installation and user`s guide – das m44ci
Contents
1. lt Look into the Future gt DAS M44CI Diversity Autoscan System INSTALLATION AND USER S GUIDE DSi cee INSTALLATION AND USER S GUIDE DAS M44Cl Warnings Important Safety Instructions and Caution Please read all of these instructions regarding your unit and retain them for future reference 1 2 3 4 5 6 7 8 9 Read this manual fully and carefully before operating DAS digital receiver Keep this manual handy as a reference for operating procedure and safety information Pay close attention to all warnings and follow the instructions carefully Do not allow other people to use the system until they have read and understood the operating instructions Do not push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electronic shock Don t use or perform any function while driving This could cause accident endangering both your safety and the safety of others always observe safe driving rules and follow traffic regulations If prolonged intervention on the unit is necessary stop the vehicle in a safe place and make adjustments Video output For your safety ensure that the DRIVER monitor is connected to the video OUT DRIVER If the connection to the handbrake and the menu settings have been done properly the Video DRIVER will only work with the handbrake on and therefore only with the vehicle2. described below 1 Turn the remote control face down 2 Press down on the ridged area of the battery cover and slide it off 3 Slide another battery in mod CR2025 o CR2032 Multiconn Srl Pag 8 of 23 DAS M44Cl User Manual EN Start and Antennas installation Connect the 4 antennas to receiver but DO NOT fix them yet at windows use first function MENU 1 2 3 at page 11 to find right location We recommend to use a very good quality antennas because they can grant a better reception of the Signal TV suitable to DAS receiver poor or medium quality antennas can strongly affect the reception of the signal and therefore the performance of the unit DAS is a receiver with 4 antennas 3 assigned to the reception of the TV channels and 1 assigned to the autoscan and to the update in real time of the dynamic TV list e Antennal RDS autoscan and update of the TV list e Antennas 2 3 4 reception of the TV channels e Antennas 1 2 3 4 with stand by scan function the TV list is updated with all 4 antennas Inizializzazione in corso Multiconn Srl Pag 9 of 23 DAS M44Cl User Manual EN I 1 votonc ii e Selecta TV channel using arrow UP and arrow down with a good reception and push button OK Menu The TV channel will be showed on the screen Jinn ISst Once the TV channel is well visible push MENU 1 2 3 this function is essential to install the 4 antennas inside the vehicl
3. please contact the dealer where you bought the unit for assistance Multiconn Srl Pag 23 of 23 DAS M44Cl User Manual EN
4. still Viewing images while driving is forbidden and dangerous See pag 5 for handbrake setting Check for correct power supply Don t disassemble tamper with or attempt to repair any part of the product Any such actions will immediately void the warranty and may lead to damage accidents or injury High temperature and humidity may compromise operations Do not expose the unit to rain and moisture If any solid object or liquid fall into the cabinet unplug the unit and have it checked by qualified personnel before operating it any further The unit must be installed by experienced personnel only Wrong wiring may cause problems to the vehicle as well as damage accidents and injury Do not attempt to install or service your DVB T receiver by yourself Do not install the unit where it may 1 Obstruct the driver s attention 2 Impair the performance of any of the vehicle s operating systems or safety features including airbags hazard lamp buttons etc 3 Impair the driver s ability to safely operate the vehicle Before wiring disconnect the cable from the negative battery terminal Don t use bolts or nuts in the brake or steering systems to make ground connections 10 Arrange the wiring so itis not crimped or pinched by a sharp metal edge 11 Connect and use only very good quality antennas Multiconn Srl Pag 2 of 23 DAS M44Cl User Manual EN WHAT IS DAS DAS system analyzes and scans automatically the TV channels fr
