Owner/User Manual
Contents
1. In 30 seconds you will hear a single short chirp from the siren and the vehicle s parking lamps will flash one time indicating the system is ARMED At this time the dash mounted LED will begin to flash slowly providing a visual indication that the system is fully ARMED OPTION NOTE If the optional not included power door lock interface has been installed the alarm control module can be programmed to a Automatically lock the doors during step 3 above or b Lock the doors only when the transmitter is operated 4 If you wish to arm the system immediately simply press and release the ARMING button on the keychain transmitter The siren will chirp once the vehicle s parking lamps will flash once the doors will lock optional and the dash mounted LED will begin to slowly flash PROTECTION WHILE THE SYSTEM IS ARMED 1 Opening any door hood or trunk will cause the alarm to immediately sound The siren will continue to sound for 30 seconds then stop and automatically re arm the vehicle If the potential thief left a door opened the siren will sound for six 30 second cycles then re arm and ignore the opened door Any strong impact to the vehicle s glass will cause the alarm to trigger for the full 30 second alarm cycle with Dual Stage Any mild impact to the vehicle s glass will cause the alarm to sound a short series of warning tones Whenever the system is armed the dash mounted LED indicator will slowly flash2. Model APS 25CH GE Owner s Manual 2 Button Remote Security System Congratulations Your purchase of this state of the art security system expresses a deep concern for the security of your vehicle its contents and passengers To fully appreciate the many functions and safeguards incorporated in this system please spend a few minutes reading this manual You may find unexpected features that could mean the difference between protected and fully protected FEATURES 2 Two Button Programmable Code Hopping RF Transmitters Two Channel Receiver capable of accepting 4 transmitters Code Learning Remote Panic in all modes Protected Valet 7 Function LED Arm Disarm Zones 1 2 amp 3 Valet Arming Intrusion Alert with Memory Audible Arm Disarm Defective Zone Tamper Confirmation Instant Siren Activation Starter Disable True Last Door Arming hardwire only Defective Zone By Pass Hardwire or Voltage Sense Selectable Active or Passive Arming Selectable User Programmable Permanent Chirp Delete 6 Tone Multi Tone Siren Additional Negative Trigger Input RF Inhibit with Ignition On Parking Light Flasher Plug In Dual Stage Shock Sensor OPTIONS Remote Trunk Release Remote Keyless Entry Multiple Vehicle Capable Remote Starter Remote Power Window Roll Up Remote Garage Door Interface 128 6452 1of5 ARMING THE SYSTEM
3. This serves as a visual deterrent to the potential thief The LED is a very low current bulb and will not cause the vehicle s battery to drain even when left unattended for extended periods Page 2 128 6452 2 of 5 4 Whenever the system is triggered the vehicle s parking lights will flash for the 30 second alarm cycle attracting added visual attention to the vehicle 5 Whenever the system is armed the vehicle s starter will be bypassed If a thief should choose to ignore the siren the vehicle can not be started DISARMING THE SYSTEM 1 As you approach the vehicle press and release the ARMING button on the keychain transmitter WARNING Excessive pressure on the transmitter buttons will damage the internal components on the circuit board All that is required is a light push to the button 2 The siren will chirp 2 times and the vehicle s parking lamps will flash two times 3A ACTIVE The dash mounted LED will turn off and remain off until the system is re armed 3B PASSIVE Never attempt to disarm the system from a distance that prevents you from opening a door within 30 seconds Since the system is programmed for passive arming it will begin to re arm until a door is opened Opening the door will suspend the passive arming cycle INTRUSION WARNING SIGNALS The system will inform you if an intrusion attempt has occurred while you were away from the vehicle If an intrusion attempt has occurred the
4. ACTIVE 1 Turn off the engine exit the vehicle and close and lock all doors hood and trunk 2 Press and release the ARMING button on the keychain transmitter The siren will chirp once the vehicle s parking lights will flash once the doors will lock optional and the dash mounted LED will begin to slowly flash WARNING Excessive pressure on the transmitter buttons will damage the internal components on the circuit board All that is required is a light push to the button NOTE Ifthe siren chirped three times when ARMING then one of the entry points hood trunk doors has been left opened Closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction If the siren chirped three times sometime after arming the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired Again closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction ARMING THE SYSTEM PASSIVE 1 Turn off the engine exit the vehicle close and lock all doors hood and trunk 2 The dash mounted LED will begin to flash rapidly indicating that the system is automatically passive arming As an added convenience the automatic passive arming will not begin until all doors and trunk lid are closed allowing passengers to exit the vehicle at their convenience
