USER`S MANUAL
Contents
1. a Connect the black test lead to the COM jack and the red test lead to the jack b Press D to select 2 enter the Q measurement Auto range by press key and Manual range by press SAN Manual range connect the red lead to black leads will display the measure range 000 00 gt 6600 range 0 000 KO gt 6KQ range 00 00 KO gt 66KQ range Ver STPV1 32 Page 23 CCTV testerPRO User s Manual 000 0 KO gt 660KO range 0 000 MQ gt 6MQ range 00 00 MO gt 66MQ range c Connect test leads across the resistance under measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates overrange situation and the higher range has to be selected F Continuity Testing WARNING When testing the circuit continuity be sure that the power of the circuit has been shut down and all capacitors have been discharged fully a Connect the black test lead to the COM jack and the red test lead to the jack b Press p G to select enter the continuity test c Connect test leads across two point of the circuit under testing d If continuity exists i e resistance less than about 502 built in buzzer will sound e You can get reading from LCD NOTE If input open circuit or the circuit resistance measured 1s higher than 660Q then the figure OL will be display G Diode Testing a Connect the black test lead to the COM jack and the red test lead to the ja2. It can last 12 hours for normal use after charging for 4 hours CCTV testerPRO Kits Professional design light and portability video display and data control are deliberately integrated which makes the instrument so simple practicable easy for use that the training is almost unnecessary for an operator to be skillful Ver STPV1 32 2 3 Front Panel 1 CCTV testerPRO 2 Power Supply 5V 2A Ver STPV1 32 CCTV testerPRO User s Manual i u P 3 LAN Cable Tester 5 BNC Cable 6 Safety cord 7 RS485 data cable Lithium Ion Polymer Battery 8 Instruction Manual Page 5 CCTV testerPRO User s Manual LA Ooo 3 CT y 2 z Tr Pa mage 7 LLaPTZ controller 0000 5 Video Setting Colorbar generator Cable tester 6 Data monitor Device sting Address search Digital multimeter i rT T mr T4 a om 1 i F i pg 3 i HH M DE set drowerf tf T 8 mj i ha FI om Anr Ee T T 40 18 te vce Ll 45 A Wa ee EE BE B AT bil Wp Eh nn i K ID a In dd a I PN mall Plt 4a 43 rh HT 4 i ed F 2 Lr me The data reception indicator it lights red while the data is being received The data transmission indicator it lights red while the data is being transmitted The charge indicator it lights red while the battery
3. CCTV testerPRO In case of RS485 A to A B to B Page 16 Ver STPV1 32 CCTV testerPRO User s Manual b Press SET key and then press A or hd key to select communication port according to the system connection Press SET key to save the change d Press FA or LY key to select the baud rate according to the baud rate of controlling system and then press SET key to save the change and capture command data from controlling system e Press RETURN key to clear the screen 3 8 Device setting Set the parameters of the CCTV testerPRO Auto poweroff Setting the time of auto shut down Disable 5 10 60 Disable Disable the Auto poweroff function 5 means the CCTV will power off after 5 minutes when there is no any operation Keypad tone Open or close the beep of pressing keypad Language Select language of OSD menu Brightness Setting the brightness of OSD menu and background 0 7 Address search off on Open or close the PTZ address search Menu a Press A or v key to move the parameter we want to change b Press or gt to change the value c Press ENTER to save the change or press RETURN key to give up the change Ver STPV1 32 Page 17 CCTV testerPRO User s Manual 3 9 PTZ address scanning Search up the ID of PTZ camera Note Please isolate the PTZ camera with other PTZ cameras before searching up Otherwise all the PTZ cameras in the same system will pan at the same time Press keyst
