DIESEL WATER/TRASH/ CHEMICAL PUMPS
Contents
1. e 2006 42 EC Machinery directive 2004 108 EC EMC directive e 2000 14 EC Noise emissions directive e 97 68 EC NRMM Emissions directive EC DECLARATION OF CONFORMITY The undersigned as authorised by Genpower Ltd Declares that the following equipment manufactured under licence by Hyundai Korea Conforms to the Directive 2000 14 EC as amended of the European Parliament and of the council on the approximation of the laws of the Member States relating to the noise emission in the environment by equipment for use outdoors Equipment Category Product Name Model Type Serial No Net installed power The technical documentation is kept by Water Pump Hyundai DHYSOE DHYCS5OLE Diesel Water Pump Electric Start Diesel Chemical Water Pump Electric Start 3 kW Kevin Stanley Genpower Ltd Isaac Way Pembroke Dock Pembrokeshire 5472 4RW The conformity assessment procedure followed was in accordance with annex V of the Directive Tested at sound Test Report Measured Sound Power Level Guaranteed Sound Power Level Genpower Ltd Isaac Way Pembroke Dock Pembrokeshire 5A72 4RW Test sheet Water Pump Diesel DHYS5OE Electric Start 105 dB A 105dB A A copy of this certificate has been submitted to the European Commission and to EU Member State United Kingdom Place of Declaration Date Signed by Position in Company Pembroke Dock SA72 4RW 27 February 2015 Ead2. TROUBLESHOOTING 9 1 If you are experiencing a problem that is not listed in this chart or have checked all the possible cause listed and you are still experiencing the problem see your authorized dealer Engine lacks power 1 Dirty air filter 1 Replace air filter 1 STOP RUN lever in STOP position 1 Move lever to RUN position 2 No 2 No fuel in engine in 2 No fuel in engine 2 Fill fuel tank or turn on fuel supply 3 Battery discharged 3 Charge or replace battery 4 Faulty starter solenoid motor 4 Check replace as required Engine will not start Engine runs well at no load but bogs down under full 1 Engine speed is too slow 1 Adjust STOP RUN lever to suit load load 5 STOP RUN lever incorrectly set 5 Move STOP RUN lever 1 Out of diesel 1 Fill fuel tank Engine shuts down durin r r 7 l E 2 Fill crankcase with oil to proper operation 2 Low oil level od Engine lacks power 1 Dirty air filter 1 Replace air filter 1 Move STOP RUN lever until engine runs smoothly Engine putts or falters 1 STOP RUN lever incorrectly set All engine servicing to be taken to Manufacturer s authorised service outlet PAGE 18 10 WINTER STORAGE 10 1 To protect the unit 10 1 1 To protect unit from damage caused by freezing temperatures make sure unit is fully drained of water Failure to drain water from the pump fully may cause damage due to freezing this damage will
3. Name and address of manufacturer or Authorised representative Genpower Ltd Isaac Way Pembroke Dock Pembrokeshire 472 4RW PAGE 22 NOTES PAGE 23 GENPOWER LTD Isaac Way London Road HY Li B DAI Pembroke Dock UNITED KINGDOM SA72 ARW T 44 0 1646 687 880 F 44 0 1646 686 198 E info hyundaipowerequipment co uk www hyundaipowerequipment co uk
4. of your pressure washers life dispose of it in an environmentally friendly manner 11 3 Thoroughly empty the oil lubricant and fuel tanks and dispose of the remainders at a special collecting point or re cycling facility 11 4 At machine end of life please also dispose of at your local collecting recycling point 12 SPECIFICATIONS 13 1 1 See engine manual supplied with machine Or you can obtain a copy of your manual at Model DHYSOE DHYCSOLE DHY80E DHYTS8OE Hyundai D200 4 stroke single cylinder Hyundai D300 4 stroke single cylinder ruetan 3 6 3 6 6 7 6 7 capacity L Net installed power 3600rpm hp kw Aluminium housing Aluminium housing with with 3 8 2 8 3 8 2 8 5 5 4 00 5 5 4 00 Aluminium housing with a cast iron impeller a cast iron impeller a cast iron impeller Total head m SS ee E a 8 O 7 e 60 000 60 000 Max flow I h 36 000 Weight Kg 8 J 8 amp 9 9 Assembled dimension LX W XH mm 570x470x 670 540 x 450 x 540 590 x 490 x 590 13 GENPOWER CONTACT DETAILS 590 x 490 x 590 13 1 Postal address Genpower Limited Isaac Way Pembroke Dock Pembrokeshire SA72 4RW UK 13 2 Telephone contact number Office 44 0 1646 687880 13 3 Email contacts Technical service genpower co uk 13 4 Web site www hyundaipowerequipment co uk PAGE 20 15 DECLARATIONS of CONFORMITY 15 1 Genpower Ltd confirms that this water pump conforms to the following EC directives
