MEITRACK T1 User Guide
Contents
1. Ground wire 6 GND Black It can be used as a ground wire connected to an analog sensor Digital input 3 positive trigger 7 Input 3 White Connect to the vehicle ACC cable by default to detect the vehicle ACC status Analog input 1 with 12 bit resolution and valid voltage 0 6 6 V 8 AD Input 1 Connect to an external sensor such as the fuel sensor 2 E D Analog input 2 with 12 bit resolution and valid voltage 0 6 6 V 9 Fuel sensor input The AD cable is equipped with a white plug It is connected to the A53 fuel sensor by default Output 1 Valid low level 0 V Invalid open collector 10 Output 1 Yellow Maximum voltage for output open collector invalid 40 V Maximum current for output low voltage valid 400 mA Connect to an external relay to remotely cut off the vehicle fuel cable or engine power supply Output 2 Valid low level 0 V Invalid open collector Yellow 11 Output 2 Maximum voltage for output open collector invalid 40 V Maximum current for output low voltage valid 400 mA Connect to an external relay to remotely cut off the vehicle fuel cable or engine power supply TTL3 3V level 12 Digital temperature Connect to the A52 digital temperature sensor or iButton by default by using sensor or iButton input Yellow the A61 sensor box port Note The DC or AC voltage that is greater than 3 3 V is not allowed Otherwise the device may be damaged 8 22. a Wiegand port Note The RS232 port can be used with either the handset or the camera at a time 8 5 Installing the Camera RS232 Port Power output Output voltage 5 V RX T1 receives data from the camera TX T1 sends data to the camera To connect T1 to a camera an 8 pin to 4 pin conversion cable is required 8 pins are connected to T1 and 4 pins are connected to the camera Connect 8 pins to the device Connect 4 pins to the camera FTP er O PRR EE Bege is eeeecec essrrr pereeroeEet e t o ooo tee eo o so Copyright O 2015 Meitrack Group All rights reserved 16 Q meitrack MEITRACK T1 User Guide Note The RS232 port can be used with either the handset or the RFID reader at a time 8 6 Mounting the T1 Tighten the four screws shown in the following figure If you have any questions do not hesitate to email us at info meitrack com Copyright 2015 Meitrack Group All rights reserved 17
3. 8 1 Installing GPS and GSM Antennas GSM antenna GPS antenna Connect the GSM antenna to the connector which is labeled GSM The GSM antenna is non directional so you can hide it in any place of a vehicle Connect the GPS antenna to the connector which is labeled GPS It is recommended that the antenna is facing up to the sky and the antenna side with words is downwards Secure the antenna by using double sided tapes Note Do not install the GPS antenna at a place with metal 8 2 Installing an 1 0 Cable The 1 0 cable is a 12 pin cable including the power analog input digital temperature sensor input and negative positive input and output DC SOSIIN2IINSIAD2i0ut2 3 5 7 6 EM ensroenreseno Positive charge of the power input connected to the positive charge of the 1 Power vehicle storage battery Input voltage 11 V to 36 V 12 V is recommended Copyright 2015 Meitrack Group All rights reserved 12 GC meitrack MEITRACK T1 User Guide Ground wire connected to the negative charge of the vehicle storage battery or 2 GND Black to the negative terminal White Digital input 1 negative trigger SOS button by default Black Ground wire connected to input 1 SOS button Digital input 2 negative trigger 3 Input 1 4 GND 5 Input 2 White Connect to a door trigger signal cable to detect vehicle door status Most Chinese Korean and Japanese cars are negative edge triggered
4. 1 Power Cable Ground Wire Pin 1 2 Connect the power cable red and ground wire black to the positive and negative charges of the vehicle battery respectively Copyright 2015 Meitrack Group All rights reserved 13 Q meitrack MEITRACK T1 User Guide Car Battery 8 2 2 ACC and Door Detection Pin 5 7 INPUT3 Device ACC Detection 12V INPUT 2 Door lamp Door signal is negative trigger Connection of negative trigger door Note If input 3 is connected to the ACC position after the engine is started the platform will read it as ON OFF ON If input 3 is connected to the Start position after the engine is started the platform will read it as OFF ON OFF