LED BLINDER WHITE - user manual - ENGLISH
Contents
1. EN DISPOSAL OF THE DEVICE Dispose ofthe unit and used batteries in an environment friendly manner according to your country regulations FR D CLASSER L APPAREIL D barrassez vous de l appareil et des piles usag es de mani re cologique conform ment aux dispositions l gales de votre pays NL VERWIJDEREN VAN HET APPARAAT Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke manier conform de in uw land geldende voorschriften DU ENTSORGUNG DES GER TS Entsorgen Sie das Ger t und die Batterien auf umweltfreundliche Art und Weise gem den Vorschriften Ihres Landes ES DESHACERSE DEL APARATO Reciclar el aparato y pilas usadas de forma ecologica conforme a las disposiciones legales de su pais PT COMO DESFAZER SE DA UNIDADE Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em conformidade com as normas vigentes no seu pais ENGLISH OPERATION MANUAL OPERATION MANUAL Thank you for buying this Briteq product To take full advantage of all possibilities and for your own safety please read these operating instructions very carefully before you start using this unit FEATURES This unit is radio interference suppressed This product meets the requirements of the current European and national guidelines Conformity has been established and the relevant statements and documents have been deposited by the manufacturer This device was designed to produce decorative2. ENGLISH OPERATION MANUAL OPERATE THE UNIT BY CA8 HAND CONTROLLER When used in standalone or master slave mode we strongly advise you to use the CA 8 Wired easy controller connect the controller to the jack input of the first unit master Now you can control all the connected units STANDBY BUTTON Press this button to start stop blackout mode on all connected units MODE FUNCTION BUTTONS With the MODE button you can select 3 different modes e The LED is off with the FUNCTION button you can select different strobe modes like sound strobe e The LED is blinking slowly with the FUNCTION button you can select different shows e The LED is blinking fast with the FUNCTION button you can select different speeds MAINTENANCE e Make sure the area below the installation place is free from unwanted persons during servicing e Switch off the unit unplug the mains cable and wait until the unit has been cooled down During inspection the following points should be checked e All installing screws and any of its parts should be tightly fastened and may not be corroded e Housings fixations and installations spots ceiling truss suspensions should be free from deformation e When an optical lens is visibly damaged due to cracks or deep scratches it must be replaced e The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected To protect the device from o
3. fF controller it has to decode In the next section you will l DES Bot A controllable ninctions DMX learn how to set the DMX addresses TO NEXT e For the DMxX controller the master and his slaves can gt DMX UNIT now be considered as 1 virtual effect that needs a start L Brennen 27 address so it can be controlled as any other DMX unit in TO MORE HOW TO SET THE RIGHT START ADDRESS the DMX chain see DMX Address in the chapter Main C SLAVES Refer to the previous chapter DMX 512 address setting to learn how to set the starting address on this unit The starting address of each unit is very important Unfortunately it is impossible to tell you in this user manual which starting addresses you have to set because this completely depends on the selected channel mode and on the controller you will use So please refer to the user manual of your DMX controller to find out which starting addresses you must set Menu to see how you can set the DMX start address e Make sure that all units are connected to the mains e Set the DMX controller according to the DMX chart below e Done Remark in order to work well to the rhythm of the music make sure that the option Sound State on the master is set to On see previous chapter BRITEQ 7 10 LED BLINDER WHITE BRITEQ 8 10 LED BLINDER WHITE ENGLISH OPERATION MANUAL DMX CONFIGURATIONS Apart from the DMX Master slave mode 4MSL there are also 4 other DMX ch
4. signal Pi o opo Ee Pin3 Positive signal Pins4 5 not used 100V 240V e To prevent strange behavior of the light effects due to interferences you must use a 900 to 1200 terminator at the end of the chain Never use Y splitter cables this simply won t work e Make sure that all units are connected to the mains Gees DMX SPLITTER to isolate the master slave line from the main DMX line see drawing e Connect 2 to maximum 999 units together using good EE quality balanced microphone cables The first unit in the MASTER chain will act as the master the other units will act DMX automatically as slaves ee vd Ece BUNDER H e Even BLINDER e Set the master to 4MSL channel mode see previous 3 a E o Ee mees e Each light effect in the chain needs to have its proper DMX chapter Check the DMX chart below to see the SE IRIRA SE
