User Manual - Adrenio Trading
Contents
1. Mode 1 The ts files will be saved in 188 byte packages with null packet embedded Mode 2 The ts files will be saved in 188 byte packages with null packet filtered However such ts files cannot be normally played with NDS3558A but can be played on PC with some media player such as VLC Mode 3 The ts files will be saved in 204 byte packages with null packet filtered Playing Auto Mode Auto Mode is for saving the play mode for the device When the auto mode is enabled the device will automatically apply the play mode set before the power cut off and output ts files stored in the USB device through IP While the auto mode is off NDS3558A will play the encoded TS through RF when the power is connected Parameters gt NMS From the menu on left side of the webpage clicking NMS it displays the interface where users set the network configuration for the device Figure 6 Network Encoder welcome to u 2015 07 10 10 21 10 EN HX Exit Status IP Address The manege address use this address to visit the manege web The format is HAAK like as 192 168 0 1 After set the IP address you must use the NMS Encoder new address to visit the manage web IP Stream USB Subnet Mask NMS General is 255 255 255 0 it is must the same in a local area network LCD Key Gateway If the device is in different net segment you must set the gateway H Web Manage Port The default web manage port is 80 if you chan2. CHAPTER 4 Devices Operations and Management NDS3558A is controlled and managed through the key board and LCD display USB ENTER MENU LOCK etess LCD Display It presents the selected menu and the parameter settings The backlight in the display is on when the power is applied LED Indicators These lights indicate the working status Power It lights on when the power supply is connected Alarm It lights on when the there is error such as the signal source loss USB It lights on when the USB device is properly connected and blocks out when the USB device get removed Left Right Up Down buttons Use these buttons to turn the screen pages shift the target items by moving the triangle or change the parameter settings in the program mode Enter Use this button to enter a submenu or save a new setting after adjustment press it to start adjusting the value of certain items when the corresponding underline flash with Up and Down buttons Hue Enter Hue lt gt Hue Hue 1 001 001 002 Press it to activate the hidden selections and change the setting with Up and Down or Left and Right buttons Audio Bit rate Enter Audio Bit rate Enter Audio Bit rate 7 Audio Bit rate 128 128 gt 128 gt 192 Menu Press this button to step back Lock Locking the screen cancelling the lock state and entering the main menu after the initialization of the device After pressing lock key
3. Safari browser when HLS is applied as the output protocol no need any 3 party player Note Android devices need to install HLS plug in to play when HLS is applied a2 DAR http 192 168 0 136 12008 prog maud LIN rist tati Http IP address IP port program name m3u8 e g Http 192 168 0 136 12003 prog1 m3u8 QIWIEIRITIYIURT OIP AISIDIFIGIHIJSIKIL ZIXICIVIBINIM se 27 2 Play the video audio with media player VLC is recommended on phone Tablet Click here Click here Empty Media Library http 192 168 0 136 12003 prog1 m3u8 Open Netv ork Stream 3 Music Albums HLS Protocol gt TV Shows Http IP address IP port program name m3u8 e g Http 192 168 0 136 12003 prog1 m3u8 HTTP Protocol Local Networ Http IP address IP port program name Click Open e g Http 192 168 0 136 12000 prog1 2 Open Network Stream us i ae Network Stream Rtsp IP address IP port program name Sl Downloads e g rtsp 192 168 0 136 12001 prog1 UDP Protocol lE Udp IP address IP port e g udp 192 168 0 137 12002 Cloud Services eM SI ee a eke ee A Settings AS OO GF GS Aw UE UL About VLC for iOS Z X CVBNM com return 28 3 Play the video audio with media player VLC is recommended on computer N ba hs YLC Bedia Player 2 21 z Click Open Network Stream Click Media to unfol
