Manual 3353
Contents
1. damage to the retina of the eye Direct viewing of this radiation should be avoided at all times Page 7 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Receiver LEDs LED Status Definition Power On Indicates that correct power has been applied 3G Rate Off Indicates no 3G SDI data rate lock On Indicates 3G SDI data rate lock at 2 97 Gbps or 2 97 1 001 Gbps HD Rate Off Indicates no HD SDI data rate lock On Indicates HD SDI data rate lock at 1 485 Gbps or 1 485 1 001 Gbps SD Rate Off Indicates no SD SDI or DVB ASI data rate lock On Indicates SD SDI or DVB ASI data rate lock at 270 Mbps Alarm On Loss of optical signal Note The 3G HD and SD LEDs indicators are off when a non standard signal is applied Rotary Switch Positions Position Function 0 Will mute the audio output 1 through 8 Will output the respective audio channel pair on the HDMI cable and the audio output connectors 9 Not used Indicator LEDs The Fiberlink 3353 Series has four integral indicator LEDs that are used to monitor the state of the unit Audio Pair Selection The Fiberlink 3353 Series has a rotary dial switch that allows you to select which audio pair to output The chart below describes the operation of the rotary switch positions Audio Pair Selection LED Indicators Page 8 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series 1080p Displays with HDMI input using Audio2. 360 Series allows you to transmit 3G HD or SD SDI as per SMPTE 424M 2006 292 and 259 with the ability to embed up to 8 channels 4 pairs of AES EBU digital audio Convenient switches on the 3360 Series transmitter allow the operator to embed each of the four pairs of audio independently to strip previously serialized audio or to pass it through without modification At the receive end of the fiber optic link the operator can decide which audio pairs they need de embedded Audio signals are not required to operate the Fiberlink 3360 link and it can be used as a stand alone 3G HD SD SDI optical link Previously serialized data is left intact throughout the entire transmission process and the 3360 Series is immune to pathological signals over the entire budget link and operating temperature range Signals are equalized and re clocked prior to fiber optic transmission and the 3361 receiver features a re clocked SDI output The 3360 Series is compliant with SMPTE 297 2006 and has the ability to operate seamlessly with Fiberlink Matrix and other SMPTE 297 2006 fiber optic compliant devices Available in card versions and a small footprint box version it is ideal for broad cast or corporate studios OB vans rental and staging auditoriums stadiums and theaters airport or transportation hubs distance learning surgical or medical imaging and more Learn more at commspecial com Fiberlink 3360 3G HD SD SDI amp 4 Pair AES Audio Serie
3. 65 6396 0138 RMA numbers can also be obtained from our web site commspecial com Please have your serial number available Warranty Page 12 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Accessories and Related Products Fiberlink 6610 Visible Light Source The Fiberlink Visible Light Source provides a visible 650 nm laser output that can be used for identifying fiber breaks and individual fibers within fiber bundles allowing for convenient on site testing of fiber networks during construction and maintenance procedures Fiberlink 6615 Optical Power Meter The Fiberlink Optical Power Meter measures the power of optical signals at 850 980 1310 and 1550 nm wavelengths allowing for convenient on site testing of fiber networks during construction and maintenance procedures It can be used to measure the power of an optical signal reaching the receiving end of a fiber optic cable as generated either by a transmitter unit or by a light source such as the 6620 Fiberlink 6620 Three Wavelength Light Source The Fiberlink Three Wavelength Light Source offers a laser output at wavelengths of 1310 and 1550 nm and VCSEL output at 850 nm allowing for convenient on site testing of fiber networks during construction and maintenance procedures Page 13 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Accessories and Related Products The Fiberlink 3
