Welding Helmet - Paddock Spares
Contents
1. Description Description Helmet Shell Shade Control Knob Front Cover Lens ADF Retaining Frame Headgear Angle Adjusting Knobs Headgear Height Adjusting Pin Headgear Diameter Adjusting Knob www lasertools co uk Trouble Shooting PROBLEM S POSSIBLE CAUSE S SUGGESTED SOLUTION S Difficult to see through Front cover lens dirty Clean or replace front cover lens filter Filter cover lens dirty Clean filter cover lens Filter does not darken Grind Mode Selected Adjust Shade from 9 to 13 when arc is struck Sensors or Solar Panel Make sure sensors or solar panel are blocked exposed to weld arc without blocking Set Sensitivity to LOW Adjust sensitivity to required level Filter darkens without arc Set Sensitivity to HIGH Adjust sensitivity to required level Filter remains dark Set Delay to MAX Adjust sensitivity to required level after welding Our products are designed to be used correctly and with care for the purpose for which they are intended No liability is accepted by the Tool Connection for incorrect use of any of our products and the Tool Connection cannot be held responsible for any damage to personnel property or equipment when using the tools Incorrect use will also invalidate the warranty If applicable the applications database and any instructional information provided has been de2. e 9 to 13 based upon the welding process you will use by consulting the Shade Guide Table The variable shade control knob is mounted to shell for external adjustment The welding helmet can also be used to protect the face when grinding Grind mode prevents filter lens from auto darkening Arc Current Amperes Process 1 5 6 10 15 30 40 60 70 100 125 150 175 200 225 250 300 350 400 450 500 600 nen en eee a ee _ raw dad sdi e d7i 8e Jojon on Jooo K SMAW Covered electrodes amp MAG Metal arc Welding TIG Gas Tungsten Arc Welding K MiIG Heavy MIG with heavy metals K MiG light MIG with light alloys K PAC Plasma jet cutting K PAW Microplasma arc welding Delay Control When welding ceases the viewing window automatically changes from dark back to light but with a pre set delay to compensate The delay time can be set to MIN 0 1 sec or MAM 1 0 sec by infinitely dial knob inside the cartridge The minimum delay suits spot or short welds The maximum delay suits heavy current welding and reduces eye fatigue from the arc Selections between MIN and MAX are suitable for most of indoor and outdoor welding operations Sensitivity Control The sensitivity can be set to LOW or HIGH by using the infinitely dial knob on the back of the cartridge The LOW setting suits excess ambient light or with another welding machine close by The HIGH setting suits low amperage welding and weld
3. ing in areas with low light conditions especially low amperage argon arc welding Selections between LOW and HIGH are suitable for most of indoor and outdoor welding operations Front Cover Lens Replacement Replace the front cover lens if it is damaged cracked scratched pitted or dirty Place your finger or thumb into the recess in the bottom of frame and flex the front cover lens upwards until it releases from one edge Then remove any protective film before installing the new one Inside Cover Lens Replacement Replace the inside cover lens if it is damaged cracked scratched pitted or dirty Place your finger or thumb into the recess as marked below and flex the inside cover lens upwards until it releases from one edge Then remove any protective film before installing the new one A S 7 J r S Recess O1 L J Inside Cover Lens ee i J Cleaning and Storing Keep the sensors solar cell and filter lens clean Clean filter cartridge and helmet shell by using a soapy water solution and soft cloth Do not use solvents or abrasive cleaning detergent Switch the product to Grind Mode and put it in a clean dry location for storage
4. osition while using this helmet Inspect the filter lens frequently and immediately replace any scratched cracked or pitted filter lens or cover lenses e Always wear safety glasses or goggles under the welding helmet and protective clothing to protect your skin from radiation burns and spatter Specifications Dark to Light Time Delay Control Viewing Area Cartridge Size UV IR Protection Light State Grind Mode Dark State Sensitivity Control Power Supply Power On Off TIG AMP Rating Operating Temperature Storing Temperature Compliance Headgear Adjustment 1 Adjust the headgear diameter with the twist knob on the back The knob is locked until pushed in Once unlocked twist clockwise to tighten and counterclockwise to loosen 2 Adjust the height by snapping the pin into the hole to lock securely in place 3 To adjust the viewing angle loosen the knob and push the helmet forward and back to the desired tilt position Once the angle is correct tighten the knobs until snug The helmet should still swing up but it should not drift downward when in place for welding 4 To adjust the distance between the user s face and ADF loosen the outside tension knobs to allow for headgear to be repositioned to a different location This should be done one side at a time and both sides should be located the same for proper auto darkening filter operation Shade Control Grind Mode Select the shad
5. signed to offer general guidance for a particular tool s use and while all attention is given to the accuracy of the data no project should be attempted without referring first to the manufacturer s technical documentation workshop or instruction manual or the use of a recognised authority such as Autodata It is our policy to continually improve our products and thus we reserve the right to alter specifications and components without prior notice It is the responsibility of the user to ensure the suitability of the tools and 9 018541060947 gt Guarantee If this product fails through faulty materials or workmanship contact our service department direct on 44 0 1926 818186 Normal wear and tear are excluded as are consumable items and abuse Distributed by The Tool Connection Ltd TA TOOL sects l l l a CONNECTION Kineton Road Southam Warwickshire CV47 ODR T 44 0 1926 815000 F 44 0 1926 815888 info toolconnection co uk www toolconnection co uk www lasertools co uk www lasertools co uk Safety ARC Rays can injure eyes and burn skin e Before welding always inspect helmet and auto ig darkening filter ADF to be oe sure they are fitted properly E and in good condition D e Keep the sensors solar cell and filter lens clean Clean the filter cartridge using a soapy water solution and soft cloth Do not use solvents or abrasive cleaning detergent Do not weld in the overhead p
Download Pdf Manuals
Related Search