LINĒA-PRO 4
Contents
1. Barcode type is not supported INFINITE USER MANUAL 20 ERIPHERA FEDEHAL COMMUNICATIONS COMMISSION Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Operation is subject to the following2. When using the Lin a pro 4 care must be taken to ensure the Lin a pro 4 30 pin connector and the iPod and iPhone connector are not accidentally damaged The figures below show how to attach your device to the Linea pro 4 mw 1 Unlock the top cover as shown in figure above 2 Slide the device as shown in the figure above 5 Replace the top cover as shown in the figure above LJ INFINITE USER MANUAL 12 FEATURES 1D BARCODE SCANNING Using the 1D Barcode Scanner The Linea pro 4 1D uses a scan engine that supports one dimensional 1D barcode symbols The effective reading distance of the barcode reader varies depending on the barcode size Scanning 1D Barcodes To scan a 1D barcode fist activate the scanner Then position the scan head as close to the barcode label as possible so that the scan line crosses both ends of the barcode as shown in the figure below Slowly pull back the unit increasing the distance between the barcode and scan head until the barcode has been read by the scanner Scan button 15 20 cm Ka 123456 INFINITE USER MANUAL 13 mE FEATURES 2D BARCODE SCANNING Using the 2D Barcode Scanner The Linea pro 4 2D uses a scan engine that supports one dimensional ID and two dimensional 2D barcode symbols The effective reading distance of the barcode reader varies depending on the barcode size Scanning 2D Barcodes To scan a 2D b
3. ipcprint com INFINITE USER MANUAL 18 hd l TROUBLESHOOTING CARD READING If you are having a problem reading the magnetic strip refer to the table below for possible causes Problem Possible Cause Linea pro 4 not turned On Card inserted incorrectly No card data returned during Swipe method incorrect swiping Faulty read head Unreadable magnetic strip Swipe method incorrect Partial card data returned during Faulty read head swiping Unreadable magnetic strip INFINIT USER MANUAL 19 ERIPHERA e m TROUBLESHOOTING BARCODE SCANNING If you are having problems scanning barcodes refer to the table below for possible causes Item Problem Possible Cause Linea pro 4 battery is to low Scanner does not turn On Linea pro 4 not turned on by software Faulty scan engine Unreadable barcode Linea pro 4 battery is to low No barcode data returned during scanning Faulty scan engine Software decode incorrectly Unreadable barcode Partial barcode data Linea pro 4 battery is to low returned during scanning paulerscancagine Software decode incorrectly Unable to perform multi Multi scan mode not enabled SIEHE Software does not support multi scans Unable to hear scanner Sound mode not enabled Deep Linea pro 4 battery is to low Unable to scan certain Barcode type is not enabled barcodes symbols
4. pro 4 MSR 2D BT L INFINITE Description Linea pro 4 with 3 Track mag stripe reader Linea pro 4 with 3 Track mag stripe reader and 1D barcode scanner Linea pro 4 with 3 Track mag stripe reader and 2D barcode scanner Linea pro 4 with 3 Track mag stripe reader and 1D barcode scanner and Bluetooth Linea pro 4 with 3 Track mag stripe reader and 2D barcode scanner and Bluetooth USER MANUAL 2 CONTENTS Compatability 1 Overview 4 Features Technical Data 5 General Specifications 5 Box Contents 6 Software Drivers amp SDK 6 Getting Started 7 Quick Start Guide 7 About Your Linea pro 4 8 Battery Charging 10 Status and Operational Modes 11 Attach Linea pro 4 12 Features 13 1D Barcode Scanning 13 2D Barcode Scanning 14 Magnetic Card Reader 15 Replace battery 16 Syncing 17 Developing Applications 18 Troubleshooting 19 Card Reading 19 Barcode Scanning 20 Federal Communications commission 21 um s USER MANUAL 3 OVERVIEW Linea pro 4 allows mobile workers to convert their iPod touch and iPhone handset into a powerful point of sale solution The Linea pro 4 includes optional 1D or 2D barcode scanner 3 tracks magnetic stripe reader and a rechargeable battery extender in a very compact and durable protective case FEATURES Battery Rechargeable Li ion Battery 1500 mAh Charging via USB to computer or Charging Station to Linea pro 4 Provides auxiliary power to iPod touch and iPhone Magnetic Card Re