5. the other units WASTER i will act automatically as slaves n 68 97 Chase 3 e Make sure that all units are connected to the mains DMX 38 67 Chase 2 e Done GHEE a ah Eten suner 0 37 Chase 1 Remark You can connect a CA 8 remote controller to the SLAVE 1 0 7 Full On 0 master unit if you want to have more control over the master slave operation DMX Remarke if there s no output please make sure to set the REESEN Electrical installation in DMX mode iS EE fo NO SLAVE 2 l e The DMX protocol is a widely used high speed signal to control intelligent light equipment You need to daisy chain your DMX controller and all the connected Remark3 please note that linking of the mains power input is limited to 10 units units with a good quality balanced cable SU ohm Cont aa e Both XLR 3pin and XLR 5pin connectors are used however XLR 3pin is more S resistor Electrical installation for two or more units in 4MSL DMX master slave popular because these cables are compatible with balanced audio cables i units wi w y iz W RE Ee eee EE e eventually working to the rhythm of the beat but you can still CLSA huis L l MAIN j a ane E eee 100V 240V control some functions on the master by 4 DMX channels DMX LINE e EC EE Ka e To assure proper operation you need an optional Mini Pim layout ALR Sail Pint ONE rind S Negative
6. 10 LED BLINDER WHITE ENGLISH OPERATION MANUAL e Before rigging make sure that the installation area can hold a minimum point load of 10times the device s weight e Always use a certified safety cable that can hold 12times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails e The device should be well fixed a free swinging mounting is dangerous and may not be considered e Don t cover any ventilation openings as this may result in overheating e The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be inspected every year by a skilled person to be sure that safety is still optimal SETUP MENU Before you can operate the unit properly you should set the right configuration via the setup menu e To select any of the functions press 0 the MENU button up to when the DMX i Address required one is shown on the display or use the DOWN and UP buttons to browse the menu wech 1Chan e Select the function with the ENTER Sonne SE button the display blinks Mode e Use DOWN and UP buttons to change 2chan the mode Amount 001 999 SP 0 10 10 Eerst i SP 255 I i e Once the required mode is selected press the ENTER button to confirm To
7. Gees go back to the main menu without any Mode change press the MENU button shortly The main menu is shown in the chart zs SP 0 DMX Address reaa Used to set the start address in a DMX setup Off e Press the MENU button until DMX MENU o i Address is shown on the display e Press the ENTER button the display 100 starts blinking Black No e Use DOWN and UP buttons to change the DMX512 address Back On e Once the correct address shows on the display press the ENTER button to Auto save it A x uto To go back to the main menu without any Fan change press the MENU button shortly High If you want to go back to normal running mode press the MENU button for about 2 seconds Fixture Channel mode Firmware Used to set the desired channel setup mode e Press the MENU button until Channel mode is shown on the display e Press the ENTER button the display starts blinking e Use DOWN and UP buttons to choose 1Chan 12Chan 10Chan 2Chan or 4MSL mode e Once the desired channel setup mode shows on the display press the ENTER button to save it To go back to the main menu without any change press the MENU button shortly If you want to go back to normal running mode press the MENU button for about 2 seconds BRITEQ 4 10 LED BLINDER WHITE ENGLISH OPERATION MANUAL Show Mode Used to choose the Show mode when used in standalone or master slave mode e Press the MENU button until Show Mode is
