Home

LUMI-studio-flash-User-Manual

1. Wireless Control Port Mounting Bracket Umbrella Input Direction Adjusting Handle SEPARATELY SOLD ACCESSORIES The product can be used in combination with the following accessories sold separately so as to achieve best photography effects FT 16 Remote Control Power Inverter Softbox Photographic Umbrella Light Stand Barndoor Snoot etc OPERATIONS e Flash Preparation 1 Take down the lamp cover Install the modeling lamp and put on the glass protection cover and standard reflector To uninstall the standard reflector press the release button on the flash head and turn the standard reflector counter clockwise to take it out as illustrated in the picture 2 Attach the flash unit on an appropriate light stand Adjust the mounting bracket 18 for a good angle and make sure it s tightened and fixed Use the direction adjusting handle 20 to adjust the flash to a desired direction Umbrella input 19 is for different photo umbrellas to put in Power Connection Use the power cord to connect the flash to an AC power source and turn on the power switch 3 The Digital Display 10 lights up indicating it s connected Modeling Lamp Modeling Lamp Button 6 controls the modeling lamp status when modeling lamp indicator lights up modeling lamp is on if not modeling lamp is off Modeling lamp sd output controller 4 is used for adjusting the power output level of modeling lamp Modeling lamp wi
2. to the product or injury to you or to others read the following safety precautions in their entirety before using this product Keep these safety instructions where users can read them for ready reference A Do not disassemble or modify There are high voltage components inside the unit Failure to observe this precaution could result in electric shock or product malfunction Should the product break open as the result of a fall or other accident send the defective back to authorized service center for inspection and maintenance Keep dry Do not handle with wet hands or immerse in or expose to water or rain Failure to observe this precaution could result in fire or electric shock Keep out of the reach of children This device contains small parts that may pose a choking hazard Consult a physician immediately if a child swallows any part of this device Do not expose to high temperature Do not leave the device in a closed vehicle in the sun or in other areas subject to extremely high temperature Failure to observe this precaution could result in fire or damage to the housing or internal parts CAUTION A A gt gt PP D After 30 continuous flashes at full power the flash should be cooled down for about 3 minutes Overheating will occur if it is used continuously without cooling down Do not keep using the modeling lamp for a long time otherwise flammable accessories attaching to flash head e g softbox will ge
3. NANO LUM Compact Studio Flash Instruction Manual FOREWORD Thanks for choosing LUMI series studio flash It is a durable and good quality strobe with complete functions to help photographers create desired lighting effects The product is suited for wedding portrait and product photography The LUMI flash offers e Precise output control 30 steps from 5 0 8 0 in 0 1 increments e High qualified modeling lamp 150W output steplessly adjustable e High output stability a tolerance of not larger than 2 under the same output e Anti preflash function enabling synchronization with cameras having a one preflash firing system e Auto power discharge when the flash output is adjusted from high to low e Adjusted settings intelligently remembered after 3s and automatically recovered after a restart e Wireless control of the flash power ratio the on or off of modeling lamp and buzzer as well as flash triggering CONTENTS 01 01 02 02 03 03 03 04 04 04 04 04 05 05 05 05 05 06 06 06 07 07 Foreword For Your Safety Caution Names of Parts Body Accessories Separately Sold Accessories Operations e Flash Preparation Power Connection e Modeling Lamp e Power Output Control Test Button e Sync Triggering e Slave Trigger Model e Buzz Function e Memory Function Wireless Control Function Tube Replacement Technical Data Maintenance FOR YOUR SAFETY To prevent damage
4. el the flash can function as an auxiliary lamp offering various effects of light and shadow 3 Anti preflash model The slave triggering indicator 13 glows red indicating the flash will receive two external flashes within 2 seconds and will fire synchronously when receiving the second flash In this model the flash can function as an auxiliary lamp applicable to TTL system With this anti preflash function synchronization is supported with cameras having a one preflash firing system Buzz Function The sound button 7 is used to decide whether there is sound reminder for ready flash after recharging When the buzz indicator 12 is on it means buzz function is working if it is off the buzz function is shut down A BI sound will be heard when Get it s fully charged Memory Function The device is equipped with memory function for the panel setting It will help remember the panel setting 3 seconds after you set it When starting up the flash next time the panel setting will be the same as that before powering it off Wireless Control Function The flash unit is built in with a Wireless Control Port 17 so that you can wirelessly control the on and off of your flash modeling lamp and buzzer as well as adjust the flash output level etc To control the flash wirelessly you need a PIXAPRO series remote control set on camera and on flash Insert its receive end into the Wireless Control Port 17 on the flash and in