4. DEGING NDS3558A Network Encoder User Manual Thank you for choosing our network encoder Please read this manual carefully to install use and maintain the network encoder in the best conditions of performance Keep this manual for future reference Directory CHAPTER 1 Product nroductions aisi 1 eneral DTek Cela 6 561i eee eee eee eee eens eee ene ene ene Meme eee eens 1 System Connechons Samples 2 Ke Fears areali 2 Technical Specifications eskian E E T aa 2 CHAPTER 2 Safety Instruction and Installations eeeeeeeeeeeeeeeeeeeeeeeees 4 Sary HSE NONS erer ee EEEE EEE aaa 4 WAS CAA ONS sciatica dit scare haces til ctor ede tl setae asad apiananii 4 CHAPTER 3 Operations of TS Creator Software 7 Insalate 7 OPEIS OL CIOT A em ener eee reer eye ee reer reer ERP RE RR PE RARO 7 FileManascmenlsal a a a 9 CHAPTER 5 Operations of Record TS and Play TS through USB Disk 14 CHAPTER 6 Operations of Web GUL lbica allea lbs nia 17 ope 17 Operat OB WE cde ect O RE E E hea E A E A EA 18 Chapter 7 Network Connection and Setup 27 Situation L EANMEEWOrE arr o e iano 27 CHAPTER 1 Product Introductions General Description NDS3558A network encoder is an encoding device for IP broadcasting The signals source could be from STB PC TV and etc It can transfer the live program through the internet LAN and the output signals are to be received by PC phone
5. the system will question the users to save present setting or not If not the LCD will display the current configuration state When the power is connected the LCD will start to initialize the program The LCD menu goes as below chart 10 0 A Up 4 Down gt Enter Menu w Lock Network Encoder 1 Input Lock Encoder 0 Main Menu Status Encoder Interface Video In Status Resolution Vedio Bit Rate Rate Mode H 264 Profile H 264 Level Brightness Contrast Saturation Video Normal Encoder 1 Audio Audio Bitrate Audio Format Encoder Program Info Main Menu Encoder Provider Name Service ID PMT PID PCR PID Video PID Audio PID Main Menu gt USB Device Record TS USB Device Record TS Record Start Advanced Config USB Device Play TS USB Device Disk Usage USB Device Update USB Device Connect device USB Device Remove device Remove device Yes gt No Remove device Yes gt No Network Config IP Address Network Config Subnet Mask Network Config Gateway Network Config Web Port Network Config MAC Address Main Menu Network Config MAC Address XXX XXX XXX XXX 11 Main Menu System Save Config Load SavedCFG Yes gt No Reset all sets Yes gt No System Factory Reset Main Menu gt IP Stream IP Stream Program Name IP Stream HTTP amp RTSP IP Stream UDP IP
6. Insert the USB flash drive with ts videos in NDS3558A and play back the content in an easy way v A single video can be up to 2G in size and multi videos can be played on a loop ts Video Creation Software USB Flash Drive Specifications Required e Standard High Speed 2 0 File System FAT 32 Memory 32G is suggested TS Creator exe Download link http pan baidu com s 1c0vOMYQ Download path EnglishToolTS Creator xxx rar CHAPTER 3 Operations of TS Creator Software NDS3558A network encoder has a function to create TS videos with the software supplied with the product Users can create ts files containing images videos and audios in a simple and intuitive way and play them on a television through NDS3558A s USB port File format supported include Image JPG PNG BMP GIF Video MP4 WMV AVI MPG TS MKV Audio MP3 WAV Installation 1 Download our TS Creator software package on your PC to get the installer and its auxiliary routine 2 Occasionally if your PC hasn t installed Net Frame 2 0 yet double click F NetFx20SP2_x86 exe until complete the installation vh i 3 Double click Setup exe application to install the Creator and generate a desktop shortcut Operations of Creator Double click the Creator shortcut icon pa it will trigger an operation interface like below Creator happy hour avi Audio Saving Di
7. and other mobile terminals Dexin NDS3558A lets you access your IP STB PC or TV anywhere to watch your programs Whether you are in your house or across the globe you ll never miss a game or your favorite show The device supports HDMI YPbPr S Video AV USB input and encodes in MPEG 4 AVC H 264 format after that it gives the IP signal output over UDP multicast Unicast RTP RTSP HTTP HLS The USB port is designed to record and save the encoded video TS in ts files in the USB Keys or Hard Disks and play it back through IP out to increase your content options Control Buttons indicators LCD Window YPbPr S Video AV Q Web manage and Data port USB for Upgrade Video record and playback Power suppl gg ae YPbPr S Video AV to VGA Adapter For video amp audio input System Connection Samples 2 5 a Le outer a Blue Ray Player T n lt P IP STBO 0 Client Router 0 t Optional 3 Various input Mutiple client IRD Optional 1 Optional ROUTER 3558A Network Encoder Optional P ie Optional IP Output over RTP RTSP HTTP HLS Transfer through internet om eer IP Output over UDP Unicast multicast Transfer through LAN Key Features Watch and control your live and recorded TV shows anywhere anytime up to Full HD Support HDMI YPbPr S Video AV USB input Support IP Output over UDP Unicast multicast RTP RTSP HTTP HLS Absolutely no mont
