Home

User Manual of AP Controller - PLANET Technology Corporation.

1. PLANET Networking amp Communication AP Management Users Manual Wireless AP Controller with 8 Port 802 3at PoE WAPC 1232HP User Manual of WAPC 1232HP Copyright Copyright 2015 by PLANET Technology Corp All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of PLANET PLANET makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not PLANET its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Further PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes All brand and product names mentioned in this manual are trademarks and or registered trademarks of their respective holders Federal Communication Commission Interferenc
2. a Type State Pool Name Name Server ID ID Excluded IP C 192 168 1 151 Automatic Committed viant 192 168 1 100 Pool d 132 168 1 152 Automatic Committed vlan1 192 168 1 100 Statistics Binding Declined IP Figure 2 3 DHCP Server Binding Step 4 Now you can continue to configure the managed AP in the next chapters User Manual of WAPC 1232HP Chapter 3 Configuring the AP Controller This chapter delivers a detailed presentation of AP Controller s functionalities and features under 3 main menus including AP Control AP Monitoring AP Status and AP Maintenance allowing you to manage the AP with ease System OP control AP Search t Device LIST gt SSID Profile 1 AP Control section Radio Profile k 2 43 EDG To discover define and upload the predefined wireless profile by group AP Management AP Group Management AP Monitoring AP status AP Status Summary SSID Summary 2 AP Monitoring AP Status Radio Summary To monitor check and analyze the AP status and survey AP Real Time Traffic the wireless signal surroundings Active Clients Rogue AP List gt 2 ns 515 AP Maintenance TFTP setting 3 AP Maintenance Firmware Upgrade To update the firmware reset the AP and locate the AP Group Firmware Upgrade In its physical position Reset AP ME mt ontrol Figure 3 1 AP Controller Menu User Manual of WAPC 1232HP
3. MAC Address The MAC address of the wireless interface The device description of the AP AP Description This field can be modified through the Setting hyperlink under the sub item General Setting AP MAC Address The MAC address of the AP AP Model The model name of the AP SSID The SSID name of the wireless interface Mode The frequency band of the wireless interface Tx Packet The packets sent to this client 48 User Manual of WAPC 1232HP Rx Packet The packets received by this client Tx Rate The transmit rate of this client RSSI The RSSI value signal strength received by this client Expiry Time s The Expiry Time of the client Jena Check this option to let the system refresh the AP list every 15 seconds automatically Refresh Click Refresh to query or update the current list 5 6 Rogue AP List Go to AP Monitoring AP Status gt Rogue AP List gt 2 4G to check current 2 4GHz rogue APs in the environment Go to AP Monitoring AP Status Rogue AP List 5G to check current 5GHz rogue APs in the environment Rogue AP List 2 4G io ssm Jerma eena ess Tenervoton B 24G SSID 1 1 11b g n mixed mode a8 ff 20 00 14 6c WPA2 PSK vdsltesting EE 11b g mixed mode 00 20 4c 81 96 c1 WPA2 PSK EI 11111111 6 11b g n mixed mode 00 50 18 60 91 88 WPA2 PSK 4 M1F Demo Roem 11 11b g mixed mode 00 30 4 12 34 56 WPA2 PSK ea n mixed model 00 30 4f b3 47 c6 WPA2 PSK 6 Noted 6 fibo n
4. SSID Name SSID Broadcast Security Encryption Client Isolation Edi Port Management 2 O 5GSSID 1 Enabled WPA2 Psk Disabled Link Aggregation VLANs Spanning Tree Multicast Add Mew SSID Profile Figure 4 7 SSID Profile List The page includes the following fields Object Description ID This field represents the numerical order of device This SSID name of the AP SSID Name The length of an SSID should be limited to 32 characters 32 octets normally ASCII letters and digits Select Enable to enable the SSID Broadcasting Select Disable to disable the SSID Broadcasting Broadcast SSID Once disabling the SSID Broadcasting the wireless clients will not be able to see the SSID of the AP Security This field equals the Encryption field of the Security Configuration A This field eguals the Authentication Mode field of the Security Encryption Configuration Client Isolation Displays the setting of the client isolation which is to be configured by enabling it or not to by disabling Edit Click Edit hyperlink to re configure the profile Add New SSID Profile Click the Add New SSID Profile button to create a new SSID profile Apply In the delete field check the profile that you want to delete and click 14 User Manual of WAPC 1232HP Apply to apply the setting Reset Click Reset to cancel the check box of the delete option back to un
5. 2 4GHz Radio Profile List Figure 4 21 AP Group Management 2 4G Wi Fi Setting The page includes the following fields Object Description AP Information AP Group Name The AP group name To edit this field please go back to the AP Member Setting page The description of the AP group AP Group Description To edit this field please go back to the AP Member Setting page 37 User Manual of WAPC 1232HP 2 4GHz SSID Configuration This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz ae SSID 1 To create new SSID profile please go to the SSID Profile page SSID 2 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 2 To create new SSID profile please go to the SSID Profile page SSID 3 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 3 To create new SSID profile please go to the SSID Profile page SSID 4 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 4 To create new SSID profile please go to the SSID Profile page SSID 5 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 5 To create new SSID profile please go to the SSID Profile page 2 4GHz Radio Configuration This field is used to designate the 2 4GHz Radio Profile to the AP s 2 4GHz Radio Profile advanced setting To create new 2 4GHz radio profile please go to Radio Profile gt 2 4G page
6. Apply Click Apply to save and apply the setting Reset Click Reset to erase all settings to default values 4 6 2 5GHz Wi Fi Setting Click the Setting hyperlink under the SGHz Wi Fi Setting field to enter the sub menu of AP Group Management On this page you can designate the AP group to use the specific 5GHz SSID and Radio profiles 38 User Manual of WAPC 1232HP AP 5GHz Wireless ID1Settings AP Group Information SSID 1 SSID 2 SSID 3 SSID4A 4 SSID5 2 Disable Disable wv Jj Figure 4 22 AP Group Management 5G Wi Fi Setting The page includes the following fields Object Description AP Information AP Group Name The AP group name To edit this field please go back to the AP Member Setting page AP Group Description The description of the AP group To edit this field please go back to the AP Member Setting page 5GHz SSID Configuration This field is used to designate the 5GHz SSID Profile to the AP s 5GHz Mu SSID 1 To create new SSID profile please go to the SSID Profile page SSID 2 This field is used to designate the 5GHz SSID Profile to the AP s 5GHz SSID 2 To create new SSID profile please go to the SSID Profile page SSID 3 This field is used to designate the 5GHz SSID Profile to the AP s 5GHz SSID 3 To create new SSID profile please go to the SSID Profile page 39 User Manual of WAPC 1232HP SSID 4 This field is used to designat
7. Refresh Apply Reset Description This field represents the numerical order of device The model name of the AP The IP address of the AP On the Device List page the IP address is a hyperlink which enables the user to link to the AP s Web configuration page directly The MAC address of the AP The device description of the AP User can turn on or let the position LED blink to locate the AP s position Off Choose this to turn off the LED On Choose this to turn on the LED Blink Choose this to let the LED blink Check this option to let the system automatically refresh the list every 15 seconds Click this button to refresh the list manually Click this button to apply the settings and start to upgrade firmware Click Reset to erase all settings to default values 59
8. AP mode Step 1 To access the WDAP C7200AC open a web browser and enter the default IP address http 192 168 1 253 in the web address field of the browser ea UI E htto 192 168 1 253 C 192 168 1 253 x MN File Edit View Favorites Tools Help Figure 1 1 Login by default IP address After a moment a login window will appear Enter admin for the User Name and Password both in lower case letters Then click the OK button or press the Enter key User Manual of WAPC 1232HP Windows Security The server 192 168 1 253 requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection admin Remember my credentials Figure 1 2 Login Window User Manual of WAPC 1232HP Default IP Address 192 168 1 253 Default User Name admin Default Password admin sf If the above screen does not pop up it may mean that your web browser has been set to a proxy Go to e Tools menu Internet Options Connections LAN Settings on the screen that appears cancel the Using HE Proxy checkbox and click OK to finish it Step 2 Go to the Operation Mode page to set the operation mode to Managed AP Then click Apply Change 3 PL AN ET WDAP C7200AC Natworking amp Communication 802 11ac Ceiling Mount Wireless Access Point Setup Menu Operation Mode gt ion ipei AP Operation mode confi
9. C7200AC v AP Group Member Setting WDAP C7200AC a8 f7 e0 00 14 6a Remove gt gt Figure 4 19 AP Group Management add a new AP group The page includes the following fields Object Description AP Group Setting AP Group Name The AP group name The field length is limited to 16 characters AP Group Description The description of the AP group The field length is limited to 16 characters The model name of the AP AP Model Name Only the same model of the AP can be created as a group to prevent any wireless parameters from inconsistency caused by the provisioning failure AP Group Member Setting Current AP Group Members This section displays the members in this AP group Available Managed APs This section displays the APs conforming to user selected model and is available for grouping Remove gt gt Highlight the current AP and click Remove gt gt to remove it from the group 35 User Manual of WAPC 1232HP Add Highlight the available AP and click Add to add it to the group Apply Click Apply to save and apply the settings Reset Click Reset to erase all settings Wireless AP Group Management Group Description AP Member Setting 2 4GHz Wi Fi Setting 5GHz Wi Fi Setting Add Group Profile Ay Figure 4 20 AP Group Management group list The page includes the following fields Object Description ID This field represents the numerical order of device Enab