5. 4 Video Outdrive yellow RCA Multiconn Srl gt external device i e DVD gt Camera IN gt radio HU or monitor gt front Video Output Pag 6 of 23 DAS M44CIl User Manual EN IR Remote Control M44Cl with RCA fixed M44Cl without RCA e INPUT IR gt Optional integration Head Unit command M44Cl with RCA fixed M44Cl without RCA Multiconn Srl Pag 7 of 23 DAS M44Cl User Manual EN Remote Control Operations e Power button Button to switch ON and OFF the receiver e Arrow and Buttons used to move onto the right and left directions inside the menu and the 2 different TV list Buttons used for zapping e Arrow and Buttons used to enter inside the TV list and inside Memo TV Channels List Buttons used to browse up and down inside the 2 TV list and inside the different menus OK MENU button Button used to select and confirm a choice or to enter inside the configuration menu setting e Numerical buttons Buttons used to memorized and change the TV channel e TV AV button It allows to select an external AV output i e DVD e Button Volume up and down e TX button The buttons is used to select subtitles function where available e DAS button Radio e Pay TV functions Remote Control Battery Installation Before attempting to operate your remote control check battery and in case install a new as
6. Is activated 2 The Memo TV Channel List is controlled directly by antennas no 2 3 4 It allows to store the TV channel in the desired position and it gt strictly connected to the auto scan made by antenna no 1 ore Aveleno Lk h Focus e Push or to enter inside the 2 lists Push or and select what kind of list is interested in e Push or to browse the TV channels available inside the list e Push OK Menu Y to watch the selected TV channel Multiconn Srl Pag 14 of 23 DAS M44Cl User Manual EN Memorize TV Channel DAS system is the real heart of auto scan technology the searching of the TV channels and the related frequencies is made automatically and no manual intervention is needed The storage memorization of the TV channels is essential to ensure the best performance of the receiver e Push button or and enter inside the TV lists Inside the menu there are 2 pages containing the TV List and the Memo TV Channel List push button or to change the page and select the related TV list The 2 TV lists have 2 different colours to avoid misunderstandings e Select TV list e Browse or to reach the desired TV channel e Push button OK Menu to confirm fave oo LIST le TTT 1 i o T i Now the selected TV channel is showed on the screen e To memorize keep push at least 2 seconds a numerical button for ex button no 5 the TV channel will be m
7. MPEG4 does not support Dolby Digital audio AC3 Change the screen or take another DAS tuner Tolerances of electronic components between DAS product and the screen The yellow wire must have always the 12V check the status of the power Connect the green wire and check the polarity refer to manual at pag o DAS M44Cl User Manual EN PROBLEM POSSIBLE REASON SOLUTION There are 2 grey bars The 2 bars of stored channels have Deactivate the 2 bars from menu on the 2 edges on the been activated from configuration screen menu int Please memorize the preferred Error appears on the Possible impact crash suffered by After having switched off Deactivate the function on the car the LED of The stand by scan system is active cOnfguration menu antennas keep on Refer to manual at pag 12 The channel has not been Deactivate the function from the memorized in the MEMO TV channel configuration menu list It advise users to do it Refer to manual at pag 12 Memo signal while watching a channel from TV list Refer to manual at pag 12 The receiver without CI option The receiver is not Cl version does not support pay TV channel vision The CAM module and CARD has not jncert the cam and card be inserted The unit does not show Replace the card with another one Take out CAM card and insert Incorrect configuration of the CAM them after having selected a pay TV channel from TV list If problem persists
