For your own safety, please read this user manual carefully before
Contents
1. Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually 2 V1200W V1 0 01NR A CAUTION Never touch the device during operation The housing may heat up A CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES y y y This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual the device was designed for indoor use only Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device While2. E v E 9 V1200W V1 0 01NR Reset Reset Scan Reset Colors Reset Shutter Reset Others Lamp adjustment Reset function Wheel adjustment Effect Adjust User mode Preset User mode User s Mode Set Select Programs Edit program Auto scenes Rec Edit Program Function Mode address setting PAN Moving PAN Moving Save Active Color wheel Save and run User A seetings User B settings User C settings PAN Save and run Program 1 Program 10 Program 1 Program 10 Edit Scene 001 Edit Scene 250 XX XX PAN Moving XXX Please wait Color wheel XXX Please wait PAN CH NO 01 Please wait Program Test Start step End step Input by outside Save and Active Scene Time Pan Tilt STEP Start step xxx End step xxx TIME XX XS Pan xxx With this function you can adjust the desired DMX address via the Control Board Select Set DMX address via the encoder Press the encoder adjust the DMX address by turning the encoder Press the encoder to confirm Press the Mode Esc button in order return to the main menu Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel The display automatically shows the channel with a value changing Slave setting With this function you can define the device as slave Auto Program Reset all motors Re
3. data is received or not If the data is received the the display will show A 001 with the actually set address If there is no data received at the DMX input the display will flash A001 with the actually set address This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the device the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link 2 If the lamp is on the display will show 1 with the actually set address If the lamp is off the the display will show A001 with the actually set address Control Board The Control Board offers several features you can simply set the starting address switch on and off the lamp run the pre programmed program or make a reset The main menu is accessed by pressing the Mode Esc button until the display 15 lit Browse through the menu by turning the encoder Press the encoder in order to select the desired menu You can change the selection by turning the encoder Press the encoder in order to confirm You can leave every mode by pressing the Mode Esc button The functions provided are described in the following sections 8 V1200W V1 0 01NR Default settings shaded Main menu
4. OFF if you don t Lamp on at temp With this function you can set the inside temperature from which the projector will restrike the lamp after automatic lamp shutoff Lamp off at temp With this function you can set the inside temperature at which the projector will automatically switch the lamp off Turn the encoder to select the maximum inside temperature betwwen 60 C an d159 C Inside temperatures below 90 C are 12 V1200W V1 0 01NR not critical 90 C and more should lead to the lamp being switched off Please note that the outside temperature should not exceed 45 C Display set Display close time With this function you can shut off the LED display after 2 to 59 minutes Turn the encoder in order to select the desired shut off time Display intensity Whth this function you can adjust the display intensity from 20 to 99 Turn the encoder in order to select the desired intensity gt Init effect With this function you can adjust with which value the respective channels will start Mic sen sitivity With this function you can select the desired microphone sensitivity between 0 and 99 94 gt Restore factory settings With this function you can restore the factory settings of the device All settings will be set back to the default values shaded Any edited scenes will be lost Reset functions With this function you can Reset the device via the Control Board You can select the different Resetfunctions by
