FULLY ARMING THE SYSTEM – ON MODE
Contents
1. Central Station Location where alarm data is sent during an alarm report Chime Feature An option that allows the code pad to sound a ding dong whenever an entry exit door is opened Codes Can be either User Codes relating to a person or Function Codes a toggle switch to turn specific functions on off NOTE A system may have either 99 four 4 digit codes or 66 six 6 digit codes but not a mixture of the two Dialer Delay An option that allows a delay in reporting to the central station Duress Code An option that allows a special code to be sent to the central station that indicates the alarm system is being operated under duress Forced Arming An option that allows the system to be turned on ARMED with one or more zones open A System that is ready to be force armed will flash the ready light Note Those zones that are not ready will not create an alarm Function Code A Function Code is either a four 4 or six 6 digit code that has been programmed by the installer to operate a device Group Bypass An option that allows the user to bypass multiple zones with a single operation Master Code A master PIN code that can arm amp disarm the alarm system and can add and delete user PIN codes Partial Arm A mode used to arm the perimeter and unused areas of an occupied premises Perimeter The outer edge of the protected area typically the windows and doors fitted with alarm sensors Quick Arm An opt2. CODE PAD CONTROL TONES s Beeps for all key presses Sounds a continuous tone during the entry delay time s Pulses when a day zone is violated while the system is disarmed e Pulses when a fire zone has a trouble condition s Beeps 3 times for trying to arm with the Ready light off if Force Arming has not been selected s Beeps for 1 second or emits a ding dong sound for the Chime feature L Beeps during an exit delay beeps rapidly for the last 10 seconds of an exit delay and beeps 1 second at the end of the exit delay s Pulses when the armed status changes and the AC power is off s Pulses when the armed status changes and any zone s is bypassed s Pulses when the armed status changes and a low battery is detected s Pulses when the armed status changes and a tamper condition is detected Beeps to indicate telephone line cut if selected s Pulses when one or more of the following conditions are detected zone or box tamper low battery AC power fail or expander trouble Entering a valid code will silence the code pad sounder when it is pulsing Please contact your installer if a trouble condition exists Page 6 V2 03 FULLY ARMING THE SYSTEM ON MODE ON is used when the user is away from the premise and wants the interior protected To arm in the ON Mode Close all protected doors and windows Ready light will light when all protected zones and sensors are secure NOTE If a
3. Partial Mode sese eee eee ee eee eee 8 V Disarming from the On or Partial Mode sss esse eee eee eee 8 V Bypassing Individual Zones sss eee eee eee eee ee eee 9 Group Bypass oci pe Diane ce E EE eR Pee Ea x 10 e Changing amp Adding User Codes sss essere eee 11 e Deleting User Gode uoce oe ee re C eet eee tee T eed tad 12 LEER IIS c 12 User Code Authorisation sisses nennen nennen 13 e Setting the Door Chime isses ete eee t het ae ebat 13 Exit Mode Extend Exit Timer sess 14 s Code Pad Emergency Keya sse sees ee eee eee ereer 14 e Viewing Alarm Memory eee ee ee eee ee eee eee ee eee ee 14 e Reset Latched Alarms eese nnne nnne nente 15 Setting System Date nennen nennen nennen nns 15 s Setting System Time eee eree eree eee neee 16 s Set Code Pad Tones sss eser eee 16 V Program Telephone Number sss eee ee eee eee eee e 17 e Viewing Telephone Numbers sese eee eee eee eee ee eee eee 18 e Cancelling Alarm Calls sese 18 Deleting Telephone Numbers essen nennen 19 U Communicator Battery amp Siren Test 19 e Service Lights uat e piter e n ten tee a eoe tt de oi e edet 20 V Emergency Evacuation Plans 21 LOMO R L P Back Page Page 3 V2 03 GLOSSARY OF TERMS Authority Level The level of access an individual has when using an alarm panel
