Component I/O Cards Installation Guide
Contents
1. 9 HIGH RISK ACTIVITIES The Software is not fault tolerant and is not designed manufactured or intended for use or resale as on line control equipment in hazardous environments regarding fail safe performance such as in the operation of nuclear facilities aircraft navigation or communication systems air traffic control direct life support machines or weapons systems in which the failure of the Software could lead directly to death personal injury or severe physical or environmental damage High Risk Activities GlobalStreams and its suppliers specifically disclaim any express or implied warranty of fitness for High Risk Activities Any such use is expressly prohibited without prior written agreement of GlobalStreams under terms intended to allocate the risks of selling the insert name here System for such uses You will indemnify defend and hold GlobalStreams harmless from all claims losses damages and expenses including attorneys fees and costs arising from any prohibited use or application of the insert name here System 10 U S GOVERNMENT RESTRICTED RIGHTS If you are a unit or agency of the United States Government U S Government the following provisions apply All Software and accompanying Documentation are deemed to be commercial computer software and commercial computer software documentation respectively pursuant to DFAR Section 227 7202 and FAR Section 12 212 as applicable Any use modifi2. SUPPORT AND MAINTENANCE Support and maintenance services are not provided under this Agreement You must separately contract with GlobalStreams and pay any applicable fees for these services 5 TERM This Agreement is effective upon your initial operation of the insert name here System and shall continue until terminated You may terminate this Agreement at any time by returning the Software and Documentation and extracts therefrom to GlobalStreams Upon such termination by GlobalStreams you agree to return to GlobalStreams all copies and portions thereof of the Software and Documentation GlobalStreams may terminate this Agreement upon the breach by you of any term hereof Termination of this Agreement by GlobalStreams shall not release you from any liability which at the time of termination has already accrued to GlobalStreams or which thereafter may accrue in respect to any act or omission prior to termination or from any obligation specified to survive termination 6 CONFIDENTIALITY You acknowledge that in connection with this Agreement and your relationship with GlobalStreams you may obtain information relating to the insert name here System and to GlobalStreams that is of a confidential and proprietary nature Confidential Information Such Confidential Information may include but is not limited to trade secrets know how inventions techniques processes programs schematics software source documents data customer lists
3. financial information and sales and marketing plans or information that you know or have reason to know is confidential proprietary or trade secret information of GlobalStreams You shall at all times both during the term of this Agreement and for a period of at least five 5 years after its termination keep in trust and confidence all such Confidential Information and shall not use such Confidential Information other than as expressly authorized by GlobalStreams under this Agreement nor shall you disclose any such Confidential Information to third parties without GlobalStreams written consent You further agree to immediately return to GlobalStreams all Confidential Information including copies thereof in your possession custody or control upon termination of this Agreement at any time and for any reason The obligations of confidentiality shall not apply to information that a is in the public domain except as a result of your breach of this Agreement b prior to disclosure hereunder was already rightfully in your possession without an obligation of confidentiality or c subsequent to disclosure hereunder is obtained by you on a nonconfidential basis from a third party who has the right to disclose such information to you Component I O Cards 19 SLORNERMS 7 INDEMNIFICATION You will at your sole expense and GlobalStreams request defend indemnify and hold GlobalStreams and GlobalStreams affiliates or any director