5. Submenu Dipy Foncion Set DMX address 1 1 Function LWauedisplay DMX value Mode Slave setting O Auto program Music control Power on time XXXX Individual fixture pue ieee E PO Product Info Unit model Unicode Unit code Company WEB Company WEB CompanyTel ___ Tel Software version ICOI Ver 1 0 Software version of ICXX Ver 9 9 each IC Effect Set Pan Reverse Reverse movement Reverse movement Tilt Reverse ul Blackout moving Blackout while Blackout colors PAN TILT moving or Scan fine select color wheel moving Status choose Addr set online IN OFF Add via DMX Master or Alone Master Alone Master Alone switch Auto if no DMX Auto run if no DMX Music if no DMX Music contr DMX Lamp control Lamp on or off Lamp on off Lamp on by power on Lamp on off Power Lamp on via DMX Lamp on via DMX Lamp off via DMX Lamp off via DMX Lamp off if no DMX Lamp off if no DMX Lamp on at temp Lamp restart at temp Lamp off at temp Lamp off at temp Auto Fans Speed Fans Speed Adjust Display set Display close time 05 M 02 59 Display shutoff time Display intensity 20 99 LCD brightness Init effect PAN Moving PAN Moving XXX Initial effect position Save and run Please wait Mic sensitivity 0 99 Sensitivity of Mic Ph SB wu
6. Triton e Blu PROFESSIONAL MOVING HEAD USER S MANUAL V1200W KEEP THIS MANUAL FOR FUTURE NEEDS For your own safety please read this user manual carefully before installing the device CAUTION amp K eep this device away from rain and moisture OD Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow carefully the instructions of this manual INTRODUCTION Thank you for having chosen this professional moving head You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find the fixture device a power cable an XLR connection cable a safety cable and this manual Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device Features e Pan 540 tilt 265 e Colors e Color wheel 1 with 4 correction filter Color wheel 2 with 4 discrete dichroic filters The color wheel 2 can be individually equipped with colours gobos e CMY colour mixture for indefinite colour variations e Rainbow effect with adjustable speed in both directions e Variable colour temperature correction via CTO filter e Strobe effect 1 13 flashes per second or random strobe e Stepless zoom e Automatic progr
7. am e Display digital address and function setting e High speed pan amp tilt movements e Control board with LCD display and encoder for adjusting the DMX starting address Pan Tilt Reverse program reset lamp on off operating hours e Lamp switches ON OFF locally e Auto test for all functions e Value of each DMX channel can be displayed 1 V1200W V1 0 01NR SAFETY INSTRUCTIONS CAUTION Be very careful during installation Since you will be working with a dangerous voltage you can suffer a life threatening electric shock when touching live wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual IMPORTANT D amages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person Make sure that the available voltage is not higher than stated at the end of this manual
8. am 1 Channel 16 Pan fine 16bit Channel 17 Tilt fine 16bit ERROR MESSAGE When you turn on the fixture it will make a reset first The display may show while there are problems with one or more channels stands for channel 1 2 3 5 6 7 who has the testing sensor for positioning For example when the display shows 02 it means there is some error in channel 2 If there are some errors on channel 1 channel 2 channel 5 at the same time you may see the error message 02Er 05Er flash repeated for 5 times and then the fixture will generate a reset signal all the stepper reset If the fixture remain error message 16 V1200W V1 0 01NR after performing reset more than 3 times it will detect whether the fixture has more than 3 errors If the fixture has more than 3 errors including 3 errors all the channels can not work properly but if the fixture has less than 3 errors only the channels which have errors can not work properly others can work as usual O1Er Cyan Color error This message will appear after the reset of the fixture and if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective The cyan color is not located in the default position after the reset 02 Magenta Color error This message will appear after the reset of fixture if magnetic indexing circuit malfunction sensor failed or magnet missin
9. choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 1 meter Always fix the fixture with an appropriate safety cable if you use the clamp to hang up the fixture When fixing the device on a raised from the ground support be sure to use no less than screws and nuts of M10 x 25 mm and insert them in the pre arranged screw holes in the base of the fixture VN If you use the quick lock cam in hanging up the fixture please make sure the 4 quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc 3 V1200W V1 0 01NR INSTALLATION INSTRUCTIONS a Installing or replacing the lamp Do not install lamps with a higher wattage They generate higher temperature