10. Enable Auto 100 2346 2347 Disable Enable Enable Enable Enable Disable Disable Enable Enable Enable Figure 4 12 Radio Profile example of 5G radio profile The page includes the following fields 22 User Manual of WAPC 1232HP Object Description Basic Setting Radio Profile Description Channel Network Mode Operation Mode RDG STBC Auto Block Ack Decline BA Request HT Disallow TKIP Channel Bandwidth Guard Interval MCS Enter the name of the profile The operating frequency of the wireless network The default is Auto The network mode of the wireless interface Mixed Mode work in 802 11b g n mode Green Field operates only in 802 11n mode and will not compatible with legacy mode 802 11b g mode Default is Mixed This field only supports in 2 4GHz frequency band When enabling Reverse Direction Grant the wireless AP can reduce the transmitted data packet collision by using the Reverse Direction Protocol During TXOP Transmission Opportunity period the receiver could use the remaining transmission time to transmit data to a sender The RDG improves transmission performance and scalability in a wireless environment Default is Disabled A mechanism that allows a unit with only one antenna to leverage multiple antennas on other 802 11n devices to improve performance and range Default is Disabled An aggregation technique which prevents sending Ack in the commun
11. GROUP MANAGEMENT esse sesse sesse sees esse ee ee eene eene nenne senses eese eese esee esee esee esee ee 34 FIGURE 4 19 AP GROUP MANAGEMENT ADD A NEW AP GROUP ccccccccecceeeeessessseeeeeeecceeeeeeeeaaaeesssseseeeceeeeeeseeeeesssaaassseeeeeeeeeess 35 VII User Manual of WAPC 1232HP FIGURE 4 20 AP GROUP MANAGEMENT GROUP LIST esse esse ee ee ee ese ee ee ee ee ee ee ee ee ee ee ee ee ESEESE ESEESE EEEE E ESEESE ESEESE ESEESE ESEESE EEEn 36 FIGURE 4 21 AP GROUP MANAGEMENT 2 4G WI FI SETTING sesse sees ees ees ee sesse ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee rar EE ee ee ee ee 37 FIGURE 4 22 AP GROUP MANAGEMENT 5G WI FI SETTING ees esse esse esse ee ee ee ee ee ee ee ee see ee ee ee ee ee ee ee ee ee ee ee 39 FIGURE 5 1 MENU AP MONITORING AP STATUS ccccccccccccccscccccecccscsescesessseeseeeesssssesseessseesssssssssssssssssssssssssssssssssssssssssssssseees 4 FIGURE 5 2 AP MONITORING AP STATUS AP STATUS SUMMARY ee esse sesse ee see ee ee ee ee ee ee ee rrr nnn nennen esses sss esse n einn nn ee ee ees 4 FIGURE 5 3 AP MONITORING AP STATUS SSID SUMMARY esse sesse sees sees ee ee ee ee ee ee ee ee ee ee A3 FIGURE 5 4 AP MONITORING AP STATUS RADIO SUMMARY ese esse sesse ese see ee ee ee ee ee ee ee ee senes esses esses esses esee esse sees sess esee esses esee AA FIGURE 5 5 AP MONITORING AP STATUS AP REAL TIME TRAFFIC iese ese esse se see ee ee ee ese
12. Long Preamble can provide better wireless LAN compatibility while the Short Preamble can provide better wireless LAN performance Default is Disabled Long Preamble Calculating the standby time before transmitting data set up the base time for the wireless AP If you enable the Short Slot it can increase performance if you only expect 802 11g traffic 802 11b is not 18 Tx Burst Pkt Aggregate WMM Capable APSD Capable DLS Capable Multicast to Unicast IAPP TX Beamforming Apply Reset User Manual of WAPC 1232HP compatible with short slot time Default is Enabled A performance enhancement that transmits a number of data packets at the same time when the feature is supported by compatible clients Default is Enabled A performance enhancement that combines data packets together when the feature is supported by compatible clients Default is Enabled Provide the basic quality on the wireless network complied with IEEE 802 11 Default is Enabled APSD function is used for controlling power consumption APSD enables the Beacon interval at longer distance until the traffic reaches at the specified point Default is Disabled Direct Link Setting DLS enables all clients data to be transmitted effectively If DSL is enabled the wireless LAN router performs establishing the connection of all the clients at this unit and speeding up of data transmission Default is Disab
13. Short Preamble In IEEE802 11b g mixed environment IEEE802 11g has priority over IEEE802 11b on the connection Auto STA will dynamically change to AP announcement On IEEE802 11g is used first on the connection Off In IEEE802 11b g mixed environment take slower conditions Default is Auto This field only supports in 2 4GHz frequency band The interval of time that this access point broadcasts a beacon Beacon is used to synchronize the wireless network Default is 100 This is the Delivery Traffic Indication Map It is used to alert the clients that multicast and broadcast packets buffered at the AP will be transmitted immediately after the transmission of this beacon frame Default is 1 if not supported it will display 0 You can specify the maximum size of packet during the fragmentation of data to be transmitted If you set this value too low it will result in bad performance Default is 2346 When the packet size is smaller than the RTS threshold the access point will not use the RTS CTS mechanism to send this packet Default is 2347 The Long Preamble can provide better wireless LAN compatibility while the Short Preamble can provide better wireless LAN performance Default is Disabled Long Preamble 24 Short Slot Tx Burst Pkt Aggregate WMM Capable APSD Capable DLS Capable Multicast to Unicast IAPP TX Beamforming Apply Reset User Manual
14. a time 5 37 43 ENSE 00 14 Ga WDAP C7200AC Wi Fi 11ac AP 192 168 1253 1 3465cb150824 oe 0 time 5 49 51 Auto refresh L Figure 5 2 AP Monitoring AP Status AP Status Summary The page includes the following fields Object Description Query by Use one and multiple filtering rules to query the AP and click Refresh to execute the query 41 Status MAC Address Model Device Description Device IP Firmware Version AP Group SSID Profile Radio Profile Auto refresh Refresh User Manual of WAPC 1232HP Status Check this option and filter the AP list by the AP status online or offline AP Model Check this option and filter the AP list by the AP Model that user specifies AP MAC Address Check this option and filter the AP list by the MAC address that user specifies AP IP Address Check this option and filter the AP list by the IP address that user specifies This field represents the numerical order of device Online the AP is online w Offline the AP is offline e Wireless Disable the 2 4G amp 5G wireless signals are both disabled The MAC address of the AP The model name of the AP The device description of the AP This field can be modified through the Setting hyperlink under the sub item General Setting The IP address of the AP The current firmware version of the AP The AP group number of the AP 2 4GHz display the current 2 4G SSID profile that has been appli
15. ee eee cS ven te rae a lesan M 15 FIGURE 4 9 RADIO PROFILE EXAMPLE OF 2 4G RADIO PROFILE esse sees esse ese sees see ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee RR RE ee ee ee ee 16 FIGURE 4 10 2 AG RADIO PROFILE EIS Pie seders ees die Ge ae ER dee kere Be ee Gee ee ees ek Ge kes ee Re Oe Ge ie eek ek Gee dee ee ek De Ge Ge ee 20 FIGURE 4511 5G RADIO PROFILE se ee n ee esse ed ee se ee Gee ed ee Ge Ge Ee aata ge GE ee ee 21 FIGURE 4 12 RADIO PROFILE EXAMPLE OF 5G RADIO PROFILE esse ee ee esse ees ee see ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee i ee RR ee ee ee ee 22 FIGURE 4 13 5G RADIO PROFILE LIST cccceccccccccecceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 26 FIGURE 4 14 AP MANAGEMENT AP LIST sees esse ee ee ee ese ee ee ee ee ee ee ee ee ee ee ee ee EEEE E ESEESE SEESE SESSE SESER ESEESE EESE E EESE Essensen eseese 21 FIGURE 4 15 AP MANAGEMENT GENERAL SETTING cccccccscccccccccececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 20 FIGURE 4 16 AP MANAGEMENT 2 4G WI FI SETTING ccccceeeccccccccceccaeeeessssseseeeeecccceeseesuaeeessssssseseeeeeceseesssssaagegassseeeeeeeeeess 31 FIGURE 4 17 AP MANAGEMENT 5G WI FI SETTING eise sosesss esse de dis uns eek eed uad aka ss seke se e trans ees oe d dul e see eens gee died ses gee us id eramus 33 FIGURE 4 18 AP
16. field displays the data rate of the profile IAPP This field displays the IAPP that is enabled or disabled WMM Capable This field displays the WMM that is enabled or disabled Edit Click Edit hyperlink to re configure the profile Add New 5GHz Radio Click Add New 5GHz Radio Profile button to create a new 5G radio Profile profile Reply In the delete field check the profile that you want to delete and click Apply to apply the setting Reset Click Reset to cancel the check box of the delete option back to 26 User Manual of WAPC 1232HP uncheck status 4 5 AP Management Go to the AP Control gt AP Management page to configure the wireless setting for each managed AP WAPC 1232HP System AP Control AP Search Wireless AP Management Device List SSID Profile Radio Profile AP Management C AP Model AP Group Management C MAC Address AP Group Query by AP Monitoring AP Status REM 10 Stoves ode Device im mac Address Device Description A Group Remove General Sering 2 4GHz WER Setting GHz WER Setting AP Real Time Traffic Active Clients Auto refresh 7 Refresh Rogue AP List uto reires Please click Refresh to query or update the current list Please click Apply to save and apply the setting the setting will take effect after about 60 seconds AP Maintenance DHCP server SNMP Figure 4 14 AP Management AP List The page inc