4. where applicable its suppliers GlobalStreams retains ownership of any and all copyrights patent rights trademark rights trade secret rights rights of publicity or privacy or other intellectual property rights Intellectual Property related to or resulting from installation training support and or maintenance of the insert name here System This Agreement does not create any implied licenses All rights not expressly granted are reserved by GlobalStreams You acknowledge that the insert name here System contains trade secrets of GlobalStreams and accordingly you will not use except as authorized herein or disclose the Software or Documentation without GlobalStreams prior written approval and you will use reasonable measures to protect it 3 LICENSE FEES PAYMENT DELIVERY The fees paid by you are paid in consideration of the Hardware and licenses granted under this Agreement Prices and fees are exclusive of all sales use and like taxes and duties All payments must be in United States dollars Any tax or duties GlobalStreams may be required to collect or pay upon sale use licensing or delivery of the insert name here System shall be paid by you to GlobalStreams upon invoice The insert name here System is shipped FOB GlobalStreams site and all transportation charges related FCC Notice GLOBAL SI S to the shipment of the insert name here System shall be paid by you to GlobalStreams upon invoice 4
5. C Component I O Cards Installation Guide GLOBECASTER SLQBNERMS S S www GlobalStreams com 34 336 00 Copyrights Copyright 1998 2002 GlobalStreams Inc All rights reserved The GlobeCaster System software content and documentation are copyright 1998 2002 This User Manual may not in whole or in any part be copied photocopied reproduced translated or reduced to any electronic medium or machine readable format without the prior written consent of an authorized representative from GlobalStreams Inc Trademarks GlobalStreams GlobalStreams and the GlobalStreams logos GlobeCaster and the GlobeCaster logos Warp Engine Preditor Panamation Electric Image Universe Time Machine Personal FX Title Wave GlobeCaster Virtual Sets ClipMem and 3D Video Tracing are trademarks of GlobalStreams Inc Windows and Windows NT are registered trademarks of Microsoft Corporation Bitstream is the registered trademark of Bitstream Inc Artbeats InnoVision Izzy and other trademarks used in the GlobeCaster materials are the property of their respective holders Patents Various technology in the GlobeCaster System is patented in the United States including without limitation patent numbers 5 941 997 5 978 876 5 872 565 Other patents in the United States and othercountries are pending GLQRAERMS ST S Before You Install Any Cards It is important to make a point about electrostatic discharge or ESD Even if you are an experienc
6. ABLE FEES PAID THIS IS A LEGAL AGREEMENT BETWEEN YOU YOUR COMPANY IF APPLICABLE AND GLOBALSTREAMS THIS AGREEMENT REPRESENTS THE ENTIRE AGREEMENT CONCERNING THE INSERT NAME HERE SYSTEM AS DEFINED BELOW BETWEEN YOU AND GLOBALSTREAMS AND SUPERSEDES ANY PRIOR PROPOSAL REPRESENTATION OR UNDERSTANDING BETWEEN THE PARTIES IN THE EVENT OF ANY CONFLICT BETWEEN THIS AGREEMENT AND ANY OTHER DOCUMENT RECEIVED FROM YOU INCLUDING WITHOUT LIMITATION ANY PURCHASE ORDER DOCUMENTATION THE TERMS OF THIS AGREEMENT SHALL PREVAIL 1 GRANT OF LICENSE 1 1 Subject to the terms and conditions of this Agreement GlobalStreams hereby grants to you and you accept a limited personal nonexclusive nonsublicensable nontransferable except in accordance with Section 11 1 license to use each copy of the software object code provided to you including any updates or upgrades provided by GlobalStreams the Software with the tangible equipment provided by GlobalStreams Hardware and the accompanying hardcopy documentation the Documentation the Software Hardware and Documentation collectively constituting the insert name here System for the sole purpose of offering to your customers broadcast production services as authorized in this Agreement You agree that you will not assign sublicense transfer pledge lease rent or share Component I O Cards 17 18 ST your rights under this Agreement You agree that you may not re
