Z-Wave Aeon Labs LED Bulb - Gen5 Manual
Contents
1. bulb has 5 main colour channels available for you to adjust Red Green Blue Warm white and Cold white You can configure its indication colour according to your favour LED Bulb can be included and operated in any Z Wave network with other Z Wave certified devices from other manufacturers and or other applications All non battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network The LED Bulb is a security Z Wave device so a security enabled controller is needed for take full advantage of all functionally for the LED Bulb It also supports the Over The Air OTA feature for the product s firmware upgrade 1 Library and Command Classes 1 1 SDK 6 51 06 1 2 Library Basic Device Class BASIC_TYPE_ROUTING_SLAVE Generic Device class GENERIC_TYPE_SWITCH_MULTILEVEL Specific Device Class SPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL 1 3 Commands Class Node Info COMMAND_CLASS_ZWAVEPLUS_INFO V2 COMMAND_CLASS_ZWAVEPLUS_INFO V2 Frame COMMAND_CLASS_SWITCH_MULTILEVEL V2 COMMAND_CLASS_VERSION V2 COMMAND_CLASS_SWITCH_COLOR V1 COMMAND_CLASS_MANUFACTURER_SPECIFIC V2 COMMAND_CLASS_SWITCH_ALL V1 COMMAND_CLASS_SECURITY V1 COMMAND_CLASS_SCENE_ACTUATOR_CONF V1 COMMAND_CLASS_MARK V1 COMMAND_CLASS_SCENE_ACTIVATION V1 COMMAND_CLASS_DEVICE_RESET_LOCALLY V1 COMMAND_CLASS_CONFIGURATION V1 COMMAND_CLASS_HAIL V1 COMMAND_CLASS_ASSOCIATION_GRP_INFO V1 COMMAND_CLASS_ASSOCIATION V2 COMM2. version Max operating power 9W Operating temperature 10 C to 45 C Relative humidity 8 to 80 Operating distance Up to 500 feet 150 metres outdoors AC Input Version Input Standby Power Working band AU 230V 50Hz Max 0 7W 921 42MHz BR 220V 60Hz Max 0 7W 921 42MHz CN 220V 50Hz Max 0 7W 868 40MHz EU 230V 50Hz Max 0 7W 868 42MHz IL 230V 50Hz Max 0 7W 916 02MHz IN 230V 50Hz Max 0 7W 865 20MHz UK 230V 50Hz Max 0 7W 868 42MHz US 120V 60Hz Max 0 5W 908 42MHz Warranty Aeon Labs warrants to the original purchaser of Products that for the Warranty Period as defined below the Products will be free from material defects in materials and workmanship The foregoing warranty is subject to the proper installation operation and maintenance of the Products in accordance with installation instructions and the operating manual supplied to Customer Warranty claims must be made by Customer in writing within thirty 30 days of the manifestation of a problem Aeon Labs sole obligation under the foregoing warranty is at Aeon Labs option to repair replace or correct any such defect that was present at the time of delivery or to remove the Products and to refund the purchase price to Customer The Warranty Period begins on the date the Products is delivered and continues for 12 months Any repairs under this warranty must be conducted by an authorized Aeon Labs s
3. AEOTEC LED BULB View the expanded manual http aeotec com support Q Aeotec by Aeon Labs LED Bulb Aeotec LED Bulb is a low cost Z Wave LED module which allows control on off dim with the use of Z Wave It s a bulb has a Smart RGB LED which can be used to add colour to your home The bulb has 5 main colour channels available for you to adjust Red Green Blue Warm White and Cold White You can configure its colour according to your favour The LED Bulb is also a security Z wave device and supports the Over The Air OTA feature for the product s firmware upgrade Familiarize yourself with your LED Bulb Quick start Getting your LED Bulb up and running is as simple as plugging it into a wall socket and include it to your existing Z Wave network The following instructions tell you how to include your LED Bulb to your Z Wave network using an Aeotec by Aeon Labs Z Stick or Minimote controller If you are using other products as your main Z Wave controller such as a Z Wave gateway please refer to the part of their respective section of their instruction manual that tell you how add new devices to your network External Switch Note If you use other Z wave controller the first step is let your controller into inclusion exclusion mode the next step will be the same with the step 5 or 4 of using Z Stick Minimote If you re using a Z Stick ak w 7 S A Decide on where you want yo