8. LED BLINDER WHITE Operation Manual Other languages FR NL DU ES PT can be downloaded from WWW BRITEQ LIGHTING COM WWW BRITEQ LIGHTING COM C Copyright 2010 by BEGLEC Ny Brile t Hofveld 2C B1702 Groot Bijgaarden Belgium Reproduction or publication of the content in any manner without express permission of the publisher is prohibited Version 1 0 LIGHT RESEARCH DANGER GEVAAR GEFAHR PELIGRO PERIGO WARNING DANGER never expose the lens to direct sunlight even for a short period This may damage the light effect or even cause fire ATTENTION DANGER n exposez jamais la lentille directement aux rayons de soleil m me pendant un bref instant Ceci peut endommager l int rieur de l appareil ou m me causer un incendie OPGELET GEVAAR stel de lens nooit bloot aan direct zonlicht zelfs gedurende een korte periode Dit kan het toestel beschadigen en zelfs brand veroorzaken WARNUNG GEFAHR Setzen sie die Linse niemals direkter Sonneneinstrahlung aus auch nicht f r eine kurze Zeit Die direkte Sonneneinstrahlung kann das Ger t zerst ren oder zum brennen bringen ADVERTENCIA PELIGRO jnunca exponga la lente a la luz solar directa a n durante un per odo corto jEsto puede da ar el efecto de luz o incluso causar el fuego AVISO PERIGO Nunca exponha as lentes directamente luz solar mesmo que por pouco tempo Isto pode danificar o efeito luminoso ou mesmo provocar um inc ndio
9. according to the regulations for electrical and mechanical safety in your country 4MSL mode Electrical installation for 1 standalone unit e Just insert the mains cable The unit starts working immediately in stand alone mode Remark You can connect a CA 8 remote controller to the unit if you want to have more control Refer to how to operate the unit to learn how to do this Rand 255p 100 SCH ra ANGOM 5492955 248 255 Open Remarkz2 if there s no output please make sure to set the unit in master mode and set the blackout mode 248 255 Chase Active to NO and Sound State to On see previous chapter 247 F Fast Fast 218 247 Chase 8 188 217 Chase 7 Ss 158 187 Chase 6 Electrical installation for two or more units in master slave In this mode the units will show a synchronized show working to the rhythm of the beat e Connect 2 to maximum 999 units together using good 100V 240V 128 157 Chase 5 quality balanced microphone cables The first unit in the GREE a l ee E Eemer 77 SET VS chain will automatically act as the master
10. al programs 7 DMX INPUTS connect this input to the previous unit in the DMX chain or directly to the DMX controller 8 DMX INPUTS connect this input to the next unit in the DMX chain 9 REMOTE CONTROL connector used to connect the CA 8 hand controller 10 SECURITY EYEBOLT used to secure the unit with an optional safety cable 11 MAINS POWER IN OUT IEC in outputs use the supplied IEC cable to connect the projector to the mains You can also daisy chain up to 10 units using the optional IEC extension cables available under order code 4151 L 1m order code 4152 L 5m 12 FUSE HOLDER always exchange a broken fuse with the same 20x5mm 6 3A type OVERHEAD RIGGING e Important The installation must be carried out by qualified service personal only Improper installation can result in serious injuries and or damage to property Overhead rigging requires extensive experience Working load limits should be respected certified installation materials should be used the installed device should be inspected regularly for safety e Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing e Locate the fixture in a well ventilated spot far away from any flammable materials and or liquids The fixture must be fixed at least 50cm from surrounding walls e The device should be installed out of reach of people and outside areas where persons may walk by or be seated BRITEQ 3
11. annel modes that you can choose of see chapter setup menu option channel mode The desired DMX channel mode depends on how much control you need 1channel and 2channel modes are simple channel modes with limited DMX control 1 Channel mode 2 Channel mode Dimmer Strobe 248 255 On 299 248 255 0pen Random EES 240 247 Strobe 201 247 s 232 239 Open Slow close 190 231 Fast open 182 189 Open S Glow open SES Fast close 132 139 Open SS 8 131 4 Blackout Blackout 100 s 191 200 With 10channel and 12channel modes channel modes you have full DMX control over all 10 clusters 10 Channel mode CH1 cH2 cus cua chs cHe cH7 chs omg ong Semer Dimmer Dimmers Dimmers Dimmer Dimmers Dimmer Dimmer immer Dimmert0 255 r 100 255 p 100 255 r 100 255 p 100 255 p 100 255 p 100 255 r 100 255 p 100 255 p 100 255 100 12 Channel mode CH1 CH2 CH7 CH8 CH9 enn CH11 CH12 Dinner Dinner Dimmer Dimmer Dinner Bimmer Dine Dimmer Dinner Sec WASTER gece 255 r 100 255 p 100 255 p 100 255 p 100 255 p 100 255 p 100 255 p 100 255 p 100 255 p 100 255p 100 255p 100 248 255f0pen andom 240 247 OM 232 239 Open Slow close 190 231 Fast open 182 189 Open Slow open 140 181 Fast close 132 139 Open Sos 8 131 Ki 0 7 Blackout BRITEQ 9 10 LED BLINDER WHITE