10. ement With this function you can switch the DMX function Blackout with Pan Tilt movement DM X channel 3 values 226 235 on or off 11 V1200W V1 0 01NR Blackout with colors With this function you can switch the DMX function Blackout with colour change DMX channel 3 values 236 245 on or off Status choose Address set online With this function you can adjust the desired DMX address via an external controller Select Address set online by turning the encoder Press the encoder the display shows ON or OFF Turn the encoder to select if you wish to enable this function or OFF if you don t Press the encoder to confirm Press the Mode Esc button in order to return to the main menu On the controller set the DMX value of channel 1 to 7 Set the DMX value of channel 2 to 7 or 8 When set to 7 you can adjust the starting address between 1 and 255 When set to 8 you can adjust the starting address between 256 and 511 Set the DMX value of channel 3 to the desired starting address If you want to set the starting address to 57 set channel 1 to 7 channel 2 to 7 and channel 3 to 57 If you want to set the starting address to 420 set channel 1 to 7 channel 2 to 8 and channel 3 to 164 256 164 420 Wait for approx 20 seconds and the unit will carry out a reset After that the new starting address is set Master or Alone Whth this function you can set the status of
11. f the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its drive circuit on the main PCB The color wheel 1 is not located in the default position after the reset 09Er Color wheel 2 error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its drive circuit on the main PCB The color wheel 2 is not located in the default position after the reset 12Er Zoom error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Zoom is not located in the default position after the reset CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 17 V1200W V1 0 01NR 1 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 2 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the insta
12. g or the stepping motor is defective or its driver circuit on the main PCB The magenta color is not located in the default position after the reset 03Er Yellow Color error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The yellow color is not located in the default position after the reset 04 Color error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The CTO color is not located in the default position after the reset 05 PAN movement error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The PAN is not located in the default position after the reset 06 TILT movement error This message will appear after the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor 15 defective or its driving IC on the main PCB The TILT head is not located in the default position after the reset 08Er Color wheel 1 error This message will appear after the reset o
13. k fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw DMX 512 control connection 6 V1200W V1 0 01NR Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX Ausgang DMX Eingang DMX Ausgang DMX Eingang XLR Einbaubuchse XLR Einbaustecker XLR Einbaubuchse XLR Einbaustecker 1 Gnd sia 2 Signal 2 Signal 3 Signal 3 Signal 4 NA 5 DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below CONTROLLER Address 35 Address 18 Address 1 Projector DMX start address selection All fixtures shou
14. l 13 Speed Of CMY And Dimmer 0 255 Channel 14 Colour macros CMY and colour wheel 0 7 8 15 16 23 24 31 32 39 40 47 48 55 Speed Max gt OFF 1 Macro2 Macro3 Macro4 5 1 128 135 16 136 143 144 151 152 159 160 167 168 175 176 183 17 18 19 20 Macro21 Macro22 V1200W V1 0 01NR 56 63 Macro 184 191 Macro23 64 71 Macro8 192 199 Macro24 72 79 Macro9 200 207 Macro25 80 87 Macroi0 208 215 Macro26 88 95 Macrot1 216 223 27 96 103 Macro12 224 231 28 104 111 Macro13 232 239 29 112 119 14 240 247 Macro30 120 127 Macro15 248 255 Random CMY Channel 15 Lamp on off reset internal programs 0 19 colour change normal 20 39 colour change to any position 40 59 Lamp on 60 79 Lamp switch off 80 84 All motor reset 85 87 Scan motor reset 88 90 Colors motor reset 91 93 Gobo motor reset 94 96 Shutter amp Dimmer motor reset 97 99 Other motor reset 100 119 Internal program 1 secne1 8 of EEPROM secne9 16 of EEPROM secne17 24 of EEPROM secne25 32 of EEPROM secne33 40 of EEPROM 120 139 Internal program 2 140 159 Internal program 3 160 179 Internal program 4 180 199 Internal program 5 a 1 200 219 Internal program 6 secne41 48 of EEPROM 220 239 Internal program 7 secne49 56 of EEPROM 240 255 Music Control secne of Progr
15. ld be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device You can set the same starting address for all fixtures or a group of fixtures or make different address 7 V1200W V1 0 01NR for each fixture individually If you set the same address all the units will start to listen to the same control signal from the same channel number In other words changing the settings of one channel will affect all the fixtures simultaneously If you set a different address each unit will start to listen to the channel number you have set based on the quantity of control channels of the unit That means changing the settings of one channel will affect only the selected fixture In the case of the spot head which is a 17 channel fixture you should set the starting address of the first unit to 1 the second unit to 18 17 1 the third to 35 18 17 and so on Note The modes of DMX 512 data and lamp are shown via the display A UD DMX OK NO DMX NO DMX Lamp on Lamp on Lamp off Lamp off 1 After switching on the device will automatically detect whether DMX 512
