication R sid acme sessid aaaaaaaa bbbbbbbb ccccccce dddddddd The message show allocation parameter for end file only for COMR SECR component aaaaaaaa file size in bytes hex bbbbbbbb BLKSIZE for end file hex cccccccc primary allocation for end file hex ddddddd secondary allocation for end file hex R sid WAITING FOR LIST OF RESIDENT RECEIVE ENTRIES The message is displayed if the monitor internal list of resident receive entries is not yet created available If this situation remains unchanged for more than one minute message DF1190P is changed to DF1190E to indicate an error situation It should be checked whether the receive dispatcher RDS controltask is active Activation of this controltask may be done by entering command A RDSP R sid RE READ FAILED RRsid dsn This message sid displayed if re read of a resident receive entry read from disk failed This situation may occure if a resident receive entry has been deleted but the monitor internal list of resident receive entries has not been refreshed since that time The message shows the remote station sid and virtual datasetname dsn of the affected entry R sid NON
197. location of these files or open processing failed in this case The monitor is no longer operational and thus terminated abnormally The dump of this abend should be kept for determination why the allocation or open was failing 340 154 This ABEND is coded in the program DF034K00 The code may occur if a the number of data set blocks of the data set to be transmitted could not be computed This may happen if the data set is not available The number of data set blocks is used in order to allocate space at the remote station for the data set to be received b the number of data set blocks exceeds a halfword count value of 65535 Reblock or split the data set 346 15A This ABEND is coded in the program DF034Mxx This code is related to Host non IBM computer transmissions The logical record length of the data set to be transmitted exceeds the maximum blocksize of the line buffer See message DF3412E 11 rvsMVS Messages and Codes 3 rvs Abend Codes 350 351 352 353 354 355 360 370 371 470 490 520 521 15E 15F 160 161 162 163 168 172 173 1D6 1EA 208 209 This ABEND is coded in the program DF035Kxx For this transmission rvs uses a protocol with data compression and sequence indication of the transmitted data set blocks The ABEND code indicates that the received data set blocks are out of sequence This ABEND is coded in the program DF035Kxx Aft
198. low 16 MB For this value the following formula is valid mmme rrr nnn So mmm is not the value for the size of unused virtual storage within the region of the rvs monitor This message is not displayed on console 39 rvsMVS Messages and Codes 5 rvs Messages Messages of the Initialization of Station table DF2200I DF2201W DF2203W DF2204W DF2205E DF2206E DF2207E DF2208W DF2209E x PROCESSING OF STATION TABLE STARTED First message of program DFO22B Processing of the Station Table allocated under DD Name STATIONS started WARNING INVALID KEYWORD AT ENTRY IGNORED A keyword of the mentioned station entry could not be recognized WARNING INVALID PARMVALUE AT ENTRY DEFAULT VALUE SET The specified parameter could not be recognized The default value has been set WARNING INVALID PARMVALUE AT ENTRY NO DEFAULT The specified parameter could not be recognized A default value could not be set ERROR RELAIS ENTRY NOT FOUND gt IND ENTRY FOR IGNORED U The Indirect Station Entry see Installation Manual chapter 6 2 1 has been ignored because a entry of the mentioned relay station has not been found ERROR RELAIS PARM MISSING gt IND ENTRY FOR IGNORED U The Indirect Station Entry see Installation Manual chapter 6 2 1 has been ignored because no relay station has been specified ERROR PPROF MISSING
199. m to station sid and access method acme DF5255P S sid acme nm REREAD OF RECORD NOT OK PUNKT 2 This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates that during selection of send request KD record was change for send session nm to station sid and access method acme DF5256P S sid acme nm PRIOR RESOURCE STILL IN USE WAIT FOR POST This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates internal problems within the rvs monitor for send session nm to station sid and access method acme Report this message to the system programmer DF5257P S sid acme nm SERIALISATION PROBLEM DON T SEND ENTRY This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates internal problems within the rvs monitor for send session nm to station sid and access method acme Report this message to the system programmer DF5259P S sid acme nm POSTCODE 4 BUT SESSION IS NOT DISPATCHABLE This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates internal problems within the rvs monitor for send session nm to station sid and access method acme Report this message to the system programmer 92 rvsMVS Messa
200. manent virtual circuits only Incompatible destination Network out of order DTE restarting Local procedure error Network congestion Network operational Registration cancellation confirmed 6 2 X 25 Diagnostic Codes 6 2 1 Diagnostic Codes from the DCE 00 No additional information Invalid P S Invalid P R Packet type invalid general For state Packet not allowed general Unidentifiable Call on one way logical channel Invalid packet type on PVC 187 rvsMVS Messages and Codes 6 X 25 Cause and Diagnostic Codes Packet on unassigned logical channel Reject not subscribed to Packet too short Packet too long Invalid GFI Restart with non zero GFI Packet type incompatible with facility Unauthorized interrupt confirmation Unauthorized interrupt Unauthorized reject Timer expired general Incoming call Clear indication Reset indication Restart indication Timer expired for call deflection Call setup problem general Facility code not allowed Facility parameter not allowed Invalid called address Invalid calling address Invalid facility length Incoming call barred No logical channel available Call collision Nonzero address length Nonzero facility length Facility not provided when expected Invalid ITU T specified DTE facility Maximum number of call redirections or deflections Exceeded Miscellaneous general Improper caus
201. me 72 rvsMVS Messages and Codes 5 rvs Messages DF37251I DATASET NOT CATALOGED xx The data set could not be cataloged after receiving For the information reason code xx see MVS ESA Authorized Assembler Programming Guide DATASET NOT SCRATCHED RC xxxx xxxxxxxx dsname The temporary data set could not be cataloged after start of reception For this reason the already allocated data set is to be scratched which did not end successfully For return and diagnosis codes xxxx xxxxxxxx see DFSMS MVS Diagnosis Reference DATASET NOT RENAMED RC xxxx xxxxxxxx dsname The temporary data set could not be renamed after reception For return and diagnosis codes XXXX XXXXXXXX see DFSMS MVS Diagnosis Reference dsname denotes the old data set name timestamp This message is followed by DATASET TARGET NAME dsname The message displays the new data set name of the failed rename DATASET GDG LOCATE RECOVERY NO NEW VERSION EXISTING The current GDG version could not be renamed cataloged rvs checks whether the current version of the GDG is still the highest version If the current version is not the highest version rvs determines the next new version and tries to rename catalog this new version This message displays that recovery by increasing of the version number is not possible DATASET ALREADY CATALOGED dsname The received data set could not be cataloged after reception because a data set with identical name
202. mmand with V mm number of queued send requests DF4907I x k k k SID NOT FOUND IN STATION TABLE This message is displayed after a DQ sid command if the station table of the running rvsMVS does not contain the station sid DF4908I sid nn vmm component component This message is displayed after the command DQ sid The message shows the number of active send requests nn for the station sid and the changes since last DQ Q command for the rvsMVS component component with v or for increase or decrease of the number of queued send requests mm number of queued send requests DF49101 FUNCTION NOT ACTIVE This message is displayed after one of the commands described in DF49031 and the component is not started DF5001 A Q DF5001 A Q DF5001 I Q DF5001 I Q DF5001 I Q DF5001 I Q DF5001 I Q DF5001 I Q f sid i dsname VOL volume status f sid i dsname QD yyddd QT hhmmsst st RE QT ddd hh mm ddd hh mm nnnnnn bbbb bbbMB P nnn ler er ser DS dsn ESTRT ddd hh mm RECL nnnnn RU uuuuuuuu TU uuuuuuuu JOB jobname CONV EXT OK ERR COMP EXT OK ERR SECR EXT OK ERR TRACE nn 81 5 rvs Messages or for increase or decrease of the number of queued send requests rvsMVS Messages and Codes 5 rvs Messages This message appears after different display commands The display of the parameters changes d
203. mounted or not online S sid mn RECORD LENGTH EXCEEDS BUFFER LENGTH TRANSMISSION NOT POSSIBLE The transmission of the queued data set shall be executed in an unblocked mode The record length exceeds the buffer size of 2000 bytes That s the reason why a transmission is impossible The data set will be placed in a HOLD status S sid mn DYNAMIC ALLOCATION ERROR ERR xxx INFO xxxx An error occurred during data set allocation For error reason code ERR and info reason code INFO see IBM manual OS VS2 MVS SPL Job Management S sid mn REMOTE STATION DOES NOT SUPPORT PDS TRANSFER FUNCTION A partitioned data set PDS is to be transmitted but the remote station does not support this function either the remote station has not installed rvsMVS or has installed an older release of rvsMVS which does not include this function The data set queued to station sid cannot be transmitted the send request for this data set is placed in the hold state S sid mn I O ERROR ON INPUT DATA SET NEW TRANSMISSION REQUIRED NO RESTART An error occurred during reading the indicated file A restart is not possible The file will be placed in hold status and must be created a second time S sid mn I O ERROR DURING RESTART POSITIONING NEW TRANSMISSION REQUIRED NO RESTART An error occurred during restart positioning of the indicated file No further automatic restart takes place The file will be placed in hold status and must b
204. mpletion The message shows the failing request and the VTAM return and reason code Refer to VTAM programming manual for further information This message should normally never occur This message is issued by the rvs APPC task manager routine when a VTAM request for APPC LU 6 2 is done The message shows the APPC command and qualifier CONT RCPRI SEC xxxx xxxx This message is issued by the rvs APPC task manager routine The message is issued as a continuation to a VTAM request info message for APPC LU 6 2 support The message shows the primary and secondary return codes and an associated text explanation PLU 7 777777 22727227227 RSN ACT LU 77777 This message is issued by the rvs APPC task manager routine The message is issued when a VTAM Attention exit is driven for the APPC support The message indicates the primary LU ACB for which the exit was taken the exit reason code and the logical unit LU that originated the exit Exit Exit reason description FMH5 An FMH 5 was received CNOS A CNOS request was received LOSS A session for a given partner mode is taken down PLU 2222222 RSN xxxxxx xx ACT LU CID This message is issued by the rvs APPC task manager routine The message is issued when a VTAM exit is driven in order to cause some action The message indicates the primary LU ACB for which the exit was taken Also indicated is the type of exit reason codes if available and the secondary
205. n f sid 111 TRANSMISSION OF dsn REJECTED BECAUSE OF EXIT DFUX001 see message DF1601E sid COMMAND NOT SUPPORTED This message appears if one of the commands M sid Q sid or R sid is entered and the remote station does not support the full rvs line procedure In this case the commands cannot be executed f sid 111 INVALID FEATURE XX IN A RECORD The feature bytes represents the transmission mode i e is compression to be performed or not between the actual transmitting and receiving station The transmission mode will be determined during the rvs protocol record exchange I A record exchange The reason for this message is an program error of the transmittin or receiving station f sid VOL nnnnnn NEEDED BUT CURRENTLY NOT REACHABLE The transmission stops because the monitor cannot access the volume nnnnnn because it is reserved by another CPU The transmission is continued as soon as the disk is released eng HAVE sid 111 b TEST RETURN CODE nnnn DSN dsname pEo luse J The occurence of ENQ and DEQ macros is listed for error analysis f sid 111 dsname FILE HAS ALREADY BEEN TRANSMITTED volume An entry of the control data set shows a complete transmission of the data set dsname R sid 111 RESPONSE QUEUED DSN data set name The response to the sender is generated after complete receiption of a data set f sid 111 text see message DF1602E sid 111 LINE I O ERROR SYNCHRONIZATI