4. AND_CLASS_MANUFACTURER_SPECIFIC V2 COMMAND_CLASS_VERSION V2 COMMAND_CLASS_FIRMWARE_UPDATE_MD V2 COMMAND_CLASS_POWERLEVEL V1 COMMAND_CLASS_ SECURITY v1 COMMAND_CLASS_MARK V1 COMMAND_CLASS_DEVICE_RESET_LOCALLY V1 COMMAND_CLASS_HAIL V1 Security COMMAND_CLASS_SWITCH_MULTILEVEL V2 Command COMMAND_CLASS_SWITCH_COLOR V1 Supported COMMAND_CLASS_SWITCH_ALL V1 Report COMMAND_CLASS_SCENE_ACTUATOR_CONF V1 Frame COMMAND_CLASS_SCENE_ACTIVATION V1 COMMAND_CLASS_CONFIGURATION V1 COMMAND_CLASS_ASSOCIATION_GRP_INFO V1 COMMAND_CLASS_ASSOCIATION V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC V2 COMMAND_CLASS_VERSION V2 COMMAND_CLASS_FIRMWARE_UPDATE_MD V2 COMMAND_CLASS_POWERLEVEL V1 COMMAND_CLASS_DEVICE_RESET_LOCALLY V1 COMMAND_CLASS_HAIL V1 2 Technical Specifications Model number ZW098 Bulb holder type E26 for USA version E27 for EU AU version Max operating power 9W Max standby power 0 7W Operating temperature 10 C to 45 C Relative humidity 8 to 80 Operating distance Up to 500 feet 150 metres outdoors 3 Familiarize Yourself with Your LED Bulb 3 1 Interface 4 Inclusion Exclusion of LED Bulb External Switch Or ZON BS rd ii External Switch fo ee Add include 1 Power on your LED Bulb as above the wire diagrams LED Bulb into 2 Let the primary controller into inclusion mode If you don t know how to do this please Z Wave refer to its manual Network 3 Turn off the LED Bulb and t
5. S AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY 30 DAYS FROM AEON LABS S DELIVERY OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER INDEMNITIES OR WARRANTIES WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE FCC NOTICE for USA THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT STORE INDOORS WHEN NOT IN USE SUITABLE FOR DRY LOCATIONS DO NOT IMMERSE IN WATER NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful
6. configure it to indicate different colours from your home control software via setting the RGB value Please refer to your software s user guide for precise instructions on configuring your LED Bulb to your needs You re able to change your LED Bulb s colour manually After the LED Bulb is included into your network switching the LED Bulb on and off 2 times before the Power Outage LED is turned off via external switch will change the colour to the next Warm white Cold white Red Green or Blue Note The Power Outage LED is a small red LED in the Bulb which is used to indicate the power outage state of the LED Bulb When the LED Bulb is switched off by the external Switch it will keep solid with red light for 1 2 second and then be turned off automatically Excluding your LED Bulb from a Z Wave network Your LED Bulb can be removed from your Z Wave network at any time You ll need to use your Z Wave network s main controller and to do this and the following instructions will tell you how using the Aeotec by Aeon Labs Z Stick or Minimote controller If you are using other products as your main Z Wave controller please refer to the part of their respective manuals that tells you how remove devices from your network If you re using a Z Stick Ky 7 1 If your Z Stick is plugged into a gateway or a computer unplug it Take your Z Stick to your LED Bulb Press the Action Button on your Z Stick Press the ext
7. ernal switch of LED Bulb to turn off and then press the external switch again to turn on it repeat the operation 3 times before the Power Outage LED is turned off 5 If your LED Bulb has been successfully excluded from your network Its RGB LED will be active with a colourful AUN gradient If the exclusion was unsuccessful the RGB LED will be solid 6 Press the Action Button on the Z Stick to take it out of exclusion mode If you re using a Minimote Remove 1 Take your Minimote to your LED Bulb 2 Press the Remove Button on your Minimote 3 Press the external switch of LED Bulb to turn off and then press the external switch again to turn on it repeat the operation 3 times before the Power Outage LED is turned off 4 If your LED Bulb has been successfully excluded from your network Its RGB LED will be active with a colourful gradient If the removal was unsuccessful the RGB LED will be solid 5 Press any button on your Minimote to take it out of exclusion mode e Reset your LED Bulb At some stage may be your primary controller is missing or inoperable you can let your new controller into exclusion mode and then press the external switch to turn the Bulb off and then to turn on it repeat the operation 3 times After the LED Bulb is excluded from network it will be reset to factory default state Technical specifications Model number ZW098 Bulb holder type E26 for USA version E27 for EU AU
