DWD 102 - Full Compass
Contents
1. Note It is safe to leave the DLT and DLR units in the charger even after the batteries are fully charged The charger will switch to maintain mode to maintain full battery potential Figure 3 Digi Wave Dock Functions DLT 100 2 0 DLR 60 2 0 DLR 60 Yes with NiMH AAA batter Charges Unit ies in DLR only if no batteries with Dock Power Yes internal battery present dock will power DLR ON if battery switch is in NiMH position Charging Status Shown on DLT if unit is OFF Shown on DLR NiMH only Internal Mic Muted when docked Internal Speaker Muted when docked Muted when docked Audio Inputs Outputs Input and Output enabled Output enabled Auto Mode When unit is Chairman Master in 2 way mode or Presenter TALK function in 1 way mode CH 0 TALK n a button is locked ON No effect in other modes Powers DLR ON when power applied to dock powers DLR OFF when power removed from dock battery switch position NiMH Powers DLT ON when power applied to dock powers DLT OFF when power removed from dock Power Up Down Manual Mode TALK function TALK button must be pushed manually Power Up Acts as a charger only Acts as a charger only DLT microphone mixing with dock sources The dock s inputs two mono RCA jacks 10dBV and one XLR jack 4dBu are mixed together in the dock then sent to the DLT 100 2 0 The DLT 100 2 0 then mixes the dock audio with it s microphone befo2. date you purchase your system Your returned warranty card is our way of Knowing when your warranty begins Please take a moment to fill it out and mail the enclosed card You may also register your product online http www williamssound com Warranty registration If you experience difficulty with your system call Toll Free for Customer Assistance 1 800 843 3544 U S A or 1 952 943 2252 Outside the U S A If it is necessary to return the system for service your Customer Service Representative will give you a Return Authorization Number RA and shipping instructions 11 VS WILLIAMS SOUND 10300 Valley View Rd e Eden Prairie MN 55344 800 328 6190 952 943 2252 FAX 952 943 2174 www williamssound com 2014 Williams Sound All Rights Reserved MAN 180C
3. mm x 110 mm x 55 mm LxWxH Shipping Weight 1 4 lbs 0 64 kg Enclosure Black heavy duty plastic molded top with steel base and non skid rubber feet White legends on back DC Power Input 2 5mm ID barrel connector 24VDC input 750mA Center Positive Power Supply Williams Sound TFP 048 Input 100 240VAC 50 60Hz 18W Output 24VDC 750mA Charging Time DLT 100 2 0 5 hours nominal internal LiPo Battery DLR 60 2 0 15 hours nominal based on Williams Sound NiMH battery BAT 022 2 Unit Capacity 2 Units DLT 100 2 0 DLR 60 2 0 or DLR 60 DLT 100 units will charge only no audio Indicators Green LED indicating power at the charger dock Charging status is shown on unit being charged Rear Inputs One set of L R RCAs single ended 10dBV typical per bay One female XLR balanced line level 4dBu typical per bay Rear Outputs Dock Connector Controls One set of L R RCAs single ended 10dBV typical per bay One male XLR balanced line level 4dBu typical per bay One 30 pin connector per bay Supports power charging audio in audio out and control signals One 2 position switch per bay for manual or auto mode Warranty 2 Years Approvals FCC CE RCM Industry Canada RoHS2 CB scheme Energy Star V Charging specifications are based on internal rechargeable LiPo battery not serviceable Specifications subject to change with
4. PRODUCT IS USED WILLIAMS SOUND THEREFORE DISCLAIMS ALL WARRANTIES NOT SET FORTH ABOVE BOTH EXPRESS AND IMPLIED WITH RESPECT TO THE DWD 102 INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WILLIAMS SOUND SHALL NOT BE LIABLE TO ANY PERSON OR ENTITY FOR ANY MEDICAL EXPENSES OR ANY DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY ANY USE DEFECT FAILURE OR MALFUNCTION OF THE PRODUCT WHETHER A CLAIM FOR SUCH DAMAGES IS BASED UPON WARRANTY CONTRACT TORT OR OTHERWISE THE SOLE REMEDY FOR ANY DEFECT FAILURE OR MALFUNCTION OF THE PRODUCT IS REPLACEMENT OF THE PRODUCT NO PERSON HAS ANY AUTHORITY TO BIND WILLIAMS SOUND TO ANY REPRESENTATION OR WARRANTY WITH RESPECT TO THE DWD 102 UNAUTHORIZED REPAIRS OR MODIFICATIONS WILL VOID THE WARRANTY The exclusions and limitations set out above are not intended to and should not be construed so as to contravene mandatory provisions of applicable law If any part or term of this Disclaimer of Warranty is held to be illegal unenforceable or in conflict with applicable law by a court of competent jurisdiction the validity of the remaining portions of this Disclaimer of Warranty shall not be affected and all rights and obligations shall be construed and enforced as if this Limited Warranty did not contain the particular part or term held to be invalid Your warranty becomes effective the