206. n is an extract of the DATEX P Handbuch of the german Deutsche Telekom Fehlerhaftes Q Bit Einzelpaket nicht vereinbart Feld des Grundes ungleich 00 hex Nicht vertragliche Paketlange R ckweisung der Verbindungsanforderung PVC Servicedaten fehlerhaftt Ausl sung durch Operator Paket gt Annahme des Anrufs lt zu lang Verbindungsanforderung auf ankommend gerichtetem Kanal Verbindungsanforderung auf f r FVV reserviertem Kanal rvsMVS Messages and Codes 6 X 25 Cause and Diagnostic Codes Fehlerhafte Rufnummer des rufenden Anschlusses Ubermittlungsabschnitt unterbrochen Ubermittlungsabschnitt au er Betrieb Zeit berwachung f r den Zustand P1 abgelaufen Fehlerhaftes Feld des Grundes Fehlerhaftes Feld f r die Angabe von Leistungsmerkmalen Paket enth lt eine Adresse mit einer L nge ungleich Null Unerlaubtes Unterbrechungspaket Unerlaubte Unterbrechungsbest tigung Remarks The description of cause and diagnostic codes is quite short Therefore the following combination of cause and diagnostic codes may give a bit more information when problems occure This table contains some codes which have occured during operation of the X25 component of rvsMVS DIAGNOSTIC PACKET received Diagnostic Reason Code etree ed Possible Error Code hex hex 24 10 05 0B ee NPSI generation of your multi channel link or check compatibility with PTT generation too 10 05
207. n received which contains JCL This JCL has been passed to the internal reader for execution After this the JCL dataset is no longer needed and has been scratched If the data set could not be scratched the returncode yy and the status code zz of the scratch macro is displayed If the dataset has been scratched but not uncataloged the returncode xx of the catalog macro is displayed f sid mn sid2 dsname TIME OUT The transmisson of the data set identified by dsname will be terminated because a timeout situation has been detected During a time interval as specified for the session timer see description of the sessions table no data have been received on this session R sid mn SEND r RECORD FAILED SENSE xxxx yyyy see DF9105E R sid mn text see DF9106E R sid mn text The error message text has been received from the remote station Most times this message occures in conjunction with an abnormally terminated transmission of a data set R sid mn rvs PROTOCOL VIOLATION RECORD IGNORED A rvs record has been received from the remote station sid This record is not within the rooles of the rvs protocol The record will be ignored a just active data set transmission will be terminated R sid mn OUTPUT PROGRAM ERROR SYSTEM sss USER uuu TRANSMISSION CANCELLED 150 rvsMVS Messages and Codes 5 rvs Messages DF9315E DF9326P DF9329P DF9334P DF9334P DF9335P DF9336P
208. n to station sid has been interupted because no identification has been received from this station JCL DATA SET dsname NOT SCRATCHED RC xx A data set has been received which contains JCL After submission of the JCL the data set normaly has to be scratched In this case it could not be done because of return code xx xx is a return code of the SCRATCH Macro S sid 111 TRANSMISSION OF dsname REJECTED S sid 111 REMOTE STATION DOES NOT SUPPORT PDS TRANSFER FUNCTION The partitioned dataset with name dsname should be transmitted to station sid on line Ill During start of this transmission rvs detected that the remote station does not support PDS transfer As a result of this situation the dataset cannot be transmitted the send request is placed in hold state and for switched lines the line connection will be broken The send request for this dataset should be deleted because it cannot be assumed that the remote station will be able to support PDS transfer in the next time This function is supported only by stations which have installed rvsMVS release 1 0 or a following release A sid CONNECTION REJECTED ISTATUS INACTIVE A request for establishing a connection with station sid has been rejected because the stations entry is not released until now ISTATUS can be changed dynamically by the Operator see rvs Operations Manual if neccessary 107 rvsMVS Messages and Codes 5 rvs Messages DF56451I
209. named In case of GDG processing the jobstart is cancelled to avoid processing of the wrong GDG version DF5809I R sid JOB SUBMISSION WRITING OF EVENT ALREADY DONE SUPPRESSED NOW After reception of a dataset rvs checks whether a jobstart writing of event has already been done for this file In this case a second job submit will be suppressed This message indicates an interal error it should normally never occur DF5810W F sid WRITING OF EVENT SUPPRESSED BECAUSE OF FAILED RENAME After reception of a dataset from station sid the dataset could not be renamed In this case writing of event is suppressed to avoid processing of not existing file DF5811P R ORT LOG ENTRY LG FOR text DF5817I R ORT CONTINUE WITHOUT CHANGE OF JOB STATEMENT CARD DATASET OPEN ERROR Messages DF5811P until DF58171 are for possible error detection only They are not in effect for users purpose DF5812E F sid FIND FAILED RETCODE rc REASON rs HEX Error message in case of a failed FIND macro execution A FIND macro is used to locate a member in a partitioned dataset PDS Returncode rc and Reason code rs of the FIND macro are displayed in this message For details see the IBM manual DFSMS Macro Instructions for Datasets DF5813E F ORT JOBSUBMIT IGNORED BECAUSE OF INVALID DCB ATTRIBUTES Error message about an ignored job submit It is assumed that jobdatasets have fixed length records with a record length of 80 If this is not the
210. ne of the following user sense codes may occur Code Code decimal hexadecimal Meaning 001 001 An unknown or invalid rvs protocol record type has been received 002 002 A record of the Control Data Set has not been found 003 003 The data set to be transmitted is already running in another session 004 004 Invalid feature in H or A rvs protocol record 005 005 Violation of rvs protocol invalid sequence of rvs protocol records 006 006 Transmission cancelled by operator The data set is set in HOLD status 007 007 rvs block check characters of remote and local station are not equal 008 008 Invalid format of a rvs protocol record detected 009 009 Transmission cancelled The remote station wants to stop the session 010 00A Error during reading or writing data error in remote disk Input Output routine 011 00B Password not accepted by remote station 012 00C Password not accepted no exchange defined 013 00D Password is missing 014 00E Remote station does not support PDS transfer or load of a PDS failed in the receiving station 015 OOF File with identical name is already existing cataloged Receiving of this file is rejected 016 010 Transmission is rejected by exit Usually this exit checks whether an user is allowed to send or receive a data set access authorization 017 011 A wrong record count in header has been received 22 rvsMVS Messages and Codes 4 rvs Sense Codes 018 019 020 02
211. nnnnnnnnennn nun 3 5 FVS MESsages 2 sl 3 6 X 25 Cause and Diagnostic Codes ununnssnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnnn 3 6 1 X 25 Ca se Codes 2 5 se cvevnc veeecet eeee deanech os dk nos p das nets voeettne den aian inne un nern arendako Enean ences 3 6 1 1 Cause Codes within clear indication packet eee ce eeceeeeeeeeeeeeeeseneeeeeneeeeeees 3 6 1 2 Cause Codes within reset indication Packet cee cceseeeeeeeeeeeeeeeeeeeeeeseeeeeees 3 6 1 3 Cause Codes within restart indication packet uusesessnnsesnennnnesnennnnnen nennen en 3 6 2 X25 Diagnostic COde s enc seccccec encase s ctecestecce costenes nennen nase anna Easra oaiae daratan in 3 6 2 1 Diagnostic Codes from the DCE urur2nsnenennnnnnnnennnnnnnn nennen nenne nenn nnnnnnr nr 3 6 2 2 Diagnostic Codes from the DTE ceeccseseseeeeeseneeeeeesnaeeeeeseaeeeeeseaeeeeeneaeeeeaa 3 6 2 3 Diagnostic Codes from the network uneesennnensssnnnnnennnnnnnnnn nennen nennen nnnnnnn nn 3 T IVS Start Messages nn ai es 3 rvsMVS Messages and Codes 1 Introduction This page will be intentionally empty rvsMVS Messages and Codes 1 Introduction 1 Introduction This manual describes Messages User Sense Codes and Abend Codes of rvsMVS rvsMVS Messages and Codes 1 Introduction This page will be intentionally empty rvsMVS Messages and Codes 2 rvs User Codes 2 rvs User Codes
212. nored WARNING VIRTUAL STATION NOT INCLUDED IN CURRENT LICENCE KEY IGNORED FOR SID XXX WARNING TRANSFER RESTRICTION NOT INCLUDED IN CURRENT LICENCE KEY IGNORED FOR SID XXX The virtual station parameter STAT VIRT or transfer restriction TFR YES found in station entry for SID xxx but the virtual station or transfer restiction is not included in current licence key The parameter is ignored WARNING VIRTUAL STATION ONLY SUPPORTED FOR ACESS METHODS X25 LU62 TCP IGNORED FOR SID XXX The station parameter STAT VIRT found in station entry for SID xxx but the virtual station is available only for access method X25 LU62 and TCPIP The parameter is ignored WARNING USER STATIONS ONLY SUPPORTED FOR ACESS METHODS X25 LU62 TCP IGNORED FOR SID XXX The user stations parameter USR YES found in station entry for SID xxx but the user station is available only for access method X25 LU62 and TCPIP The parameter is ignored WARNING TRANSFER RESTRICTION ONLY SUPPORTED FOR ACCESS METHODS X25 LU62 TCP IGNORED FOR SID XXX The transfer restriction parameter TFR YES found in station entry for SID xxx but the transer restriction is available only for access method X25 LU62 and TCPIP The parameter is ignored WARNING USER LEVEL SECURITY SECURITY ONLY SUPPORTED FOR ACESS METHODS X25 LU62 TCP IGNORED FOR SID XXX The ULS user level security ULS YES found in station entry for SID xxx but the user level security
213. not be found in the sessions table See rvsMVS Installation Manual Generating the STATIONS SESSIONS table INVALID MODE x FOUND IN SESSION PROFILE sss The sessions profile sss contains an invalid sessions type x SESSION TABLE ESTABLISHED After start of the rvs Monitor the session table has been created incore As a model for this table member SESSIONS of the rvs Tables Data set is used in conjunction with the rvs Stations Table ERROR SPROF NOT FOUND gt ENTRY FOR SID IGNORED The mentioned Station Entry has been ignored because incorrect session profile parameter has been specified TOTAL NUMBER OF INTERNAL STATION TABLE ENTRIES The number of internal station entries has been decreased INVALID PARM VALUE Error in the parm entry of the program DF024A00 This program copies a received data set to a tape or into a SYSOUT CLASS or a data set which is to be transmitted to disk The entry in the member RTAPEJC SYSOUTJC or STAPEJC of rvs TABLES may not be in the right column position of the line INVALID INPUT DATA SET NAME The name of the input file of the program DF024A00 is invalid See also message DF2401E INVALID OUTPUT DATA SET NAME The name of the output file of the program DF024A00 is invalid See also message DF2401E INVALID INPUT VOLUME SERIAL NUMBER The volume number of the input file of the program DF024A00 is invalid See also message DF2401E RE READ OF THE KD RECORD FAILED U
214. ns receiving of this file will be rejected DF3739E R sid EXTENSION OF dsname FAILED The data set dsname is to be received from station sid For the reception of the file the replace function is active this means an already existing data set with this name is to be replaced by the new data set for example the replace parameter has been specified within a resident receive entry But the space allocated by the already existing file is not sufficient to store all data of the new file In this case rvs tries to extend the already existing file allocation of a new file on the same disk with a new name deletion of the existing file renaming of the new file but the extension failed As a result of this error reception of the file will be rejected The file can be received only after the already existing file has been extended This message is preceded by message DF2701P which contains more information about the kind of the error probably allocation error not enough space for the new extended file 75 rvsMVS Messages and Codes 5 rvs Messages DF3742E R sid mn ESTAE RECOVERY FOR ABEND code DSN dsname A file with the name dsname is to be received from station sid An abend code has occurred e g system abend B37 or D37 This abend will be recovered by normally termination of the transmission A dump will not be written for the abend DF3744I R ORT MO text DF3745P R ORT MO 00010203 04050607 O809