5. to mistake this very dangerous poisoning for something else 1 3 3 To avoid Carbon monoxide poisoning DO NOT Use Petrol Diesel powered equipment inside a home garage tent camper van mobile home caravan or boat The list is not exhaustive if you are in any doubt contact your dealer 1 3 4 If you think you or someone around you has been affected by carbon monoxide poisoning 1 3 4 1 Get fresh air immediately by opening doors and windows turning off machine and leaving the affected area 1 3 4 2 See your doctor immediately or go to hospital let them know that you suspect carbon monoxide poisoning 1 3 5 DO NOT use in an enclosed area or a moving vehicle A DANGER BREATHING IN CARBON MONOXIDE FUMES CAN KILL YOU To help protect against CO poisoning install a Carbon Monoxide detector Da NEVER use Petrol Diesel powered equipment inside especially a home garage tent camper van caravan motorhome or boat EVEN if doors windows vents and hatches are open Only use OUTDOORS and as far away from doors windows vents and open hatches as possible to prevent inhaling fumes READING MANUAL BEFORE USE WILL HELP AVOID OTHER MACHINE HAZARDS 1 4 General fuel safety Oo TOXIC FUMES 1 4 1 Fuel Safety additional information can be obtained from the Health and Safety Executive HSE document SR16 1 4 2 A CAUTION All fuels are Flammable 1 4 3 Keep away from all ignition sources i e Heaters lamps sparks f
6. HYUNDAI DIESEL WATER TRASH CHEMICAL PUMPS Models DHY50E DHYCSOLE DHYSOE DHYTSOE User Guide Licensed by Hyundai Corporation Korea RECORD OF IDENTIFICATION NUMBERS If you need to contact an Authorised Dealer or aftersales on 01646 687 880 for information on servicing always provide the product model and identification numbers You will need to locate the model and serial number for the machine and record the information in the places provided below eem Model Number Numbers m me Jemen 0000 0 D This unit is shipped without oil and fuel You Must make sure that the unit is filled with oil and fuel before attempting to start See section 4 PAGE 2 10 11 12 13 14 CONTENTS Section Description OPERATION NOTES amp RECORD of IDENTIFICATION NUMBERS SAFETY SAFE OPERATION MACHINE PARTS OIL amp FUEL ASSEMBLY OPERATION STARTING STOPPING MAINTENANCE TROUBLESHOOTING WINTER STORAGE ENVIRONMENTAL DISPOSAL SPECIFICATIONS CONTACT DETAILS DECLARATIONS of CONFORMITY PAGE 3 Page N N S 11 12 13 13 15 15 16 17 18 19 20 20 20 21 22 s X n 1 1 The operator of the machine 1 1 1 Is responsible for and has a duty of care in making sure that the machine is operated safely and in accordance with the instructions in this user manual 1 1 2 Should never leave it in a condition which would allow an untrained or unauthorised person s to operate this machin
7. Tighten hose clamp securely 5 3 Insert connect discharge hose Optional 5 3 1 If desired use a commercially available hose DO NOT use a hose with an inside diameter smaller than the pump s discharge port size 5 3 2 Slide barb cuff over hose barb Insert rubber seal into end of barb cuff as shown earlier 5 3 3 Screw hose barb assembly onto pump in clockwise rotation until hose barb assembly is tightened securely PAGE 12 5 3 4 Slide hose clamp over end of discharge hose Slide discharge hose onto hose barb Tighten hose clamp securely 5 3 5 You may choose to assemble the discharge and suction hose as shown above or by using cam lock connections Cam locks are another commonly used water pump connection OPERATION 6 1 What is head 6 1 1 Headrefers to the height of a column of water that can be delivered by the discharge of the pump 6 1 2 Suction Head is the vertical distance between the centre of the pump and the surface of the liquid on the suction side of the pump May also be referred to as suction lift The atmospheric pressure of 14 7 psi at sea level limits suction head lift to less than approximately 26 feet for any pump 6 1 3 Discharge Head is the vertical distance between the pump s discharge port and the point of discharge which is the liquid surface if the hose is submerged or pumping into the bottom of a tank 6 1 4 Total Head is the sum of the suction head value plus the discharge head valu
