BW RAS 130 User Manual - Black Widow Vehicle Security Systems
Contents
1. the keyless entry and trunk release features will still function To enter Valet Mode 1 Turn the ignition key on 2 Press and hold the valet service mode switch for 3 seconds The LED will turn on The Siren will chirp 2 times To exit Valet Mode 1 Turn the ignition key on 2 Press and hold the valet service mode switch for 3 seconds The LED will turn off The Siren will chirp 2 times EMERGENCY OVERRIDE If the transmitter becomes lost or fails to operate the system can be disarmed by using the emergency override feature To override the system 1 Enter the vehicle Because the system is armed the siren will sound 2 Turn on the ignition key 3 Press the Valet Service Mode switch for three seconds The siren will stop sounding REMOTE PANIC In the event of an emergency PANIC situation the system s siren can be triggered to attract attention To activate the Panic Feature press transmitter button 1 for 3 seconds The siren will sound The parking lights will flash The horn will honk The Panic mode will run for 45 seconds or until transmitter button 1 is pressed again Also if the vehicle is Remote Started activating the Panic Feature will shut down the Remote Start TRUNK RELEASE When the optional trunk release feature is connected pressing button 3 for 2 seconds will open the trunk 3 TRUNK DISARM FEATURE The trunk disarm feature allows the ala2. Activates the Remote Start Feature Security System Operation ARMING OPERATION To arm the system press transmitter button 1 The siren will chirp once The parking lights will flash once The doors will lock The L E D will turn solid for 2 seconds then start flashing slowly After 10 seconds the system is armed If installed While the system is armed the alarm will trigger if A door is opened The hood trunk is opened The shock sensor detects an impact to the vehicle The brake pedal is pressed When the alarm is triggered the siren will sound the parking lights will flash and the horn will honk optional If the alarm is triggered while the remote start is engaged the remote start will immediately shut down PASSIVE ARMING The passive arming feature allows the system to arm automatically without any user intervention This feature must be programmed during installation To arm the system passively 1 Turn ignition key off and open the door The LED will start flashing rapidly to indicate that the system is preparing to arm The system can be armed at any time by pressing transmitter button 1 2 Close all doors The siren will chirp 30 seconds after the last door is closed to indicate the system is now armed The doors will lock As an option the passive arming chirps can be eliminated during programming If Passive Locking is programmed during i
3. 3 Moore Street Cerritos California 90703 STATUS INDICATOR LED FUNCTIONS On Solid Valet Mode Slow Flash System Armed Rapid Flash Passive Arming Flash 2x Remote Start Flash 3x Stop and Go Mode Flash 4x Cold Start Mode PARKING LIGHTS FUNCTIONS On Solid Vehicle Remote Starting Flash 1x Doors Locked Flash 2x Doors Unlocked Flash 3x Open Zone Indication after arming Flash 4x Remote Starting Failed Flash 5x Auto Cold Start Engaged SYSTEM REFERENCE INDICATORS
4. Standard Features The System has the following standard features 2 4 button remote transmitters Status indicator LED Program Valet switch Remote Start capabilities Extended Range Receiver Multi tone siren 120dB Dual stage shock sensor Remote panic Valet mode Remote chirp mute Remote sensor bypass Passive or active arming Stop amp Go Feature Auto Cold Start Flashing parking lights Auto Rearm Passive Arming S models provided with single transmitter Optional Features This System has many optional features that may require additional parts and or labor Please contact your dealer for more details Remote keyless entry Door lock unlock Illuminated entry Hood amp trunk protection Horn honk Trunk hatch release Window roll up Back up battery Additional sensors glass breakage microwave Note Some features may not be appropriate for certain vehicles Automatic transmission and electronic fuel injection are required on vehicles for use with this system REMOTE START SECURITY SYSTEM OWNERS MANUAL 1 REMOTE TRANSMITTER FUNCTIONS Button 1 Arms the system and locks the doors Button 1 also activates the Panic feature Button 2 Disarms the system and unlocks the doors Button 3 Activates the optional Trunk Release feature Button 3 also Arms Disarms the system using the Temporary Chirp Delete feature Button 4
