Product Manual
Contents
1. 5 GPL feature set is supported 6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported 7 WRITE DMA QUEUED FUA EXT command is supported 8 64 bit World Wide Name is supported 9 10 Obsolete 11 12 Reserved for TLC 13 IDLE IMMEDIATE command with IUNLOAD feature is supported 14 Shall be set to 1 15 Shall be cleared to 0 Bit Word 88 0 Ultra DMA mode 0 is supported 1 Ultra DMA mode 1 is supported 2 Ultra DMA mode 2 is supported 3 Ultra DMA mode 3 is supported 4 Ultra DMA mode 4 is supported 5 Ultra DMA mode 5 is supported 6 Ultra DMA mode 6 is supported 8 Ultra DMA mode 0 is currently active 9 Ultra DMA mode 1 is currently active 10 Ultra DMA mode 2 is currently active 11 Ultra DMA mode 3 is currently active 12 Ultra DMA mode 4 is currently active 13 Ultra DMA mode 5 is currently active 14 Ultra DMA mode 6 is currently active Seagate SV35 Series HDD Product Manual Rev E 24 www seagate com 4 3 2 This command controls the implementation of various features that the drive supports When the drive receives this command it sets BSY checks the contents of the Features register clears BSY and generates an interrupt If the value in the register does not represent a feature that the drive supports the command is aborted Power on default has the read look ahead and write caching features enabled The acceptable values for the Features Set Features command regi2. 20 C per hour max operating 30 C per hour max non operating 20 C per hour max operating 30 C per hour max non operating Relative humidity 5 to 95 operating 5 to 95 non operating 5 to 95 operating 5 to 95 non operating 5 to 95 operating 5 to 95 non operating Relative humidity gradient max 30 per hour 30 per hour 30 per hour Wet bulb temperature max 37 7 C max operating 40 0 C max non operating 37 7 C operating 40 0 C non operating 37 7 C max operating 40 0 C max non operating Altitude operating 304 8m to 3048m 71000 ft to 10 000 ft 304 8m to 3048m 71000 ft to 10 000 ft 304 8m to 3048m 71000 ft to 10 000 ft Seagate SV35 Series HDD Product Manual Rev E www seagate com Table 1 Drive specifications summary for 3TB 2TB and 1TB models Continued Drive Specification ST3000VX000 ST2000VX000 ST1000VX000 Altitude non operating below mean sea level max 9304 8m to 12 192m 71000 ft to 40 000 ft 9304 8m to 12 192m 71000 ft to 40 000 ft 304 8m to 12 192m 71000 ft to 40 000 ft Operational Shock max 80 Gs at 2ms 80 Gs at 2ms 80 Gs at 2ms Non Operational Shock max 300 Gs at 2ms 300 Gs at 2ms 350 Gs at 2ms Vibration operating 2Hz to 22Hz 0 25 Gs Limited displacement 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz
3. OF DRIVE T 0 814 in NE d vB 20 68 mm Nera OF CONNECTOR DATUMB Q Y AA 4 00 in 0 138 in 8 401 60 mm 351mm 1 638 in 22 020 in a 224 41 61 mm 0 99 4 51 mm LA 1 028in max 26 11 mm 3X 6 32 UNC 2B IO IE 3 MINIMUM THREAD DEPTH 0 15 MAXIMUM FASTENER PENETRATION BOTH SIDES 3x 0 250 010 in 6 35 25 mm BOTH SIDES i 2x 1 750 in porci 44 45 mm 1 B i 2x 0 125 in Note o 3 18 mm 4X 6 32 UNC 2B DERI 3 MINIMUM THREAD DEPTH 0 15 MAXIMUM FASTENER PENETRATION 2x 3 750 in 95 25 mm Seagate SV35 Series HDD Product Manual Rev E Image is for reference only and may not represent actual drive 16 www seagate com Figure 3 Mounting dimensions 1 Disk 1TB 5 787 in max 146 99 mm 1 106 050 in 28 09 1 27 mm 0 626 050 in 15 90 1 27 mm TOP OF LABEL 4 010 in max Temperature d 101 85 mm Check Point OF DRIVE aue 5 I mm 8 we lt 1 oF CONNECTOR DATUM B 400 138 in 3 51 mm 4 00 in 101 60 mm 1638in i i ren in 41 61 mm 30 99 51 mm Pa 0 787 in max i C 3X 6 32 UNC 2B 49 99 mm 3 MINIMUM THREAD DEPTH amp 9 Ex 0 15 MAXIMUM FASTENER PENETRATION BOTH SIDES 3x 250 010in
4. Product Manual Seagate SV35 Series ST3000VX000 ST2000VX000 ST1000VX000 100687219 Rev E May 2014 Seagate Document Revision History Revision Date Description of Change Rev A 10 20 2011 Initial release Rev B 02 21 2012 Corrected Table 1 Altitude operating specification and Table 3 specification Idle2 Rev C 06 01 2012 Updated features list updated footnotes for Table 1 and Table 2 below 3 5 9 12 19 amp 26 Updated copyright statement updated support URLs Rev D 05 08 2014 updated page numbering amp page layouts updated person from you your to users the added missing hyperlinks to URLs amp added metric values to mechanical drawings Rev E 05 29 2014 Changed Idle2 to Idle1 page 8 2014 Seagate Technology LLC All rights reserved Publication number 100687219 Rev Rev E May 2014 Seagate Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and or other countries SV35 and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and or other countries All other trademarks or registered trademarks are the property of their respective owners No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC Call 877 PUB TEK1 877 782 8351 to request permission When referring
5. 0 e eee ett tees 6 2 5 Physical characteris eS dedic end Race x nm doe eie p edasegededdedereas 6 2 6 SII KM CETT 7 2 7 Start stop tlmes ssa eee he RE ERES Rumes Neu MEG ERE DENEN nee et 7 2 8 Power specifications a ieaiaia A AA aaa E AA eee 8 2 8 1 Power CONSUMPUION oases ee AI a 8 2 8 2 Conducted noise 0 20 teen eee 9 2 8 3 Voltage tolerance oc eps i A RR eae ER RENE dos WA 9 2 8 4 Power management MOdES sesak nne 9 2 9 Environmental specifications apaan dida aa aaa a a a eh 10 2 9 1 Ambient temperature sesak eee 10 2 9 2 Temperature gradient lt 22x x RR Ee rN EEIN TRENN ENNA 10 2 9 3 IU asasi pai a eer Rum X RR RU da ern r a a a a RR Ba 10 2 9 4 AIMIUGC 0244 recs mee nei orto en dere Baa eed dene ee E 10 2 9 5 SOC SERRE ECT IR TIL E DS I OIL 10 2 9 6 Non operating vibration 2 nne 11 2 10 PERANAKAN 11 2 10 1 Test for Prominent Discrete Tones PDTS 11 2 11 Electromagnetic immunity sesen RR eee 12 2 2 jAbR and Warranty rseson coke nes a A4 ed wae eds LEE reme xd Adee ds 12 2 13 Agency certification 0 aan ea hh 12 2 13 1 Safety certification s saa esasa aa akane eee 12 2 13 2 Electromagnetic compatibility 13 2133 POC verification s MA R E ach od teas D E ud 13 2 14 Environmental protection llee m AA 14 2 14 1
6. Serial ATA Revision 3 2 specification One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels All specifications above are based on native configurations 2 2 Formatted capacity Model ae nie ira Bytes per sector ST3000VX000 3000GB 5 860 533 168 ST2000VX000 2000GB 3 907 029 168 4K ST1000VX000 1000GB 1 953 525 168 One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting 2 2 1 LBA mode When addressing these drives in LBA mode all blocks sectors are consecutively numbered from 0 to n 7 where nis the number of guaranteed sectors as defined above See Section 4 3 1 Identify Device command words 60 61 and 100 103 for additional information about 48 bit addressing support of drives with capacities over 137GB Seagate SV35 Series HDD Product Manual Rev E www seagate com 2 3 Default logical geometry Cylinders 16 383 Read write heads 16 Sectors per track 63 LBA mode When addressing these drives in LBA mode all blocks sectors are consecutively numbered from 0