7. E levels Factory presets are available for each For more complicated settings or to create your own preset use the Input Settings configure panel RGB 700mV no setup Figure 1 3 Component Input Configure Panel The Component inputs for GlobeCaster can be configured to handle either YUV or RGB component signals To change the input click on the Format In button The input can be set for YUV or RGB component input If you are working with an RGB signal with external sync turn on the External Sync button This button changes two of the pass thru connectors into sync inputs The connector labeled B Y B becomes the Composite or Horizontal Sync input and the connector labeled R Y R becomes Vertical Sync Input The sync doesn t need to be switched it will auto detect composite or H V sync Loop Component I O Cards 9 SNES 10 thru output selection is limited to Composite Luminance out when using external sync To adjust for different levels in YUV such as Betacam or MII there are different factory presents built in These can be loaded from the Input Sources configure panel or into this panel by pressing Load and choosing the preset from the pop up list The factory presets cannot be modified but new presets can be created based on any of the factory settings When saving out your own factory presets change the name of the preset to something different and press Save Your preset value will be added to the list of choic
8. abeling When not using the Black Burst out this output can be used as a composite out put by clicking on the button and choosing Second Output Component I O Cards 11 12 ST N The Genlock Status light is active when a genlock signal is being fed into Globe Caster If the Genlock signal is a valid signal the light will be Green If there is a problem with the signal missing Black Burst or Color Burst or a PAL signal the light will be Red Note that if the Black Out is being used to genlock all other devices this light will be off The status light only reflects what is hooked to the Genlock input The Chroma Bandwidth of the output signal can be set to 2 0Mhz 1 3Mhz 1 0Mhz or 650Khz For component signals the recommended setting is 2 0Mhz When working with composite video the other settings are recommended To be absolutely sure the signal is within NTSC specs set the bandwidth to 650Khz There is an advantage in color quality to bump this value up to 1 0Mhz or 1 3Mhz The Luma Bandwidth can also be adjusted Wide Band brings the signal out to almost 6 0Mhz while Low pass is about 4 0Mhz When sending a signal to a transmitter having the luma bandwidth set a Wide Band can cause interaction with the audio subcarrier and can overmodulate the transmitter Wide band can also cause ringing in certain types of filters If these situations arise it s best to use the Low Pass setting Otherwise the best picture quality can
9. ack of the GlobeCaster about halfway and lift off Figure 1 1 Removing the Retaining Bar 4 Unscrew the thumbscrew on the retaining bars running across the Globe Caster figure 1 1 5 Remove the retaining bar Component I O Cards 5 CLQRAEAMS 6 10 11 12 13 Locate the lockdown panel that holds the backs of the cards in place It is on the inside of the back of the unit It is hinged in place and held down with three thumbscrews see figure 1 2 Figure 1 2 Rear Lockdown Panel Unscrew the three thumbscrews on the rear lockdown panel Lift and rotate the lockdown panel out of the way Remove the backplate from the hole in the back of the slot Line up the new card in the socket Push lightly down on the card BUT DO NOT PUSH THE CARD IN YET Double check a second time to make sure that the card is properly aligned and not binding within the socket PLEASE NOTE THESE HIGH SPEED SOCKETS ARE MUCH MORE FRAGILE THAN STANDARD PC SOCK ETS AND EXTREME CARE MUST BE TAKEN TO MAKE SURE THAT THE MOTHERBOARD IS NOT DAMAGED DURING INSTALLATION Using equal pressure push the card into the socket Make sure the card is in the socket evenly Rotate the rear lockdown panel back into place and tighten up the thumb screws Before You Install Any Cards 14 15 16 17 18 19 20 SNES Replace the retaining bar and tighten the thumbscrew on it Replace the top cover Make sure the bottom e
10. be obtained using Wide Band The Fade Enable button connects this output to the Master Fade to Black button in the Switcher Turning this button off means that this particular output will not be affected by the master Fade to Black Before You Install Any Cards GLQFAEAMS Slave Multi format Output Encoder SVideo Composite Luma Bandwidth Figure 1 5 Slave Multi Format Output Configure Panel The Slave output is pretty straightforward and can be adjusted in the same fashion as the Master Output Keep in mind that the Phasing adjustments are relative to the phase of the master output If the master output is adjusted it will adjust the phasing of the slave output by the same amount Remember that the Fade Enable button controls whether this particular input will Fade to Black when that button is pressed in Switcher By turning the but ton off on a slave output encoder and leaving it on the master encoder only the master encoder will fade to black This gives you added flexibility when sending a Program out feed to several different sources Component I O Cards 13 14 Before You Install Any Cards SLQBAE IM o ST S FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equip