5. C EAN 128 EAN 13 EAN 8 UPC A UPC E UPC E1 Code 11 Code 39 Code 93 Code 128 GS1 Matrix 2 to 5 Code 11 2 of 5 industrial 2 of 5 interleaved Codebar MSI Plessey UK Plessey IATA ISBN ISMN ISSN S code Telepen RSS 14 RSS Limited RSS Expanded PDF417 microPDF417 Data Matrix QR code Aztec code Maxi code Micro QR code LEDs 5 green LEDs for status of Battery Charging and status of the Device Rechargeable Li ion Battery 3 7V 1300mAh 1D Over 14 000 scan and swipes per full charge 2D Over 8 000 scan and swipes per full charge Audio Indicator Electro Magnetic Buzzer 95 grams without iPod iPhone 250 grams with iPhone 197 grams with iPod 125mm x 67mm x 19 to 252mm depends on scanner 1D 2D amp Dimensions mm device Operating temperature O C to 40 C Operating humidity 35 to 85 RH Barcode Type Battery Weight g Environment Storage temperature 5 C to 40 C Storage humidity 10 to 90 RH Cables Standard USB A to mini B CABLE Specifications subject to change without notice INFINITE USER MANUAL 5 e Ff BOX CONTENTS Your Linea pro 4 will ship with the items listed below Descriptions Image Lin a pro 4 USB sync cable Fm Bulk shipments may ship without cables in each box SOFTWARE DRIVERS amp SDK Because of the continually evolving SDK the latest SDK are not distributed on CD For the latest Linea pro 4 SDK s please visit our Lin
6. INFINITE PERIPHERALS Lb Ocid V3NI 1 Up BU lt gt A gt ra LINEA PRO 4 iPhone IPod Touch 1D 2D SCANNER Made for iPod Q iPhone CONTACT INFORMATION National Sales Headquarters HQ and Main Distribution Facility Technical Support Infinite Peripherals Inc 1124 Main Street Suite B Irvine CA 92614 Toll Free 866 278 7860 Office 949 222 0300 Fax 949 222 0375 Infinite Peripherals Inc 3104 N Arlington Heights Road Arlington Heights IL 60004 Toll Free 800 278 7860 Phone 847 818 1260 Fax 847 818 1287 Infinite Peripherals Inc 1124 Main Street Suite B Irvine CA 92614 Office 949 222 0300 Fax 949 222 0375 Email info ipcprint com ipcprint com INFINITE PERIPHERALS LEGAL NOTICE PERIPHERA Made for iPod Made for iPhone and Made for iPad mean that an electronic accessory has been designed to connect specifically to iPod iPhone or iPad respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod iPhone or iPad may affect wireless performance COMPATABILITY Made for iPod touch 4 generation iPhone 4 iPhone AS LINEA PRO 4 MODELS Model Linea pro 4 MSR Linea pro 4 MSR ID Linea pro 4 MSR 2D Linea pro 4 MSR ID BT Linea
7. Scan Button User Notes Special software must be used to process the information captured by the barcode scanner and magnetic strio reading feature Please consult your reseller for this software or contact Infinite Perioherals for recommendations on compatible third party software solutions hd INFINITE USER MANUAL 9 BATTEHY CHARGING Charging the Linea pro 4 The Linea pro 4 uses a Lithium lon rechargeable battery Before first use the battery pack should be charged for at least 4 hours To prevent electrical damage to the Linea pro 4 and or battery please use approved USB to Mini USB cables only Charging via USB cable type A to mini USB connected to PC 5V 260mA 1 LED 33 96 of full charge 2 LED 66 of full charge 5 LED 100 96 of full charge LJ INFINITE USER MANUAL 10 STATUS AND OPERATIONAL MODES The Linea pro 4 uses the battery indicator LEDs to indicate various conditions of operation Possible LED lighting indications may result from charging active online status or because of low battery The following table and figure explain these conditions and LED indication Battery Status Button Operating Status Lin a Aisi All LED is OFF inea pro is in sleep or ready mode Middle LED is FLASHING Linea pro 4 is in sync mode Linea pro 4 is displaying battery Multiple LED is ON Sue level status INFINITE USER MANUAL 11 Md l ATTACH LINEA PRO 4
8. ader 5 Track Head Swipe Speed Minimum of 1 97 in sec MTBF 1 million swipes Bidirectional reading capabilities Barcode Scanner Class Il ID Laser 2D Imager Single Multi scan mode 1D MTBF 30K hours Laser Diode amp Mirror Unit 10K hours 2D MTBF 5OK hours Imager amp Laser Pointer amp Focus LED Indicators Audible Internal electro magnetic buzzer Visual 3 green LEDs I O Connectors 30 DIn plug iPod dock connector 10 pin female Mini B USB connector for charging and synchronization e INFINITE USER MANUAL 4 TECHNICAL DATA GENERAL SPECIFICATIONS Power Supply Internal Voltage 3 3V and 5V DbcisdenMsHes Active turn on Linea pro 4 Active with Scanning Stand By after bsec without operate MCU Hitachi HD64F3687 Memory 512k I2C EEPROM memory for Linea pro 4 settings CHEESE RS232 Interface communication between Linea pro 4 amp iPod iPho USB Interface USB Synchronization between iPhone iPod amp PC Speed 57600bps iPod RS232 Protocol RS232 Interface Active with Scanning 1D Engine 110mA 2D Engine 220mA Power Consumption Active approximately 25mA Stand by 1OuA Volume Up Button Volume Down Button Status Battery Button Buttons Scan Button Magnetic Stripe 5 track bidirectional reading capabilities Reader Type ISO 7816 1 2 3 compatible amp RAW mode Barcode Reader MDL 1000 Laser Scan Engine ID Barcode MDI 2000 Auto focus Imager Scan Engine 2D Barcode UC