8. Y Product Manager Mame and address of manufacturer or Authorised representative Genpower Ltd Isaac Way Pembroke Dock Pembrokeshire 5A72 JRW PAGE 21 EC DECLARATION OF CONFORMITY The undersigned as authorised by Genpower Ltd Declares that the following equipment manufactured under licence by Hyundai Korea of the European Parliament and of the council on the approximation of the laws of the Member States relating to the noise emission in the environment by equipment for use outdoors Equipment Category Product Name Model Type 5erial No Net installed power The technical documentation is kept by Water Pump Hyundai DHYSOE Hyundai DHYTSOE Diesel Water Pump Electric Start Diesel Trash Water Pump Electric Start 4 5 kW Kevin Stanley Genpower Ltd Isaac Way Pembroke Dock Pembrokeshire S472 4RW The conformity assessment procedure followed was in accordance with annex V of the Directive Tested at sound Test Report Measured Sound Power Level Guaranteed Sound Power Level Genpower Ltd Isaac Way Pembroke Dock Pembrokeshire 5A72 4RW Hyundai Water Pump Diesel DHYS80E_DYHT80E Electric Start NTFC 109 dB A 109 dB A A copy of this certificate has been submitted to the European Commission and to EU Member State United Kingdom Place of Declaration Date Signed by Position in Company Pembroke Dock 5472 4RW 27 February 2015 I ah ly Product Manager
9. ber is filled with water before starting the engine NEVER run pump without priming 6 3 2 Remove priming plug from top of pump 6 3 3 Fill pump with clean clear water up to top of discharge outlet 6 3 4 Replace priming plug 6 4 Locating strainer basket into water source PAGE 14 The Improper treatment of water pump can damage it and shorten its life NEVER operate pump without strainer connected to end of suction hose Keep strainer out of sand or silt place in bucket or on stones DO NOT let pump run dry or damage to seals may result 6 4 1 Place strainer basket into water to be pumped basket must be fully immersed in water 7 STARTING STOPPING Starter cord kickback rapid retraction can result in bodily injury Kickback A WARNING will pull hand and arm toward engine faster than you can let go When starting engine pull cord slowly until resistance is felt and then pull rapidly to avoid kickback Broken bones fractures bruises or sprains could be a result of incorrect use 7 1 Electric start 5 7 1 1 1 Make sure the water pump is on a stable flat level surface 7 1 1 2 Make sure the water pump has been filled with ja DHYT80E both oil and diesel and to the correct levels Y dm 7 1 1 3 Turn the fuel tap 1 down to the ON position 7 1 1 4 Unscrew the STOP RUN lever 3 then move it to the RUN position lock it into position by tightening the screw 7 1 1 5 Turn the key switch 4
10. e 6 1 5 As water pumping height increases pump output decreases The length type and size of the suction and discharge hoses can also significantly affect pump output 6 1 6 It is important for the suction operation to be the shorter part of the total pumping action This will decrease the priming time and improve pump performance by increasing the discharge head 6 1 7 Suction head is a maximum of 25 feet and discharge head should be a maximum of 81 feet Total head cannot be more than 106 feet as shown on next page PAGE 13 Discharge 6 2 Pump positioning 6 2 1 For best pump performance locate the pump on a flat level surface as close as possible but avoiding soft edges to the water to be pumped 6 2 2 Secure water pump to prevent it tipping over Use hoses that are no longer than necessary 6 2 3 IMPORTANT Direct open end of discharge hose away from property electrical supply sources and other equipment that you do not want to get wet Fuel and its vapours are extremely flammable and explosive A WARNING Fire or explosion can cause severe burns or death E EXPLOSION 6 2 4 This water pump is not for use in mobile equipment or marine applications 6 2 5 DO NOT tip engine or equipment at angle which causes fuel to spill 6 2 6 Secure water pump Loads from hoses may cause tip over 6 3 Priming the pump N NOTE The Improper treatment of water pump can damage it and shorten its life 6 3 1 Be sure cham
