1. Package Contents 2. Installation Precautions 3. Physical
Contents
1. PLANET 2 Installation Precautions Networking amp Communication 1 Users MUST use a proper and well installed surge arrestor and grounding wired with the WNAP 7325 otherwise a sudden lightning could cause fatal damage to the WNAP 7325 EMD Lightning DAMAGE IS NOT COVERED UNDER 300Mbps 802 11a n Wireless Outdoor CPE WARRANTY 2 Users MUST use the Power cord and PoE Injector shipped in the box with the WNAP 7325 Use of other options will cause damage to the WNAP 7325 Quick Installation Guide 1 Package Contents Thank you for choosing PLANET WNAP 7325 Before installing the AP please verify the contents inside the package box 3 Physical Introduction WNAP 7325 Quick Guide Rear Panel Description LED Indication Power LED LAN 1 LED PoE Injector amp Power Cord Plastic Strap x 1 ee If there is any item missing or damaged please contact the seller immediately LAN 2 LED Signal Indicator Bottom Panel Description Port B Plug the RJ45 Ethernet cable into the PoE LAN Port of the WNAP 7325 Then slide back the cover of the WNAP 7325 Grounding Terminal to finish the installation Reset Button STEP 2 Plug the power cord into the DC port and the other LAN2 PoE LAN side into the AC socket Then plug the RJ45 cable as shown in picture 4 under Step 1 into the POE port of the PoE injector Ethernet Cable 4 Hardware Installation o f Data PC STEP 1 A Push the latch on t2. F Password Remember my credentials For security reasons it is recommended to change the password at the first login and memorize it 6 Web Login Connect the WNAP 7325 with your PC by an Ethernet cable plugging in LAN port of PoE injector in one side and in LAN port of PC in the other side Power on the WNAP 7325 by PoE from PoE injector Click Start button located in the lower left corner of your computer Click Control Panel Double click Network and Sharing Center icon Click Change Adapter Settings Double click Local Area Connection Select Internet Protocol Version 4 TCP IPv4 and click Properties Select Use the following IP address and then click OK button twice to save the configuration For example as the default IP address of the WNAP 7325_ is 192 168 1 253 and the router is 192 168 1 254 then you may choose from 192 168 1 1 to 192 168 1 252 Networking Sharing General lk Connect using You can get IP setti j automatically if your network supports this capability Other need sk ork admi z is lity wise to ask your network administrator EY Broadcom NetLink TM Gigabit Ethemet for the appropria sel 3 Obtain on aes ama Use the following IP address This connection uses the following items o Client for Microsoft Networks E QoS Packet Scheduler dE File and Printer
3. 90 amp type 3 If you have further questions please contact the local dealer or distributor where you purchased this product 2011 E10580 000 a
4. Sharing for Microsoft Networks Subnet mask 255 255 255 0 Intemet Protocol Version 6 TCP IPv6 Intemet Protocol Version 4 TCP IPv4 4 Link Layer Topology Discovery Mapper I O Driver 4 Link Layer Topology Discovery Responder Obtain DNS server address automatically Use the following DNS server addresses IP address 192 168 1 100 Default gateway 192 168 1 254 Install Uninstall Properties Preferred DNS server Description Alternate DNS server Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication x 2 across diverse interconnected networks E Validate settings upon exit STEP 3 After you enter into the Web User Interface go to Wireless Basic Settings to configure your wireless network WNAP 7325 300Mbps 802 11a n Wireless Outdoor CPE Basic Settings Band 5G 11NA HT40 m Channel 149 5745MHz M Data Rate Auto M Mode Access Point kA SSID WNAP 7325 Suppress SSID Disable x Country code usa Change MAC Address Disable m Transmission Distance on Further Information The above steps introduce the simple installations and configurations of the WNAP 7325 For further configurations of different operation modes please refer to the user manual which you can download from the website http www planet com tw en support download php typel 4 amp model 485
5. he bottom of the WNAP 7325 to remove the sliding cover 24V PoE Injector PoE Port Ethernet Cable Data Power 5 Pole Mounting STEP 1 Place the strap through the slot on the back of the WNAP 7325 and then around the pole Tighten the strap to secure the WNAP 7325 IMPORTANT SAFETY PRECAUTIONS 1 LIVES MAY BE AT RISK Please be aware for the electric wires around and tighten the pole Carefully read the section OUTDOOR INSTALLATION WARNING in the manual before installation Users MUST use the Power cord and PoE Injector shipped in the box with the WNAP 7325 Otherwise the product might be damaged Default IP Address 192 168 1 253 Default Username admin Default Password admin Default SSID WNAP 7325 STEP 1 The Web management allows you to access and manage the wireless AP easily Launch the Web browser and enter the default IP address http 192 168 1 253 eE s3 Ee Ae C 1921681253 192 168 1 253 x lt gt 52 168 1 253 File Edit View Favorites Tools Help STEP 2 When the login window pops up please enter the User Name and Password The default User Name and Password are both admin Then click OK button to continue The server 192 168 1 253 is asking for your user name and password The server requires a username and password Warning Your user name and password will be sent using basic authentication on a connection that isn t secure aa User name
Download Pdf Manuals
Related Search