User Manual ENG
Contents
1. One 3 V Lithium battery type 2L76 or DL1 3N 1000 10 000 h typically 10 years at CompM2 NVD position CompM2 ML2 130 mm 5 1 Battery life hours Length incl lens covers Width height Weight incl lens covers Adjustment Mounting Max temperature range Water resistance CompM2 ML2 49 mm 1 9 CompM2 ML2 200 gram 7 1 oz Range 2 m at 100 meters in windage and elevation 1 click 13 mm at 80 m 16 mm at 100 m 1 2 at 100 yds One wide ring 30 mm diameter or Aimpoint QR Ring 45 C to 70 C 50 F to 160 F Submersible to 25 m 80 ft 1 3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS See fig 1 Sight Battery Cap Rotary Switch Lens Cover rear oe ee ee eS Se Lens Cover front NVD Night Vision Device Cap Adjustment 2 pcs Battery DL1 3N or similar Strap for Cap Adjustment 2 pcs Adjustment Screws Windage Elevation 2 pcs MOA Minute Of Angle 1MOA 30 mm at 100 meters 1 at 100 yards Average values depending on brightness setting Comp M2 ML2 Right handed shooter configuration Left handed shooter configuration Fig 1 CHAPTER II OPERATION UNDER NORMAL CONDITIONS 2 1 ASSEMBLY AND PREPARATION FOR USE WARNING Ensure that the weapon is unloaded and the safety selector is in the safe position before attempting to install remove or perform maintenance on the sight 2 1 1 Installing Battery2. a Remove battery cap 2 by turning it counter clockwise b Insert battery 3 with positive end toward cap CAUTION When replacing battery not necessary when the sight is unused check that the O ring is present and not damaged Failure to do so could result in water leakage into the battery compartment c Install battery cap 2 by turning clockwise until snug Hand tighten only Using tools can damage equipment d Verify that the red dot is present by turning the rotary switch clockwise 2 1 2 Installing Ring and Sight on the weapon Aimpoint s sights are designed for installation on most types of weapons If your weapon does not have or support an appropriate base s please consult your dealer gunsmith or other qualified source a Assemble the sight to the weapon by using Aimpoint s wide 30 mm ring or QR mount If other standard 30 mm rings are used make sure that the ring s covers a length of minimum 25 mm or 1 two standard rings could possibly be used b Ensure that the sight is correctly positioned for right or left hand shooting Aimpoint sights can be installed to support either right hand fig 2 or left hand fig 3 shooters c When using lens covers 8 amp 9 ensure that they are correctly positioned and can be opened NOTE make sure that you have space between the bottom front part of the sight and the top of the base weapon d Finally make sure that all screws are firmly tightened around t
3. com www aimpoint com THE FUTURE IN SIGHT Copyright 2015 Contents property of Aimpoint All rights reserved 10590 5 CHAPTER I PRESENTATION 1 1 PRESENTATION Aimpoint s Reflex Sights are rugged precision electronic optical red dot sights developed for civilian military and law enforcement applications Aimpoint sights are designed for the two eyes open method of sighting which greatly enhances situational awareness and target acquisition speed Thanks to the parallax free design the dot follows the movement of the user s eye while remaining fixed on the target eliminating any need for centering Further the sight allows for unlimited eye relief The CompM2 is compatible with 1st 2nd and 3rd generation night vision devices while the CompML2 is optimized for applications which do not require night vision compatibility 1 2 SPECIFICATION Material housing Extruded high strength aluminum anodized Surface finish Hard Anodized Dark Graphite Grey matte Material lens covers Thermoplastic elastomer black non glare Optical magnification 1X Eye relief Unlimited no centering required Optical coating Anti Reflex coating all surfaces Multi layer coating for reflection Band Pass coating for NVD compatibility CompM2 Dot size 4 MOA Switch dot brightness CompM2 10 positions 4 NVD 6 daylight of which 1 Extra Bright CompML2 10 positions 1 Off 9 daylight of which 1 Extra Bright Battery