4. Channel Pair 1 1080p Displays with DVI input using Audio Channel Pair 2 3360 Tx 3G HD SD SDI Source 3353 Rx 3355 Rx 3353 Rx 3355 Rx Fiber Cable Fiber Cable Fiber Cable Fiber Cable Fiber Cable 3353 Rx Fiber Cable Fiber Cable Scan Do HD DVI or Analog RGB to 3G HD SD SDI Scan Converter Multichannel Audio Fiberlink Matrix or SMPTE 297 2006 Compatible Switch Router 3350 Tx 3G HD SD SDI Source 1080p Displays with HDMI input 3353 Rx Fiber Cable 3G HD SD SDI Loop Thru Sample Application Diagrams Page 9 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Operating Pointers Remember to check attenuation of the fiber optic cable The system will only operate properly if these specifications fall within the range of the system s loss budget Note If no signal is applied to the 3353 Transmitter no optical power will be present on the 3353 Transmitter s output Troubleshooting Multimode fiber optic cable contains an optical fiber with a light carrying core that is only 0025 inches 62 5 microns in diameter Single mode fiber optic cable has an even smaller core only 00032 to 0004 inches 8 10 microns This is smaller than a human hair Therefore any minute particles of dirt or dust can easily block the fiber from accepting or radiating light To prevent this from happening always use the provided dust caps when ev
5. Front panel selection of one of 8 audio channel pairs on SDI signal to output NOTE Audio on HDMI and line level are available simultaneoulsy and extracted from audio embedded within SDI signal in accordance with SMPTE standards 3G HD SD SDI Output Signal Level 800mV 10 DC Offset 0V 0 5V Rise Fall Time lt 135 ps at 2 97 Gbps per SMPTE 424M lt 270 ps at 1 485 Gbps per SMPTE 292 0 4 ns to 1 5 ns at 270 Mbps per SMPTE 259M Overshoot lt 10 of amplitude Timing Jitter lt 0 2 UI at 270 Mbps lt 1 0 UI at 1 485 Gbps lt 2 0 UI at 2 97 Gbps with color bar signal Alignment Jitter lt 0 2 UI at 270 Mbps lt 0 2 UI at 1 485 Gbps lt 0 3 UI at 2 97 Gbps with color bar signal Re clocking At 270 Mbps 1 485 Gbps amp 2 97 Gbps Technical Specifications Technical Specifications Page 6 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Figure 1 Power Connector DC Input Polarity 9 24 Volts AC or DC Positive Negative Installation Instructions The Fiberlink 3353 Series of fiber optic transmission systems are ready for immediate use and do not require any special tools However an Optical Power Meter such as the Fiberlink 6615 can be useful in determining optical loss budgets during your systems design and maintenance Fiberlink 3353 will operate with the Fiberlink 3350 Fiberlink 3360 Fiberlink 3370 Fiberlink 3380 Scan Do HD Fiberlink Matrix and SMPTE 297 2006
6. Single Color Black Single Color Black on Black Background If you need to use the CSI logo on a non solid background use the Photoshop Layered Files 2005 Spectra Vision Productions Inc Fiberlink 3353 Series 3G HD SD SDI to HDMI Optical Receiver World Headquarters 55 Cabot Court Hauppauge New York 11788 USA Tel 631 273 0404 Fax 631 273 1638 info commspecial com Asia Communications Specialties Pte Ltd 100 Beach Road 22 09 Shaw Tower Singapore 189702 Tel 65 6391 8790 Fax 65 6396 0138 csiasia commspecial com commspecial com Communications Specialties Fiberlink 3353 User s Manual The Fiberlink 3353 Series converts broadcast quality 3G HD SD SDI transmitted over one single mode or multimode fiber to HDMI with or without embedded audio Page 2 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Contents Welcome 3 Features 3 Package Contents 3 Technical Specifications Model Part Number Specifications 4 General Specificat
7. compliant optical tranmission units The following procedure presumes you have followed the instructions for installing your optical transmitter unit The following instructions describe the typical installation procedure 1 Connect the fiber optic cable to the optical input of the receiver unit 2 Connect the video output cable HDMI to the video output HDMI connector on the receiver unit 3 Optionally connect any audio cables and using the channel pair rotary selector choose your desired audio output channel Audio is also embedded on the HDMI cable 4 Terminate any unused BNC output connector at 75 Ohms 5 Connect the Universal Power Supply to the transmitter and receiver units Please refer to figure 1 6 When power is applied the green POWER LED should illuminate indicating the presence of operating power The 3G HD SD RATE LED will give an indication as described in the Indicator LED s and Alarm Circuitry section of this manual 7 The system should now be operational Installation Instructions The transmitting element in the Fiberlink 3350 3360 3370 and 3380 transmitter units contains a solid state Laser Diode located in the optical connector This device emits invisible infrared electromagnetic radiation which can be harmful to human eyes The radiation from this optical connector if viewed at close range with no fiber optic cable connected to the optical connector may be sufficient intensity to cause instantaneous