8. the device will not work 3 After update you must reboot device manually Status Current CPU Version 1 01 Current FPGA Version D OF Current Web Version 1 08 CPU ABE Figure 12 25 gt Status Parameters Warning 1 Update firmware software and hardware to get new Encoder function please choose the right firmware to update If you use a wrong file the device may not work FIRMWARE IP Stream 2 Update will keep a long time please do not turn off the power USB otherwise the device will not work NMS 3 After update you must reboot device manually LCD Key Status Current CPU Version 1 01 Password Save Restore Current FPGA Version D O7 Backup Load Current Web Version 1 08 Update FPGA Update CPU Web Update Web ABABA Figure 13 26 Chapter 7 Network Connection and Setup Situation 1 LAN network This is applicable for users in the LAN network like at home STB Network DVD Encoder Camera used as USB Pen Server Steps Wi Fi Mobile Router Terminals Laptop Tablet Phone 1 Connect to STB DVD etc with signal cable or insert USB memory with xx ts files to provide signal source 2 Connect to Wi Fi router Keep the encoder IP and router IP in the same network segment Connect the Wi Fi between the mobile terminals and the router 4 Play the video Audio 1 Play the video audio on phone Tablet under HLS protocol Apple devices can use
9. 3 Browser with HLS plug in 4 Depend on the protocols supported by the STB CHENGDU DEXIN DIGITAL TECHNOLOGY CO LTD No 10 amp No 12 Wuxing 4 road Wuhou District Chengdu China 610045 www dsdvb com http english dsdvb com 31
10. LS is applied no need any Srd party player http 4 192 166 0 136 12003 prog1 m3u8 Data Mode Mode 1 Disable ernpyt packet filter Mode 2 Enable empyt packet filter Program Name Program Name Progl Data Mode o o Data Mode Mode 1 x T TA nee i HTTP Enable v I l HTTP Port 112000 1 65535 i RTSP l l RTSP Enable E l I RTSP Port 12001 1 65535 i UDP l i UDP Dise ____M I IP Address 1224 TIT l UDP Port 12002 11 65535 l I HLS l HLS Disable IN I L___ sot ____ zoo less _ Figure 4 NDS3558A supports IP output over UDP Unicast multicast RTP RTSP HTTP and HLS User can choose the output protocol From the menu on left side of the webpage clicking USB it displays the interface where users can operate USB device Figure 5 20 USB CONFIG Status pela TTT I i Device Status I For reading USB To stop USB device recording q Operation Status gt device status I Le ia i Sii oi playing TS connect remove Il er Record A a SS a 1 Configure TS file I File Name uecord I soi vo r_ amp parameters and click Rasswioni Data Mode Model v I set to start recording Save Restore on J I See ae single file i 2 Click stop to stop Update FPGA ai recording TS and the Update CPU Update Web Play playing section below Pe ___ _ r_r_rr__ co cms 2 z Auto Mode is available to ope
11. SB BitRate 5 500 Mbps NMS Rate Mode CBR v LCD Key H 264 Profile Main Profile v H 264 Level Level 4 1 v Brightness 7 Tyg TTT ez I Password l fi Save Restore Contrast 128 0 255 For contiguring Backup Load l Saturation 128 0 128 I CVBS signal Update FPGA I I Update CPU Hue _ Asi i i 129 lt gt 127 only Update Web Video Normal Auto vi Audio BitRate 64kbps Format MPEG 2 AAC E S Program Info Program name DIVI Provider name DTV Service ID 0x 0102 PMT_Pid 0x 0102 PCR _Pid dx 0103 Video _Pid Ox 0100 Audio_Pid 0x 0101 Max Rate 6 Mbps Figure 3 Parameters IP Stream Click IP Stream from the left menu it will display the screen as Figure 4 where to configure the IP Output After setting the parameters click Apply to save the setting 19 Network Encoder 2015 07 21 17 20 23 EN PX Exit Status Parameters Encoder IP Stream USE NMS LCD Key Password Save Restore Backup Load Update FPGA Update CPU Update eb Parameters USB IP STREAM Setup Instruction Below links is illustrated based on factory default config It subject to actual setting when use HTTP http 4 192 166 0 136 12000 prog1 RTSP rtsp 4 192 166 0 136 12001 prog1 UDP 1 Unicast Suppose the target ip is 192 168 0 137 udp 4 192 168 0 137 12002 2 Multicast udp 4 224 2 2 22 12002 HLS Apple device can use Safari browser when H