17. mixed mode c bd d1 57 73 11 WPA2 PSK 7 DrayTek 10F 1 11b g n mixed mode 00 1d aa 29 92 98 WPA PSK 11b g mixed mode 84 c9 b2 09 1d 5e WEP 9 DSL6740C 1 11b g n mixed mode d8 fe e3 5d 01 65 WPA2 PSK 6 jtib g n mixe Oe 18 d6 2f 10 d9 na TIMOTION Guest Figure 5 7 AP Monitoring AP Status Rogue AP List The page includes the following fields Object Description ID This field represents the numerical order of device SSID The SSID name of the rouge AP Channel The channel of the rouge AP Band The frequency band of the rouge AP 49 BSSID Encryption Auto refresh Refresh User Manual of WAPC 1232HP The BSSID of the rouge AP The encryption of the rouge AP Check this option to let the system refresh the AP list every 15 seconds automatically Click Refresh to query or update the current list 50 User Manual of WAPC 1232HP Chapter 6 AP Maintenance In the AP Maintenance section there are five sub menus which make you able to upload the new firmware reboot load factory default and locate the position of single or multiple APs at once OF Maintenance TFTP setting t Firmware Upgrade Group Firmware Upgrade set AF LE Control Figure 6 1 Menu AP Maintenance 6 1 TFTP setting Go to AP Maintenance gt TFTP setting to configure TFTP server for firmware upgrade TFTP Setting X Configured EEN Figure 6 2 AP Maintenance TFTP set
18. of WAPC 1232HP Calculating the standby time before transmitting data set up the base time for the wireless AP If you enable the Short Slot it can increase performance if you only expect 802 11g traffic 802 11b is not compatible with short slot time Default is Enabled A performance enhancement that transmits a number of data packets at the same time when the feature is supported by compatible clients Default is Enabled A performance enhancement that combines data packets together when the feature is supported by compatible clients Default is Enabled Provide the basic quality on the wireless network complied with IEEE 802 11 Default is Enabled APSD function is used for controlling power consumption APSD enables the Beacon interval at longer distance until the traffic reaches at the specified point Default is Disabled Direct Link Setting DLS enables all clients data to be transmitted effectively If DSL is enabled the wireless LAN router performs establishing the connection of all the clients at this unit and speeding up of data transmission Default is Disabled Convert Multicast data to Unicast one Default is Enabled IAPP Inter Access Point Protocol enabled is recommended as it describes an optional extension to IEEE 802 11 that provides wireless access point communications among multivendor systems Default is Disabled Enable TX Beamforming focuses the AP s energy toward a client It increases the
19. performance of wireless networks at medium ranges At short ranges the signal power is high enough that the SNR will support the maximum data rate At long ranges beamforming does not offer a substantial gain over an omnidirectional antenna and data rates will be identical to non beamformed transmissions Default is Enabled oave and apply the settings as a new profile Heset the values to default After creating the 5GHz radio profile you will see the profile in the list Click Apply to save and apply the setting 25 User Manual of WAPC 1232HP WAPC 1232HP e System wv AP Control AP Search Device List SSID Profile Radio Profile 2 46 cr 23 5GHz Wireless Radio Profile Settings AP Management AP Group Management p AP Monitoring AP 143 Ju sable ab Eds m EU Ires Status p AP Maintenance t DHCP server SNMP Figure 4 13 5G Radio Profile List The page includes the following fields Object Description ID This field represents the numerical order of device Delete Check this option and click Apply to delete the profile Radio Profile Description This field displays the description of the profile Network Mode This field displays the network mode of the profile Channel ID This field displays the channel number of the profile Channel Bandwidth This field displays the channel bandwidth of the profile Tx Power This field displays the Tx power of the profile Data Rate This
20. ries ss ee ee ee si enirn nnn nennen ee 54 FIGURE 6 9 AP MAINTENANCE FIRMWARE UPGRADE ccccccccccccccececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 25 FIGURE 6 10 AP MAINTENANCE GROUP FIRMWARE UPGRADE eere ee ee ee ee ee ee ee ee nn rrr nn nn nnne esses ee ee sse n nnn nnn nnne ee ee 56 FIGURE 6511 AP MAINTENANCE RESET AD eee tte ttr pane Hb UE bet nen ie Rea Eb EE Nee ie es EE see ie Eben Be ree ie es ED Ese ie es DE Nee ie GE 57 FIGURE 6 12 AP MAINTENANCE LED CONTROL iss susse ese iese dese ene Ee see dese ese ie Gee de ie ees Ee Ged see Ge ee ie Gee de de ee En Gee dese Gee Ee Ee 58 VIII User Manual of WAPC 1232HP Chapter 1 Configuring the AP and Login the Controller In this manual we use the WDAP C7200AC managed AP as an example to be controlled by the WAPC 1232HP Wireless AP Controller with 8 Port 802 3at PoE Before configuring the WDAP C7200AC in the managed AP mode to be managed by the AP controller please ensure you have upgraded the AP to the firmware that supports the AP controller After the upgrade is finished please go to the Management gt Reload Settings page to upload the latest config file included in the firmware package file After the upload for the configuration is finished please reset the AP to the factory default 1 1 Operation Mode Follow the steps below to set up the operation mode of the WDAP C7200AC in the Managed
21. to 32 characters System Uptime The system bootup time AP LAN Setting 29 DHCP Mode Device IP Device Mask Device Gateway DNS Server NTP Server UPNP Enable Apply Reset 4 5 2 2 4GHz Wi Fi Setting User Manual of WAPC 1232HP This field is used to enable or disable DHCP Server of the AP Static Choose this option to configure the static IP address for the AP DHCP Client Choose this option to obtain the IP address from the DHCP server for the AP DHCP Server Choose this option to assign the IP address to the wireless clients for the AP This field is used to set the IP address of the AP when the DHCP Mode is changed to Static This field is used to set the net mask of the AP when the DHCP Mode is changed to Static This field is used to set the Gateway IP address of the AP when the DHCP Mode is changed to Static This field is used to set the DNS Server of the AP This field is used to set the NTP Server of the AP This field is used to enable or disable UPNP option of the AP Click Apply to save and apply the setting Click Reset to erase all settings to default values Click the Setting hyperlink under the 2 4GHz Wi Fi Setting field to enter the sub menu of AP Management On this page you can designate the AP to use the specific 2 4GHz SSID and Radio profiles 30 User Manual of WAPC 1232HP AP 2 4GHz Wireless Settings ID2 AP Information AP Model WDAP C7200AC AP Ma
22. waste and have to collect such WEEE separately Revision User Manual of PLANET Wireless AP Controller with 8 Port 802 3at PoE Model WAPC 1232HP Rev 1 0 Sep 2015 Part No EM WAPC 1232HP v1 0 2080 E70020 000 CONTENTS Chapter 1 Configuring the AP and Login the Controller monnunennnennnnnannnnnnnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnnaa 1 1 1 OOS eue RE UN 1 Chapter 2 Assigning IP to Managed APS ee liiieeeeeeeee EE EE ERK RR REG ee nns RR RR RR ee sensa asas sanam seas assa RR Re nre nnns 6 Chapter 3 Contiguring the AP Controller i e concours con anc GE US Go GV Pe So ER We eo Ee Ge EG We ee 8 Chapter 4 AP Control issie iss eine ee ve ee ie boe ed a aaa su RE ee die one ee Dee we kinda Gee oe ed WE i 9 EN Sie EE i 9 ru Ec AE EE EE EE EE NE 10 ko EN MEE EE DE EE EE EE EE N EL EE ror eeeee 12 44 Radi uie EE N EE N N ON 15 LP MEME Cree lU TE m T 15 442 5G Radio iei AA N N EE mmm vmt amm vol 21 45 AP MiNagenme eee 27 ASA Genera Se IAG MER 28 4 5 2 2 4GHz Wi c ugem 30 4 5 3 5GHz Wi Fi UNO EE ie Ga EG A MAS MAA AMET UU 32 46 AP Group Manageo on iei sie Es EER EE ee Ee ee EG OR ee en ee Ge ek Ee 34 4 6 1 2 4GHz Wi Fi Setting tenente trennen reete tr ee ee rnr arrra 37 QO MEE 619 7484 depo sessie n Ee Ee Ge ee ee Ee ee ae oa SO EG Ee IE 38 Chapter 5 AP Moriitoring
23. 0 14 6a WDAP C 7200 AC Wi Fi 11ac AP 1256 8299 Auto refresh L1 Figure 5 5 AP Monitoring AP Status AP Real Time Traffic The page includes the following fields Object Description AP Wireless Traffic Statistics Use one and multiple filtering rules to query the AP and click Refresh to execute the query AP Model Check this option and filter the AP list by the AP Model that user Query by specifies AP MAC Address Check this option and filter the AP list by the MAC address that user specifies Frequency Band Check this option and filter the AP list by the frequency 46 ID AP MAC Address AP Model Device Description Frequency Band SSID Sent Packets Received Packets AP LAN Traffic Statistics User Manual of WAPC 1232HP band that user specifies SSID Check this option and filter the AP list by the SSID name that user specifies This field represents the numerical order of device The MAC address of the wireless interface The model name of the AP The device description of the AP This field can be modified through the Setting hyperlink under the sub item General Setting The frequency band of the AP The SSID name of the AP The packets sent by this interface The packets received by this interface ID AP MAC Address AP Model Device Description Sent Packets Received Packets Auto refresh Refresh This field represents the numerical order of device The MAC a
24. AP Status ius sessies dei si oek es de ee RE ee ee ie eg oe bu ei oe ed de ka 41 S1 AP SAWS SUINIG Vossie 41 52 5510 SUMMAD EE E AA Ee 43 5 9 Radio kolli niin ln AA uuu EE EO EN Ed 44 S4 AFRE TME TATE a 46 99 side OM EE EE TD AE aaa aaa 47 4 MN ROC EE EE OE PP 49 Chapter 5 AP Maintelialie e cece aaa o vd ee aiad jala Ee ee Ee ai im 51 User Manual of WAPC 1232HP 6 1 6 2 6 3 6 4 6 5 User Manual of WAPC 1232HP Bid ue E EE EE 51 FNWI dese io c 54 Group Firmware Upgrade m 56 il e 57 EED CONT M Maa EDEN 58 VI User Manual of WAPC 1232HP FIGURES FIGURE 1 1 LOGIN BY DEFAULT IP ADDRESS 4 see n aput Ens ina De oe ee ee Ge be Ma oe se oe oe ee Um Re Es deu isa EE Ge ed oe ateism 1 FICURE L A LOGIN WINDOW III AIA OO EE i ED EE 2 FIGURE 1 3 OPERATION MODE MANAGED AP 1166666vevenenennnnn enn ee ee ee ee ee ee ee ee AAR RR EE Ee ee ee ee ee ee ee ee ee AA anne nnn ener eese s nsns nns 3 FIGURE 1 4 TOPOLOGY CONNECT TO AP CONTROLLER sesse ee ee ee esse ee ee ee ee ee ee ee ee ee ee ee ee ee ee RR RR EE Ee ee ee ee ee ee ee ee ee AA RR EE ee ee ee ee ee ee ee ee A FIGURE 1 5 LOGIN TO THE AP CONTROLLER se ee se ee t na ika aada ee ee ea P
