Руководство пользователя для считывателя магнитных
Contents
1. The finger print sensor software creates a fingerprint template which is a highly compressed and digitally encoded mathematical representation of fingerprint features This template is created when a user registers a finger and is stored in an encrypted file When the user later touches the fingerprint reader to authenticate a new template is created and compared to the registered template If there is a match the authentication is successful c Finger Print Recognition In order for the sensor to acquire a good image of your finger you must place the pad of your finger but not the tip in the center of the sensor window and apply gentle even pressure Do not roll your finger as usually practiced in the traditional ink and paper fingerprint taking technique Pressing too hard will distort your fingerprint Pressing too lightly will not expose a large enough area of your finger Also make sure to hold your finger on the sensor until you see the sensor light blink this may take longer for dry fingers Then lift your finger Although you may use any finger with the sensor your index finger of either hand works best If the sensor is capturing your finger image as indicated by the sensor blink and you have tried all the above suggestions you may need to reregister your finger d Sensor Activation The LED behaviors are described in the following table LED Color Description Blue Finger print sensor on standby Red Reading su2. BPI 210 BPI Recording capacity 79 7 40 5 107 5 72 7 Card data specs is decided by reading head type and must be specified upon ordering 3 Other Specifications Standards AAMVA CA DMV Interface USB Rated Voltage 5V DC Rated Current 300 mA Max Reading Head Single ISO head or Dual ISO Head or JISII head Reading head type must be specified upon ordering POSIFLEX gst 131454 REPRAN E Ze fh ea TER ae
3. POSIFLEX SD 460 466 Z W SERIES UPGRADE KIT USER S MANUAL Rev A0 I Features ISO 7811 Magnetic Stripe Reader with USB interface Dual directional operation for MSR 3 tracks type MSR reads AAMVA and CA DMV card Textured front surface Built in Optical Finger Print Sensor Side mounted on KS 62 68 69 72 75 77 series SD 460Z 466Z or KS 66 73 series SD 460W 466W FCC NOTICE This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference WARRANTY LIMITS Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application The hardware utility program including instr
4. ccessfully Failure to connect to a self powered USB port will cause non operation of the sensor If you activate your terminal s power saving functionality but your third party application does not support this then your fingerprint sensor will enter sleep mode even though your workstation does not If this occurs you will need to reboot the system Please check with your application developer for compatibility e Cleaning the Sensor Depending on the amount of use the sensor window may need to be cleaned periodically To clean it apply the sticky side of a piece of adhesive cellophane tape on the window and peel it away as in the drawing at right Under heavy usage the window coating on some sensors may turn cloudy from the salt in perspiration In this case gently wipe the window with a cloth not paper dampened with a mild ammonia based glass cleaner IV SPECIFICATIONS 1 Reader Specifications Applicable card type ISO 7811 JIS X 6302 Card feed method Manual Manual Card feed direction Bi direction Bi direction Read write function Read only Read only Card feed speed 5 to 55 inches sec 100 to 1200mm sec Error rate lt 0 5 lt 0 1 Reader specs option must be specified upon ordering 2 Card Data Specifications Data standard IATA ABA THRIFT JISH Track used Track 1 Track 2 Track 3 Rear section Recording method FF FM FF FM FF FM FF FM Recording density 210 BPI 75 BPI 210
5. stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without the prior written consent of Posiflex Technology Inc the publisher of this documentation TRADE MARKS AND SERVICE MARKS C POSIFLEX is a registered trademark of Posiflex Technology Inc an ISO 9001 and ISO 14001 certified manufacturer Other brand and product names are trademarks and registered trademarks and service marks of their respective owners P N 19800902020 ll Installation 1 Hardware Installation 1 Release the 2 screws on the back of the right side of the terminal to remove the protective cover Store the protective for future use 2 Connect the cable found under the cover with the white connector inside SD 460 466 Z W 3 Attach SD 460 466 Z W to the terminal with the corresponding screw holes in alignment and then secure the 2 screws 2 Driver Installation 1 MSR The magnetic stripe reader connects to the host through USB port working as a USB KB and also requires no driver installation except setting up the USB keyboard to be enabled in system CMOS setup if the OS does not do it automatically Refer to Operation Guide for manipulation over the reader configuration 2 Finger Print Sensor To include the drivers for this sensor to perform finger print registration or verification authentication in an AP requires the software programmer to purchase and utilize its SDK soft
6. uctions for its use is provided AS IS without warranty of any kind Posiflex Technology Inc further disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose the entire risk arising out of the use or performance of the software and documentation remains with you ABOUT THIS MANUAL This manual is written in an attempt with full strength to assist the user to utilize the upgrade kit SD 460 466 Z W for the Posiflex fan free touch terminals KS series This series of products incorporate 2 delicately designed POS peripherals each can be used as an excellent tool to accommodate the required security specially involved in POS business kiosk and hospitality operation This manual covers the conceptual and operational aspects of these units For technical aspects involving opening of the unit or option implementation it is only available to the authorized distributors The manufacturer of the SD 460 466 Z W series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology The user may always obtain the most up to date information through any of our web sites http www posiflex com or http www posiflex com tw Copyright Posiflex Technology Inc 2013 All rights are strictly reserved No part of this documentation may be reproduced
7. ware developer s kit However Posiflex delivers this optical finger print sensor with its drivers Please find in the mini CD delivered with SD 460 466 Z W series except SD 460 466 Z W model or Product Information CD delivered with Posiflex POS system the folder for Posiflex Optical Finger Print Sensor lll Operation Guide 1 Magnetic Stripe Reader The MSR in SD 460 466 Z W series reads an ISO magnetic stripe card without driver Yet there is a MSR EXE program for SD 460 466 Z W model and a Posiflex USB MSR Manager program for other model provided to control some parameter configuration for this MSR Through this program you can enable disable track set up AlttNum approach for ASCII codes and enable disable Leading Stop code Please look for USBMSR and SetUp folders in the mini CD delivered with SD 460 466 Z W or Product Information CD delivered with Posiflex POS system to install the program or download it from our web site http www posiflex com or http www posiflex com tw Page 1 Finger Print Sensor 2 a Cautions 1 Never pour the glass cleaner directly on the sensor window 2 Never use alcohol based cleaners 3 Never submerge the sensor in liquid 4 Never rub the window with an abrasive material including paper 5 Do not poke the window coating with your fingernail or any hard item such as a pen b Principle The finger print sensor software never stores fingerprint images
Download Pdf Manuals
Related Search