If installed correctly after the engine is started the platform will read it as OFF ON 8 2 3 Output Control Pin 10 11 Fuel pump power line ee Yellow outputl Fuel pump Note To implement remote fuel and power cut off connect the relay to the fuel pump cable or the engine cable in series Copyright 2015 Meitrack Group All rights reserved 14 Q meitrack MEITRACK T1 User Guide 8 2 4 Sensor Input For pin 8 analog input 1 a sensor whose output voltage ranges from O V to 6 6 V can be installed The analog voltage calculation formula is as follows Voltage AD x 3 3 x 2 4096 Pin 10 is connected to the A53 fuel sensor by default You can install the sensor without calculation formula added on the platfor
5. Be IO WMO O e RN DSR rset RR NE A A DRE RS SRD DN ER DE EE ND RS RD RR AR et 15 8 3 Installing the Handset R5232 PONE ae ee NEE E EENET EEEE EENE PA US GE era ete cc 15 8 4 Installing the REID Reader RS232 Port ni 16 8 5 Installinsthe Camera RS2 32 POM nes een oies den des a Em este cales sec tete 16 8 6 Mounting the T1 iii rena ana r e eae anne aaa anne era a nara rea nara cana acre renan cre rea nasc erea ans rer aaa as cereanaa 17 Copyright 2015 Meitrack Group All rights reserved 3 2 meitrack MEITRACK T1 User Guide 1 Copyright and Disclaimer Copyright 2015 MEITRACK All rights reserved EU and are trademarks that belong to Meitrack Group The user manual may be changed without notice Without prior written consent of Meitrack Group this user manual or any part thereof may not be reproduced for any purpose whatsoever or transmitted in any form either electronically or mechanically including photocopying and recording Meitrack Group shall not be liable for direct indirect special incidental or consequential damages including but not limited to economic losses personal injuries and loss of assets and property caused by the use inability or illegality to use the product or documentation 2 Product Overview The T1 is a brand new high end vehicle GPS tracker with market proven quality and precise positioning In addition to real time tracking it supports various pe
6. Q meitrack MEITRACK T1 User Guide MEITRACK T1 User Guide Q meitrack MEITRACK T1 User Guide Change History Creation Date 2014 06 10 Project T1 Update Date 2015 09 30 Copyright 2015 Meitrack Group All rights reserved 2 2 meitrack MEITRACK T1 User Guide Contents TOY HIS and INS CVE wenn sare siemens a een ee re 4 2 Product OVER ICN aca A EENCER HERDER EREERESNEERERRER 4 3 Product Function and SpeciicatOns nssecezccaceasssaasetomseasnsonecatinasnsoannenssanswbandeasieurcoateastisneapenssnnbedasdanueursentnasiverneensveniedsidenmeustaaneneasounes 4 2 PROQUCE FO Ur assisto ee ee tft di E E 4 3 LL POS AOU Dach ee ae en een een en Sense are 4 31 2 200 A ee A RR ere ene 4 3 1 Other FONCIONS SR ER een da du OD te SRD cre do eue ed en dead 4 3 1 4 Functions OF Optional Accessories nennen een 5 32 SPEISEN ONS ee er AA AT E E AA ETE E E A O EA A E 5 ATT aNd ACCO SONES eari nE EEEE E S O EEE EEA EE EEO ND E EE EO 6 ADDEN ee ee E ol tne O ecto ee OEE E AE E O E RR A A 7 BIS N ay A A OEA A A A ee A E A A sua RD 7 6 LIN Aline the NCA a a a a ee ee ne 7 6 2 CNN E A ae EE DE den ae ee dd D ane een E 8 DS LED WC O ec nn D en nce eset ee need 8 SA Confedrea Dy Computer na een ide 8 Eos Pie IE DU MOD PHONG PR a SET ad Seo SE ad ee Eee 9 6 6 Common SMS COMMANdS xiccuzeestecsdedenatacsdueasarectecessedausesusanenenvedcesescosdenssssenessteneqeesoyedoueesnaaioresbesntecceosess
7. ance by RFID report LED display Display advertisements and announcements Used for real time vehicle scheduling and A21 LCD display Used for two way calling SMS sending and receiving Handset and remote monitoring Camera Used with a Micro SD card Take photos 1 RS232 port management 3 2 Specifications Working hour 200 hours in power saving mode and 10 hours in normal mode Green indicator showing the GSM signal LED indicator Blue indicator showing the GPS signal 1 SOS button for sending SMSs or dialing Button Switch 1 power button Copyright 2015 Meitrack Group All rights reserved 5 MEITRACKT1UserGuide ee O OO Guide CG meitrack me fi DT 3 digital inputs 2 negative inputs and 1 positive input 2 analog detection inputs 2 outputs I O port 1 RS232 port 1 USB port 1 digital temperature sensor port 4 T1 and Accessories T1 and standard accessories T1 with a built in battery GPSantenna GSM antenna 1 0 cable SOS button USB cable CD Optional accessories Camera Handset RFID reader A21 LCD display dialing and SMS display A53 fuel sensor AS A52 digital temperature sensor LED display iButton A61 sensor box Copyright 2015 Meitrack Group All rights reserved 6 mean uen SG meitcck 5 Appearance Power button GSM indicator GPS indicator GSM antenna connector GPS antenna connector USB Handse RFID USB port Handset RFID reader P