25. Address The MAC address of the AP Device Description The device description of the AP No Action Choosing this will not do any action to the AP Reset Factory default Choose this to reset the AP to factory default Reboot only Choose this to reboot the AP Auto Refresh Check this option to let the system automatically refresh the list every 15 seconds Refresh Click this button to refresh the list manually Apply Click this button to apply the settings and start to upgrade firmware Reset Click Reset to erase all settings to default values 6 5 LED Control Go to AP Maintenance gt LED Control to turn on off the LED or locate the position of the AP In the Position LED field select the action from the drop down list and click Apply to start the procedure Led control Power LED ON Position LED ON Position LED Blink Emm ca Device IP MAC Address Device Description Position LED T 132 168 1 151 a8 f e0 00 00 01 Wi Fi Mac AP E WDAP C7200AC 192 168 1 152 a8 1 80 00 14 ba Wi Fi 11ac AP Auto refresh LJ Please click Refresh to query or update the current list Please click Apply to save and apply the setting the setting will take effect after about 60 seconds Figure 6 12 AP Maintenance LED Control 58 User Manual of WAPC 1232HP The page includes the following fields Object ID Model Device IP MAC Address Device Description Position LED Auto Refresh
26. Chapter 4 AP Control In the AP Control section there are six sub menus which make you able to discover AP create profile and upload the pre defined profiles to single or multiple APs at once AP Control AP Search t Device List SSID Profile Radio Profile gt Ele FP DU OP Management AF Group Management Figure 4 1 Menu AP Control 4 1 AP Search Go to the AP Control gt AP Search page and then click Refresh to discover the managed AP available in the network Only the AP existed in the same network segment can be discovered and added to the device list of controller A maximum of 64 devices can be found on the AP Search page Q PLANET WAPC 1232HP System AP Control AP Searcn Device List SSID Profile Radio Profile e AP Management AP Group Management A pi X P Smart Discovery AP Monitoring AP Status AP Maintenance A gt 5 2 E d DHCP ID MAC Address AP Model Version Device IP Device Netmask Device Gateway Device Description Select Device gt server SNMP Port Management Link Aggregation Auto Refresh O Figure 4 2 AP Search User Manual of WAPC 1232HP In the Select Device field check the AP that you want to manage and then click Apply System AP Control AP Search Device List SSID Profile Radio Profile AP Management AP Group Management AP Monitoring AP Status WAPC 1232
27. Click this button to apply the settings and start to upgrade firmware 55 User Manual of WAPC 1232HP Reset Click Reset to erase all settings to default values For the example of firmware upgrade please refer to the Example of TFTP Setting and Firmware Upgrade 6 3 Group Firmware Upgrade Go to AP Maintenance Group Firmware Upgrade to configure the firmware upgrade for the AP group Select the group from the drop down list and click Apply to start firmware upgrade procedure for the selected group AP upgrade firmware Gop v 1 WDAP W7200AC 192 168 1 151 a8 f7 20 00 00 01 Wi Fi 11ac AP 1 3465cb150825 Auto refresh LI Refresh Figure 6 10 AP Maintenance Group Firmware Upgrade The page includes the following fields Object Description ID This field represents the numerical order of device Model The model name of the AP The IP address of the AP Device IP On the Device List page the IP address is a hyperlink which enables the user to link to the AP s Web configuration page directly MAC Address The MAC address of the AP Device Description The device description of the AP Firmware Version The current firmware version of the AP Percentage This field displays the percentage of upgrade progress This field indicates the progress of upgrade procedure Progress This icon indicates the upgrade is in progress eo This icon indicates the upgrade is successful 56 User Manual o
28. HP Smart Discovery 4 M 7 ID MAC Address AP Model Device Netmask Device Gateway Device Description Select Device b f SNMP 1 a8 47 20 00 14 6a WDAP C7200AC 1 3465cb150806 192 168 1 253 255 255 2550 192 168 1 254 Wi Fi 11ac AP iv y Port Management Link Aggregation VLANs Auto Refresh I Apply Figure 4 3 AP Search select the AP from the list The page includes the following fields Object ID MAC Address AP Model Version Device IP Device Netmask Device Gateway Device Description Select Device Auto Refresh Refresh Apply 4 2 Device List Description This field represents the numerical order of device The MAC address of the AP The model name of the AP The current firmware version of the AP The IP address of the AP The netmask of the AP The gateway IP address of the AP The device description of the AP Check this option to select the device from the managed AP list Check this option to let the system automatically refresh the list every 15 seconds Click this button to refresh the list manually Click this button to apply the settings Go to the AP Control gt Device List page to ensure the AP is already selected from the list This section is to confirm the AP selected on the AP Search page has been added to the Device List Table so that we can control it 10 User Manual of WAPC 1232HP by the following sections On this page you can click the h
29. Hz Radio Profile to the AP s 2 4GHz Radio Profile advanced setting To create new 2 4GHz radio profile please go to the Radio Profile gt 2 4G page Apply Click Apply to save and apply the setting Reset Click Reset to erase all settings to default values 4 5 3 5GHz Wi Fi Setting Click the Setting hyperlink under the 5GHz Wi Fi Setting field to enter the sub menu of AP Management On this page you can designate the AP to use the specific 5GHz SSID and Radio profiles 30 User Manual of WAPC 1232HP AP 5GHz Wireless Settings ID2 AP Information WDAP C7200AC 38 7 e0 00 14 6a AP description Wi Fi 11ac AP AP IP Address 192 168 1 253 5GHz SSID Configuration E SSID 1 55572 2 ELTER S5ID3 Dee v mor 4 Disable v aa Figure 4 17 AP Management 5G Wi Fi Setting The page includes the following fields Object Description AP Information AP Model The model name of the AP AP MAC The MAC address of the AP AP Description The device description of the AP To edit this field please go to the General Setting page AP IP Address This IP address of the AP 33 User Manual of WAPC 1232HP 5GHz SSID Configuration This field is used to designate the 5GHz SSID Profile to the AP s 5GHz ju SSID 1 To create new SSID profile please go to the SSID Profile page SSID 2 This field is used to designate the 5GHz SSID Profile to the AP s 5GHz SSID 2 To create new SSID profi
30. User Manual of WAPC 1232HP AP upgrade firmware Device Description Firmware Version Percentage Upgrade Firmware 1 WDAP W7200AC 192 168 1 151 a8 f7 20 00 00 01 Wi Fi 11ac AP 1 3465cb1508225 o d 2 WDAP C7200AC 192 168 1 152 a8 f7 20 00 14 6a Wi Fi 11ac AP 1 3465cb1508224 x 0 oOo Auto refresh L Apply Figure 6 9 AP Maintenance Firmware Upgrade The page includes the following fields Object Description ID This field represents the numerical order of device Model The model name of the AP The IP address of the AP Device IP On the Device List page the IP address is a hyperlink which enables the user to link to the AP s Web configuration page directly MAC Address The MAC address of the AP Device Description The device description of the AP Firmware Version The current firmware version of the AP Percentage This field displays the percentage of upgrade progress This field indicates the progress of upgrade procedure This icon indicates the upgrade is in progress Progress This icon indicates the upgrade is successful 3 This icon indicates the upgrade failed Status This field indicates the status of upgrade procedure Upgrade Firmware Check this option to select the device for firmware upgrade Auto Refresh Check this option to let the system automatically refresh the list every 15 seconds Refresh Click this button to refresh the list manually Apply
31. allowed at all times to ensure the safe use of the equipment National Restrictions This device is intended for home and office use in all EU countries and other countries following the EU directive 1999 5 EC without any limitation except for the countries mentioned below Country Bulgaria France Italy Luxembourg Norway Russian Federation Restriction None Outdoor use limited to 10 mW e i r p within the band 2454 2483 5 MHz None None Implemented None Reasons remarks General authorization required for outdoor use and public service Military Radiolocation use Refarming of the 2 4 GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012 If used outside of own premises general authorization is required General authorization required for network and service supply not for spectrum This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny Alesund Only for indoor applications Note Please don t use the product outdoors in France User Manual of WAPC 1232HP WEEE regulation To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal
32. c a8 f7 80 00 14 6a AP description AP IP Address 192 168 1 253 2 4GHz SSID Configuration 2 4G SSID 1 v Disable Disable 2 4GHz Radio Configuration 2 4GHz Radio Profile List rafile Figure 4 16 AP Management 2 4G Wi Fi Setting The page includes the following fields Object Description AP Information AP Model The model name of the AP AP MAC The MAC address of the AP AP Description The device description of the AP To edit this field please go to the General Setting page AP IP Address This IP address of the AP 31 User Manual of WAPC 1232HP 2 4GHz SSID Configuration This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz ae SSID 1 To create new SSID profile please go to the SSID Profile page SSID 2 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 2 To create new SSID profile please go to the SSID Profile page SSID 3 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 3 To create new SSID profile please go to the SSID Profile page SSID 4 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 4 To create new SSID profile please go to the SSID Profile page SSID 5 This field is used to designate the 2 4GHz SSID Profile to the AP s 2 4GHz SSID 5 To create new SSID profile please go to the SSID Profile page 2 4GHz Radio Configuration This field is used to designate the 2 4G
33. check status 4 4 Radio Profile In this section you can create wireless advanced settings as 2 4GHz profile or 5GHz profile for future provisioning to multiple APs 4 4 1 2 4G Radio Profile Go to the AP Control gt Radio Profile gt 2 4G page to create a new 2 4GHz wireless profile related to wireless advance parameters WAPC 1232HP System AP Control 2 4GHz Wireless Radio Profile Settings AP Search Device List SSID Profile Radio Profile j 1 Ae AP Management AP Group Management zo Batete Radio Profle Description Network Mode channel 1D Channel Bandwidth Tx Power Date rate TAPP wrm Capable Edi AP Monitorin AP Sic 9 Add New 2 4GHz Radio Profile AP Maintenance DHCP server Figure 4 8 2 4G Radio Profile 15 Example of the 2 4G Radio Profile Device List SSID Profile Radio Profile 2 46 5G gt AP Management AP Group Management AP Monitoring AP status AP Maintenance r DHCP server SNMP Port Management Link Aggregation VLANS spanning Tree User Manual of WAPC 1232HP WAPC 1232HP Add Radio Profile Basic Setting Radio Profile Description Hetwork Mode RDG STBC Auto Block Ack Decline BA Request MCS 2 4GHz Radio Profile 2412MHZ Channel 1 11b g n mixed mode RDG Disable v Disable Disable Disable 2 4GHz Radio Profile Auta 11b g n mixed mode mixed mode Disable Disable Disabl
34. ddress of the LAN interface The model name of the AP The device description of the AP This field can be modified through the Setting hyperlink under the sub item General Setting The packets sent by this interface The packets received by this interface Check this option to let the system refresh the AP list every 15 seconds automatically Click Refresh to query or update the current list 5 5 Active Clients Go to AP Monitoring AP Status gt Active Clients to check current associated clients of the managed APs 47 User Manual of WAPC 1232HP Active Clients Query by CI AP Model SS O Client MAC Address L SSID NENNEN C AP MAC Address NENNEN MAC AP AP MAC Tx Tx Time N TT me WDAP Planet AP 11a ac n mixed Auto refresh 0 Refresh Figure 5 6 AP Monitoring AP Status Active Clients The page includes the following fields Object Description Use one and multiple filtering rules to query the AP and click Refresh to execute the query AP Model Check this option and filter the AP list by the AP model that user specifies Client MAC Address Check this option and filter the list by the Client MAC Query by address that user specifies SSID Check this option and filter the list by the SSID name that user specifies AP MAC Address Check this option and filter the list by the AP MAC address that user specifies ID This field represents the numerical order of device
35. default settings once it is reverted to the Standalone AP mode The page includes the following fields Object Description User Manual of WAPC 1232HP In the Standalone AP mode the AP acts as an individual AP in the Standalone AP network and you manage it by using the Administrator Web User Interface Ul or SNMP In the Managed AP mode the AP is part of the PLANET Wireless AP Managed AP controller System and you manage it by using the WAPC Wireless Switch IP address of the AP Controller Default 0 0 0 0 The default IP address of the PLANET AP Controller is 192 168 1 100 AP Controller IP Address Entering 0 0 0 0 means all AP controllers in the same network segment are able to manage this AP Managed AP WAPC Wireless AP Controller with PoE Laptop Figure 1 4 Topology connect to AP Controller http 192 168 1 100 gt Q 5192 168 1 100 Figure 1 5 Login to the AP Controller User Manual of WAPC 1232HP PLANET WAPC 1232HP M x Y gt Q D 192 168 1 100 PLANE Netweorkisg amp Comemaeication WAPC 1232HP Welcome to PLANET gt 3 rt Mana Ent WAPC 1 2 3 2 H P egation Wireless AP Controller with 8 port 802 3at PoE PLANET Technology Corporation 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528 Email Support amp planet com tw Copyright 2015 PLANET Technology Corpora
36. e Disable Disable 40 Long Auto Advanced Setting T cenigured Current BG Protection Mode Auto Beacon Interval 20 1024 ms 100 Multicast t OOS Access Control List Authentication Security MAC Address Table LLDP Diagnostics POE Loop Protection RMON 100 Data Beacon Rate OTIM 1255 1 2346 2347 Disable Enable Enable Enable Enable Disable Disable Enable Enable Enable Enable Y WMM Capable Disable gt Enable iv IAPP Enable Enable Figure 4 9 Radio Profile example of 2 4G radio profile Logout el The page includes the following fields 16 User Manual of WAPC 1232HP Object Description Basic Setting Radio Profile Description Enter the name of the profile Channel The operating frequency of the wireless network The default is Auto Network Mode The network mode of the wireless interface Mixed Mode work in 802 11b g n mode Green Field operates only in Operation Mode 802 11n mode and is not compatible with legacy mode 802 11b g mode Default is Mixed When enabling Reverse Direction Grant the wireless AP can reduce the transmitted data packet collision by using the Reverse Direction Protocol During TXOP Transmission Opportunity period the receiver could use im the remaining transmission time to transmit data to a sender The RDG improves transmission performance and scalability in a wireless en
37. e DP atcp SE ee ee MORET Pe RO ED a isata De A FIGURE 1 6 AP CONTROLLER MAIN ccccccccccccccceececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess 5 FIGURE 2 1 DHCP SERVER MODE ees esse sees esse esse ee ee ee ee eene nennen nnne eene eene esee eese e eese e eese e esee esee esee esee esee esee esee eese esee esee eee eese eese eese eee 6 FIGURE 2 2 SYSTEM SAVE STARTUP CONFIG ccccccccccccccccececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess 6 FIGURE 2 3 DHCP SERVER BINDING ede sees ee ee see ee ee ee ee ee ee ee ee ee ee ee ee ee ESEESE EEEE E ESEESE SEESE SESSE EEEE S SESSE SEESE SESSE SEESE ESEESE REEERE 7 FICURE P E AG aur ce EE SE En AE EE a AAA 2 8 EIGURE 4 8 MENG AE CONT OT roles en ee ee Ee ee Gegee Ee Ee ee ee EE ee ee EE ee EE 9 EIGURE ile AE N EE 9 FIGURE 4 3 AP SEARCH SELECT THE AP PROM THE LIST rooster gek ee ese ee Ge es se ee ee bee ee ds ee see eie se dee ee ee gee ee see se ei 10 BIGURE dd DEVICES T ooi ee 0 11 PIGURE 45 SI EROEIEE Mc 12 FIGURE 4 6 SSID PROFILE EXAMPLE soicsseccaneccsivcecscncdamesaccnaaiahsunsitobewenssdennsscebevasesabsensianbavenssnddnniscebedasedebsensitebadentandenndscebedesetalees 12 PIGURE 4 7 SSID PRORCE lt S ICT 14 FIGURE 4 5 24G RADIO PROFI EE ot sce cote ee ee ee ac OE ie ee Ee GE EA
38. e Statement This equipment has been tested and found to comply with the limits for a Class B digital device FC pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution To assure continued compliance use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two condition
39. e modified through the Setting hyperlink under the sub item General Setting The frequency band of the AP The radio profile description of the AP The network mode of the AP The channel number of the AP The channel bandwidth of the AP The Tx Power of the AP The data rate of the AP The current IAPP status of the AP The current WMM status of the AP Check this option to let the system refresh the AP list every 15 seconds automatically Click Refresh to query or update the current list 45 User Manual of WAPC 1232HP Apply Click Apply to save and apply the setting Reset Click Reset to erase all settings to default values 5 4 AP Real Time Traffic Go to AP Monitoring AP Status gt AP Real Time Traffic to check real time traffic of the managed APs including the LAN and wireless physical interfaces AP Real Time Traffic Query by iu Model AP MAC Address AS ss MAC Address C Frequency Band Fregue Varo ea Osio TE SSID AP Wireless Traffic Statistics Es AP MAC Address AP Model Device Description i ita band SSID Send Packets Received Packets 1 a8 f7 20 00 00 03 WDAP WT200AC Wi Fi Tlac AP a8 7 e0 00 00 02 WDAP W7200AC Wi Fi 11ac AP 6 TF anet AP 5 a8 7 e0 00 14 6c WDAP C7200AC Wi Fi 11ac AP a8 7 e0 00 14 66 WDAP C7200AC Wi Fi 11ac AP SS SS RE SE E AP LAN Traffic Statistics DEE EI MIT Deine 1 a8 f7 e0 00 00 01 WDAP W7200AC Wi Fi 11ac AP 2444 2421 a f7 e0 0
40. e the 5GHz SSID Profile to the AP s 5GHz SSID 4 To create new SSID profile please go to the SSID Profile page SSID 5 This field is used to designate the 5GHz SSID Profile to the AP s 5GHz SSID 5 To create new SSID profile please go to the SSID Profile page 5GHz Radio Configuration This field is used to designate the 5GHz Radio Profile to the AP s 5GHz Radio Profile advanced setting To create new 5GHz radio profile please go to the Radio Profile gt 5G page Apply Click Apply to save and apply the setting Reset Click Reset to erase all settings to default values 40 User Manual of WAPC 1232HP Chapter 5 AP Monitoring AP Status In the AP Monitoring section there are six sub menus which make you able to observe the current status of single or multiple APs at once AP Monitoring AP status AP Status Summary SSID Summary x Radio Summary AP Real Time Traffic Active Clients w Fi acie AP List r 2 45 eEG Figure 5 1 Menu AP Monitoring AP Status 5 1 AP Status Summary Go to AP Monitoring AP Status gt AP Status Summary to check the status of the managed APs in the Device List AP Status Summary Query by O Staus O Ee a JAP Model X S ER Model O AP MAC Address AP MAC Address ELE EE ID Status MAC Address Mode Device Description Device IP Firmware Version AP Group a Up Time d is 00 00 01WDAP WT7200AC Wi Fi Mac AP 1192 168 1252 1 3465cb150825 2