5. YS WILLIAMS SOUND DVVD 102 Digi VVave Jual Bay Jocking Station USER MANUAL Compatible with Digi Wave Models DLT 100 2 0 DLR 60 2 0 and DLR 60 NEZ pi6tW MAN 180C System Overview Thank you for purchasing the DWD 102 Digi Wave Dual Bay Docking Station The Digi Wave Dock when used with second generation Digi Wave 2 0 products can be used to receive audio through a Digi Wave receiver or transceiver and send the audio into a sound system or send audio from a sound system to a transceiver for broadcast There are many applications for the dock for more information please visit our website and download the Digi Wave Dock Applications Guide The Digi Wave Dock supports audio input output functions with the DLT 100 2 0 DLR 60 2 0 and DLR 60 models It will only act as a charger for the DLT 100 System Includes 1 DWD 102 Digi Wave Dual Bay Docking Station 1 TFP 048 Power Supply 1 WLC 004 Line Cord U S 2 WCA 078 Stereo RCA Cables 4 4 4 RBP 005 Support Pads 1 8 thick 4 RBP 006 Support Pads 1 16 thin Recycling Instructions Help Williams Sound protect the environment Please take the time to dispose of your equipment properly Product Recycling for Customers in the European Union AV Please do NOT dispose of your Williams Sound equipment in the vA household trash Please take the equipment to an electron
6. ics cy recycling center OR return the product to the factory for proper disposal Battery Recycling for Customers in the European Union lt lt Please do NOT dispose of used batteries in the household trash Please take the batteries to a retail or community collection point E for recycling 2 Connectors and Controls Figure 1 Rear View Bay 2 Bay 1 10V RMS Max 10V RMS Max WA williamssound com DWD 102 24VDC 9 9 aw 7 eo Co y Oleg 7 Co 6 6 OIE 6 l Line In J l Line Out J Man Man Line In J l Line Out J 7 XLR RCA XLR RCA Auto Auto XLR RCA XLR RCA Line Line Line Line Manual Manual Line Line Line Line Input Inputs Output Outputs Switch Switch Input Inputs Output Outputs Bay 2 Bay 2 Bay 2 Bay2 Bay2 Bay1 Bay1 Bay 1 Bay 1 Bay 1 Power Supply Connector Figure 2 Top View Bay 1 Power Indicator LED Bay 2 DIGI WAVE DOCK Setup Instructions 1 Connect the external devices to the XLR or RCA jacks on the back of the Digi Wave Dock Figure 1 Both RCA and the single XLR input jacks are all mixed internally but for proper mixing to occur at the output without any adjustments the following combinations can be used One single RCA jack by itself both RCA jacks the XLR jack by itself or both RCA jacks and the XLR jack If one RCA jack is to be mixed with the XLR jack the gain
7. n DLT microphone mixing with dock sources 3 If the transmitted audio is distorting turn the DLT line level down see section on DLT microphone mixing with dock sources or turn the audio level down at the source DLT DLR not charging or indicating charge 1 Make sure the DLT or DLR are seated firmly on the dock s 30 pin connector s 2 Check that the line cord is firmly plugged into the power supply the power supply is plugged into the AC outlet and the power supply connector is plugged in on the back of the Digi Wave Dock inserted firmly until it stops 8 Verify the dock s green power LED is ON Note DLTs do not indicate charge status when powered ON but DLRs do 4 On DLR verify the NiMH batteries are installed correctly not reversed and battery switch is set to NiMH position 10 2 Year Warranty Williams Sound products are engineered designed and manufactured under carefully controlled conditions to provide you with many years of reliable service Williams Sound warrants the DWD 102 Digi Wave Dual Bay Docking Station against defects in materials and workmanship for TWO 2 years During the first 2 years from the purchase date we will promptly repair or replace the DWD 102 Microphones earphones headphones rechargeable batteries cables carry cases and most other accessory products carry a 90 day warranty WILLIAMS SOUND HAS NO CONTROL OVER THE CONDITIONS UNDER WHICH THIS
8. of the RCA source will need to be adjusted at the source Select DLT mode We recommend using Chairman Master mode for two reasons 1 The Chairman Master has 1 Talk Priority so the Talk button on this unit can never be bumped off by another user and 2 The Chairman Master will be powered by the dock and all other units synchronize to the Chairman Master making it a more reliable Master than one powered from the internal battery Insert any combination of DLT 100 2 0 transceiver s or DLR 60 2 0 receiver s into the bays Figure 2 The unit s must be facing forward for proper mating to the 30 pin connector Using the appropriate line cord US EURO UK or AUS into the TFP 048 plug the TFP 048 power supply into the AC wall outlet Plug the power connector into the rear of the DWD 102 unit figure 1 The green LED power indicator should light up Figure 2 Select either Auto or Manual for each docked device using the switch es on the back See Figure 3 for an explanation of the difference between the two modes You may charge any combination of DLT 100 2 0 DLT 100 DLR 60 2 0 or DLR 60s In DLR 60 2 0 and DLR 60 units NiMH batteries must be used and the battery switch must be in the NiMH position Digi Wave Dock audio inputs outputs are only available on the DLT 100 2 0 DLR 60 2 0 and DLR 60 DLT 100s can be docked but will charge only no audio See Digi Wave Dock Functions chart Figure 3