8. arger the value is the stronger the Indicates the GSM signal strength signal is If the value is greater than 12 GPRS reaches the normal level Indicates the speed Unit km h http maps meigps co This is a map link m lat 22 513781 amp Ing Latitude 22 513781 None 114 057183 Longitude 114 057183 Copyright 2015 Meitrack Group All rights reserved 9 Q meitrack MEITRACK T1 User Guide Google maps _ 22 540103 114 082329 EN sis Get directions My places Ze ER Shenf N Zhor in py e J w j Bldg gy RNP ES E RE 7 henhua Rd emitt o F i Huagia 5 Satellite Guangdong Shenzhen Fu Tian Qu Shen Nan Zhong Lu 30135 China Mode ibe F as Traffic Shenzne ah L o ye Fortune ta y epa Ma t zo E IRS Tr Market E TETEN Work zum Ri Sam ig de Plaza he 2 m p E 7 ports Ce Shenzhe ia HEREA i Middle School a gricultura mis Nanyuan Rd Trade Bide SR dany Er n RARE Fuhua Rd Mb a Hotei Jinghai 8 FF A Fubua Branch Garde 5 Lotu vic ir RME E t E ne Bldg hay B Rifuge a LA i Boki ot ammes ami a Qingtuyua Fujing Rd ama 7 A ee 1 N Park Big R 75 ons 200 m s 2611 Gables nai catp 629 Winding Mapabc Tene ST USE Tan 4 6 6 Common SMS Commands 6 6 1 Setting a Combined Function Phone Number A71 SMS sending 0000 A71 Phone number 1 Phone number 2 Phone number 3 SMS reply IMEI A71 OK Descr
9. evsexessameesotesbecweeases 10 6 6 1 Setting a Combined Function Phone Number A71 sessssnessssnnssseressserrsssreressrrressrrressrrressrrresserrrssrrerssereesseeeeeseeee 10 6 6 2 Setting a Listen in Phone Number A72 eeesssesssesnnsnsneonnenennonnnnnnennnennnnnnnsnnnnonnsnennonnsnsnnnnnsnsnnsnnsnsnnesnensnssnssssnnennenn 10 6 6 3 Setting the Smart Sleep Mode A73 cccccsssseccccessececceeseccecuusecccsauseccesaeeceesueuecceseeeceesaeueceesseueceesauaeeeeseaaeeeessaanees 11 6 6 4 Selecting a Serial Port and Peripheral C70 ccccccccssseccccsesececceeseccecaeseceeseeneceeseeeeceeseeueceeseeaeceesauaeceeseuaeeessuagsees 11 PNO EKNE Velen E E EE E NENE E A EE E 11 SAS a a E E ee ee ee O E ae 12 8 L Installing GPS and GSM ANTENNAS sasiarasoaacavarvasswtennassavebswssahdewsasanibsusguteaneasatentosausdsanasatebsvasstdensacataesoasonascsasalantoaaetdcneasancsbiass 12 8 2 Installing an I O Cable 12 8 2 1 Power Cable Ground Wire Pin 1 2 sssssssssssssssssssssssssssssssssssssssssssssessesessessessssseseseseeseeeeeeseeeseesesesseeeeeeeegeas 13 8 2 2 ACC and Door Detection PIA 5 7 swsissssosssssccsnnnssvonsionacdvnnoesesvnsosndbennnsdesonsionacdoanostevonsiossdbennnnsesonbiowasdoasnesesbnsiavadevannwaiine 14 8 2 3 Output Control Pin 10 11 n csccsncsscccancesesnnnssnconensoassennssnosennsedieennntsnasenesndebennsstossdesndbssnassndsenesndetenosstocedecndeccxoestceasnt 14
10. ipheral selection 1 The device peripheral connects the handset Peripheral selection 2 The device peripheral connects the LED display Peripheral selection 3 The device peripheral connects the A21 LCD display Peripheral selection 4 The device peripheral connects the RFID reader Example 0000 C70 2 4 Reply 353358017784062 C70 0K For details about SMS commands see the MEITRACK SMS Protocol Note 1 The default SMS command password is 0000 You can change the password by using Meitrack Manager and SMS commands 2 The device can be configured by SMS commands with a correct password After an authorized phone number is set only the authorized phone number can receive the preset SMS event report 7 MS03 Tracking System Visit http ms03 trackingmate com enter the user name and password and log in to the MSO3 Purchase the login account from your provider For more information about how to add a tracker see the MEITRACK GPS Tracking System MSO3 User Guide chapter 4 Getting Started The MS03 supports the following functions eee Copyright 2015 Meitrack Group All rights reserved 11 Q meitrack MEITRACK T1 User Guide Track by time interval or distance Query historical traces Set polygon geo fences Bind driver and vehicle information View various reports Send commands in batches Support OTA updates For details see the MEITRACK GPS Tracking System MSO3 User Guide 8 Installing the T1