5. nstallation DISARMING OPERATION To disarm the system press transmitter button 2 The siren will chirp twice The parking lights will flash twice The doors will unlock The optional illuminated entry feature will turn on the dome light for 30 seconds If the alarm was triggered while away the system will respond with 3 chirps and 3 parking light flashes Button 3 Button 1 Button 4 Button 2 LED 2 AUTO REARM FEATURE The Auto Rearm feature allows the system to automatically re arm itself in the event the system is disarmed and a door is not opened within 30 seconds This feature must be programmed during installation NOTE This feature will not work on vehicles with the illuminated entry feature enabled TEMPORARY CHIRP DELETE To Arm or Disarm the system without chirps press button 3 The parking lights will flash to indicate the setting and the chirps will be muted FULL TIME CHIRP DELETE For full time silent operation the Arm Disarm chirps can be permanently disabled This feature must be programmed during installation IGNITION LOCK The ignition locking feature allows the doors to automatically lock when the ignition key is turned on and automatically unlock when the ignition key is turned off This feature must be programmed during installation VALET MODE When the system is placed into the Valet Mode both the remote starting feature and the security system will be disabled However
6. on 2 on the remote transmitter Enter vehicle turn ignition key to the on position Note Do not turn the key all the way to the start position as you may damage the starter Once the ignition key is turned on position press the brake pedal and shift the car into the proper gear and you may now drive the vehicle Note If brake pedal is pressed prior to turning on ignition engine will turn off REMOTE ENGINE SHUTDOWN If the vehicle has been remotely started and you desire to turn the vehicle off simply press and hold button 4 on the remote transmitter for three seconds After the motor has turned off the doors will relock This feature must be programmed during installation AUTO COLD START This feature allows the system to start and run the vehicle every one or two hours selectable by your installer for a period of 24 hours This allows the engine to remain at an operational temperature in extremely cold weather Auto Cold Start must be enabled during installation or it cannot be engaged Engaging the Auto Cold Start feature To turn Auto Cold Start on 1 Press and hold the brake pedal 2 While pressing the brake pedal press and hold the Valet switch and transmitter button 4 for two seconds 3 Release the brake pedal The parking lights will flash five times The siren will chirp three times The engine will start and run for thirty seconds to indicate the Cold Start feature is engaged 4 Disengaging the Au
7. rm to disarm automatically whenever transmitter button 3 is used to activate the trunk release This eliminates having to first disarm the alarm before activating the trunk release This feature must be programmed during installation CAR LOCATOR FEATURE The Car Locator feature allows the parking lights to stay on for 30 seconds instead of flashing when the alarm is disarmed This feature must be programmed during installation and is not recommended for vehicles with additional aftermarket or auxiliary lighting Remote Start Operation Important The system should be placed into the valet mode when parked inside a garage or being left for service Only start the vehicle in a well ventilated area Do not use in a closed garage or indoors Be sure to familiarize yourself with all features prior to using this product REMOTE STARTING THE VEHICLE To remote start the vehicle Press button 4 on the transmitter The siren chirps 3 times The parking lights turn on Approximately 2 seconds later the system will attempt to start the vehicle Once the car has started the heater or air conditioner will turn on and run for the pre programmed time 15 or 25 minutes If the engine fails to start on the first attempt it will repeat the starting procedure 2 more times If the vehicle fails to start after a total of 3 times the siren will chirp 4 times Driving vehicle after Remote Starting Unlock the door by pressing butt
8. to Cold Start feature The Auto Cold Start feature can be deactivated in one of three ways Press the brake pedal Turn on the ignition Remote start the vehicle using the transmitter STOP AND GO The Stop and Go feature allows the vehicle to remain running without use of the ignition key during short stops To activate the Stop and Go feature 1 Press and hold the brake pedal 2 While pressing the brake pedal push transmitter button 1 The LED will flash rapidly The parking lights will flash four times 3 Release the brake pedal 4 Remove the key from the ignition 5 Exit the vehicle and lock the doors manually or using transmitter button 1 To resume driver control 1 Unlock the doors manually or by pressing transmitter button 2 2 Turn on the ignition 3 Press the brake pedal The vehicle resumes driver control The LED will turn off If optional keyless entry feature is installed SAFETY FEATURES The System will not start the vehicle if the brake pedal is pressed or the hood is open Also if the brake is pressed or the hood is opened while remote running the remote start will shut down REPLACING LOST OR STOLEN REMOTE TRANSMITTERS This System can learn a maximum of 3 remote transmitters To add a transmitter or replace lost stolen transmitters please consult with an authorized dealer 5 6 David Levy Company Inc RSC4 Rev 1 01 01 DLC U S A 1275
Download Pdf Manuals
Related Search