8. ervice representative and under Aeon Labs RMA policy Any repairs conducted by unauthorized persons shall void this warranty Excluded from the warranty are problems due to accidents acts of God civil or military authority civil disturbance war strikes fires other catastrophes misuse misapplication storage damage negligence electrical power problems or modification to the Products or its components Aeon Labs does not authorize any person or party to assume or create for it any other obligation or liability in connection with the Products except as set forth herein Aeon Labs will pass on to Customer all manufacturers Material warranties to the extent that they are transferable but will not independently warrant any Material Customer must prepay shipping and transportation charges for returned Products and insure the shipment or accept the risk of loss or damage during such shipment and transportation Aeon Labs will ship the repaired or replacement products to Customer freight prepaid Customer shall indemnify defend and hold Aeon Labs and Aeon Labs affiliates shareholders directors officers employees contractors agents and other representatives harmless from all demands claims actions causes of action proceedings suits assessments losses damages liabilities settlements judgments fines penalties interest costs and expenses including fees and disbursements of counsel of every kind i based upon
9. hen turn on it via pressing the external switch 4 If the inclusion is failed please repeat the process from step 2 Note If LED Bulb has been successfully linked to your Z Wave network its warm white LED will be solid If the linking was unsuccessful and the LED Bulb continues to be active with a colourful gradient Remove exclu 1 Power on your LED Bulb as above the wire diagrams de LED Bulb 2 Let the primary controller into inclusion mode If you don t know how to do this please from Z Wave refer to its manual Network 3 Turn off the LED Bulb and then turn on it repeat the operation 3 times within 2 seconds via pressing the external switch 4 If the inclusion is failed please repeat the process from step 2 Note If your LED Bulb has been successfully removed from your network Its RGB LED will be active with a colourful gradient If the removal was unsuccessful the RGB LED will be solid 5 Special Rule of Each Command 5 1 Z Wave Plus Info Report Z Wave Plus Version 1 Role Type 5 ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_ALWAYS_ON Node Type O ZWAVEPLUS_INFO_REPORT_NODE_TYPE_ZWAVEPLUS_NODE Installer Icon Type 0x0600 ICON_TYPE_GENERIC_LIGHT_DIMMER_SWITCH User Icon Type 0x0600 ICON_TYPE_GENERIC_LIGHT_DIMMER_SWITCH 5 2 Manufacturer Specific Report 0x01 Manufacturer ID 1 Manufacturer ID 2 Ox6A Product Type ID 1 EU 0
10. interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consul the dealer or an experienced radio TV technician for help Warning Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems available Certifications regional Z Wave and Z Wave Plus are registered trademarks d el 3 of Sigma Designs and its ae PLES subsidiaries in the United Intertek States and other countries 4005555 N29634 FCC ID XBAFT107 p lt CE K aD Version 501009800001 AA www aeotec com AEOTEC BY AEON LAES Aeon Labs LED Bulb Engineering Specifications and Advanced Functions for Developers Aeon Labs LED Bulb is a switch multilevel device based on Z wave enhanced 232 slave library of V6 51 06 Its bulb has the Smart RGB LEDs in which can be used for adding colour to your home the
11. l be ignored The Scene Actuator Configuration Get Command is used to request the settings for a given scene if scene ID is not setting it will be ignored If Scene ID 0 then the LED Bulb will report currently the activated scene settings If the currently activated scene settings do not exist the LED Bulb will reports Level currently load status and Dimming Duration 0 5 6 Scene Activation Set Command Class The Scene Activation Set Command is effective when only Level gt 0 and Level lt 0Ox64 or Level Oxff otherwise it will be ignored If the requested Scene ID is not configured it will be ignored too 5 7 Color Control State Set Command Class Priority capabitityio eoor o O 1 Highest 0 Warm white 2 1 Cold white 3 lowest 2 3 4 R G B Note White LED and RGB LED will not light up at the same time so the software makes the following processing When you want to activate the current RGB color the color value of higher priority should be set to 0 For example The warm white is the highest priority when it is configured to 0 the Cold white or RGB color configuration values can be activated Otherwise the bulb is always be activated by warm white 5 8 Configuration Set Command Class Command Class COMMAND_CLASS_CONFIGURATION Command CONFIGURATION_SET Parameter Number Default Reserved Size Configuration Value 1 MSB Configuration Value 2 Configuration Val