5. ll be off automatically after lighting for 2 hours avoiding overheat due to long time lighting when the user is not nearby modeling lamp on for a long time It is recommended to cool it down for one minute after 10 minutes working When there is flammable accessory on the flash unit do not keep the Power Output Control Flash output controller 5 decides different power output satisfying the light requirements in different environment The power is adjustable freely from 5 0 to 8 0 which will be accordingly told on the digital display 10 OF on the display indicates that the flash triggering function is turned off It can automatically discharge power when the flash output is adjusted from high to low Test Button To fire the flash without taking a picture press the test button 9 It can also help adjust the flash brightness when combined with the flash output controller 5 Sync Triggering The sync cord jack 2 is a 3 50mm plug Insert a trigger plug here and the flash will be fired synchronously with the camera shutter Slave Trigger Model Three slave triggering models are available and can be set by pressing Slave Model Button 8 1 No optical control The slave triggering indicator 13 is off indicating the slave triggering function is shut down 2 One fire model The slave triggering indicator 13 glows blue indicating the flash will fire synchronously when receiving one external flash In this mod
6. lly and find out the reason Avoid sudden impacts and the lamp should be dedusted regularly It is normal for the lamp to be warm when in use Avoid continuous flashes if unnecessary e Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories The flash tube and the modeling lamp are user replaceable Replacement tubes and lamps can be obtained from the manufacturer e This product except consumables e g flash tube and modeling lamp is supported with a one year warranty e Unauthorized service will void the warranty If product fails or comes into contact with any liquids do not use it until it is repaired by professionals Disconnect the power when cleaning the flash or when changing the flashtube modeling lamp e Changes made to the specifications or designs may not be reflected in this manual sia
7. sert the transmit end into the camera hot shoe Settings made on the hotshoe mounted transmit and receive ends will be wirelessly communicated to the flash Then you can press the camera shutter release button to trigger the flash For full instructions on the use of FT series remote control see its user manual Tube Replacement Shut down the power and remove the power cord before replacing the flash tube and wear insulated gloves Then loosen the iron wire on the tube keep a balanced hold on the two feet of the flash tube and pull out the old tube gently Take down the feet casing from the old tube and put it on the new one Hold two feet of the new tube and target directly towards the two copper outlets then push them slightly in Twine the iron wire on the stainless steel sheet to fix the flash tube 06 TECHNICAL DATA Model LUMI200 LUMI300 LUMI400 Max Power WS 200WS 300WS 400WS Guide Number m ISO 100 49 58 65 Color Temperature 5600 200K Operating Voltage AC200 240V 50Hz Power Output Control OFF 5 0 8 0 1 32 1 1 Modeling Lamp W 150W Recycle Time 095125 03 55 Triggering Method Sync cord Test button Slave triggering Wireless control port Flash Duration 1 2000 1 800s Fuse 8A Dimension Flash diameter 12 5CM height of flash with handle 25CM length of flash with lamp cover 35CM Net Weight Approx 1 8KG Approx 1 9KG Approx 2KG MAINTENANCE e Shut down the device immediately when it works abnorma
8. t burnt A 10 minute time is recommended in this case After 10 minutes cool it down for 1 minute When using a snoot do not keep the modeling lamp on for a long time or fire too frequently not over six times for one minute Overheating will result in damages for strobe housing and or studio light Do not touch the lamp cap when the flash or modeling lamp is working as it will give out heat leading to high surface temperature Do not touch the two terminals of the tube outlet as there is high voltage inside Wear insolated gloves before replacing the tube or modeling lamp Avoid sudden impacts as this can damage the flash tube and or modeling lamp Do not flash directly towards naked eyes especially those of babies otherwise it may lead to visual impairment Disconnect from the power supply when it will not be used for an extended period 02 NAMES OF PARTS Body 1 AC Power Socket 11 2 Sync Cord Jack 12 3 Power Switch 13 4 Modeling Lamp Output Controller 14 5 Flash Output Controller 15 6 Modeling Lamp Button 16 7 Sound Button 17 8 Slave Model Button 18 9 Test Button 19 10 Digital Display 20 e Accessories 1 Sync Cord 2 Power Cord 3 Lamp Cover 4 Glass Protection Cover 5 Modeling Lamp 6 Instruction Manual Modeling Lamp Indicator Buzz Indicator 15 10 13 05 14 08 03 16 20 Slave Triggering Indicator Test Indicator Lamp Light Sensor Fuse

LUMI-studio-flash-User-Manual

Contents

Download Pdf Manuals

Related Search

Related Contents