LCD Monitor - NetShop AS
Contents
1. consists of three subpixels red green and blue so there are almost 6 2 million subpixels in total According to ISO 9241 3 Class I a maximum of 2 lit and 2 unlit pixels plus 5 lit or 10 unlit subpixels or a corresponding combination may be faulty 1 lit subpixel counts as two unlit subpixels 10 Fujitsu Technology Solutions co FUJITSU Copyright Fujitsu Technology Solutions 2011 01 Published by Fujitsu Technology Solutions GmbH Mies van der Rohe StraRe 8 80807 Miinchen Germany Contact http ts fujitsu com support All rights reserved including intellectual property rights Technical data subject to modifications and delivery subject to availability Any liability that the data and illustrations are complete actual or correct is excluded Designations may be trademarks and or copyrights of the respective manufacturer the use of which by third parties for their own purposes may infringe the rights of such owner For further information see http ts fujitsu com terms of use html Fujitsu Technology Solutions Order No A26361 K333 Z120 1 7619 Edition 12. E conformance and optimum picture quality are guaranteed only if you use the data cable supplied No data transfer cables should be connected or disconnected during a thunderstorm Make sure that no objects e g jewellery chains paper clips etc or liquids get inside the device danger of electric shock short circuit The device is not waterproof Never immerse the device in water and protect it from spray water rain sea water In emergencies e g damaged casing elements or cables penetration of liquids or foreign matter switch off the unit disconnect the power plug and contact your sales outlet or our Service desk Fujitsu Technology Solutions Important notes The monitor must be disposed of in accordance with the local regulations for disposal of special waste The screen background lighting contains mercury You must observe the applicable handling and disposal safety regulations for fluorescent tubes Only qualified technicians should repair the device Unauthorised opening and incorrect repair may greatly endanger the user electric shock fire risk Use a screen saver with moving images and activate the power management for your monitor to prevent still images from burning in The screen may only be operated in the wide format 0 landscape mode Turning with a swivel arm or wall bracket mounted is not permitted Store this manual close to the device If you pass the device on to third parties you should pa
3. Operating Manua LCD Monitor co FUJITSU Copyright Fujitsu Technology Solutions GmbH 2011 VESA DDC and DPMS are registered trademarks of Video Electronics Standards Association All other trademarks used in this document are trademarks or registered trademarks of their respective owners and are recognised as being protected All rights including rights of translation reproduction by printing copying or similar methods even of parts are reserved Offenders will be liable for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved Contents Introduction ac O zdaze da oda Ado dw 1 Target group natki owak t ce te t re ta AA OZ W OW ER W AAAA CER AA 1 Notational CONVENTIONS eene enne tn detnr thon dne inea ink nda p ina n ko inna e ER E Eee ane d ina san kou 1 Additional inTOLtatior a rena an ba eer ent PA e RS DO TO i nd 1 Important Notes e 2 SafelVTiOl S t ccntum cus e tea Nz sec PRO aa SA AA MA SME e 2 ie gelo is a eraa aae d AEA aea A i a aa E E aa AA EAE Eee Aa daaa Ean 3 Tran SpOFt In oerte rete A eno EP RO O A E eee 3 GSM csc EEA ae ED LM ccena M LL PM A REED DIM MAT LIEN 4 iei EI DIR 4 FCC Class B Compliance Statement ssssssssessessseseeeeeee enne tente nnne 4 Checking the contents
4. ed here However please observe the safety information given in the operating instructions of the computer and in this manual In the event of any problems occurring please contact your sales outlet or our Service desk Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to text marked with this symbol Failure to observe this warning endangers your life destroys the device or may lead to loss of data i Supplementary information remarks and tips follow this symbol gt Text which follows this symbol describes activities that must be performed in the order shown Quotation marks indicate names of chapters or terms This font indicates filenames and menu items This font indicates screen outputs Additional information Details of how you set the resolution and refresh rate are provided in the documentation on your screen controller the associated driver software Fujitsu Technology Solutions 1 Important notes Important notes In this chapter you will find information regarding safety which is essential to take note of with your monitor Safety notes This device complies with the relevant safety regulations for data processing equipment including electronic office machines for use in an office environment If you have any questions contact your sales outlet or our Service desk The display surface of the LCD monitor is sensitive to press
5. ge using the computer software see documentation for your computer or your graphics card Adjust a different screen resolution using the computer software see documentation for your computer or your screen controller Picture position not correct The monitor recognises an undefined mode gt gt Carry out the auto adjustment of the monitor with the AUTO button if present or via the OSD menu Set the picture position with the OSD menu Fujitsu Technology Solutions Operation of the monitor Having this problem Check the following points Picture is shaking gt Check whether the data cable for the monitor is correctly attached to the monitor port on the computer gt Carry out the auto adjustment of the monitor with the AUTO button if present or via the OSD menu Picture disturbances vertical lines gt Carry out the auto adjustment of the monitor with the AUTO button if present or via the OSD menu t Mg Picture disturbances gt Carry out the auto adjustment of the monitor with horizontal lines picture noise the AUTO button if present or via the OSD menu gt Carry out the auto adjustment of the monitor with Picture too light or too dark y J ius 9 the AUTO button if present or via the OSD menu gt Correctly set the contrast and brightness with the OSD menu if the auto adjustment function does not supply satisfactory re
