Manual (english)
Contents
1. Each aux mix has a master level control that adjusts the output level to match external equipment or trims the monitor effect or other send without affecting the mix balance Up to 10dB boost is available above the normal OdB position Note that this becomes the group or master in monitor mode 10 1 2 AUX AFL Press AFL to listen the post level aux mix in the headphones and local monitor without affecting the main outputs The console monitor meters are interrupted with aux group signal The yellow indicator lights to show that AFL has been selected on the master USE AFL to check the signal being sent to the monitors effects or other destination AFL is pre mute so that you can check the signal before sending 10 1 3 REV These switches reverse the function of the group and aux masters the heart of the dual functionality pioneered by us They are recessed to prevent accidential operation Use a pen or pointed object to set their position In the up position flush with panel the group is controlled by the fader and the aux by rotary master This is typical for FOH mode where the faders are used for subgroups feeding the main stereo mix When pressed the aux uses the fader as the master and the group is moved to the rotary control The aux mix is now presented to rear group XLR complete with insert The group mix apppears at the aux TRS jack This is used for monitor mode where the aux are the main mix feeding the stage2. 8 6 GROUP L R M OUT The main console mix outputs are on AUX AUX AUX AUX AUK AUX y electronically balanced XLR These 4 GRP AUX REVERSE AUX AUX 3 DUET s u 6 DEL Ze SP 0 C ee e ee O Ka AD u AQ produce the professional standard 4dBu 1 23V when the meters read 0 and provide to a maximum 25dBu 13 77V The L and R outputs typically feed the house PA system in live sound mixing or a 2 track recorder in studio mixing In monitor mode these outputs reverse with the AUX TRs jack connections 16 45 sius 8 7 AUX OUT 1 6 Each AUX send is available on an AUX AUX AUX AUX AUK AUX 6 impedance balanced TRS jack operating at 2dBu 0 62V line level The Aux senda are typically used to feed monitors effects GRP AUX REVERSE devices such as reverb and delay Each matrix output is available on an impedance balanced TRS jack operating at 2dBu 0 62V line level The matrix outputs are P typically used for mono or stereo recording or broadcast feeds delay and fill speakers zone feeds additional monitors such as IEM hearing assist loops and so on 8 9 MATRIX EXT IN 1 4 Each matrix has an unbalanced 0dBu 0 77V line level TRS jack input An external signal such as ambience mix additional or sub mixer remote source reference tone and so on may be mixed in to each matrix The inputs are normally as shown in the diagram here This means you can plug in just one jack EXT
3. LINE MIC N 4 IN m 7 w e eil WM e N SS f H The LINE PAD switch selects either the MIX XLR or the LINE TRS jack as the input source The XLR is normally through the TRS jack so it can be used for microphone or line level signals when nothing is plugged into the jack socket This gives the channel preamp a massive headroom with 34dB maximum input capability using XLR or jack Both inputs are balanced but can be wired to work with unbalanced signals when required The MIC XLR can be switched to provide 48V phantom power for condensers Note Do not connect unbalanced sources or cables to XLR input when 48V phantom power is selected To avoid loud clicks always turn the channel off by pressing MUTE when switching 48V on or off and when plugging or unplugging cables 8 2 STEREO CHANNEL MIC IN OUT LINE IN MIC OUT OQ 513 8 2 1 STEREO CHANNEL MIC IN Each stereo channel features a mono microphone XLR input and two independent stereo line inputs The balanced MIC input accepts a maximum 14dBu 3 9V and can be switched to provide 48V phantom power 8 2 2 STEREO CHANNEL MIC OUT The output of the mic preamp is available on the MIC OUT BREAKPOINT TRS jack socket This is impedance balanced and operates at a nominal OdBu 0 77V line level Plugging into this socket breaks the signal into the associated stereo channel That means that the mic preamp can be used independently of the chan
4. 11 13 5 Delay UE 38 11 13 6 al popnli en ee seen 38 sius 11 13 7 Additional monitor mixes 0 2 ee eeeeeeeeene eee eect ee eeeaaeeeeeeaaeeeeeeaaeeeeeeaaeeeeeeaaeeeeeeaeeeeeeaaes 38 11 13 8 Combining two consoles into a single PA 38 11 13 9 Create IEM mixes with ambience nenn 39 11 13 10 Using the matrix to create a recording enn 39 11 14 Recording with the mixing Console nnne 39 11 15 Pre post fade Aux settnge Nee 39 11 16 Aux Fed SUDS uite pibe eed eng ba 40 11 17 Creating a separate mix 40 11 18 Other M output applications enne nennen 41 12 Technical E 42 12 Performance etal cda 42 12 2 Connections 2 S 43 13 Girc it diagrams e TE 44 6 45 sius 1 Warranty Limited one year warranty This product is warranted to be free from defects in materials or workmanship for a period of one year from the date of purchase To ensure a high level performance and reliability for which this equipment has been designed and manufactured read this user guide before operating Conditions of warranty Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standard
5. If you recorded the console main output you would be disappointed when you got home and listened to the result For example there may be strong voices acoustic guitar and flute but the drums bass and electric guitar may be low This is because you did not need much of these backline instruments in the PA mix However if you use the matrix to feed the recording you could start with the main LR PA mix then turn up the drum and the guitar groups to compensate for the lack of these in the house system You could also add in ambience as described above to give the recording more life by including audience reaction and natural reverberation 11 14 Recording with the mixing console The console is equally at home recording live or in the studio project The studio grade preamps produce an accurate and noise free recording Create a stereo recording from the main LR output or from a pair of matrices as described above if recording and mixing live at the same time To record to multitrack use whichever combination of groups matrix auxes and channel direct outputs is most convenient The direct outputs are set pre insert pre EQ as factory default This setting means that the recording is not affected by your live fader and EQ changes 11 15 Pre post fade Aux settings The aux sends are switched pre or post fader using two PRE switches on every channel One switch affect auxes 1 4 the one other auxes 5 and 6 It is usual to set auxes pre fade
6. as a common source to all matrix two jacks EXT1 2 as acommon stereo source to matrix pairs or four independent sources This is ideal for adding mono or stereo ambience to recordings or in ear monitor fed from the matrix 17 45 sius 8 10 2 TRACK IN and OUT Unbalanced TRS jack outputs and TRS jack inputs connect to popular recording and playback devices such as CD Minidiscs computers and tape machines Nominal line level is 2dBu 0 62V The 2 track send always follows the post fade LR mix regardless of mode switch configuration The 2 R 2 TRK IN LM R 2 TRK OUT L track return can be used for monitoring a mono or stereo recording o as a simple input for playback of walk in and background music The L input normally through the R socket for plugging in a mono source on a single jack 8 11 MONITOR OUT MONITOR These impedance blanced line level TRS jack outputs follow the post level OUT R mn monitor signal Separate sockets are provided fot the L and R signals Use these to feed local speaker or other monitor systems 18 45 sius 9 Input channel 9 1 Mono a X Yx ME 9 11 9 e LJ m a ax 9 1 1 48V Switches 48VDC to the channel input XLR to powering microphones or DI boxes that need phantom power The power is current limited through 6kO resistors to pins 2 and 3 Warning Do not connect unbalanced sources or cables to inputs with phantom power sel