7. burst data transfer rates up to 600MB per second TGMR recording technology provides the drives with increased areal density State of the art cache and on the fly error correction algorithms Native Command Queuing with command ordering to increase performance in demanding applications Full track multiple sector transfer capability without local processor intervention Seagate AcuTrac M servo technology delivers dependable performance even with hard drive track widths of only 75 nanometers Seagate OptiCache technology boosts overall performance by as much as 45 over the previous generation Quiet operation Compliant with RoHS requirements in China and Europe SeaTools diagnostic software performs a drive self test that eliminates unnecessary drive returns Support for S M A R T drive monitoring and reporting Supports latching SATA cables and connectors Worldwide Name WWN capability uniquely identifies the drive www seagate com 1 1 About the SATA interface The Serial ATA SATA interface provides several advantages over the traditional parallel ATA interface The primary advantages include Easy installation and configuration with true plug and play connectivity It is not necessary to set any jumpers or other configuration options Thinner and more flexible cabling for improved enclosure airflow and ease of installation e Scalability to higher performance levels In addition SATA makes the transition from paral
8. to drive capacity one gigabyte or GB equals one billion bytes and one terabyte or TB equals one trillion bytes Your computer s operating system may use a different standard of measurement and report a lower capacity In addition some of the listed capacity is used for formatting and other functions and thus will not be available for data storage Actual quantities will vary based on various factors including file size file format features and application software Actual data rates may vary depending on operating environment and other factors The export or re export of hardware or software containing encryption may be regulated by the U S Department of Commerce Bureau of Industry and Security for more information visit www bis doc gov and controlled for import and use outside of the U S Seagate reserves the right to change without notice product offerings or specifications Contents Seagate Technology Support Services ss eee 1 1 0 INMFOGUCHON P ei ele ee ee ee aaa ea ed ele ae 2 1 1 About the SATA interface maa LE nada PAR D A tte tees 3 2 0 Drive SpecificatiONnS Yi Gate ee ER RIDERE e ERE xs 4 2 1 Specification summary tables ilississesesee tte eee 4 2 2 Forimatted Capacity s s10teceenssedecdedhentiarddhebendedsdaedddaveean edd E 5 2 2 1 BinWue qe D 5 2 3 Default logical geometry satiin enina unane eDane E aa Re 6 2 4 Recording and interface technology 0
9. 0 25 Gs 2Hz to 22Hz 0 25 Gs Limited displacement 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz 0 25 Gs 2Hz to 22Hz 0 25 Gs Limited displacement 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz 0 25 Gs Vibration non operating 5Hz to 22Hz 3 0 Gs 22Hz to 350Hz 3 0 Gs 350Hz to 500Hz 3 0 Gs 5Hz to 22Hz 3 0 Gs 22Hz to 350Hz 3 0 Gs 350Hz to 500Hz 3 0 Gs 5Hz to 22Hz 3 0 Gs 22Hz to 350Hz 3 0 Gs 350Hz to 500Hz 3 0 Gs Drive acoustics sound power Idle Seek 2 4 bels typical 2 6 bels max 2 6 bels typical 2 7 bels max 2 4 bels typical 2 6 bels max 2 6 bels typical 2 7 bels max 2 2 bels typical 2 3 bels max 2 3 bels typical 2 4 bels max Non recoverable read errors 1 per 10 bits read 1 per 1014 bits read 1 per 10 bits read Annualized Failure Rate AFR 196 196 196 Warranty To determine the warranty for a specific drive use a web browser to access the following web page http www seagate com support warranty and replacements From this page click on the Check to see if the drive is under Warranty link The following are required to be provided the drive serial number model number or part number and country of purchase The system will display the warranty information for the drive Load Unload cycles 300 000 300 000 300 000 25 C 50 rel humidity Supports Hotplug operation per the Yes Yes Yes
10. 1 0 006 Sleep 0 63 0 111 0 006 During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels TDIPLM Enabled Seagate SV35 Series HDD Product Manual Rev E www seagate com 2 8 2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80 ohm resistive load on the 12 volt line or an equivalent 15 ohm resistive load on the 5 volt line Using 12 volt power the drive is expected to operate with a maximum of 120 mV peak to peak square wave injected noise at up to 10MHz Using 5 volt power the drive is expected to operate with a maximum of 100 mV peak to peak square wave injected noise at up to 10MHz o Noe Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read write current 2 8 3 Voltage tolerance Voltage tolerance including noise e 5V 5 e 12V 10 7 5 2 8 4 Power management modes The drive provides programmable power management to provide greater energy efficiency In most systems users can control power management through the system setup program The drive features the following power management modes Power modes Heads Spindle Buffer Active Tracking Rotating Enabled Idle Tracking Rotating Enabled Standby Parked Stopped Enabled Sleep Parked Stopped Disabled Active mode The d
11. 6 35 25mm BOTH SIDES 2x 1 625 4 020 in 2x 1 750in 41 28 51 mm 44 45 mm OT 16 9 6 FT ui ed 2x 0 125 in C 3 18 mm o ax 6 32 unc 28 A 3 MINIMUM THREAD DEPTH D 0 15 MAXIMUM FASTENER PENETRATION O 2x 3 750 in 95 25 mm Cc A O0 O OF Note Image is for reference only and may not represent actual drive Seagate SV35 Series HDD Product Manual Rev E www seagate com 4 0 SATA Interface These drives use the industry standard Serial ATA SATA interface that supports FIS data transfers It supports ATA programmed input output PIO modes 0 to 4 multiword DMA modes 0 to 2 and Ultra DMA modes 0 to 6 For detailed information about the SATA interface refer to the Serial ATA High Speed Serialized AT Attachment specification 4 1 Hot Plug compatibility SV35 Series HDD drives incorporate connectors which enable users to hot plug these drives in accordance with the SATA Revision 2 5 specification This specification can be downloaded from www serialata org 4 2 SATA device plug connector pin definitions Table 5 summarizes the signals on the SATA interface and power connectors Table 5 SATA connector pin definitions Segment i Function Definition Signal Ground 2nd mate A Differential sign