12. Stream HLS 1 Network Encoder Input Lock Encoder Rate x xxMbps Valid Rate x xxMbps Max Rate x xxMbps 2 Alarm Status For example if the signal cable disconnected it will display Input UnLock under this menu 3 Uptime It displays the working time duration of the device It times upon power on 4 Video Parameters User can enter the items respectively to set video parameters Interface select a right interface type from the options provided The device then can automatically search the signal and starts to encode Resolution signal source resolution read only Video Bit rate adjust in range of 1 000 19 000 Mbps Rate Mode this unit user can choose CBR or VBR User can also adjust values of rest items H 264 profile H 264 level Brightness 0 128 amp Contrast 0 255 amp Saturation 0 128 Hue 128 127 Video Normal 5 Audio Bit rate Select audio bit rate from the options provided 64 96 128 192 256 320 384kbps Audio Format Select audio format among MPEG2 MPEG2 AAC and MPEG4 AAC 12 gt NOTE If you are to apply HLS as the output stream protocol you need choose MPEG2 AAC here as HLS supports only MPEG2 AAC Audio format 6 Program Information User can enter the sub menus to edit the Program Name Provider Name Service ID and PIDs of PMT PCR Video and Audio 7 12 Please refer to Chapter 5 for details 13 IP Address To configure IP address here 14 Subnet Mask To configure su
13. arable damage to the device and the invalidation of the warranty Therefore Do not replace power supply with a voltage greater than 12V DC Do not connect the device to the power if the power cord is damaged Do not plug the device into mains supply until all cables have been connected correctly Do not cut the cord Avoid placing the device next to central heating components and in areas of high humidity Do not cover the device with elements that obstruct the ventilation slots If the network encoder has been kept in cold conditions for a long time keep it in a warm room minimum 2 hours before plugging into the mains Mount the device in vertical position with the connectors located on the top side When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutes may result in fire electric shock or other hazards Safety check Upon completion of any service or repairs to this device ask the service technician to perform safety checks to determine that the device is in proper condition Installations y RISK OF damage to the unit Mechanically handling the unit may result in damage Do not connect the unit to the power supply before or during assembly Connect the unit as below instructed Y NO HOT PLUG 1 Mount and tighten the screws and plugs to secure the unit to the wa
14. ay mode for the ts files as needed before playing the ts file and specify a video under Play one Play one loop mode and press Enter button to start play While under Play all Play all loop mode it automatically plays files from first to end 2 Advanced Config Auto Mode is for saving the play mode for the device When the auto mode is enabled the device will automatically apply the play mode set before the power cut off and output ts files stored in the USB device through RF While the auto mode is off NDS3558A will play the encoded TS through RF when the power is connected 4 Disk Usage Main Menu USB Device Disk Usage USB Device Disk Usage XX XXG x xxG Users can enter this menu to view the USB disk s capacity left 5 Update Main Menu gt USB Device Updatee USB Device Update gt PFGA Choose one item to be updated and press Enter to confirm Keep the update file stored in the USB device in dxf format 15 6 Connect Device Main Menu USB Device USB Device Connect device Press Enter key to re connect the USB disk 7 Remove Device USB Device Remove device Press Enter key to safely remove the USB disk NDS3558A will then automatically resume encoding process and playing the program input from the encoder module 16 CHAPTER 6 Operations of Web GUI In addition to using front buttons to control the network encoder and USB device users can also perform the same operation in an easi