7. correctly aligned with L and R faders Set the channel aux sends to unity 3 o clock position and release the LR routing switches if you do not want the signal in the LR speaker as well The mixing console gives you the choice of either mixing 40 45 sinus the sum of L and R to the M output mode switch up or an independent AUX6 mix to M mode switch pressed 11 18 Other M output applications Apart from the aux fed subs and C mix described above other examples include L R sum mono fill additional mono zone feed mono recording mono PA with LR providing two subgroups to M ora stereo recording and more 41 45 Camus 12 Technical Data 12 1 Performance Maximum output level XLR 26dBu 15 46V Jack 20dBu 15 46V Meters 3 color LED Master meters 12 segment 30 to 16dB Frequency response 20Hz to 50kHz 0 5dB THD n at 14dBu 1kHz Channel to mix out lt 0 003 Noise rms 22Hz to 22kHz Mic EIN 128dB Residual output noise lt 95dB 100dB S N LR mix noise 16 routed lt 85dB 90dB S N Groups mix noise 16 routed lt 85dB 90dB S N Aux Mix noise 16 routed lt 92dB 90dB S N Mix noise 16 line Gain OdB 86dB S N Mono EQ HF Shelving 15dB 12kHz Peak dip 15dB 500Hz to 15kHz Q HM 18 LM Peak dip 15dB 35Hz to 1kHz Q 1 8 LF Shelving 15dB 80Hz Measurements W D H 661mm 550mm 190mm 42 45 Carus 12 2 Connections Stereo channel ST1 3
8. unbalanced ZA Ce ia pp HEADPHONES er Ring to sleeve ma D 1 Sleeve ground Ring cold balanced Tip hat 1 3 12Y 3 INSERT e 1 44 1 ON Sle eve ground Ring return unbalanced Tip sendl RCA phono jacks adapter RCA phono cable unbalanced das unbalanced instrument cable o MIC cable Sleeve ground ing cold hot 13 45 sius 7 2 Required connection cables The mixing console uses professional grade 3 pin XLR and 14 TRS 3 pole jack sockets To ensure best performance we recommend that you use high quality audio cables and connectors and take time to check reliable and accurate cable assembly It is well known that most audio system problems are due to faulty or sub standard interconnecting leads The following plugs may be used to connect audio to the console XLR female plug TR jack plug XLR male plug TRS jack plug Avoid reversing and on balanced connections as this will result in reserved polarity out of phase signals which may cause signal cancellation effects Where long cables runs are required balanced interconnections should be used However line level interconnections between more affordable 2 wire signal ground unbalanced equipment and the console unlikely to cause the problems if the cables are kept shorter than 10 meters or so Refer to the wiring diagrams in chapter 7 7 3 Dealing with ground loops buzz and in
9. DO K eee 4 ON ee DON ON ON ON ON moe QuE W r M 9 Y y 6 if J ION 4 H 4 4 A 4 4 t OO OW 4 a ee el m m q y LN A Sr e 200 O M OC o gt 2 a ON o OO OOO CC O C 6 e 500 00 O 4 CH ER 4 A gt ER 9 EN 5 Ww X x oe oe oe x x X x X x Ww x x NNN x x x X y n X MH OD i u yl yl i 4 4 DA AA AN AN LAA 4 4 4 D 5 Introduction to the mixing console The mixing console is an analogue mixing console designed for professional audio applications Whether mixing FOH monitors or both recording live or in the studio installed in a busy venue out on the road touring or earning its keep in rental stock the mixing console provides the perfect solution Engineered to the same standards as our top of the range consoles it ensures the highest reliability and finest sonic performance 16 channels LR Main Mix Multi Mode M output 4 Group Sends 6 AUX Sends 7x4 Matrix Proper dual functionality for FOH Monitor mixing Recording capable M can be configured as LR sum C mix Wedge or Aus Fed Sub master Sub grouping with pan control Gain for every channel 2 stereo channel each with mic and dual stereo line inputs Stereo channel line inputs can be assigned independently to LR Responsive 4 band 2 sweep EQ 100Hz channel high pass filter Phantom power Polarity switch Channel and master meters Chanel direct outputs Per channel pre post fader Aux s
10. L and R rotaries to the 2 d o clock position to sum them together You can use the built in 1 kHz tone generator to feed a line up tone to the connected recorder gt 5 D 2 11 13 2 Stereo Recording Raise L to the unity 3 o clock position in one matrix R in another to create a stereo pair that follows the LR mix You can adjust the balance to compensate for the acoustic sound in the room using the groups and even add audience ambience 11 13 3 Remote Broadcast Create a mono or stereo feed as described above Use the tone generator to send a slate signal to the destination for line up You can check your level in the headphones before you send it by muting the matrix and selecting AFL 37145 sius 11 13 4 Zone feeds Send independent relay feeds to additional locations such as the foyer dressing rooms cry room balcony and so on You can use the groups to adjust the balance to suit the destination for example to boost the orchestra against the vocals Feed the output through an EQ to tune the speaker for acoustics 11 13 5 Delay Fill speakers Use the matrix to feed additional fill speakers for distributing the sound more evenly around a large venue e g centre fill stage front fills under balcony or rear fills or mix island delay tower on festivals To aid intelligibility for the nearby listeners without moving their focus from the stage the send should be delayed using an in line
11. Please read it carefully before starting Included is information on installing connecting and operating the console panel drawings system block diagram and technical specification For further information on the basic principles of audio system engineering please refer to one of the specialist publications and resources available from bookshops audio equipment dealers and the internet We reserve the right to make changes on the manual 4 View of the mixing console 4 1 Front view e r uH Ka kee kee e Ae CH db Tere we ner ede tj Ade e re ri X d Siche De QD A4 y Za O me O D 1 CR L LA s eg _ e 4 2 Back view t LT d ms mss zt Di m eo rx M D CO Yir Gen rt u 58 y monu ars de D 24 74 78 ry rr saree amp n n m aot IN M Gw e 58 9 KA es z ac i gt ra ir o Lal sa L x D e fire yey sais L Den TAMTA Js OB bei OF OM em Xia m Xa m Ma m 8 Kay E s E CH y y 7 E un Q E Cee t Fe gt D IT _ IPs fu ui JU 9 45 J LJ gt B U gt J J tJ LJ E J o J x gt J O c OOO Ou 9 10 10 OO 9t Sooo Dl folo O 970 70 7070 7070 0 0 70 0 0 70 0 70 70 QS Rig fala O O XS DO OO xxx
12. and control resolution can be severely degraded In addition it is impossible to mix monitors from FOH in this way as changes to the gain settings affect the monitors too The correct method is to use the GAIN to match the source to the operating level of the channel for optimum dynamic range and then use the FADERS to balance each source into the mix With correct system gain structure prime sources such as vocals would have their faders operated around 0 while sources low in the mix such as backing vocals and acoustically loud brass drums would display their true contribution with their lower fader positions This is a much more visual and accurate way of mixing 11 4 Using PFL AFL We are renowned for bringing you the most comprehensive engineer s monitoring system in consoles at this price point We recognize the importance of correct gain structure and signal handing The mixing console includes LED meters for every input channel and main output as well as a pair of high resolution meters dedicated to monitor duty only In monitor mode the M fader and associated controls become a full featured PFL AFL monitor feed for the engineers listen wedge 32 45 sius The input channels provide PFL pre fads listen so that each source can be checked using the meters and headphones before you bring the fader up You can even use PFL while the channel is muted to prevent the signal reaching the house and monitor speakers until you have ch
13. are widely placed you can reduce the stereo image by reducing the amount of panning each side Whatever image you can create it is important that you listen to the results and consider the listeners at all positions in the room 11 9 Zero the console Before starting the sound check it is good practice to zero the console by setting all its controls to a sensible starting condition Set all the GAIN EQ and PAN controls mid FADER AUX and MATRIX controls off TALKBACK and OSC NOISE levels off and all switches up Make sure that the OSC NOISE generator is turned off 11 10 Turning the system on and off e Turn the amplifiers on last and off first e Mute channels before plugging cables unplugging instruments and switching phantom power e Let equipment which has been stored in damp or cold place acclimatize in the venue first before powering it up e Powers up the system with plenty of time before you start the sound check or show 11 11 Sound levels The ear is a delicate instrument Do not subject yourself or any listener to long periods of loud sound particularly with extreme equalization This may result in frequency selective or full range hearing loss Adhere to the sound level regulations which may apply to the venue and common sense 11 12 Dual functionality The mixing console takes dual functionality a thoughtful stage further with advent of a new engineering practice such as multi media and IEM in ear monitor mixi