215. nsmission speed since the start of transmission of the current data set The precision of the speed determined largely depends on the duration of the transmission DISPATCHER SUBTASK STILL ACTIVE The command A DSP has been entered to start the dispatcher subtask The message indicates that this task is still active the command will be ignored f sid PROGRAM PROFILE NOT FOUND LINE ASSOCIATION TERMINATED Error in the definition of the station table or in the definition of the program profile table xvsVTAM y rvsx25 SNAP DUMP TAKEN sid 111 lrmop J A SNAP DUMP has been taken either for the VTAM control task X25 control task Remote Operator control task or for the BSC line control task of station sid line Ill A sid NO LINE AVAILABLE 53 rvsMVS Messages and Codes 5 rvs Messages DF3030E DF3031I DF3032I DF3033I DF3034I DF3035I DF3036A DF3037I DF3038I The command A sid has been utilized for activation No station related line of the lines which are specified in the STATIONS member of the rvs TABLES data set is available A sid nnn REQUESTED LINE NOT ASSOCIATED The command A sid nnn has been utilized for activation The line nnn which is specified in the activate command is not available and could not be associated A sid LINE nnn ASSOCIATED During activation of the station sid this station was associated with line nnn T sid nnn TRACE STARTED
216. nsmitted DF5903E S sid UNEQUAL BLOCK NUMBER S sss R rrr sss blocks have been transmitted and rrr blocks are confirmed by the receiver In order to eliminate the error all active control data set entries at the receiver and transmitter which relate to the data set in question must be deleted This can be done by entering the commands D sid S dsname D sid R dsname In order to get confirmed the deletion enter the commands N sid Q name or N sid R name The data sets to be transmitted must be queued again If the error occures again there is a programming error DELETED DF5907W S sid dsname NOT 4 m re lUNCATLGD After transmission of a data set this data set should be deleted or uncataloged The following errors Can occur 111 rvsMVS Messages and Codes 5 rvs Messages UNCATLG nn 08 data set was nor cataloged 28 error in catalog DELETED nn 08 rc 01 data set is not located on specified volume 02 data set is protected by PASSWORD 03 expiration date has not yet expired 04 1O error 05 volume is not mounted 06 amass storage volume could not be mounted 07 data set is still required by another job 08 the monitor is not authorized to erase an RACF protected data set 09 RACF error nn 12 rc 00 programming error DF6101I R sid mn LOAD OF PDS COMPLETE VOLUME volume A dataset has been received from station sid The received dataset is an unloaded PDS which must be loaded again This message indic
217. nsmitter specified that in case of an already existing data set with equal data set name on receiving station this data set is to be replaced But the station sid is not authorized to do this The data set will be received normally In case of an already existing data set with equal data set name this data set is not replaced For a definition of station dependent authorization see Installations Manual description of the rvs Stations Table parameter OPTIONS R sid mn DSN dsname CANCELLED Receiving of the data set dsname has been cancelled by operator R sid mn RESTART DATA SET FOR dsname NOT AVAILABLE The data set dsname is to be received by station sid The transmission is a restart The data set allocated during an earlier transmission is not available The reason for this may be e the data set is not disk volume 74 rvsMVS Messages and Codes 5 rvs Messages e the disk volume is not mounted The try to restart the transmission will be cancelled and the restart count is set to zero This causes that the next transmission request is not a restart DF3735W R sid mn NONZERO RETURN CODE OF INSTALLATION EXIT DFUX001 Execution of the installation exit DFUX001 ended with a nonzero returncode One of the following two messages with more information is also displayed in conjunction with this message DF3735W R sid mn ONLY INSTALLATION STANDARDS WILL BE USED TO RECEIVE dsname The data set dsname has to
218. o DF2540A the operator entered YES that means that the data set is to be scratched and uncataloged if the data set is still cataloged This message indicates that the data set is not cataloged Thus it can not be scratched or uncataloged The send or receive entry however is deleted D sid NN ACTIVE ENTRIES FOUND After input of the command D sid S R all NN entries were found This message is followed by DF2590l D sid CONFIRM DELETE REQUEST DEL OR NO After input of the command D sid S R ALL and display of message DF2580I rvs is asking for a confirmation to delete all specified entries Following replies are possible DEL Entries will be deleted NO Entries will not be deleted R sid DS EXTENSION CODES aa bb cccc dddd ee gggg hhhh ii jj kk 11 mm nn During reception of a file an already existing data set with the same name is to be replaced replace function During start of reception rvs checks whether the already existing file has sufficient space to store the file to be received If the already existing file does not contain enough space rvs tries to extend this file allocation of an extended new file on the same disk volume with new name deletion of the old file rename of the new file This message indicates various error codes which may occur during these activities During checking whether there is enough space the following codes are used aa returncode reg 15 of obtain macro read form
219. o be transmitted is on disk the operator is provided with the possibility of physically scratching the data set from disk after message DF2520I Possible replies are YES The data set is to be scratched NO The data set is not to be scratched DF2550I D sid DATA SET NOT SCRATCHED RC xx yy REQUEST CANCELLED After input of YES in response to DF2540A the data set could not be scratched because of an error The following information xx Return code yy Scratch status code is explained in the IBM brochure OS VS2 SPL Data Management SCRATCH macro DF2560I D sid REQUEST CANCELLED In response to DF2510A the operator entered END The request is cancelled DF25651I D sid DELETE REQUEST NOT SUCCESSFULL In response to DF2590A the operator entered DEL An unexpected error occurred while processing the delete request DF2570I D sid DATASET NOT UNCATALOGED RC xx 47 rvsMVS Messages and Codes 5 rvs Messages DF2571I DF2580I DF2590I DF2701P DF2702P In response to DF2540A the operator entered YES that means that the data set is to be scratched and uncataloged if the data set is still cataloged This message indicates that the data set could not be uncataloged xx denotes the returncode register 15 in decimal of the CATALOG macro For a description of this returncode see for example the IBM manual OS VS2 SPL Data Management D sid DATASET TO BE SCRATCHED IS NOT CATALOGED In response t
220. ocol record type r is listed on printout R sid FIRST STATION sid ORIGINATOR IS NOT DEFINED IN STATIONS TABLE A data set is to be received from a remote station Originally it comes from a third station sid but this station id is not defined in the local stations table The receiving of this dataset ist rejected F ORT MO MAXIMUM ERROR RETRIES REACHED FOR DSN name The maximum error retries reached for dataset The transmission will be cancelled 151 rvsMVS Messages and Codes 5 rvs Messages Messages of the ODETTE FTP task All message identifiers produced by the ODETTE FTP task are of format DF94xxn If the messages are issued from the X 25 component the message id is followed by the number of the rvs X 25 CTCP e g DF9401P 05 F sid accm sessonid ODETTE TASK STARTED TYPE type LEVEL level In this case the message belongs to CTCP No 5 DF9401P F sid accm sessonid ODETTE TASK STARTED TYPE type LEVEL level This message is issued by the Odette File Transfer Protocol task when task initialization is complete Shown is the task type which can be INITIATOR RESPONDER a station has been called by rvs in response to an Activate station command an incoming call has been received over the network DF9402P F sid accm sessonid ODETTE TASK STOPPED This message is issued by the Odette File Transfer Protocol task when task termination is complete DF9403I Z sid accm sessonid TIME OUT OCCU
221. of the incore rvs sessions table The dump output of these commands is written as print only message message identifier DF1232P to the resource allocated with DD name SYSWTOxx to the rvs monitor depending on the content of member MSGIDxx of the rvs tables data set or to the resource allocated with DD name Y nnnnn number of Y command text 32 rvsMVS Messages and Codes 5 rvs Messages DF1233E DF1234E DF1237I DF1241W DF1242E DF1242W DF1243P This message contains data which have been created by one of the commands Y STATIONS dump of the incore rvs stations table Y SESSIONS dump of the incore rvs sessions table The listing of rvs internal controlblocks may be useful in case of problem determination SESSIONS TABLE DOES NOT EXIST The command Y SESSIONS has been entered This message indicates that the rvs internal sessions table does not exist and that this table cannot be dumped STATIONS TABLE DOES NOT EXIST The command Y STATIONS has been entered This message indicates that the rvs internal stations table does not exist and that this table cannot be dumped should not occur error xxx Y FILE ACTIV The Y command has been entered Results of realize this command is written to Y file NOT CATALOGED F sid dsn NOT UNCATALOGED RC xx yy NOT SCRATCHED J A successfully sent data set should be deleted uncataloged resp a successful received data set should be
222. omputes a BCC and compares both If the remote and local computed BCC are not equal this message appears at the receiving local station The line block will be transmitted once more III line address XXXX block check character of the transmitting station yyyy block check character of the receiving station 104 rvsMVS Messages and Codes 5 rvs Messages DF5616P DF5617P DF5618E DF5619E DF5620P DF5621A DF56221 DF5623A text first bytes of the line block in hex f sid 111 RVI SENT In some cases the receiving station sends a RVI sequence if the transmission is cancelled by operator or if an error occures in the receiving subtask f sid dddd xxxx TEXT yyy After line faults the DECB xxxx and the start ofthe data area yyyy for the line is indicated dddd indicates a displacement to the beginning of the line control program NEGATIVE ACK f sid 111 TIMEOUT b LOST DATA LINE I O ERROR RETRY A CONNECTION The transmission of a block is faulty in spite of repeated attempt The data connection is interrupted If the error occures several times the connection should be redialed on switched lines NEGATIVE ACK The remote station indicates the reception of a faulty block TIMEOUT The remote station does not answer LOST DATA The control unit has received more data than expected If this occures frequently the control unit is probably incorrectly generated LINE I O
223. onse to a previously issued X 25 Clear request 164 rvsMVS Messages and Codes 5 rvs Messages DF9518P DF9519E DF9520I DF95211I DF9522W DF9523W DF9524E DF9525W nn CONFIRM RECEIVED ON SESSION This message is issued by the rvs X 25 CTCP task when an X 25 Clear or Reset confirmation is received on an active session The message shows the Logical Unit name and the station id of the virtual circuit on which the confirmation was received nn ERROR REPORTED FOR VC COMMAND REASON This message is issued by the rvs X 25 CTCP task when an error information packet is received from the IBM NPSI product The message shows the virtual circuit that had the error the command in error and the associated reason code The corresponding virtual circuit will be closed nn RESET FOR PERMANENT VIRTUAL CIRCUIT RECEIVED CAUSE DIAG This message is issued by the rvs X 25 CTCP task when an X 25 Reset packet is received from the IBM NPSI product The Reset is associated with a permanent virtual circuit that is currently not connected For cause code and diagnosis code see chapter 6 of this manual No further action is taken for this type of packet nn PAD DATA RECEIVED FOR MESSAGE This message is issued by the rvs X 25 CTCP task when a data packet with the Qualified Data Indicator is received A Qualified Data packet is a so called PAD message and the type of PAD message is sho