8. e 3 Multiconn Srl Pag 17 of 23 DAS M44Cl User Manual EN Upgrade via USB SW upgrades are periodically released It is recommended after installation to check the SW loaded on the receiver if itis updated to the latest release To verify log on http www dasdvbt com software php e Check the SW on the receiver using the function menu 123 e On Top itshows DAS rev 0 xxx e Check if the revision number Is the same as that one shown online DAS HD rov 0 250 NuliConn FE 216 Anti Ant 2 Ant3 Ant4 Oli limelmiih i t lae Melel a grip on the situation e fitis not the same download the latest SW present in a compressed mode and copy on a USB stick FAT32 formatted after decompressed Note only the file decompressed can be used e Insert the USB key into its connector with receiver OFF e Turn ON the receiver a confirmation request to load the new software will be shown on screen e Confirm Upgrade and wait its conclusion PORIIN E ORTA sul dispositivi nere MCNU per LEGEL in aiti ERI jer USCITi Itis MANDATORY NOT to turn off the receiver and or NOT to remove the USB key until the update is completed otherwise the piece will be damaged Multiconn Srl Pag 18 of 23 DAS M44Cl User Manual EN PAY TV At first activation for the proper and correct operation plug the Cam and the respective card when a pay channel has already been selected from the TV List Focus fiw LIST FOCU S
9. e because it guides to find the best place where fix the antennas to get a better reception of the signal e We recommend to install the 4 antennas in the 4 sides of the vehicle horizontal or vertical avoiding metal edges and avoiding shielded windows After pressing MENU 1 2 3 On the screen 4 bars appear 1 for each antenna The movement of the bar highlights the power of the signal with the related reception major is the DAS HD rev0 25 MultiGConn FE 216 level of the bar better is the place of the signal reception where positioning the antennas Ant Ant2 e Install each antenna taking care of the level Signal of the bar Anta To exit from antenna menu push OK Menu Multiconn Srl Pag 10 of 23 DAS M44Cl User Manual EN Settings Configuration Menu Inside this menu there are the settings of receiver and some functions useful for end user e Push OK Menu button In the next screenshot all functions and features of the product will be showed Menu di configurazione Lingui f italano UP sa 4 ENTER y Use arrows and to browse up and down Use arrows and to move on the left and the right side and enter inside the sub menus Menu di configurazione Lingu it liano Itallano UP M gt ENTER y To exit from configuration menu push OK Menu button or e Languages Select the language e Screen Select the screen in 4 3 or 16 9 e Video output Select if the vid
10. emorized automatically at position no 5 Multiconn Srl Pag 15 of 23 DAS M44Cl User Manual EN The TV channel will be included inside the Memo TV channel list at position no 5 e fthe TV channel bars has been selected the TV channel appears also at position no 5 of the TV channel bar showed on the screen e Repeat this procedure to store all the other TV channels Multiconn Srl Pag 16 of 23 DAS M44Cl User Manual EN Change TV Channel To change the channel just digita key number of a stored channel for example by pressing 31 the channel stored at position 31 of the MEMO TV channel list is selected and displayed on screen If you want to instead display a TV channel that is not memorized you must enter the TV List and select the desired TV channel f ivon LISTI Focus NA i After 40 seconds of continuous viewing a flash appears on the screen This flash warnings the user that the channel has not been stored 4 seconds after this warning disappears from the screen After 1 minute there is a second reminder combined with an audible warning that alerts the user to save the current channel After 4 seconds this alert will disappear from the screen This notice can be disabled from the configuration menu Zapping While viewing a TV channel to have a quick zapping simply press or to display the next or previous channel to the current channel you are watching Rai Sport 2 wml tt
11. eo Is in PAL or NTSC Multiconn Srl Pag 11 of 23 DAS M44Cl User Manual EN e Info time duration Selecting the duration time It s possible to choose the time of the screenshots or messages showed on the monitor e Stand by Scan This is an essential feature to update automatically the TV list Selecting this option when the vehicle is turned off or when the receiver is in stand by DAS is ON and it will use the 4 antennas in autoscan version to scan the frequencies and automatically update all TV channels inside the TV list In this case the TV list is always updated For this function DAS unit has a consumption power is 500mA and it will take about 10 minutes When Autoscan is completed the unit will switch OFF automatically Select NO to disable this function e Memo signal To perform at its best DAS needs to have the TV channels memorized Each time a non memorized channel is showed on the screen DAS reminds the end user with a Signal to memorize the TV channel Select NO to disable this function e TV channel bars This feature allows to end user to understand in real time if a TV channel is available at that time inside the TV list provided that this channel has been previously memorized This function works with memorized TV channels The 2 superimposed TV channels bars 1 on the upper side of the screen the other one on the bottom Side also display the 10 memorized TV channels while watching a TV program End