14. delay processor As a rule of thumb delay 1ms per foot difference between the listener and the fill and the listener and the main speakers Now add a few milliseconds Haas effect delay so the listeners hear the main speakers slightly before the fill Keep the fill level about 10dB or so below the main PA sound at that location It may help intelligibility to boost the vocals above the instruments in the fills and to use an EQ to cut the extreme LF and HF frequencies 11 13 6 Hearing assist It is a growing requirement that venues provide a hard of hearing inductive loop IR or wireless broadcast for the hearing impaired audience The matrix is ideal for this application as you can combine a stereo LR mix into mono add groups to help vocal intelligibility patch in an external ambience source and add processing such as EQ and limiters which may be needed 11 13 7 Additional monitor mixes You could use the matrix to create some additional monitor mixes when you run out of auxes this time made up from a mix of the groups LR and external input The LR could be used to create a general overall balance and then the groups added according to musician preference Groups could be routed from me only channels associated with each musician or traditionally grouped sources The musician could get a balance from say the overall stereo mix drums brass keyboards me only and ambience a very quick way of mixing 11 13 8 Combining tw
15. monitors You can select any combination for the FOH and monitor mode e g just 3 4 giving you two fader aubgroups two monitor sends on faders and main LR mix Note The groups always feed the matrix and the subgroups controls PAN and GRP TO LR regardless of the mode This means the group mix can still perform a useful function when the console is configured in monitor mode 10 1 4 PAN 24 45 sius Positions the group signals between L and R in the stereo mix when the GRP TO LR switch is pressed Using pan you can create mono or stereo groups positioned as you require in the main mix For stereo grouping set the odd group pan fully to the left and the even group pan fully to the right The centre position mono image is for quick resetting Note that the group mix always feeds these subgroup controls regardless of FOH or monitor mode selected 10 1 5 Meter A 4 LED bar meter displays the post fade group signal FOH mode or aux signal monitor mode REV pressed 10 1 6 MUTE When pressed the group aux signal is turned off This affects the feed to the output XLR LR and matrix The red indicator lights when the channel is muted 10 1 7 GROUP AFL Press AFL to listen to the post fade pre mute group mix in the headphones and local monitor without affecting the main outputs Note that this becomes the aux mix in monitor mode The console monitor meters are interrupted with the group aux signal The yellow indic
16. on that channel Selecting more than one PFL at the same time mixes those signals together in the monitor 9 1 12 Meter A 4 LED channel meter displays the pre fader signal level SIG lights when a signal of 12dBu 0 2V is detected 0 lights when the nominal OdBu level is reached and 6 at 6dBu 1 5V PK lights when the channels pre fade signal within 5dB clipping This gives you enough warning to reduce gain before you hear signal distortion 9 1 13 Routing Press L R to route the channel signal to the main LR mix Press 1 2 or 3 4 to route to the groups Use Pan to position the signal between L R and the odd even group pairs To route to a single group set Pan fully to one side You can route to L R and all groups simultaneously by pressing all switches Check that you have the switches correctly before you start mixing 9 1 14 Fader A high quality 100mm smooth travel fader with protective dust cover controls the channel level feeding the main LR mix groups and post fade aux sends The fader provides 10dB maximum boost above its normal unity gain OdB position 21 45 sius 9 2 Stereo Each stereo channel features a mono microphone preamp as well as two stereo line inputs These three sources can be used independently or mixed together into channel so providing a unique flexibility For example you could configure a conventional mono microphone channel with the two short return stereos routed
17. 0 3 Iz 24 UNE EEUU 24 TONS E 25 TELE MUTE sue ete elek 25 10 1 7 GROUP TEE 25 sinus TIO le EE 25 10 2 AUX 5 6 Master L R M Mlaster recette ettet putet cnet cabras caian 26 ARC EE KEE 26 ARC EE 26 10 23 BL cp 26 10 3 7X4 MAX CT 27 UC EE uu 27 103 2 GRP 2 9 4 ceste teet ca 28 KU DC E E A tree a nde e EUR ier eee oc REPRE RE eee 28 10 34 MEL reellen 28 19a NUl scatena A 28 UH EE E 28 10 4 Monitor Talkback und Signal Generator 29 104A Ugo 29 1A dore T 29 10 4 8 Signal Generator Pink Nolse eere nennen nnn tenens 30 11 Applications and operating Ups 30 SE E 30 11 2 Using the Oscillator Noise Generator 31 11 3 Mixing with faders or gain controls essseesseesseessreerrsrrsrnssrnsstnssrnsrnsstnsstnnnsnnnnnnnnnnnnnnnnn 32 11 4 Using Wd IEN DEER 32 o DECIDO 33 EE E MIC 34 RE PON E 34 11 8 Mixing the PA in mono or teren 34 11 9 STO the COMSONS i e cel 35 11 10 Turning the system on and oft 35 Titi Sot pd Jee Sesgetgrg ai a 35 11 12 Dual funetionallty a ea his hei 35 11 13 Applications for the Matik eisrean aa NA SKN 37 11 13 1 MONO Record trat geesde 37 11 13 2 Stereo RECOLGING DE 37 11 13 3 Remote Broadcast east 37 11 13 4 Vna 38
18. 8 e 6dB boost Note that EXT IN jack sockets are normally linked in a way that lets 1 you plug in a mono or stereo common source to feed all the matrices or an 2 d te independent source to each Plug into EXT1 only to feed one source to all four 1 matrix EXT IN controls Plug L into EXT1 and R into EXT2 only to feed a stereo 2 source to matrix 1 2 and 3 4 J e MATRIX EXT IN mie ot Ve a ct me Some examples include adding ambience sources to recordings and in ear By monitoring adding a direct output or an aux mix to quickly create a monitor from the main mix plus selected channels and linking in another console to feed the same PA in a festival or other dual console situation 27 45 sinus 10 3 2 GRP 1 2 3 4 Mixes in the post fader post mute group mix The rotary provides 6dB boost 10 3 3 L R Mixes in the post fader post mute main LR mix The rotary provides 6dB boost Turn up both L and R to create a mono sum from the stereo LR mix Turn up L in one matrix R in another to create a stereo output from two matrices 10 3 4 Level The master level control fader for the matrix Provides 6dB boost above the normal 0 setting 10 3 5 Mute When pressed the matrix output is turned off The red indicator lights when matrix is muted Mute does not affect the matrix AFL monitoring 10 3 6 AFL Press AFL to listen to the post level matrix mix in the headphones and local monitor without affe
19. RR Res 8 10 2 TRACK IN and QUT niet epi eter ae aid arena 8 11 MONITOR OUT p 9 Input Channel ee esas eis Lee ete O NEE 9 1 MONO 9 1 1 48V an i roi bs RO dede tepido co e vc ee ane baud 9 1 2 Nol neresi id o era Table of contents 3 45 sius 9 1 3 Line PAD C 19 9 1 4 erp P 19 9 1 5 ult ET 20 9 1 6 com 20 9 1 7 AUX SOMOS 20 9 1 8 oce 20 9 1 9 PAIN pep A M 20 9 110 MUTE iint tette hit ee ee 21 Gau NNEN cR 21 CAR Meter EE 21 91 13 AQUINO 21 CIE St EE 21 AS A 22 9 2 1 MiG INPUT clan aladdin cdas 22 9 2 2 Dual stereo line Inputs un ee a ux n 22 9 2 3 Routing mode switch EE 22 9 2 4 co Ses eee ee a est id wes es ee 23 9 2 5 AUX SOMOS ea M 23 9 2 6 EBA 23 9 2 7 ig cse 23 9 2 8 age gr E A E E AE 23 9 2 9 Meter E R a ee ee ee ee 23 9 2440 AQUINO nen eere cn a as 23 MEE EE 23 10 Master SECON PERPE 24 10 1 Gro p Aux IECIT E Rm 24 101 AUX MasterS er nme ii 24 10 412 DS dM 24 1
