Home

Incubator User Manual A small number of ordinary eggs can be

1. 5 Place eggs on the setter or moving trays from 1 18 days for chicken Egg s sharp end must point down 6 Transfer the eggs from the setter to the hatching trays when they reach the 19th day Place 2 water pans this time Do not open the incubator door onwards or during hatching time 7 Remove chicks to the brooder 12 hours after hatching or when dry Wet chicks may catch cold when out of the incubator If some of the eggs are late in hatching removal of chicks should be done quickly as possible to prevent chilling of the unhatched eggs If any of the remaining eggs appear hatchable continue running the incubator for 3 to 5 days Four Screen Four Display Automatic Incubator Controller Operation Manual The automatic multi function incubator researched and produced by our company uses the more popular microcomputer based technology using the latest micro electronics technology and new components equiping with the imported digital temperature sensor and France moisture sensitive capacitance humidity sensor which makes this instrument miniaturization intelligent high measure ment accuracy This incubator is stable and reliable time saving labor saving and easy to use It is the ideal incubation equipment for propagation of poultry and rare birds and small and medium sized hatchery Main Technical Index 1 Temperature Measuring Range 0 99 C 2 Temperature Measurement Accuracy 0 1 C 3 Humidity Measurement Range 0 99 RH 4 H
2. display zero Raise hand immediately after hearing Di from the buzzer the controller will automatically restore the fac tory settings Factory Settings Reference temperature 38 0 C reference humidity 60 RH cycle of egg turning 90 minute time of egg turning 180 seconds ventilation cycle 120 minutes ventilation time 30 seconds egg turning state automatic egg turning Please pay attention to the following aspects in use 1 The micro computer controller has been made adjustment for temperature humidity egg turing exhaust etc before leaving factory which meets settings required by incubation Under normal cir cumstances you do not need to set up and may use it by connecting the power supply Factory set tings temperature 38 C humidity 60 RH cycle of egg turning 90 minute time of egg turning 180 seconds ventilation cycle 120 minutes ventilation time 30 seconds egg turning state automatic egg turning 2 If you need only to change the temperature and humidity parameters please refer to Section III in page 2 of this Manual Please do not set up other parameters in order to avoid operation errors which may affect your usage and bring you f unnecessary losses 3 Temperature and humidity sensors are made of high precise and micro molecular materials please do not make the sensor come into contact with the water directly The dust must be regularly cleared on the surface of the sensor or it will affect the
3. Incubator User Manual A small number of ordinary eggs can be used while the operator is still learning the incubation pro cess and the machine s operation The location of the incubator is an important factor to a successful production A stable room temperature between 75 F to 80 F or 24 C to 27 C degrees with fresh air and without drafts or room opening is ideal Room temperatures from 55 F to 90 F 13 C to 32 C are acceptable but good temperature control in the incubator is obtained when the room temperature is held within lesser degrees The back of the incubator where the vents are located should be placed no closer to a wall or barrier than 12 inches 30 cm in order to have free air exchange within the room Avoid areas of strong sunlight or air ducts that could influence the temperature in the incubator Eggs must be fresh and fertile Do not use eggs over 16 days old and best results are obtained if eggs are less than 10 days old Percentage of hatch will drop a little each day during storage Eggs being saved for incubation should be protected from excess heat and cold Ideal storage temperature is 55 F and under moist conditions Air cooled by air conditioners can be too dry for storage Discard small or poorly shaped eggs and any cracked thin or porous shells Set only eggs that are clean and with uniform size Eggs can be candled by lighting a bright bulb through an egg while in a dark room This allows the viewer to see if
4. bumen the embryos is much lighter than vitelline The embryo can touch the egg film easily so we change the location of eggs by automatic egg turner system and then the touch point of embryos and egg film changed That can avoid the conglutination of embryos and egg film The times of turning over once every hour After the 17th day they do not need be turned we can move the hatching egg to borning area of egg incubator 5 Cool eggs The benefit of cooling eggs is to emanate the extra heat and supply enough oxygen for embryos to avoid the accident caused by super temperature and lack of oxygen When we put hatch ing eggs in egg incubator for about 7 days it do not need cool eggs When it come to 8th 12th days we cool eggs once every day When it come to 18th 21st days we can cool eggs once per 4 6 hours Every cooling egg we can cool for 15 20 minutes When cooling we open the door of egg incubator
