D6202B - Markertek
Contents
1. Regulatory and Safety Notices Before using this product and any associated equipment refer to the Important Safety Instructions listed below so as to avoid personnel injury and to prevent product damage Products may require specific equipment and or installation procedures be carried out to satisfy certain regulatory compliance requirements Notices have been included in this publication to call attention to these Specific requirements Symbols Meanings This symbol on the equipment refers you to important operating and maintenance servicing instructions within the Product Manual Documentation Failure to heed this information may present a major risk of damage or injury to persons or equipment The symbol with the word Warning within the equipment manual indicates a potentially hazardous situation which if not avoided could result in death or serious injury gt gt Warning The symbol with the word Caution within the equipment manual indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices gt Caution The symbol with the word Notice within the equipment manual indicates a situation which if not avoided may result in major or minor equipment damage or a situation which could place the equipment in a non compliant operating state gt Notice This symbol is used to alert the user that an e2. a class A Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense A N Changes or modifications to this equipment not expressly approved by Ward Beck Systems Ltd could void the user s authority to operate this equipment Notice CANADA This Class A digital apparatus complies with Canadian ICES 003 Cet appareil numerique de classe A est conforme a la norme NMB 003 du Canada EUROPE This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive 93 68 EEC INTERNATIONAL This equipment has been tested to CISPR 22 1997 along with amendments A1 2000 and A2 2002 and found to comply with the limits for a Class A Digital device This is a Class A product In domestic environments this product may cause radio interference in which case the user may have to take adequate measures Notice Maintenance User Serviceable Parts Routine maintenance to this openGear product is not
3. cause audible artefacts e Pressing the EQ Switches SW1 or SW2 will activate the appropriate yellow EQ LED to indicate this feature is activated e While the EQ Switches SW1 or SW2 are activated pressing it again will disable the EQ and the yellow EQ LED will go off LEDs The front edge of the card features LEDs that display the status of the input signals As selections are made in the menus refer the subsequent chapter for complete menu descriptions the LEDs display the status of the input signals Descriptions are provided in the following table Lock 1 Green Top of the card When illuminated there is a valid AES EBU signal at the input of AES1 No Lock 1 ER Second from the top When illuminated a valid EC is not present at the input When illuminated this indicates that the cable EQ for AES 1 has been EQ 1 Yellow Third from the top inserted by pressing SW1 or that feature has been enabled through Dashboard Fourth from the top When illuminated there is a valid signal at the input of AES No Lock 2 ER Fifth from the top When illuminated a valid es is not present at the input When illuminated this indicates that the cable EQ for AES 2 has been EQ 2 Yellow Sixth from the top inserted by pressing SW2 or that feature has been enabled through Dashboard Com When illuminated this indicates that the D6201B is communicating to Activity SESCH Dashboard through the CAN bus Error Eighth from the top When illuminated this indicates that there is
4. required This product contains no user serviceable parts If the module does not appear to be working properly please contact Technical Support using the numbers listed under the Contact Us section on the last page of this manual All openGear products are covered by a generous 5 year warranty and will be repaired without charge for materials or labor within this period See the Warranty and Repair Policy section in this manual for details Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources Ward Beck Systems Ltd encourages you to use the appropriate take back systems These systems will reuse or recycle most of the materials from your end of life equipment in an environmentally friendly and health conscious manner The crossed out wheeled bin symbol invites you to use these systems lf you need more information on the collection reuse and recycling systems please contact your local or regional waste administration Introduction Overview The D6202B is a Dual AES EBU distribution amplifier designed for broadcast use It can provide four copies of each incoming signal when used with a T6303A rear assembly It may also be used to pr