4. STPV1 32 CCTV testerPRO User s Manual m When the meter is linked to a measurement circuit do not touch unused terminals Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground B Atthe manual range when the value scale to be measured is unknown beforehand set the range selector at the highest position m Always be careful when working with voltages above 60V DC or 30V AC keep fingers behind the probe barriers while measuring m Never connect the meter with any voltage source while the function switch is in the current resistance capacitance diode continuity otherwise it will damage the meter m Never perform capacitance measurements unless the capacitor to be measured has been discharged fully m Never measure any of resistance capacitance diode or continuity measurements on live circuits 2 Introduction The CCTV testerPRO is developed for the On Site installation and maintenance of video monitoring system It can be used for displaying video controlling PTZ generating images capturing data of RS485 and testing LAN cable etc Its functions easy operation and portability makes it simple for the CCTV technician to install and maintain CCTV system improving work efficiency and get the labor cost down 2 1 Features m 3 5 TFT LCD 960 H x240 V resolution m Video Level testing video signals measured in IRE or mV B DC12V 1A power output for camera B Audio input testing m Digi
5. is being charged As the charging is complete the indicator turns off automatically 5 a The display Icon of battery electricity it displays the electric quantity 6 Main menu it shows main functions of CCTV testerPRO 7 a Sub menu Shows and sets the values of functions Ver STPV1 32 Page 6 CCTV testerPRO User s Manual Long pressing it more than 2 seconds to turn on off the tester short pressing to turn on off the PTZ controller menu displaying Menu key it pops up the main menu constant press it or press the 4 or key can shift between functions Setup key press it or press left or right key to enter sub menu to set the parameters of functions Upward Select the item which will be set or add the value of the parameter Tilt the PTZ upward Leftward Enter the sub menu or select the parameter whose value will be changed Reduce the value of the parameter Pan the PTZ left Rightward Enter the sub menu or select the parameter whose value will be changed Add the value of the parameter Pan the PTZ right Downward Select the item which will be set or reduce the value of the parameter Tilt the PTZ downward Confirm Open Confirm the setting of parameters open the aperture Return Close Return or cancel while setting parameters of the menu close the aperture Near focus Focus the image nearby Far focus Focus the image faraway TELE zoom in the image WIDE zoom out the ima
6. the serial number of the cable tester kit Data monitor 5 Data Monitor Port 485 Baud 4800 Captures the protocol from the controlling system and display AD 00 00 O8 OO 40 AF 47 AO 00 00 d OO OO AF OF e id od Sa RE 2 command data It is helpful to debug and maintain RS485 04 40 00 AF AB oS zin Ar OF communication 0U OO AF Device setting 6 Device setting Set the parameters of the CCTV testerPRO Auto power off Frompt sound Language Keypad tone Language Brightness Address search Brightness Address search Noi saved Enter to apply Ver STPV1 32 Page 11 CCTV testerPRO User s Manual 3 3 PTZ Controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position The following connections should be confirmed before use a The Video In interface of the CCTV testerPRO and the output interface of camera b Data A of the CCTV testerPRO and A of the PTZ camera or controlling device data B of the instrument and B of the PTZ camera or controlling device Note Don t connect communications interface with a circuit the voltage higher than 6V las we en b Cy DA fai w T P JO Oy ay PIZ controller a Press SET key to enter the sub menu of PTZ controller RS485 Ay ewe Baud 2400 b Press the L YJ key to select the para
7. 34 Video selling A eea 15 ge GOlOrDar generator sr sele ts Ken ASSR teeta ae AN ee 15 00 CADIC ESIE mrii ERNE DE EOS BE EEG e 16 3 7 Data monhor i asenet 16 nO DEVICE SElinGessr ensete HEDDER GENESIS EEN NEUES nee eneen adsense 17 Ver STPV 1 32 CCTV testerPRO User s Manual 3 9 Address search 18 3 10 Digital multimeter 19 3 11 Optical Power Meter 26 4 DC12V Power output 2220 22 27 5 Audio input TESl r r rrersennesensernennentenentneendenndenetennnnnennanendennteedennsnenennnernnnntee 27 6 Specifications 28 6 1 General specificationS 28 6 2 Multimeter specifications 29 1 Safety Information Notice m The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital gas station etc m To prevent the functional decline or failure the product should not be spr