4. 2 2 OPERATING PROCEDURES 2 2 1 Zeroing Aimpoint s sights are delivered in a centered position Normally this means that only small adjustments are necessary providing that the base s are properly aligned CAUTION Do not continue to adjust windage and elevation mechanisms if you encounter resistance The elevation Adjustment screw is located on top of the sight while the windage screw is located on the right or left side depending on how the sight has been mounted on the weapon Aimpoint sights can be installed to support either right hand fig 2 or left hand fig 3 shooters a Open Front and Rear Lens covers 9 and 8 b Turn the Rotary switch 4 clockwise until the red dot has a sufficient intensity to contrast against target NOTE Each click of the Adjustment screws 7 corresponds to a 13 mm movement of the point of impact at 80 meters 4 mm at 25 meters 16 mm at 100 meters and 32 mm at 200 meters or 1 4 at 50 yds 1 2 at 100 yds and 1 at 200 yds c Insert adjustment tool coin screwdriver knife or cartridge casing in Adjustment screw slot 7 and turn as follows e To move the point of impact to the right turn windage adjustment screw counter clockwise clockwise if screw located on left side e To move the point of impact to the left turn windage adjustment screw clockwise counter clockwise if screw located on left side e To move the point of impact up turn elevation adjustment screw counter
5. clockwise e To move the point of impact down turn elevation adjustment screw clockwise d Confirm zeroing by firing at least three shots at a zeroing target Check impact points on zeroing target to confirm accuracy and repeat above procedure if required e After initial firing ensure that the mount and sight are secure Turn Rotary switch 4 to OFF position counter clockwise g Close front and rear Lens cover 9 and 8 a CHAPTER IlI OPERATION UNDER EXTREME CONDITIONS a Extreme heat moist or dry No special procedures required b Extreme cold Extreme cold might shorten battery life Keep spare batteries in your inner pockets to keep them warm c Salt air No special procedures required d Sea spray water mud and snow Ensure that the Battery cap 2 and the two Adjustment screw caps 5 are tight before exposing the sight to sea spray mud snow or before submersing the sight into water Hand tighten only Keep lens covers closed when the sight is not being used Clean lenses with lens paper cloth and wipe the sight dry as soon as possible after exposure to water sea spray mud or snow e Dust storms and sand storms Keep lens covers closed when the sight is not being used f High altitudes No special procedures required CAUTION The lenses shall never be cleaned with fingers but with lens paper cloth If lens paper cloth is not available To clear away debris sand grass etc blow away the dir
6. he sight e Complete the zeroing 2 2 1
7. t or rinse with clear water To clean lenses mist up the lenses or rinse with clear water and clean them with a soft piece of cloth CHAPTER IV TROUBLE SHOOTING PROCEDURES 4 1 RED DOT DOES NOT APPEAR Discharged battery Replace Battery 3 Battery installed incorrectly Remove and reinstall Battery 3 with toward Battery cap 2 Clean contact surfaces and reinstall Battery 3 Battery is not making good contact Defective rotary switch Notify dealer armourer 4 2 IMPOSSIBLE TO ZERO Adjustment screw is at its limit Check alignment of mount to barrel Impact point is moving Check mount stability CHAPTER V MAINTENANCE a This reflex sight does not require any particular maintenance while used under normal conditions b Under severe weather conditions please refer to CHAPTER III Keep Lens covers 8 and 9 closed whenever the sight is not in use d Warehouse storage Remove Battery 3 and allow lens surfaces to dry completely if wet before closing the Lens covers 8 and 9 e To clean lenses refer to CAUTION in CHAPTER III O Ix Aimpoint User Manual for Aimpoint CompM2 and Aimpoint CompML2 Aimpoint AB Jagershillgatan 15 SE 213 75 Malmo Sweden Phone 46 0 40 671 50 20 Fax 46 0 40 21 92 38 e mail info aimpoint se www aimpoint com Aimpoint Inc 14103 Mariah Court Chantilly VA 20151 2113 USA Phone 1 703 263 9795 Fax 1 703 263 9463 e mail info aimpoint
Download Pdf Manuals
Related Search