224. pter 6 DF1902E ERROR NEAR PARAMETER parm Identification of the parameter parm is in error DF1903W VOLUME AND UNIT PARAMETER SPECIFIED UNIT PARAMETER IGNORED The rvs start parameters VOLUME is exclusive with the UNIT parameter see rvsMVS Installations Manual This message is issued to indicate that the UNIT parameter will be ignored DF1904E INCOMPLETE PARAMETER SPECIFICATION FOR X25 SNA TCP IP COMPONENT DF1904E X25 SNA TCP IP COMPONENT nnnnn OF RVS CANNOT BE USED The rvs start parameter X25USE YES SNAUSE YES or TCPUSE YES has been specified or is used as a default value In this case some other rvs start parameters concerning the specified component of rvs are mandatory But at least one of these parameters has not been specified As a result of this the specified component cannot be used same processing as if X25USE NO SNAUSE NO is specified See rvs Installations Manual description of the rvs startparameter X25USE SNAUSE or TCPUSE for more details In case of X25 or TCP IP nnnnn specifies the number of the CTCP X25 or the stack number TCP IP which cannot be used DF1904E COMPLETE X25 TCP IP COMPONENT CANNOT BE USED The message shows that the definition of all specified CTCPs X25 or all specified IP stacks TCP IP are incomplete DF1905E OWN STATION ID REQUIRED This message appears if the own station id is missing in the rvs start parameter specif
225. put data set could not be transmitted or if an error occurs during execution of the RDJFCB macro or if the OPEN of the input or output data set fails This ABEND is coded in the program DF072A00 PDF0014A This abend indicates that the rvs Control Data Set is damaged The rvs Control Data Set must be recovered Procedure PDF0015A Before running Procedure PDF0015A the SHAREOPTIONS Parameter used for definition of the Control Data Set should be checked the value must be SHR 4 3 This ABEND is coded in the program DF072A00 Open error in module DF172A00 PDFO015A This ABEND is coded in the program DF072A00 VSAM error in module DF173A00 PDFO015A 18 rvsMVS Messages and Codes 3 rvs Abend Codes 1733 6C5 This ABEND is coded in the program DF073A00 Open error in module DF173A00 PDF0015 lt A 1734 6C6 This ABEND is coded in the program DF073A00 This ABEND occurs in different situations if the OPEN of the KDSAVE or KD data set fails or if the VSAM PUT macro fails or if the data set KDSAVE is empty or if the OPEN of the data set rvsLOG fails 1790 6FE This ABEND is coded in the program DF079C00 The program DF079C00 initialization or reorganization the control data set has been executed The error occurred during checking the PARM string 1791 6FF This ABEND is coded in the program DF079C00 The program DF079C00 initialization or reorganization the control data set has been executed The error occurred d
226. r X25SESS in station table for sid nn ACTIVATION FOR STATION sid REJECTED NO RESSOURCES AVAILABLE The message occurs if the command A sid for a X 25 station has been entered and all SVCs of the CTCPs which are defined for the specified station are in use nn ACTIVATION FOR STATION sid REJECTED SPECIFIED CTCP NOT DEFINED FOR THIS STATION The message occurs if the command A sid Cnn for a X 25 station has been entered but the specified CTCP number is not defined for this station See definition of parameters X25GROUP and X25NUM in Installations Manual CTCP COMMAND REJECTED SPECIFIED NOT DEFINED TCP IP STACK The message occurs if a command which includes a specification of an X 25 CTCP TCP IP control task has been entered e g A RVSX C1 or A RVST C10 and the specified CTCP number TCP IP stack number is not defined see rvs start parameters member CNTL of the tables data set Installations Manual SPECIFIED CTCP NOT ACTIVE nn 4 b wor READY TCP IP CONTROLTASK ALREADY ACTIVE The message occurs if a command which includes a specification of an X 25 CTCP TCP IP controltask has been entered e g A RVST C1 or P RVST C10 and the specified CTCP TCP IP controltask is e not active e not ready to process an operator command at this time e already active REFRESH OF STATION RECORDS STARTED LEVEL date time During start of the rvs monitor and during execution of the refresh fo
227. r received direction and the dataset name dsn DF85731 D sid sesid VOLUME volser IS NOT MOUNTED The FTP Server Task issues this message if the volume containing the file is not mounted DF8574I D sid sesid FILE filename NOT FOUND ON SPECIFIED VOLUME The FTP Server Task issues this message if the file is not found on the volume specified in the KDRECORD Shown is the virtual file name DF8575I D sid sesid PHYSICAL DSN filename VOLUME volser The FTP Server Task issues this message if the file is not found on the volume specified in the KDRECORD Additional this message shows the physical dataset name of the file DF8577I D sid sesid dsn NOT CATALOGED The FTP Server Task issues this message if the dataset to send is not found DF8581P D sid sesid WORK FILE name EXIST The FTP Server Task issues this message when the FTP control file is found For internal use only DF85831I D sid sesid DECODE OF HD FILE ID FAILED KDCOMLP nnnnnnnn The FTP Server Task issues this message when verification of HFID records ended with error The following list describes the different reason codes 0136 88 Duplicate file 0152 98 Real work file not exist 0160 A0 Invalid syntax 0164 A4 Invalid origin 0168 A8 Invalid destination 0172 AC Maximum record length not supported 0176 B0 File already catalogued 0180 B4 Unspecified reason DF8584P D sid sesid text nnnn cc VOL volser DSN dsn The
228. r the stations table rvs command REFR STAT a refresh of the station records whithin the rvs control dataset is done The station records include station depentent information and are used for checks when send requests are created module DFO80A00 LEVEL indicates the assembly date and time of the refresh module REFRESH COMPLETE NEW nl DEL n2 UPD n3 TOTAL n4 Refresh of the of the station records whithin the rvs control dataset is complete The message displays the number of inserted deleted and modified records as well as the total number of station records REFRESH OF STATION RECORDS ALREADY ACTIVE NOT EXECUTED Refresh of the of the station records whithin the rvs control dataset is just executed by another rvs monitor whithin the installation In this case a second parallel refresh is not executed 60 rvsMVS Messages and Codes 5 rvs Messages DF3301I DF3302I DF3303I DF3304I DF3305I DF3306E DF3307P DF3308P DF3309P DF3400I DF3401A f sid NO DATA SET dsname QUEUED In the commands H sid or S sid a data set with the name dsname was specified for which no transmit request has been stored S sid ENTER VOLUME NO OF DATA SET TO BE RETRANSMITTED OR END After entry of the command S sid name the operator is asked for the volume number f sid NO ENTRY dsname volume PROCESSED This message is a response to the command S sid An entry of control data set assigned to
229. renaming it back to its temporary name an error occurred For return and diagnosis codes xxxx xxxxxxxx see DFSMS MVS Diagnosis Reference The dataset will reside uncataloged under its final name on disk DATASET NOT UNCATALOGED dsname 139 rvsMVS Messages and Codes 5 rvs Messages The temporary dataset with timestamp dsname has been renamed to its final name but could not be uncataloged DF88Y4P KDUPDAT 88Y TYP This message is issued by the FTP task List internal action of FTP task with KD control file For internal use only STARTED DF8900I FTP MAIN TASK 4 VERSION vvv sTopPED dd mm yy tt mm aa bb cc Start or stop of FTP Main Task message vvv specify version of FTP Main Task dd mm yy tt mm time of assembly aa bb cc time of last changes in the FTP Main Task DF8903E FTP ABEND CODE EP PSW This message is issued by the FTP Main task when an abend occurs The message shows the system abend code the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done after all subtasks have been terminated DF8904I REGS 0 7 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX KXXXXXXX XXXXXXXX XXXXXXXK XXXXXXXX This message is issued by the FTP Main task when an abend occurs The message shows the content of the registers 0 to 7 at the time of abend DF8905I REGS 8 15 xxxxxxxx XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXKXXXXX XKXXXX
230. river task routine The APPCCMD REJECT was issued to stop a conversation with a partner node but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information APPCCMD RECEIVE FAILED FOR RC xxxx SENSE xxxx This message is issued by the rvs APPC driver task routine The APPCCMD RECEIVE was issued to read data on a conversation but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information APPCCMD SEND FAILED FOR RC xxxx SENSE xxxx rvsMVS Messages and Codes 5 rvs Messages DF8714W DF8715W DF8799P This message is issued by the rvs APPC driver task routine The APPCCMD SEND was issued to send data on a conversation but the request failed In the message is shown the VTAM return and sense codes for the failing request Refer to VTAM programming manual for further information rvs APPC DRIVER SEND DATA FLUSHED DUE TO LOCKED SERVER QUEUE This message is issued by the rvs APPC driver task routine when data to be sent to the file protocol server was rejected due to a locked server queue ie the file server was not ready to accept the request F sid APPC DRIVER SHUTDOWN because of secondary CANCEL starting This message is issued by the rvs APPC driver task routine when a shutdown request s
231. rnal station entries is higher than the number of remote stations because rvs creates one entry for every subchannel definition and one entry for every backup station defined by BCKP ERROR LU62MODE MISSING NO DEFAULT gt ENTRY FOR SID sid IGNORED U The mentioned Station Entry for a LU6 2 station has been ignored because no LU62MODE parameter has been specified and no default LU62MODE in the CNTL member has been specified too ERROR LU62MODE MISSING NO DEFAULT ERROR LU62MODE MISSING NO DEFAULT WARNING INVALID PARMVALUE pppppppp vvvvvvvv HEX PAIRED NECESSARY gt VALUE FOR SID sid IGNOREDU The value for the specified parameter should be hex paired ERROR TO MANY rvsWIN STATIONS YOUR LICENCE ALLOWS ONLY nnnnn INSTALLATIONS gt ENTRY FOR SID sid IGNOREDU The station contents table are more rvsWIN stations than your licence key allows The following rvsWIN stations will be ignored Please contact your software distributor WARNING INVALID INDEX xxxxxxxxxxxx AT ENTRY sid IGNORED The parameter s index is invalid outside of 1 99 or contents other characters than 0 9 WARNING INVALID PARMVALUE pppppppp vvvvvvvv HEX DESCRIPTION REQUIRED gt VALLUE FOR SID sid IGNOREDU The parameter requires hex description but the specified value includes other characters than 0 9 A F WARNING INVALID PARAMETER pppppppp vvvvvvvv SID IS NOT DEFINED FOR X 25 gt VALUE FOR SID si
232. roken f sid 111 CONNECTION CANCELLED BECAUSE OF EXIT name An Identification User Exit is installed name denotes the loadname of the exit This exit controlls the identification phase which is performed after the line connection dialling is established The exit returned a nonzero returncode to rvs as a request to break the line connection This message is followed by message DF5514E F sid CONNECTION REJECTED ISTATUS INACTIVE A request for establishing a connection with station sid has been rejected because the stations entry is not released until now ISTATUS can be changed dynamically by the Operator see rvs Operations Manual if neccessary F LLL UNACCEPTABLE FUNCTION CODE TO INITIATE I O INTERFACE Line driver call for I O interface with an invalid function code The request cannot be processed and the connection will be terminated User action none contact software distributor Messages of Line Control Program DF056B00 DF5600M DF5601A DF5602E DF5603E DF5604P xf sid 111 message text A message has been received from station sid This message is displayed on console sid EXPECTS dsname DATA SET NOT FOUND The operator of the remote station sid wants to receive the data set dsname However this data set has not been queued for transmission The causes can be e data set has not yet been established e control data set update has no yet been run e data set has already been transmitted b
233. rom the date information D sid sesid FTP message D sid sesid UNEXPECTED END OF FTP OUTPUT FILE D sid sesid FTP CONNECTION REJECTED D sid sesid FTP SESSION REJECTED 7 D sid sesid TRANSMISSION CANCELED D sid sesid FTP FUNCTION ERROR D sid sesid VERIFY FTP RETURNCODE nnnn The FTP Server Task issues these messages by checking FTP output file Appropriate set of messages DF8560E DF8568E show corrected or not corrected flow FTP connections during transfer of rvsMVS FTP file If FTP returncode is equal 04 or 08 the FTP connection ended with error see rvs log messages D sid sesid UN ALLOC FAILED nnnn mm VOL volume DSN dsn The FTP Server Task issues this message when an error occurs during allocation or unallocation of a dataset In the message is shown the return code from the allocation request and the volume and dataset name of the file for which the error occurred D sid sesid OPEN FAILED FOR VOL volume DSN dsn The FTP Server Task issues this message when a dataset to be send or received could not be opened In the message is shown the volume and dataset name of the file for which OPEN error occurred D sid sesid SUCCESSFUL FILE TRANSFER direction FILE dsn 127 rvsMVS Messages and Codes 5 rvs Messages The FTP Server Task issues this message when a file transfer has been successfully completed In the message is indicated whether the dataset was send o