8. C12V 1A power to the power input port of the CCTV tester to avoid destroy c When the requirement of the camera is higher than 1A the CCTV tester will enter protection mode Disconnect all the connections of the CCTV tester and then connect the CCTV tester with power adaptor to resume the CCTV tester 5 Audio input test Test the audio input from pickup devices Connect the tester and pickup device with the audio cable ec i km dl meg AUDIO IN wA Ver STPV 1 32 Page 27 CCTV testerPRO User s Manual 4 Specifications 4 1 General Specifications Display LCD adjustment Video IN OUT Video Output Mode 1 0 Vp p Communication Compatible with more than 20 protocols such as PELCO D P Samsung PTZ Protocol Ni Panasonic Lilin Yaan etc Baud Rate 150 300 600 1200 2400 4800 9600 19200bps Video Signal Generation i Output one channel PAL NTSC colorbar video signal for testing Color bar generation i monitor or video cable Digital multimeter Vol rrent resistance and capacitance measuring continuit Multimeter OM AGE GE p 9 y testing diode testing UTP CABLE TEST Test UTP cable connection status and display in the screen Read UTP cable test the number of the test box DCI2V power output Audio input test test the pickup and other audio equipments on the front end Page 28 Ver STPV1 32 CCTV testerPRO User s Manual Rechargeable After charging 3 4 hour working time lasts 12 hours Low Co
9. Mi B Qtech Electronics Co Ltd B tech www b gtech com Email sales b qtech com bgshelly gmail com USER S MANUAL CCTV TesterPro Stest 895 Ver STPV1 32 2009 5 Ms Shelly Yoe GM MSN bgshelly hotmail com Skype bgshelly Tel 0086 755 25852163 0086 15994792003 CCTV testerPRO User s Manual m Thank you for purchasing the CCTV security tester Please read the manual before using the CCTV testerPRO and use properly m For using the CCTV testerPRO safely please first read the Safety Information carefully in the manual m The manual should be kept well in case of reference m Keep the S N label for after sale service within warranty period Product without S N label will be charged for repair service m If there is any question or problem while using the CCTV testerPRO or damages occurred on the product please contact our technical Department Table of Content 1 Safety Information etende tet see eee eee ie as et eneen done ESS 3 2 PVE PO UC U1 0 Oreste nee dri rnin a 4 2 1 Features rr rsransrnanssansneretenansetenn serene aaia 4 2 2 GOTY testet PRO KMS weerde edaktie aE 5 20 FONE PANE Korie 6 2 4 olde VIEW ianea eaaa 8 2 9 INStaNIng the Balteny sai e e ended 9 o COST AU Osc a a eenen 10 3 1 Power Om Ofl s n ssrtenssnsennnssenansensntenendseneens entend senen seatdensnbeneadennanasshannaneraass 10 One Menu amp FUNCHONS tenten ttenen teen ett e SEES SE RS SES KEDE SS LEDEDES 10 3 9 PTZCONUOISE ainiin 12
10. ck b Press p G to select enter the diode testing c Connect test leads across to the anode the black lead to the cathode of the diode under testing Page 24 Ver STPV 1 32 CCTV testerPRO User s Manual d You can get reading from LCD NOTE The meter will show approximate forward voltage drop of the diode Ifthe lead connection is reversed only figure OL will be display H Capacitance Measuring WARNING To avoid electric shock be sure the capacitors have been discharged fully before measuring the capacitance of a capacitor a Connect the black test lead to the COM jack and the red test lead to the jack L_ gt b Press p G to select T enter the capacitance measurement Auto range by press key and Manual range by press SA oO Manual range 0 000nF 6 6nF range 00 00nF 66nF range 000 0nF 660nF range 00 00uF 66uF range 000 0uF gt gt En 0 000uF gt 6 6uF range gt gt 660uF range 5 0 000mF 6 6mF range 00 00mF gt 66mF range c Before connect test leads across two sides of the capacitor under measurement be sure that the capacitor has been discharged fully d You can get reading from LCD Ver STPV1 32 Page 25 CCTV testerPRO User s Manual 3 11 Optical power meter PT cantral ler Optical power meter 70 00 dBm Colorbar generator Cable tester Data monitor Jevice setti 347 Den ett ing 1270nm Address search Digital multimete
11. ge Digital multimeter Ver STPV1 32 Page 7 CCTV testerPRO User s Manual 2 4 Side view LSaLa18 3 din 28 Right Side Left Side Top View Page 8 Ver STPV1 32 CCTV testerPRO User s Manual 2 5 Installing the Battery The tester has built in lithium ion polymer rechargeable battery The battery cable inside battery cabin should be disconnected for safety during transportation gt TS Prior to the use of the instrument the battery cables inside the battery cabin should be well connected m Usually it need not to disconnect the cable at the normal use pressing key continuously can power on or off the tester At the first time of use the batteries should be completely exhausted and then recharged for 4 or 5 hours yy The Charge Indicator lights red when charging the battery The charge indicator turns off automatically when the charging is completed A Notice When the Charge Indicator turns off the battery is approximately 90 charged The charging time can be extended for about hour and the charging time within 8 hours will not damage the battery A The tester can work as usual while it is being charged however But the charging time will be extended Press the RESET key at the right of the instrument to restore the default settings when the instrument works abnormally Ver STPV1 32 Page 9 CCTV testerPRO User s Manual 3 Operation 3 1 Power on Continuously press at least 2 seconds to p