12. Ambient temperature 10 ambient temperature 7 8 Annualized Failure Rate 12 areal density 6 ATA commands 19 Australia New Zealand Standard AS NZ CISPR22 13 Australian Communication Authority ACA 13 Australian C Tick 13 Average latency 7 Average seek time 7 B buffer 6 C cables and connectors 15 cache 6 capacity 5 case temperature 10 CE mark 13 certification 12 Check Power Mode 19 China RoHS directive 14 compatibility 13 Conducted noise 9 Conducted RF immunity 12 Configuring the drive 15 connectors 15 Corrosive environment 14 CSA60950 1 12 D data transfer rates 2 DC power 8 Default logical geometry 6 density 6 Device Configuration Freeze Lock 19 Device Configuration Identify 19 Device Configuration Restore 19 Device Configuration Set 19 Device Reset 19 dimensions 16 17 dissipation 8 Download Microcode 19 E Electrical fast transient 12 Electromagnetic compatibility 13 Electromagnetic Compatibility EMC 13 Electromagnetic Compatibility control Regulation 13 Electromagnetic Compatibility Directive 2004 108 EC 13 Electromagnetic immunity 12 Seagate SV35 Series HDD Product Manual Rev E Index Electrostatic discharge 12 electrostatic discharge ESD 15 EN 55022 Class B 13 EN 55024 13 EN60950 12 enclosures 13 Environmental specifications 10 error correction algorithms 2 ESD 15 EU 13 EU RoHS directive 14 European Union EU requirements 13 Execute Device Diagnostics 19
13. European Union Restriction of Hazardous Substances RoHS Directive 14 2 14 2 China Restriction of Hazardous Substances RoHS Directive 14 2 15 Corrosive environment a Pen Pek Sa AA A AN AAA hh 14 3 0 Configuring and Mounting the Drive llseeeeeseeere eee 15 3 1 Handling and static discharge precautions 15 3 2 Configuring the drive ss Ann men EA teens 15 3 3 SATA cables and connectors 060 cece teeta 15 3 4 Drive MOUNTING ni nac heed beer 4 px KA AAA ened Ped e ARA A eed ena 16 4 0 SATA Interace occ ois ove lec sine es dais side ace oe wee Kea seed ad a ee wale 18 4 1 Hot Plug compatibility vee das pede o otn mn than ag poi S dor yeaa ues 18 4 2 SATA device plug connector pin definitions 18 4 3 Supported ATA commands i smi Rer e lesstrfesreerzag eX44esx y noua 19 4 3 1 Identify Device command sesak eh 21 4 3 2 Set Features command daresi daadaa aea dae iia a D a i EE ees 25 4 3 3 S M A R T commands cae ea gece hk Ren Ka RA RU NEE RAE 26 Seagate SV35 Series HDD Product Manual Rev E Figure 1 Attaching SATA cabling llis 15 Figure 2 Mounting dimensions 3 disk STB and 2TB models 16 Figure 3 Mounting dimensions 1 Disk 1TB ssslseleseeeeeee ee 17 Seagate SV35 Series HDD Product Manual Rev E Seagate Technology Support Services For inform
14. Extended 19 Read Native Max Address 19 Read Native Max Address Extended 19 Read Sectors 19 Read Sectors Extended 19 Read Sectors Without Retries 19 Read Verify Sectors 19 Read Verify Sectors Extended 19 Read Verify Sectors Without Retries 20 Read write power 8 Recalibrate 20 recording density 6 recording method 6 Recording technology 6 relative humidity 10 Reliability 12 RF 12 RMS read write current 9 RoHS 14 RRL 13 28 S S M A R T Disable Operations 20 S M A R T Enable Operations 20 S M A R T Enable Disable Autosave 20 S M A R T Execute Offline 20 S M A R T implementation 19 S M A R T Read Attribute Thresholds 20 S M A R T Read Data 20 S M A R T Read Log Sector 20 S M A R T Return Status 20 S M A R T Save Attribute Values 20 S M A R T Write Log sector 20 Safety certification 12 screws 10 Seagate Technology Support Services 1 sectors 5 Security Disable Password 20 Security Erase Prepare 20 Security Erase Unit 20 Security Freeze 20 Security Set Password 20 Security Unlock 20 See S M A R T commands on page 34 19 Seek 20 Seek time 7 Serial ATA SATA interface 18 serial ATA ports 3 servo electronics 8 Set Features 20 Set Max Address 20 Set Max Address Extended 20 Set Multiple Mode 20 Shock 10 single track seeks 7 Sleep 8 9 20 Sleep mode 9 sound 11 Specification summary table 4 spindle speed 6 Spinup 8 Spinup power 8 Standby 8 9 20 Standby Immediate 20 Standb
15. F FCC verification 13 features 2 Flush Cache 19 Flush Cache Extended 19 Format Track 19 Formatted capacity 5 G geometry 6 Gs 11 guaranteed sectors 5 6 H Handling precautions 15 height 6 humidity 10 l I O data transfer rate 6 Identify Device 19 Identify Device command 21 Idle 9 19 Idle Immediate 19 Idle mode 8 9 Information Technology Equipment ITE 13 Initialize Device Parameters 19 Input noise ripple 9 input voltage 8 interface 6 18 interference 13 internal data transfer rate OD 6 is 7 ISO document 7779 11 ITE 13 K KCC 13 Korean Communications Commission 13 Korean RRL 13 L latency 7 LBA mode 5 6 length 6 logical geometry 6 master slave 3 mounting 16 27 mounting screws 10 mounting the drive 15 N noise 9 nominal power 7 Nonoperating shock 11 Nonoperating vibration 11 O operating 8 Operating power 8 Operating shock 10 Operating vibration 11 P Physical characteristics 6 point to point 3 15 Power consumption 8 power dissipation 8 Power modes 9 Power specifications 8 Power management modes 9 Power on to Ready 7 precautions 15 printed circuit board 15 programmable power management 9 prominent discrete tone 11 Q quick reference 4 R Radiated RF immunity 12 radio and television interference 13 radio frequency RF 12 Read Buffer 19 Read DMA 19 Read DMA Extended 19 Read DMA without Retries 19 Read Log Ext 19 Read Multiple 19 Read Multiple
16. Gb in 625Gb in 625Gb in Spindle speed 7200 RPM 7200 RPM 7200 RPM Internal data transfer rate max 2147Mb s 2147Mb s 2147 Mb s Average data rate read write MB s 156MB s 156MB s 156MB s Maximum sustained data rate OD 210MB s 210MB s 210MB s read MB s I O data transfer rate max 600MB s 600MB s 600 MB s Cache buffer 64MB 64MB 64MB Height max 26 1mm 1 028 in 26 1mm 1 028 in 20 17mm 0 7825 in Width max 101 6mm 4 0 in 0 010 in 101 6mm 4 0 in 0 010 in 101 6mm 4 0 in 0 010 in Length max 146 99mm 5 787 in 146 99mm 5 787 in 146 99mm 5 787 in Weight typical 626g 1 38 Ib 626g 1 38 Ib 400g 0 88 Ib Average latency 4 16ms 4 16ms 4 16ms Power on to ready max lt 17 0s lt 17 0s lt 10 0s Standby to ready max lt 17 0s lt 17 0s lt 10 0s Average seek read typical lt 8 5ms typical lt 8 5ms read lt 8 5ms read Average seek write typical lt 9 5ms typical lt 9 5ms write lt 9 5ms write Startup current typical 12V peak 2 0A 2 0A 2 0A Voltage tolerance including noise 5V 5 5V 5 5V 5 12V 10 7 5 12V 10 7 5 12V 10 7 5 Ambient temperature 0 to 70 C operating 40 to 70 C non operating 0 to 70 C operating 40 to 70 C non operating 0 to 70 C operating 40 to 70 C non operating Temperature gradient 20 C per hour max operating 30 C per hour max non operating
17. Removal voids the warranty Some factory installed labels contain information needed to service the drive Other labels are used to seal out dirt and contamination 3 2 Configuring the drive Each drive on the SATA interface connects point to point with the SATA host adapter There is no master slave relationship because each drive is considered a master in a point to point relationship If two drives are attached on one SATA host adapter the host operating system views the two devices as if they were both masters on two separate ports Both drives behave as if they are Device 0 master devices SATA drives are designed for easy installation It is usually not necessary to set any jumpers on the drive for proper operation however if users connect the drive and receive a drive not detected error the SATA equipped motherboard or host adapter may use a chipset that does not support SATA speed auto negotiation 3 3 SATA cables and connectors The SATA interface cable consists of four conductors in two differential pairs plus three ground connections The cable size may be 30 to 26 AWG with a maximum length of one meter 39 37 inches See Table 5 for connector pin definitions Either end of the SATA signal cable can be attached to the drive or host For direct backplane connection the drive connectors are inserted directly into the host receptacle The drive and the host receptacle incorporate features that enable the direct connection to