6. of the consignment eeeee eee eee eee eene 5 Connecting the monitor tirer creer et deren 6 Connecting cables to the monitor sssesssssssssssseseeeseeeeeneee nennen eaaa iaeia ae naana ra inadai 6 Connecting cables to the computer ssessssssssessseseeeseee nennen enne rennen enn thn sein rns snnt snnt nnn 6 Operation of the monitor ssseeeeeaeeea anna aaa aaa zaawan wawa aaa aaa aa zza aaa sten snas tss siens sss n nnns 7 Adjusting rake Switching the monitor on off eee eee aaa aaa aaa aaa aaa aaa aaa awiza eter aan nena 7 Troubleshooting n arava detec ceo eR eee etse ey eoo ta ny apart nea nea 8 Explanatory information about standard ISO 9241 3 eese 10 Lit or unlit pixels a erdt ith ro tee Ee eie Uc ed Ee Lt o e 10 Fujitsu Technology Solutions Fujitsu Technology Solutions Introduction Introduction This manual contains important information for correct set up of your LCD monitor The LCD monitor is actuated from the PC The screen controller the associated driver software is responsible for setting the modes resolution and refresh rate When putting the monitor into operation for the first time the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs Target group You don t need to be an expert to perform the operations describ
7. or are free e The display surface of the LCD monitor is sensitive to pressure and scratches Clean it only using a soft slightly moistened cloth Wipe the monitor casing with a dry cloth If the monitor is particularly dirty use a cloth which has been moistened in mild domestic detergent and then carefully wrung out CE marking The shipped version of this device complies with the requirements of the EC directives C 2004 108 EC Electromagnetic compatibility and 2006 95 EEC Low voltage directive FCC Class B Compliance Statement The following statement applies to the products covered in this manual unless otherwise specified herein The statement for other products will appear in the accompanying documentation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference Causing Equipment Standard ICES 003 for digital apparatus These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in strict accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or
8. ss this manual on with it We recommend that you place your device on a durable non slip surface In view of the many different surface coatings and finishes used on furniture it is possible that the feet of the device could mark the surface they stand on Power cable To guarantee safe operation use the cable supplied Use the following guidelines if it is necessary to replace the original cable set The female male receptacles of the cord set must meet IEC60320 CEE 22 requirements The cable has to be HAR certified or VDE certified The mark HAR or VDE will appear on the outer sheath For devices which are mounted on a desk or table type SVT or SJT cable sets may be used The cable set must be selected according to the rated current for your device If necessary replace the original power cable with a regular grounded 3 core mains lead Transport Transport the monitor with care and only in its original packaging or another corresponding packaging fit to protect it against knocks and jolts Never drop the LCD monitor danger of glass breakage Fujitsu Technology Solutions 3 Important notes Cleaning e Always pull out the power plug before you clean the monitor e Do not clean any interior parts yourself leave this job to a service technician e Do not use any cleaning agents that contain abrasives or may corrode plastic e Ensure that no liquid will run into the system e Ensure that the ventilation areas of the monit
9. sults Fujitsu Technology Solutions Explanatory information about standard ISO 9241 3 Explanatory information about standard ISO 9241 3 Lit or unlit pixels Today s production techniques cannot guarantee an absolutely fault free screen display Depending on the total number of pixels resolution there may be a few constantly lit or unlit pixels or subpixels Pixel A pixel consists of 3 subpixels normally red green and blue A pixel is the smallest element that can be generated by complete functionality of the display Subpixel A subpixel is a separately addressable internal structure in a pixel which extends the pixel function The maximum permitted number of faulty pixels is stipulated in the international standard ISO 9241 3 In accordance with standard ISO 9241 3 LCD monitors by Fujitsu comply with Class II for low resolutions and Class for resolutions of 1680 x 1050 1764000 pixel and higher Examples A flat screen monitor with a resolution of 1280 x 1024 has 1280 x 1024 1310720 pixels Each pixel consists of three subpixels red green and blue so there are almost 3 9 million subpixels in total According to ISO 9241 3 Class Il a maximum of 3 lit and 3 unlit pixels plus 7 lit or 13 unlit subpixels or a corresponding combination may be faulty 1 lit subpixel counts as two unlit subpixels A flat screen monitor with a resolution of 1920 x 1080 has 1920 x 1080 2073600 pixels Each pixel