12. personal injury or death or injury to property to the extent any of the foregoing is proximately caused either by a defective product including strict liability in tort or by the negligent or willful acts or omissions of Customer or its officers employees subcontractors or agents and or ii arising from or relating to any actual or alleged infringement or misappropriation of any patent trademark mask work copyright trade secret or any actual or alleged violation of any other intellectual property rights arising from or in connection with the products except to the extent that such infringement exists as a result of Aeon Labs manufacturing processes IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT INCIDENTAL PUNITIVE SPECIAL OR CONSEQUENTIAL DAMAGES OR DAMAGES FOR LOSS OF PROFITS REVENUE OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY WHETHER IN AN ACTION IN CONTRACT OR TORT OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AEON LABS LIABILITY AND CUSTOMER S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS WHETHER BASED ON NEGLIGENCE STRICT LIABILITY BREACH OF WARRANTY BREACH OF AGREEMENT OR EQUITABLE PRINCIPLES IS EXPRESSLY LIMITED TO AT AEON LABS OPTION REPLACEMENT OF OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DAMAGES ARE CLAIMED ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THI
13. ue n LSB Parameter Number Definitions 8 bit 0x22 34 Enable disable the function of using External Switch to turn 0 1 on off the bulb O disable 1 enable Others ignore 0x23 35 Enable disable the function of using External Switch to 1 changes the bulb s color O disable 1 enable Others ignore 0x50 80 Enable to send notifications to associated devices Group 1 1 US version when the state of LED Bulb is changed O nothing 1 hail CC 2 other 2 basic CC report version OxC8 200 Partner ID 0 O Aeon Labs Standard Product OxFC 252 Enable disable Lock Configuration 0 disable 1 enable 0 Value 0 the setting of configuration parameters is allowed Value 1 all configuration parameters cannot be set Locked OxFF 255 1 Value 0x55555555 Default 1 Size 4 N A Reset to factory default setting and removed from the z wave network 2 Value 0 Default 1 Size 1 N A Reset to factory default setting
14. ur LED Bulb to be placed and plug it in to a wall outlet Its RGB LED will be active with a colourful gradient If your Z Stick is plugged into a gateway or a computer unplug it Take your Z Stick to your LED Bulb Press the Action Button on your Z Stick Press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on If LED Bulb has been successfully included to your Z Wave network its warm white LED will be solid If the inclusion was unsuccessful the LED Bulb will continue to be active with a colourful gradient Press the Action Button on the Z Stick to take it out of inclusion mode and return it to your gateway or computer If you re using a Minimote Include 1 Decide on where you want your LED Bulb to be placed and plug it in to a wall socket Its RGB LED will be active with a colourful gradient Take your Minimote to your LED Bulb Press the Include button on your Minimote Press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on 5 If LED Bulb has been successfully included to your Z Wave network its warm white LED will be solid If the inclusion was unsuccessful and the LED Bulb will continue to be active with a colourful gradient 6 Press any button on your Minimote to take it out of inclusion mode APUN With your LED Bulb now working as a part of your smart home you ll be able to
15. x00 US 0x01 AU 0x02 Product Type ID 2 0x03 Product ID 1 0x00 Product ID 2 0x62 Ox6b CUBE version 5 3 Association Command Class The LED Bulb supports 2 association groups and Max 5 nodes for each group Association Nodes Send Mode Send commands Group Group 1 0 N A N A 1 Single Cast When the state of LED Bulb turn on off the bulb is changed 2 5 1 Set Configuration parameter 80 to 0 Reserved Default 2 Set Configuration parameter 80 to 1 Send Hail CC 3 Set Configuration parameter 80 to 2 Send the Basic Report Group 2 0 N A N A 1 5 Single Cast Forward the Basic Set Switch Binary Set Switch Multilevel Start Level Change Switch Multilevel Stop Level Change Switch Multilevel Set Scene Activation Set to associated nodes in Group 2 when the LED Bulb receives the Basic Set Switch Binary Set Switch Multilevel Start Level Change Switch Multilevel Stop Level Change Switch Multilevel Set Scene Activation Set commands from main controller 5 4 Association Group Info Command Class 5 4 1 Association Group Info Report Command Class Profile General NA Profile MSB 0 Profile LSB 0 5 4 2 Association Group Name Report Command Class Group 1 Lifeline Group 2 Retransmit 5 5 Scene Actuator Conf Command Class The LED Bulb supports max 255 Scene IDs The Scene Actuator Conf Set command is effective when only Level gt 0 and Level lt 0x64 or Level Oxff otherwise it wil
Download Pdf Manuals
Related Search