12. imum current of 10A socket is 10A over current will destroy the meter and will damage the operator D AC Current Measuring WARNING Shut down the power of the tested circuit then connect the meter with the circuit for measurement a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack b Press p CE to select enter the AC current measurement Manual range by press SAN only manual range supply Page 22 Ver STPV1 32 CCTV testerPRO User s Manual Manual range 0 000mA gt 6 6mA range 00 00mA gt 66mA range 000 0mA gt 660mA range 00 00A gt 10A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates overrange situation and the higher range has to be selected When the value scale to be measured is unknown beforehand set the range selector at the highest position The maximum current of mA socket is 660mA over current will destroy the fuse and will damage the meter The maximum current of 10A socket is 10A over current will destroy the meter and will damage the operator E Resistance Measuring WARNING When measuring in circuit resistance be sure the circuit under test has all power removed and that all capacitors have discharged fully
13. inkled or damped m The exposed part of the tester should not be touched by the dust and liquid m During transportation and use it is highly recommended to avoid the violent collision and vibration of the tester lest damaging components and causing failure m Don t leave the tester alone while charging and recharging If the battery 1s found severely hot the tester should be powered off from the electric source at once The test should not be charged over 8 hours B Don t use the tester where the humidity is high Once the tester is damp power off immediately and move away other cables connected m The tester should not be use in the environment with the flammable gas m Do not disassembly the instrument since no component inside can be repaired by the user If the disassembly is necessary indeed please contact with the technician of our company m The instrument should not be used under the environment with strong electromagnetic interference m Don t touch the tester with wet hands or waterish things m Don t use the detergent to clean and the dry cloth is suggested to use If the dirt is not easy to remove the soft cloth with water or neutral detergent can be used but the cloth should be tweaked sufficiently About digital multimeter m Before using you must select the right input jack function and range m Never exceed the protection limit values indicated in specifications for each range of measurement Page 2 Ver
14. k when measuring high voltage a Connect the black test lead to the COM jack and the red test lead to the V jack al e b Press p G to select U enter the DC voltage measurement Auto range by press key and Manual range by press SA or Manual range 0 000V gt 6 6V range 00 00V gt 66V range 000 0V gt 660V range 000 OmV gt 660mV range c Connect test leads across the source or load under measurement d You can get reading from LCD The polarity of the red lead connection will be indicated along with the voltage value NOTE When only the figure OL is displayed it indicates over range situation and the higher range has to be selected When the value scale to be measured is unknown beforehand set the range selector at the highest position Page 20 Ver STPV1 32 CCTV testerPRO User s Manual B AC Voltage Measuring WARNING You can t input the voltage which more than 660V AC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shock when measuring high voltage a Connect the black test lead to the COM jack and the red test lead to the V jack b Press p G to select U enter the AC voltage measurement Auto range by press key and Manual range by press RAN Manual range 0 000V gt 6 6V range 00 00V gt 66V range 000 0V gt 660V range 000 OmV gt 660mV range c Connect test leads across the source or load under