4. Press Exit key to extend the exit time Code Pad Emergency Keys Three 3 emergency features are available to be programmed into your code pad to provide support in the areas of personal safety Medical Police duress and Fire arm You must hold these keys for two 2 seconds to activate these functions You should press these keys only in an emergency situation that requires response by emergency personnel Check with your security installation company to find out if your system is programmed for these activation keys Key Sequence Press this key and hold for two 2 seconds to activate the fire alarm Press this key and hold for two 2 alis seconds to activate the medical auxiliary alarm Press this key and hold for two 2 c seconds to activate the police duress panic hold up alarm VIEWING ALARM MEMORY Whenever an alarm activation occurs on your system all zones that were in alarm during that activation will be held in memory The last alarm activation can be reviewed via the function listed below l e You can see which area has activated the alarm Key Sequence The alarm memory feature will flash gt those zone s that created alarms and will light steady the zones that were bypassed during the last alarm Page 14 V2 03 RESET LATCHED ALARMS Reset Latched Alarms function resets smoke
5. exit delay before the delay expires Fire Light A steady fire light means a fire zone has been faulted A rapidly flashing fire light means that a fire zone is in a trouble condition On Light The on light is on when the system is armed The on light is off when it is disarmed Partial Light The partial light is lit when the system is armed in the Partial Mode All non bypassed zones will be delayed and follow the Partial delay time When armed in Partial Mode the Arm On and Bypass lights will also be lit Power Light The power light is lit if the primary power is on The power light will flash if the system detects a low battery condition Ready Light The ready light is lit when the system is ready to arm and flashes if ready to force arm The ready light is off when the system is not ready to arm because of a zone s being faulted Zone Light The zone lights are off when everything is normal A zone light will be lit if the zone has been bypassed If a zone light is flashing that zone is in alarm or has been faulted If a zone light is flashing rapidly it means that the zone is in a trouble condition Trouble conditions are Hardwire Zone Tamper Wireless Zone Tamper Sensor Low Battery and Sensor Loss of Supervision A combination of Alarm Fault and Tamper Trouble will produce a rapid flashing light for a short period of time followed by a slow flashing light Page 5 V2 03
6. to be deleted e g user code 03 4 Press the Chime key four 4 times to delete the user code 5 Repeat steps 3 and 4 for additional user codes 6 Press when completed WALK TEST function correctly Walk test is used to test the functionality and should be performed regularly When in walk test mode the code pad transmits the chime sound each time a zone is activated and will light the activated zone number in the code pad for the duration of the walk test period You must exit the walk test mode when you have completed testing or are satisfied the zones Note the alarm system will not report to the control room during the walk test Key Sequence oco oooo P 1 Press CHIME 2 Enter a master code The system is now in walk test mode 3 Walk past each motion sensor and return to the code pad to check each zone light to validate the sensors are working correctly 4 Enter a master code to exit walk test If no master code is entered walk test mode will automatically exit in 15 minutes Page 12 V2 03 USER CODE AUTHORISATION Any user code can be assigned the master code status to allow that user to change or add other codes and provide access to other system functions Key Sequence O Example shows enabling user two 02 as a master code 12A A A 2 Enter an existing master code
7. Fitts er 5 0 2 e eee e ise eee vmm e eoe Uc GO UD 70 SEB HILLSe Series LED Code Pad User Manual Not all features may be available on your system Check with your installer to find out which features are programmed uw L SAJA NOILVALLOV AONSSYSWS LL SAJA AYLIN 3002 H398WN 0 suogounj snoueA woed SAIM NOILONNAS uiejs s 1no YM uonipuoo ejqnoJ e ejeoipur ouo SI 1UBrn 221049395 WUE 9210 0 Apeal s uiejs s y u ym uo SI 346 AQV3SH UOnpuoo 92lAIeS JO USRI SPJ yne euoz JO ysey Mo s ssed q ejeoipui 0 peejs uo ale SLH9IT INOZ 8v GI INOZ LNO 11Nd uiejs s easy INOA YUM UOnipuoo aqno e ejeorpul 0 s yse wieje 3114 ayeo pul 0 uo S 3ubr1 3313 p ej p aq jim seuoz pessed q uou v POW eed eui ur peuue si ulejs s Y ueu UO si 446 TWILYWd wee snoi eJd e ejeoipur 0 seuse 4 peulJesip uaym yo pawie UaYM uo SI 348 NO uonipuoo Meng moj e 8jeoipur 0 seusej ueseiJd si Jamod OW ueuM uo si 3uBr1 YAMOd ob St vi EL ana 6 9 8 gt E 8 v V2 03 Page 2 TABLE OF CONTENTS s Code Pad Diagrams sss eee eee 2 e eT 21 RT 1 TT 4 s Understanding the Code Pad Lights see 5 Code Pad Control Tones essent nennen 6 s Fully arming the system On Mode esee 7 e Fully arming the system Quick Arm Mode eene 7 e Partially arming the system