20. SIRUS PRO Manual Mixer Live M416 sius 2 45 sinus 1 Warranty PENES CATONE 2 1 FOR SAFE AND EFFICIENT OPERATION sess ennt 2 2 Important mains plug wiring instructions sseesssseeeenen enn 3 MIO Dea g E 3 1 FOP WOM e E M 4 View or the mixing console cerit einn ee ea ee 4 1 Front VIS Weir LM LL SV oa 4 2 Back OW oit htm e EI tia din EMI e 5 Introduction to the mixing console eene eene nennen nennen nnne 6 Installing tlie Console coner tete tete bike terit tesa o tutu te deol nina awe m PEN ET elle Une DEE 6 2 Switching the console on or oft 7 Audio cometon E 7 1 General overview entered dees 7 2 Required connection cables 2220ummnnnsnannnnnnnannnnnnnnnnnnnnnnnnnnnnnannnnnnnannnnnnnannennnnannnnnnnannnn 7 3 Dealing with ground loops buzz and interference 0 0 0 ee eeeeeeeeneeeeeeeaeeeeeenaeeeeeeaaeeeeeeaaes 7 4 Balanced Keele le LEE 8 Connections at the mixing console sess ennt enne nn 8 1 MONO CHANNEL MIC LINE IN 8 2 STEREO CHANNEL MIC IN OUT UNEIN nennen 8 2 1 STEREQ CHANNEL MIG IN ee 8 2 2 STEREO CHANNEL MIC OUT enne 8 2 3 STEREO CHANNEL LINE IN 80 INSERT oca Ee Een een MP ized T iaa 8 5 LAMP LE 8 6 GROUP LER M OUT ecos BE AS EU Diao a a aaa iia ia iii 8 8 MATRIX OUT 1 4 tees bunte ex Le gaag ba ust e ii E 8 9 MATRIX EXT IN 124 oi iet aa Ex ana yx ege deepen x
21. TRS unbalanced gt 10kQ 16 to 20dB ST2 4 TRS balanced gt 10kQ 16 to 20dB 2 track return TRS unbalanced gt 4kQ 2dBu 0 62V TRS Tip Send Ring Return OdBu 0 77V TRS Tip Send Ring Return 2dBu 0 62V Inserts Channel Output lt 750 4dBu 1 23V 26dBu 15 45V Groups aux out XLR balanced Pin 2 hot max Direct out TRS impedance balanced lt 750 OdBu 20dBu 7 75V max Headphones TRS Tip L Ring R 30 to 6000 headphones recommended Lamp 4 pin XLR Max 12V 5W lamp 43 45 en T a nn E 3 EZE ta 4 tze otoo o zl ner INN 44 We ki sae a O GROUPS AJX 1 4 2E n Hit 1 H L IR IE I LIA ec 0 d bed E t Y tb gt Zen o e um SS en LIF AUX 5 6 f SES ww y o UR De ur e Y PIC RP M a zone Or ue 3 O3 Le em o d ep MIC STEREO INPUTS iagram PRO t di 5 e ircui C SIRUS 13 k r M am Ae De CH are renra D 4 amp E a EN cc v gt Qrt o an 44 45 aas Importer B amp K Braun GmbH Industriestra e 2 D 76307 Karlsbad www bkbraun com info bkbraun com X RoHs m en 45 45
22. ailable to all the main outputs Plug in suitable cable or gooseneck microphone A good quality dynamic or condenser vocal microphone is recommended Note that 48V phantom power is available at the XLR as standard Warning Do not connect unbalanced sources or cables to inputs with phantom power selected To avoid loud clicks do not press the TALK switch when plugging or unplugging the talkback microphone First select the source you wish to talk to You can select the auxes in pairs usef7ul for communicating with the performers on stage The four groups are selected simultaneously ideal for identifying a multitrack recording You can also talk to LR ideal for announcements to the audience Once selected press and hold TALK to route the mic to the required destination Adjust the talkback level using the TRIM control below the TB and mic XLR Pressing TALK automatically dims the level of the signal generator if it is turned on 29 45 sinus 10 4 3 Signal Generator Pink Noise Press to select either pink noise up position or a 1 kHz sine wave tone as the test source Start with the trim control turned fully down The generator ON switch is recessed to prevent accidental operation Press this with a pen or pointed object The green indicator lights to warn the generator is enabled The generator signal is routed to any source selected on the switch bank above the TALK switch Use the signal to test the loudspeaker system and the l
23. ame as your local supply Check that the correct mains lead with molded plug has been provided with your console Make sure that IEC mains plug is pressed fully into the panel socket before switching on 6 1 Grounding The connection to the ground in an audio system is important for two reasons 1 Safety To protect the operator from high voltage electric shock 2 Audio performance to minimize the effect of ground earth loops which result in audible hum and buzz and to shield the audio signals form interference For safety it is important that all equipment grounds are connected to mains ground so that exposed metal parts are prevented from carrying high voltage which can injure or even kill the operator Do not disconnect the ground connection in the mains lead 11 45 sius 6 2 Switching the console on or off Turn power amplifiers off before switching the console and any other connected equipment on or off Note Turn amplifiers and powered speakers on last and off first To turn the console on press the ON OFF switch next to IEC mains input socket To turn the console off press the switch again T Audio connections 7 1 General overview Output INPUT ALA Male socket XLA Female socket 1 Pin 2 hot l zrnund 2 hot 2 hat 1 d West RG Zu u o wm XLR female plug 3 cold 3 Kd XLR male plug unbalanced unbalanced Set ILE P Les m 1 cimi n 4 an SS VP x 12 45 INPUT OUTPUT
24. and reduced dynamic range and therefore audible residual system hiss 11 2 Using the Oscillator Noise Generator The mixing console includes a useful signal generator able to produce a pure 1 kHz sine wave tone or pink noise test source This is invaluable in testing the system components and setting up the correct gain structure The generator can be routed independently to the various console outputs Use the 1 kHz to line up the connected equipment For example a recorder video camera or broadcast feed from the matrix Route the tone to the groups and turn up GRP1 in the matrix Set the matrix GRP1 and LEVEL controls to their 3 o clock 0 positions Press the matrix AFL and adjust the oscillator level until the console monitor meters read 0 Next adjust the recorder input trim so that its meters also read 0 The recorder is now correctly aligned to the operating level of the console Similarly you could match the console LR output to a DSP speaker processor by sending the tone LR setting the faders for output meters reading 0 and then trimming the processor input for 0 on its meters To prevent a loud tone through the speakers it is best to do this with amplifiers turned off 31 45 sinus Use the Pink noise generator to check the signal routing and loudspeaker response Pink noise is a random signal that contains all audio frequencies and is therefore a very good test source Unlike with white noise which h
25. annels faders and are typically used to send a proportion of the channel signal to an effects device such as a reverb or delay Note that post fade sends may be preferred when the console is configured in monitor mode so that the faders become masters for all monitor mixes Pr or post fade sends may also be used for special applications such as recording zone feed clean feed and aux fed subs or centre speaker 9 1 8 PRE When pressed the pre fade channel signal is sent to the associated aux When it is released the post fade signal is sent Aux 1 to 4 and 5 6 are grouped for pre post switching Default setting is pre insert pre EQ so that inserted compressors and EQ do not affect the sends when mixing monitors from FOH 9 1 9 PAN Positions the channels signal between L R in the stereo mix 20 45 sinus 9 1 10 MUTE When pressed the channel signal is turned off This affects the feed to LR mix pre and post fade aux sends and direct output but does not affect the insert send The red indicator lights when the channel is muted Always mute the channel when switching phantom power or plugging the cables and Sources 9 1 11 PFL Press PFL to listen to the pre fade channel signal in the headphones and local monitor without affecting the main outputs The console PFL AFL active red indicator lights and the monitor LR meters display the channel signal The PFL switch yellow indicator lights to show that PFL has been selected
26. as an equal energy per HZ and sounds like system or inter band tuner hiss pink noise has equal energy per octave a response that matches the logarithmic way our ears perceive sound You can hear all frequencies clearly from deep bass through mid to treble This means you can route the noise to a speaker system and quickly hear if one tone of the sub mid or HF drivers is faulty With the noise sent to several speakers at the same time you can listen for comb filtering effects and the severe phasing effect which indicates that one of the speakers may have its wires reversed Pink noise is also used with an RTA real time analyzer when measuring room frequency response Testing a system with pink noise through the speakers is often referred to as pinking the room The mixing console signal generator is an invaluable tool for calibrating and testing the system during setup To prevent any unexpected mishaps during the sound check or show remember to disable it by releasing the recessed ON switch once you have finished the testing We also advise that you always start the calibration with the OSC NOISE trim turned fully off so that you can bring up gradually without the risk of overloading the destination 11 3 Mixing with faders or gain controls There is a technique used by some operators where they set al the faders to 0 position and balance the mix using the channel gain controls We do not advise this method as the signal to noise ratio
