ML610Q102 Reference Board User`s Manual
Contents
1. L A P G FEBL610Q102 03 SEMICONDUCTOR ML610Q102 Reference Board User s Manual Issue Date Feb 20 2013 ML610Q102 Reference Board User s Manual NOTES No copying or reproduction of this document in part or in whole is permitted without the consent of LAPIS Semiconductor Co Ltd The content specified herein is subject to change for improvement without notice The content specified herein is for the purpose of introducing LAPIS Semiconductor s products hereinafter Products If you wish to use any such Product please be sure to refer to the specifications which can be obtained from LAPIS Semiconductor upon request Examples of application circuits circuit constants and any other information contained herein illustrate the standard usage and operations of the Products The peripheral conditions must be taken into account when designing circuits for mass production Great care was taken in ensuring the accuracy of the information specified in this document However should you incur any damage arising from any inaccuracy or misprint of such information LAPIS Semiconductor shall bear no responsibility for such damage The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products LAPIS Semiconductor does not grant you explicitly or implicitly any license to use or exercise intellectual property or other rights held by LAPIS Semiconductor and ot2. ach hardware parts Embedded microcontroller U1 ML610Q102 Embedded parts J1 Jumper for RESET_N switch 3pin pin header and short pin J2 Jumper for VDD switch 3pin pin header and short pin CNU1 2 Connector for Peripheral CNUE Connector for on chip debug emulator 14pin connector C1 C3 Capacitors for power supply Operating voltage Board size 2 7V to 5 5V 30 00 x 40 00 mm 3 Parts layout lt fig 1 Parts layout gt ML610Q102 Reference Board User s Manual 4 Notes on use 1 The information contained herein can change without notice owing to product and or technical improvements Before using the product please make sure that the information being referred to is up to date 2 Before using this board read carefully and understand the contents of the ML610Q102 user s manual and the uEASE user s manual 3 The engineering sample of ML610Q102 is mounted on the board Therefore please confirm the characteristic finally by using MP of ML610Q102 and customer s mass production boards 4 When you use uEASE please set J1 jumper to the uE side 5 When a power supply is given from the exterior please be given by pin4 of CNU2 connector and set J2 jumper to the USR side 6 When you set J2 jumper to the USR side and uEASE is connected please turn ON the power supply of a board before starting UEASE Moreover please stop UEASE before turning o
3. device LAPIS Semiconductor shall bear no responsibility in any way for use of any of the Products for the above special purposes If a Product is intended to be used for any such special purpose please contact a ROHM sales representative before purchasing If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law you will be required to obtain a license or permit under the Law Copyright 2013 LAPIS Semiconductor Co Ltd ML610Q102 Reference Board User s Manual ML610Q102 Reference board is prepared by LAPIS SEMICONDUCTOR to have you study the operations of ML610Q102 The board is only minimum necessary components are mounted on the board by LAPIS SEMICONDUCTOR for brief use of ML610Q102 By using the board with UEASE on chip debug emulator hereinafter referred to UEASE and free sample U8 Development Tools CD ROM which is bundled in the package of uEASE not only Software development debugging but also writing Flash ROM in the devices are capable This board also works in stand alone mode with external power suppy without UEASE Before starting works with this board read below carefully and understand notices 1 The board features Supports flash ROM programming and on chip debugging using RESET_N and TEST pins 2 The board hardware specifications Please refer to the reference schematics for detail on connections of e
4. ff the power supply of a board 7 When J2 jumper is set to the UE side the power supply capacity of UEASE is 3 3V 100mA 8 This board has a conductivity pattern in the back therefore it may short circuits when it is used having put on the existing conductive component 5 Reference schematic The reference schematic of this reference board is shown below 2 4 6 8 10 12 RESET_N TEST PBO PB1 PB2 PB3 PA2 VPP lt fig 2 Reference schematic gt ML610Q102 Reference Board User s Manual 6 Reference dimensions The reference dimentions of this reference board is shown below Y mm 1pin X Y 10 16 35 56 X mm 40 64mm 30 48mm Origin 1pin X Y 10 16 2 54 lt fig 3 Reference dimensions gt
5. her parties LAPIS Semiconductor shall bear no responsibility whatsoever for any dispute arising from the use of such technical information The Products specified in this document are intended to be used with general use electronic equipment or devices such as audio visual equipment office automation equipment communication devices electronic appliances and amusement devices The Products specified in this document are not designed to be radiation tolerant While LAPIS Semiconductor always makes efforts to enhance the quality and reliability of its Products a Product may fail or malfunction for a variety of reasons Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury fire or any other damage caused in the event of the failure of any Product such as derating redundancy fire control and fail safe designs LAPIS Semiconductor shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual The Products are not designed or manufactured to be used with any equipment device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury such as a medical instrument transportation equipment aerospace machinery nuclear reactor controller fuel controller or other safety
Download Pdf Manuals
Related Search