8. O 3 Enter the user code to have changed to a master code e g User code 02 4 Press 4 key LED 4 will light up to indicate the user is now a master code If LED 4 is not lit then it is a normal user code 5 Repeat steps 3 and 4 for additional user codes c 6 Enter 7 Enter when completed SETTING THE DOOR CHIME Chime Mode provides only an audio warning at the premises A ding dong is sounded from the code pad when the protected area is entered for example when an infant opens the door The door chime is turned on or off by pressing the CHIME key while the system is in the disarmed state If the chime is on the chime light will be lit If the chime is off the chime light will be off Each press of the CHIME key will toggle the chime feature on off Chime mode must be programmed by your security Installation Company Tell the installer if Chime mode is required for any areas Key Sequence Press the CHIME key to turn on or turn off the chime feature Page 13 V2 03 Exit mode is used when you have already armed your Security System but need to extend your exit time Pressing the exit button will re start your exit time but you may only press Exit button twice The code pad will beep faster in the last ten 10 seconds as a warning Key Sequence EXIT MODE EXTEND EXIT TIMER
9. UBLE Press the 5 key and the zone light s will illuminate showing which zone s has a trouble condition Press the 7 key to return to the 1 of 8 service lights TELEPHONE LINE TROUBLE LINE CUT There is telephone line trouble or the telephone line has been cut The service light will remain lit until the telephone trouble clears and a user code is entered Note This fault is global in nature and will affect all areas of a multi area system FAILURE TO COMMUNICATE There is a failure to communicate between your System and the central station Note This fault is global in nature and will affect all areas of a multi area system LOSS OF SYSTEM TIME There has been a loss of power and your system clock needs to be reset Instructions are on page 15 Note This fault is global in nature and will affect all areas of a multi area system To exit the Service Light Mode press the key Page 20 V2 03 EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition For example the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building Draw up a floor plan of your home Show windows doors stairs and rooftops that can be used for escape Indicate each occupant s escape routes Always keep these routes free from obstruction Determi
10. Y IS REPLACED BY AN INCORRECT TYPE DISPOSE OF BATTERIES ACCORDING TO THE INSTRUCTIONS CONTACT YOUR INSTALLER FOR REPLACEMENT BATTERIES When installed as directed this product conforms to the standards set by Standards Australia on behalf of the Australian Communications Authority ACA 007573417 Hills LED Keypad User Manual Programmed Phone Number 1 Programmed Phone Number 2 Programmed Phone Number 3 ENTRY EXIT 24 STAY MODE 24 HOUR ZONE LIST 9 ON o0 H WN oca WOW ND PO 16 N N DNN a on oO wq ON N A For Service Contact
11. detectors zone troubles and zone tampers alarms Note If the code pad begins beeping the reset did not execute properly Enter your code to silence the code pad Wait a few minutes and repeat the reset function to attempt another reset If the code pad still beeps after repeated attempts please contact your installer 1 Enter you code to silence the code pad sounder nh 2 Press 7 to activate the reset function SETTING SYSTEM DATE Key Sequence Example shows setting date as Monday June 11 2007 1 Press 9 6 keys 4 e 2 Enter the master code 3 Enter the day of the week Ey 1 Sunday 7 Saturday 4 Enter the month code Must be lt p gt O two 2 digits E g 0 6 for June 5 Enter the day code Must be two em Ge 2 digits E g 1 1 for the 11 day 6 Enter the last two 2 digits of the lt p gt e year code E g 0 7 for 2007 gt 7 Press to exit Your date is now set Page 15 V2 03 SETTING SYSTEM TIME Key Sequence Example shows setting time at P O Da 1 Press 9 7 keys b c 2 Enter the master code 3 Enter the hour code Must be two lt gt lt p gt 2 digits E g 0 9 for 9am 4 Enter the minutes code Must be ED lt p two 2 digits E g 3 0 for 30 minutes D 5 Press to e