234. rs The message shows the system abend code the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done after all subtasks has been terminated This message is issued by the rvs X 25 CTCP task when a VTAM exit has been scheduled The message is only issued if trace for the X 25 link Logical Unit is active unless the TPEND exit is scheduled Scheduling of the TPEND exit will always be reported nn ACB OPEN FAILED ACB RSN This message is issued by the rvs X 25 CTCP task when open of the ACB to use for VTAM communication fails The message shows the ACB name the reason code for open failure and an explanatory text The CTCP task will terminate when the ACB cannot be opened nn ACB CLOSE FAILED ACB RSN This message is issued by the rvs X 25 CTCP task when close of the ACB used for VTAM communication fails The message shows the ACB name and the reason code for close failure The CTCP task will continue termination This message is issued by the rvs X 25 CTCP task when a VTAM SETLOGON request fails The message shows the SETLOGON type START STOP and the VTAM return code The CTCP task will terminate if SETLOGON START is not successful nn FAILED FOR LU REASON rrff SENSE This message is issued by the rvs X 25 CTCP task when a VTAM request fails The message shows the failing request the Logical Unit that issued the request and VTAM return rr rtncde ff fdb
235. s a reply to the command X sid S the sessions profile used by station sid alias sid2 is listed see section 4 4 4 NON X sid TO b BACKUP FOR sidk sidm lsidl sidn As a reply to the command X sid RELAIS the next connected stations to station sid will be listed In case of no next connected stations are specified for station sid the word NON appears Stations which can be reached in case of a backup situation via station sid will be listed behind the parameter BACKUP FOR see section 7 6 3 79 rvsMVS Messages and Codes 5 rvs Messages Messages of the DQ command DF4901I DF49021I DF4902I DF4903I DF4903W DF49041I sidl nn sid2 nn sid3 nn sid4 nn sid5 nn sid6 nn sid7 nn The number for outstanding send requests is indicated for each station sid This message is displayed after start of the rvs Monitor it is displayed again if the number of send requests has changed or if the command DQ has been entered NO QUEUED SEND REQUESTS or nnn QUEUED SEND REQUESTS This message is displayed as a response for the command DQ If no outstanding send requests are found in the control data set the first message is displayed If send request have been found message DF4901 or DF4906I or DF4908I will be displayed The end of this display is indicated by the above message which shows the number of all send requests in summary kkkkkk message string kkkkkk This m
236. s are used or not and the DIRECTION Starting with rvsMVS Rel 2 5 the COMPRESS value indicates the highest compression level possible between both partners The current compression level for one file transfer will be shown by message DF9492P DF94231 F sid accm sessonid OFTP TASK ABEND CODE cde EP entry point PSW prog stat word This message is issued by the Odette File Transfer Protocol task when an abend occurs The message shows the system abend code associated with the task the entry point of the program and the address where the abend occurred When an abend occurs task termination will be done DF9424I Z sid accm sessonid SUCCESSFUL FILE TRANSFER direction FILE dsn This message is issued by the Odette File Transfer Protocol task when a file transfer has been successfully completed In the message is indicated whether the dataset was sent or received direction and the dataset name dsn DF9425W F sid accm sessonid task name SEND DATA FLUSHED DUE TO LOCKED SERVER QUEUE This message is issued by the Odette File Transfer Protocol task when data to be sent to the network server was rejected due to a locked server queue ie the nerwork server was not ready to accept the request In the message is indicated the task name DF9426E F sid accm sessonid TOO MANY ERRORS DETECTED SESSION WILL BE TERMINATED This message is issued by the Odette File Transfer Protocol task when an internal limit of error numbers has exceeded
237. s driven by the TCP IP address space The TCP IP address space has terminated RC shows the invocation reason of the event 1 TCP IP address space has terminated TCPEND 2 TCP IP address space has terminated the connection to the user TCPCONEND 4 Other call the IBM support center LOCAL IP ADDRESS TCPLOCAD ipaddress INVALID This message is issued during start of the rvs TCP IP control task The specified local ip address parameter TCPLOCAD is not valid for this host bind error number 49 The TCP IP control task will terminate after this error OFTP TASK ABEND cde SID sid DSN dsname This message is issued by the rvs TCP IP task when an OFTP task has been terminated abnormally Cde denotes the abend code system or user completion code Further the 120 rvsMVS Messages and Codes 5 rvs Messages DF8338E DF8339E DF8340E DF8342I1 related station id sid and the dataset name dsname of the abended transmission are displayed JES ALLOCATION PROBLEM A hang up situation has been detected The reason for this situation is an allocation request which does not complete If this situation does not change whithin some minutes the rvs monitor should be stopped and started again LOCAL IP ADDRESS NOT RESOLVED This message is issued by the rvs TCP IP task during initialization of the task Parameter TCPLOCAD has been specified with a DNS Name This name could not be resolved by the domain name service The TC
238. s function is supported only by stations which have installed rvsMVS release 1 0 or a following release DF5801I R sid dsname member SUBMITTED JNM name number A data set has been received from station sid After reception of the file the data set dsname member has been submitted automatic jobstart after receiving member and number denote the name and number of the submitted job dsname member DF5802I R sid SUBMIT OF 4 FAILED RC xx ldsname J After reception of a data set from station sid the data set dsname or the member member of the PDS dsname should have been submitted During this action an error occurred The JCL could not be submitted The following returncodes hex may occur 04 The data set dsname was not allocated or could not be allocated 08 The member member does not exist in the PDS dsname OC Error during accessing the internal reader or the data to be submitted have not a recordlength of 80 or exit DFUX003 could not be loaded 10 Execution of exit DFUX003 ended with a returncode of 12 dec or higher 14 The data to be submitted are not a valid job This means the first card s of the data to be submitted are not JES3 comment cards starting with and not a valid job card starting with name JOB where name is any valid jobname DF58031 R sid text text is a message of the user exit DFUX0003 DF5804I R sid ALLOCATION OF JOB DATA SET FAILED ERROR xxxx yyyy
239. s the maximum block size used for 3330 disks The data set is transmitted anyway DF3421E S sid DATA SET EXCEEDS MAXIMUM BLOCK NUMBER TRANSMISSION TERMINATES The data set to be transmitted contains more than 65 535 blocks The transmission is cancelled with return code X 34 UN ALLoC DF3502E R sid DYNAMIC ERROR xxxx yyyy ALLOCATION A data set shall be has been received from the rvs station sid The output data set could not be allocated unallocated For significance of XXXX Error reason code yyyy Information reason code see IBM brochure OS VS2 System Programming Library Joo Management DF3504E R sid NO ACTIVE CONTROL RECORD FOUND RESTART IS IMPOSSIBLE An automatic restart took place but the appropriate record in the control data set has been deleted in the meantime Transmission must be restarted by R sid dsname DF3505E R sid REQUIRED VOLUME volume IS NOT MOUNTED 63 rvsMVS Messages and Codes 5 rvs Messages DF3506E DF3507A DF3508E DF3509E DF3510E REQUIRED DF3511E DF3512E The volume indicated in this message must be mounted for transmission of a data set If this disk volume does not exist the corresponding resident receive record must be changed R sid ALLOC ERROR nn ON VOLUME vvvvvv REQ SPACE ttt DATA SET dsname ttt tracks have been requested on volume vvvvvv for allocation of the data set dsname An error nn has occurred 04 data
240. session nm to station sid and access method acme has ended and requested session is posted S sid acme X 25 AUTODIAL STOPPED SVCMAX CNTL VALUE EXCEED a S sid acme X 25 AUTODIAL STOPPED ONE SESSION FOR SID EXIST b This message appears only within the RSV protocol for internal use only Dispatcher trace command T DIPS Message a indicates that maximal number of X 25 sessions for all X 25 stations SVCMAX parameter is exceed 91 rvsMVS Messages and Codes 5 rvs Messages Message b indicates that for station sid maximal number of X 25 sessions one session is exceed Next session is not started DF5249P S sid acme LU6 2 AUTODIAL STOPPED LU62MAX CNTL VALUE EXCEED a S sid acme LU6 2 AUTODIAL STOPPED SESNUM STAT VALUE EXCEED b This message appears only within the RSV protocol for internal use only Dispatcher trace command T DIPS Message a indicates that maximal number of LU6 2 sessions for all LU6 2 stations LU62MAX parameter is exceed Message b indicates that for station sid maximal number of LU6 2 sessions SESNUM parameter is exceed Next session is not started DF5254P S sid acme nm REREAD OF RECORD NOT OK PUNKT 1 This message appears only within the rvs protocol for internal use only Dispatcher trace command T DISP It indicates that during selection of send request KD record was change for send session n
241. set already exist on volume To receive the data set on this volume a resident receive entry must be created 08 no space in the VTOC available 12 write read error in the VTOC 20 insufficient space available In case of multiple allocation attempts on other volumes the subtask aborts with RC 12 The user must take care that sufficient space exists on accessible volumes R sid SYMBOLIC UNIT unit NOT DEFINED DATA SET WILL BE STORED ON TAPE An invalid unit name unit has been specified to receive the data set see rvs User Manual The data set will be received on a work volume After receiving it will be copied to tape R sid dsname ALREADY EXISTS ON ALL VOLUMES OF UNIT unit WILL BE STORED ON TAPE The data set dsname should be received on a disk volume which is a part of the unit group unit but all disk volumes of this unit already contain a data set with name dsname The data set will be received on work volume and than it will be copied to tape The following may be done to avoid this situation 1 After processing the received data set delete this data set 2 Specify a unit group which is consisting of more disk volumes R sid dsname INVALID LRECL BLKSIZE IN HEADER The remote station specified an invalid value LRECL or BLKSIZE in the header protocol record for the data set dsname which shall be received R sid I O ERROR ON OUTPUT DATA SET NEW TRANSMISSION NO RESTART A disk error h
242. sid when more than 100 entries have been found In this case only the first 100 entries that are found in the control data set will be displayed INVALID REPLY Incorrect operator entry DATA SET NOT CATALOGED The DF command has been entered and the data set is not cataloged NO INFORMATION POSSIBLE The DF command has been entered but there is no information about the dataset spedified e g if the dataset is migrated 84 rvsMVS Messages and Codes 5 rvs Messages DF5104I INFO dsname volume DF5104I RECS a BLOCKS b LRECL c BLKSI d RECFM e DSORG This message occures if the command DF dsname volume has been entered number of records in the dataset number of blocks in the dataset logical record length blocksize of the dataset record format of the data set data set organization OoDQ0 70 9 The listed values a and b are not in each case the exact values of the record and block number But they give an overview of the size of the data set DF5106I1 DATASET NAME MISSING INVALID This message is issued if the dataset name is missing or if an invalid dataset name e g more than 44 characters in total has been entered 85 rvsMVS Messages and Codes 5 rvs Messages Messages of the Dispatcher Task STARTED DF5201I DISPATCHER SUBTASK VERSION vvv dd mm yy tt mm aa bb cc lENDED J Start or end message of dispatcher routine This program is s