12. equencies by eliminating the manual procedures normally used DAS allows to get the best reception of the signal during a journey Using the RDS system combined to digital signal DVB T DAS changes automatically the frequency of the TV channel avoiding the waiting to receive the new signal Contents e Installation pag 5 e Remote Control Operations pag 8 e Start and Antennas Installation pag 9 e Settings Configuration Menu pag 11 e Antennas status and check pag 13 e TV Listand Memo TV Channels List pag 14 e Memorize TV channels pag 15 e Change TV channels pag 1 e Zapping pag 1 e Upgrade via USB pag 18 e Pay TV pag l9 e Trouble Shooting Q amp A pag 20 Multiconn Srl Pag 3 of 23 DAS M44Cl User Manual EN wg Se With fixed RCA Aa Without RCA Multiconn Srl Pag 4 of 23 DAS M44Cl User Manual EN Installation Install DAS DVB T receiver with ALL 4 antennas Connect the 4 antennas to the receiver before switching the unit on but pay attention NOT TO FIX immediately the antennas on windows or any other inside part provided it s not metal until you have found the proper location as shielded glasses can strongly influence reception To find best suitable mounting position use the function on remote control MENU 1 2 3 as shown at page 11 Only when a suitable position is found carefully fix the 4 antennas and route the antennas cables accordingly It would probably need to try some mou
13. nting positions to determine which one provides the strongest signal in your vehicle Connections Power M44Cl with RCA fixed M44Cl without RCA ms m I Yellow gt Battery 12V 24V Red gt Acc ignition Orange gt Parking Brake Black gt Ground Green gt Reverse Gear Blue gt Out 12 24V only for M44CI with RCA fixed Reverse Gear The device can be used with a reverse video camera not included To see the video camera image shown on DRIVER monitor the GREEN wire or the power cable must be connected to a 12V signal activated by reverse gear Handbrake For safety reason the DRIVER s monitor will not work while vehicle is moving It s mandatory to connect the ORANGE wire of the power cable to a 12V signal activated by handbrake Multiconn Srl Pag 5 of 23 DAS M44Cl User Manual EN Panel IN OUT M44Cl In Out Panel with RCA 1 Audio OutR redRCA Audio OutL white RCA Video Out drive yellow RCA 2 Video Out1 yellow RCA 3 Aux 2 Video yellow RCA 4 Aux 1 Audio R red RCA Aux 1 Audio L white RCA Aux 1 Video yellow RCA gt radio HU or monitor gt front Video Output gt Camera IN gt external device i e DVD M44Cl In Out Panel without RCA fixed 1 Aux 1 Audio R red RCA Aux 1 Audio L white RCA Aux 1 Video yellow RCA 2 Aux2 Video yellow RCA 3 Audio OutR yellow RCA Audio OutL white RCA Video Out1l yellow RCA
14. nual at pag 15 DAS M44Cl User Manual EN PROBLEM POSSIBLE REASON SOLUTION The signal quality of some channels TV is too low All channels show no Signal or random mosaic tiles appear on display Antennas are not properly connected No DVB T service is provided in that area The area is not digitalized The video is fine but there is no sound The audio is mute The quality of the picture is white and black and not coloured The DAS tuner doesn t memorize the settings The rear camera is not visible Multiconn Srl The 12V of the battery is missing on yellow wire The signal of the rear camera is not connected or the signal polarity is inverted Pag 22 of 23 The volume is too low Use active antennas of high quality to improve reception quality Check working status of antennas by pressing MENU 1 2 3 and control bars strength If necessary Invert the position of the antennas on the unit Refer to manual at pag 13 Check the connection of the antennas Check a better location for the antennas Shielded glasses compromise the reception Use function MENU 1 2 3 to find the good position and fix the antennas anew Refer to manual at pag 10 Check the connection of antennas and check the status with menu 1 2 3 It is not possible to watch listen digital TV radio in an area non covered Press vol to raise the volume Press vol to raise the volume The receiver in