11. e 1 1 2 1 Should take care and show due diligence for the safety of and with regard to those around whilst using the machine to include but not limited to 1 1 2 1 1 Elderly children pets livestock and property 1 2 Some or all of the following PPE Warning Signs and symbols may appear throughout this manual and you must adhere to their warning s Failure to do so may result in personal injury Personal Protective clothing PPE N DANGER ZA WARNING CAUTION DANGER indicates a WARNING indicates a CAUTION indicates a NOTE indicates a hazard which if not hazard which if not hazard which if not situation that could avoided could result in avoided could result in avoided might result easily result in serious injury or death serious injury or death in minor or moderate equipment damage READ MANUAL injury E EXPLOSION ELECTRIC SHOCK KICKBACK HOT SURFACE TOXIC FUMES SLIPPERY MOVING PARTS PAGE 4 1 3 Carbon monoxide O TOXIC FUMES 1 3 1 Carbon monoxide is a colourless and odourless gas Inhaling this gas can cause death as well as serious long term health problems such as brain damage 1 3 2 The symptoms of Carbon monoxide poisoning can include but not limited to the following 1 3 2 1 Headaches Dizziness Nausea Breathlessness Collapsing or Loss of consciousness 1 3 2 2 Carbon monoxide symptoms are similar to flu food poisoning viral infections and simply tiredness It is quite common for people
12. in an clockwise direction against spring tension once engine has started release r the key 7 1 1 6 The water pump speed can be adjusted by moving the 2 STOP RUN lever 3 to suit the load 7 2 Recoil start 7 2 1 1 Make sure the water pump is on a stable flat level surface 7 2 1 2 Make sure the water pump has been filled with both oil and diesel and to the correct levels 7 2 1 3 Turn the fuel valve 1 down to the ON position 7 2 1 4 Unscrew the STOP RUN lever 3 then move it to the RUN position lock it into position by tightening the screw 7 2 1 5 Slowly pull the recoil handle 2 until resistance is met then move the de compression lever 5 to the down position 7 2 1 6 Grasp recoil handle 2 and pull back quickly DO NOT let go of handle instead let it return slowly 7 2 1 7 If engine fails to start first time repeat from 7 2 1 3 7 2 1 8 If engine still does not start hold the de compression lever 5 in down position and pull recoil handle two three times Then repeat from 7 2 1 3 7 1 1 6 The water pump speed can be adjusted by moving the STOP RUN lever 3 to suit the load PAGE 15 7 2 1 9 Important It may take a few minutes for water pump to begin pumping water Contact with muffler exhaust area can result in serious burns HOT SURFACE A WARNING Exhaust heat gases can ignite combustibles structures or damage fuel A FIRE tank causing a fire 7 2 1 10 DO NOT touch hot
13. ing with oil and fuel check that the pump is on stable and level ground 4 1 Oil 4 1 1 Undo oil filler plug 1 fill with E clean 15W 40 Oil 4 1 2 Fill to the top of the threads 4 1 3 Do not overfill 4 1 4 Clean up any spilt oil before starting machine 4 1 5 Do not allow any dust or dirt to enter the oil system Oil Dipstick Upper Level 4 2 Fuel 4 2 1 Undo filler cap 1 4 2 2 Fill with fresh Diesel mii vA LO 4 2 3 Fill to bottom of the filler neck 2 pee 4 2 4 Do not overfill DIESEL WATER PUMP 2 4 2 5 Clean up any spilt fuel before starting machine 4 2 6 Do not allow any dust or dirt to enter the fuel B system PAGE 11 5 ASSEMBLY A NOTE Hose connections are supplied Hoses ARE NOT supplied as standard with pump Your water pump requires some assembly and is ready for use after it has been properly filled with the recommended oil and fuel If you have any problems with the assembly of your water pump please call the water pump help line at 01646 687 880 If calling for assistance please have the model and serial number available 5 1 Connecting the suction hose to the pump 5 1 1 Slide hose clamp A over end of hose B Slide suction hose onto hose barb C Tighten hose clamp securely to the hose 5 2 Attaching the suction hose to the strainer basket 5 2 1 Slide hose clamp over the hose Attach open end of the suction hose to strainer hose barb
14. not be covered under warranty 10 2 Long term storage 10 2 1 If you do not plan to use the water pump for more than 30 days you must prepare the engine and pump for long term storage 10 3 Fuel system 10 3 1 Fuel will become stale when stored over 30 days Stale fuel causes acids and gum deposits to form in the fuel system or on essential carburetor parts 10 3 2 Prior to storage the diesel must be drained from the engine into an approved container 10 3 3 Then run engine until it stops from lack of fuel 10 4 Storing the engine 10 4 1 See the engine operator s manual for instructions on how to properly prepare the engine for storage 10 5 Additional storage tips 10 5 1 DO NOT store fuel from one season 10 5 2 Replace fuel container if it starts to rust Rust and or dirt in fuel can cause problems if it s used with this unit 10 5 3 Once unit has cooled down cover unit with a suitable protective cover that does not retain moisture 10 5 4 Store unit in a clean and dry area Storage covers can be flammable O A WARNING DO NOT place a storage cover over a hot water pump Let equipment cool for a sufficient time before placing the cover on the equipment PAGE 19 11 EVIROMENTAL DISPOSAL 11 1 Never pour remainders of oils fuel mixtures into any drain sewerage system or soil Dispose of it in a proper environmentally friendly way e g at a special collecting point or re cycling facility 11 2 At the end