243. solve this problem nn SESSION REJECTED FOR STATION sid ISTATUS INACTIVE A request for establishing a session with station sid has been rejected because the stations entry is not released until now ISTATUS can be changed dynamically by the Operator see rvs Operations Manual if neccessary nn LOGON REQUEST REJECTED BY rvs LOGON EXIT This message is issued by the rvs X 25 CTCP task when the logon exit was scheduled but rvs did not accept the logon request for some reason There might be a temporary problem that is handled by rvs nn COMMAND REJECTED TERMINATION OF rvs X 25 CTCP IN PROGRESS This message is issued by the rvs X 25 CTCP task when an activate command has been entered but termination of the rvs X 25 CTCP task has already started nn STATION ENTRY NOT ASSIGNED NO PAD DEFAULTS SET This message is issued by the rvs X 25 CTCP task when a connection with a PAD stations is to be established rvs tries to reset the PAD parameters to defaults as defined in the rvs stations table In this case the assignment did not exist so the station definitions could not be used nn CALL RECEIVED X 25 DTE NO H HH H 44 This message is issued by the rvs X 25 CTCP task when an X 25 call packet is received The message shows the X 25 DTE number of the caller nn INVALID CALL PACKET RECEIVED LENGTH OF DTE NO EQUAL ZERO This message is issued by the rvs X 25 CTCP task when an invalid X 25 call packet is re
244. ssage displays the remote station socket number datalength and the first 4 bytes of the received data A INCONSISTANT DATA RECEIVED S EXPECTED LENGTH RECEIVED LENGTH This message is issued by the rvs TCP IP task when a received data buffer had a different length than indicated in its header The connection will be terminated A TCLOSE COMPLETE S EP 44 This message is issued by the rvs TCP IP task when a received data buffer had a different length from that indicated in its header The connection will be terminated The socket number and the entry point address are displayed A IP ADDRESS PORT 122 rvsMVS Messages and Codes 5 rvs Messages DF8366E DF8367P DF8368P DF8369P DF8370E DF8371P DF8372P DF8373W DF8374P This message is issued by the rvs TCP IP task when the open process has completed This message displays the own IP address and the own port number READ ERROR DETECTED LENGTH NOT POSITIVE This message is issued by the rvs TCP IP task when a read macro is to be issued The specified length is not positive the session will be terminated as a result of this error which should not occur NO ACTIVE SCT ENTRY FOUND TCB FOR SOCKET CLEARED This message is issued by the rvs TCP IP task when an tcb has been found and no appropriate sct entry exists ACTIVE ODETTE TASK HAS BEEN DETACHED S SID
245. ssage is issued by the Odette File Transfer Protocol Task if SPECIAL LOGIG is used and an error occurred in receiving state The checksum values CO and C1 register 4 old buffer 5 char counter 6 return code and 7 new buffer are shown Z ORT ACCM SESSONID dsn IS NOW BEING RETRIEVED FROM MIGRATION This message is issued by the Odette File Transfer Protocol Task if the dataset to send is migated It shows the start of retrieve Z ORT ACCM SESSONID dsn COULD NOT BE RETRIEVED FROM MIGRATION This message is issued by the Odette File Transfer Protocol Task if the dataset to send is migrated It shows the failing retrieve Z ORT ACCM SESSONID dsn NOT CATALOGED This message is issued by the Odette File Transfer Protocol Task if the dataset to send is not found Z ORT ACCM SESSONID DV COMMAND REJECTED NO ACTIVE TRANSMISSION 158 rvsMVS Messages and Codes 5 rvs Messages DF9442P DF9443P DF9444P DF9445E DF9446E DF9447E DF9448P DF9449P DF9449P This message is issued if a DV command is given but send or receive is not active yet Z ORT ACCM SESSONID EERP RECVD DSN dsn QDATE qdate QTIME qtime This message is issued to inform about receiving a end to end response In case of errors additional messages DF9416 and DF9417I will be given Queuing date and time ist stated S ORT ACCM SESSID FILESIZE UNKNOWN DETERMINATION STARTED This message is issued during start of a transmission Th
246. ssages and Codes 5 rvs Messages DF9919E DF9920E DF9921E DF9923P DF9931P DF9996E R sid mn PASSWORD EXCHANGE REQUESTED BY REMOTE STATION Session rejected Password exchange is neccessary to establish a session with the remote station R sid mn NO PASSWORD EXCHANGE DEFINED The remote station received your password but password exchange is not defined at the remote station Session has been rejected R sid mn PASSWORD NOT ACCEPTED Session rejected Password has not been accepted by the remote station order to validate the access to rvs MVS PFxx command Display default PF key settings PFKEYS member F sid mn PFxx command Display actual PF key settings 184 rvsMVS Messages and Codes 5 rvs Messages This page will be intentionally empty 185 rvsMVS Messages and Codes 6 X 25 Cause and Diagnostic Codes 6 X 25 Cause and Diagnostic Codes This section describes the most important cause and diagnostic codes which may be received within clear or reset indication packets from the X 25 network These codes are important only if the X25 component of rvs is used Most of the codes and their meaning are obtained from the IBM manual IBM 3270 Information Display System X 25 Operation Form GA23 0204 1 Note that clear and or reset indication packets may be sent e by the remote DTE data terminal equipment or e by the remote DCE data circuit terminating equipment or
247. st time into the cache list t4 time of last job submit from this dataset t3 and t4 denote the time interval backward from the current time the format is dd hh mm days hours minutes DF5822I RESET OF JOBDATASET CACHE LIST COMPLETE This message is displayed as a response to command F JDSLIST P It indicates that processing of the reset command has been done DF5901I S sid dsname TRANSMISSION COMPLETE KEPT b DELETED J After transmitting a data set including the T record trailer record the receiving station answers with an R record response record If this R record has been accepted by the transmitting station the disposition the status of the send request entry of the control data set changed from active to complete The disposition specified in the send request entry related to the transmitted data set will be performed The data set is either held on disk uncataloged or deleted DF5902E S sid dsn TRANSMISSION ENDED WITH ERROR The dataset dsn has been sent to station sid After this the termination routine is entered This routine checks the the completeness of the transmission and performs if the transmission was complete the dataset disposition In this case an error has been detected by the termination routine One reason may be that the receiving station has indicated that the transmission was not ok This message indicates that an error has occurred and that the dataset must be retra
248. station sid and access method acme to the dispatcher task within the rvs monitor Postcode of Dispatcher LU 0 00 request for DEQ processing 04 request for DEQ processing and selection of next file 08 same as postcode 04 Postcode of Dispatcher LU6 2 X 25 00 request for DEQ processing 04 end request from ODETTE reply POST 0 next dataset ready to send POST 8 nothing to send 08 selection of next file to send 12 ODETTE task abend request DEQ processing S sid acme LUO RECEIVE SESSION POSTED POST IGNORED This message appears only within the rvs protocol It indicates problems in the communication between different subtasks receive session for station sid and access method acme to the Dispatcher task within the rvs monitor S sid acme POST IGNORED POSTCODE xx This message appears only within the rvs protocol It indicates problems in the communication between different subtasks send session for station sid and access method acme to the Dispatcher task within the rvs monitor S sid acme nm NO SESSION DEFINED FOR THIS STATION This message appears only within the rvs protocol It indicates internal problems within the rvs monitor for send session nm to station sid and access method acme Report this message to the system programmer ACT ENQ SID sid DSN dsname This message is displayed as response to command DD ENQ It displays the currently
249. t which it takes place is also indicated by RESTARTING ON BLOCK nnn The message remains on display until the transmission of data begins S sid ENTER GO OR HOLD OR A NEW RESTART COUNT 61 rvsMVS Messages and Codes 5 rvs Messages DF3402E DF3405E DF3411E DF3412E DF3414A This message is issued if the restart counter automatically determined from the transmission varies considerably from the number of blocks already transmitted This message immediately follows the message Df3400I which indicates the restart The difference can be determined by N sid S name The following possible actions can be taken GO The restart is to take place as indicated in DF3400I HOLD No restart to be executed S sid name is required after the situation is clarified nnnnn 2 6 digit new restart count Since no logical check of this counter is performed by rvs monitor it is advisable to reach an agreement with the receiver by telephone S sid LRECL MUST BE LESS THAN 2045 BYTES SENDING IS IMPOSSIBLE The remote station is not able to handle a line protocol which allows data compression In this case the LERCL of the data set to be transmitted must be less than the physical size of the line buffer 2045 bytes Otherwise no transmission can take place S sid I O ERROR ON VOLUME volume DSN dsname Aread error has occurred in the data set indicated The transmission is aborted No automatic restart takes p
250. tarted just after start of the rvs monitor For a description of the functions performed by this task see Installations Manual chapter 5 rvs Start parameter DSPTI and DSPTIW vvv version of Dispatcher dd mm yy tt mm time of assembly aa bb cc time of last changes in the Dispatcher DF5202I AUTOMATIC DIAL FOR STATION sid INITIATED ON LINE 111 The BSC line Ill is defined as an autodial device This message is issued when autodial to station sid has started on line Ill DF5203I AUTODIAL FOR STATION sid INITIATED acme The message indicates that autodial for station sid and acme has started As a result of autodial for one session to station sid will be activated automatically by rvs DF5204I AUTOACT FOR STATION sid INITIATED LUO The message indicates that autoact for station sid has started Parameter AUTOACT YES is specified for station sid rvs has detected that at least one session to station sid is not active and now tries to activate this session DF5205E S sid acme nm TRANSMISSION OF dsn REJECTED BECAUSE OF EXIT DFUX001 For send session nm to station sid and access method acme the user exit DFUX001 has terminated with a non zero return code there is no authorisation to transmit the dataset dsn to station sid For a description of exit DFUX001 see rvsMVS rvsMVS Installations Manual Appendix A As a result of the rejection the send request will be set into HOLD status immediately DF520
251. tation code and odette station code if a station is connected A IP ADDRESS MISSING OR INVALID ACTIVATION REJECTED This message is issued by the rvs TCP IP task when an activation command is to be executed The IP address of the remote station is not available not defined within stations table or not available by a name server The activation is rejected ACTIVATE REJECTED FOR STATION ISTATUS INACTIVE This message is issued by the rvs TCP IP task when an activation command is rejected due to the initial status INACTIVE of the stations entry Set the status to ACTIVE COMMAND REJECTED TERMINATION OF rvs TCP IP IN PROGRESS This message is issued by the rvs TCP IP task when an activate command has been entered but termination of the rvs TCP IP task has already started 124 rvsMVS Messages and Codes 5 rvs Messages DF83851I UNSOLICITED EVENT OCCURRED TCP IP ADDRESS SPACE HAS TERMINATED This message is issued by the rvs TCP IP task when the unsolicited event exit is driven by the TCP IP address space The TCP IP address space has terminated DF8399P XXXXXXXX The TCPIP Task issues this message The name of TCPIP Task subroutine that gets control is shown For internal use only 125 rvsMVS Messages and Codes 5 rvs Messages Messages of the FTP Receive Control Task STARTED DF8500I D sid sesid FTP SERVER TASK p VERSION lstopPED vvv dd mm yy tt mm aa bb cc Start or stop of