15. ll preset 33 Open Auto flip function Call preset 34 Reset zero point of PTZ camera Call preset 64 Enter the main menu of the PTZ camera Call preset 95 Enter the main menu of the PTZ camera or stop the PATTERN recording Call preset 96 Run pattern 1 Call preset 97 Run preset tour 1 Call preset 98 Run frame Scan Call preset 99 Run Auto scan Go PS EE 098 Go PS em 099 SE Page 14 Ver STPV1 32 Kun Frame scanning Call the preset point 098 Run Auto scanning Call the preset point 099 CCTV testerPRO User s Manual 3 4 Video Setting User can customize the brightness contrast and saturation of the LCD according to the using environment and display the format PAL NTSC of video input Contrast Saturation a Press the 4 or Lv key to select the parameter which we want to change the value b Press the a or e key to change the value Press ENTER key to save the change or press RETUR key to give up the change c The Video Format and Video Level will be displayed in the lower portion of the screen If there is no video signal at the Video IN port of the CCTV TesterPRO the type of NTSC or PAL and Video Level will not be displayed Depending on the type of camera connected to the CCTV testerPRO the Video Format will automatically change between NTSC and PAL and the Video Level will automatically change between IRE Institute of Radio Engineers and mV NTSC signals measu
16. measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates over range situation and the higher range has to be selected When the value scale to be measured is unknown beforehand set the range selector at the highest position C DC Current Measuring WARNING Shut down the power of the tested circuit then connect the meter with the circuit for measurement a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack Ver STPV1 32 Page 21 CCTV testerPRO User s Manual b Press p G to select A enter the DC current measurement Manual range by press es only manual range supply Manual range 0 000mA gt 6 6mA range 00 00mA gt 66mA range 000 0mA gt 660mA range 00 00A gt 10A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD The polarity of the red lead connection will be indicated along with the voltage value NOTE When only the figure OL is displayed it indicates overrange situation and the higher range has to be selected When the value scale to be measured is unknown beforehand set the range selector at the highest position The maximum current of mA socket is 660mA over current will destroy the fuse and will damage the meter The max
17. meter Address Pan speed which we want to change the value Tiltspeed Set PS Get PS c Press ENTER key to save the change or press RETURN key to give up the change d Press SET key to exit the sub menu e Press POWER key to full screen the image Page 12 Ver STPV1 32 CCTV testerPRO User s Manual A Protocol Select the protocol according to the protocol of the PTZ camera Up to 21 popular protocols are available like elco P Pelco D Samsung Yaan LiLin CSR600 etc B Port Select the communication port for the PTZ camera controlling RS232 422 485 C Baud Select the baudrate according to baudrate of the PTZ camera 150 300 19200bps D Address Set the ID according the ID of PTZ camera 0 254 E Pan Speed Set the pan speed of PTZ camera 0 63 F TiltSpeed Set the tilt speed of PTZ camera 0 63 G Set PS Setup preset position 0 128 a P T Z the camera to desired position b Press SET key to enter PTZ controller submenu c Move the yellow cursor to Set PS and then press En or gt key to select the preset position number d Press ENTER key to complete preset position setting or preset RETURN key to give up preset position setting Tips Press gt or En key to accelerate the value changing H Go PS Call the preset position 0 128 The PTZ camera will go to the desired preset position a Move the yellow cursor to Go PS and then press Ka or gt key to select the preset po
18. nsumption Energy saving technology Working 30 C 70 C Temperature Working Humidity 30 90 Dimension Weight 176mmx94mmx36mm 340g 4 2 Multimeter specifications Counts 6600 6600 Conversion rate 3 times s Current modes for clamp meter with ZERO function DC Voltage 660mV Manual range 0 1mV 6 6V 660V AC Voltage 660mV Manual range 1 5 6 DC Current 6 6mA 0 5 3 Ver STPV1 32 Page 29 CCTV testerPRO User s Manual AC Current 6 6mA 660mA 100uA Resistance 6 6KQ 660KQ 6 6MQ 66MQ C1 2 5 10KQ Continuity Built in buzzer will sound if resistance is lower than 50 Q Diode Display read approximate forward voltage ofdiode Page 30 Ver STPV 1 32 CCTV testerPRO User s Manual Capacitance 660nF 3 5 8 6 6uF 660uF 100nF 4 3 Optical power meter specifications Measure Range dBm 70 10dBm 50 26dBm Calibrated Points nm 850nm 980nm 1310nm 1480nm 1550nm Display Resolution Linear 0 1 Nonlinear 0 01dBm Operating Temperature C 10 50 Storage Temperature C 20 70 The data above is only for reference and any change of them will not be informed in advance For more detailed technical inquiries please feel free to call the Technical Department of our CE FE Ver STPV1 32 Page 31 company