9. arcode fist activate the scanner Then position the scan head to center the red aiming laser near the center of the barcode and the illumination box is over the outer edges of the barcode as shown in the figure below Slowly pull back the unit increasing the distance between the barcode and scan head until the barcode has been read by the scanner KR 15 20 cm Scan Button INFINITE USER MANUAL 14 mE FEATURES MAGNETIC CARD READER he Lin a pro 4 has a built in magnetic card reader The card reader incorporates a 3 track magnetic read head requiring a single swipe to read field data from all three tracks The magnetic read head faces up towards the top of the cradle When placing the card into the reader the magnetic strip must be facing up as shown in the figure below Keep the edge of the card flat on the inner base of the reader to ensure that the magnetic strip passes over the read head evenly Swipe direction User Notes To use the magnetic card reader feature special software must be used to read and process the card information Please consult your reseller if this software is available or contact Infinite Peripherals for recommendations on compatible third party software solutions LJ INFINITE USER MANUAL 15 HEPLACE BATTERY To replace the Linea pro 4 battery follow the steps below 1 Remove the device as shown in the figure below 2 Squeeze battery cover latch to the left as
10. ea pro developer portal http dev ipcprint com INFINITE USER MANUAL 6 GETTING STAHTED The Linea pro 4 allows customers to scan barcodes and capture magnetic strip information into the iPod and iPhone Before using your Linea pro 4 the battery should be properly charged The following table will help to get your Linea pro 4 ready for use QUICK START GUIDE Where to find more Step What to do Purpose information The battery pack Fully charge your should be fully Linea pro 4 as charged before use Charging Battery Page 1O recommended to ensure long battery life Software is not provided with Linea pro 4 Please contact your reseller or Infinite Peripherals for amp Card Reading suggestions on Third Party Barcode Scanning Install Software software solutions requires software to be installed onto Developers should refer to the your iPod or iPhone eode i section in this manual on Developing Solutions Page 18 Connecting your Lin a pro 4 and iPod Attaching Device Page 12 iPhone Attach device to Lin a pro 4 INFINIT USER MANUAL 7 ERIPHERA e m ABOUT YOUR LINEA PRO 4 Linea pro 4 Right Side On Off Ps Volume Scan Controls Engine Linea pro 4 Left Side USB Sync Charge Port ea Audio Connector Scan Button INFINITE USER MANUAL 8 PERIPHERALS ABOUT YOUR LINEA PRO 4 Lin a pro 4 Bottom Side a Scan Engine
11. shown in the figure above 5 Lift the battery cover as shown in the figure above Remove the existing battery Reverse Steps 1 2 to install the new battery Notice Use only factory recommended replacement battery to prevent damage to the Linea pro 4 LJ INFINITE USER MANUAL 16 SYNCING he Linea pro 4 portable barcode scanner and card reader is designed specifically for use with iPod iPhone there by allowing the iPod and iPhone to sync with iTunes through the Linea pro 4 while connected To sync iPod with iTunes through the Linea pro 4 follow the steps below 1 Connect the Linea pro 4 to a computer using a Mini USB cable as shown in the figure below 2 Wait for the sync mode 2 beeps and the center LED flashes green The Linea pro 4 should now be in sync mode Refer to the iTunes documentation for syncing your iPod and iPhone Sync Mode LED T To disable sync mode exit iTunes then unplug the Linea pro 4 from the Mini USB cable INFINITE USER MANUAL 17 IPI hd 4 DEVELOPING APPLICATIONS Integrating the Linea pro 4 into your app requires the use of the Linea pro 4 SDK The SDK incorporates an API specifically for developing applications to use the barcode scanning and card reading capability of the Linea pro 4 For details on using the Linea pro 4 SDK please refer to the SDK s documentation For the latest Linea pro 4 SDK s please visit our Linea pro developer portal http dev
12. two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Md 4 INFINITE USER MANUAL 21
Download Pdf Manuals
Related Search