15. bnet mask here 15 Gateway To configure gateway here 16 Web Port To configure web port here 17 MAC Address To view MAC address here 18 Save Config Yes No to save give up the adjustment of setting 19 Load Saved CFG Yes No to load not to load the saved configuration 20 Factory reset Yes No choose not choose the factory s default configuration 21 LCD Time out Set the time limit that LCD will light off 22 Product ID User can view the serial number of this device It is read only and unique 23 Version It displays the version information of this device 24 Program name Set the program name of the IP output stream 25 27 HTTP RTSP UDP HLS User can choose the output protocol and output port at this interface 13 CHAPTER 5 Operations of Record TS and Play TS through USB Disk The NDS3558A network encoder has functions of 1 ts Video Creation See Chapter 3 2 TS Record and Save Record more select gt Sin M File Record TS 8 Loop Record Record TS Advanced Config File name File size Data Mode Main Menu USB Device USB Device Record TS 1 Connect the signal source enter Record Start and then choose one record mode to start recording the encoded TS And press UP key and then Enter key to stop recording There are 3 record modes provided Single file For example when the file size is set as 1000M and the ts is recorded up to 1000M it automati
16. cally stops recording TS Segment file For example when the file size is set as 1000M and the ts is recorded up to 1000M it automatically saves the files and continues to record TS and save it to next file until the USB memory is full Loop record It automatically saves the files and continues to record TS and save it to next file When the USB memory is full it replaces the previous file 2 Advanced Config File Name Users can enter this menu to edit name for the ts files to be recorded For example if users name it Record it will give name to the saved ts files Record 001 ts Record 002 ts Record 00N ts File Size users can set the file size for the ts to be recorded A single file can be maximum 2048M in size Data Mode There are 3 data modes 14 Mode 1 The ts files will be saved in 188 byte packages with null packet embedded Mode 2 The ts files will be saved in 188 byte packages with null packet filtered However such ts files cannot be normally played with NDS3558A but can be played on PC with some media player such as VLC Mode 3 The ts files will be saved in 204 byte packages with null packet filtered 3 TS Playback Play mode select File select v v Main Menu USB Device Play TS gt Play one Lo xxxlis gt USB Device Play TS Play Start 0 a loop mes gt ay a mmm Playallloop L On Off 1 Play Start User can select a pl
17. d pull down menu A Open Media D File P Disc fi Network IS Capture Device Network Protocol Please enter a network URL 1 Whe sp 192 168 0 138 12003 pr og au HLS Protocol Http IP address IP port program name m3u8 e g Http 192 168 0 136 12003 prog1 m3u8 HTTP Protocol Http IP address IP port program name e g Http 192 168 0 136 12000 prog1 RTSP Protocol Rtsp IP address IP port program name e g rtsp 192 168 0 136 12001 prog1 UDP Protocol c Udp IP address IP port e g Udp 192 168 0 137 12002 To play program Situation 2 WAN network This is applicable for users far away from home and terminals need access to internet to watch programs STB Network Wi Fi Mobile Terminals DVD Encoder Router Laptop Tablet Camera used as if Phone USB Server needed 29 Steps I Connect to STB DVD etc with signal cable or insert USB memory with xx ts files to provide signal source Connect to router Keep the encoder IP and router IP in the same network segment Connect the router and the manage PC by entering the router IP in browser like below Keep the PC IP in the same network segment with encoder IP and router IP 500A v1 2 17708 O poate eel eee ane OMe O 68 mit OMZSFLP Heit Ape ROME OR Bit EEFIMACHitt Netcore Co LTD ine Al Rights Reserved BABASIRPRI RAMON 4 Go to DMZ h
18. er way with the web Brower in the PC Personal Computer Login The default IP address of this device is 192 168 0 136 We can modify the IP through the front panel Connect the PC and the network encoder with a net cable and use ping command to confirm they are on the same network segment I G the PC IP address is 192 168 99 252 we then change the device IP to 192 168 99 xxx xxx can be 1 to 254 except 252 to avoid IP conflict Use web browser to connect the device with PC by inputting the device s IP address in the browser s address bar and press Enter It will display the Login interface as Figure 1 Input the Username and Password Both the default Username and Password are admin and then click OK to start the device setting Windows Security The server 192 168 0 136 at Web Server Authentication requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection ser name Password Remember my credentials Cancel Figure 1 17 Operation Summary When we confirm the login it displays the WELCOME interface as Figure 2 where users can have an overview of the device s system information and working status I Network Encoder welcome to use Vel 5 07 10 10 08 5fEN 4132 Exit I Encoder l IP Stream I USB I NMS LCD Key i Password l Save Res