8. e Fiberlink 3353 This User s Manual Welcome Features Package Contents Page 4 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Model Part Number Specification Unit Type Part Number Receiver Box 3353 B7L LC 3353 B7S ST General Specifications Indicators Power Alarm Data Rate Lock 3G HD SD Box Version Dimensions 6 5 W x 1 15 H x 6 L inches 165 W x 29 H x 152 L mm Weight 16 ounces 453 5 grams Power 9 24 volts AC or DC 5 5 watts Operating Temperature 10 C to 50 C Fiber Optic Input SMPTE 297 2006 Labeling PC ABCD 1310 1550 Connector LC receptacle PC polish or ST Wavelength 1100 1620 nm Minimum Input Sensitivity 17 dBm at 2 97 Gbps 20 dBm at 1 485 Gbps 23 dBm at 270 Mbps Maximum Input Power 0 dBm Video Output Number of Outputs 1 Connector Type HDMI Female Signal Format Single link HDMI with embedded audio RGB or YCrCb as negotiated with display Resolutions Supported All 3G HD SD SDI formats from standard definition to 1080p 60 3G HD SD SDI Output Standard Follows fiber optic input HDCP Compliant Yes SDI signals by definition are not encrypted Technical Specifications Technical Specifications Page 5 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Audio Output Optical Input Number of Audio Channels 2 channels unbalanced line level 2 channels embedded in HDMI signal Audio Connector RCA Jacks Switches
9. er optical connectors are exposed to air It is also a good idea to gently clean the tip of an optical connector with a lint free cloth moistened with alcohol whenever dust is suspected The status of the LEDs should provide the first clue as to the origin of any operational failure If these are off it usually means that the fiber is broken or has too much attenuation Next be certain that the input and output signal connections are correct An optical power meter such as the Fiberlink 6615 a visible light source such as the Fiberlink 6610 and a Three Wavelength Light Source such as the Fiberlink 6620 can greatly assist and expedite troubleshooting of fiber optic transmission systems and are recommended tools all installers should have available Finally although multimode and single mode devices may look the same they will not operate properly together Using the wrong device or fiber can easily add more attenuation than specified resulting in poor overall performance It should be noted that some of our fiber optic products support both single mode and multimode fiber in the same unit If after reviewing the above possibilities the system is still not operating please contact the Customer Service Department for further assistance If you suspect your problem is caused by the optics or the fiber optic cable and you have an optical power meter please take the appropriate measurements prior to contacting su
10. fiber optic cable and you have an optical power meter please take the appropriate measurements prior to contacting support Maintenance and Repairs Certifications Page 11 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Communications Specialties Inc CSI warrants that for a period of three years after purchase by the Buyer this product will be free from defects in material and workmanship under normal use and service A Return Material Authorization RMA number must be obtained from CSI before any equipment is returned by the Buyer All materials must be shipped to CSI at the expense and risk of the Buyer CSI s obligation under this warranty will be limited at its option to either the repair or replacement of defective units including free materials and labor In no event shall CSI be responsible for any incidental or consequential damages or loss of profits or goodwill CSI shall not be obligated to replace or repair equipment that has been damaged by fire war acts of God or similar causes or equipment that has been serviced by unauthorized personnel altered improperly installed or abused RMA numbers and repairs can be obtained from Communications Specialties Inc 55 Cabot Court Hauppauge NY 11788 USA Tel 631 273 0404 Fax 631 273 1638 or in the Asia Pacific Region Communications Specialties Pte Ltd 100 Beach Road 22 09 Shaw Tower Singapore 189702 Tel 65 6391 8790 Fax
