Outdoor 2.4GHz Digital AV Sender - Control PTZ
Contents
1. Outdoor 2 4GHz Digital AV sender Control PTZ wirelessly Manual V1 0 Os yy he Please note the metal pole TV DVR Keyboard and PTZ camera are for demo purpose not included inside the package A What is inside the Box Please check the following items inside the box for 2 4Ghz Digital AV sender and contact your dealer if anything is missing 1 Products body Receiver x 1 Transmitter x 1 There will be a product label on the back side to show RX or TX model no 2 Accessory for receiver or transmitter Refer to the following photo from left to right Power Adaptor x 2 100V 240V AC DC 12V 1A in Jack AV cables x 2 3RCA plug to 1 phone plug Bracket set x 2 on the bottom row This user manual PAGE B Introduction Thank you for purchasing this Outdoor 2 4GHz Digital AV Sender This transmission system is a digital wireless audio video sender that uses 2 4GHz Frequency Hopping technology not fixed frequency and 16QAM QPSK BPSK modulation and random ID codes to protect personal privacy There are over billion hopping sequences to minimize interference and deliver consistently an excellent video and audio quality up to 5KM meters away by 200mW transmission power and 14dBi antenna Using this 2 4GHz Digital Wireless A V Sender you can enjoy greater convenience and security in many ways Safety amp Security Application Connect a PTZ camera as a wireless security system contro2. ceiver it needs to wait for a few seconds to insert it again 3 Adjust antenna to decrease interference vertical or horizontal 4 In most situations one pair has a better distance up to 3 5KM line of sight and open site When two pairs or more are used at the same time It can automatically jump to different channels But the distance between transmitter and transmitter receiver and receiver preferably greater than 3 meter far G Troubleshooting Monitor RX shows Camera power off or stolen camera cable disconnected or damaged No Video Signal please check and make it right Monitor RX shows TX power off TX RX distance 1s too long so that transmission signal 1s No Signal weak please check and make it right Check all cable connections Make sure power plugs are pushed all the way in Check power switches on the remote TV or DVR and Video No picture or sound source Camera Camcorder etc Check 1f the POWER LED of the transmitter and receiver is lighting or not Their LINK LED should be lit If Their LINK LED not be lit you must re pair their codes following the D instruction of the manual Adjust receiver and transmitter antenna orientation Try to place transmitter and receiver a little more close Interference picture or The transmission path between the pair may be overlapped to the other audio pair must install higher position or separate these two pairs There would be a high
3. fully the power LED for both will be lit directly not flash Pairing Button black vy e Pairing Light Please note Pressing the pairing buttons for transmitter and receiver is not necessary at the same time and they are not necessarily put near or side by side in pairing status around within 3 meters far is OK Under the transmission you can see the strength signal on the monitor RX as below and will disappear after 5 seconds press RX pairing button will make it shown again PAGE E RS485 control wirelessly RS485 of TX can connect PTZ Camera RS485 port and the RX RS485 port connect out to RS485 port of PTZ keyboard or DVR so that keyboard or DVR can control its Pan Tilt Zoom actions wireless and long distance please note the PTZ protocol used for this system is only Pelco P or Pelco D they are auto detect and must be same in the PTZ camera and PTZ keyboard or DVR baud rate are 9600bps 4800bps 2400bps 1200bps you have to setup the PTZ camera this system TX RX PTZ keyboard or DVR with same baud rate ey 3 on the PCBA as below ON is PAL 3 is NTSC baud rate is below RE ML Tg N i y si Aa a agi 1 this information will disappear shortly PAGE F Use Notics 1 Be sure the transmitter and the receiver were connected to the equipment correctly e g Connect the transmitter to the camera and the receiver to the TV or DVR 2 When DC plug is pulled out from transmitter or re
4. ional range up to SKM meters line of sight and open site Operation temperature 20 C 65 C eAll specification subject to change without notice PAGE
5. l its Pan Tilt Zoom actions via RS485 port from the receiver RX through PTZ keyboard or DVR with PTZ function With weather proof enclosure for TX RX suitable for outdoor like farm mountain park sea port and big garden C Product Layout and wire connection Bottom view for TX RX Weather proof super cable gland Dissemble the screws and super cable gland and open the bottom cover you can see bottom cover and enclosure as below Panel Antenna PCBA Bottom cover Panel Antenna side for TX RX must be directional to each other in the installation PAGE IASUSIVGSI j open the bottom cover and take DIP Switch for PAL NTSC Baud Rate and NTSC PAL RS485 port to connect PTZ camera TX or DVR PTZ Keyboard RX DC jack for power adaptor AV Jack for PTZ camera input TX or output to TV monitor DVR There are two brackets bracket 1 to secure on the metal pole bracket 2 to secure the enclosure bottom and bracket1 PAGE D Pairing the transmitter and receiver 1 Power on the transmitter and receiver by inserting the power adaptor jack 2 Press the pair button of transmitter or receiver and not release until the power LED begin to flash then release the pair button 3 They will enter into the pairing state and automatically link to each other by ID code after step 2 finished Please don t turn off their power switch during the paring status 5 When pairing success
6. power pair unit near by TX or RX please find 1t and move H Specifications Transmitter Operating Frequency Band 2 400GHz 2 4835GHz Modulation 1 6QAM QPSK BPSK Video Input Level 1V p p 75 ohm Audio Input Level 1V p p 600 ohm STEREO RS485 port control Pelco D or Pelco P protocol PTZ camera PAGE Baud rate 9600 4800 2400 1200 bps by DIP switch Antenna Directional Panel Antenna 14dBi PA Output Power 200mW Antenna Output Power 3WATTS EIRP Power consumption 1 9W Power supply 12V 1A Enclosure ABS material Dimension 25cm x 24cm x 7 7cm Weight 420gw Receiver Operating Frequency Band 2 400GHz 2 4835GHz Modulation 1 6QAM QPSK BPSK Receiver Sensitivity 85dBm min Video Output Level 1 0 2V p p 75 ohm Audio Output Level 1 0 2V p p 600 ohm STEREO RS485 port control Pelco D or Pelco P protocol PTZ camera Baud rate 9600 4800 2400 1200 bps by DIP switch Antenna Directional Panel Antenna 14dBi PA Output Power 200mW Antenna Output Power 3WATTS EIRP Power consumption 1 9W Power supply 12V 1A Enclosure ABS material Dimension 25cm x 24cm x 7 7cm Weight 420gw System Transmission channels 26 channels auto selection Video bit rate up to 12 Mbps Random ID code up to 4 million sets Video resolution 720 x 480 30 fps NTSC or 768 x 576 25 fps PAL PTZ camera control wirelessly Pelco D or Pelco P auto detect Baud rate 9600 4800 2400 1200 bps Operat
Download Pdf Manuals
Related Search