12. ed exit path Note The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire Key Sequence Example shows ON key being used to set the system to the Quick Arm Mode Page 7 V2 03 PARTIALLY ARMING THE SYSTEM PARTIAL MODE Partial arming allows you to temporarily exclude some rooms from security arming For example you may wish to exclude bedrooms at night when they are in use Partial mode is also used for protecting exterior doors and windows the home perimeter when the user is inside Partial is used when the user is inside the premise and wants protection around the perimeter Listed below are the steps to arm in the Partial mode Close all protected doors and windows Ready light will light when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light The security system will not arm if the ready light is not on If the power light is off you have no AC power Restore power if possible If not contact your installation company Press the PARTIAL key The bypass light will illuminate if any zone s is bypassed The light s corresponding to the bypassed zone s will illuminate alerting the user that a zone s may be unprotected and can be faulted without an alarm Key Sequence Operation Press
13. ion that allows you to turn on ARM the security system by pressing either the ON or PARTIAL key on the code pad control for ARMING only as programmed by the installing company Universal Arming Uni Arm When enabled your alarm system can automatically determine whether to arm in the Full mode or in the pre set Partial mode by looking to see if you exit your premises or stay inside after arming your system NOTE This feature can be used in conjunction with Quick Arm User Code A four 4 or six 6 digit entry used to arm or disarm the system Page 4 V2 03 UNDERSTANDING THE LIGHTS Armed Light The armed light is on when the system is armed The armed light is off when it is disarmed The armed light will flash when there has been an alarm during the previous arm cycle Bypass Light The bypass light is on when any zone in this code pad s area is bypassed The zone s that is bypassed will also be illuminated If the bypass light is off no zones are bypassed Chime Light The chime light is on when the chime feature is on off otherwise Exit Light The exit light is on during the exit delay Please note that the light will flash during the last 10 seconds of the exit delay as a warning that the time is running out The user may want to restart the exit delay if the exit light is flashing in order to prevent an alarm The user may then press the Exit key to restart the
14. m gt EDP 2 Enter the master code 3 Enter the phone number not exceeding twenty 20 digits Use the table below to determine the key values 4 Press to end and exit Key Phone Digit Key Phone Digit 1 1 On Star 2 2 Partial Hash 3 3 Exit 4 Sec delay 4 4 Bypass Disable 5 5 Chime Pulse Dialling 6 6 7 Y 8 8 9 9 0 0 Page 17 V2 03 VIEWING TELEPHONE NUMBERS Key Sequence Example shows viewing phone cC number 1 1 Press and 4 1 for phone E number 1 2 Enter the master code You are now in the view mode and the first ep co LP hone digt wil be displayed Use the following table to read the code 3 Press the key to move to the next digit s pad lights 4 Press to end and exit You may wish to check the phone numbers that have been programmed for your security system Zone Light Phone Digit Light Phone Digit Zone 1 1 Fire 9 Zone 2 2 Service 0 Zone 3 3 On Star Zone 4 4 Partial Hash Zone 5 5 Exit 4 Sec Delay Zone 6 6 Bypass Disable Zone 7 7 Chime Pulse Dialling Zone 8 8 Zone 9 9 Zone 10 0 Cancelling Alarm Calls Note Alarm calls will be heard as siren
15. ne two means of escape from each room One will be the normal exit from the building The other may be a window that opens easily An escape ladder may have to be located near the window if there is a long drop to the ground below Set a meeting place outdoors for a headcount of the building occupants Practice escape procedures In a home sleep with bedroom door closed this will increase your escape time If you suspect fire test the door for heat If you think it is safe brace your shoulder against the door and open it cautiously Be ready to slam the door if smoke or heat rush in Practice escaping to the outdoors and meeting in an assigned spot Call the Fire Department from a neighbour s phone NOTE After the installation of your Security System has been completed notify your local Fire and Police Departments to give them your name and address for their records Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms also have other rights which vary from State to State BEDROOM LIVING BEDROOM BEDROOM ROOM ROOM L FIRST FLOOR L SECOND FLOOR JU ULU LI LI FRONT J L T Page 21 V2 03 Page 22 V2 03 WARNING NOTICES This product is to be installed by qualified SERVICE PERSONNEL only The equipment should only be operated with an approved power adapter with insulated live pins CAUTION RISK OF EXPLOSION IF BATTER