19. o Device setting menu m Prompt sound Language Brighiness Press key to confirm after change Address search to on which add address scan sub menu Press to switch the sub menu as illustrated Note The system returns to OFF after shutdown and the Proteco scan sub menu closes automatically Set ON again for next Port Baud use Address Press ser key to set protocol communication port communication rate make them same as the PTZ camera Press on rar key the address values is constantly on the rise or decrease NEAR The tester will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key to stop searching up FAR The tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop searching up WIDE The tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning FAR The tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will stop panning Page 18 Ver STPV1 32 CCTV testerPRO User s Manual Press button the tester will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key t
20. o stop searching up Press rete manual single step decreasing button the tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will stop panning Press button the tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop searching up Press manual single step incremental button the tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning Press the direction control button to adjust Speed Dome Camera press button to quit from the address scanning function menu 3 10 Digital Multimeter Video sening De 0 000 V Lolorbar generator Cable tester Auto Data moniter Device sett d Function Y Range 1 Function Button Auto range Data hold Relative measuring p Function select SAN Manual range 2 SYMBOLS U DC Voltage Measuring U AC Voltage Measuring A DC Current Measuring A AC Current Measuring Q Resistance Measuring d Continuity Testing Diode Testing F Capacitance Measuring Ver STPV 1 32 Page 19 CCTV testerPRO User s Manual 3 OPERATING INSTRUCTION A DC Voltage Measuring WARNING You can t input the voltage which more than 660V DC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shoc
21. ower on off the CCTV testerPRO When the CCTV testerPRO is powered on press MODE key the main menu will pop up PTZ controller PTZ controller VOGO Seni i Lolorbar generator Cable tester Data monitor NO video input 3 2 Menu amp Functions Press MODE key continuously or press the J key to select the function PTZ controller Video settings Colorbar generator LAN cable tester Data monitors Device setting and enter corresponding function setting sub menu Press SET key to set the parameters in function sub menu Note When the CCTV testerPRO is powered on it will return to the function which is being operated before it is turned off PTZ controller 1 PTZ controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position Part Baud Address Fan Speed Tilt Speed Set PS Go PS Page 10 Ver STPV1 32 CCTV testerPRO User s Manual 2 Video setting Adjust the LCD brightness Contrast Color saturation Contrast Saturation i Video Format and Video level testing 3 Colorbar generator Output or receive seven different forms of video color bar to tester monitor cable or other equipment 4 Cable tester Test LAN cable or telephone cable The connecting condition and the sequence of wires will be displayed as well as
22. r Wavelength av mW dBm 1 Function Button Data hold Relative measuring p Wavelength select NAILIN mW dBm units select 2 OPERATING INSTRUCTION A Press MODE key to select Optical power meter B Absolute power value measurement 1 Set the wavelength via p G key the default wavelength is 1310nm 2 Input the optical fiber to be measured the power value is displayed in LCD 3 Linear and nonlinear value of the current optical fiber power can be displayed by pressing RAN key to change the unit to be mW or dBm C Relative power value optical link loss measurement 1 Set the wavelength for measurement 2 Measure the first optical fiber pressing the key under any display unit then the current fiber power value is stored as the base reference value 3 Input another optical fiber to be measured the relative power value is displayed The optical power meter displays the end end loss of the fiber under test the unit of loss value must be dB Page 26 Ver STPV1 32 CCTV testerPRO User s Manual 4 DC12V 1A power output Power the camera with DC12V 1A power output from the tester It is helpful for demo and testing where there is no power supply available Y VIDEO IN c VIDEO OUT z pn ze fa o om DC AVA Se OUTPUT hac aaa Es i Notice a Don t input any power into the DC12 1A OUTPUT port of the CCTV tester to avoid destroy b Don t output this D