11. ions 4 Installation Instructions 6 Audio Pair Selection 7 Indicator LEDs 7 Application Diagrams 8 Operating Pointers 9 Troubleshooting 9 Maintenance and Repairs 10 Certifications 10 Warranty 11 Accessories and Related Products 12 Contents Page 3 Fiberlink 3353 Series User
12. pport Operating Pointers Troubleshooting Page 10 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Certifications Maintenance and Repairs The Fiberlink 3353 Series has been manufactured using the latest semiconductor devices and techniques that electronic technology has to offer They have been designed for long reliable and trouble free service and are not normally field repairable Should difficulty be encountered Communications Specialties maintains a complete service facility to render accurate timely and reliable service of all products The only maintenance that can be provided by the user is to ascertain that optical connectors are free of dust or dirt that could interfere with light transmission and that electrical connections are secure and accurate Please see the Troubleshooting section of this manual for additional information An optical power meter such as the Fiberlink 6615 a visible light source such as the Fiberlink 6610 and a Three Wavelength Light Source such as the Fiberlink 6620 can greatly assist and expedite troubleshooting of fiber optic transmission systems and are recommended tools all installers should have available All other questions or comments should be directed to our Customer Service Department It should be noted that many problems can easily be solved by a simple telephone call If you suspect your problem is caused by the optics or the
13. s Page 14 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Page 15 Fiberlink 3353 Series User s Manual Fiberlink 3353 Series Fiberlink 3353 Series 3G HD SD SDI to HDMI Optical Receiver World Headquarters 55 Cabot Court Hauppauge New York 11788 USA Tel 631 273 0404 Fax 631 273 1638 info commspecial com Asia Communications Specialties Pte Ltd 100 Beach Road 22 09 Shaw Tower Singapore 189702 Tel 65 6391 8790 Fax 65 6396 0138 csiasia commspecial com commspecial com 2010 Communications Specialties Inc All Rights Reserved Fiberlink and the starburst logo are registered trademarks of Communications Specialties Inc CSI and the triangle designs are trademarks of Communications Specialties Inc P N 128871 Rev C Single Color Black Single Color Black on Black Background If you need to use the CSI logo on a non solid background use the Photoshop Layered Files 2005 Spectra Vision Productions Inc Communications Specialties Fiberlink 3353 User s Manual
14. s Manual Fiberlink 3353 Series Welcome Thank you for purchasing Communications Specialties Inc s Fiberlink 3353 Series The 3353 Series is used to convert 3G HD SD SDI with or without embedded audio transmitted over a single fiber optic core to HDMI The Fiberlink 3353 Series is compatible with single mode or multimode fiber The 3353 is also compliant with SMPTE 297 2006 for seamless interoperability with other SMPTE 297 2006 devices The system delivers noise free transmission that retains all of the signals initial parameters regardless of fiber optic cable attenuation The 3353 Series also provides immunity to video pathological signals over the entire link budget and operating temperature range Features Convert 3G HD SD SDI with embedded audio to HDMI with audio pair selection Supports all SD and HD resolutions to 1080p 60 Fully SMPTE 297 2006 compliant fiber input HDMI embedded and stereo line level outputs if audio present in SDI stream Re clocked SDI BNC output allows for continuous 3G HD SD SDI signal distribution User selection from up to 8 audio channel pairs for multilingual or multimessage support Automatic selection of output resolution no scaling ST and LC fiber connector options Small compact design Compatible with Fiberlink 3350 3360 amp 3380 Series Fiberlink Matrix and Scan Do HD s optical output Package Contents On
Download Pdf Manuals
Related Search