12. asked which playback speed you want for the show choose from 0 to 255 Press ZENTER to confirm Note that this setting is only relevant while used without any controller you can change the speed using the menu buttons on the master e 5 10 select this option when the unit is used in a master slave setup with several units placed in a 5x10 matrix 5 units mounted on top of each other using the optional matrix bracket Press lt ENTER gt to confirm e You will be asked which preprogrammed show you want to use choose from 3 1 to 3 8 Press ZENTER to confirm Note that this setting is only relevant while used without any controller you can change the speed using the menu buttons on the master e You will be asked which playback speed you want for the show choose from 0 to 255 Press ZENTER to confirm Note that this setting is only relevant while used without any controller you can change the speed using the menu buttons on the master To go back to the main menu without any change press the MENU button shortly If you want to go back to normal running mode press the MENU button for about 2 seconds Sound State The unit works to rhythm of the beat when used in standalone or master slave mode e Press the MENU button until Sound State is shown on the display e Press the ENTER button the display starts blinking e Use DOWN and UP button to select On or Off mode e Once the mode is selected press the ENTER button save i
13. effect lighting and is used in light show systems No more expensive halogen lamps with extremely short lifetime this powerful LED Blinder is the future Equipped with 40 high power 1Watt LEDs distributed over 10 independent clusters Each LED cluster is fully controllable by DMX for endless possibilities Different preprogrammed shows random audio controlled falling star line chases fading effects 10x10 matrix programs for 10units Different operation modes e DMX 1ch 1fader for combined dimmer sound active strobe and full on function on all clusters e DMX 2ch dimmer different strobe functions on all clusters e DMX 4MSL DMX master slave choose from a selection of internal chases chase strobe speed amp dim e DMX 10ch dimmer control for individual clusters e DMX 12ch dimmer control for individual clusters master strobe function master dimmer e Standalone with optional hand controller Perfect for use in TV studios thanks to the 400Hz dimmer electronics Very narrow 15 beam angle for very focused beams Very low power consumption only 57W at full output money saving Heavy duty bracket can be used as floor stand and easy truss mounting An optional matrix bracket can be used to mount 10 units in a 10x10 matrix Easy software updates via special software upgrade unit Alphanumeric LCD display for easy menu navigation BEFORE USE Before you start using this unit please check if there s no transpor
14. he MENU button shortly If you want to go back to normal running mode press the MENU button for about 2 seconds Temperature inside the unit Used to show the temperature inside the unit e Press the MENU button until the display shows Fixture Temp e Press the ENTER button to show the internal temperature of the unit on the display e To go back to the functions press the MENU button again If you want to go back to normal running mode press the MENU button for about 2 seconds Fixture Hours Used to show the number of working hours of the unit e Press the MENU button until the display shows Fixture Time e Press the ENTER button to show the number of working hours in the display e To go back to the functions press the MENU button If you want to go back to normal running mode press the MENU button for about 2 seconds Software version Used to show the software version that is installed in the unit e Press the MENU button until the display shows Firmware Version e Press the ENTER button to show the software version on the display e To go back to the functions press the MENU button If you want to go back to normal running mode press the MENU button for about 2 seconds BRITEQ 6 10 LED BLINDER WHITE ENGLISH OPERATION MANUAL ENGLISH OPERATION MANUAL DMX Chart for 4MSL working mode INSTALLATION OPERATION A Important The electrical installation should be carried out by qualified personal only
15. here are no user serviceable parts inside Never repair a fuse or bypass the fuse holder Always replace a damaged fuse with a fuse of the same type and electrical specifications LED BLINDER WHITE ENGLISH OPERATION MANUAL In the event of serious operating problems stop using the fixture and contact your dealer immediately The housing and the lenses must be replaced if they are visibly damaged Please use the original packing when the device is to be transported Due to safety reasons it is prohibited to make unauthorized modifications to the unit Important Never look directly into the light source Don t use the effect in the presence of persons suffering from epilepsy DESCRIPTION LED BLINDER GE WHITE 1 COOLING FANS these fans are temperature controlled so most of the time they will NOT work this is normal Make sure the fans are always clean and never cover the holes this will result in possible overheating 2 BRACKET used to hang the projector in truss optional truss clamp needed Also used as heavy duty floor stand for use on stage 3 DISPLAY shows the various menus and the selected functions 4 LEDS DMX DMX input present MASTER Master mode SLAVE SOUND 5 BUTTONS MENU To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions 6 MICROPHONE used to control the music activated intern