19. ge it like as 8001 you can visit Password the manage web only use IP address and port liks as Save Restore http 192 168 0 1 8001 This function will work after device reboot Backup Load Update FPGA Input this address in ee ins IP Address 192 168 0 136 gt the browser to connect Subnet Mask 255 255 255 0 the device and PC Gateway 192 168 0 1 Web Manage Port 80 MAC Address 02 A1 AZ A3 A4 A5 22 Figure 6 Parameters LCD Key From the menu on left side of the webpage clicking LCD Key it displays the interface where users can set the time out for the LCD Figure 7 Network Encoder Aanagement 2015 07 10 10 21 3 EN X Exit Status LCD Encoder LCD Time Out 130 Second IP Stream USE ne LCD Key LEDIKEY CONFIGURATION Figure 7 System Password From the menu on left side of the webpage clicking Password it will display the screen as Figure 9 where to set the login account and password for the web NMS Figure 8 PASSWORD Status Modify the login name and password to make the device safely If success you can save the config and reboot If forget the name or Encoder password you can reset it by keyboard The default login name and IP St password is admin Also please note the capital character and LEAN lowercase character USB NMS LCD Key Current UserName admin Current Password ia ee Password New Password Save Restore Confirm New Passw
20. hly fees Easy to connect and set up HLS Protocol supporting 6 10 Apple terminals simultaneously running as per different resolution and bit rate setting USB port for TS recording and playing back increase signal source option Technical Specifications 1920x1080_60p 1920x1080_50p 1920x1080_601 1920x1080_501 Resolution 1280x720_60p 1280x720_50p Video 720x576_501 720x480_601 Encoder MPEG 4 AVC H 264 HDMI input Section 1 Mbps 19Mbps MPEGI Layer I MPEG2 AAC Encoding MPEG4 AAC Audio 64 96 128 192 256 320 384kbps 2 64 96 128 192 256 320 Cee etereo NN Stream out out IPout over UDP IP out over UDP Unicast multicast RTP RTSP HTTP HLS RI45 1000M RTP RTSP HTTP HLS RJ45 1000M LCD control buttons System Chinese English control interface Upgrade USB Web server General Power supply DC12V CVBS amp S Video 720x576_50i PAL 720x480_601 NTSC Video Resolution YPbPr YPbPr CVBS S Video 1920 1080_ 601 1920 1080_ 501 with an adapter to 1280 720_60p 1280 720_50P MPEGI Layer II MPEG2 AAC Encoding MPEG4 AAC CHAPTER 2 Safety Instruction and Installations Safety Instructions WARNING Hot plug is not allowed since it may cause system halted To prevent fire or electrical shock do not expose the device to rain or moisture x The network encoder is powered with a voltage of 12V DC The power supply voltage must not exceed the recommended voltage which otherwise may cause irrep
21. ion before load file if you use a wrong file the save Restore device may not work Backup Load 2 Please do not turn off the power while file loading otherwise Update FPGA the device will not work Update CPU Update Web ABER Figure 10 System Update FPGA CPU Web From the menu on left side of the webpage clicking Update it will display the screen 24 as Figure 11 13 where to update the corresponding part for the device status Parameters Encoder IP Strearn USB NMS LCD KEey Password Save Restore Backup Load Update FPGA Update CPU Update Web FIRMWARE Warning 1 Update firmware software and hardware to get new function please choose the right firmware to update If you use a wrong file the device may not work 2 Update will keep a long time please do not turn off the power otherwise the device will not work 3 After update you must reboot device manually Status Current CPU Version 1 01 Current FPGA Version D OF Current Web Version 1 08 FPGA AUPE Figure 11 Status Parameters Encoder IP Stream USB NMS LCD Key Password Save Restore Backup Load Update FPGA Update CPU Update Web gt FIRMWARE Warning 1 Update firmware software and hardware to get new function please choose the right firmware to update If you use a wrong file the device may not work 2 Update will keep a long time please do not turn off the power otherwise
