Installation Guide
Contents
1. Position a wall jamb against the wall directly over the bottom track The wall jamb should sit flat against the wall Slide the wall jamb down over the bottom track until the wall jamb and bottom track are fully engaged NOTE The wall jamb must sit flat on the bottom ledge If your ledge has a curve in the corners at the side wall it may be necessary to shape the bottom end of the wall jamb with a file Use a level to align the wall jamb vertically and mark the hole locations on the wall Repeat the procedure with the other wall jamb Remove the bottom track and wall jambs NOTE When installing on ceramic tile use a center punch to nick the surface of the glaze Tap the center punch lightly with a hammer to avoid cracking the tile Lightly center punch the hole locations Drill a 3 16 hole at each mark Use a masonry bit for ceramic tile Thoroughly clean the shower floor ledge and wall Insert plastic anchors in each hole Sterling 7 1034034 2 A Caulk Here Sg Groove Bottom Track 4 Caulk the Bottom Track Remove the bottom track from the shower ledge Apply a bead of caulk in the groove on the underside of the bottom track Apply a second smaller bead of caulk to the other edge on the underside of the bottom track Install the bottom track on the ledge at the marked location 1034034 22. A 8 Sterling Measure Here Screw Top Track 8 18 x 1 1 2 Panhead Screw e 5 Install the Wall Jambs Place a wall jamb over the bottom track Align the holes in the wall jamb with the holes in the wall Secure the wall jamb to the wall with three 8 18 x 1 1 2 panhead screws Repeat with the second wall jamb Install screw covers over the top and bottom screws in each wall jamb 6 Install the Top Track NOTE The top track is designed so either side may be positioned facing outward according to your preference Measure the distance from wall to wall at the top of the wall jambs This is the length to cut the top track Mark the top track at the determined cutting dimension NOTE For best results use a miter box and 32 tooth per inch hacksaw to make the cut NOTE Cut the top track on the inside edge of the mark 1 32 1 mm to allow space for the top track to slide into place easily Cut the top track o File the rough edges smooth where the top track was cut taking care to avoid damaging finished surfaces Position the top track over the wall jambs and gently push down Sterling 9 1034034 2 A Aq 8 32 x 3 8 Hex Top Frame Washer Head Flange Screw Outside Panel Bottom Frame _Leg a 8 32 x 3 8 Hex Washer sosta Head Screw Tab maler mo Y Handle Sid
3. 1034034 2 A Installation Guide Bypass Shower Doors SP5900 Series STERLING A KOHLER COMPANY Tools and Materials o O NS Plus Silicone Masking Tape Drop Cloth Sealant Tape Measure Pencil amp Felt Tip Marker Center EO Punch File Safety Glasses J T DC SA LA 0 Assorted Miter Saw or i Saw Screwdrivers Knife With 32 Teeth Per Inch Caulk Gun Pliers Hammer Thank You For Choosing Kohler Company We appreciate your commitment to Sterling quality Please take a few minutes to review this manual before you start installation If you encounter any installation or performance problems please don t hesitate to contact us Our phone numbers and website are listed on the back cover Thanks again for choosing Sterling Before You Begin CAUTION Risk of injury Always wear safety glasses when cutting or drilling CAUTION Risk of injury or product damage Tempered glass cannot be cut IMPORTANT This shower door is designed to be specifically paired with a Sterling shower module Do not install this shower door if you do not have a Sterling shower module installed IMPORTANT Pay special attention to the section titled Very Important Instructions Failure to follow the directions could result in product damage IMPORTANT Some of the models in this series of door have two sets of wall jambs enclosed tapered style and non tapered style Match the proper style to your install
4. Install the Inside Door Panel NOTE Perform these installation steps from outside the shower Install the inside panel first NOTE When installing the inside panel lift the panel with the handle side toward the inside of the shower and slide the rollers into the top track o Lift the door panel Hang the rollers on the appropriate rail on the top track Make sure the bottom of the door panel sits inside of the bottom track Check the panel for proper alignment and smooth operation If adjustment is needed remove the panel Loosen the roller screw s and move the roller s in the slot to align the panel Tighten the screws and reinstall the panel Repeat the procedures with the outside door panel Align the inside panel with the wall jamb on the showerhead side of the shower Sterling 11 1034034 2 A Inside Panel Guide Bushing Installed D No 8 18 x 3 8 Frame LS Panhead 4 __Screw Bushing Crimp Here on X Each End 10 Install the Seal Install a bushing into one end of the inside panel guide Measure the length of the panel guide subtract 1 2 5 cm and cut the seal to the resulting length Slide the seal into the panel guide Install a bushing into the other end of the panel guide Use a pliers to crimp each end of the panel guide to keep
5. ation and discard the extra set If you receive only one set of wall jambs follow the tapered wall jamb directions when cutting NOTE When using a retractable case tape measure make sure you add the length of the case to the measurement or measure in a manner that excludes the case Before starting the installation lay out and identify the parts Inspect them for damage Once inspected return the glass panels to their packaging and place them in a safe area until they are needed The bath shower or receptor should be installed prepared at this time including finished wall materials 1034034 2 A 2 Sterling No N Screw Cover Wall _Jamb ne Sl 5 Bumper 2 LP x SS Anchor Tap 9 Outside Panel Bushing Parts Identification A Wall Jamb Mounting Screw 8 18 x 1 1 2 Panhead Roller Screw Roller Towel Bar Bracket Screw 8 Towel 18x 3 4 Bar Panhead Towel Bar Bracket 2 UA A Screw Cover Outside Panel Screw Cover 0 0 Inside Panel Guide dE Inside Guide Bushing e a N Top Track Roller Screw Wall Jamb Mounting Screw 8 18 x 1 1 2 Panhead Anchor Wall Jamb 8 18 x 3 8 Panhead Screw Sterling 1034034 2 A CAUTIONI Most Common Installation Mistake Do not cut the