41. ed to this AP 5GHz display the current 5G SSID profile that has been applied to this AP x If no profile has been applied to the AP it will not display any value 2 4GHz display the current 2 4G Radio profile that has been applied to this AP 5GHz display the current 5G Radio profile that has been applied to this AP lt If no profile has been applied to the AP it will not display any value Check this option to let the system refresh the AP list every 15 seconds automatically Click Refresh to query or update the current list 42 User Manual of WAPC 1232HP 5 2 SSID Summary Go to AP Monitoring AP Status SSID Summary to check each SSID configuration status of the managed APs in the Device List SSID Summary Query by EE E AP Model HA MAE Hem AP MAC Address Osso Band Band 11b aa AP ek Device ale bi Associated SSID a f7 e0 00 00 ilt s ps TE n mixed EN AP ao t el 00 00 5 a6 f7 e0 00 00 WDAP Ta Ap 11a ac n mixed Planet AP r ao t eU UL LI Enable 01 WT200AC ide e 02 En a es 00 14 I xs T n mixed ao f7 e0 00 14 a fr 00 14 Mert E 11a ac n mixed aa f e0 00 14 E Auto refresh LJ Figure 5 3 AP Monitoring AP Status SSID Summary The page includes the following fields Object Description Use one and multiple filtering rules to query the AP and click Refresh to execute the query AP Model Check this option and filter the AP list by the AP model that
42. ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee RE ee ee ee A6 FIGURE 5 6 AP MONITORING AP STATUS ACTIVE CLIENTS cccccccscccccccececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess 48 FIGURE 5 7 AP MONITORING AP STATUS ROGUE AP LIST sees sees sees ees se ese ee ee ee ee de ee ee ee ede ee ee eese es de ee ee ee een A9 FIGURE 6 1 MENU AP MAINTENANCE esse esse see see ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee esee sees esses ess ses see es sees eis 31 FIGURE 6 2 AP MAINTENANCE TFTP SETTING ees sesse esse ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee E SESER SESSE SEESE EEEE EEEE n neeesa nsss eseese ssena 51 FIGURE 6 3 TFTP SERVER SETTING COPY FIRMWARE TO THE SERVER cessere nnn ee ee ee ee ee nsns ee ee ee n rrr ee ee ee nnns 52 FIGURE 6 4 TFTP SERVER SETTING SET DIRECTORY AND IP ees sesse esse sesse sees ese see ee ee ee ee ee ee ee ee ee ee ees ee ee ee ee ee dd eek ee ee GE EE ES 53 FIGURE 6 5 TFTP SERVER SETTING LOCATE FIRMWARE AND CONFIGURE TFTP SERVER IP ees sesse ee ee ee ee ee ee ee ee ee ee ee ee ee ee 53 FIGURE 6 6 TE EP SERVER SE FEING SEINISH oes iets eeste de ene sl ee ede ees ee ese de eek ae ee vee kami ese de ee de ee ede er GE ee 54 FIGURE 6 7 FIRMWARE UPGRADE SELECT THE AP 54 FIGURE 6 8 FIRMWARE UPGRADE START TO UPGRADE eeue ees sesse ee ee ee ee ee ees ee ee ee ee see ee ee ee ee ee ee ee i enin nnn nnne
43. f WAPC 1232HP eo This icon indicates the upgrade failed Status This field indicates the status of upgrade procedure Auto Refresh Check this option to let the system automatically refresh the list every 15 seconds Refresh Click this button to refresh the list manually Apply Click this button to apply the settings and start to upgrade firmware Reset Click Reset to erase all settings to default values 6 4 Reset AP Go to AP Maintenance gt Reset AP to reboot or reset the AP to factory default In the Reset field select the action from the drop down list and click Apply to start the procedure Reset AP ID Model Device IP MAC Address Device Description 1 WDAP W7200AC 192 168 1 151 a8 f7 e0 00 00 01 Wi Fi 11ac AP WDAP C7200AC 192 168 1 152 38 f7 80 00 14 6a Wi Fi 11ac AP No Action factory default reboot onl Auto refresh L Please click Refresh to query or update the current list Please click Apply to save and apply the setting the setting will take effect after about 60 seconds Figure 6 11 AP Maintenance Reset AP The page includes the following fields Object Description ID This field represents the numerical order of device Model The model name of the AP The IP address of the AP Device IP On the Device List page the IP address is a hyperlink which enables the user to link to the AP s Web configuration page directly 57 User Manual of WAPC 1232HP MAC
44. g locate firmware and configure TFTP server IP TF TP Setting Configured Current C7200AC 1 3465cb150825 bin werlb 192 168 1 8 User Manual of WAPC 1232HP Figure 6 6 TFTP Server Setting finish AP upgrade firmware D ede Device ip mac Address Device Description Firmware version Percentage Progress Status Upgrade Firmware 1 WDAP W7200AC 192 168 1 151 a8 7 20 00 00 01 Wi Fi 11ac AP 1 3465cb150825 o D WDAP C7200AC 192 168 1 152 a8 f7 e0 00 14 6a Wi Fi 11ac AP 13465cb1508224 x 0 HM Auto refresh L Figure 6 7 Firmware Upgrade select the AP AP upgrade firmware io modei Device 1P WAC Address Device Description Firmware Version Percentage Progress Status upgrade Firmware 1 WDAP W7200AC 192 168 1 151 38 57 e0 00 00 01 Wi Fi ac AP 1 3465cb150825 om EH WDAP C7200AC 192 168 1 152 a8 f7 20 00 14 6a Wi Fi 11ac AP 1 3465cb150824 46 BEBE Reboting iO Auto refresh The uploaded firmware image is being transferred to flash The system will restart after the update Until then do not reset or power off the AP Figure 6 8 Firmware Upgrade start to upgrade 6 2 Firmware Upgrade Go to AP Maintenance gt Firmware Upgrade to configure the firmware upgrade of the managed AP in the list Check the Upgrade Firmware option to select the AP to upgrade the new firmware and then click Apply to start firmware upgrade procedure 54
45. guration is used to configure the managed AP administrative mode Standalone AP gt Setup Wizard In Standalone AP the AP acts as an individual AP in the gt WLAN1 5 GHz network and you manage it by A TOW e E using the Administrator Web gt WLAN 2 4 GHz Standalone AP In Mode Standalone AP the AP acts as an individual AP in the User Interface UI or SNMP v TCP IP Settings User Interface UT or SNMP Managed AP In Managed AP the AP is part network and you manage it by using the Administrator Web LAN Interface of the PLANET Wireless AP controller System and you gt Management In Mode Managed AP the AP is part of the PLANET Wireless OU Ey ame ME ARE AP controller System and you manage it by using the WAPC Wireless Switch Log out Wireless Switch gt Reboot AP Controller IP Address 0 0 0 0 After vou configure the settings on the AP Operation Mode page you must click Apply button to apply the changes and to save the settings Changing some settings might cause the AP to stop and restart system processes If this happens wireless chents will temporarily lose connectivity We recommend that you change AP settings when WLAN traffic is low Figure 1 3 Operation Mode Managed AP Z Please back up the configuration settings before switching from the Standalone AP mode to the Managed P e AP mode All the configurations will be erased and at the same time the system will return to the factory Mir
46. ication to reduce the network congestion If this option is enabled the device will try to activate this function when transmitting massive data Default is Disabled Enable this option to decline the Block Ack request addressed by the other devices Default is Disabled Prevents the use of TKIP data encryption when using 802 11n high throughput data rates Default is Disabled The channel bandwidth of the 5GHz wireless interface Default is 80 Guard intervals are used to ensure that distinct transmissions do not interfere with one another Only effective under Mixed Mode Default is Long The Modulation and Coding Scheme MCS is a value that determines 23 HT Tx Stream HT Rx Stream Tx Power Advanced Setting User Manual of WAPC 1232HP the modulation coding and number of spatial channels Default is Auto HT means High Throughput The number of HT TxStream means how many antennas will transmit data simultaneously Option 1 or 2 Default is 2 The number of HT RxStream means how many antennas will receive data simultaneously Option 1 or 2 Default is 2 You can adjust the wireless transmit power here By reducing the TX power you can reduce the wireless coverage to make it only cover the area you need Default is 100 BG Protection Mode Beacon Interval 20 1024 ms Data Beacon Rate DTIM 1 255 Fragment Threshold 256 2346 RTS Threshold 0 2347
47. le please go to the SSID Profile page SSID 3 This field is used to designate the 5GHz SSID Profile to the AP s 5GHz SSID 3 To create new SSID profile please go to the SSID Profile page SSID 4 This field is used to designate the 5GHz SSID Profile to the AP s 5GHz SSID 4 To create new SSID profile please go to the SSID Profile page SSID 5 This field is used to designate the 5GHz SSID Profile to the AP s 5GHz SSID 5 To create new SSID profile please go to the SSID Profile page 5GHz Radio Configuration This field is used to designate the 5GHz Radio Profile to the AP s 5GHz Radio Profile advanced setting To create new 5GHz radio profile please go to the Radio Profile gt 5G page Apply Click Apply to save and apply the setting Reset Click Reset to erase all settings to default values 4 6 AP Group Management Go to the AP Control gt AP Group Management page to create a new AP group and then configure the wireless setting by group Click Add Group Profile to add the new AP group WAPC 1232HP system AP Control AP Search ID Enable Group Name Group Description AP Member Setting 2 4GHz Wi Fi Setting 5GHz Wi Fi Setting Wireless AP Group Management Device List SSID Profile Radio Profile AP Management AP Group Management Figure 4 18 AP Group Management 34 User Manual of WAPC 1232HP AP Group Setting AP Group Name AP Group Description EE AP ModelName WDAP
