PD – 201 Low Profile Customer Display User`s Manual
Contents
1.2. remove the UPS battery cover Step C Take off UPS battery cover and remove the customer display cover by pushing at the 2 latches down Step D Pass PD 201 interface cable to go through the square opening in the UPS battery cover and insert the 2 lugs at front bottom of PD 201 into the correspondent positions of UPS battery cover then press down the 2 latches on rear bottom of PD 201 down till they firmly click in Step E Before installing the PD 201 UPS battery cover assembly back into the DT system top cover check the bottom side of the PD 201 UPS battery cover assembly to route the interface cable in between the guide posts on the UPS battery cover Step F Raise the UPS battery in the UPS battery cavity for a while if it is installed for passing the PD 201 interface cable through the passage in the UPS battery cavity to enter the connection area Pull the cables gently while installing the PD 201 UPS battery cover assembly back onto the system top cover with the 3 lugs going in first to minimize the excessive cable length inside the battery cavity Connect the PD 201 cable to the COM port settled Settle all excessive cable length in connection area with some cable ties then close back the cable cover POWER ON SIGN With interface cable connection well installed and with COM port power in DT system set turn on the Posiflex POS system a firmware identifier as power on sign will appear on the pole display screen for a while to ind
3. a PD 201 Low Profile POSIFL Customer Display User s Manual FCC Notes ee This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested an found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference Warranty Limits Warranty terminates automatically when any person other than the authorized technicians opens the machine The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application About This Manual Posiflex has made every effort for the accuracy of the content in this manual However Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein nor for direct indirect incidental consequential or otherwise damages including without limitation loss of data or profits resulting fro
4. and execute the file SETUP EXE to install the OPOS Control Manager To add the customer display under OPOS control please set in OPOS Control Manager device name PD20x Line Display in the top row Please then select the COM port in the 3 row and set baud rate to 9600 in 4 row Part 4 SPECIFICATIONS OPTICAL Number of digits 16 digits row 1 row Dot matrix 5 X 7 dots Digit height 8 07 mm Digit width 4 85 mm Display type STN positive transflective LCD Display color Yellow Green MECHANICAL Height 51 7 mm Width 138 9 mm Depth 44 2 mm Display Window Height 11 4mm Display Window Width 96 8 mm Display Inclination Angle 45 Case color Same as DT system ELECTRICAL Power from interface port of DT system 5VDC 1A ENVIRONMENTAL Operating temperature 0 to 40 C Storage temperature 10 to 60 C Operating humidity 20 to 85 non condensing Storage humidity 5 to 90 non condensing WARNING If the user opens the customer display housing to make any modification all the product warranty will be voided NOTE Please refer to Posiflex Product Information CD or DVD or visit our web http www posiflex com tw for further information when needed Part 5 COMMAND LIST EPSON COMMAND MODE POWER ON DEFAULT MODE NAME BS HT HOM CLR Move cursor to specified position n 1 16D US B US C USE Blink display screen n 0 255 PST COMMAND MODE lt 14 gt lt 16 gt Switch to Epson Mode
5. eir respective holders P N 19400901010 Part 1 a BRIEF INTRODUCTION THE PRODUCT The PD 201 is a low profile customer display option designed for Posiflex DT 20X POS terminals It is delivered in separate carton for the host system and shall be installed per instructions in the DT system user s manual FEATURES LCD Liquid crystal display with yellow green back light One line display with 16 characters Easy viewing characters 4 85 mm by 9 66 mm Long life and trouble free operation Selectable command emulation modes including PST and EPSON command emulation modes e Simple installation e Supports Serial RS232 interface e Support European Japanese Russian in separate models Part 2 INSTALLATION GUIDES HOST SYSTEM PREPARAION For serial interface RS232 PD 201 to be used in DT 20X series you have to adjust during power off the internal jumper of the host system to supply 5 V DC to the COM port selected for the serial interface customer display This adjustment has to be done by a qualified electronic technician following guide from relevant technical manual INSTALLATION For PD 201 installation please refer to the detailed instructions given in the user s manual delivered with the DT POS system and follow the steps A to F below sequentially Step A Open the jumper setting service window and set DC 5V support to the COM port Step B Open the cable cover and push at the 2 latches toward the system to
6. icate that pole display is self tested O K and ready to work Part 3 E USING THE CUSTOMER DISPLAY COM PORT SELECTION This series of customer display is designed to serve in Posiflex POS systems with RS232 interface It is advisable to well study the I O port availability of the host system before determining which COM port to be used When a RS232 serial interface model of PD 201 is used the jumper on main board of the host system must be modified to supply power to the COM port designated for PD 201 Whenever the RS232 interface PD 201 is to be removed from the host system consequently the jumper has to be changed back to neutralize the power support in the COM port otherwise damage could occur COMMAND MODE SELECTION The PD 201 will always be in the Epson command mode at power on It can enter or exit the PST command mode through software command DRIVER INSTALLATION FOR RS 232 INTERFACE APPLICATION For direct I O control over the serial interface RS232 you have to send all commands listed later in this manual under communication protocol 9600 bps none parity 8 data bits 1 stop bit with hardware handshaking on CTS signal to the COM port used No other driver installation is required FOR OPOS APPLICATION Find the subfolder Drivers UPOS OPOS of the Posiflex Product Information CD or DVD or download it from our web site http www posiflex com tw Download 20list asp Status 1 amp Series_Name U POS amp Model_Name OPOS
7. m the furnishing performance or use of this material This information is provided as is and Posiflex Technologies Inc expressly disclaims any warranties expressed implied or statutory including without limitation implied warranties of merchantability or fitness for particular purpose good title and against infringement The information in this manual contains only essential hardware concerns for general user and is subject to change without notice Posiflex reserves the right to alter product designs layouts or drivers without notification The system integrator shall provide applicative notices and arrangement for special options utilizing this product The user may find the most up to date information of the hardware from web sites http www posiflex com or http www posiflex com tw All data should be backed up prior to the installation of any drive unit or storage peripheral Posiflex will not be responsible for any loss of data resulting from the use disuse or misuse of this or any other Posiflex product All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without prior express written consent from Posiflex Technologies Inc the publisher of this documentation Copyright Posiflex Technologies Inc 2008 All brand and product names and trademarks are the property of th
Download Pdf Manuals
Related Search