6. e of Door Panel Side Groove Frame Inside Panel Bushing Installed into the Bottom Fame 7 Install the Rollers Outside Panel NOTE The steel side of the roller must be installed against the top frame flange Place the rollers on the top frame flange The roller should face the bottom frame leg Secure the rollers to the top frame flange with 8 32 x 3 8 hex washer head screws Lay the outside door panel on a flat surface taking care to protect the glass Cut two 7 8 2 2 cm long pieces of the provided adhesive tape o Remove the protective paper from the adhesive side of the tape and attach the tape to the bushings With the bushing tab toward the bottom frame groove pinch the bushing legs together and push down until the bushing tab snaps into the bottom frame groove Locate the bushings 1 4 6 mm from each end on the bottom frame of the outside panel 8 Install the Rollers Inside Panel NOTE The steel side of the roller must be installed against the top flange frame o Place the rollers on the top frame flange facing the handle side of the door panel side frame Secure the rollers with 8 32 x 3 8 hex washer head screws 1034034 2 A 10 Sterling Inside Rail Outside Rail Outside Panel Handle Side of Inside Panel Toward Inside of Shower Bottom Track Leg 9
7. mension For best results use a 32 tooth hacksaw blade and a miter box If you are using the tapered wall jambs subtract 2 1 2 6 4 cm from dimension D and cut the bottom track to this dimension For best results use a 32 tooth hacksaw blade and a miter box o File the rough edges smooth where the bottom track was cut taking care not to mar the finished NOTE If there are curves where the sidewalls meet the threshold contour the bottom track edges to Measure Here gt Angled Base Sterling 5 1034034 2 A Bottom Track Leg Toward __ Outside of Shower Se Space to Be Same on Each End Bottom Track 2 Locate the Bottom Track NOTE The track must sit flat If the ledge has a curve in the corners or is constructed of fiberglass it may be necessary to shape the ends of the track with a file o Place the bottom track on the flattest part of the ledge with the leg toward the outside of the shower Situate the bottom track so there is an equal gap between each wall and the ends of the track and temporarily fasten the track to the ledge with masking tape Mark the ledge along the front edge of the track with a soft pencil 1034034 2 A 6 Sterling If Necessary Shape Bottom End of Wall _Jamb Anchor Bottom Track Leve i Benai A enci Wall Jamb Fully Engaged with Wall Bottom Track Jamb 3 Mark the Wall Jamb Locations
8. the bushings from sliding off 11 Install the Panel Guide NOTE Perform these installation steps from inside the shower Install the panel guide in the opening in the bottom track Align the slots on the panel guide with the holes in the inside bottom frame Loosely thread two 8 18 x 3 8 panhead screws through the guide and into frame Do not tighten at this time Push the guide all the way into the bottom track Lower the guide slightly for clearance and tighten the screws Move the panel back and forth along the full width of the opening If the panel sticks loosen the screws and adjust the guide Repeat until the door operates smoothly Install screw covers over the panel guide screws Install screw covers over the four frame screws at the bottom of the panels 1034034 2 A 12 Sterling Towel Bar Install Towel Bar on Room Side of Panel Outside Panel Frame Towel Bar Si Cover Bracket Na So Inside of Shower 8 18 x 3 4 Inside of shower Panhead Screw 12 Install the Towel Bar NOTE The towel bar is designed for either side to face out O Determine which side of the towel bar will face out Insert a towel bar bracket into each end of the towel bar Align the towel bar and brackets on the room side of the outside panel o Secure the towel bar to the panel with two 8 18 x 3 4 panhead screws Install screw covers over
9. the screws 13 Final Caulking NOTE Thoroughly clean and dry all dust dirt and grease from the bottom track and shower ledge surfaces where caulk will be applied Carefully caulk where A the wall jambs and wall meet inside the shower B the bottom track and wall jamb join C the inside of the frame where the wall jambs and bottom track meet Allow the sealant to cure following the sealant manufacturer s instructions before using the shower Sterling 13 1034034 2 A 1034034 2 A 1034034 2 A Phone 1 888 STERLING 1 888 783 7546 SterlingPlumbing com STERLING A KOHLER COMPANY 2004 Sterling 1034034 2 A
10. top and bottom track the same length for this installation Please read these installation instructions carefully before cutting the top and bottom track If uncertain about cutting tracks please contact a customer service representative at 1 888 783 7546 for help Very Important Instructions 1034034 2 A 4 Sterling Measure Here Measure distance Fa D above curves in the comers D Curved Base 1 Measure and Cut the Bottom Track or angle could result in the bottom track being cut too short enclosed Follow the directions for the proper wall jambs surface match the curves Warni ng Measure carefully If your walls are curved or angled measure above the curve or angle Failure to do so can result in an improperly cut bottom track and can void the warranty CAUTION Risk of product damage If your shower has a curve in the corners where they meet the sidewalls be sure to measure from wall to wall above the curves Failure to measure above the curve CAUTION Risk of personal injury Always wear safety glasses when cutting materials IMPORTANT This model of shower door may have both a tapered and straight style of wall jamb Measure from wall to wall at the flattest part of the shower ledge dimension D If you are using the straight wall jambs subtract 1 8 3 mm from dimension D and cut the bottom track to this di
Download Pdf Manuals
Related Search