15. parts and AVOID hot exhaust gases 7 2 1 11 Allow equipment to cool before touching 7 2 1 12 Keep at least 6 feet 2 0 m of clearance on all sides of water pump including overhead 7 3 Stopping the water pump 7 3 1 Move the STOP RUN lever 3 to the STOP position 7 3 2 Turn the key switch 4 anti clockwise to the OFF position 7 3 3 Turn fuel valve to OFF position 7 4 Draining and flushing the water pump 7 4 1 Disconnect and drain the suction and discharge hoses 7 4 2 Remove the drain plug at bottom of the pump 7 4 3 To protect the unit from damage caused by freezing temperatures make sure unit is fully drained of water 7 4 4 Remove the primer plug from top of the pump and flush the internal components of the pump with clean water ct 7 4 5 Replace both plugs and finger tighten PAGE 16 8 MAINTENANCE Service and maintenance must be performed by an authorised agent DO NOT tamper with or attempt to adjust the pressure switch or safety valve A WARNING Before moving or carrying out any maintenance on the compressor ensure the ignition switch is OFF and that the tank pressure has been vented Allow the compressor to cool down for a period of time 8 1 In order to keep the engine in good working condition periodic maintenance is essential 8 2 Engine 8 2 1 Forall engine maintenance please refer to the engine manufacturers handbook supplied for the full schedule PAGE 17 9
16. perate water pump from a stable surface 2 5 The area should have adequate drainage to reduce the possibility of a fall due to slippery surfaces Fuel and its vapours are extremely flammable and explosive N WARNING Fire or explosion can cause severe burns or death EXPLOSION 2 6 When adding or draining fuel 2 6 1 DO NOT overfill tank Allow space for fuel expansion 2 6 2 Turn water pump OFF and let it cool at least 2 minutes before removing fuel cap Loosen cap slowly to relieve pressure in tank 2 6 3 Fill or drain fuel tank outdoors 2 6 4 If fuel is split clean it up and or allow it to evaporate before starting engine 2 6 5 Keep fuel away from sparks open flames pilot lights heat and other ignition sources 2 6 6 DO NOT use near any naked flames other sources of ignition and lighting cigarettes 2 7 When starting equipment 2 7 1 Make sure that muffler exhaust fuel cap and air cleaner are in place 2 9 When operating equipment 2 9 1 DO NOT tip engine or equipment at angle which can cause fuel to spill 2 9 2 DO NOT Use pump for fuels sea water beverages acids chemical solutions Except for the DHYCSOLE or any other liquid that promotes corrosion PAGE 7 2 10 When transporting or repairing equipment 2 10 1 Transport repair with fuel tank EMPTY or with fuel shutoff valve OFF 2 10 2 Disconnect spark plug wire 2 11 When storing fuel or equipment with fuel in the tank 2 11 1 Store away from fu
17. rate pump without strainer basket connected to end of suction hose 2 30 NEVER allow vehicles to drive over hoses If a hose must be positioned across a roadway use planking on each side of hose to allow vehicles to pass over without obstructing or collapsing hose PAGE 9 2 31 Anchor pump to avoid equipment movement 2 32 Keep equipment away from edge of river or lake where it could cause the bank to collapse 2 33 DO NOT insert any objects through cooling slots 2 34 NEVER operate units with broken or missing parts or without protective housing or covers 2 35 DO NOT by pass any safety device on this machine 2 36 NEVER move machine by pulling on hoses Use frame on unit 2 37 Check fuel system for leaks or signs of deterioration such as chafed or spongy hose loose or missing clamps or damaged tank or cap 2 38 Correct all defects before operating water pump PAGE 10 3 MACHINE PARTS Generic image showing parts locations will vary on each model For engine locations please supplied engine manual 1 Oil Drain 5 Battery 9 Recoil Starter 13 Stop Run 2 Oil Filler 6 Starter Motor 10 Pump Priming Cap 14 Pump Outlet 3 Pump Drain Plug 7 Pump Housing di Bhws 0 A Pumpinet 8 on off Key Switch 12 FuelTank 4 OIL amp FUEL Do Not fill with oil and fuel whilst engine is hot or running Before checking and or fill