11. cation reproduction release performance display or disclosure of the Software and accompanying Documentation by the U S Government will be governed solely by the terms of this Agreement and will be prohibited except to the extent expressly permitted by the terms herein Manufacturer is GlobalStreams Inc 43 Maryland Plaza St Louis MO 63108 11 MISCELLANEOUS 11 1 You have no right to assign or sublicense this Agreement or any Software licenses in whole or in part without GlobalStreams prior written consent Any attempt to assign or sublicense this Agreement without such consent will be null and void GlobalStreams may assign this Agreement in whole or in part In the event GlobalStreams is acquired this Agreement will continue in accordance with its terms 11 2 This Agreement will not establish any relationship of partnership joint venture employment franchise or agency between you and GlobalStreams Component I O Cards 21 SNES Neither you nor GlobalStreams will have the power to bind the other or incur obligations on the others behalf 11 3 This Agreement shall be construed and governed in accordance with the laws of the State of California excluding its conflict of law rules and venue and jurisdiction for any disputes lie exclusively in Alameda County California You consent to service of process and venue 11 4 Should any term of this Agreement be declared void or unenforceable by any court of competent juri
12. d in the system so do not install more than one of these cards in a GlobeCaster system Also a 34 075 Com posite YC master encoder card cannot be used in conjunction with a 34 08 card If additional outputs are desired suggest the 34 233 Slave Multi format output card to your customer The card provides timing to the entire system in addition to video output Output formats supported are YUV RGB YC 2 BNCs and Composite This card also has BNC connectors for Genlock In Genlock Thru and a configurable connector that provides either Black Burst out or Composite out 34 233 Slave Multi format Output These cards work in conjunction with a Master output encoder to provide addi tional simultaneous outputs to a single GlobeCaster These outputs can be config ured individually to provide multiple output formats Formats supported by this card are Composite Y C RGB and YUV Before You Install Any Cards SLQBA RMS The timing on each slave output card be adjusted relative to the Master encoder allowing signals with different phasing to be outputted simultaneously Also the Fade to Black function in the Switcher can be individually selected on each output so only selected outputs will fade to black Slave output encoders are typically installed in external slots 10 12 Card Installation 1 Turn off the power to the GlobeCaster 2 Unscrew the three thumbscrews along the edge of the top cover 3 Slide the top cover toward the b
13. dges of the top cover fit into the slots on the bottom cover Tighten the three thumbscrews on the top cover Hook the Videonet cables back up to the GlobeCaster Remember to hook RX to TX and TX to RX Now that the card s have been installed we ll fire up the GlobeCaster and test the configuration of the cards Turn the GlobeCaster and the PC on Run the Switcher application from the host PC Component I O Cards 7 GLORAERMs Troubleshooting Tips One quick note to remember while troubleshooting If for any reason you need to remove or reseat a card ALWAYS turn off the power to your GlobeCaster before removing or reseating any card Failure to do so will damage your GlobeCaster sys tem and void the warranty I get an error stating 1 couldn t find attached GlobeCaster system First check the Videonet cables between the PC and the GlobeCaster The cables run from the TX connector on the PC to the RX connector on the GlobeCaster The RX connector on the PC runs to the TX connector on the GlobeCaster If the coordinator card in the GlobeCaster was removed for any reason it might not be properly seated in the sockets Pull the card and reseat it I get an error saying Failure during creation of VEMain Bus The card may not be seated properly in the slot Pull the card and reseat it making sure that the card is fully inserted in the slot Check to make sure that no other cards have been popped loose from the