16. ny zones are bypassed a sensor in that zone can be violated without affecting the ready light The security system will not arm if the ready light is not on If the power light is off you have no AC power Restore power if possible If not contact your installation company Enter your 4 digit user code to arm the system The armed and exit lights will illuminate You may now leave the building via the designated exit path Note The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire Key Sequence Example shows a User code of 1234 ce being used to set the system to the ON Mode FULLY ARMING THE SYSTEM QUICK ARM MODE Quick Arm is used when the person arming the alarm system does not have a user code is leaving the premises and wants the interior protected To arm in the Quick Arm Mode Close all protected doors and windows Ready light will light when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light The security system will not arm if the ready light is not on If the power light is off you have no AC power Restore power if possible If not contact your installation company The ON key to arm the system The armed and exit lights will illuminate You may now leave the building via the designat
17. the Partial key to partially arm your premises DISARMING FROM THE ON or Partial MODE When you enter the protected area through one of the designated Entry Exit doors the code pad control will sound a solid continuous tone for the duration of the entry delay time or until you enter a valid code After entering a valid code the red armed light will go off and the tone will stop The security system is now DISARMED If a valid code is not entered before the end of the entry delay an alarm will occur NOTE If the red armed light is flashing during the entry delay the alarm system has been activated in your absence Leave the building immediately and call your alarm company and or the police from a safe location Key Sequence Enter your user code to disarm the system from the On or Partial mode Page 8 V2 03 BYPASSING INDIVIDUAL ZONES Bypassing is used to temporarily exclude one or more zones that would normally be protected For instance a pet may need to be left in a part of the house that is usually protected If you wish to bypass one or more zones this must be done while the system is in the disarmed state The following steps are used for bypassing zones Once you have Bypassed the zone s you may Arm the system via the ON or PARTIAL Mode When your security system is disarmed any zones that has been temporarily isolated or bypassed will be reset and will
18. therefore be protected when the system is armed again To manually un bypass zones perform the bypassing procedure on a zone that is already bypassed The corresponding light for that zone will go off when un bypassed Key Sequence This example shows a user bypassing zones 4 and 5 BYPASS 1 Press the BYPASS key The bypass light flashes S Tick box if User code required lt p 2 Enter a 2 digit zone indicating the zone you wish to bypass Example Press the 0 4 keys for zone 4 press 0 5 keys for zone 5 The corresponding light for that zone BYPASS will turn on when bypassed 3 Press the BYPASS key again NB Pleased check with your security installation company to determine if a user code is required to bypass zones If this feature has been enabled you will be required to enter a valid user code after step 1 and before step 2 Page 9 V2 03 GROUP BYPASS By pressing the BYPASS key followed by the 0 0 key then the BYPASS key again all zones that are designated as group bypass zones will be bypassed Now you can arm your system in either the ON or PARTIAL mode Once armed pressing the BYPASS key again will toggle the bypassed zones on and off Key Sequence BYPASS BYPASS 1 Press the BYPASS key The bypass light flashes LJ Tick box if User code required 2 Press 0 0 keys The gro