5. d And then press SET and raise your hand the led will display on the lower side of the controller If you need to change the humidity value please press to adjust untill the required humidity 60 RH shows And then press the keySET the controller will automatically calculate and fill the parameters of temperature and humidity and finally return to normal working state Arbitrary temperature and humidity settings example which may change and automatically generate interval but generally do not use it During normal operation press the key SET and dont raise your hand and then press the key untill display and then raise your hand set up the following parameters Set up over temperature alarm led display as shown in right figure P1 is the over temperaturealarm value the alarm will be given if the temperature reaches this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up over temperature value led display as shown in right figure P2 is the over temperature value the exhaust fan will be started up when the temperature reaches this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up upper limit value of temperature control le
6. d display as shown in right figure P3 is the upper limit of temperature control The heating will stop when the temperature reaches this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up low temperature value led display as shown in right figure P5 is the low temperature value The standby heating will start up when the temperature droppes to this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up insufficient temperature alarm value led display as shown in right figure P6 is the insuff cient temperature alarm value The alarm will be given if the temperature droppes to this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up over humidity alarm led display as shown in right figure P7 is the over humidity alarm value The alarm will be given if the humidity reaches this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up upp
7. ded please press untill it displays the value you required And press OK and then lift your hand to save data and automatically move to the next parameter setting Set up egg turning time led display as shown in right figure F2 is the egg turning time unit sec ond which represents the time of turning eggs if any change is necessary please press untill it dis plays the number you required And press OK and then lift your hand to save data and automatically move to the next parameter setting Set up ventilation interval led display as shown in right figure F3 is the ventilation interval time unit second if any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter settings Set up ventilation time led display as shown in right figure F4 is the ventilation time unit second if any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up temperature calibration led display as shown in right figure F5 is the temperature calibra tion value this parameter may revise the temperature deviation brought about by improper selection of temperature measuring point If any change is needed please press untill it displays the value you required And press OK and then rais
8. e your hand to save data and automatically move into the next parameter setting Number of egg turning led display as shown in right figure F7 is the number of egg turning press the key OK and then raise your hand to return to the normal working state Egg turning and Silencing Description Egg turning Mode Automatic egg turning Turn eggs automatically in accordance with the set egg turning interval and egg turing time turn left gt interval gt turn right gt interval gt turn left alternation of egg turning The number of egg turning will display on the parameter F7 and will be zero if the controller power is cut off In order to ensure normal egg turing please switch to the state of automatic egg turing Manual egg turning Press the key and do not lift your hand the controller will enter into the state of manual egg turing after 2 seconds You re your hand when it is adjusted to the desired location the controller will get into the state of automatic egg turing The computer wil define automatically the direction of egg turning Silencing function when the controller give an alarm press the key and lift your hand to remove the buzzer sound and alarm output but then the alarm indicator lamp still lights up press the key again and raise your hand to restore buzzer sound and alarm output control Restore Factory Settings Press both keys of at the same time for more than three seconds the controller will
9. er limit value of humidity control led display as shown in right figure P8 is the upper limit value of humidity control The humidification will stop when the humidity reaches this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up lower limit value of humidity control led display as shown in right figure P9 is the lower limit of humidity control The humidification will start when the humidity droppes to this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and automatically move into the next parameter setting Set up low humidity alarm value led display as shown in right figure PP is the low humidity alarm The alarm will be given if the humidity droppes to this value If any change is needed please press untill it displays the value you required And press OK and then raise your hand to save data and au tomatically move into the next parameter setting Egg turning and calibration parameter setting During normal operation press the key SET and dont raise your hand and then press the key till dis play and then raise your hand set up the following parameters Set up egg turning interval as shown F1 is two successive egg turning interval unit minute if any change is ned