48. le Check the group that you want to upload the new setting and click Apply to take effect Group Name This field displays the group name Group Description This field displays the group description Delete Check the group that you want to delete and click Apply to delete the group AP Member Setting Click Edit to edit the group 2 4GHz Wi Fi Setting Click the Setting hyperlink to apply the 2 4GHz SSID and Radio profiles to the AP group 5GHz Wi Fi Setting Click the Setting hyperlink to apply the 5GHz SSID and Radio profiles to the AP group Click the Apply button to let the following behaviors take effect Apply 1 In the Enable field check the group that you want to upload the new setting and click Apply to take effect 2 In the Delete field check the group that you want to delete and click 36 User Manual of WAPC 1232HP Apply to delete the group Reset Click Reset to cancel any check box back to uncheck status 4 6 1 2 4GHz Wi Fi Setting Click the Setting hyperlink under the 2 4GHz Wi Fi Setting field to enter the sub menu of AP Group Management On this page you can designate the AP group to use the specific 2 4GHz SSID and Radio profiles AP 2 4GHz Wireless ID1Settings AP Group Information AP Group Name AP Group Description 2 200AC Group 2 4GHz SSID Configuration SSID No SSID Profile 246 SSID 1 v SSID SSID 3 SSID 4 SSID 5 2 4GHz Radio Configuration
49. led Convert Multicast data to Unicast one Default is Enabled IAPP Inter Access Point Protocol enabled is recommended as it describes an optional extension to IEEE 802 11 that provides wireless access point communications among multi vendor systems Default is Disabled Enabling TX Beamforming focuses the AP s energy toward a client It increases the performance of wireless networks at medium ranges At short ranges the signal power is high enough that the SNR will support the maximum data rate At long ranges beamforming does not offer a substantial gain over an omnidirectional antenna and data rates will be identical to non beamformed transmissions Default is Enabled Save and apply the settings as a new profile Heset the values to default After creating the 2 4GHz radio profile you will see the profile in the list Click Apply to save and apply the setting 19 User Manual of WAPC 1232HP WAPC 1232HP System 2 4GHz Wireless Radio Profile Settings AP Control AP Search Device List SSID Profile Rada Profile amp 2 46 i SG AP Managerment amp AP Group Management AP Monitoring J AF Status r AP Maintenance DHCP server Te SNMP eer Reset n Add hew 2 sr Rade Profile Figure 4 10 2 4G Radio Profile List The page includes the following fields Object Description ID This field represents the numerical o
50. ludes the following fields Object Description Use one and multiple filtering rules to query the AP and click Refresh to execute the query Status Check this option and filter the AP list by the AP status online or offline Query by AP Model Check this option and filter the AP list by the AP Model that user specifies MAC Address Check this option and filter the AP list by the MAC address that user specifies AP Group check this option and filter the AP list by the group that user specifies ID This field represents the numerical order of device Online the AP is online Offline the AP is offline Wireless Disable the 2 4G amp 5G wireless signals are both disabled Status 27 Model Device IP MAC Address Device Description AP Group Remove General Setting 2 4GHz Wi Fi Setting 5GHz Wi Fi Setting Auto refresh Refresh Apply Reset User Manual of WAPC 1232HP The model name of the AP The IP address of the AP The MAC address of the AP The device description of the AP This field can be modified through the Setting hyperlink under the sub item General Setting If the AP has been added to a group the General Setting 2 4GHz Wi Fi Setting and 5GHz Wi Fi Setting will be disabled user must go to the AP Group Management page to configure this through its group Check this option and click Apply to remove the AP from the list Click the Setting hyperlink
51. on mode Number Bandwidth Power Rate Capable Al a6 f7 e0 00 WDAP T 11b g n mixed a8 f7 e0 00 WDAP ET 11a ac n a8 f7 e0 00 WDAP si 11b g n mixed a8 f7 e0 00 WDAP C 11a ac n Auto refresh LI Apply Please click Refresh to query or update the current list Please click Apply to save and apply the setting the setting will take effect after about 60 seconds Figure 5 4 AP Monitoring AP Status Radio Summary The page includes the following fields 44 Object User Manual of WAPC 1232HP Description Query by ID AP MAC Address AP Model Device Description Frequency Band Radio Profile Description Network Mode Channel Number Channel Bandwidth Tx Power Data Rate IAPP WMM Capable Auto refresh Refresh Use one and multiple filtering rules to query the AP and click Refresh to execute the query AP Model Check this option and filter the AP list by the AP model that user specifies AP MAC Address Check this option and filter the AP list by the MAC address that user specifies Frequency Band Check this option and filter the AP list by the frequency band that user specifies Radio Profile Check this option and filter the AP list by the radio profile name that user specifies This field represents the numerical order of device The MAC address of the AP The model name of the AP The device description of the AP This field can b
52. rder of device Delete Check this option and click Apply to delete the profile Radio Profile Description This field displays the description of the profile Network Mode This field displays the network mode of the profile Channel ID This field displays the channel number of the profile Channel Bandwidth This field displays the channel bandwidth of the profile Tx Power This field displays the Tx power of the profile Data Rate This field displays the data rate of the profile IAPP This field displays the IAPP that is enabled or disabled WMM Capable This field displays the WMM that is enabled or disabled Edit Click Edit hyperlink to re configure the profile Add New 2 4GHz Radio Click the Add New 2 4GHz Radio Profile button to create a new 2 4G Profile radio profile Reply In the delete field check the profile that you want to delete and click Apply to apply the setting Reset Click Reset to cancel the check box of the delete option back to 20 4 4 2 5G Radio Profile User Manual of WAPC 1232HP uncheck status Go to the AP Control gt Radio Profile gt 5G page to create a new 5GHz wireless profile related to wireless advance parameters e System AP Control AP Search Device List SSID Profile Radio Profile 2 4 56 AP Management AP Group Management ID Delete y AP Monitoring AP Status AP Maintenance DHCP Server WAPC 1274327HP 5GHz Wireless Radio Profile Se
53. s 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment User Manual of WAPC 1232HP Federal Communication Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20 cm 8 inches during normal operation R amp TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999 5 CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity R amp TTE The R amp TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment as of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be
54. s button to refresh the list manually 11 User Manual of WAPC 1232HP Apply Click this button to apply the settings 4 3 SSID Profile Go to the AP Control gt SSID Profile page to create a new profile related to wireless SSID WAPC 1232HP System AP Control AP Search Device List gt SSID Profile tet Fa Wireless SSID Profile Settings Radio Profile AP Management KAP Group Management E 4 An x m i AP Monitoring AP Status E oe ID Delete SSID Name SSID Broadcast Security Encryption Client Isolation Edit k i SNMP Add New SSID Profile Port Management Link Aggregation VLANs Figure 4 5 SSID Profile Example of SSID Profile WAPC 1232HP System l T M Add SSID Profile AP Search SSID Configuration Device List SSID Profile Radio Profile AP Management AP Group Management Security Configuration AP Monitoring AP Status Authentication Mode Personal Pre Shared Key AP Maintenance ER EE ad WPA2 Cipher Suite TKIP VI AES ME server Pre Shared Key Format Passphrase SNMP Pre Shared Key 12345678 Port Management Link Aggregation VLANs Figure 4 6 SSID Profile Example 12 User Manual of WAPC 1232HP The page includes the following fields Object Description SSID Configuration This SSID name of the AP SSID Name The length of an SSID should be limited to 32 characters 32 octe
55. ting The page includes the following fields Object Description File Name The file name of the AP s firmware Server IP The IP address of the TFTP Server N Click Browse to specify the firmware file X The firmware file must exist in the directory that TFTP server configured This field shows the current firmware file name and the TFTP server s IP Current address Save Click Save to save the setting 51 User Manual of WAPC 1232HP In this example we use TFTPD32 free TFTP tool P ASE w 4 xample of T Organize Open Burn New folder Documents Date modified a Music Pictures Gi Planet Media Server aes M a W7200AC 1 3465cb150825 bin 9 3 2015 9 21 AM BIM File ideos j Computer lg Local Disk C og Local Disk D DVD RW Drive E Guide wm FF Tftpd32 exe Date modified 5 23 2014 8 09 PM Date created 9 3 2015 9 27 AM Te Application size 188 KB Figure 6 3 TFTP Server Setting copy firmware to the server 52 User Manual of WAPC 1232HP SIE Current Director DATitpd32 Browse Server interfaces 197 158 1 88 Show Dir Titp Server Tftp Client DHCP server Syslog server Log viewer peer ile start time progress total timeo Settings Figure 6 4 TFTP Server Setting set directory and IP TF TP Setting Configured DATftpd321C7200AC 1 3465cb1508 Browse 92 168 1 88 Figure 6 5 TFTP Server Settin
56. tion All rights reserved Figure 1 6 AP Controller Main User Manual of WAPC 1232HP Chapter 2 Assigning IP to Managed APs Before configuring the AP you can configure the AP controller to assign IP address to the managed APs which allow you to manage the APs with ease Step 1 Go to DHCP server gt Mode to switch the Mode to Enabled Then click Apply to apply the setting WAPC 1232HP ver DHCP Server Mode Configuration Mode Excluded IP Global Mode Pool Mode Enabled i Statistics Binding Declined IP VLAN Mode SNMP Port Management Link Aggregation t VLANS gt Spanning Tree Multicast AU Add VLAN Range Figure 2 1 DHCP Server Mode Step 2 Goto System gt Save Startup Config to save configuration Otherwise the DHCP server will return to disabled after system reboot Save Startup Config 4 i p Configuration Download save Running Configuration to startup config Configuration Upload Configuration Activate Configuration Delete Save Configuration Figure 2 2 System Save Startup Config User Manual of WAPC 1232HP Step 3 Goto DHCP server gt Binding to ensure all devices have obtained an IP address successfully WAPC 1232HP system E ES rol Auto refresh L Clear Selected Clear Automatic Clear Manual Clear Expired MI M DHCP Server Binding IP AP Maintenance Binding IP Address SEP 4 E A M Delete