27. ator lights to show that AFL has been selected on that master 10 1 8 Fader A 100mm a smooth travel fader controls the group mix output level Note that it becomes the aux mix master in monitor mode REV pressed The fader provides 10dB maximum boost above its normal unity gain OdB position 25 45 sius 10 2 AUX 5 6 Master L R M Master rt en 10 2 1 AUX 5 und 6 Master aa ua These functions in the same way as described for auxes 1 to 4 In monitor L mode the recessed REV switch reverses the AUX5 master with L and Ld 27 a AUX6 with R Here the aux signals are presented to the Land R XLR E d E 3j outputs complete with their inserts The LR mix swaps on to the Aux TRS La en mm jack outputs Note that the LR mix always feeds the matrix and 2 track regardless of mode selected 10 2 2 LR Masters Separate 100mm faders control the main mix L and R output levels They provide 10dB maximum boost Each master includes a 4 LED bar meter an AFL switch and a MUTE switch so that L and R can be separately monitored and muted This is most useful in monitor mode where these masters carry the AUX5 and AUX6 signals 10 2 3 Master A 100mm fader adjusts the level of the signal to the M output XLR The master is fully featured and includes a 4 LED bar meter an AFL switch and a MUTE switch The M outputs add a true touch of genius to the versatility of the mixing console The source is selected using two
28. ce For sources you wish to send to the sub turn up the channel aux send to its unity 3 o clock position Avoid the temptation to ride the aux send to create mono or less sub as this may upset the natural speaker balance or cause problems for listeners in different parts of the room One problem with using the aux in this way is that it becomes difficult to balance the top and sub speakers if you need to adjust the overall volume of the PA Typically the LR tops uses fader masters and the aux is on rotary master The mixing console overcomes this with an innovative mode switch above the master faders that routes the AUX6 mix master through the M fader and on to the XLR output This switch is recessed for protection against accidental operation The result is you get three master fader aligned for simultaneous control individual mutes AFL and meters and three properly balanced XLR outputs Note that the AUX6 rotary master does not affect the sub feed IT does however independently affect the AUX6 jack output This gives you a further advantage that another sub can be separately controlled using the rotary master for example to supplement the stage monitor mix 11 17 Creating a separate C mix As with the aux fed sub mix described above you can set the mode switch to create an independent mix feeding a dedicated centre or mono speaker The channel AUX6 sends become the routing to this mix while the M fader with XLR output becomes the master
29. correcting for reverse wired cables correcting for microphone placement problems mixing two mics on a snare drum one above the other below where diaphragms move in opposite directions and helping to reduce comb filtering effects as radio miked actors perform close to each other Polarity is sometimes labeled phase on mixing consoles Technically phase is not the correct term as it implies a 180 degree time shift Polarity simple reverses the wires It does not affect time Before starting your mixing check all the channel polarity switches are correctly set normally up 11 8 Mixing the PA in mono or stereo 34 45 sinus Because a console provides an L and R output does not mean you have to mix in stereo It is often convenient to have a separate fader control processor inserts and outputs to drive two mono speaker stacks in an FOH system How much stereo you introduce into your mix depends on where you position the pan controls In most situations the size of the room and the position of the speakers makes stereo mixing an advantage only for a small section of the audience usually those around the sound operator Those listening near the speakers are likely to lose information from the opposite stack For this reason it is the best to mix most sources in mono pan centered However it can enhance the image by mixing some ambient sounds in stereo e g reverb returns keyboards and special effects Where the speakers
30. cting the main outputs The console monitor meters are interrupted with the matrix signal The yellow indicator lights to show that AFL has been selected on that master Note that MUTE does not affect the AFL function This means that you can check the matrix signal while its output is muted 28 45 sius 10 4 Monitor Talkback und Signal Generator c o 229 40 4 1 Monitor a TN ng a Comprehensive engineer s headphone and local monitoring is provided Select reaps amp either LR 2 track return as the default source using the L R 2 TRK switch me I Pressing PFL or AFL elsewhere on the console automatically overrides the d EE current monitor source with the signal from the channel or master section The Qu Sie red PFL AFL active indicator illuminates and the console meters display the nn SE active signal al e ye The console monitor meters provide 12 LED indicators to accurately display the E or signal level of the selected monitor source Reduce the gain or level ifthe red 16 peak indicator lights For optimum performance the signals should be adjusted to read an average 0 with loudest peaks reaching around 6 Warning To avoid damage to your hearing do not operate any close to ear monitoring such ad headphones for long periods at high volume Continued exposure to high volume sound can cause frequency selective or wide range hearing loss 10 4 2 Talkback Individually assignable talkback is av
31. direct to LR for effects Alternatively you could patch the mic stage as an independent preamp for an ambience microphone feeding a recording or for a system calibrate microphone while ST line inputs mix two external stereo effects processor return or sound effect players via a single channel This can be useful in saving chennel letting you mix many inputs in a small space Of coursek one stereo could feed the chennl the other route direct to LR Two stero channels could be linked so that the mic premps cross patch to provide one stereo mic and one stereo line channel with two short returns also available 9 2 1 Mic input Similar to the mono channel microphone preamp without the line pad and polarity switches Gain and 48V phantom power switching are included A rear panel mic out breakpoint socket is provided so that the mic stage can be used independently Plugging a jack into the mic out socket breaks its signal path to the stereo channel 9 2 2 Dual stereo line inputs Each stereo channel has two stereo inputs which can be used separately mixed together or split so that one feeds the channel the other routes direct to LR ST1 and 2 feed channel 15 23 ST3 and 4 feed channel 16 24 The L input signal is normally through the R input socket so that a mono source may be plugged in to feed both left and right sides of the stereo channel Each input has its own level control to adjust from fully off to 16dB gain Centre po
32. ecked it and are ready All the main aux and matrix outputs provide AFL after fade listen so that you can check the exact level leaving the console Once again the AFL switch gets its source before the output mute switch so that you can check the signal before you send it to its destination This can be very important when you are feeding remote destinations such as broadcast and recording 11 5 Decibel The Bell is the unit of sound level Decibel is 1 10 Bell a more conveniently sized unit dB 20 log V Vi where Vs and V are two signal voltages in and out ignoring the impedances The dB is used to express the relationship between two levels chosen because of the logarithmic way our ears respond to sound The dB relates one level to another For example a preamp with a gain of 40dB 100x would produce an output of 10dBu for an input of 30dBu Several audio standards exist to relate a signal level to a known reference Audio engineers need to deal with a variety of equipment standards for example a 10dBV CD player plugged into a console with 4dBu 1 23V outputs connected to a OdBu input DSP speaker manager or an operator using an SPL sound pressure level meter to measure sound intensity dBu relative to 0 775Vms professional standard OdBu 0 775V 4dBu 1 228V dBV relative to 1Vms consumer audio standard OdBV 1V 10dBV 316mV 8dBu dB A Sound pressure with a filter contour to approximate the response of the