5. D6202B OPENGEAR DUAL 1 X 4 AES EBU DISTRIBUTION AMPLIFIER 110 OHM WITH SRC User Manual Dies NU D UGDA u SUPP EEE ait ras C45 C47 com actnaTy E A a a ERROR D KS sa F Ce s umh SSR T jhje Wu gt ou J cse openGear _06202A Iss Frame 926 Pou kb by Ward Beck Systems Rev Jan 01 2015 Ward Beck Part Number D6202B e Document Issue 1 e Printed in Canada The information contained in this User Manual is subject to change without notice or obligation Copyright 2015 Ward Beck Systems Ltd All rights reserved Contents of this publication may not be reproduced in any form without the written permission of Ward Beck Systems Ltd Reproduction or reverse engineering of copyrighted software is prohibited Notice The material in this manual is furnished for informational use only It is subject to change without notice and should not be construed as a commitment by Ward Beck Systems Ltd Ward Beck Systems Ltd assumes no responsibility or liability for errors or inaccuracies that may appear in this manual Trademark A O 8 N wE is a registered trademark of Ross Video Limited amp D A J gt Se is a registered trademark of Ward Beck Systems Ltd All other product names and any registered and unregistered trademarks mentioned in this manual are used for identification purposes only and remain the exclusive property of their respective owners Important
6. an error in the communications to Dashboard through the CAN bus Table 1 Status LED Descriptions DIP Switch Settings Ei SWZ Ewe SVM SWS sie FAT Swe M e Moie ome one Reserved Reserved Detauk dip sw irme mar Gashbosrnd amable 1 x 8 with SRC On Off Note Using this feature disables tone generation Tone 1 Turns tone generator in AES 1 on Turns tone generator in AES 1 off Tone 2 Turns tone generator in AES 2 on Turns tone generator in AES 2 off Default power up default parameter settings On Get card parameters from non volatile memory ignore dip switch settings Configurable with Dashboard Control system Get card parameters from the Dip switch Dashboard Enable On Only card status is available on Dashboard users are prevented from changing parameters Off Normal operation users have full access to the cards parameters Remote Control DashBoard Control This card may be monitored or controlled by a remote computer through DashBoard the free configuration monitoring software available to openGear users With DashBoard installed on your computer the following menus are available when interrogating a D6202B card ITEM DISPLAY DESCRIPTION Product D6202B Product identification code Wu lt Balanced AES Name AudioDistribution Product functional description Amplifier Supplier Ward Beck Systems Ltd Manufacturer of the card Software Two digit software revision code W
7. eb site Manufacturer s web address Green Dot OK Card is functioning properly and appropriate signals are connected Red Dot No AES signal detected Card Status Locked AES signal is present Read AES Input Card Info Read Only Card Status AES signal is not present at either input Only 1 Unlocked AES signal is not present AES Input 2 Unlocked AES signal is not present MENU ITEM BUTTON SELECTION DESCRIPTION x4 Mode Card Functions as dual 1 in 4out AES DA Functions as a 1 in 8 out AES DA with Sample Rate Conversion 1x 8 wISRC A sampling signal must be connected to AES input 2 or jumpers on card may be set to select between AES2 or frame reference 1 or 2 Settings Button selection AES INPUT 1 MENU ITEM DISPLAY DESCRIPTION Enabled Equalizer is on to assist in recovering signals over long cable runs Card Equalizer Settings Disabled Cable equalizer is turned off selection Ton Enabled Tone generator for AES 1 turned on EE Disabled Tone generator for AES 1 turned off AES INPUT 2 MENU ITEM DISPLAY DESCRIPTION Enabled Equalizer is on to assist in recovering signals over long cable runs Equalizer Disabled Cable equalizer is turned off selection Tone Enabled Tone generator for AES 2 turned on SNE Disabled Tone generator for AES 2 turned off Card Settings Technical Specifications DIGITAL INPUT Resolution 24 Bit Input Level 0 2 7 V p p Input Impedance transforme