252. tement concerning speed With very small data sets or in the event of a restart the speed determined is severely reduced by intensive computer activations ALLOCATION OPEN CONTROL CLOSE f sid I O SUBTSDK ABEND S sss U uuu A subtask responsible for data input or output terminates abnormally with system completion code sss or user completion code uuu f sid 111 CONNECTION FAILED The line connection was interrupted or failed When determing the cause attention should be payed to previous system messages or messages of the rvs monitor f sid 111 OVERFLOW SWLIST TABLE TO MANY STATIONS DEFINED FOR THIS LINE The rvs stations table contains too many station entries or alias names for stations that use the same limit 200 f sid 111 LINE CANNOT BE STARTED Line Ill cannot be activated the reason may be error in allocation line is incorrectly generated line is OFFLINE A system programmer or IBM technician must be consulted f sid dsname REMOTE ABEND sss uuu An error has occurred at the remonte station sss system completion code uuu user completion code rvs does not attempt an automatic restart for this data set R sid 111 REMOTE BCC xxxx LOCAL BCC yyyy TEXT text rvs stations MVS VSE and DOS check transmitted data by a self computed block check character 2 bytes Each line block of type D contains at the end the BCC computed by the transmitting station The receiving station itself c
253. ters 8 to 15 at the time of the abend DF8840P D sid sesid Driver event The FTP Client Task issues this message when find appropriate FTP Driver event The following list describes the different FTP Driver events POST DISPATCHER DISPATCHER EVENT STOP OR CANCEL EVENT OPERATOR COMMAND EVENT ND FILE EVENT NE FILE EVENT NX FILE EVENT TD FILE EVENT AN FILE EVENT For internal use only DF8850I D sid sesid END OF FTP file type FILE TRANSFER The FTP Client Task issues this message routine when sending of FTP control file is ended The following list describes the different FTP Driver control files 134 rvsMVS Messages and Codes 5 rvs Messages DF8851P DF8852W DF88532 DF8861I DF8862E DF8863E DF8864E DF8865E DF8866E DF8868P DF8870E DF8871E DF88721 DF88731 HEADER DELFILE E E RESP D sid sesid END TO END RESPONSE RECEIVED DSN dsn The FTP Server Task issues this message when an End to End Response EEID protocol unit is received In case of errors additional messages DF8852W and DF8853Z will be given D sid sesid UNKNOWN EEID RECEIVED DSN dsn The FTP Client Task issues this message when an End to End Response EEID protocol unit is received but the EEID can not be associated with a previous file transfer In the message is shown the file name indicated in the EEID protocol unit D sid sesid EEIDDATE gt The FTP
254. th the original name received from the remote station For a description of GDG processing see rvsMVS User s Manual Benutzerhandbuch f sid DATA SET NOT CATALOGED reason 65 rvsMVS Messages and Codes 5 rvs Messages DF3519P DF3520I DF35211 DF3522E DF35231 DF35241 The data set dsn has been received from station sid At end of transmission this data set is to be cataloged but this could not be done because of one of the following reasons DEVICE CODE NOT FOUND the device code of the receive volume could not be determined program internal error RENAME FAILED may happen in conjunction with GDG processing RC xx the CATALOG macro failed xx denotes the returncode register 15 in hexadecimal of the CATALOG macro For this returncode see for example the IBM manual OS VS2 SPL Data Management R sid ADDRESS ALRBPTR xxxx xxxx In case of a dynamic allocation error during allocating a receive data set the dynamic control blocks are listed R sid REMOTE STATION NOT AUTHORIZED TO SPECIFY PROCESSING OPTION A data set shall be received by station sid The transmitter of this data set has been specified some receive parameters i e specification of the receive volume The station sid is not authorized to define specifications like this The data set will be received in a normal way The specifications made by the transmitter are to be ignored see rvsMVS Installation Manual for different author
255. ther mounted volume DF3706A R sid mn SYMBOLIC UNIT unit NOT DEFINED DATA SET WILL BE ON TAPE An invalid unit name unit has been specified to receive the data set on this unit see rvs User Manual The data set will be received on a work volume and then stored to tape RECORD DF3707E R sid mn WRONG b COUNT IN TRAILER BYTE J A ws trailer record has been received This record contains a record and a byte count from the transmitting station A difference between the counts of the own and the transmitting station has been detected A new transmission of this data set is required DF3708A R sid mn dsname ALREADY EXISTS ON ALL VOLUMES OF UNIT unit DF3708A R sid mn OR NOT ENOUGH SPACE ON UNIT unit The data set dsname should be received on a disk volume which is a member of the unit group unit but all disk volumes of this unit group already contain a data set dsname or there is not enough space to allocate the data set on this unit group As a result of this error the 70 rvsMVS Messages and Codes 5 rvs Messages DF3709E DF3710E DF3711E DF3712E DF3713I DF3714P DF3715E DF3716P transmission will be terminated the data set dsname cannot be received until the problem with the unit group unit is solved The following action may be done to avoid this situation Delete the data set after processing automatic jobstart Specify a unit group which consists of more disk volumes
256. tion FILE dsn The FTP Client Task issues this message when a file transfer has been successfully completed In the message is indicated whether the dataset was sent or received direction and the dataset name dsn D sid sesid VOLUME volser IS NOT MOUNTED The FTP Client Task issues this message if the volume containing the file is not mounted 135 rvsMVS Messages and Codes 5 rvs Messages DF8874I D sid sesid FILE filename NOT FOUND ON SPECIFIED VOLUME The FTP Client Task issues this message if the file is not found on the volume specified in the KDRECORD Shown is the virtual file name DF8875I D sid sesid PHYSICAL DSN filename VOLUME volser The FTP Client Task issues this message if the file is not found on the volume specified in the KDRECORD Additional this message shows the physical dataset name of the file DF8877I D sid sesid dsn NOT CATALOGED The FTP Client Task issues this message if the dataset to send is not found DF8881P D sid sesid WORK FILE name EXIST The FTP Client Task issues this message when the FTP control file is found For internal use only DF8884I D sid sesid FILE name WORK FILE ALLOCATIONS ERROR The FTP Client Task issues this message when allocation for FTP control file ended with error For internal use only DF8887P D sid sesid FILE name SEND ERROR reason cod The FTP Client Task issues this message when an error occurs during decode of a received
257. tion Code 913 38 The rvs monitor has no RACF authorization to read this data set The second line of the message appears only if the rename function is to be used In this case dsn2 is the name of the physical data set which is without access rvs authorization After this situation the send request is set in hold status S sid mn dsname nnnnnnn RE VOL volume status The status message is generated at end or abend of transmission nnnnnnn denotes the number of transmitted records of the data set dsname on volume Status may be CANCELLED the transmission has been cancelled by operator ABEND sss uuu the transmission terminated with system sss or user uuu abend code END KEPT the transmission ended without failure S sid mn ESTAE RECOVERY FOR ABEND code DSN dsname A file with the name dsname is to be sent to station sid An abend code has occurred e g system abend S001 or S013 This abend will be recovered by normal termination of the transmission A dump will not be written for the abend The send request is deleted in case of this error it is assigned with the status of an abended transmission S ORT MO KDUPDAT RC XXX R ORT MO 00010203 04050607 O8090A0B OCODOEOF 0123456789ABCDEF Messages DF3634E until DF3635P are for error detection only They are not in effect for users purpose R sid mn DSN dsname STARTED 69 rvsMVS Messages and Codes 5 rvs Messages A rvs
258. transmitted contains an invalid start time I sid dsname SMF RECORD WRITTEN An SMF record has been written after receiving or transmitting a data set The dsname is related to this data set I sid DATA SET FOR TEST NO SMF RECORD WRITTEN No SMF record has been written for this transmission because the rvs start parameter TEST YES has been specified I sid NO SMF RECORD WRITTEN BECAUSE OF MISSING DATA No SMF record was written because no byte of the data set has been transmitted f sid CALL OF ACCOUNTING USER EXIT INITIATED f sid CALL OF ACCOUNTING USER EXIT COMPLETE Indication for the call of the user accounting exit I sid NO SMF RECORD WRITTEN The User SVC designed to write SMF records returned with a non zero return code I sid INVALID START TIME An entry of the control data set relating to a data set which is to be transmitted contains an invalid start time I sid dsname SMF RECORD WRITTEN An SMF record has been written after receiving or transmitting a data set The dsname is related to this data set I sid NO SMF RECORD WRITTEN BECAUSE OF MISSING DATA No SMF record was written because no byte of the data set has been transmitted 35 rvsMVS Messages and Codes 5 rvs Messages DF1601E DF1602E DF1603P DF1604P S sid mn TRANSMISSION OF dsname REJECTED BECAUSE OF EXIT DFUX001 The user exit DFUX001 has been terminated with a non zero return code there is no authoriz
259. ue to availability and the entered display command f the message is related to files queued for transmission R the message is related to files which have been received S the message is related to files which have been transmitted i C entry deleted by operator D sid D entry and data set deleted by operator H for send requests transmission is on hold state Two causes are possible An error has occurred or H sid was entered by the operator In this case the transmission is only started when the S sid dsname command is explicitely entered by the operator For end to end responses EERP EERP is in hold state because an attempt to send the EERP failed A next attempt will be done if the time for the holdreset interval is over I query l record transmitted to remote station but no answer A record received yet After a transmission error S sid dsname must be used for explicit start J a job for further processing has been started jobname is indicated in subsequent line S indicates that the start of the transmission for a file to be sent is initiated used only within the internal transmission protocol of rvs T tape disk or disk tape conversion has been started jobname in subsequent line dsname name of the dataset volume volume where the dataset resides QT ddd hh mm For send requests queuing date and time for the dataset QD yyddd QT hhmmsst For end to end responses queuing date and time of t
260. uires an active stations entry ISTATUS can be changed dynamically operator command F sid see rvsMVS Operations Manual ODETTE ID NOT FOUND An incoming call has been received But the received odette id is not defined whithin the own local stations table INVALID X25 TCP IP ADDRESS An incoming call has been received But the received address X25 number or TCP IP address does not match the address defined for this station whithin the stations table Checking of the remote address will be performed if parameter XNUMCHCK YES TCPIPCHK YES has been specified for this station or if this parameter is valid as a default if specified whithin the CNTL member MAXIMUM SESSION NUMBER EXCEEDED An incoming call has been received But the maximum number of parallel sessions defined for this station is exceeded The connection request is terminated with ESID reason code 08 resource not available DF9A30I Z sid accm sessonid BUFSIZE CREDIT COMPRESS RESTART SPECIAL LOGIC DIRECTION This message is issued by the Odette File Transfer Protocol Task in response to a Display DS command The message shows the exchange buffer size used for the connection the established credit value and whether the compress restart and special logic options are used or not DF9431I Z sid accm sessonid 2272727227 DSN dsn This message is issued by the Odette File Transfer Protocol Task in response to a Display DS command
261. unallocation request for dsn failed xxxx denotes the error reason code yyyy the info reason code of the unallocation see OS VS2 SPL Job Management or MVS XA System Macros and Facilities Volume 1 for more details DF6305I DATASET INCLUDED IN JOBDATASET CACHE LIST USE COMMAND F JDSLIST INSTEAD This message is displayed as a response to command FREE DSN name Unallocation of the dataset name is requested but the command is not executed because the specified dataset 115 rvsMVS Messages and Codes 5 rvs Messages DF6601E DF6901I DF6902E is currently included in the jobdataset cache list of rvs Unallocation of this file may be forced only with the reset command for the cache list F JDSLIST R This command clears the complete cache list including unallocations for all jobdatasets within the cache list k DYNAMIC ALLOCATION ERROR RC xx ERROR yyyy INFO zzzz DDN ddname DSN dsname The monitor and some service programs are attempting to allocate the data sets dynamically using the DDN KD rvsLOG and STATIONS This is possible if they are not allocated by other jobs In case of an error this message appears ALLOCATED A sid LINE nnn b lUNALLOCATED When line control for station sid was activated stopped the line nnn had been allocated unallocated dynamically ALLOCATION A sid 4 ERROR xxxx yyyy FOR LINE nnn lUNALLOCATION During dynamic allocation unallocation of l