9. out notice New batteries have various charge conditions Some DLT DLR s may take less or more time to fully charge Charging batteries generates heat The receivers transceivers charger and power supply may feel warm when charging Do not charge units in a closed enclosure such as a carry case or brief case Troubleshooting No audio transmitted from docked DLT 100 2 0 1 Make sure the DLT is seated firmly on the dock s 30 pin connector 2 Make sure the dock and DLT are powered ON 8 Check the source input into the dock make sure it is connected powered on and playing producing audio 4 Verify that the incoming audio level is sufficient 5 Make sure the TALK button red ring light is ON on the DLT 6 Make sure the DLT is set up as a Chairman Master recommended Other modes can be used but talk priority may cause the docked DLT to go off air when another unit enables the TALK function 7 Make sure the DLT and DLR s are on the same Group 8 Verify the DLT is transmitting audio Take it out of the dock talk into the on board microphone listen with a DLR receiver and make sure it is receiving audio When this is verified put the DLT back in the dock 9 Verify the DLT 30 pin attenuator setting is not O as this mutes the dock input No audio received by docked DLT 100 2 0 or DLR 60 2 0 1 Make sure the DLT or DLR is seated firmly on the dock s 30 pin connector 2 Make sure the dock and DLT or DLR are po
10. re transmitting Depending upon what sources are being mixed there may be a level mismatch between the dock and the DLT s microphone level The DLT 100 2 0 includes line level adjustment for proper mixing To adjust the DLT 100 2 0 line level gain hold the button for 3 seconds The default level is L 5 or OdB of gain adjustment See Figure 4 below for level settings and corresponding gain attenuation Figure 4 DLT Setting Digi Wave Dock Functions Level Setting on i 2 3 4 5 ri DLT Line level Gain Mute 120B 9aB 6aB 3aB oaB 30 Attenuation dB Note The microphone volume adjustment can also be used but may require other DLTs microphone levels to be adjusted too which makes it a more cumbersome method and therefore line level adjustment is recommended Installing the Support Pads Two sets of supporting pads have been supplied with the dock to support the back of the unit s when sitting in the dock thick 1 8 and thin 1 16 Use the table below to choose which pad thickness to use Figure 5 See the diagram below showing where to affix the pads Figure 6 Figure 5 Support Pad Required DLT 100 DLT 100 DLR 60 DLR 60 with skin with skin Thick pad Thin pad Thin pad 1 8 1 16 1 16 Figure 6 Support Pad Installation DWD 102 Specifications Dimensions 8 88 x 4 34 x 2 16 226
11. wered ON 8 Make sure the sending and receiving transceiver receiver are both on the same Group 4 Make sure the TALK button red ring light is ON on the DLT that is serving as the transmitter 5 Make sure the receiving DLT DLR is receiving audio Take it out of the dock listen to the on board speaker and make sure it is receiving audio When this is verified put it back in the dock 6 Check the dock output for the bay by connecting the RCA or XLR outputs to a device that will show or produce audio such as a boombox or small mixer with VU meters 7 Make sure the device receiving audio from the dock is connected powered on and if applicable on the correct bay output for the dock the two bays are not connected 8 The audio output level is different for the RCA and XLR jacks Make sure the correct output is being used for the connected equipment One or more source audio levels too quiet or too loud not mixing evenly 1 If the RCA inputs are being used with an XLR source both RCA inputs must be used to mix evenly with the XLR source If using amono RCA source it must be wyed out using a Y cable or adapter and sent into both RCA inputs If just one RCA is used when mixed with the XLR it will not mix evenly and will be quieter than the XLR source 2 If the DLT microphone level is not mixing evenly with the XLR and or RCA sources adjust the DLT line input level to match the microphone audio level see section o
Download Pdf Manuals
Related Search