33. ected To avoid loud clicks always mute the channel before switching 48V on or off and when plugging or unplugging microphones 9 1 2 Polarity Reverses the polarity and connections of the input source Useful when you are using the above below mic technique for example when take a snare drum with two microphones or for correcting mic placement and cable wiring errors 9 1 3 Line PAD Press the switch to select the channel TRS jack line input Release the switch to select the XLR Mic input The XLR is normal through the TRS socket With nothing plugged into the line input the switch therefore becomes a Pad for the Mic XLR It attenuates the input signal by 20dB for connection to high level microphone or line sources This gives the mic preamp a massive 74dB range and headroom of 34dB to deal with the hottest signals 9 1 4 Gain Adjusts the input sensitivity to match the connected source to the internal OdBu 0 77V operating level of the channel Provides a variable 54dB range from dB to 60dB gain mic or 14dB to 40dB line padded mic The gain should be set so that the channel meters average 0 with the loudest moments lighting 6 Reduce gain if the red peak indicator lights Important note on setting channel levels Use PFL to set the gain controls before correct signal level through each channel The main LR meters provide a high resolution display of the channel signal level Use the faders to bala
34. human ear Three curves A B C exist for different loudness dBfs relative to signal maximum before clip full scale 33 45 sius dB Tech Talk P Input signal power P Output signal power dB 10 log P P 10 log V R V2 R If input and output impedances R and R are the same then dB 20 log V V dBm is defined as 1mW into 6000 0 775V dBu 0775V 11 6 Using Inserts The mixing console channel inserts operate at OdBu 0 77V the output inserts operate at 2dBu 0 62V In practice this makes little difference as long as the inserted equipment is intended for the line level operation 6 0 39V to 4dBu 1 23V Simply set the gain through the device to unity OdB with the bypass switched pressed if available With the effect switches in use the console channel gain control to make any further adjustment needed This keeps the gain structure correct through the channel signal path With nothing plugged into the insert the channel signal is routed through a switching normalling contact in the socket As soon as a jack is plugged into the socket the contact is opened and the signal path broken so that the external device can be patched in series with the signal 11 7 Polarity Refers to the positive and negative wires of a loudspeaker or balanced audio connection The console input channels include POLARTITY switches which reverse the and input connections Some applications include
35. if you are mixing monitors from FOH Set post fade for auxes used as effect sends zone feeds aux fed subs and so on If you are using the console to mix monitors only than auxes are typically set post fade so that the 39 45 sinus channel fader becomes the source master to all monitors In this case start with all channel faders set to 0 11 16 Aux Fed Subs Driving the PA system sub bass speakers with their own mix has two main advantages First the mix is much cleaner because only sources that generate the low frequencies e g kick drum bass guitar and keyboards are sent to the subs Low frequency bleed from these sources into open microphones such as vocals and snare is eliminated from the PA much more effectively than using just channel filters Second the subs bass amplifier is only working with the sources needed It is not wasting power reproducing unnecessary pickup The sub can be separately driven in several ways for example using in a group a mono or C bus or using an aux Using an aux send has become a popular method on the smaller consoles Simply feed the LR to a stereo crossover to drive the top speakers and a post fade aux send to a mono crossover to drive the sub speakers Refer to the speaker manufacturer for recommended crossover frequency usually within the range 80HZ to 120Hz Align the system so that the normal unity gain position of the channel fader and aux send result in the correct speaker balan
36. in the audio chain typically a speaker processor such as a limiter or crossover or straight to the amplifier The amp boosts this signal to tens of volts to move the speaker cones so producing the audible sound To get the best performance from your system it is important that you set up the gain structure correctly within the console and also within and between the connected equipment Ideally each circuit should be set to clip at the same time if the signal become too hot in other words each would have similar headroom relative to its nominal operating level The resulting dynamic range is the difference between the highest noise floor and the lowest headroom through the system The performance is only as good as the weakest link The mixing console provides comprehensive metering to check every point within the console signal path Use the channel meters and PFL AFL system to set the gains and mix levels to average around 0 meter reading with usual peaks around 6 Reduce the gain if the red 16 or PK indicator lights Use the equipment meters to set each item within the system path to operate at its nominal level We advise that the processor or amplifier trims are so set that the console outputs can drive up to their nominal 0 level It is a common mistake to set amplifier trims to maximum sensitivity when this results in the console master faders being operated at very low positions with low meter readings
37. ineup connected equipment Pink noise is useful for quickly testing the full range frequency operation and phasing polarity of loudspeakers The 1 kHz tone is better suited to lining up equipment with the steady reading on the meters Warning We recommend you turn off the signal generator once you have finished using it to test and line up your system This will prevent accidental operating during the show 11 Applications and operating tips The following is a collection of brief descriptions application notes hints and tips to help operator understand some of the technical terms referred to and to get the most out of the uniquely capable mixing console live sound mixing console They are written as a concise reference to spark your imagination to creatively and effectively deal with the many challenges now faced in modern day mixing 11 1 Gain structure The term used to describe the gain level matching of the signal through the audio system chain Each item in the equipment chain has its own optimum nominal operating level determined by its electrical circuits If you overload it with a signal that is too high then its output tries to produce more voltage than its power rails can provide resulting in harsh sounding distortion as the audio signal is clipped If you work with a signal that is too low then you are likely to hear residual hiss of the circuits as the noise floor is amplified along with the signal The optim
38. l way to feed the main top speakers In addition route sources with low frequency content such as kick drum bass keyboards sound effects to the sub speakers by turning up the AUX6 send rotary on those channels Make sure all channel aux 5 6 sends have been set for post fader operation Use two crossovers one for the stereo LR mid top frequencies and the other for the sub feed Set the system up so that the correct balance between tops and subs is achieved when the channel send is at it 0 3 o clock position and the L R and M faders in line with each other AUX Fed Centre Mode The same principle as above but AUX6 is used to feed a centre mix such as a fill or C in a LCR system To route to C only turn up the channel AUX6 send to 3 o clock unity position and turn off its assignment switch to LR 10 3 7x4 Matrix m The matrix adds to the powerful multi tasking capability of the mixing console It E i e provides a set of 4 additional console outputs It is a mixer within a mixer a 1 qe creating its output from any combination of the groups main LR mix and external p input It can be used to provide duplicate main outputs or to create new mixes a Cha from these outputs The matrix controls are positioned conveniently away from E the live performance controls to avoid accidental operation A Aa Sys 1 Je 10 3 1 EXT IN TaT a r c Mixes in an external nominal OdBu 0 77V line level source The rotary provides Se