23. red in IRE units PAL signals measured in mV The Video Level should be within the indicated range Levels that are too low will result in a dim picture with reduced dynamic range A Video Level that is too high will result in washed out pictures with decreased The CCTV testerPRO will display Normal when video levels are 1000mV 20 Exceed or Weak will be displayed when video level out of 1000mV 20 3 5 Colorbar generator Output video at any mode Output or receive seven different forms of video color bar to test monitor video cable or other equipment Colorhar Generar Ver STPV1 32 Page 15 CCTV testerPRO User s Manual a Press the L2 pel key to select the parameter which we want to change the value b Press the key to change the value c Press ENTER key to save the change or press RETURN key to give up the change 3 6 Cable Tester Test LAN cable or telephone cable Connect LAN cable or telephone cable with the CCTV testerPRO and cable tester And then the connecting status cable type and the sequence of wires will be displayed as well as the serial number of the cable tester kit ssed ethernet Straight through Line Cross Line 3 7 Data monitor Capture the command data from RS485 controlling system gende Es a Connect the RS485 or RS232 interface of controlling system Pa F 47 F OF F SF F OF F 4B F OF F 4D F OF with the RS485 or RS232 interface of the
24. sition number b Press ENTER key to complete preset position calling or preset RETURN key to give up preset position calling Tips Press gt or lt key to accelerate the value changing The way of calling the OSD menu and preset of the PTZ camera may vary with control systems from different manufacturers Please read the operation manual of control system manufacturer for details The way of calling OSD provided for reference is calling preset 64 a Move the yellow cursor to PTZ controller to enter PTZ controller mode b Press SET key to enter PTZ controller sub menu Press A or Lv key to move the yellow cursor to Go PS Ver STPV1 32 Page 13 CCTV testerPRO User s Manual C Press lt or gt key to select the preset number 64 and then press ENTER key to call OSD menu of the PTZ controller Go PS 4 064 OSD Menu of Dome For reference only MAIN MENU DISPLAY SETUP CAMERA SETUP CONTROL SETUP CAMERA MASK SET PROGRAM PAL CAMERA CAM DEFAULT SET DOME RESET EXIT O oo A DB A WN OSD menu of dome Call the preset point 064 MAIN MENU Display configuration Set camera parameters Set PTZ controlling Set privacy mask Set auto running functions PAL NTSC Switch Restore the default settings Reset the dome Exit the main menu B Operate auto running functions by calling preset position effective for some brands of PTZ camera Ca
25. tal multimeter voltage current resistance and capacitance can be tested continuity testing diode testing B Optical power meter used for optic fiber CCTV monitor system CATV system optic fiber communication networks deployment and test PTZ control Pan tilts the P T unit zooms in out the lens adjusts the focus aperture and sets and calls the preset position m Video displaying Automatically adapts and displays the video format of NTSC PAL LCD Brightness Contrast Color Saturation are adjustable Ver STPV1 32 Page 3 2 2 Page 4 CCTV testerPRO User s Manual Video Generating The PAL NTSC multi system colorbar video generator seven system switchable transmit receive seven system colorful imagines Data analyst Captures and analyzes RS485 controlling data to help the technician to find out the problem Cable testing It is powerful in testing LAN cable measuring the connecting status displaying the sequence of connection and the NO of the LAN cable Multi interface and Multi baud rate Support RS232 RS485 and RS422 interface baud rate ranging from 150 600 to 19200bps Multi protocol Supports more than twenty PTZ protocols For example PELCO P PELCO D SAMSUNG etc PTZ address scanning search up the ID of PTZ camera Lithium Ion Polymer Battery 3 7V DC3000mAh The device employs advanced power control and protection circuit The device is high power efficient energy saving and environmental protection
Download Pdf Manuals
Related Search