11. iption Phone number A phone number has a maximum of 16 bytes If no phone numbers are set leave them blank Phone numbers are empty by default Phone number 1 2 3 SOS phone numbers When you call the tracker by using these phone numbers the tracker will reply an SMS with the location and send geo fence alarms and low power alarms If all combined function phone numbers need to be deleted send 0000 A71 When the SOS button is pressed the tracker dials phone numbers 1 2 and 3 in sequence The tracker stops dialing when a phone number responds Example 0000 A71 13811111111 13822222222 13833333333 Reply 353358017784062 A71 0K 6 6 2 Setting a Listen in Phone Number A72 SMS sending 0000 A72 Listen in phone number 1 Listen in phone number 2 SMS reply IMEI A72 0K Description When you call the tracker by using the authorized listen in phone number the tracker will answer the call automatically and enter the listen in state In this way the tracker will not make any sound A maximum of two phone numbers can be set Each phone number has a maximum of 16 digits If no phone numbers are set leave them blank Phone numbers are empty by default If no phone numbers are set and commas are remained phone numbers set before will be deleted If all phone numbers need to be deleted send 0000 A72 Example 0000 A72 13844444444 13855555555 Reply 353358017784062 A72 0K Copyright 2015 Meitrack Group All rights reserved 10 2
12. m For details see the A53 Fuel Sensor User Guide Pin 12 is connected to A61 A52 temperature sensor or iButton by default For details see the Meitrack Temperature Sensor User Guide and Meitrack iButton User Guide Note The white plug on the T1 harness consists of the power cable red ground wire black AD2 cable blue and SEN cable blue The T1 can connect to a maximum of two A61 sensor boxes You can install a maximum of eight A52 temperature sensor ports For details see the MEITRACK Temperature Sensor User Guide 8 3 Installing the Handset RS232 Port 14 34547 2 46 8 DC ISOSJINZ IN3 AD MA USB Handset RFID GNDIGNDIGNDIAD 1 OutilsENI Power output Output voltage 5 V RX T1 receives data from the handset TX T1 sends data to the handset Negative charge of the microphone Positive charge of the loudspeaker Negative charge of the loudspeaker Note The RS232 port can be used with either the RFID reader or the camera at a time 1 US Blue Positive charge of the microphone Copyright 2015 Meitrack Group All rights reserved 15 Q meitrack MEITRACK T1 User Guide 8 4 Installing the RFID Reader RS232 Port t 8 5 7 2 4 648 USB Handset RFID Power output Output voltage 5 V RX T1 receives data from the RFID reader Reserved TX T1 sends data to the RFID reader Remarks The T1 RFID reader is not compatible with the MVT600 RFID reader In the MVT600 the RS232 port is
13. meitrack MEITRACK T1 User Guide 6 6 3 Setting the Smart Sleep Mode A73 SMS sending 0000 A73 Sleep level SMS reply IMEI A73 OK Description When the sleep level is 0 the sleep mode is disabled When the sleep level is 1 the tracker enters the normal sleep mode The GSM module always works and the GPS module occasionally enters the sleep mode The tracker works 25 longer in the normal sleep mode than that in the normal working mode This mode is not recommended for short interval tracking this will affect the route precision When the sleep level is 2 the tracker enters deep sleep mode If no event SOS button changes incoming calls SMSs or vibration is triggered after five minutes the GPS module will stop and the GSM module will enter sleep mode Once an event is triggered the GPS and GSM modules will be woken up Note In any condition you can use an SMS command to disable the sleep mode and then the tracker exits the sleep mode and returns back to the normal working mode Example 0000 A73 2 Reply 353358017784062 A73 0K 6 6 4 Selecting a Serial Port and Peripheral C70 SMS sending 0000 C70 Serial port selection Peripheral selection Reply IMEI C70 0K Description Serial port selection 1 The peripheral port of the device is debug port Serial port selection 2 The peripheral port of the device is UART port default Peripheral selection 0 The device peripheral connects the camera default Per