22. ll Left 10 cm of free space around from each unit 2 Connect the signal input in the respective connectors The signal source can be from a surveillance monitor DVD set top box CCTV and etc 3 Incase of connecting to a wired network connect the t encoder Ethernet port and 3 sigg G v gt SAG i a e terminal s i i H i A rt Ethernet port O C r sk wiht ethernet c A M OVD ste Tarainala pona cable 4 Incase of connecting wireless network following Step 2 connect the encoder Ethernet port and router port with Ethernet cable 5 Power supply connection a Connect the earth cable b Connect the power plug to the unit mains connector c Connect the power plug to the mains socket USB Recoder amp Player SS a TS Recorder and Save NDS3558A can encode the source video to ts files and save them through the USB flash drive WwW e Connect the signal source to NDS3558A and start encoding process v Users can also create ts videos e Start the record process and save the ao containing pictures videos and music TS generated to the USB flash drive with our creator software on a PC and n save them into the USB flash drive e Drag the files to Creator application Formats supported include Z Image JPG PNG BMP GIF Audio MP3 WAV Video WMV MPG MP4 TS AVI v Start the conversion process to generate ts videos TS Playback e
23. ord Backup Load Update FPGA Update CPU Update Web Figure 8 System Save Restore From the menu on left side of the webpage clicking Save Restore it will display the 23 screen as Figure 9 where to save or restore your configurations Status When you change the parameter you should save configuration otherwise the new configuration will lost after reboot SAVE CONFIGURATION Encoder IP Stream oe NMS RESTORE CONFIGURATION LCDiKey Load latest saved configuration after click the Restore then please click the Save config button otherwise the Restore parameter will Password lost after reboot Save Restore Backup Load Upedte eer FACTORY SET Update CPU Update Web Set all configuration back to default after click the Factory Set then please click the Save config button otherwise the default parameter will lost after reboot Figure 9 System Backup Load From the menu on left side of the webpage clicking Backup Load it will display the screen as Figure 10 where to backup or load your configurations BACKUP CONFIGURATION Status Backup current configuration to the local file we suggest do this before set the configuration or update firmware Encoder IP Stream USB NMS LOAD CONFIGURATION LCD Key Load the backup file to restore your configuration Warning Password 1 New configuration will replace the old one please backup current configurat
24. ost enable DMZ and enter the encoder IP like below Different router may have different interface and menu instruction this picture is just for reference DMZ KE BR O jH oo isa cise EE mh RAF ER Save and Appl ii Find out the Internet IP address It must be a Static IP consult your operator if you don t know it that allocated to your account by your local operator and operate terminal device as below For example Assume the internet IP in your home is 222 208 125 226 1 Enable the internet or Wi Fi on your Laptop Tablet Phone 2 Play the video Audio the steps are the same as LAN network only the IP address is not the same ace en WAN Allocated to your account oo Http IP address IP port progr am name m3u8 by your local operator e g Http 222 208 125 226 12003 prog m3u8 2 IP address as Me IP address network encoder IP 30 HTTP Protocol Http IP address IP port program name e g Http 222 208 125 226 12000 prog 1 RTSP Protocol Rtsp IP address IP port program name e g Rtsp 222 208 125 226 12001 prog1 UDP Protocol Udp IP address IP port e g Udp 222 208 125 226 12002 Here s a guide to what needed in the receiving terminals when watch through NDS3558A network encoder Mobile Terminals IP STB PC 10S upp 2 2 4 tor Persp 2 2 a tr Twp 2 2 14 tnd 1 Browser 2 3rd Party Media Player like VLC Buzz Player etc
25. prompts The operation completed normally JClick this button to stop the transformation before the operation completed EE After finishing the transform operation users can click this button to play the generated TS video File Management After finishing the transformation users can find out the videos files generated according the Saving Directory For example we save the video in D ABC so we can find it in Disk D Folder ABC Management 1 Three files will be generated if the Null Packet has been filtered E FinalOutput ts TS video for preview through the Creator interface by clicking Play button E FinalOutput_204 0 ts fa FinalOvtput_204 0 tsinfo gt TS video and information files Users need to save the two files together in the USB memory and then NDS3558A can read them and play the video 2 Two files will be generated if the Null Packet has not been filtered Ej FinalOutput ts TS video for preview through the Creator interface by clicking Play button rene DI video Users need to save it in the USB memory and then NDS3558A can read it and play the video Remarks All the file names are automatically generated Rename the files before creating a new video to avoid covering the previous files If you rename FinalOutput 204 0 ts or FinalOutput 204 0 tsinfo always keep the names the same Extension excluded and then NDS3558A can read them and play the video