18. These drives are designed to consistently meet the seek times represented in this manual Physical seeks regardless of mode such as track to track and average are expected to meet the noted values However due to the manner in which these drives are formatted benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications 2 7 Start stop times 3 disk models 2 disk models 1 disk models Power on to ready 15 typical 15 typical 8 5 typical in seconds 17 max 17 max 10 max Standby to ready 15 typical 15 typical 8 5 typical in seconds 17 max 17 max 10 max Ready to spindle stop 10 typical 10 typical 10 typical in seconds 11 max 11 max 11 max Time to ready may be longer than normal if the drive power is removed without going through normal OS powerdown procedures Seagate SV35 Series HDD Product Manual Rev E 7 www seagate com 2 8 Power specifications The drive receives DC power 5V or 12V through a native SATA power connector Refer to Figure 1 on page 15 2 8 10 Power consumption Power requirements for the drives are listed in Table 2 and Table 3 Typical power measurements are based on an average of drives tested under nominal conditions using 5 0V and 12 0V input voltage at 25 C ambient temperature Spinup power Spinup power is measured from the time of power on to the time that the
19. accepts all commands and returns to Active mode when disk access is necessary Seagate SV35 Series HDD Product Manual Rev E 9 www seagate com 2 9 Environmental specifications 2 9 1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive Actual drive case temperature should not exceed 69 C 156 F within the operating ambient conditions Refer to Section 3 4 on page 16 for base plate measurement location Operating 0 to 70 C 32 to 158 F Non operating 40 to 70 C 40 to 158 F 2 9 2 Temperature gradient Operating 20 C per hour 68 F per hour max without condensation Non operating 30 C per hour 86 F per hour max 2 9 3 Humidity 2 9 8 1 Relative humidity Operating 5 to 95 non condensing 30 per hour max Nonoperating 5 to 95 non condensing 30 per hour max 2 9 8 2 Wet bulb temperature Operating 37 7 C 99 9 F max Non operating 40 C 104 F max 2 9 4 Altitude Operating 304 8m to 3048m 1000 ft to 10 000 ft Non operating 304 8m to 12 192m 1000 ft to 40 000 ft 2 9 5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws Shock may be applied in the X Y or Z axis 2 9 5 1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maxi
20. acoustic management 80804 95 99 ATA reserved 0000 100 103 Total number of user addressable LBA sectors available see Section 2 2 for related information These words are required for drives that support the 48 bit addressing feature Maximum value 0000FFFFFFFFFFFFh ST3000VX000 5 860 533 168 ST2000VX000 3 907 029 168 ST1000VX000 1 953 525 168 104 107 ATA reserved 0000 108 111 The mandatory value of the world wide name WWN for the drive NOTE This field is valid if word 84 bit 8 is set to 1 indicating 64 bit WWN Each drive will have a unique value support 112 127 ATA reserved 00004 160 254 ATA reserved 0000 255 Integrity word xXxA5y See the bit descriptions below for words 63 84 and 88 of the Identify Drive data Description if bit is set to 1 Bit Word 63 0 Multiword DMA mode 0 is supported 1 Multiword DMA mode 1 is supported 2 Multiword DMA mode 2 is supported 8 Multiword DMA mode 0 is currently active Multiword DMA mode 1 is currently active 10 Multiword DMA mode 2 is currently active Bit Word 84 0 SMART error login is supported 1 SMART self test is supported Media serial number is supported o AJOJN Media Card Pass Through Command feature set is supported Streaming feature set is supported Seagate SV35 Series HDD Product Manual Rev E 23 www seagate com
21. al pair A from Phy A Ground 2nd mate B Differential signal pair B from Phy B Ground 2nd mate Key and spacing separate signal and power segments Power P1 V33 3 3V power P2 V33 3 3V power P3 V33 3 3V power pre charge 2nd mate P4 Ground 1st mate Ground 2nd mate P6 Ground 2nd mate Vs 5V power pre charge 2nd mate P8 V5 5V power P9 V5 5V power P10 Ground 2nd mate Ground or LED signal If grounded drive does not use deferred spin P12 Ground 1st mate M42 12V power pre charge 2nd mate P14 Vio 12V power P15 M42 12V power Notes 1 All pins are in a single row with a 1 27 mm 0 050 pitch 2 The comments on the mating sequence apply to the case of backplane blindmate connector only In this case the mating sequences are the ground pins P4 and P12 the pre charge power pins and the other ground pins the signal pins and the rest of the power pins 3 There are three power pins for each voltage One pin from each voltage is used for pre charge when installed in a blind mate backplane configuration All used voltage pins V must be terminated Seagate SV35 Series HDD Product Manual Rev E 18 4 3 Supported ATA commands The following table lists SATA standard commands that the drive supports For a detailed description of the ATA commands refer to the Serial ATA International Organization Serial ATA Revision 3 2 http www sata io org See S M A R T commands on pag
22. arantee that all systems will comply with the directives The drive is designed for operation inside a properly designed enclosure with properly shielded I O cable if necessary and terminators on all unused I O ports Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products Korean RRL If these drives have the Korean Communications Commission KCC logo they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility EMC Framework requirements of the Radio Research Laboratory RRL Communications Commission Republic of Korea These drives have been tested and comply with the Electromagnetic Interference Electromagnetic Susceptibility EMI EMS for Class B products Drives are tested in a representative end user system by a Korean recognized lab Family name SV35 Series Certificate number KCC REM STX Barracuda Australian C Tick N176 If these models have the C Tick marking they comply with the Australia New Zealand Standard AS NZ CISPR22 and meet the Electromagnetic Compatibility EMC Framework requirements of the Australian Communication Authority ACA 2 13 3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure not attached as an external device As such each drive is considered to be a subassembly even when it is individua