14. nnect the T1 to a PC by using the USB to serial cable 3 Run Meitrack Manager then the following dialog box will appear m Meitrack Manager Waiting forconnecting Turn on the device then Meitrack Manager will detect the device model automatically and the parameter page will appear Copyright 2015 Meitrack Group All rights reserved 8 GC meitrack MEITRACK T1 User Guide accordingly For details about Meitrack Manager see the MEITRACK Manager User Guide 6 5 Tracking by Mobile Phone Call or send the 0000 A00 command by SMS to the T1 SIM card number The device will reply an SMS with a map link Click the SMS link The location will be displayed on Google Maps on your mobile phone Note Ensure that the T1 SIM card number has subscribed the caller ID service Otherwise the caller ID will be blocked PERA 3G g 1 8K s Aul 10 48 TEKK 3G a 1 9K s A Ful 10 53 M_Tracker 445 15 ATI M_Tracker7445 1 15815567445 F RRI Now 061314 10 36 V 26 0Km h 96 http Saito 2lat 22 5137818Ing 114 0571 ri var 83 it she f SMS example Now 061314 10 36 V 26 0Km h 96 http maps meigps com lat 22 513781 amp Ing 114 057183 Indicates the current location SMS header indicates the alarm type Indicates the date and time in 061314 10 36 None MMDDYY hh mm format A Valid V Invalid The following table describes the SMS format The GPS is invalid Value 1 32 The l
15. ower Input Output port port 6 First Use 6 1 Installing the SIM Card To install the SIM card perform the following operations 1 Loosen the screw and remove the front cover of the T1 2 Insert the SIM card into the card slot with its gold plated contacts facing towards the Printed Circuit Board PCB 3 Close the cover and tighten the screw Note O Ensure that the SIM card has sufficient balance Ensure that the phone card PIN lock has been closed properly Ensure that the SIM card in the T1 has subscribed the caller ID service if you want to use your authorized phone number to call the T1 Power off the T1 before installing the SIM card Copyright 2015 Meitrack Group All rights reserved 7 Q meitrack MEITRACK T1 User Guide 6 2 Charging When you use the T1 for the first time connect the T1 GND Black and Power Red wires to 12 V or 24 V external power supply for charging Ensure that the T1 is charged at least three hours Eight hours are recommended The T1 can be installed on a vehicle only after it is configured and tested 6 3 LED Indicator Press and hold down the power button for 3 seconds to 5 seconds to start the T1 Blink 0 1s on and 2 9s off Blink 0 1s on and 2 9s off 6 4 Configured by Computer This section describes how to use Meitrack Manager to configure the T1 on a computer Procedure 1 Install the USB to serial cable driver and Meitrack Manager 2 Co
16. ripherals and can be installed into taxies freight cars and buses 3 Product Function and Specifications 3 1 Product Function 3 1 1 Position Tracking GPS GSM dual module tracking Real time location query Track by time interval Track by distance Direction change report Speeding alarm Track by mobile phone 3 1 2 Anti Theft SOS alarm GPS antenna cut off alarm External power supply cut off alarm GPS blind spot alarm Remote vehicle fuel power cut off alarm Engine or vehicle door status alarm Towing alarm Polygon geo fence alarm Fuel monitoring 3 1 3 Other Functions SMS GPRS TCP UDP communication Meitrack protocol Copyright 2015 Meitrack Group All rights reserved 4 MEITRACK T1 User Guide G mel track Built in 8 MB buffer for recording driving routes storing 8 192 GPRS cache 256 SMS cache and 131 072 GPS logs Mileage report Low power alarm Build in vibration sensor and acceleration sensor Support Over the Air OTA SIM card balance query Halt to Start and Start to Halt alarms Online Parameter Editor 3 1 4 Functions of Optional Accessories Identify the driver ID and grant permission to start iButton the vehicle A53 resistor voltage output mode fuel sensor Check fuel A52 digital temperature sensor A61 sensor box Check temperature Super magnet Fix the device in place Identify the driver ID and grant permission to start RFID reader the vehicle Monitor driver attend
Download Pdf Manuals
Related Search