16. klight on display is always lit Backlight off display is dark when not used e Press the MENU button until the display shows Back Light e Press the ENTER button the display starts blinking e Use DOWN and UP buttons to select On display always lit or Off display dark when not used e Once the mode is selected press the ENTER button to save it To go back to the main menu without any change press the MENU button shortly If you want to go back to normal running mode press the MENU button for about 2 seconds Auto Test Used to activate the internal self test program which checks all possibilities of the unit e Press the MENU button until the display shows Auto Test e Press the ENTER button to start the internal self test program e To go back to the functions press the MENU button If you want to go back to normal running mode press the MENU button for about 2 seconds Fan Speed Auto Speed Fans are temperature controlled preferred mode most of the time the unit is quiet High Speed Fans always turn at high speed only to be used under heavy temperature conditions e Press the MENU button until the display shows Fan Speed e Press the ENTER button the display starts blinking Auto or High Speed e Use DOWN and UP buttons to select Auto or High e Once the mode is selected press the ENTER button to save it To go back to the main menu without any change press t
17. showing on the display e Press the ENTER button the display starts blinking e Use DOWN and UP buttons to select one of the available shows e Line select this option when the unit is used in standalone or in a master slave setup with several units placed in one line one next to the other Press lt ENTER gt to confirm e You will be asked the amount of units that are linked in master slave set the number of linked units including the master Press lt ENTER gt to confirm e You will be asked which preprogrammed show you want to use choose from 1 1 to 1 8 Press ZENTER to confirm Note that this setting is only relevant while used without any controller you can change the speed using the menu buttons on the master e You will be asked which playback speed you want for the show choose from O to 255 Press ZENTER to confirm Note that this setting is only relevant while used without any controller you can change the speed using the menu buttons on the master e 10 10 select this option when the unit is used in a master slave setup with several units placed in a 10x10 matrix 10 units mounted on top of each other using the optional matrix bracket Press ZENTER to confirm e You will be asked which preprogrammed show you want to use choose from 2 1 to 2 8 Press ZENTER to confirm Note that this setting is only relevant while used without any controller you can change the speed using the menu buttons on the master e You will be
18. t To go back to the main menu without any change press the MENU button shortly If you want to go back to normal running mode press the MENU button for about 2 seconds Sound Sense Used to set the sensitivity of the internal microphone e Press the MENU button until Sound Sense is shown on the display e Press the ENTER button the display starts blinking e Use DOWN and UP button to select a value between 0 very low sensitivity and 100 high sensitivity e Once the mode is selected press the ENTER button save it To go back to the main menu without any change press the MENU button shortly If you want to go back to normal running mode press the MENU button for about 2 seconds BRITEQ 5 10 LED BLINDER WHITE ENGLISH OPERATION MANUAL Blackout Mode Blackout mode when no DMX signal is detected the unit goes in blackout and waits for a DMX signal No blackout mode when no DMX signal is detected the unit automatically switches to standalone mode e Press the MENU button until Black Out is shown on the display e Press the ENTER button the display starts blinking e Use DOWN and UP button to select Yes blackout on or No blackout off mode e Once the mode is selected press the ENTER button to save it To go back to the main menu without any change press the MENU button shortly If you want to go back to normal running mode press the MENU button for about 2 seconds Backlight Bac