19. to determine the service condition One or more zone lights will illuminate indicating what service s is required Call your local security installation company immediately for these problems Below is a listing of what each light means in a service condition Key Sequence Q j 1 Enter keys 2 and use the table below to identify the service condition SYSTEM FAULT Press the 1 key The zone light s that is illuminated corresponds to the system fault s below Over Current Fault Expander Low Battery Siren Trouble Expander Box Tamper Expander Trouble Reserved ond a Box Tamper on oO uo 4 Expander Power Note Faults 1 amp 2 are global in nature and will affect all areas of a multi area system Press the key to return to the 1 of 8 service lights ZONE TAMPER Press the 2 key and the zone light s will illuminate showing the zone s that is tampered Press the key to return to the 1 of 8 service lights ZONE LOW BATTERY Press the 3 key The zone light s will illuminate showing which zone s has a low battery This only applies to wireless zones Press the key to return to the 1 of 8 service lights ZONE LOSS OF SUPERVISION Press the 4 key and the zone light s will illuminate showing which zone s has loss of supervision This only applies to wireless zones Press key to return to the 1 of 8 service lights ZONE TRO
20. tone pause siren tone this will repeat several times You can stop the alarm system calling you or any further programmed numbers by pressing the star key for 2 seconds during the pause period of the call This will also end the current call Page 18 V2 03 DELETING TELEPHONE NUMBERS You may need to delete a phone number you have previously chosen For example if you cancelled a mobile phone account Key Sequence Example shows deleting phone number 3 EP Pc n and 4 8 for phone ED 2 Enter the master code 3 Press the Bypass key to delete the saved number BYPASS 4 Press to end and exit COMMUNICATOR BATTERY amp SIREN TEST This test will only be performed if the installer has programmed this option on The test conducts a communicator test once a battery test and siren test The communicator battery and sirens should be tested regularly Contact your security installation company to find out if this test is available Key Sequence 1 Enter keys 4 4 to initiate the test Note Sirens will sound during this test ep e L 3 2 Enter a user code to end the test Page 19 V2 03 SERVICE LIGHT The service light will be lit if the security system requires service If the service light is lit press the key followed by the 2 key
21. up bypass zone lights will turn on when bypassed 3 Press the BYPASS key again NB Pleased check with your security installation company to determine if a user code is required to group bypass If this feature has been enabled you will be required to enter a valid user code after step 1 and before step 2 Page 10 V2 03 CHANGING amp ADDING USER CODES On occasion you may need to change your arm amp disarm codes either as a security measure or for your own convenience User Codes are 4 digits long and must all be different to each other A master Code must be used to Change and Add user codes The default master code is user code one 01 with a code of 1234 Any user code can be assigned as a master code See User Code Authorisation Note the system must be disarmed before user codes can be changed or added Key Sequence P 5 1 Press 5 3 Enter the user code to add or oo ic e g user code 01 4 Enter the new four digit user code 5 Repeat steps 3 and 4 for additional user codes 5 Press when completed 2 Enter an existing master code Page 11 V2 03 DELETING A USER CODE You may be required to delete a user code for example when a member of the household leaves home or the home is purchased from another family Key Sequence 1 Press 5 2 Enter an existing master code 3 Enter the user code
22. xit Your time is now set SET CODE PAD TONES Each code pad can have its sounder tone frequency adjusted to your individual requirements Follow the steps bellow to adjust the code pad sounder Key Sequence 1 Enter 0 to start the code pad O tone adjustment The code pad sounder will sound at the current set frequency 2 Enter the one 1 key to raise the tone or the two 2 key to lower the tone 0000 3 Enter to exit and save the selected code pad tone Page 16 V2 03 PROGRAM PHONE NUMBERS You may have a requirement where in the instance of alarm activation you want the panel to dial a particular phone number E G Your mobile phone There are three 3 numbers that can be viewed entered changed or deleted Only numbers set to pager or siren tone telephone formats can be modified by you One of these formats must have been programmed by the alarm panel installer for you to access this feature Contact your security installation company to ask if the pager or siren tone format was programmed for your use When confirmed use the following Phone number 1 is 4 1 Phone number 2 is 4 2 Phone number 3 is 4 3 To program a new phone number you must do the following Key Sequence Operation Example shows programming phone qe number 2 1 Press and 4 2 for phone number 2
Download Pdf Manuals
Related Search