23. ard assembly PCBA or exposed to an ambient relative humidity greater than 95 Materials used in cabinet fabrication such as vulcanized rubber that can outgas corrosive compounds should be minimized or eliminated The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide free alternatives Seagate SV35 Series HDD Product Manual Rev E 14 www seagate com 3 0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive 3 1 Handling and static discharge precautions After unpacking and before installation the drive may be exposed to potential handling and electrostatic discharge ESD hazards Observe the following standard handling and static discharge precautions Caution Before handling the drive put on a grounded wrist strap or ground oneself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet Wear a grounded wrist strap throughout the entire installation procedure Handle the drive by its edges or frame only The drive is extremely fragile handle it with care Do not press down on the drive top cover Always rest the drive on a padded antistatic surface until users mount it in the computer Do not touch the connector pins or the printed circuit board Do not remove the factory installed labels from the drive or cover them with additional labels
24. ation regarding online support and services visit_http www seagate com about contact us technical support Available services include Presales amp Technical support e Global Support Services telephone numbers amp business hours e Authorized Service Centers For information regarding Warranty Support visit http www seagate com support warranty and replacements For information regarding data recovery services visit http www seagate com services software data recovery services For Seagate OEM and Distribution partner portal visit http www seagate com partners For Seagate reseller portal visit http www seagate com partners my spp dashboard Seagate SV35 Series HDD Product Manual Rev E 1 1 0 Introduction This manual describes the functional mechanical and interface specifications for the following Seagate SV35 Series model drives ST3000VX000 ST2000VX000 ST1000VX000 These drives provide the following key features Seagate SV35 Series HDD Product Manual Rev E Enterprise class reliability for 24x7 video surveillance applications Thermal monitoring and reporting for 24x7 operations Uncompromising reliability supports flexible surveillance design with case temperatures up to 70 C Performance tuned for seamless video applications Built in error recovery for non stop video streaming Best in class acoustic performance means virtually silent operation 7200 RPM spindle speed High instantaneous
25. be hot pluggable and blind mateable For installations which require cables users can connect the drive as illustrated in Figure 1 Figure 1 Attaching SATA cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation SV35 Series HDD drives support latching SATA connectors Seagate SV35 Series HDD Product Manual Rev E 15 3 4 Drive mounting Users can mount the drive in any orientation using four screws in the side mounting holes or four screws in the bottom mounting holes See Figure 2 and Figure 3 for drive mounting dimensions Follow these important mounting precautions when mounting the drive Allow a minimum clearance of 0 030 inches 0 76mm around the entire perimeter of the drive for cooling Use only 6 32 UNC mounting screws The screws should be inserted no more than 0 150 inch 3 81mm into the bottom or side mounting holes Do not overtighten the mounting screws maximum torque 6 inch lb Figure 2 Mounting dimensions 3 disk 3TB and 2TB models 5 787 in max Xo 146 99 mm 1 013 050 in 25 73 1 27 mm i 0 680 050 in 17 27 1 27 mm TOP OF LABEL 4 040 in max Temperature H 101 85 mm i Check Point EF
26. commands are identified by the value Password 014 placed in the Set Max Features register Lock 024 as defined to the right Unlock 034 Freeze Lock 044 Set Max Address Extended 374 Set Multiple Mode C6 Sleep E64 S M A R T Disable Operations BOy D9 S M A R T Enable Disable Autosave BOy D2 S M A R T Enable Operations BOH D8 S M A R T Execute Offline BOy D444 S M A R T Read Attribute Thresholds Boy D1u S M A R T Read Data BOH DOH S M A R T Read Log Sector Boy D54 S M A R T Return Status Boy DAY S M A R T Save Attribute Values Boy D3y S M A R T Write Log Sector BOH D6 Standby E2y Standby Immediate EO Write Buffer E8y Write DMA CAy Write DMA Extended 35H Write DMA FUA Extended 3Dy Write DMA Without Retries CBy Write Log Extended 3Fy Write Multiple C5y Seagate SV35 Series HDD Product Manual Rev E 20 www seagate com Command name Command code in hex Write Multiple Extended 39u Write Multiple FUA Extended CE4 Write Sectors 304 Write Sectors Without Retries 314 Write Sectors Extended 344 Write Stream DMA Extended 3Ay Write Stream Extended 3By Write Uncorrectable 454 4 3 1 Identify Device command The Identify Device command command code ECy transfers information about the drive to the host following power up The data is organized as a single 512 byte block of data whose contents are shown in on page 19 All reserved bits or words should be set to
27. drive spindle reaches operating speed Read write power and current Read write power is measured with the heads on track based on a 16 sector write followed by a 32 ms delay then a 16 sector read followed by a 32 ms delay Operating power and current Operating power is measured by simulating a typical PVR operating environment using a 50 write 50 read algorithm Idle mode power Idle mode power is measured with the drive up to speed with servo electronics active and with the heads in a random track location Standby mode During Standby mode the drive accepts commands but the drive is not spinning and the servo and read write electronics are in power down mode Table 2 DC power requirements 3 disk 3TB and 2TB Power dissipation 3 disk values shown Avg watts 25 C Avg 5V typ amps Avg 12V typ amps Spinup 2 0 peak Idle1 T 5 40 0 190 0 377 Operating 8 00 0 510 0 462 Standby 0 75 0 136 0 005 Sleep 0 75 0 136 0 005 During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels T DIPLM Enabled Table 3 DC power requirements 1 disk ITB Power dissipation 1 disk values shown Avg watts 25 C Avg 5V typ amps Avg 12V typ amps Spinup 2 0 peak Idle1 t 3 36 0 152 0 216 Operating 5 90 0 500 0 329 Standby 0 63 0 11
28. e 26 for details and subcommands used in the S M A R T implementation Command name Command code in hex Check Power Mode E5y Configure Stream 514 Device Configuration Freeze Lock B1y Cty Device Configuration Identify B1y C24 Device Configuration Restore Bip COH Device Configuration Set B14 C3H Device Reset 08H Download Microcode 924 Execute Device Diagnostics 904 Flush Cache E74 Flush Cache Extended EA Format Track 504 Identify Device ECy Idle E34 Idle Immediate Ely Initialize Device Parameters 914 Read Buffer E44 Read DMA C8y Read DMA Extended 254 Read DMA Without Retries C94 Read Log Ext 2Fy Read Multiple C4y Read Multiple Extended 294 Read Native Max Address F84 Read Native Max Address Extended 274 Read Sectors 204 Read Sectors Extended 244 Read Sectors Without Retries 214 Read Stream DMA Extended 2Ay Read Stream Extended 2By Read Verify Sectors 404 Read Verify Sectors Extended 424 Seagate SV35 Series HDD Product Manual Rev E www seagate com Command name Command code in hex Read Verify Sectors Without Retries 414 Recalibrate 104 Security Disable Password F64 Security Erase Prepare F34 Security Erase Unit F44 Security Freeze F54 Security Set Password Fly Security Unlock F24 Seek 704 Set Features EFy Set Max Address F94 Note Individual Set Max Address Address 004
