Home

Manual

1. When installing the camera check the reception of the receiver before final installation Have someone hold the camera in the area to be monitored and another person to check the reception with your TV or monitor If interference or other problems occur refer to the Troubleshooting Guide Technical Data Camera Receiver 7 5 V DC plug in power unit 5 V DC plug in power unit Battery operation 2 x AA Battery operation 4 x AAA Alkaline Alkaline Operating voltage Current consumption 200 mA _ 600 mA Transmitting frequency esc 3 2 4 Ghz Modulation iR 3 Light sensitivity Video output level Audio output level mono Audio Video Connection jacks Picture sensor 1 Vp p 75 Ohm 330 TV lines horizontal 480x234 Picture Range 100 m 300 ft Line of sight 14 to 122 F 10 C to 50 C Mass approx without tripod 1577 50g Dimensions without 75 x 33 x 122 mm 75 x 33 x 130 mm Aerial LxWxH LxWxH Plug in power units Operating voltage 110 240V 60 or 50Hz 110 240V 60 or 50Hz Output voltage 7 5V DC 500mA 5V DC 1000mA Maintenance The devices are maintenance free so never open them The guarantee becomes void when you open the appliance Only clean the outside of the devices with a soft dry cloth or a brush Prior to cleaning remove the devices from all voltage sources Do not use any carboxylic cleaning agents or pe
2. Navigator User s Manual Model No CCD 420 WIRELESS 2 5 COLOR TFT LCD MONITORING SYSTEM Portable 2 5 Color TFT LCD with Receiver Wireless Color Camera This manual contains important information about this product s operation If you are installing this product for use by others you must leave this PLEASE READ CAREFULLY AND SAVE manual or a copy with the end user a E Night Vision _ Battery lguitaaws De Koror Installing the Camera ATTENTION Prior to drilling and inserting the screws make sure that there are no electric cables pipes etc in the wall that may become damaged SY 11 1 Antenna 7 IRLED 2 Low battery indicator 8 Camera ON OFF switch 3 Power indicator camera Kit baby monitor 4 Eye ball camera lens 9 Channel switch 5 Power ON OFF switch 10 DC Power 6 Microphone 11 Power adaptor plug with low voltage switch Installing and Connecting the Devices Select a suitable installation site from which you want to monitor the desired object A suitable installation site has the following features dry as dust free as possible little vibrations good air circulation with a wall outlet in close vicinity 03 Select an installation site that is not Screened off by reinforced concrete walls mirrors metal shelves etc Close to the sender respectively receiver there should not be any appliances with strong elect
3. ric fields e g cell phones walkie talkies electric engines etc The above points could severely impair radio transmission respectively reduce the range Fastening the wall bracket Look for a suitable place for mounting with a socket close by Screw the wall bracket with the supplied screws to a suitable wall mount slot wail or a suitable platform use Se dowels if relevant li ed Align the camera and screw the attach stand to corrugated plastic sleeve tight mounting surface 3 battery compartment a a Wea Connecting the camera Connect the small voltage plug of the power unit to the voltage supply jack of the camera Pay attention to the correct output voltage of 7 5V DC i Insert the plug in power unit into a suitable main socket The camera is now ready for use Installing the Receiver the monitor approx 1 m above ground better receiving Conditions There must be one Power outlet in proximity to the receiving site ATTENTION Only place the monitor on fugged and stable surfaces Sensitive surfaces or surfaces that dissolve softeners may become damaged Use a suitable underlay 1 VOL Control 6 DC Power 2 Brightness Control 7 Antenna 3 CH Select 8 Channel LED 4 AN Output 9 Power LED 5 LCD Power ON OFF 10 BAT LOW LED POWER ON 11 Power adaptor plug with low voltage switch ae pai eas 12 AN Cable Connecting the receiver ee Connect the AV cable as depicted to a S
4. trol alcohol or similar These attack the surfaces of the devices Besides the vapors are hazardous to your health and explosive Do not use any sharp edged tools screw drivers metal brushes or similar for cleaning a
5. ug the adapter into a standard 1 10V 240V AC outlet 3 You can use either AC DC adapter for long time use or 2 AA battery for mobile use The life time of 2 AA battery operation is 1 5hr w o IR function and thr w IR function System Setup 1 Select the channel Channel 1 3 to be used on both the camera and receiver NOTE Make sure the camera and receiver are set to the same channel 1 2 3 and Camera should be turn on CH 2 Set the selected channel by gently pushing the dip switch n for same channel on both the camera and the receiver For example to set both the camera and receiveron Channel 1 Push the Channel 1 dip switch located on Camera Set to Receiver Set to the side of the camera and the receiver to be in same Channel 1 Channel 1 channel 3 For baby monitoring feature please select the camera ON OFF switch to be OFF on the transmitter unit but make sure the camera and receiver are set to the same channel If more than one camera is to be installed and operated at the same time For example to operate two cameras set Camera 1 to Channel 1 set Camera 2 to Channel 2 a and on the receiver set channels 1 or 2 to ON For more than one camera operation one image CH1 or CH2 is showed at a time without auto scanning feature See Camera and Receiver Setting Chart below for detail O O poker BAT LOW Camera Set to i Receiver Set to Channel 1 Channel 2 Additional Notice
6. uitable 00 monitor or TV system with an AV cinch 2 input and the receiver white red plug audio 1 SSS tone in mono yellow plug video y Connect the smail voltage plug of the power unit to the voltage supply jack of the receiver Pay attention to the correct output voltage of 5V DC Insert the plug in power unit into a suitable main socket The receiver is now ready for use System Installation When installing the camera check the reception of the monitor before final installation Have someone hold the camera in the area to be monitored Have another person move the monitor to a variety of locations throughout the house to check reception If interference or other problems occur refer to the Troubleshooting Guide Wireless 2 5 Color TFT LCD Monitoring Sysetem To install the system follow these steps Monitor 1 Plug the 5V AC DC adapter cord into the DC Input Jack on the side of the monitor 2 Plug the adapter into a standard 110V 240V AC outlet Press the power button to turn on the monitor 3 A V outputs on the LCD monitor can be connected to the A V input on a TV set for a large screen display or to the A V inputs on a VCR for recording 4 You can use either AC DC adapter for long time use or 4 AAA battery for mobile use The life time of 4 AAA battery operation is 45 minutes Camera 1 Plug the 7 5V AC DC adapter cord into the DC input jack on the back of the camera 2 Pl

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents