LED Lighting System Innovative, efficient and versatile.
Contents
1. MaZaP eee S Series Owner s Manual Innovative efficient and versatile Dear Customer Thank you for purchasing this product For optimum performance and safety please read these instructions carefully User Memo Date of purchase Dealer name Dealer address Dealer website Dealer email Dealer phone no O LED Module Product O Mounting Frame Set O Power Supply Unit Please visit us on facebook or twitter ij http twitter com maxspectled https www facebook com paqges Maxspect LED 283406251689606 A lt Ma xspect Package Content Please check the content in the package LED Module Ball Joint Mount Rail System Power Supply Cooling Fan T Joint Cable Cable Organizer Accessories eo AY Optic Lens Sets 100 70 40 Vmaxspect Before using this Maxspect Mazarra LED Lighting System please read these operating instructions carefully Take special care to follow the safety suggestions listed below Afterwards keep this manual handy for future reference Before using the Maxspect Mazarra LED Lighting System 1 Remove any protective film covering the lens of the LED bulbs before use 2 Never look directly at the LED bulbs when you switch on the system Incorrect use of this apparatus will increase eye hazard On Safety 1 Power Source Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has2. When finished press and hold Control Dial to save the setting The setting is now saved 16 maxspect Operating Instructions LED Module Automatic Mode In Automatic Mode you can program the photo period to have the LED Modules turn on and off by itself Setting the Clock This Mazarra LED Lighting System incorporates a 24 hour clock The clock must be set for the Automatic Mode programs to operate correctly 1 Press and hold Control Dial for 3 seconds to enter setup You will see three settings here Time Program and Temperature 2 Rotate Control Dial to select TIME and press Control Dial You can now set the clock 3 Rotate Control Dial to change the hour digit press Control Dial to confirm repeat for the minute digit The clock is now set 4 Press o Select Button to return to the previous setup menu 17 A gt maxspect Operating Instructions Setting up Photoperiod Programs The LED Module can be programmed to control the photoperiod and brightness of the system throughout the day Understanding Time Points There are a total of 4 Time Points You can program different luminous output intensity at each Time Point to control the photoperiod and brightness of the system For example the following table demonstrates how you could program the Time Points such that the system would increases light gradually from 8 00am peaks at 10 00am 2 00pm then slowly de
3. two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 2 Power Cord Protection The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Never take hold of the plug or cord if your hand is wet and always grasp the plug body when connecting or disconnecting it 3 Installation Install indoor only and use the attachments mounting frames hanging kit and accessories provided and specified by the manufacturer On Operation 1 Operation Always follow the operation instructions set forth in this manual when using this Mazarra LED Lighting System 2 Heat The apparatus should be situated away from heat sources such as radiators and do not expose to excessive heat such as sunshine fire or the like 3 Moisture To reduce the risk of fire or electric shock do not expose this apparatus to rain moisture dripping or splashing 4 Ventilation The apparatus should be situated so that its location or position does not interfere with its proper ventilation 5 Magnetism The apparatus should be situated away from equipment or devices that generate strong magnetism 6 Cleaning Clean only with dry cloth Vm ma xspect I
4. ALTERATION ACCIDENT IMPROPER HANDLING OR OPERATION OR IF UNAUTHORIZED REPAIRS ARE ATTEMPTED OR MADE SOME EXAMPLES OF DAMAGES NOT COVERED BY WARRANTY INCLUDE BUT ARE NOT LIMITED TO USING AFTER MARKET LED BULBS AND MODIFICATION OF THE CIRCUITRY WHICH ARE PRESUMED TO BE DAMAGES RESULTING FROM MISUSE OR ABUSE DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES You and any other user of Maxspect Ltd products shall not be entitled to any consequential or incidental damages including without limitation loss of use of the unit inconvenience damage to personal property phone calls lost income or earnings This warranty gives you specific legal rights and you may also have other rights which vary from state to state MAXSPECT LTD MAKES NO WARRANTY OR REPRESENTATION EITHER EXPRESS OR IMPLIED WITH RESPECT TO THE PRODUCT S QUALITY PERFORMANCE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS A RESULT THIS PRODUCT IS SOLD AS IS AND YOU THE PURCHASER ASSUME THE ENTIRE RISK AS TO ITS QUALITY AND PERFORMANCE IN NO EVENT WILL MAXSPECT LTD BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY DEFECT IN THE PRODUCT OR ITS DOCUMENTATION The warranty disclaimer and remedies set forth above are exclusive and replace all others Oral or written expressed or implied At no time will any Maxspect Ltd dealers agents or employees be authorized to make any modifications extension or additio
5. and hold O Select Button for 2 seconds to switch between Manual Mode and Automatic Mode 2 Press Control Dial to turn on the backlight on the LCD Display The backlight will turn off automatically after 30 seconds of idling LED Module Status 1 Intensity of the 2 LED channels temperature of the LED Module and status of the fan will be shown on the LCD Display 15 Va U maxspect Operating Instructions LED Module Manual Mode In Manual Mode you can adjust the intensity of the 2 LED channels and Active Cooling setting directly from the LED Module Turning on the LED Channels 1 2 Press 0 Select Button to turn on all 2 LED channels simultaneously Press O Select Button the button again to turn them off Control the LED Module in Manual Mode 1 Cm Press and hold Control Dial for 3 seconds to enter setup Channel A will be selected first To adjust brightness of the selected channel rotate Control Dial Rotate clockwise will increase the brightness and vice versa Press Control Dial to switch to the next LED channel Repeat 2 for channel B Press Control Dial again to adjust the Active Cooling setting Active Cooling means the minimum temperature the LED Module must reach before the fan will be turned on automatically To adjust the temperature rotate Control Dial There are 5 settings 40 C 104 F 45 C 113 F 50 C 122 F 55 C 131 F and 60 C 140 F
6. ate Control Dial to adjust brightness for this channel then press Control Dial to switch to the next channel and repeat 5 and 6 Note At 0 intensity the channel is turned OFF l Repeat 3 to 7 for all 4 Time Points 8 Press 0 Select Button to confirm and return to main menu The settings are now saved aa 9 V naxspect i Operating Instructions Adjusting Active Cooling Setting 1 Active Cooling means the minimum temperature the LED Module must reach before the fan will be turned on automatically Press and hold Control Dial for 3 seconds to enter setup Rotate Control Dial to select TEMPERATURE and press Control Dial You can now adjust the Active Cooling Setting To adjust the temperature rotate Control Dial There are 5 temperature settings 40 C 104 F 45 C 113 F 50 C 122 F 55 C 131 F and 60 C 140 F Press 0 Select Button to confirm and return to main menu The setting is now saved V naxspect 20 Limited Warranty Maxspect Ltd warrants all Maxspect Mazarra LED Lighting System products against defects in workmanship for a period of 12 months from the date of purchase If a defect exists during the warranty period Maxspect Ltd at its option will either repair using new or remanufactured parts or replace with a new or remanufactured unit the product at no charge THE WARRANTY WILL NOT APPLY TO THE PRODUCT IF IT HAS BEEN DAMAGED BY MISUSE
7. creases light until it is turned off at 10 00pm TP1 TP2 TPS TP4 08 00 10 00 14 00 22 00 Channel A OFF 100 100 OFF Channel B OFF 100 100 OFF The following diagram would illustrate how the 2 LED channels would behave once the above Time Points have been programmed O Channel A O Channel B Setting up Moon Light Moon Light can be programmed by simply assign one of the LED channels preferably the blue LED channel to operate at 1 brightness in the last Time Point TP1 TP2 TPS TP4 08 00 10 00 14 00 22 00 Channel A OFF 100 100 OFF Channel B 1 100 100 1 Cna xspect 18 Operating Instructions Programming Time Points 1 Press and hold Control Dial for 3 seconds to enter setup You will see three settings here Time Program and Temperature 2 Rotate Control Dial to select PROGRAM and press Control Dial You can now program the Time Points 3 Rotate Control Dial to select the Time Point 1 4 4 Press Control Dial to switch to the timer rotate Control Dial to change tt The timer will increment decrement in 30 minutes intervals Note Changes you made to a Time Point will affect all subsequence Time Points to prevent erroneous behavior For example if you change the timer to a larger value than the next Time Point the system will push the next Time Point to the same time with a maximum value of 23 30 5 Press Control Dial to switch to Channel A 6 Rot
8. els are trademarks of Philips Lumileds Lighting Company S Series Owner s Manual Version 1 5 0
9. n to this warranty Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages so the above limitation or exclusion may not apply to you maxapect n Controller Unit Dimensions D x L Weight LED Module Dimensions D x L Weight Power Supply Input Voltage Output Voltage Output Current LED Bulbs Channel Make Model Cree XLamp XP E A 8 R3 Cree XLamp XP E M2 i Cree XLamp XP E 16 Note Specifications are subject to change without notice Weight and dimensions are approximate 4 Specifications 120mm x 60mm x 30mm 4 7 x 2 4 x 1 2 300g 10 oz 0230mm x 230mm x 35mm 9 x 9 x 1 5 2kg 4 4 Ib AC 100 240V 50 60 Hz 36V 3 5A Quantity Luminous Flux amp Color Temperature Driven Current Wavelength Cool White 7000 8000K Blue 465 485nm Royal Blue 450 465nm 280 Im 1000mA 69 Im 1000mA 1000mW 1000mA 22 Maxspect Innovative efficient and versatile Maxspect Limited www maxspect com NOTE Products packaging features and specifications are subject to change All screen images are simulated 2009 2011 Maxspect Limited Reproduction in whole or in part without written permission is prohibited All rights reserved Maxspect and Mazarra are trademarks of Maxspect Limited Cree and XLamp are trademarks of Cree Inc Bridgelux is trademark of Bridgelux Inc Philips and Luxeon Reb
10. nce of your Mazarra LED Lighting System You must install one of the three types of optics on every bulb The optics also serves as a protective barrier that prevents water and moisture from damaging the LED bulbs 11 V naxspect Installation Installing Changing Optics 1 Using a small slotted screwdriver carefully remove the screws on the bottom panel and remove it 3 Place the new optics over the slot and apply pressure on it until you hear it snaps Vmaxspect 12 Installation Passive Active Cooling With the new Cree XLamp XM L chip higher efficiency means less power is consumed and the Mazarra runs cooler than its predecessors Together with an ingenious aerodynamic design the Mazarra is passively cooled when warm air passes through its aluminum chassis Nonetheless in the situation where you do need to actively cool your LED Module for example your Mazarra is installed in a confined space such as a canopy you can install the optional fan by following the below instructions The fan is temperature controlled it will only turn on when the temperature rises above a preset value see Operating Instructions on the LED Module and Controller Unit Installing the optional fan will ensure the module runs at optimal temperature and prolong the lifespan of LED Bulbs Installing the Optional Fan 1 Insert the fan onto the slot as indicated by the diagram below and connect the po
11. ndex to Parts and Controls LED Module 1 oO Select Button 6 Rail System 2 Control Dial 7 Rail Connector 3 LCD Display 8 Cable Organizer 4 Thumb Screw 9 Power Supply Cable 5 Ball Joint Mount Installation Mounting the Mazarra LED Lighting System Before connecting the LED Modules to Power Supply first mount the system by using the provided Frame Set 1 Assemble the Frame Set Assemble the frame set by connecting sections together to form a secured structure as illustrated in the following diagrams Standard Frame Set Packages are illustrated below 240mm 9 4 ee SSE Package C 0 60mm 2 4 SS ae 200mm 7 9 d gt SO FS SS NMOOAy YS SSS WY A NNG SS N N A Package B 190mm 7 5 E Package D 285mm 11 2 Package E Aluminium Rail comes with the LED Module 200mm 7 9 Package F Package G POOOE V naxspect Installation 2 Pendant Mounting For a single row configuration you can assemble the frame set as illustrated below 3 Mounting inside the Canopy You can mount the system onto the top of your canopy as illustrated below Installation 4 Mounting on Cabinet Stand You can mount the system on the cabinet stand of your aquarium as illustrated below Package EX2 G 9 Mounting on Wall You can mount the system on wall as illustra
12. ted below Package EX2 Installation 6 Mounting on Aquarium You can mount the system on your aquarium by resting the frame on the glass acrylic panels as illustrated below Package A D Package A E Op AA 73 2 k7 Package B E Package B D Package A DX2 Package AX2 DX2 FX3 rmaxspect Installation The maximum width of the glass acrylic the stand can fit onto is 20mm 3 4 The stand can be mounted on top of the glass acrylic panel or sideway on support beams found on larger aquariums l Mounting and positioning the LED Lighting System Depends on the dimensions of your aquarium there are many different configurations you could mount and position the Mazarra LED Lighting System Installation Powering the Mazarra LED Lighting System Power Supply A sample connection configuration utilizing 2 LED Modules 1 Each Power Supply can power up to 2 LED Modules 2 For additional LED Modules you must connect more Power Supplies maxanect j Installation Optics Each Mazarra LED Module comes with three sets of optics ranges from 100 70 to 40 factory default is 100 Installing optics will enhance penetration of light over a greater depth of water by converging light from the LED bulbs but at the same time reducing the coverage area By mix and matching different types of optics to be installed you would be able to customize the overall appearance and performa
13. wer cable 13 Cmaxanect Changing Replacing LED Bulbs The Mazarra is the only LED Lighting System available on the market that offers both plug and play LED bulb replacement design and LED bulbs covering the entire color spectrum allowing maximum customization and flexibility By mix and matching colored LED bulbs Mazarra allows you to pick the right color spectrum for your aquarium and bring out that color from your corals exactly like you have always dreamed of 1 Open the LED Module the same way as you would replace Optics Please refer to Installing Changing Optics section for detail instructions 2 Carefully loosen and remove the screws then lift the clasp holding the LED Bulb chip to replace it ss g oe ae ee 7 oe t CIs Es EzE Nn pD oe a gt A LZ p gt e TS POR CS 3 When finished return the clasp to its original position and tighten the Screws Vmnaxspect j Operating Instructions The LED Module Follow the instructions below to operate and program the LED Module The LED Module turns on automatically when power is connected and turns off when power is cut When power is resumed the LED Module will restore to the previous saved setting automatically whether it was last set at Standalone Mode or Connected Mode and the intensity level of all the LED channels Switching between Manual and Automatic Mode 1 Press
Download Pdf Manuals
Related Search