29. eliability The consumer electronics environment of power on hours temperature and I O duty cycle affect the product AFR The AFR will be degraded if used in an enterprise application To determine the warranty for a specific drive use a web browser to access the following web page http www seagate com support warranty and replacements From this page click on the Check to see if the drive is under Warranty link The following are required to be provided the drive serial number model number or part number and country of purchase The system will display the warranty information for the drive 2 13 Agency certification 2 13 1 Safety certification These products are certified to meet the requirements of UL60950 1 CSA60950 1 and EN60950 and so marked as to the certify agency Seagate SV35 Series HDD Product Manual Rev E 12 www seagate com 2 13 2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union EU requirements specified in the Electromagnetic Compatibility Directive 2004 108 EC as put into place 20 July 2007 Testing is performed to the levels specified by the product standards for Information Technology Equipment ITE Emission levels are defined by EN 55022 Class B and the immunity levels are defined by EN 55024 Drives are tested in representative end user systems Although CE marked Seagate drives comply with the directives when used in the test systems we cannot gu
30. he dealer or an experienced radio television technician for additional suggestions Users may find helpful the following booklet prepared by the Federal Communications Commission How to Identify and Resolve Radio Television Interference Problems This booklet is available from the Superintendent of Documents U S Government Printing Office Washington DC 20402 Refer to publication number 004 000 00345 4 Seagate SV35 Series HDD Product Manual Rev E 13 www seagate com 2 14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide including regulations restricting certain chemical substances 2 14 1 European Union Restriction of Hazardous Substances RoHS Directive The European Union Restriction of Hazardous Substances RoHS Directive restricts the presence of chemical substances including Lead Cadmium Mercury Hexavalent Chromium PBB and PBDE in electronic products effective July 2006 This drive is manufactured with components and materials that comply with the RoHS Directive 2 14 2 China Restriction of Hazardous Substances RoHS Directive P N BRAI fe ES 4s HB This product has an Environmental Protection Use Period EPUP of 20 years The following table contains information mandated by China s Marking Requirements for Control of Pollution Caused by Electronic Information Products Standard 20 12 mA OEM RIEA EPU o FReST RPE Pune iem PICS XE PTE RIES Toxic
31. l Reference standard Electrostatic discharge Contact HCP VCP 4 kV Air 8 kV EN61000 4 2 95 Radiated RF immunity 80MHz to 1 000MHz 3 V m EN61000 4 3 96 80 AM with 1kHz sine ENV50204 95 900MHz 3 V m 5096 pulse modulation 200Hz Electrical fast transient t 1 kV on AC mains 0 5 kV on external I O EN61000 4 4 95 Surge immunity t 1 kV differential 2 kV common EN61000 4 5 95 AC mains Conducted RF immunity 150kHz to 80MHz 3 Vrms 80 AM with 1kHz EN61000 4 6 97 sine Voltage dips interrupts 096 open 5 seconds EN61000 4 11 94 096 short 5 seconds 40 0 10 seconds 7096 0 01 seconds 2 12 AFR and Warranty The product will achieve an Annualized Failure Rate AFR of 196 when operated in an environment of ambient air temperatures of 25 C Operation at temperatures outside the specifications shown in Environmental specifications on page 10 may increase the product AFR AFR is a population statistics that is not relevant to individual units AFR specifications are based on the following assumptions for consumer electronics environments 8760 power on hours per year 10 000 average motor start stop cycles per year Operations at nominal voltages Temperatures outside the specifications in Environmental specifications on page 10 may reduce the product reliability Normal I O duty cycle for consumer electronics environments Operation at excessive I O duty cycle may degrade product r
32. l SATA devices behave like Device 0 devices For additional information about how SATA emulates parallel ATA refer to the Serial ATA International Organization Serial ATA Revision 3 2 The specification can be downloaded from www sata io org Seagate SV35 Series HDD Product Manual Rev E 3 2 0 Drive Specifications Unless otherwise noted all specifications are measured under ambient conditions at 25 C and nominal power For convenience the phrases the drive and this drive are used throughout this manual to indicate the following drive models ST3000VX000 ST2000VX000 ST1000VX000 2 1 Specification summary tables The specifications listed in Table 1 are for quick reference For details on specification measurement or definition refer to the appropriate section of this manual Table 1 Drive specifications summary for 3TB 2TB and 1TB models Drive Specification ST3000VX000 ST2000VX000 ST1000VX000 Formatted capacity 3000GB 2000GB 1000GB 512 bytes sector 3TB 2TB 1TB Guaranteed sectors 5 860 533 168 3 907 029 168 1 953 525 168 Heads 6 6 2 Disks 3 3 1 Bytes per sector 4K physical 4096 4096 4096 emulated at 512 byte sectors Default sectors per track 63 63 63 Default read write heads 16 16 16 Default cylinders 16 383 16 383 16 383 Recording density max 1807kFCI 1807kFCI 1807kFCI Track density avg 352 ktracks in 352 ktracks in 352 ktracks in Areal density avg 625
33. lel ATA easy by providing legacy software support SATA was designed to allow users to install a SATA host adapter and SATA disk drive in the current system and expect all of the existing applications to work as normal The SATA interface connects each disk drive in a point to point configuration with the SATA host adapter There is no master slave relationship with SATA devices like there is with parallel ATA If two drives are attached on one SATA host adapter the host operating system views the two devices as if they were both masters on two separate ports This essentially means both drives behave as if they are Device 0 master devices The host adapter may optionally emulate a master slave environment to host software where two devices on separate SATA ports are represented to host software as a Device 0 master and Device 1 slave accessed at the same set of host bus addresses A host adapter that emulates a master slave environment manages two sets of shadow registers This is not a typical SATA environment The SATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software The Command and Control Block registers PIO and DMA data transfers resets and interrupts are all emulated The SATA host adapter contains a set of registers that shadow the contents of the traditional device registers referred to as the Shadow Register Block Al