15. tween unit and controller Power supply cut during upgrade Pag 20 of 23 DAS M44Cl User Manual EN PROBLEM POSSIBLE REASON SOLUTION The number of available channels is limited due to the local broadcasting system The availability of the channels may vary depending on the area In DVB T mode the number of channels is The signal quality of some channels not as much as TV is too low expected Some TV channels are not available Multiconn Srl Pag 21 of 23 Perform StandBy Scan mode to rescan the channels Refer to manual at pag 12 Use active antennas of high quality to improve reception quality Check working status of antennas by pressing MENU 1 2 3 and control bars strength lf 1 or more bars have a low level or there is the warning no signal disconnect and connect again the antenna and check in real time the Status of the bar Refer to manual at pag 13 Check a better location for the antennas If necessary invert the position of the antennas on the unit Shielded glasses compromise the reception If necessary install the antennas inside the bumpers of the car Use function MENU 1 2 3 to find the good position and fix the antennas anew Refer to manual at pag 10 Only free TV channels are available Pay TV channels are visible only if you have CI option Only the locally free TV channels can be seen They can differ depending on the area Refer to ma
16. uitable for the only models designed for this mode CI option e Insertthe CAM and CARD slot in the receiver e Wait and verify the correct operation of the Pay TV by selecting the pay channels in the TV List Multiconn Srl Pag 19 of 23 DAS M44Cl User Manual EN Trouble shooting Q amp A Most of the troubleshooting issues can be easily solved The common cases and their solutions are listed in the below table PROBLEM POSSIBLE REASON SOLUTION No picture no sound The remote control does not work The unit does not respond to remote control commands Multiconn Srl The power cable is not properly inserted into the unit The orange or green wires are wrongly connected Check the power wire connection Audio video input not connected Refer to manual at pag 5 The unit is not switched ON seas Check if the led is RED on the unit The unit is in stand by mode and press POWER button Push the button on remote control The unitis in AV1 or EXT source TV AV and check the status of the unit Select the TV function The Fuse crimped on yellow wire is Change the fuse burned out Check the remote battery Remote battery life is over No power Replace it Remote battery is inserted wrongly For proper insertion refer to the manual on page 8 Ensure there is no obstacle between the controller and the unit or light of neon lamp Unit damaged To be returned to assistance desk No line of sight be
17. user can choose if having these bars shown on the edge of the screen or not e Nation In Europe is preferable to use the standard Europe e RESET This function is used to reset the system to default factory settings Multiconn Srl Pag 12 of 23 DAS M44Cl User Manual EN Antennas Status and Check The antennas are essential for the reception of TV signal and it is therefore very important to check and verify their functionality over time e While watching a TV channel press Menu 123 e fthe 4 bars are similar this means that the antennas are working correctly E DAS HD rev 025c MultiConn FE 216 Anti Ant 2 e f1 or more bars are significantly scarce this means that the antennas have deteriorated and need to be replaced DAS HD rev 025c MultiConn FE 216 Ant Ant 2 Ant3 Ant4 DAS HD rev0 25e MultiConn FE 216 Ant No signal Ant2 Ant3 Ant4 Multiconn Srl Pag 13 of 23 DAS M44Cl User Manual EN TV List and Memo TV Channel List DAS system allows to get 2 different TV lists 1 The TV List is controlled directly by antenna no 1 Focus e This list is automatically updated in real time and it works like frequency auto scan e This list is also strictly linked to the memo TV channel list to grant the better function of RDS system combined to digital broadcast DVB T e This list is also updated in real time by all 4 antennas if the function Stand by scan
Download Pdf Manuals
Related Search