39. mode switches above the R fader These are recessed to prevent accidental operation Use a pen or pointed object to set the position FOH Mode With both switches in the up position flush with the panel the post fade L and R mix are summed together to provide a mono source Use this to feed a mono PA fill delay or zone speakers or even a mono broadcast or recording send Monitor Mode Press the upper switch to create an engineer s monitor listen wedge feed from the AFL PFL mix Note that in this mode the M AFL switch is disabled It is common to use a wedge speaker of the same type used on the stage to listen to and check the various monitor mixes being sent to the performers Together with the group aux REV function the mixing console can be configured as compact yet fully featured monitor console AUX Fed Subs Mode Press only the lower switch to configure M as the master for AUX6 This innovate feature is ideal when driving your sub bass speakers with their own mix fed from an aux a technique becoming more popular in FOH mixing This mode provides all the main PA masters L R 26 45 sius and SUB with faders meters MUTE and AFL Using these faders you can adjust the level of the main PA without losing the balance between the tops and subs The signal is not affected by the AUX6 rotary master However the rotary output can still provide another sub feed with its own independent master control Route all sources to LR in the usua
40. nce each signal in the mix To ensure optimum 19 45 sus gain structure we do not recommend the practice of setting the faders to 0 and mixing using the gain controls 9 1 5 HPF Switch the channel high pass filter on This attenuates frequencies below 100Hz by 12dB per octave The filter is pre insert pre EQ Select the HPF to reduce low frequency noise such as microphone popping stage noise and tape transport rumble 9 1 6 EQ A responsive 4 band semi parametric EQ provides independent control of four frequency bands HF and LF are shelving filters which affect high frequencies above 12 kHz and low frequencies below 80Hz respectively HM and LM are bell shaped peak dip filters which affect frequencies around a centre point which can be swept from 500Hz to 15 kHz and 35 Hz to 1 kHz respectively These have a width Q of 1 8 which provides effective control for both creative and corrective equalization 9 1 7 AUXSends These rotary controls adjust how much channel signal is mixed to the aux outputs Each of the 6 aux has its own control The adjust from fully off to 6dB boost Unity gain OdB is marked at 3 o clock position Aux 1 4 5 6 are switched pre post Pre fade aux sends are not affected by the channel fader movements These are typically used to feed stage monitors In most cases users also prefer that the monitor sends are not affected by inserted processors or the channel EQ Post fade aux sends follow the ch
41. nel 15 45 sius 8 2 3 STEREO CHANNEL LINE IN Stereo inputs ST1 and ST2 feed channel 15 and ST3 and STA feed channel 16 respectively or can be routed directly to LR These inputs use TRS jacks ST1 3 are unbalanced ST2 4 are balanced Unbalanced inputs automatically connect the TRS ring to ground when working with balanced sources The L input is normally through the R socket to accept mono signals on a single jack 8 3 INSERT A single 3 pole TRS insert jack carries the unbalanced insert signal e iP for each mono channel and main mix output Tip send ring TT RETURN zeen l eturn Sleeve common ground The channel inserts are post tia HPF pre EQ and operate at 0dBu 0 77V The group AUX and LR era Co mix inserts are pre fader and operate at 2dBu 0 62V Use these to SEND IN patch in line level signal processing equipment such as compressors outboard EQ delay units and so on The wiring of a suitable cable is shown in the diagram 8 4 DIRECT OUTPUT Each mono channel direct output is available on an impedance balanced TRS jack providing a line level signal operating at OdBu 0 77V The output is set pre fade 8 5 LAMP m The console has one 4pin XLR socket to plug in standard 12V gooseneck lamps to e D illuminate the operating surface when working in a dark environment Only use the lamps intended for this purpose We recommend the LED lamp with cool white CO LED illumination and a built in dimmer
42. ng and computer based live multi track recording The key principles of dual functionality are FOH Monitor The same console can be quickly configured by the operator for proper FOH or stage monitor mixing or as combination of both for mixing monitors from 35 45 Camus PRO Protected AUX Reverse Master Control XLR Inserts Pre Post Sub Grouping Matrix Feed Listen Wedge Talkback Ambience FOH In either mode no part of the console is redundant Every control and socket can be used for an associated function To prevent accidental operation during the show the configuration mode switches are safely recessed under the panel In FOH mode the groups and LR are the main outputs while in monitor mode the aux mixes become the main outputs The REV switch swaps the group or L R master controls with the related aux master so that you have full fader control of the appropriate main output complete with mute AFL and LED bar meter In Monitor mode the aux outputs are routed to the console main XLR sockets for electronically balanced drive with inserts for patching in processors such as graphic EQ limiters and delays Channel pre post switches and link options are important In Monitor mode it must be possible to switch all auxes post for channel fader mastering For Monitors from FOH the pre insert pre EQ or post EQ option is needed In Monitor mode the groups continue to feed the sub grouping t
43. o LR so that you can still work with grouped level control to the main mix In monitor mode the groups and LR continue to feed the matrix so that you can create independent mixes in addition to the auxes for special feeds recording and further mono or stereo in ear monitors In Monitor mode the M output becomes the engineers listen wedge feed providing the PFL AFL mix It gives the engineer identical fader control and XLR drive for all wedges including their own In both modes assignable talkback is provided the matrix has a useful application in both modes External ambience sources can be mixed in to the matrix to create live recording and in ear monitor mixes 36 45 sius Monitor Recording 10 Monitors Stereo Mono 6 Aux Wedge 2 Track 4 Matrix IEM 4 Groups Engineer s Wedge 4 Matrix Ambience Direct Outputs Talkback Ambience 11 13 Applications for the Matrix The matrix is a mixer within a mixer a versatile toolbox of outputs you can use to satisfy a host of applications Using combinations of the outputs you can create mono stereo or zu d L T Ay multiple output mixes a LA SH A 11 13 1 Mono Recording 8 78 ya its pity yey x i RS e If you are working with a stereo PA you can combine L and R X n into a matrix output to produce a mono mix feeding a recorder m 2 PE OT ye ge video camera or so on Raise the
44. o consoles into a single PA In a festival situation you may have a support band wishing to patch their own console One way to do this is to feed the PA from a pair of matrices and then use EXT inputs to combine the external console with the main LR mix 38 45 sinus 11 13 9 Create IEM mixes with ambience In Monitor mode the matrix continues to be fed with the 4 groups L and R mixes You can use these to create additional independent monitor mixes Together with the auxes these give you as many as 10 mixes Create mono or stereo in ear monitor feeds using single or paired matrices for example MTX1 2 and 3 4 You could use LR to start with a basic stereo mix and then add up to four instruments or more me groups Add ambience using a pair of jack leads to patch the stereo channel MIC outputs 15 and 16 into matrix EXT IN 1 and 2 With nothing plugged into EXT IN 3 and 4 the two mix signals are automatically linked across making the same stereo ambience available to both IEM mixes Alternatively you could use an outboard reverb effects processor fed from a post fade aux send to create the ambience Use the channel faders and pan to create the basic stereo mix Remember to set the other monitor aux sends to pre fade 11 13 10 Using the matrix to create a recording The band may be acoustically loud in the room and you need only mix vocals and some of the instruments into the PA to get good clarity and overall balance for the listeners