10. measurement accuracy 4 The manufacturer should only assume the obligation for products selled to users but not undertake users other losses caused by product failure The five hatching conditions for chicken in egg incubator 1 Temperature Temperature is the main condition for embryos When the temperature in egg incu bator is upto 32 40 degrees the embryos can grow We should obey the principle of higher temperture in front period middle temperature in middle period lower temperature in back period The first 7th day is front period the temperature in egg incubator can be 38 38 5 degrees The 8th 14th days is mid dle period the temperature can be 37 5 38 degrees The 15th 21st days is back period the temperature in hatching machine can be 37 37 5 degrees If there are more than two batches in hatching machine we can control the constant temperature 37 8 degrees In the 21st day we can enhance the tempera ture a little to be benefit for hatching out Higher temperature can infect the growth of embryos the higher temperature can discrease the hatching period to increase the dead rate When the temperature in hatching machine come upto 42 degrees the egg will die after 2 3 hours The low temperature can aslo infect the growth the low temperature in egg incubator can delay the hatching period to increase the dead rate In the temperature of lower than 36 degrees the hatching egg will possibly die in shell 2 Humidity The embryos ca
11. n adjust to humidity more widely In the front period the humidity in egg incubator can be 50 70 In the middle period the humidity can be 50 In the back period the humidity can be 70 The humidity condition in hatching machine can benefit the hatching for in the front period the hatching egg need produce amniotic fluid in middle period they need to produce stale and in the back period they are dig shell Higher temperature can infect the growth of embryos and infect the release of the stale to result in big belly long little feather The lower temperature in egg incubator can cause more water in body and short little feather 3 The ventilation Good ventilation condition in egg incubator can support good oxygen condition and help to release the CO2 to ensure the air metabolization and normal physioloy function Bad ventilation in hatching machine can cause the malposition and abnormality of embryos and can even cause die In the front period for the ability of matter metabolization is not so good and the quantity of oxygen is not enough in the back period metabolization is well and there is enough oxygen Af ter 19th day the embryo can use lung to breath When there is contradition between ventilation and constant temperature first we should meet constant temperature and then consider the ventilation 4 Turn eggs The main usage of turning egg is to avoid the conglutination of embryos and egg film The vitelline is lighter than al
12. the eggs are fertile only after seven days of incubation Fertile eggs will be dark and will show the outline of the air sack If the air sack is too large for the stage of incubation then mois ture must be added or reduce moisture if too small This method requires that the operator be obser vant and have sufficient experience to properly judge the air sack The humidity water pan should be cleaned before first use and after each hatch The pan should be filled with warm water and maintained at a level approximately to 1 inch from the top Must read easy steps 1 Test the fan blower upon the arrival of the incubator unit Make sure that the fan blower is work ing at all times when you plug the unit into its power supply Unplug open the back and turn the fan blade manually if its not working Intense vibration from shipping and handling commonly cause fan motor misalignment 2 Heat must be at 37 5 C 100 F average during the incubation period and at a 45 55 relative hu midity during setting and 55 65 relative humidity during hatching Above or a degree lower will not affect the eggs Relative humidity can be measured by the use of a hygrometer 3 Fill 1 water pan with non chlorinated water and place it in front of the heater Adding water space will increase humidity while decreasing the water space decreases the humidity 4 Be sure to unplug the incubator power supply before opening or fixing anything inside the incuba tor
13. umidity Accuracy 3 RH 5 Number of signal output 7 over temperature temperature control insufficient temperature egg left turning egg right turning humidity control alarm 6 The maximum output load current temperature control insufficient temperature lt 8A AC220V over temperature egg left turning egg right turning humidity control alarm lt 1A AC22 7 Number of egg turning the maximum record is 999 times 8 Cycle of egg turning adjustment of 0 999 minutes the factory default is 90 minutes 9 Egg turning time adjustment from 0 to 999 seconds the factory default is 180 seconds 10 Ventilation cycle from 0 to 999 minutes the factory default is 120 minutes 11 Ventilation time from 0 to 999 seconds the factory default is 30 seconds 12 Temperature measurement length About 2 meters Working Condition 1 Working Voltage AC 160V 240V 50HZ 2 Relative Humidity less than 85 RH 3 Environment Temperature 10 C 60 C Temperature and humidity settings instance This method is very simple as long as you set up both points of temperature and humidity others will generate automatically For example a incubation control room needs that the temperature is 38 C humidity is 60 RH During normal working press SET and lift your hand a row of led will display on the lower side of the controller If you need to change the temperature value press to adjust till to display the temperature 38 C you require

Incubator User Manual A small number of ordinary eggs can be

Contents

Download Pdf Manuals

Related Search

Related Contents