18. rnaces stoves water heaters clothes dryers or other appliances that have pilot light or other ignition source 2 12 Electric shock risk A WARNING Risk of electrocution 2 Contact with power source can cause electric shock or burn ELECTRIC SHOCK 2 12 1 NEVER allow pumped water and spray to come into or near power sources 2 13 Starter cord kickback Rapid retraction Starter cord kickback rapid retraction can result in bodily injury gt Kickback will pull hand and arm toward engine faster than you can let A WARNING go eaae Broken bones fractures bruises or sprains could result Keep hands and body clear from discharge of pump 2 13 1 When starting engine pull cord slowly until resistance is felt and then pull rapidly to avoid kickback 2 13 2 Secure discharge hose to avoid whipping Contact with muffler exhaust area can result in serious burns Exhaust HOT SURFACE A WARNING heat gases can ignite combustible materials and or structures which O can cause fires 2 14 3 DO NOT touch hot parts and AVOID hot exhaust gases 2 14 4 Allow equipment to cool before touching 2 14 5 Keep at least 6 feet 2 0 m of clearance on all sides of water pump including overhead PAGE 8 2 16 Starting and rotating parts A WARNING Starter and other rotating parts can entangle hands hair clothing or accessories MOVING PARTS 2 16 1 NEVER operate the water pump without protective guards hou
19. rom grinding or welding 1 4 4 Hot work on tanks that have contained fuel is extremely dangerous and should not be carried out 1 4 5 Keep work area clean and tidy 1 4 6 Clean up all spills promptly using correct methods i e absorbent granules and a lidded bin 1 4 7 Dispose of waste fuels correctly PAGE 5 TOXIC FUMES 1 5 Diesel safety 1 5 1 Always fuel and defuel in well ventilated area 1 5 2 Always wear correct suitable and fit for purpose Personal Protective Equipment PPE suggested items are as follows but are not limited too 1 5 3 Hand protection 1 5 4 Protective clothing 1 5 5 Respiratory protective equipment should be used when in an unventilated area 1 5 6 When defueling always use a propriety fuel retriever 1 5 7 Always carry fuel in the correct and clearly marked container PAGE 6 2 SAFE OPERATION A running engine gives off carbon monoxide which is an eo A WARNING odourless colourless poisonous gas E Inhaling carbon monoxide can cause headache fatigue dizziness vomiting confusion seizures nausea fainting or death 2 1 Operate water pump ONLY outdoors 2 2 Keep exhaust gas from entering a confined area through windows doors ventilation intakes or other openings 2 3 DO NOT start or run engine indoors or in an enclosed area even if windows and doors are open A WARNING Use of water pump can create puddles and slippery surfaces SLIPPERY 2 4 O
20. sing or covers 2 16 2 DO NOT wear loose clothing jewellery or anything that may be caught in the starter or other rotating parts 2 16 3 Tie up long hair and remove jewellery 2 17 Eye protection JAN WARNING Risk of eye injury Spray can splash back or propel objects FLYING OBJECTS 2 17 1 Always wear safety goggles when using this equipment or in vicinity of where equipment is in use 2 17 2 Before starting the water pump be sure you are wearing adequate safety goggles 2 17 3 NEVER substitute safety glasses for safety goggles Excessively high operating speeds increase risk of injury and damage to water A CAUTION puri Excessively low speeds impose a heavy load 2 18 DO NOT tamper with the governed speed 2 19 DO NOT modify the water pump 2 20 DO NOT allow unqualified untrained persons or children to operate or service water pump 2 21 If you have questions about intended use ask dealer or contact nearest authorised dealer 2 22 Be sure pump chamber is filled with water before starting the engine 2 23 Never run pump without priming 2 24 Use a non collapsible hose on the suction side of the hose 2 25 Use water pump only for intended uses 2 26 Pumping sea water beverages acids chemical solutions or any other liquid that promotes corrosion can damage the pump 2 27 Ensure all connections are air tight 2 28 DO NOT obstruct the suction or discharge hose in any way 2 29 NEVER ope
Download Pdf Manuals
Related Search