45. s 2 Safety instructions e Read the safety instructions and also this manual carefully e Keep the manual e Observe all red flags e Observe the manual e To prevent fire or electric shocks protect the device against rain and humidity e Pull the plug before opening the housing e To prevent an electric shock you should not remove the cover e Do not operate the device in the near of water e Use only adry cloth for cleaning 2 1 FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 32 F 0 C or exceeding 104 F 35 C To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt Pull the plug before cleaning 7 45 sius If out of work contact sales agency immediately Any troubles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the device for an extended period of time be sure to disconnect the plug from the receptacle Ventilation It is not allowed cover fan
46. s and air in and outlets Safety Do not remove the grounding It is for your safety If you remove the grounding it can cause electric shocks Hearing To avoid hearing damages you should not operate a sound system with high levels This applies to monitor systems which are in the near of the ear headphones or IEMs also 2 2 Important mains plug wiring instructions The console is supplied with a molded mains plug fitted to the AC mains power lead Follow the instructions below if the mains plug has to be replaced The wires in the mains lead are colored in accordance with the following code CIT Wire Color European USA Canada L Live Brown Black N Neutral Blue White PE Earth GND Green Yellow Green The wire which is colored green and yellow must be connected to the terminal in the plug which is marked with the letter E or with the earth symbol The appliance must be earthed The wire which is colored blue must be connected to the terminal in the plug which is marked with the letter N The wire which is colored brown must be connected to the terminal in plug which is marked with the letter L Ensure that these color codes are followed carefully in the event of the plug being changed 8 45 s rus 3 Introduction 3 1 Foreword Welcome to the professional mixing console of the latest generation of the popular series of dual function live sound mixing consoles We have tried to keep this user guide brief and to the point
47. sition is unity OdB gain 9 2 3 Routing mode switch Recessed to prevent accidental operation In normal up position the ST signal mixes into the associated stereo channel When pressed the signal is routed direct to the LR mix instead of the channel 22 45 sinus 9 2 1 EQ Similar to the mono channel but the twp peak dip mid bands are fixed at 250Hz and 2 5 kHz centre frequencies 9 2 5 AUXSends These work as described for the mono channel but the L and R sides of the stereo signal sum together to feed each aux in mono 9 2 0 BAL It balances the level of the L signal against the R signal to compensate differences in the source or to position the signal within the stereo image 9 2 7 Mute When pressed all the channel pre and post fade signals are turned off except the mic out and any stereo routed direct to LR 9 2 8 PFL Press PFL to display summed L R pre fade channel signal on the monitor meters and listen to it in the headphones and local monitor without affecting the main outputs 9 2 9 Meter The same as the mono channel but the left and right signals are summed together 9 2 10 Routing The same as the mono channel but routes the left signal to L and odd groups right signal to R and even groups 9 2 11 Fader The stereo fader provides 10dB maximum boost above is normal unity gain OdB position 23 45 sius 10 Master section 10 1 Group Aux Masters 10 1 1 AUX Masters
48. terference For optimum performance all audio signals should be referenced to a solid noise free ground earth point frequently referred to as the star point or clean earth A ground loop is created when potential differences exist between grounds at different points in the system and the signal has more than one path to the ground In most cases ground loops do not result in audible problems Should you experience hum or buzz caused by a ground loop check first that each piece of equipment in accordance with the instruction manuals Important For operator safety do not remove the ground earth connection in the power lead of the console or connected equipment To avoid interference pickup keep audio cables away from mains power units and cables lighting cables dimmer units computer equipment and mobile phones Where this cannot be avoided cross the cables at right angles to minimize interference 14 45 Crus IRUS PRO 7 4 Balanced connections A differentially balanced connection hast two signal wires hot and signal cold and a shield The signal source generates positive going polarity down the wire and negative polarity down the wire The destination input stage accepts the signal on its non inverting input pin but it inverts the signal adding it to the signal The result is that the wanted signal is boosted 8 Connections at the mixing console 8 1 MONO CHANNEL MIC LINE IN
49. um operating level is the point at which the signal high enough above the noise floor is amplified along with the signal The optimum operating level is the point at which the signal is high enough above the noise floor so that the hiss is not to heard good signal to noise ration the SNR yet provides enough space headroom before clipping to allow for the louder dynamic musical movements without distortion Dynamic range specifies the maximum range between noise floor and clipping It is the sum of SNR and headroom The larger the figure the better less noise more headroom more forgiving to wide ranging signals A microphone produces a very tiny signal for example 50dBu a few mill volts This should be amplified by the channel preamp to the optimum operating level of the console circuits around OdBU 077V well clear of the noise floor typically less than 90dBu and with good headroom 30 45 sius typically clipping at greater than 20dBu 7 74V With a channel routed at unity gain from preamp input to main output the mixing console boasts a massive 116dB dynamic range The signal can pass through many stages which affect its level within the console the channel its EQ fader pan a group mix and its fader on to the main LR mix with its master fader through the matrix and of course any inserted equipment The output XLR provides the professional standard 4dBu 1 23V nominal level to the next stage
50. witching 10 45 sius e Mutes on all fader meters e 100mm dust protected faders e Assignable talkback e 1kHz oscillator 7 pink noise generator e 2 Track monitoring and replay to LR e Headphones and local monitor outputs e Dedicated stereo monitor meters e Electronically balanced XLR outputs with 26dBu 15 5V drive capability e Preamp 34dBu 38 9V maximum input capability for mic or line e Metal jacks gold plated XLRs sealed pots and switches e Solid copper bus grounding 6 Installing the console The mixing console has a space saving compact chassis design The control surface has a 10 degree slope for optimum visibility during operation The rear connector panel has a split angle design for ease of plugging and unplugging the connectors The console has rubber feet fitted for free standing operation on a flat surface Make sure the surface is well supported stable and big enough for the console to slit securely on all its feet Do not obstruct the ventilation openings on the top and rear surfaces To avoid audible hum buzz or other performance degradation do not place equipment that radiates strong electromagnetic fields such as mains power supplies amplifiers and computers next to or directly underneath the console Read and understand the important safety instructions printed at the start of this guide and the warnings printed on the rear of the console Check the console power supply mains voltage input is the s
Download Pdf Manuals
Related Search