34. lly marketed to the customer As a subassembly no Federal Communications Commission verification or certification of the device is required Seagate has tested this device in enclosures as described above to ensure that the total assembly enclosure disk drive motherboard power supply etc does comply with the limits for a Class B computing device pursuant to Subpart J Part 15 of the FCC rules Operation with non certified assemblies is likely to result in interference to radio and television reception Radio and television interference This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer s instructions may cause interference to radio and television reception This equipment is designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television which can be determined by turning the equipment on and off users are encouraged to try one or more of the following corrective measures Reorient the receiving antenna Move the device to one side or the other of the radio or TV Move the device farther away from the radio or TV Plug the computer into a different outlet so that the receiver and computer are on different branch outlets If necessary users should consult t
35. mum operating shock of 80 Gs based on half sine shock pulses of 2 ms during read operations Shocks should not be repeated more than two times per second Seagate SV35 Series HDD Product Manual Rev E 10 www seagate com 2 9 5 2 Non operating shock 3TB and 2TB models The non operating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a non repetitive half sine shock pulse of 2 ms duration 1TB model The non operating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on a non repetitive half sine shock pulse of 2 ms duration 2 9 5 3 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below 2Hz to 22Hz 0 25 Gs Limited displacement 22Hz to 350Hz 0 50 Gs 350Hz to 500Hz 0 25 Gs All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws Vibration may be applied in the X Y or Z axis Throughput may vary if improperly mounted 2 9 6 Non operating vibration The maximum non operating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation a
36. or Hazardous Substances or Elements sti Sh Matiz Hexavalent Polybrominated Paolybrominated Diphenyl Diphery Ether SR LRL AH O indicates the hazardous and toxic substance content of the part at the homogeneous material level is lower than the threshold defined by the China ROHS MCV Standard ORRA FARM me LE ME eke Ae ee RTF RoHS MCV brite Fite SS TTE B X indicates the hazardous and toxic substance content of the part at the homogeneous material level is over the threshold defined by the China ROHS MCV Standard K RRA FARE ME BUS CRUS ae eB LF RoHS MCV baie ite CBT B 2 15 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases chlorine and nitric oxide classes G and H per ASTM B845 However this accelerated testing cannot duplicate every potential application environment Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment The silver copper nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide chloride and nitrate contaminants Sulfur is found to be the most damaging In addition electronic components should never be exposed to condensing water on the surface of the printed circuit bo
37. re specified below 5Hz to 22Hz 3 0 Gs Limited displacement 22Hz to 350Hz 3 0 Gs 350Hz to 500Hz 3 0Gs 2 10 Acoustics Drive acoustics are measured as overall A weighted acoustic sound power levels no pure tones All measurements are consistent with ISO document 7779 Sound power measurements are taken under essentially free field conditions over a reflecting plane For all tests the drive is oriented with the cover facing upward For seek mode tests the drive is placed in seek mode only The number of seeks per second is defined by the following equation Number of seeks per second 0 4 average latency average access time 2 10 1 Test for Prominent Discrete Tones PDTs Seagate follows the ECMA 74 standards for measurement and identification of PDTs An exception to this process is the use of the absolute threshold of hearing Seagate uses this threshold curve originated in ISO 389 7 to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA 74 standards Seagate SV35 Series HDD Product Manual Rev E 11 www seagate com 2 11 Electromagnetic immunity When properly installed in a representative host system the drive operates without errors or degradation in performance when subjected to the radio frequency RF environments defined in Table 4 Table 4 Radio frequency environments Description Performance leve
38. rive is in Active mode during the read write and seek operations Idle mode The buffer remains enabled and the drive accepts all commands and returns to Active mode any time disk access is necessary Standby mode The drive enters Standby mode when the host sends a Standby Immediate command If the host has set the standby timer the drive can also enter Standby mode automatically after the drive has been inactive for a spec ifiable length of time The standby timer delay is established using a Standby or Idle command In Standby mode the drive buffer is enabled the heads are parked and the spindle is at rest The drive accepts all com mands and returns to Active mode any time disk access is necessary Sleep mode The drive enters Sleep mode after receiving a Sleep command from the host In Sleep mode the drive buffer is disabled the heads are parked and the spindle is at rest The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host After receiving a reset the drive exits Sleep mode and enters Standby mode with all current translation parameters intact Idle and Standby timers Each time the drive performs an Active function read write or seek the standby timer is reinitialized and begins counting down from its specified delay times to zero If the standby timer reaches zero before any drive activity is required the drive makes a transition to Standby mode In both Idle and Standby mode the drive
39. ster are defined as follows 02 Enable write cache default 03 Set transfer mode based on value in Sector Count register Sector Count register values 004 Set PIO mode to default PIO mode 2 O14 Set PIO mode to default and disable IORDY PIO mode 2 O84 PIO mode 0 094 PIO mode 1 0A PIO mode 2 OB PIO mode 3 0Cy PIO mode 4 default 204 Multiword DMA mode 0 214 Multiword DMA mode 1 224 Multiword DMA mode 2 404 Ultra DMA mode 0 414 Ultra DMA mode 1 424 Ultra DMA mode 2 434 Ultra DMA mode 3 444 Ultra DMA mode 4 454 Ultra DMA mode 5 464 Ultra DMA mode 6 104 Enable use of SATA features 55 Disable read look ahead read cache feature 82 Disable write cache 904 Disable use of SATA features AA Enable read look ahead read cache feature default Fip Report full capacity available At power on or after a hardware or software reset the default values of the features are as indicated above Seagate SV35 Series HDD Product Manual Rev E www seagate com 4 3 3 S M A R T commands S M A R T provides near term failure prediction for disk drives When S M A R T is enabled the drive monitors predetermined drive attributes that are susceptible to degradation over time If self monitoring determines that a failure is likel