14. ed technician you should be aware of the danger of ESD Almost everyone is aware of static electricity and its effect when you rub your feet on the carpet and zap someone on the earlobe But did you know how damaging static electricity can be to computer components For a human being to feel a static shock the voltage must be around 1 500 volts Really nasty shocks can be over 30 000 volts Electronic components can be damaged by much lower voltages about 20 30 volts Therefore the static electricity your body accumulates is enough to damage circuit boards by merely touching them Sometimes ESD damage is not readily apparent and can cause a board to fail months after it was improperly handled To avoid this type of failure please take the following steps when working inside your GlobeCaster e Remove any articles of clothing that gather static electricity Wool sweaters are especially prone to this e Work on the GlobeCaster in a reasonably ESD free area Don t work on the unit if it s sitting on a shag carpet e When working on the GlobeCaster keep it turned off and unplugged e Before touching any boards inside GlobeCaster touch the edges of the chassis lightly to discharge any static buildup you may have e Handle only the boards you need to handle Dont go poking around in the unit without a reason AnESD wrist strap costs 5 20 at any electronic supply house and ensures that your body does not have any static charge Ha
15. es in the Input Sources panel Setup Compensate should be turned on in most cases If the input signal does not have Setup then it can be turned off Setup is an old broadcast way of adjust ing the black values in the signal More information about Setup is available in the appendices of the main manual The Format Out is used to choose what the three extra BNC jacks are used for on the back of the input These jacks can provide a buffered Pass thru of the same sig nal being fed into the input module These jacks can also be set up to output a re encoded output after the signal has passed through the color corrector This re encoded output can be in a different format than what goes into the input For example a YUV Betacam signal can be fed in and an RGB signal can be fed out of the re encoded outputs This can also be set up for a composite or luminance out put Because of the limitation of space on the back of the module if external sync is being used for an RGB input signal only Composite or Luminance output is available because the other two BNCs are being used for sync NOTE Keep in mind that the re encoded outputs are designed as Monitor quality out puts with 5 accurate signal levels The buffered pass thru signal levels are 1 accurate or better Clamp Speed is used to adjust the black level on a line by line basis In most sit uations Slow is the best setting for a high quality signal as it is the most immune to random no
16. ion including claims by any guilds or other collective bargaining units or royalty tribunals all of the foregoing claims or actions being referred to hereinafter as Claims GlobalStreams agrees to a provide Client reasonably prompt notice in writing of any such Claims and b provide you reasonable information and assistance at your expense to help defend the Claims You agree to consult with GlobalStreams and obtain GlobalStreams written approval on the choice of any counsel under this section 8 LIMITATION OF LIABILITY GLOBALSTREAMS CUMULATIVE LIABILITY TO YOU OR ANY OTHER PARTY FOR ANY LOSS OR DAMAGES RESULTING FROM ANY CLAIMS DEMANDS OR ACTIONS ARISING OUT OF OR RELATING TO THIS AGREEMENT UNDER ANY THEORY INCLUDING CONTRACT NEGLIGENCE STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY SHALL NOT EXCEED THE AGGREGATE OF THE AMOUNTS PAID BY YOU TO GLOBALSTREAMS FOR THE TWELVE MONTH PERIOD PRIOR TO THE DATE THE CAUSE OF ACTION AROSE IN NO EVENT SHALL GLOBALSTREAMS BE LIABLE FOR ANY INDIRECT INCIDENTAL CONSEQUENTIAL SPECIAL OR EXEMPLARY DAMAGES OR LOST PROFITS EVEN IF GLOBALSTREAMS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THIS SECTION DOES NOT LIMIT LIABILITY FOR BODILY INJURY OR DEATH OF A PERSON SOME STATES DO NOT ALLOW THE FCC Notice GLOBAL a ST S LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL CONSEQUENTIAL OR OTHER DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU
17. ir sockets Make sure you have one master encoder card More than one master encoder card will generate conflicting timing signals confusing your GlobeCaster When I turn on the power for my GlobeCaster it doesn t do anything The fans don t start and the light doesn t even turn on A card is improperly seated in the sockets on the motherboard Immediately turn the power off and re seat the card Make sure that the card is inserted into all appropriate sockets and is pushed down evenly in the unit If the unit still won t start pull the installed card and inspect the sockets on the motherboard for damage There is a slim possibility that the motherboard sockets have been damaged Look for any pins in the socket that look bent or out of shape If so contact tech support immediately Component Configure Panels This section covers the configuration and use of the component cards within the GlobeCaster software These configure panels are available from the Switcher or Editor by clicking on the Configure button Before You Install Any Cards SLQRNERMs When first installing cards check to make sure the card is properly recognized by GlobeCaster by looking at the Installed Cards panel All cards should be recog nized and listed on this panel When configuring an input start by using the Input Sources configure panel and choosing one of the factory presets available The Input module supports both RGB and YUV at Beta MII and SMPT
18. ise in the signal The faster the clamp speed the quicker it tries to compensate for errors in the black level Use a higher clamp speed when trying for example to correct the black level in a signal with a 60Hz hum in the picture Chroma H Delay is used for adjusting out dot crawl in the picture It moves the Chroma values relative to the luminance values Horizontal Centering adjusts the overall center of the image Chroma Gain Trim and Luma Gain Trim These control the A D dynamic range of the Chrominace and Luminance values and are used for adjusting for var Before You Install Any Cards GLQFAEAMS ious Component formats such as SMPTE Betacam and MII levels The value listed is a number in steps from 0 to 255 Before adjusting these values manually try using one of the factory presets by pressing the Load button and choosing from there If the values still do not look up to your equipments specifications on a waveform monitor try adjusting these levels Master Output Encoder Settings Panel Chr Luma Bandwidth VBlank Length Figure 1 4 Master Multi Format Output Configure Panel To change the output format click on the Output Format button and choose the desired output from the pop up menu The Master Output card will show up as Output 10 This differs from the slot on the back of the GlobeCaster which is labeled slot 9 This is normal as the labeling of the slots differs internally from the external slot l
19. ment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interfer ence in which case the user will be required to correct the interference at his own expense Component I O Cards 15 16 FCC Notice GLOBAL ST S GlobeCaster System License Agreement IMPORTANT READ THIS LICENSE AGREEMENT AGREEMENT CAREFULLY BEFORE USING OR OTHERWISE OPERATING THE INSERT NAME HERE SYSTEM BY USING THE INSERT NAME HERE SYSTEM YOU INDICATE YOUR ACCEPTANCE AND AGREEMENT OF THE TERMS AND CONDITIONS OF THIS AGREEMENT GLOBALSTREAMS INC S GLOBALSTREAMS ACCEPTANCE OF YOUR INSERT NAME HERE SYSTEM ORDER IS EXPRESSLY CONDITIONED UPON YOUR ASSENT TO ALL THE TERMS AND CONDITIONS OF THIS AGREEMENT TO THE EXCLUSION OF ALL OTHER TERMS INCLUDING WITHOUT LIMITATION ANY SUPERSEDING OR ADDITIONAL TERMS PROPOSED BY YOU OTHER THAN CONFIRMING AGREED UPON PRICE QUANTITY AND SHIPPING INFORMATION IF THESE TERMS ARE CONSIDERED AN OFFER BY GLOBALSTREAM ACCEPTANCE IS EXPRESSLY LIMITED TO THESE TERMS IF YOU ARE NOT WILLING TO BE BOUND BY THE TERMS AND CONDITIONS OF THIS AGREEMENT YOU SHOULD PROMPTLY RETURN THE INSERT NAME HERE SYSTEM INCLUDING ANY UNOPENED SOFTWARE PACKAGE S AND ACCOMPANYING DOCUMENTATION FOR A FULL REFUND OF APPLIC
20. officers or employee of either collectively the GlobalStreams Parties harmless from all damages claims actions proceedings and or settlements including reasonable attorneys fees and expenses arising out of or in connection with i your activities relating to the insert name here System ii any web site operated controlled or in any way associated with you iii any content used in any manner in connection with your insert name here System other than un modified content supplied by GlobalStreams such content hereinafter referred to as your Media that infringes or violates any Intellectual Property proprietary or contractual right of a third party iv any use of the insert name here System that causes GlobalStreams to violate any agreement GlobalStreams may have with a third party supplier v any defamatory or libelous material or material that discloses private or personal matters concerning any person without such person s consent vi any violations of law or regulations vii your Media or any messages data images or programs that are illegal or are by law obscene profane or pornographic or viii any messages data images or programs that would violate interfere with disrupt or otherwise materially harm the rights of others including unauthorized copyrighted text images or programs trade secrets or other confidential proprietary information or trademarks or service marks used in an infringing fash