262. uring updating the control data set GET PUT OPEN CLOSE 1792 700 This ABEND is coded in the program DF079C00 The program DF079C00 initialization or reorganization the control data set has been executed The error occurred during executing the macros SHOWCB GENCB or PUT RPL 1793 701 This ABEND is coded in the program DF079C00 The program DF079C00 initialization or reorganization the Control Data Set has been executed The first record of the Control Data Set used to initialize the data set does not exist 1800 708 This ABEND is coded in the program DFO80A00 During initialization the parameterrecord could not be obtained from the rvs Control Data Set This parameterrecord contains installation dependent parameter values rvs startparameters used by the program The parameterrecord is created updated during each start of the rvs monitor Occurrence of this error may be solved by starting the rvs monitor at least one time before execution of DFO80A00 1801 709 This ABEND is coded in the program DFO80A00 The data set which is specified in the SYSPRINT DD statement could not be opened 2401 961 This ABEND is coded in the program DF024Bxx Error in the parm entry of the program DF024A00 This program copies a received data set to a tape or a data set which is to be transmitted to a disk The entries of the members RTAPEJC or STAPEJC in the information file rvs TABLES may not have been made in the right columns 2402
263. ut has been lost at remote station e operator at remote station is using incorrect name f sid INVALID REQUEST The previous commond for this station was formally incorerrt or cannot be executed f sid OPEN ERROR ON ddname Line ddname cannot be opened f sid sid2 dsname time HL RESPONSE IGNORED RECORD NOT FOUND The receipt of a high level response end to end control using the dreiecksverkehr function from the next connected station sid2 could not be written to the control data set because there was no fitting control record in the data set dsname is the data set name of the data set which has been transmitted and time is the ready for transmission time of the data set 103 rvsMVS Messages and Codes 5 rvs Messages DF5605E DF56061 DF5608P DF5609P DF5610E DF5611E DF5612E DF5614I1 DF5615P f sid INVALID ID sid RECEIVED CORRECT ID REQUIRED TO CONNECT THE LINE The remote station sent an identification sid which is not defined in the station table of the local station The remote station will be not accepted f sid 111 LINE CONNECTED Station sid itself identified correctly over line Ill Data transmission begins after exchange of some additional information f sid EFFECTIVE SPEED nnnn BPS After transmission of the trailer record the transmission speed is determined for the current data set The larger the data set the more precise is the sta
264. vs cannot load the received PDS because an allocation error for a workfile sysprint file used for loading has occurred for the error code xxxx and the info code yyyy see for example the IBM manual OS VS2 SPL Job Management The transmission will be terminated abnormally See rvsMVS Installations Manual Appendix for a description of PDS transfer mn denotes the session SNA or the line address BSC which was used for receiption of this file DF6107E R sid mn NONZERO RETURNCODE OF PDS LOAD A dataset has been received from station sid The received dataset is an unloaded PDS which must be loaded again rvs cannot load the received PDS Additional error information is available in the rvs printout see message DF6109P The transmission will be terminated abnormally See rvsMVS Installations Manual Appendix for a description of PDS transfer mn denotes the session SNA or the line address BSC which was used for receiption of this file DF6108E R sid mn LOAD OF RECEIVED PDS FAILED Display of this message is always preceeded by one of the messages DF6102E up to DF6107E it is a general error message if load of a PDS failed For more error information see the preceeding message s DF6109P text This message is only printed on the printout SYSWTO file of the rvs monitor not on console It is always preceeded by display of message DF6107E and contains more error information why load of the received PDS was not possible
265. whether the request event was issued or has completed In case of a completed request a returncode may be displayed RC xx U ORT DFO18A COMPUST SET OFF ON U ORT DFO18A COMPVST SET OFF ON U ORT DFO18A COMPTFR SET OFF ON U ORT DFO19A GPF7UST SET OFF ON U ORT DFO19A GPF7VST SET OFF ON U ORT DFO19A GPF7TFR SET OFF ON U ORT DF130B INCLUST SET OFF ON U ORT DF130B INCLVST SET OFF ON U ORT DF130B INCLTFR SET OFF ON Display of internal flags trace for ULS These messages are displayed at start of rvsMVS For internal use only U ORT CHECK SMF SVC MODUL xxxxxxxx U ORT ONAMES RNAMES RC xxx These messages are displayed at start of rvsMVS For internal use only F sid AUTODIAL REJECTED ISTATUS INACTIVE A request to establish a connection with station sid has been rejected because the stations entry is not released until now ISTATUS can be changed dynamically by the Operator see rvs Operations Manual if necessary Bram X sid via sid2 xx b telephone address vram As a reply to the operator command DX relay station sid2 option byte xx of the stations table see 4 4 access method telephone number and address of the station sid are listed ENVIRONMENT MVS RELEASE rel FMID fmid CPU MODEL mod This message displays some information about the MVS environment during start of the rvs monitor D SID COMMAND REJECTED ANOTHER D SID IS STILL PENDING
266. which defines sid as a station connected via BTAM BSC line As a result of this the dial request will be ignored NO BTAM BSC LINE FOUND FOR STATION sid The command DIAL sid has been entered But no line entry has been found within the rvs stations table for the subchannel address es specified within the entry parameter SUBCHANL for station sid As a result of this the dial request will be ignored NO AUTODIAL LINE FOUND FOR STATION sid The command DIAL sid has been entered But none of the line s defined for station sid is defined as an autodial line within the rvs stations table As a result of this the dial request will be ignored PREVIOUS DIAL COMMAND NOT YET PROCESSED The command DIAL sid has been entered But a previous command DIAL sid for the same station sid is not yet processed Only one dial request for a certain station may be specified at one time The additional dial request will be ignored DIAL COMMAND IGNORED 114 rvsMVS Messages and Codes 5 rvs Messages DF62081I DF6209I DF6210I DF6211I DF6301E DF6302I DF6303I DF6304I The command DIAL sid has been entered But this command will be ignored This message is always preceeded by an additional message which indicates the reason for this STATION sid WILL BE CALLED ON LINE 111 The command DIAL sid has been entered This message indicates that this command has been accepted Automatic dialing to station sid
267. which was used for receiption of this file DF6104E R sid mn UNIT NAME OF VOLUME volume NOT FOUND A dataset has been received from station sid The received dataset is an unloaded PDS which must be loaded again rvs cannot load the received PDS onto the specified disk volume volume because rvs cannot find the unit name UCB of this volume Probably rvs internal error The transmission will be terminated abnormally See rvsMVS Installations Manual Appendix for a description of PDS transfer mn denotes the session SNA or the line address BSC which was used for receiption of this file DF6105E R sid mn ALLOCATION ERROR XXXX YYYY FOR DSN dsname A dataset has been received from station sid The received dataset is an unloaded PDS which must be loaded again rvs cannot load the received PDS because an allocation error for the PDS 112 rvsMVS Messages and Codes 5 rvs Messages dsname has occurred for the error code xxxx and the info code yyyy see for example the IBM manual OS VS2 SPL Job Management The transmission will be terminated abnormally See rvsMVS Installations Manual Appendix for a description of PDS transfer mn denotes the session SNA or the line address BSC which was used for receiption of this file DF6106E R sid mn ALLOCATION ERROR XXXX YYYY FOR SYSPRINT FILE A dataset has been received from station sid The received dataset is an unloaded PDS which must be loaded again r
268. will cause an abnormal termination of the OFTP task R sid ACCM SESSID ENQ RETURNCODE rc FOR dsn This message is issued when a file with virtual filename dsn is to be received from station sid and the serialization function failed The transmission will be rejected ENQ returncode 04 indicates that a file with same virtual filename and same queuing date and time is just received from station sid on a parallel session R sid ACCM SESSID INV EERP DATA RECVD ORIG oidl DEST 0id2 R sid ACCM SESSID DSN dsn DATE date TIME time This message is issued when an EERP protocol unit has been received and the verification of the EERP failed The EERP data Odette Ids of originator and destination virtual file name 159 rvsMVS Messages and Codes 5 rvs Messages DF9450I DF9451I DF9452I DF9453I DF9454P DF9455I DF9457E DF9458I DF9463E DF9463E date and time are listed in this message The EERP is accepted but will not be further processed by rvs Z ORT ACCM SESSONID NONZERO RETURNCODE BY name USER EXIT This message is issued by the Odette File Transfer Protocol Task if the USER_EXIT has a nonzero returncode This message is issued when the filename includes characters which don t match with OFTP character subset ISO 646 In the message is shown virtuell filename of the dataset This message is issued when the received filename includes characters which don t match with OFTP character subs
269. wn in the message Also shown in the message is the task name that received the PAD message Note that PAD messages are taken care of by the CTCP nn ERROR IN PAD COMMAND RECEIVED TYPE CODE This message is issued by the rvs X 25 CTCP task when a PAD Error Indication message is received The message shows the error type and error code as reported in the PAD error message nn SEND DATA FLUSHED DUE TO LOCKED SERVER QUEUE This message is issued by the rvs X 25 CTCP task when data to be sent to the Odette File Transfer Protocol task was rejected due to a locked server queue ie the task was not ready to accept the request In the message is indicated the task name nn INVALID COMMAND This message is issued by the rvs X 25 CTCP task when an invalid command has been entered The invalid command is indicated in the message nn OPTION ALL NOT SUPPORTED FOR COMMAND This message is issued by the rvs X 25 CTCP task when the option ALL has been used for a command that does not support the ALL option 165 rvsMVS Messages and Codes 5 rvs Messages DF9526E DF9527W DF9528W DF95291 DF9530I DF9531I DF9532I DF9533I DF9534I nn INVALID COMMAND PARAMETER This message is issued by the rvs X 25 CTCP task when an invalid parameter to a used command is detected nn SPECIFIED VCB NOT FOUND This message is issued by the rvs X 25 CTCP task when the Virtual Circuit Block number VCB speci
270. xt The error message text has been received from the remote station f sid mn EERP SENT RECVD DSN dsname QD date QT time An end to end response has been sent to received from station sid The message displays the related datasetname dsn and the queuing date and time of the related file End to end responses are used for transmissions which run at least via one or more relais stations The message displays the flow of an EERP and is used for problem determination only f sid mn r RECORD RECEIVED TEXT text A rvs control record which has been received from the remote station is displayed on print output f sid mn r RECORD HAS BEEN SENT TEXT text The transmission of a rvs control record type r is displayed on print output f sid mn command This message is to be displayed in response to an entered command f sid mn sid2 dsname TIME OUT The transmisson of the data set identified by dsname will be terminated because of missing responses from the remote station f sid mn NO BUFFER AVAILABLE TO SEND HEADER OR TRAILER All line buffer are temporarily in use The transmission is cancelled The status of the send request is changed to the HOLD status f sid mn SEND r RECORD FAILED SENSE ssss uuuu see DF9105E S sid mn text 148 rvsMVS Messages and Codes 5 rvs Messages DF9207I DF9208E DF9209E DF9210E DF9211E DF92251I DF9226P DF9230P DF9235P see DF910

- ServiceNet - T

Contents

Download Pdf Manuals

Related Search

Related Contents