5. by your installation center this output may be accessed by pressing buttons 1 amp 2 simultaneously for 3 seconds NOTE This feature will not operate when the vehicle s ignition key is turned ON Page 4 128 6452 4of 5 APS 25CH SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS DISARMED VALET MODE INTRUSION ZONE 3 INTRUSION ZONE 2 INTRUSION ZONE 1 SIREN CHIRP INDICATORS 2 CHIRPS ARM ZONE ACTIVE 4 CHIRPS DISARM INTRUSION PARKING LAMPS Optional Where applicable These chirps are optional and may be disengaged Your System Has These Features Activated 0 Starter Cut out Motion Detector Door Lock Interface Hardwire Q Shock Detector Optional Channel 2 Device 2003 Audiovox Electronic Corporation 150 Marcus Blvd Hauppauge N Y 11788 128 6452 Page 5 128 6452 5 of 5
6. ing the arming sequence or if the vehicle had been tampered with in your absence even if the normal arming and disarming chirps have been turn off REMOTE PANIC OPERATION The arming amp disarming button on your keychain transmitter also functions as a panic switch for instant activation of the alarm in emergency situations To use the remote panic switch 1 Press and hold the arming button on the keychain transmitter for 3 seconds or more The alarm will immediately sound 2 To stop the alarm press and release the arming button on the keychain transmitter If the button is not pressed the alarm will automatically stop after 30 seconds WARNING Excessive pressure on the transmitter buttons will damage the internal components on the circuit board All that is required is a light push to the button TRUNKRELEASE This security system has an additional feature that can be wired to a number of different optional accessories Some of the more common uses for this channel are Remote Trunk Release available for any vehicle with factory installed electronic push button trunk release Remote Car Starter available for most automatic transmission fuel injected vehicles Remote Window Roll Up available for most vehicles equipped with power windows To activate the optional accessory Press and hold the smaller button on the keychain transmitter for approximately 3 seconds If the system has been programmed differently
7. normal operation with the ignition switch on press and release the valet push button switch one time The LED will turn off indicating the unit has been returned to the normal mode of operation In the event you lose your keychain transmitter or if the transmitter fails to disarm the system the valet switch can be used as a system override switch Open the car door the alarm Page 3 128 6452 3 of 5 will sound Turn the ignition key on and press and hold the valet switch on The alarm will stop sounding and the vehicle can now be started NOTE Always remember to exit Valet Mode to ensure that the vehicle remains protected at all times ELIMINATING THE ARM DISARM CHIRPS The normal arming and disarming confirmation chirps can easily be turned on and off using the valet push button switch To do this 1 Turn the ignition key on and then off 2 Within 10 seconds of turning the ignition key off press and release the valet push button switch three times 3a If before proceeding with step 2 the chirps were on then you will hear 2 chirps to indicate that the chirps have been turned off 3b If before proceeding with step 2 the chirps were off then you will hear 1 chirp to indicate that the chirps have been turned on Note Whenever the chirps are by passed the 3 chirp defect and 4 chirp intrusion indicator will always operate This feature will always warn you if there is a defective sensor dur
8. siren will chirp 4 times when disarming the system The vehicle s parking lights will also flash 3 times to indicate an intrusion has occurred Enter the vehicle and observe the dash mounted LED for further information If the LED is flashing one time pause one time etc then an intrusion attempt was made to a light activated entry point or the shock sensor was activated If the LED is flashing two times pause two times etc then an intrusion attempt was made to the hood trunk or an optional sensor that has been connected to zone 2 If the LED is flashing three times pause three times etc then an intrusion attempt was made through one of the vehicle s doors These intrusion warning indicators are stored in the system s memory and will only be erased from memory when the ignition key is turned on VALET SYSTEM OVERRIDE SWITCH The Valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm functions are bypassed however the remote panic feature and remote door locks optional will remain operational To use the valet mode 1 Enter the vehicle and turn the ignition key to the on position 2 Press and hold the valet push button switch for 5 seconds until the dash mounted LED turns on solid The LED will remain on as long as the system is in the valet mode 3 To return to
Download Pdf Manuals
Related Search