57. to edit and apply the new general setting including the AP description and TCP IP setting Click the Setting hyperlink to apply the 2 4GHz SSID and Radio profiles to the AP Click the Setting hyperlink to apply the 5GHz SSID and Radio profiles to the AP Check this option to let the system refresh the AP list every 15 seconds automatically Click Refresh to query or update the current list Click Apply to save and apply the setting the setting will take effect after about 60 seconds Click Reset to cancel the check box of the remove option back to uncheck status 4 5 1 General Setting Click the Setting hyperlink under the General Setting field to enter the sub menu of AP Management On this page you can edit and apply the new general setting including the AP description and TCP IP setting 28 User Manual of WAPC 1232HP AP General Configuration ID2 AP Information WDAP C7200AC aB f7 20 00 14 6a AP a deep Wi Fi Mac AP day 0 time 0 20 3 AP LAN Setting Configured cwrem DHCP Mode DHCP Client DHCP client 192 168 1 253 192 168 1253 25 55 25 a x 255255 255 0 192 11 192 168 1 254 Enable Figure 4 15 AP Management General Setting The page includes the following fields Object Description AP Information AP Model The model name of the AP AP MAC The MAC address of the AP AP Description The device description of the AP This field length is limited
58. ts normally ASCII letters and digits Select Enable to enable the SSID Broadcasting Broadcast SSID Select Disable to disable the SSID Broadcasting Once disabling the SSID Broadcasting the wireless clients will not able to see the SSID of the AP Select Enable to enable the AP Isolation Select Disable to disable the AP Isolation AP Isolation Once enabling the AP Isolation the wireless clients connected to the same SSID will be isolated Security Configuration Encryption The encryption of the SSID Authentication Mode The authentication mode of the SSID WPA2 Cipher Suite The cipher suite of the encryption Pre shared Key Format The security key format of the SSID Pre shared Key The security key of the SSID Save Save the settings as a new profile Reset Reset the values to default Z The fields on the Security Configuration page will vary according to the encryption you select For a E e detailed description of each field you may refer to the user manual of the AP In this section only the Mi definitions of the fields are described After creating the SSID profile you will see the profile in the list Click Apply to save and apply the setting 13 User Manual of WAPC 1232HP WAPC 1232HP System AP Control AP Search Device List SSID Profile Radio Profile AP Management AP Group Management LA 2 K Wireless SSID Profile Settings AP Monitoring AP Status E E ande ID Delete
59. ttings p p p Radio Profile Description Network Mode Channel ID Channel Bandwidth Tx Power Date rate WMM Capable Add Hew 5GHz Radio Profile Figure 4 11 5G Radio Profile Example of the 5G Radio Profile 91 Device List SSID Profile Radio Profile 2 45 5G AP Management AP Group Management AP Monitoring AP Status AP Maintenance DHCP server SNMP Port Management Link Aggregation VLANS Spanning Tree Multicast OOS Access Control List Authentication Security MAC Address Table LLDP Diagnostics r POE Loop Protection RMON C HELP S User Manual of WAPC 1232HP Add Radio Profile Basic Setting WAPC 1232HP Radio Profile Description Auto Block Ack Decline BA Request HT Disallow TKIP Channel Bandwidth Mcs HT TxStream HT RxStream 56Hz Radio Profile 11a ac n mixed mode Mixed ble Disable Disable Advanced Setting 5GHz Radio Profile Auto 11a ac n mixed mode mixed mode Disable Disable Disable Disable Disable od Long Auto BG Protection Mode Beacon Interval 20 1024 ms 100 Data Beacon Rate DTIM 1 255 1 Fragment Threshold 256 2346 2345 RTS Threshold 0 2347 2347 Short Preamble Disable Short Slot Enable Pkt Aggregate WMM Capable APSD Capable DLS Capable Enable Disable Disable Multicast to Unicast IAPP TX Beamforming Enable
60. user specifies Sms AP MAC Address Check this option and filter the AP list by the MAC address that user specifies SSID Check this option and filter the AP list by the SSID name that user specifies Band Check this option and filter the AP list by the frequency band that user specifies ID This field represents the numerical order of device AP MAC Address The MAC address of the AP AP Model The model name of the AP Device Description The device description of the AP This field can be modified through the Setting hyperlink under the sub item 43 User Manual of WAPC 1232HP General Setting Band The frequency band of the AP SSID The SSID name of the AP Channel Number The channel number of the AP Encryption The encryption of the AP BSSID The basic service set identification BSSID of this VAP Associated Clients The client number associated to this VAP SSID Broadcast Displays the SSID Broadcast option that is enabled or disabled in this VAP musa EST Check this option to let the system refresh the AP list every 15 seconds automatically Refresh Click Refresh to query or update the current list 5 3 Radio Summary Go to AP Monitoring AP Status Radio Summary to check each Radio configuration status of the managed APs in the Device List Radio Summary Query by C AP Model AP MAC AP Model Device Frequency Radio Profile Network Channel Channel Tx Data WMM Address Description Band Descripti
61. usly Option 1 or 2 Default is 2 You can adjust the wireless transmit power here By reducing the TX power you can reduce the wireless coverage to make it only cover the area you need Default is 100 Advanced Setting BG Protection Mode Beacon Interval 20 1024 ms Data Beacon Rate DTIM 1 255 Fragment Threshold 256 2346 RTS Threshold 0 2347 Short Preamble Short Slot In IEEE802 11b g mixed environment IEEE802 11g has priority over IEEE802 11b on the connection Auto STA will dynamically change to AP announcement On IEEE802 11g is used first on the connection Off In IEEE802 11b g mixed environment take slower conditions Default is Auto The interval of time that this access point broadcasts a beacon Beacon is used to synchronize the wireless network Default is 100 This is the Delivery Traffic Indication Map It is used to alert the clients that multicast and broadcast packets buffered at the AP will be transmitted immediately after the transmission of this beacon frame Default is 1 if not supported it will display O You can specify the maximum size of packet during the fragmentation of data to be transmitted If you set this value too low it will result in bad performance Default is 2346 When the packet size is smaller than the RTS threshold the access point will not use the RTS CTS mechanism to send this packet Default is 2347 The
62. vironment Default is Disabled A mechanism that allows a unit with only one antenna to leverage STBC multiple antennas on other 802 11n devices to improve performance and range Default is Disabled An aggregation technique which prevents sending Ack in the Auto Block Ack communication to reduce the network congestion If this option is enabled the device will try to activate this function when transmitting massive data Default is Disabled Enable thi i line the Block Ack by th Decline BA Request nable this option to decline the Block Ack request addressed by the other devices Default is Disabled HT Disallow TKIP Prevents the use of TKIP data encryption when using 802 11n high throughput data rates Default is Disabled The channel bandwidth of the 2 4GHz wireless interface Default is 40 Channel Bandwidth Guard intervals are used to ensure that distinct transmissions do not Guard Interval interfere with one another Only effective under Mixed Mode Default is Long The Modulation and Coding Scheme MCS is a value that determines MCS the modulation coding and number of spatial channels Default is Auto Ea HT Tx Stream HT Rx Stream Tx Power User Manual of WAPC 1232HP HT means High Throughput The number of HT TxStream means how many antennas will transmit data simultaneously Options 1 or 2 Default is 2 The number of HT RxStream means how many antennas will receive data simultaneo
63. yperlink of IP address to link to the AP s Web UI directly In addition if this device is not the AP that you want to manage you can check it in the delete field to remove it from the list A maximum of 32 devices can be added on the Device List page WAPC 1232HP System AP Control AP Search Device List SSID Profile Radio Profile AP Management AP Group Management Device List AP Monitoring AP Status 4 ID MAC Address AP Model Device Netmask Device Gateway Device Description gt cup 4 a8 f7 e0 00 14 6alWDAP C7200AC 1 3465cb 150804192 168 1 253 255 255 255 0 192 168 1254 WiFi ttacAP O Port Management Link Aggregation VLANs Figure 4 4 Device List The page includes the following fields Object Description ID This field represents the numerical order of device MAC Address The MAC address of the AP AP Model The model name of the AP Version The current firmware version of the AP The IP address of the AP Device IP On the Device List page the IP address is a hyperlink which enables the user to link to the AP s Web configuration page directly Device Netmask The netmask of the AP Device Gateway The gateway IP address of the AP Device Description The device description of the AP Delete Check this option to remove the device from the managed AP list Auto Refresh Check this option to let the system automatically refresh the list every 15 seconds Refresh Click thi

User Manual of AP Controller - PLANET Technology Corporation.

Contents

Download Pdf Manuals

Related Search

Related Contents