8. ibed in the following note handling circuit boards in high static environments such as carpeted areas and when wearing synthetic fiber clothing Always exercise proper grounding precautions when working on circuit boards and related equipment Static discharge can cause serious damage to sensitive semiconductor devices Avoid ESD Susceptibility Unpacking Unpack each D6202B you received from the shipping container and check the contents against the packing list to ensure that all items are included If any items are missing or damaged contact your sales representative or Ward Beck Systems Ltd directly Rear Module Options There are two rear module options available for the D6202B AES EBU distribution amplifier On the 20 slot OG3 FR C frame the T6303A rear module occupies two slots and provides I O for one D6202B card For higher density applications the T6403A rear module occupies two slots and provides I O for two D6202B cards All connections are 110 Ohms and are made on Phoenix pluggable screw terminal type connectors Single Card Dual Card T6303A T6403A D6202A E ve FE e Rear Module Sg ee an Options ans E G races E DI Leen one ES sme EB ses Figure 2 Rear Module Terminations Board Installation Use the following procedure to install the D6202B in an openGear OG3 FR C Series frame 1 Refer to the User Manual of the openGear OG3 FR C series frame to ensure that the frame is properly instal
9. lectrical or electronic device or assembly is susceptible to damage from an ESD event A ESD Susceptibility Important Safety Instructions This product is intended to be a component product of the openGear 8000 series frame Refer to the openGear 8000 series frame User Manual for important safety instructions regarding the proper installation and safe operation of the frame as well as it s component products gt Caution Certain parts of this equipment namely the power supply area still present a safety hazard with the power switch in the OFF position To avoid electrical shock disconnect all A C power cords from the chassis rear appliance connectors before servicing this area gt Warning Service barriers within this product are intended to protect the operator and service personnel from hazardous voltages For continued safety replace all barriers after any servicing This product contains safety critical parts which if incorrectly replaced may present a risk of fire or l electrical shock Components contained within the produc s power supplies and power supply area Warning are not intended to be customer serviced and should be returned to the factory for repair gt To reduce the risk of fire replacement fuses must be the same type and rating Only use attachments accessories specified by the manufacturer EMC Notices US FCC Part 15 This equipment has been tested and found to comply with the limits for
10. led according to instructions 2 When using the D6202B with the T6303A for maximum I O please note that the even numbered slots are to be used Plug the D6202B modules into slots 2 4 6 8 10 12 14 16 18 and 20 fora maximum of 10 cards Slot 1 is the left most slot as you look into the frame from the front 3 When using the D6202B with the T6403A for maximum density you may insert the card into any slot for up to 20 cards per frame 4 After selecting the desired frame installation slot hold the D6202B card by the edges and carefully align the card edges with the slots in the frame Then fully insert the card into the frame until the rear connection plugs are properly seated on the midplane and rear module This completes the procedure for installing the D6202B in an openGear OG3 FR C Series frame User Controls User Control Diagram Lock 1 LED No Lack 1 LED EQ 1 LED Lack 1 LED No Lock 3 LED EQ 2 Swatch EL 2 LED COMM Actwity LED Error LEO Figure 3 Card edge User Controls EQ Switch SW1 and SW2 The EQ Switches SW1 and SW2 are used to insert the cable equalizer into the incoming AES EBU signal The D6202B can recover digital audio signals conforming to AES EBU specifications and transmitted over 110 Ohm twisted pair cable up to 100 metres 300 ft long without equalization For cable lengths in excess of 100 metres we recommend that the input equalization be activated Note that switching the EQ in and out can
11. o Ontario M1V 5E1 V 416 335 5999 F 416 335 5202 Toll Free 800 771 2556 Website www ward beck com E Mail sales ward beck com Ordering Information Standard Equipment e D6202B AES EBU Distribution Amplifier 75 Ohm Optional Equipment e D6202BUM AES EBU Distribution Amplifier 75 Ohm User Manual additional User Manual T6301A Single Card Rear Module for installation into OG3 FR C frame for maximum I O T6401A Dual Card Rear Module for installation into OG3 FR C frame for maximum density e OG3 FR C Digital Products Frame and Power Supply with Cooling Fans 2RU holds up to 20 cards Your D6202B Distribution Amplifier is a part of the openGear family of products Ward Beck offers a full line of openGear terminal equipment including distribution conversion monitoring muxing demuxing and processing of AES EBU and HD SD SDI as well as analog audio and video products