10. t the connector of the power cable supplied into a properly earthed mains outlet and ensure a secure connection gt Plug the power connector of the computer into a properly grounded mains outlet appropriate graphics drivers for your application software Details of how to do this are i When you start working with your monitor for the first time you should install the provided in the documentation on your screen controller the associated driver software 6 Fujitsu Technology Solutions Operation of the monitor Operation of the monitor Note that when screens with shiny front surrounds are positioned the surrounds may cause troublesome reflections from background light sources and bright surfaces Adjusting rake The rake of the monitor can be adjusted forward and back from its vertical position gt Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the desired rake Switching the monitor on off The ON OFF switch is used for switching the monitor on and off The power indicator glows green or blue when the monitor and computer are switched on The power indicator glows orange when the monitor does not receive a video signal or is in energy saving mode The power indicator goes off when the monitor is switched off When you switch the computer system on you must proceed in the following order gt First switch the LCD monitor on with the ON OFF switch gt Then switch on the compu
11. t the delivery does not correspond to the delivery note notify your local sales outlet immediately We recommend that you keep the original packaging material You may need the packaging in the future if you need to transport your device Fujitsu Technology Solutions 5 Connecting the monitor Connecting the monitor Please take note of the safety information in the Important notes chapter CE conformance and optimum picture quality are guaranteed only if you use the data cable supplied Do not cover the ventilation openings of the monitor The computer power plug must be pulled out gt Be sure that the monitor and the computer are switched off Connecting cables to the monitor gt Ifthe data cable is not firmly connected to the monitor Connect one of the connectors of the data cable to the D SUB connector on the monitor and secure the plug in connection by tightening the locking screws gt Plug the power cable supplied into the power connector of the monitor Connecting cables to the computer Information on the computer connections and interfaces is contained in the operating manual for your computer If your computer has two monitor ports onboard screen controller and separate graphics card the monitor port for the separate graphics card is usually active gt Connect the data cable to the active monitor port on the computer and secure the plug in connection by tightening the safety screws gt Connec
12. television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for Service Fujitsu Technology Solutions GmbH is not responsible for any radio or television interference caused by unauthorised modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu Technology Solutions GmbH The correction of interferences caused by such unauthorised modification substitution or attachment will be the responsibility of the user Ao Fujitsu Technology Solutions Important notes Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches Always hold the device by the casing gt Unpack all the individual parts gt Check the delivery for damage incurred during transportation Check whether the delivery agrees with the details in the delivery note The complete LCD monitor package includes one monitor data cable one power cable one Warranty Booklet this Getting Started manual Should you discover tha
13. ter Fujitsu Technology Solutions 7 Troubleshooting Operation of the monitor Should an error occur first check the following points If the distortion is still not eliminated the monitor should if possible be checked on another computer If you are unable to solve the problem please inform our Service desk Having this problem Check the following points No screen display b Check whether the monitor is switched on power indicator does not light gt Check whether the power cable on the monitor is connected correctly b Check whether the computer is switched on No screen display b Check whether the computer is switched on power indicator lights gt Check whether the data cable for the monitor is correctly attached to the monitor port on the computer b Press any key on the computer keyboard the computer may be in energy saving mode gt Alter the brightness and or contrast until you get a picture Message b Check whether the data cable for the monitor is No Video Input correctly attached to the monitor port on the o computer 5 b Check whether the computer is switched on No Signal Message The input signal horizontal frequency and refresh rate eg does not correspond to the technical monitor data This is 85 Hz overdrive Change computer display input to ils X at 60 Hz or Frequency out of range Please change the display mode to gt Adjust the video frequency ran
14. ure and scratches You should therefore be careful with the display surface so as to avoid lasting damage Newton rings scratches If the device is brought into the installation site from a cold environment condensation can form Before operating the device wait until it is absolutely dry and has reached approximately the same temperature as the installation site To ensure sufficient ventilation the intake and exhaust air openings of the monitor must never be blocked The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V Ensure that the local mains voltage lies within these limits Ensure that the power socket on the device or the grounded mains outlet is freely accessible The ON OFF switch does not disconnect the device from the mains voltage To completely disconnect the mains voltage remove the power plug from the socket The monitor is equipped with a power cable that complies with safety standards Lay all cables so that nobody can stand on them or trip over them When attaching the device observe the relevant notes in the Connecting the monitor chapter Wenn Sie eine andere als die mitgelieferte Datenleitung verwenden achten Sie darauf dass die Leitung ausreichend abgeschirmt ist CE Konformitat sowie eine optimale Bildqualitat werden nur mit der mitgelieferten Datenleitung gew hrleistet If you use a different data cable from the one supplied ensure that it is adequately shielded C
Download Pdf Manuals
Related Search