40. to n 1 where nis the number of guaranteed sectors as defined above 2 4 Recording and interface technology Interface SATA Recording method TGMR Recording density kFCI 1807 Track density ktracks inch avg 352 Areal density Gb in avg 625 Spindle speed RPM 7200 0 2 Internal data transfer rate Mb s max 2147 Maximum sustained data transfer rate OD read MB s 210 Average data rate read write MB s 156 I O data transfer rate MB s max 600 2 5 Physical characteristics Maximum height 3TB and 2TB 26 1mm 1 028 in 1TB 20 17mm 0 7825 in Maximum width all models 101 6mm 4 0 in 0 010 in Maximum length all models 146 99mm 5 787 in Typical weight 3TB and 2TB 626g 1 38 Ib 1TB 400g 0 88 Ib Cache buffer 64MB 64 768kb Seagate SV35 Series HDD Product Manual Rev E 6 www seagate com 2 6 Seek time Seek measurements are taken with nominal power at 25 C ambient temperature All times are measured using drive diagnostics The specifications in the table below are defined as follows Track to track seek time is an average of all possible single track seeks in both directions Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks less overhead Typical seek times ms Read Write Track to track 1 0 1 2 Average 8 5 9 5 Average latency 4 16
41. transferred during a Read Multiple XXXXy or Write Multiple command 60 61 Total number of user addressable LBA sectors available OFFFFFFFh see Section 2 2 for related information Note The maximum value allowed in this field is OFFFFFFFh 268 435 455 sectors 137GB Drives with capacities over 137GB will have OFFFFFFFh in this field and the actual number of user addressable LBAs specified in words 100 103 This is required for drives that support the 48 bit addressing feature 62 Retired 0000 63 Multiword DMA active and modes supported XXOT7 H4 see note following this table 64 Advanced PIO modes supported modes 3 and 4 supported 00034 65 Minimum multiword DMA transfer cycle time per word 120 nsec 00784 66 Recommended multiword DMA transfer cycle time per word 120 nsec 00784 67 Minimum PIO cycle time without IORDY flow control 240 nsec 00784 68 Minimum PIO cycle time with IORDY flow control 120 nsec 00784 76 SATA capabilities XXXXH 77 Reserved for future SATA definition XXXXH 78 SATA features supported XXXXH 79 SATA features enabled XXXXH 82 Command sets supported 364By 83 Command sets supported 7F094 84 Command sets support extension see note following this table 4163H 85 Command sets enabled 30XXH 22 www seagate com Word Description Value 88 Ultra DMA support and current mode see note following this table XX7F 4 89 Security erase time 00394 90 Enhanced security erase time 00394 94 Automatic
42. y S M A R T makes a status report available to the host Not all failures are predictable S M A R T predictability is limited to the attributes the drive can monitor For more information on S M A R T commands and implementation see the Draft ATA 5 Standard SeaTools diagnostic software activates a built in drive self test DST S M A R T command for D4 that eliminates unnecessary drive returns The diagnostic software ships with all new drives and is also available at http seatools seagate com This drive is shipped with S M A R T features disabled Users must have a recent BIOS or software package that supports S M A R T to enable this feature The table below shows the S M A R T command codes that the drive uses Code in features register S M A R T command DOH S M A R T Read Data D24 S M A R T Enable Disable Attribute Autosave D34 S M A R T Save Attribute Values D44 S M A R T Execute Off line Immediate runs DST D54 S M A R T Read Log Sector D64 S M A R T Write Log Sector D84 S M A R T Enable Operations D94 S M A R T Disable Operations DA S M A R T Return Status If an appropriate code is not written to the Features Register the command is aborted and 0x04 abort is written to the Error register Seagate SV35 Series HDD Product Manual Rev E 26 A ACA 13 acceleration 11 acoustics 11 Active 9 Active mode 9 Agency certification 12 altitude 10
43. y mode 8 9 standby timer 9 Standby to Ready 7 Start stop times 7 static discharge 15 subassembly 13 support services 26 Surge immunity 12 T technical support services 26 temperature 7 10 temperature gradient 10 timer 9 timers 9 Seagate SV35 Series HDD Product Manual Rev E track density 6 Track to track 7 Track to track seek time 7 U UL60950 1 12 V voltage 8 Voltage dips interrupts 12 Voltage tolerance 9 Ww weight 6 wet bulb temperature 10 width 6 Write Buffer 20 Write DMA 20 Write DMA Extended 20 Write DMA FUA Extended 20 Write DMA Without Retries 20 Write Log Extended 20 Write Multiple 20 Write Multiple Extended 21 Write Multiple FUA Extended 21 Write Sectors 21 Write Sectors Extended 21 Write Sectors Without Retries 21 Seagate SV35 Series HDD Product Manual Rev E 29 Seagate C Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard Cupertino California 95014 United States 408 658 1000 ASIA PACIFIC Seagate Singapore International Headquarters Pte Ltd 7000 Ang Mo Kio Avenue 5 Singapore 569877 65 6485 3888 EUROPE MIDDLE EAST AND AFRICA Seagate Technology SAS 16 18 rue du D me 92100 Boulogne Billancourt France 33 1 4186 10 00 Publication Number 100687219 Rev E May 2014
44. zero Parameters listed with an x are drive specific or vary with the state of the drive The following commands contain drive specific features that may not be included in the SATA specification Word Description Value 0 Configuration information 0C5Ay Bit 15 0 2 ATA 1 ATAPI Bit 7 removable media Bit 6 removable controller Bit 0 reserved 1 Number of logical cylinders 16 383 2 ATA reserved 00004 3 Number of logical heads 16 4 Retired 0000 5 Retired 00004 6 Number of logical sectors per logical track 63 003Fy 10 19 Serial number 20 ASCII characters 00004 none 20 Retired 21 Retired 22 Obsolete 23 26 Firmware revision 8 ASCII character string padded with blanks to end of string 27 46 Drive model number 40 ASCII characters padded with blanks to end of string 47 Bits 7 0 Maximum sectors per interrupt on Read multiple and Write 80104 multiple 16 49 Standard Standby timer IORDY supported and may be disabled 2FO0 Seagate SV35 Series HDD Product Manual Rev E 21 www seagate com Seagate SV35 Series HDD Product Manual Rev E Word Description Value 50 ATA reserved 0000 51 PIO data transfer cycle timing mode 02004 52 Retired 0200 55 Number of current logical heads XXXXH 56 Number of current logical sectors per logical track XXXXH 57 58 Current capacity in sectors XXXXy 59 Number of sectors
Download Pdf Manuals
Related Search