12. ovide up to eight outputs that are sample rate converted When used with the T6403A up to twenty 1 x 4 AES DA s with SRC can be provided in a single two rack unit frame The D6202B supports audio sampling frequencies from 30kHz to 192 kHz Cable equalization and reclocking techniques enable the D6202B to recover the incoming digital audio signal reliably The D6202B is housed in the openGear OG3 FR C series frames Functional Block Diagram i kb Ze Ze H 5 l ir ir Ce Oe O CH a EF D T eh H r L Tanegnngeg Figure 1 Simplified Block Diagram of the D6202B Functions Features The following features make the D6202B the best solution for digital audio distribution e Cable equalization and data reclocking on the incoming AES EBU signal e Supports audio sampling frequencies from 30kKHz to 192 kHz e Provides sample rate conversion e Higher density with up to 20 cards with SRC in a OG3 FR C frame e 9 year warranty e Fits openGear OG3 FR C series frames Documentation Terms The following terms are used throughout this guide e Frame refers to the OG3 FR C frame that houses the D6202B card e Operator and User refer to the person who uses the D6202B e Board and Card refer to the D6202B card itself including all components and switches Installation and Setup Static Discharge Whenever handling the D6202B and other related equipment please observe all static discharge precautions as descr
13. plied warranties are expressly limited to the duration of this warranty This openGear D6202B User Manual provides all pertinent information for the safe installation and operation of your openGear Product Ward Beck policy dictates that all repairs to the openGear D6202B are to be conducted only by an authorized Ward Beck Systems factory representative Therefore any unauthorized attempt to repair this product by anyone other than an authorized Ward Beck Systems factory representative will automatically void the warranty Please contact Ward Beck Technical Support for more information In Case of Problems Should any problem arise with your openGear D6202B please contact the Ward Beck Technical Support Department Contact information is supplied at the end of this publication A Return Material Authorization number RMA will be issued to you as well as specific shipping instructions should you wish our factory to repair your openGear D6202B If required a temporary replacement module will be made available at a nominal charge Any shipping costs incurred will be the responsibility of you the customer All products shipped to you from Ward Beck Systems Ltd will be shipped collect The Ward Beck Technical Support Department will continue to provide advice on any product manufactured by Ward Beck Systems beyond the warranty period without charge for the life of the equipment WARD BECK SYSTEMS LTD 945 Middlefield Road Unit 9 Toront
14. r balanced 110 Ohm HiZ Sampling Frequency Range 30 kHz to 192 kHz DIGITAL OUTPUT Resolution 24 Bit Output Level 2 5 V p p nominal Output Impedance 110 Ohm balanced Sampling Frequency Range 30 kHz to 192 kHz Jitter Less than 5 ns GENERAL Power Requirements 12 V 4 Watts MAX Dimensions 3 025 high x 12 800 deep Weight approx 0 115 kg 0 252 Ibs NOTE Ward Beck Systems Ltd reserves the right to change performance specifications without prior notice Warranty and Repair Policy The openGear D6202B is warranted to be free of any defect with respect to performance quality reliability and workmanship for a period of FIVE 5 years from the date of shipment from our factory In the event that your openGear D6202B proves to be defective in any way during this warranty period Ward Beck Systems Ltd reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics Should you find that this openGear D6202B has failed after your warranty period has expired we will repair your defective product should suitable replacement components be available You the owner will bear any labor and or part costs incurred in the repair or refurbishment of said equipment beyond the FIVE 5 year warranty period In no event shall Ward Beck Systems be liable for direct indirect special incidental or consequential damages including loss of profits incurred by the use of this product Im
Download Pdf Manuals
Related Search