16. llation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed oD CAUTION Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the lamp Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer TECHNICAL SPECIFICATIONS Power supply 208VAC 50Hz LI220VAC 50Hz 230 50 7 1240 50 7 208V AC 60Hz 220 60 7 L1230VAC 60Hz L1240V AC 60Hz Power consumption max 1500 W Lamp MSR 1200 SA DE Motors 16 micro motors Flight case dimensions 65 x 60 x 72 cm Net weight 58 KGS Gross weight 63 KGS Carton packing Remark errors and omissions for every information given in this manual excepted All information is subject to change without prior notice 18 V1200W V1 0 01NR
17. lor Wheel 0 255 Cyan 0 white 255 100 Cyan Channel2 Magenta Color Wheel 0 255 Magenta 0 white 255 10096 magenta Channel 3 Yellow Color Wheel 0 255 Yellow 0 white 255 100 Yellow Channel4 CTO Color Wheel 0 255 0 white 255 100 Channel 5 _ PAN movement 8bit Channel 6 TILT movement 8bit Channel 7 Speed pan tilt movement 0 225 max to min speed 226 235 blackout by movement 236 245 blackout by all wheel changing 246 255 no function Channel8 Color Wheel 0 24 Open white 25 49 Color 1 50 74 Color 2 75 99 Color3 100 127 Color 4 128 187 Forwards rainbow effect from fast to slow 14 V1200W V1 0 01NR 188 193 194 255 Channel 9 0 24 25 49 50 74 75 99 100 127 128 187 188 193 194 255 No rotation Backwards rainbow effect from slow to fast Color Wheel Open white Color 1 Color 2 Color 3 Color 4 Forwards rainbow effect from fast to slow No rotation Backwards rainbow effect from slow to fast Channel 10 Shutter strobe 0 31 32 63 64 95 96 127 128 159 160 191 192 223 224 255 Shutter closed No function shutter open Strobe effect slow to fast No function shutter open Pulse effect in sequences No function shutter open Random strobe effect slow to fast No function shutter open Channel 11 Dimmer intensity 0 255 Intensity O to 10096 Channel 12 Stepless Zoom 0 255 Zoom adjustment from small to big Channe
18. ning time of the lamp from the last lamp on The display shows XXXX X stands for the number of hours The counter is resetted after turning the lamp off Clear lamp time With this function you can clear the running time of the lamp Please clear the lamp time every time you replace the lamp Select Clear lamp time by turning the encoder Press the encoder the display shows ON or OFF Press the encoder to confirm Press the Mode Esc button in order to return to the main menu gt Temp Info System Temp With this function you can display the temperature in the projector base near LCD display in Celsius Inside head Temp With this function you can display the temperature in the projector head near CM Y filter in Celsius Product Info Within this menu you can find the data concerning the type serial number Internet and phone number Software version With this function you can display the software version of the device Select Software version by turning the encoder Press the encoder the display shows X X stands for the version number e g V 1 0 V 2 6 Turn the encoder in order to read the version of every individual IC Press the Mode Esc button in order to return to the main menu Personality Effect set Pan Reverse With this function you can reverse the Pan movement Tilt Reverse With this function you can reverse the Tilt movement Blackout with mov
19. s are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year AN CAUTION B efore taking into operation for the first time the installation has to be approved by an expert Cautions The effect should be installed outside areas where persons may reach it walk by or be seated CAUTION W hen installing the device make sure there is no highly inflammable material within a distance of min 0 5m Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug 5 V1200W V1 0 01NR installation via the Omega holders 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick loc