26. rate 1 Configure TS playing lt Operation play one v i parameters and click set to start Ces pecoe ats Sl I playing TS files sat 2 Click stop to stop playing TS Lee e 4 and the recording section above is available to operate Figure 5 NOTE It is necessary to connect USB device and signal source and activate encoding to operate TS recording NOTE It is necessary to connect USB device when operate TS playing Detailed Explanation There are 3 record modes provided s Single file For example when the file size is set as 1000M and the ts is recorded up to 1000M it automatically stops recording TS Segment file For example when the file size is set as 1000M and the ts is recorded up to 1000M it automatically saves the files and continues to record TS and save it to next file until the USB memory is full Loop record It automatically saves the files and continues to record TS and save it to next file When the USB memory is full it replaces the previous file Advanced Config File Name Users can enter this menu to edit name for the ts files to be recorded For example if users name it Record it will give name to the saved ts files Record 001 ts Record 002 ts Record 00N ts File Size users can set the file size for the ts to be recorded A single file can be maximum 2G in size Data Mode There are 3 data modes 21
27. rectory Picture Duration Out Put Size Rate EncodeF ormat Null Packet Filter File Separated Size Em Lu Flower 1 bmp Flower 2 JPG lalala mp3 DB ABC 1 gt Second s 1920 1080 v 10 Mpbs x 264 MPEG2 Yes O No 2 0 gt G Bytes na Starting Sc Add Remove Remove ALL Audis lalala mp Saving Directory D ABC Ficture Duration playing the video Out Put Size Rate 10 Click to add Images and videos Click to adjust the order of Images videos Click to delete the Images videos Click to add audios Browse Click to set a save path for the TS video to be created i Endi To set time duration for every picture when 192041080 MT set the resolution for the output video Mes The video is transformed based on VBR Variable Bit Rate The number set here represents the highest bit rate for the output video and bit rate will varies under the number SITI H 284 MPEG2 Users can select H 264 encode format here NOTE If you are to apply HLS as the output stream protocol you need choose H 264 here as HLS supports only H 264 Video format Null Packet Filter Yes He Users can filter the null packet to boost the video s effect bit rate STA SEE Bese 4 Bytes A single video can be maximum 2 0 GB in size NDS3558A cannot play a video bigger than 2GB After setting all the parameters click to start the transformation Click OK when it
28. tore l Backup Load l Update FPGA i Update CPU Update Web User can click any item here to enter the corresponding interface to check information or set the parameters Status Input Rate Alarm DEVICE INFORMATION Software Version I Hardware Version l Web Version l l Product ID I Uptime nterface I Video Lock encoder rate valid rate max rate l FPGA Lost l Encoder Error I TCP Error Encoder Lost TS Lost I Input UnLock USB Play Error I TS Overflow 1 01 I l D 07 l 1 08 r gt System information 010501020140514 0 Days 13 55 11 Input information and Locked lo l l encoding working status Locked 5 910528 Mbps 6 057984 Mbps 6 141952 Mbps I Alarm Area Green light l indicates the corresponding item is in normal status Otherwise the light is red Parameters Encoder Figure 2 From the menu on left side of the webpage clicking Encoder it displays the interface where users can configure the encoding parameters for the input video audio Figure 3 18 Network Encoder 2 use Web Manageme 2015 07 10 10 09 5fEN PX Exit A ENCODER CONFIG n Select an interface Status i pce according to the signal sia DE source user connects Status mi and intends to encode ncoder Resolution IP Stream U
Download Pdf Manuals
Related Search