21. sdiction such declaration shall have no effect on the remaining terms hereof 11 5 If any action is brought by either party to this Agreement against the other party regarding the subject matter hereof the prevailing party shall be entitled to recover in addition to any other relief granted reasonable attorney fees and expenses of litigation 11 6 The failure of either party to enforce any rights granted hereunder or to take action against the other party in the event of any breach hereunder shall not be deemed a waiver by that party as to subsequent enforcement of rights or subsequent actions in the event of future breaches 11 7 You will comply with the U S Foreign Corrupt Practices Act and all export laws and restrictions and regulations of the Department of Commerce the United States Department of Treasury or other U S or foreign agency and authority and not export or allow the export or re export of any insert name here System in violation of any such restrictions laws or regulations You will obtain and bear all expenses relating to any necessary licenses and exemptions with respect to the export from the U S of any insert name here System to any location FCC Notice
22. verse assemble reverse compile or otherwise translate the Software or create derivative works of the Software or Documentation You will use reasonable efforts to protect GlobalStreams rights under this Section 1 and will notify GlobalStreams of any infringement about which you become aware 1 2 You may make one 1 archival copy of the Software and Documentation provided that you affix to such copy all copyright confidentiality and proprietary notices that appear on the original You may make one copy of the Documentation for backup purposes Except as authorized under this paragraph no copies of the Software or Documentation or any portions thereof may be made by you or any person under your authority or control 1 3 The license in Section 1 1 above will terminate immediately without notice from GlobalStreams if you fail to comply with any provision of this Section 1 Upon termination you will destroy all copies of Software and Documentation or alternatively return all such Software or Documentation to GlobalStreams 1 4 You will not alter erase deface or overprint any notices trademarks emblems legends or other proprietary labels of any nature on or in the GlobeCaster System 2 LICENSOR S RIGHTS You acknowledge and agree that the Software and the Documentation are proprietary products of GlobalStreams protected under U S copyright law Title to the Software and Documentation will at all times remain with GlobalStreams and
23. ving an ESD wrist strap is recom mended but not required Attach the alligator clip of the wrist strap cord to the Trinity chassis or another common ground point Component I O Cards 3 4 ST s Proper Card Placement Within the GlobeCaster Each card in the GlobeCaster has a specific area in the motherboard where the card belongs It is important to understand where each card belongs in order to config ure your customer s system properly 34 209 Component Input Card Normal placement of this input module is in one of the slots labeled 1 7 on the back of the GlobeCaster If this card is going to be the 8th input then the card may be placed in slots 10 12 and this card will be listed as Input 8 on the Switcher Input formats supported are Analog YUV and RGB at adjustable levels Factory presents are included for RGB and SMPTE levels and YUV at Beta and MII levels The loop thru connectors can provide a straight loop out a re encoded loop thru after color correction and a re encoded loop thru in a different format The loop thru can be set for RGB YUV Composite or Monochrome independent of the signal being fed into it In a typical GlobeCaster configuration the master output encoder belongs in slot 34 208 Master Multi Format Broadcast Reference This card belongs in the slot next to the Switcher card inside the GlobeCaster which is slot 9 on the back of the GlobeCaster The GlobeCaster can only have one Master output car
Download Pdf Manuals
Related Search