20. s than which the device was designed for For the installation you need one MSR 1200 SA DE Procedure 1 Unscrew the 4 screws marked A B C and D on the back of the housing holding the plate where the lamp is underneath 2 Gently pull the socket holder of the lamp housing in the middle 3 Carefully insert the lamp into the socket Please remember there is only one way to insert the lamp Gently slide the lamp and its lamp holder back into place and fasten the 4 screws 4 On the access plate there are 3 small screws marked 1 2 and 3 Which are used to adjust the lamp holder in the lamp housing You can adjust the 3 screws to fine turn the position of the lamp to get the maximum light output as shown below CAUTION Do not operate this device with open cover b Mounting the device 4 V1200W V1 0 01NR AN CAUTION Please consider the EN 60598 2 17 and the other respective national norms during the installation The installation must only be carried out by a qualified person The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture gt The operator has to make sure the safety relating and machine technical installation
21. set only Pan Tilt Reset only colors Reset only shutter and or dimmer Reset other motors Test function Lamp adjustment Wheel adjustment User s mode to change channel numbers Preset User modes Select programs to be run Testing program Program in loop Save and exit Save and automatically return manual scenes edit Automat scenes rec With this function you can run the internal program You can select the desired program under Select program You can set the number of steps under Edit program You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time Music control With this function you can run the internal program sound controlled 10 V1200W V1 0 01NR Information gt Time information Power on time With this function you can display the temporary running time of the device from the last power on The display shows XXXX stands for the number of hours The counter is resetted after turning the device off Machine on time With this function you can display the running time of the device The display shows XX XX stands for the umber of hours Lamp on time With this function you can display the running time of the lamp The display shows XXXX stands for the number of hours Lamp off time With this function you can display the temporary run
22. the internal program run The selection Alone means Stand Alone mode and Master that the device is defined as master gt Lamp control Lamp on off With this function you can switch the lamp on or off via the Control Board Select Lamp on off by turning the encoder Press the encoder the display shows ON OFF Turn the encoder to select ON if you wish to strike the lamp or OFF in order to switch it off Press the encoder to confirm Press the Mode Esc button in order to return to the main menu Lamp on off by power on With this function you can select if the the lamp will be switched on when switching the power on Select ON by turning the encoder if you wish to enable this function or OFF if you don t Lamp on via external controller With this function you can select if you can switch the lamp on via an external controller DMX channel 22 value 64 79 Select ON by turning the encoder if you wish to enable this function or OFF if you don t Lamp off via external controller Whth this function you can select if you can switch the lamp off via an external controller DMX channel 22 value 224 239 Select ON by turning the encoder if you wish to enable this function or OFF if you don t Lamp Off if no DMX With this function you can select to switch off the lamp off automatically if there is no DMX signal Select ON by turning the encoder if you wish to enable this function or
23. turning the encoder Effect Adjust Test function of each channel With this function you can test each channel on its correct function gt Lamp adjustment With this function you can adjust the lamp more easily All effects will be canceled the shutter opens and the dimmer intensity will be set to 100 With the individual functions you can focus the light on a flat surface wall and perform the fine lamp adjustment Wheel adjustment With this function you can calibrate and adjust the effect wheels to their correct positions Users mode set User mode With this function you can create user defined channel orders gt Preset User mode With this function you can adjust the Prest user defined channel order Edit program Select program With this function you can select the program for the Program Run 13 V1200W V1 0 01NR Edit program With this function you can edit the internal programs Edit scenes With this function you can edit the scenes of the internal programs Auto scenes rec The PHS 1200 features an integrated DM X recorder by which you can transmit the programmed scenes from your DMXc controller to the PHS 1200 Adjust the desired scene numbers via the encoder from to When you call up the scenes at your controller they will automatically be transmitted to the PHS 1200 INSTRUCTIONS ON USE DMX channel s functions and their values 17 DMX channels Channel1 Cyan Co
Download Pdf Manuals
Related Search