19. tation damage Should there be any do not use the device and consult your dealer first Important This device left our factory in perfect condition and well packaged It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual Any damage caused by mishandling is not subject to warranty The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual Keep this booklet in a safe place for future consultation If you sell the fixture be sure to add this user manual Check the contents Check that the carton contains the following items BRITEQ 1 10 Operating instructions LED BLINDER WHITE unit Bracket knobs IEC power cable LED BLINDER WHITE ENGLISH OPERATION MANUAL SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove the top cover No user serviceable parts inside Refer servicing to qualified service personnel only The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance servicing instr
20. terials and or liquids The fixture must be fixed at least 50cm from surrounding walls Don t cover any ventilation openings as this may result in overheating Prevent use in dusty environments and clean the unit regularly Keep the unit away from children Inexperienced persons should not operate this device Maximum save ambient temperature is 40 C Don t use this unit at higher ambient temperatures Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing Always unplug the unit when it is not used for a longer time or before servicing The electrical installation should be carried out by qualified personal only according to the regulations for electrical and mechanical safety in your country Check that the available voltage is not higher than the one stated on the rear panel of the unit The power cord should always be in perfect condition Switch the unit immediately off wnen the power cord is squashed or damaged It must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Never let the power cord come into contact with other cables This fixture must be earthed in order to comply with safety regulations Don t connect the unit to any dimmer pack Always use an appropriate and certified safety cable when installing the unit In order to prevent electric shock do not open the cover Apart from the mains fuse t
21. uctions in the literature accompanying this appliance This symbol means Read instructions This symbol means Safety Class appliance ER This symbol means indoor use only q ug This symbol determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 1 meters surfaces include building materials such as wood and wood based materials more than 2mm thick CAUTION Possibly hazardous optical radiation emitted from this product To protect the environment please try to recycle the packing material as much as possible w The device is suitable for mounting on standard flammable surfaces Standard flammable e A new light effect sometimes causes some unwanted smoke and or smell This is normal and disappears after some minutes To prevent fire or shock hazard do not expose this appliance to rain or moisture To avoid condensation to be formed inside allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport Condense sometimes prevents the unit from working at full performance or may even cause damages This unit is for indoor use only e Don t place metal objects or spill liquid inside the unit Electric shock or malfunction may result If a foreign BRITEQ 2 10 object enters the unit immediately disconnect the mains power Locate the fixture in a well ventilated spot away from any flammable ma
22. ur website www beglec com BRITEQ 10 10 LED BLINDER WHITE
23. verheat the cooling fans and ventilation openings should be cleaned monthly e The interior of the device should be cleaned annually using a vacuum cleaner or air jet e The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics e Clean with a soft cloth using normal glass cleaning products and always dry the parts carefully e Clean the external optics at least once every 30 days e Clean the internal optics at least every 90 days Attention We strongly recommend internal cleaning to be carried out by qualified personnel SPECIFICATIONS Mains Input AC 100 240V 50 60Hz Power consumption 57 Watt max Power daisy chaining qty 10 units Fuse 250V 6 3A slow blow 20mm glass Sound Control Internal microphone DMX connections 3pin 5pin XLR male female DMX channels used 1 2 10 12channels special 4MSL Lamp 40pcs 1W LEDs 10clusters each with 4pcs 1W LEDs Size see drawing Weight 7 2kg D o en e sg e Ve gt o e ae KL E Ki E p d A S S o T GI Se Ss E E e 5 Ei j 964 Every information is subject to change without prior notice You can download the latest version of this user manual on o
Download Pdf Manuals
Related Search